Agility 4

Installer Manual

Model: RW132V
Important Notice
This guide is delivered subject to the following conditions and restrictions:

This guide contains proprietary information belonging to RISCO Group. Such

information is supplied solely for the purpose of assisting explicitly and properly
authorized users of the system.
No part of its contents may be used for any other purpose, disclosed to any person or
firm, or reproduced by any means, electronic or mechanical, without the express prior
written permission of RISCO Group.
The information contained herein is for the purpose of illustration and reference only.
Information in this document is subject to change without notice.
Corporate and individual names and data used in examples herein belong to their
respective owners.

Compliance Statement
Hereby, RISCO Group declares that the Agility 4 series of central units and accessories are
designed to comply with:

EN50131-1, EN50131-3 Grade 2

EN50130-5 Environmental class II
EN50131-6 Type A
EN50136-1 EN50136-2 and EN50131-10:
PSTN (SP2); GSM 2G/3G (SP4); IP (SP4); GSM primary and IP secondary (DP3)
IP primary and GSM secondary (DP3)
Signaling Security: Substitution security S2
Information security I3
For more information, refer to Appendix F
UK: PD 6662:2017
USA: FCC: Part 15B, Part 15C, FCC Part 68

 2020 RISCO Group. All rights reserved.

Page ii
 Table of Contents

CHAPTER 1 INTRODUCTION ................................................................................. 1

INSTALLING AND SERVICING THE AGILITY 4 SYSTEM ...................................................... 1
KEY BENEFITS .................................................................................................................. 1
KEY FEATURES................................................................................................................. 2
MAIN FEATURES ............................................................................................................... 3
AGILITY 4 ARCHITECTURE ................................................................................................ 4
Traditional .................................................................................................................... 4
Multiple Reporting Destinations ............................................................................... 4
Cloud Communication ............................................................................................... 5
Parallel Communication ....................................................................................................... 5
Back-up Communication ..................................................................................................... 5
Enhanced Capabilities of Multi-Socket Communication Modules....................... 6
Video Verification with IP Camera ........................................................................... 7
Snapshot Follow Event .............................................................................................. 7
TECHNICAL SPECIFICATIONS ........................................................................................... 8
IMPORTANT SAFETY PRECAUTIONS ................................................................................. 9
CHAPTER 2 INSTALLING THE AGILITY 4 ...........................................................10
AGILITY 4 MAIN COMPONENTS ...................................................................................... 10
DESCRIBING THE COMMUNICATION MODULES .............................................................. 11
PSTN .......................................................................................................................... 11
GSM/GPRS ............................................................................................................... 12
IP ................................................................................................................................ 12
Installing the PSTN Module .................................................................................... 13
Installing the IP Module ........................................................................................... 14
Installing the GSM/GPRS Module ......................................................................... 15
Connecting to Wi-Fi ................................................................................................. 16
Installing the Main Panel ......................................................................................... 16
Choosing the Mounting Location ........................................................................... 16
Wall Mounting the Main Panel................................................................................ 16
Installing the Backup Battery .................................................................................. 20
Connecting to the Power Supply - Configuration A............................................. 21
Guidelines for Configuration A .......................................................................................... 21
Grounding Guidelines .............................................................................................. 22
Connecting to the Power Supply – Configuration B ............................................ 23
DIP Switch Settings ................................................................................................. 24
Connecting to a Telephone Line ............................................................................ 25

Page iii
 Connecting a Network Cable .................................................................................. 26
Installing the SIM Card ............................................................................................ 27
Disabling a SIM PIN ................................................................................................. 27
GSM Module LED Indications ................................................................................ 28
External Audio Unit Installation .............................................................................. 29
Completing the Main Panel Installation ................................................................ 29
POWERING UP THE SYSTEM .......................................................................................... 29
CHAPTER 3 INSTALLER PROGRAMMING .........................................................30
PROGRAMMING METHODS ............................................................................................. 30
Allocating the Installer’s LCD/Panda Keypad & Defining the System Language
.................................................................................................................................... 30
Allocating the Customer’s LCD/Panda Keypad & Setting the Default
Language................................................................................................................... 31
Configuration Software ............................................................................................ 32
WIRELESS DEVICE ALLOCATION .................................................................................... 32
Quick Allocation of all Devices at the Main Panel ............................................... 32
Table of Device Transmissions .............................................................................. 33
Device Allocation using the Wireless LCD/Panda Keypad ................................ 34
RF Allocation Method ......................................................................................................... 34
Serial Number Method ....................................................................................................... 34
Zone Allocation Method ..................................................................................................... 35
Allocating Devices using the Configuration Software ......................................... 35
DELETING DEVICES ........................................................................................................ 37
Deleting all Devices Simultaneously from the LCD/Panda Keypad.................. 37
Deleting a Single Device from the LCD/Panda Keypad ..................................... 37
Deleting all Devices Simultaneously from the Configuration Software ............ 37
Deleting a Single Device from the Configuration Software ................................ 38
ESTABLISHING COMMUNICATION TO THE RISCO CLOUD............................................. 38
Step 1: Enabling Cloud Communication ............................................................... 38
Step 2: Defining the (GPRS or IP) Communication Channel ............................ 38
Connecting with GPRS ...................................................................................................... 38
Connecting with IP ............................................................................................................. 38
Step 3: Defining Cloud Parameters for IP or GSM/GPRS ................................. 38
Step 4: Registering the Agility 4 to the RISCO Cloud ......................................... 39
IRISCO SMARTPHONE APP ........................................................................................... 39
PIR CAMERA SETUP ...................................................................................................... 39
CHAPTER 4 INSTALLER MENUS .........................................................................41
DESCRIBING THE WIRELESS LCD/PANDA KEYPAD....................................................... 41
ACCESSING THE INSTALLER MENUS .............................................................................. 41
PROGRAMMING MENU .................................................................................................... 42

Page iv
 1. System Sub-Menu ............................................................................................... 42
1.1 Timers ............................................................................................................................ 43
1.2 Controls ......................................................................................................................... 45
1.3 Labels ............................................................................................................................ 56
1.4 Sounds .......................................................................................................................... 57
1.5 System Settings ........................................................................................................... 58
1.6 Service Information ...................................................................................................... 58
1.7 Firmware Update ......................................................................................................... 59
1.8 Picture Server ............................................................................................................... 59
2. Programming: Radio Devices Menu ................................................................. 60
2.1 Allocation ....................................................................................................................... 60
2.2 Modification ................................................................................................................... 61
2.2.1 Zones...................................................................................................................... 61
2.2.2 Remote Controls ................................................................................................... 82
2.2.3 Keypads ................................................................................................................. 84
2.2.4 Sirens ..................................................................................................................... 86
2.2.5 Wireless I/O Expander ......................................................................................... 88
2.3 Identification.................................................................................................................. 96
2.4 Delete ............................................................................................................................ 96
3. Programming: Codes Menu ............................................................................... 97
3.1 User ............................................................................................................................... 97
3.2 Grand Master ................................................................................................................ 98
3.3 Installer .......................................................................................................................... 98
3.4 Sub-Installer.................................................................................................................. 98
3.5 Code Length ................................................................................................................. 99
3.6 DTMF Code .................................................................................................................. 99
3.7 Parent Control .............................................................................................................. 99
4. Programming: Communication Menu ............................................................. 100
4.1 Method Sub-Menu ..................................................................................................... 100
4.1.1 PSTN .................................................................................................................... 100
4.1.2 GSM...................................................................................................................... 102
4.1.3 IP ........................................................................................................................... 106
4.2 Monitoring Station ...................................................................................................... 109
4.3 Configuration Software .............................................................................................. 116
4.4 Follow-Me.................................................................................................................... 118
4.5 Cloud ........................................................................................................................... 124
5. Programming: Audio Messages Menu ........................................................... 126
5.1 Assign Message ......................................................................................................... 126
5.2 Local Message ........................................................................................................... 126
TESTING MENU ............................................................................................................. 127
1. Main Unit ............................................................................................................. 128
2. Zone ..................................................................................................................... 129
3. Keyfob ................................................................................................................. 130
4. Keypad ................................................................................................................ 130

Page v
 5. Siren..................................................................................................................... 131
6. GSM ..................................................................................................................... 132
7. IP Unit .................................................................................................................. 133
8. UO Unit ................................................................................................................ 133
ACTIVITIES MENU ......................................................................................................... 134
FOLLOW ME MENU ....................................................................................................... 135
CLOCK MENU ............................................................................................................... 135
EVENT LOG MENU ........................................................................................................ 136
MACRO MENU .............................................................................................................. 136
Programming Macro Keys .................................................................................... 136
Activating a Macro.................................................................................................. 137
APPENDIX A: REPORT CODES ........................................................................ 138
APPENDIX B: INSTALLER EVENT LOG MESSAGES .................................... 143
APPENDIX C: LIBRARY VOICE MESSAGES .................................................. 148
APPENDIX D: REMOTE FIRMWARE UPGRADE ............................................. 149
APPENDIX E: INSTALLER PROGRAMMING MAPS ....................................... 155
APPENDIX F: EN 50131 AND EN 50136 COMPLIANCE ................................ 165
APPENDIX G: SIA CP-01 COMPLIANCE .......................................................... 168
APPENDIX H: AGILITY 4 ACCESSORIES ........................................................ 170

Page vi
Chapter 1 Introduction
RISCO Group's Agility 4 elegantly combines state-of-the-art video verification utilized
from Cloud-based Smartphone / Web apps with advanced wireless security and safety
features. Monitoring stations and/or designated system users can now identify false
alarms, as video verification helps enable immediate confirmation of an intrusion-in-
progress, thereby prioritizing response, increasing efficiency, and giving you on-the-go
control and monitoring of your protected site.

Connecting the system to the RISCO Cloud server also enables Smartphone and Web
interface users to control and manage their systems remotely, including the ability to arm
and disarm the system and perform other operational, programming, and maintenance
functions.

The Agility 4 also offers one or more multi-socket communication modules (IP, GSM 2G or
GSM 3G) that provide multiple, simultaneous communication channels for direct
communication, and for communication via the Cloud.

Featuring a simple installation, and a comprehensive range of peripherals, Agility 4 is the

ideal wireless solution for residences and small businesses.

Installing and Servicing the Agility 4 System

The Agility 4 system is intended to be installed and serviced only by an alarm system
installer (or similar professional, such as electrician). The system is not intended to be
installed or serviced by the user / customer.

Key Benefits
Flexible plug-in primary / backup communication modules:
 IP module
 GSM/GPRS module
 Fast PSTN module
2-way wireless LCD/Panda keypad with full programming capability
2-way 8 button wireless remote control with code protection, key-lock and system
status request and indication
2-way voice communication
Easy enrolling of wireless devices without a keypad
Remote enrolling according to device serial number
Can combine 1–way or 2-way transmitting devices in the same system
Flash memory for easy firmware upgrade
Simple physical installation with wall brackets
Separate main panel, can be hidden for higher security

Page 1
 Simplified menu logic (only menus of installed devices are displayed, only menus
according to the authorization code are displayed)
Full voice-guided menu for remote system operation

Key Features
32 wireless zones
3 partitions
Up to 3 bi-directional wireless keypads
Up to 8 rolling code keyfobs
Input/output module:
 2-way wireless communication to the Agility 4
 Local transformer with rechargeable backup batteries
 4 wired zones with selectable EOL resistance & 4 outputs (2 x 3A and 2 x 500 mA
relays)
 Includes X-10 adaptor
32 user codes + Grand Master code
1000 event log
Uses regular sealed lead acid battery 6V 3.7 Ah
16 Follow Me destinations
2-way listen-in and talk with VOX
Supports 2-way wireless curtain detectors
Supports magnetic door/contact detectors with shutter
Supports video verification with IP cameras
Supports Snapshot Follow Event

Page 2
Main Features

Detectors Monitoring Station Communication Installer Programming

 32 Wireless zones:  Remote programming,  Flexible multi-socket  Local /Remote using
 4 Wired zones via diagnostics and communication over Configuration Software
optional Wireless I/O communication test. GSM/GPRS, IP or PSTN.  Program transfer
Expander  Report to 3 MS.  Backup capability via the module.
 Total zones: 36  Report through PSTN, Cloud by IP &  Full programming using
 More than 25 zone types GSM/GPRS or IP. GPRS/GSM bi-directional wireless
 Full zone supervision  MS polling through IP  Supports major reporting keypad.
 2-way and 1-way network. formats.  Flexible device
detectors combined on  Account number for each  Add on module for each enrollment by serial ID
the same system MS. communication type. serial number or by RF
 Image capture and  Flexible split reporting  Cloud Support allocation.
transmission via camera for backup.  Keypad programming
 Snapshot Follow Event  Call Save mode for non- menu adjusted to
urgent reports. existing hardware
 Remote device enrollment
2-way LCD Keypad User Operating Tools
 Fully Wireless  2-way 8 button key fob
 LCD display  Bi-directional Keypad
 S.O.S / Two way  4 button keyfob
communication  Remote phone operation
emergency key  SMS
 Double tamper  Configuration software
protection (Box & Wall)  Web browser
 2-Way Wireless Slim  Smartphone App for self-
Keypad Reader monitoring
2-way Panda Keypad
 Fully Wireless
 S.O.S / Two way
communication
emergency key
 Double tamper
protection (Box & Wall)
 Proximity Tag operation
 Battery economy mode
Follow Me: Wireless Features Voice capabilities Home Automation
 16 follow me  Signal jamming  2-Way communication  4 outputs via wireless
destinations indication  Remote phone operation I/O expander
 Follow me can be  Receiver calibration  Full voice menu guide  16 X-10 outputs via
defined as voice  868MHz/433 MHz radio  System event messaging wireless I/O expander
message, SMS, Email or frequencies  Local announcement  Outputs can follow
to smartphones  Programmable messages system, partition, zone or
 User control over the supervision time  Voice description for user events
system  Tamper detection in zones, partitions, etc.  Outputs can be
 Security code protection transmitters scheduled, or activated
 Unlimited email  Low battery detection in automatically, or by user
destinations from the transmitters command (SMS, Web
Cloud server browser or remote phone)
Codes Video Verification Sirens False Alarm Reduction
 1 installer code  One or more IP Cameras  Built-in siren  Swinger shutdown
 1 sub installer code (inside and outside)  Fully wireless external  Zone crossing
 1 grand master code  Up to 8 eyeWave™ PIR and internal wireless  Report delay to MS
 32 user codes cameras sirens  Abort alarm feature
 4 authority levels  Smartphone/Web access  Up to 3 Sirens  Soak test
 Optional 4 or 6 digits  False alarm reduction  Final exit zone
code definition

Page 3
Agility 4 Architecture

Traditional
Agility 4 can communicate information to monitoring stations (and Follow Me
destinations) through various communication channels, depending on the physical
communication modules installed inside the main panel. Communication can be
established through PSTN, IP, or GSM/GPRS.
All methods can be used for:

Reporting events to monitoring stations

Sending automatic notifications to the owner
Remote system programming and maintenance
Owner remote control

Multiple Reporting Destinations

System Users: System users can use the Cloud-based iRISCO smartphone and Web
User interface for receiving event notifications. Also, multiple Follow-Me recipients
are notified of events via voice (voice mail), SMS, or e-mail.
Monitoring Station: Events are reported to monitoring station(s) directly or via the
RISCO Cloud, in any of the supported channels. Agility 4 supports all major
monitoring station reporting formats and protocols - including direct connection to
the monitoring station or via the Cloud using SIA IP.
Installer: According to how the system is programmed, installers can also receive
Follow-Me reporting, just like system users.

Page 4
Cloud Communication
Agility 4 can be constantly connected to a dedicated application server (the “RISCO
Cloud”) via IP or GPRS.
The RISCO Cloud handles all communication between the Agility 4 system, monitoring
stations and Smartphone/Web users, enabling remote monitoring and control, as well as a
RISCO’s VUpoint video verification solution that utilizes IP cameras:
Cloud communication can be defined as either parallel or back-up.
Parallel Communication
Parallel communication can be accomplished as follows:
If using single-socket communication modules (IP and GPRS/GSM), one of the
modules is connected to the Cloud, while the other module is connected directly (for
example, for reporting to the monitoring station). Each single-socket module supplies
a single communication channel, thus providing the “parallel” communication
capabilities by utilizing the two modules.
If using multi-socket modules (IP, GSM 2G, GSM 3G) a single multi-socket module
provides multiple communication channels simultaneously (“in parallel”) – for
example, for user reporting via the Cloud while simultaneously reporting to the
monitoring station directly. If two multi-channel modules (IP and GSM) are installed,
each module provides its own parallel communication capabilities
Back-up Communication
Backup communication can be accomplished as follows:
If using single-socket communication modules (IP and GPRS/GSM), a total of two
communication channels are available – one channel per module, which can utilize a
variety of reporting frameworks – directly, and through the RISCO Cloud (for
example, one channel reporting to the user via the Cloud, while the other channel
simultaneously reporting directly to the monitoring station). Each of these modules
can be used for the primary communication. NOTE: PSTN can also be used as a
backup or primary channel to the monitoring station.
If using multi-socket modules (IP, GSM 2G, GSM 3G), any individual multi-socket
module installed can provide multiple, simultaneous communication channels with a
variety of reporting frameworks, both directly and through the RISCO Cloud – for
example, one channel reporting to the user via the Cloud, while the other channel
simultaneously reporting directly to the monitoring station. If both IP and GSM multi-
socket modules are installed, when utilizing direct communication either of the
modules can take over and connect as a communication failure backup if the other
fails. NOTE: PSTN can also be used as a backup or primary channel to the monitoring
station.

Page 5
Enhanced Capabilities of Multi-Socket Communication Modules
Multi-socket communication modules each provide multiple, simultaneous communication
channels for services and reporting (for example to the user and monitoring station) –
directly, or via the Cloud. Multi-socket module services and reporting abilities include:
iRISCO Smartphone app & Web user interface: Connected via RISCO Cloud
Monitoring Station: Direct connection using SIA-IP, or with the RISCO IP Receiver
installed at the monitoring station
Configuration Software: Connection with panel via RISCO Cloud or directly using
various channels, including GSM & IP networks – see CS documentation
Follow-Me: Events are sent to FM destinations by E-mail, SMS, or voice
SynopSYS: Connection via IP / GPRS

Page 6
Video Verification with IP Camera
Agility 4 supports RISCOs revolutionary, live VUpoint video verification solution which
seamlessly integrates an unlimited number of IP cameras to provide an unprecedented
level of security and live video monitoring capabilities to monitoring stations and
end-users alike. Powered by the RISCO Cloud, VUpoint enables the initiation of live video
streaming on demand from any IP camera which can be viewed directly using the iRISCO
smartphone or Web applications. VUpoint can be configured so that any detector or event,
whether intrusion, safety or panic, can trigger the IP camera. For verification purposes,
users can monitor intrusion events using snapshot images and live video, and monitoring
stations can identify costly false alarms for higher efficiency.
Snapshot Follow Event
Agility 4 also supports advanced PIR camera functionality to “follow” (capture and send
snapshots) of event activations – other than those of the PIR camera itself – which occur
within the PIR’s partitions. This, together with video verification, enables comprehensive
visual verification capabilities for your system.

Page 7
Technical Specifications
The following technical specifications are applicable for the Agility 4:

Electrical Characteristics
Power 230 VAC (-15%+10%), 50 Hz, 50 mA
Main board: Typically 130 mA
Units consumptions GSM: Standby 35 mA, Communication 300 mA
Modem: Standby 20 mA, Communication 60 mA
IP Card: 115 mA (max)
Backup battery Sealed lead acid battery 6V 3.7 Ah
Voice Configuration External, in parallel with internal or additional external
Audio Unit
Internal Siren intensity 100 dBA @1 m
Operating temperature -10°C to 55°C (14°F to 131°F)
Storage temperature -20°C to 60°C (-4°F to 140°F)
Physical Characteristics
Dimension 268.5 mm x 219.5 mm x 64 mm (10.57 x 8.64 x 2.52 in)
1.31 kg (2.9 lbs) –full configuration
Weight (no battery)
GSM module: 45 gr. (.1 lbs)
IP module: 34 gr. (.07 lbs)
Wireless Characteristics
Radio Immunity According to EN 50130-4
868.65 MHz: 10mW Max.
Power Output
869.525 MHz: 100mW Max.
Frequency 868.65 MHz or 433.92 MHz
Camera Frequency 869.525 MHz, 916 MHz, 430 MHz

Page 8
Important Safety Precautions

WARNING: Installation or usage of this product that is not in accordance with the
intended use as defined by the supplier and as described in the instructional
materials can result in damage, injury or death.

WARNING: Make sure this product is not accessible by children and those for whom
operation of the system is not intended.

WARNING: Customer should never attempt to repair the wireless security alarm
system or component, nor try to open the main panel casing, as doing so could result
in damage, injury or death – customer should always contact your installer /
supplier agent for service.

WARNING: This main panel should be connected to an easily-accessible wall outlet,

so that power can be disconnected immediately in case of malfunction or hazard. If
the unit is permanently connected to an electrical power supply, then the connection
should include an easily-accessible disconnection device, such as a circuit breaker.

WARNING: Coming into contact with 230 VAC can result in death. If the main panel
is opened while it is connected to the electrical power supply, be extremely careful
not to handle the power supply module or other hardware that is connected to the
230 VAC.

WARNING: Risk of explosion exists if a battery is replaced by an incorrect type.

CAUTION: Dispose of used system component batteries according to applicable law

and regulations.

Page 9
Chapter 2 Installing the Agility 4
Agility 4 Main Components
The illustration below shows the internal components when the main panel’s mounting
bracket (back cover) is detached from the main panel housing.

Main Panel Bracket –

Configuration A:
1 Main panel mounting
bracket
2 Telephony terminals
3 Terminal block
(peripherals, ground)
4 Ribbon cable jack
5 AC connection terminals
(or DC socket)
7 Transformer

Main Panel Bracket –

Configuration B
1 Main panel mounting
2 bracket
2 Telephony terminals
3 Terminal block
3 (peripherals, ground)
4 Ribbon cable connector
4
1 5 AC connection terminals
(or DC socket)

Page 10
 Main Panel Housing
8 8. Main panel
9. SIM card holder
9

LOCK
OPEN
10. Ribbon cable
11. DIP switches
10 18
12 PTM connector
13 RS 232 connector
11
ON

1 2 3 4

14. Battery compartment

12 17 (shown with battery
13
removed)
15. Battery compartment
14 cover
16 16. Battery connectors
17. Tamper switch
18. IP card network connector

15

Describing the Communication Modules

PSTN

The Agility 4’s PSTN modem is an easy-to-add plug-in module that enables a typically
inexpensive PSTN connection, for use as either the primary communication channel or as a
failure back-up channel to Cloud communication via GSM/GPRS or IP. The modem
enables the panel to communicate with a monitoring station using common format
protocols (SIA, Contact ID).

Page 11
GSM/GPRS
The easily-installed Agility 4’s GSM/GPRS plug-in module enables system communication
over 2G/3G networks for both users and monitoring stations, for event reporting, system
control, and programming. GSM/GPRS can be used as the primary communication
channel, or as a failure back-up for IP or PSTN communication channels.
GPRS connectivity enables the system to be constantly connected to the RISCO Cloud,
which in turn enables visual verification to end users and monitoring stations alike, and
provides end users with system control via the Smartphone and Web applications.
Cloud-connected users can receive real-time push notification messages to Smartphones, or
e-mail notifications.

Without Cloud connectivity, users can additionally control the system using DTMF or
SMS, and can also be configured to receive event notifications via SMS, voice messages,
and e-mail (in parallel to the Cloud-based notifications), depending on system
configuration. Reporting events to monitoring stations is via GPRS, voice, or SMS (using
the RISCO IP Receiver). Events can be reported in SIA, SIA IP, and Contact ID monitoring
protocols. The GSM/GPRS module also supports two-way voice communication between
users and the monitoring station, which can be beneficial for elderly care, especially in
times of emergency.

IP
The easily-installed Agility 4’s IP plug-in module enables system communication over a
TCP/IP network. It can be used as the primary communication channel or as a failure back-
up for GSM/GPRS or PSTN communication channels.
Using IP connectivity, the system can be constantly connected to the RISCO Cloud server,
which enables visual verification to end users and monitoring stations alike, and provides
end users with real-time event reporting and system control via the Smartphone and Web
applications. The IP module also enables users to receive e-mail alerts and system status
information.
The IP module supports common format protocols (SIA, Contact ID) to send alerts to
monitoring stations using the RISCO IP Receiver.
The IP module also enables remote programming of the system main panel using the
Configuration Software over an IP line.

Page 12
Installing the PSTN Module

Page 13
Installing the IP Module

Page 14
Installing the GSM/GPRS Module

NOTE: For the 3G module, attach the GSM

antenna using the double-sided adhesive.

Page 15
Connecting to Wi-Fi

To Connect to Wi-Fi
Note: Your Router’s Wi-Fi must be activated for the Control Panel to recognize and
communicate with the Router.
1. To connect via Wi-Fi network, you must select your Router’s Wi-Fi network.
2. Go to Activities –> Wi-Fi screen: available networks appear in a list.
3. Select the desired network and enter the password (if required).
Installing the Main Panel

IMPORTANT: Only alarm system installers or similar professionals (such as electricians)

should install and service the Agility 4 system.

Choosing the Mounting Location

Before you mount the main panel, study the premises carefully in order to choose the best
exact location. The mounting location should be:
Centrally located among the wireless system transmitters
In a protected area, that is not visible from outside of the protected premises
Mounted a minimum of 1.2 to 1.5 meters from the floor, in order to achieve optimal
supervision communication with the peripheral devices
Not reachable by small children
Near an uninterrupted 230V AC electrical outlet
Near a telephone outlet or IP network cable outlet if either is used
In an area with a good GSM reception level
In a place where the alarm can be heard during Partial Arming mode
Far from:
 Direct heat
 Sources of electrical disturbance
 Large metal objects, which may hinder the antenna reception.

Wall Mounting the Main Panel

The main panel is comprised of two sub-assemblies:
Mounting bracket
Main panel which in its turn is comprised of:
 Front panel (not disassembled on a regular installation procedure)
 Back panel
The mounting bracket is mounted on the wall, using the supplied proper hardware, as
described below:

To mount the main panel on the wall:

Page 16
1. Separate the mounting bracket as follows:

2. Release the mounting bracket captive locking screws (Figure 1, detail 1) located at the
bottom of the unit, by turning screws counter-clockwise.

Figure 1: Mounting Bracket screws

3. Gently, pull up the mounting bracket to a 45° angle and slide it down to release the
mounting bracket (Figure 2, detail 2) from the two locking tabs (Figure 2, detail 1) at
the top of the unit.

NOTE: Do not open the mounting bracket to a larger angle in order not to break the
two top tabs and not to tear up the ribbon cable connecting the power supply module
(PCB) to the front panel module.

4. Disconnect the ribbon cable (see Figure 2, detail 3) from the power supply module
while leaving it connected to the main panel.

Figure 2: Mounting Bracket removal

5. Hold the mounting bracket against the wall as a template and mark the locations for
the 5 mounting holes and an additional hole for securing the tamper protection
bracket item (see Figure 3, detail 2), are available,).

6. Drill the desired mounting holes and install the anchors to the wall. Use the supplied 5
Philips pan head screws to attach the mounting bracket to the wall (ST4.2 mm x 32
mm DIN 7981).

Page 17
7. According to the location of the wall cables, route and insert the wires and cables via
the cable’s openings (see Figure 3, detail 3) including AC cable and telephone cable.
See the following sections on wiring/connection tasks.

8. Anchor cables with dedicated hooks (see Figure 3, detail 4).

1
1

4
4

3
3 3
3

2
2

1
1

Configuration A
Configuration B

Figure 3: Wall Installation

9. Adjust the tamper switch (using a small flathead screwdriver) according to your
preferred configuration:
a. Box and Wall configuration (see Figure 3, detail 6) - Triggers the tamper when the
box (main panel) or the wall mounting are tampered with.

Page 18
b. Box only configuration (see Figure 3, detail 7) – Triggers the tamper when the box
(main panel) is tampered with.

Page 19
Installing the Backup Battery
Agility 4 has a safety approved, sealed lead acid 6V, 3.7 Ah rechargeable backup battery
for use in case of a power failure:

WARNING: Risk of explosion exists if battery is replaced by an incorrect type.

CAUTION: Install with correct polarity.
CAUTION: Dispose of used batteries according to applicable law and regulations.

To install the backup battery:

1. Remove the battery cover screw (see Figure 4, detail 3) and pull the cover outward.

Figure 4: Battery Compartment

2. Insert the battery into its place and attach the connectors with the correct polarity.

3. Reinstall the battery cover and secure it with the locking screw.

NOTE: The rechargeable battery should be charged for at least 24 hours.

Page 20
Connecting to the Power Supply - Configuration A
For this configuration, the Agility 4 main panel is permanently connected to the mains via
wall power supply or circuit breaker. The connection must be made in compliance with
applicable electrical code and regulations. The Agility 4 is powered by a safety-approved
230 VAC.
Guidelines for Configuration A
 Connect the Live, Neutral and Ground using a safety-approved 3-wire, 18 AWG
power cable (14-mm minimum diameter, flexible PVC cable that complies with
IEC60227). The cable should be brought to the main panel in a protective plastic
conduit, with a 16mm minimum diameter.
 A 2-pole 16A circuit breaker and earth leakage protector should be used to disconnect
the live conductor, and should be provided as part of the building installation.

To connect the power supply cable to the panel:

NOTE: The power cable is not supplied with Agility 4 system

1. Remove the power supply unit cover

2. Connect the power cable (safety approved, SVT, 18AWG, 0.75mm2) the power supply
terminals located on the power supply PCB.

Figure 5A: Connecting AC power cable wires

3. DO NOT connect the power cable to the electrical power supply at this point.

4. Ensure proper grounding (see Grounding Guidelines, page 22).

Page 21
Grounding Guidelines

WARNING: The system must be connected to a protective grounding terminal in the

building installation. Use a min 18 AWG yellow/green conductor for this connection

Grounding provides a degree of protection against lightning and induced transients for
any piece of electronic equipment that may, due to lightning or static discharge,
experience permanent or general malfunctions. The ideal ground is considered to be a
unified earth ground in which an 8-foot copper-clad rod, located close to the existing
power and telephone ground rods, is sunk several feet into the earth. Appropriate
hardware and clamps are then used to electrically connect each of these rods together and
then to the ground terminal of the device to be protected.
It may be possible to use an existing electrical ground on the premises if one is close
enough to the Agility 4. When connecting the ground wire, use a solid 14-gauge wire [or
larger (numerically lower) size]. Keep this wire as short as possible and do not run it in
conduit, coil it, bend it sharply, or run it alongside other wiring. If you must bend it or
change its direction, it should have a radius of at least 8 inches at the point from which it is
bent. If in doubt, you may want to enlist the help of a licensed electrician in matters
concerning such grounding.

To ground the Agility 4 system:

 Connect the Agility 4 ground terminal to an adequate electrical grounding

connection for the lightning transient protective devices in this product to be
effective.

WARNING: The Agility 4 connection to a grounding terminal must be performed

according to applicable electrical code and regulations.

Page 22
Connecting to the Power Supply – Configuration B

In this configuration, the Agility 4 main panel is powered via a 9 VDC / 1.0 A transformer.

1. Connect the transformer plug into the DC socket located on the bracket module (PCB).

2. Route the cable through the hook and opening on the bracket.

3. DO NOT connect the transformer’s power cable to the wall power supply at this
point.

From 9VDC/1.0A
Transformer

Figure 5B: Connecting DC Power Cable

Page 23
DIP Switch Settings

IMPORTANT: As of Agility 4, DIP switches 1–4 in previous versions have been shifted to
2–5, respectively. DIP switch 1 is for future use.

DIP Switch 1: (future use)

DIP Switch 2 (E-A): External Audio: Used to define if the audio from the system will be
heard from the control panel or from an external audio unit. If an external unit is
connected to the Agility 4 system, the audio will be heard only through the external audio
unit.
 ON: External audio unit is connected to the Agility 4 system
 OFF (Default): External audio unit is not connected to the Agility 4 system

DIP Switch 3 (DFLT): Default jumper: Used when performing the following:
1. To return installer, sub-installer and grand master codes to their default factory
values. Set this DIP switch to ON, disconnect all power and then reconnect the power.
Note the code length does not change.

WARNING: When performing this procedure, the main panel is open, so be extremely
careful not to handle the power supply module, or any other components connected to 230
VAC. Coming into contact with 230 VAC can result in death.

2.

DIP Switch 4 (PRGM): Enables loading local software updates to the Agility 4
 ON: software updates to the Agility 4 can be loaded
 OFF (Default): software updates to the Agility 4 cannot be loaded

DIP Switch 5 (BAT): Defines the Battery Discharge Protection option settings
 ON: Battery Discharge Protection is OFF: The battery may therefore become totally
discharged during a continuous AC power outage, thus battery replacement may be
required (no “deep discharge” protection).

NOTE: In this position the system will start to operate from the backup battery

Page 24
 whether or not it is connected to the AC power supply (wall outlet / circuit breaker).

 OFF (Default): Battery deep Discharge Protection is ON: If an AC power outage occurs,
the system automatically disconnects the backup battery when its voltage drops below
5.8 VDC, in order to prevent "deep discharge” that may damage the battery.

NOTE: In this position the system will not start to operate from the backup battery,
unless first connected to the AC power supply (wall outlet / circuit breaker).
NOTE: If the battery voltage drops below 5.8 V or it is not connected, its keypad menu
reading is “0.0”.

Connecting to a Telephone Line

Connect the system to a telephone line if the system configuration includes an internal
modem (identical for configuration A and B).

1. Connect the incoming telephone line to the LINE terminal.

2. Connect a telephone on the premises to the SET terminal.

NOTE: To ensure line seizure capability, and comply with FCC part 68 regulations, the
equipment must be connected directly to the Phone company lines ('CO'). Whether
connected via RJ11, RJ31, the line port must be connected to the CO lines without any other
phones or other telecom equipment between them. Other telecom equipment can be
connected only after (in series) the alarm panel.

Figure 6: Telephone Line Wiring

Page 25
Connecting a Network Cable
If your Agility 4 system is equipped with an IP card, connect the incoming network cable
to enable IP communication.

1. Separate the main panel from its mounting bracket.

2. According to the location of the network cable, route and insert the cable via the
opening on the main panel (see Figure 3, page 18).

3. Connect the incoming network cable to the Ethernet connector.

Figure 7: Network Cable Wiring

Page 26
Installing the SIM Card
If your Agility 4 system is equipped with a GSM/GPRS module, insert a SIM card in order
to enable GSM/GPRS communication.

CAUTION: Do not install SIM card while the main panel is powered up.
CAUTION: Do not touch SIM Card circuitry /connectors, as it could damage the SIM card.

1. Insert the SIM into the dedicated SIM card slot located on the rear side of the back
panel.

SIM Card
OPEN

OPEN
LOCK

LOCK
OPEN
LOCK

1. Slide down SIM 2. Open the SIM card 3. Close the SIM card
card hatch . hatch. Insert SIM card hatch . Slide up to lock.
into dedicated slot.

Figure 8: Installing the SIM Card

2. If a PIN code is required for the SIM card, a trouble code will appear. To remedy, enter
the PIN code at the following location: Communication > GSM parameters menu.

NOTE: Ensure that you enter the correct PIN code. After three wrong attempts, the
SIM card may lock and you may have to contact your provider to unlock it.

Disabling a SIM PIN

1. Insert the SIM card into a standard GSM mobile phone.
2. Insert the PIN code.
3. Access the phone security menu and select PIN OFF. Once done, re-test by switching
the phone off, then switching it on. The PIN code should not be requested again.
4. Once the SIM card is inserted it is recommended to test the operation by conducting a
call and testing the GSM signal strength. For more information, refer to the
programming menus of the GSM menu.

NOTE: In some countries an SMS center phone number might be required in order to
enable SMS messaging. This phone number is provided by the provider.
Programming the SMS center phone into the SIM can be done using a standard GSM
mobile phone or from the wireless LCD/Panda keypad or Configuration Software.

Page 27
GSM Module LED Indications

LED Function
1 LD2: On=power on, off= no power
NOTE: After powering up the GSM module with the SIM card installed, the module
performs an automatic test of the GSM signal (RSSI) level.
For the first 30 seconds after powerup, the red LD2 repeatedly flashes from 0–5
times (with a 5-second delay between each flashing cycle) to indicate the RSSI level:
5 flashes: very high
4 flashes: high
3 flashes: medium
2 flashes: low
1 flash: very low
0 flashes: no network connection
If the signal level is not satisfactory or poor, consider installing the GSM in a
location with better signal reception.
2 LD4: After power-up, LD4 blue LED starts to blink slowly ON and OFF in equal
intervals after the modem is woken up.
When the modem is ready and initialization has started, the ON/OFF intervals
change – short interval ON and long interval OFF
When initialization is finished successfully and the module has received parameters
from the panel, LD2 red LED is constantly ON and LD4 blue LED continues to blink
in short intervals ON and long intervals OFF.
3 LD3: The green LED is ON while module is in some activity – voice, internet etc.
4 LD1: Yellow LED indicates that the module is stuck
NOTES:
1. During burning software, all LEDs blink at different speed.
2. If after power-up there is no SIM card or the module cannot register to a network or the panel does
not send parameters, it remains in the state of blue LED blinking slowly in equal ON/OFF intervals.

Figure 9: GSM Module LEDs

Page 28
External Audio Unit Installation
The system can be connected to a remote external audio unit to be used instead of the main
panel’s internal speaker for listening to the system's audio messages. In addition, the
external audio unit enables you to talk to your protected premises.

To connect the external audio unit:

1. Wire the external audio unit to the terminal block, located on the bracket’s power
module (PCB), as per the following figure.

2. Set DIP switch 2 (E- A) to the On position (see DIP Switch Setting, page 24).

Audio Unit Terminals on External Audio Unit

the Mounting Bracket

AUX GND TMP MIC SPKR

IN OUT AUX COM TMP

AUDIO RED BLK LED

Figure 10: Wiring the External Audio Unit

Completing the Main Panel Installation

1. Re-connect the ribbon cable connecting the main panel and the mounting bracket.

2. Mount the main panel onto the mounting bracket using captive locking screws.

Powering Up the System

After completing all the tasks for module installation, backup battery installation, electrical
power supply and terminal board wiring, grounding, DIP switch setting, closing up the
main panel and mounting it, you can now power-up the system.

 Power up the system by applying electrical power at the wall outlet or circuit breaker.

Page 29
Chapter 3 Installer Programming

Programming Methods
The following options are available for the installer to program the Agility 4 system:

NOTE: The Agility 4 can be programmed only using one keypad at a time.

Temporary “ Installer” LCD/Panda Keypad (typically used for example, if customer’s

kit doesn’t include an LCD keypad)

Customer’s Wireless LCD/Panda Keypad

Configuration Software

Allocating the Installer’s LCD/Panda Keypad & Defining the System

Language

Although an installer can use a customer’s wireless LCD/Panda keypad, RISCO Group offers
the Agility 4 installer a temporary “installer” wireless LCD/Panda keypad to be used for fully
configuring the system. This LCD/Panda keypad will be allocated temporarily, and not as a
permanent part of the system. After temporarily allocating the LCD/Panda keypad, the other
system devices can then be allocated with it, and the system further configured.
When the temporary installer LCD/Panda keypad is allocated, it prompts the installer to
define a default system language.

NOTE: An hour after exiting the programming mode, the installer LCD/Panda keypad will
be erased from the system’s memory (also when power is lost to the system).

To (temporarily) allocate the installer keypad and define the system language:

1. After the main panel is connected to the power supply, short press the main panel
button; the status is announced at the panel.

Note: If the keypad lapses into sleep-mode before you have chosen the language, restore
the choose-system-language display through simultaneously pressing [*] and [9])

2. With battery installed, press the keypad’s / buttons simultaneously

during the status announcement until the following message appears: Grand Master
Code:

3. Enter the Grand Master code (default is 1234) and then press / ; you are

Page 30
 now in the User Menu.

NOTE: When a wrong Grand Master code is entered, the keypad will not be allocated.
To continue this procedure, start the keypad allocation procedure again.

4. Press / twice to exit the User Menu, and enter the system again using the
installer code (default is 0132).

5. Now that you have temporarily allocated this “installer” LCD/Panda Keypad to the
system, you can now allocate other system devices. See Wireless Device Allocation, page 32.

Allocating the Customer’s LCD/Panda Keypad & Setting the Default

Language
Agility 4 can be fully configured via the customer’s wireless LCD/Panda keypad.
New systems require that the LCD/Panda keypad be the first device to be allocated to the
system, from which it then prompts the installer to define a default language. After the
LCD/Panda keypad allocation, the other system devices can then be allocated with it, and
the system further configured:

To allocate the LCD/Panda keypad and define the system language:

1. After the main panel is connected to the power supply, press the button on the main
panel for 5 seconds. The unit beeps once and enters “Learn” mode. The LEDs light up
one after the other.

2. With battery installed, press the keypad’s / buttons on the keypad

simultaneously for at least 2 seconds until a generic device allocation message is
broadcast and also displayed on the keypad.

3. In the displayed language menu, select the default system language, and then press

/ .

NOTE: If the keypad lapses into sleep-mode before you have chosen the language,
restore the -system-language display by simultaneously pressing * and 9.

4. Now that you have allocated this LCD/Panda Keypad to the system, you can now
allocate other system devices with the LCD/Panda keypad. See Wireless Device
Allocation, page 32.

Page 31
Configuration Software

A software application that enables you to program the system from a computer. It offers
the following alternatives:
Working locally, through a portable computer connected to the system via cable
Working at a remote site, communicating with the system via a phone line, modem,
IP address or RISCO Cloud.
For further information on programming the Agility 4 system via the Configuration
software, refer to the Configuration Software manual.

Wireless Device Allocation

All wireless devices (detectors and accessories) must also be allocated (registered) to the
system. Allocations can be performed via:
 Main panel: Quick allocation of all devices is performed by sending a RF signal
transmission from each device. Zones are automatically (and sequentially) assigned.
 LCD/Panda keypad (the following methods are available):

For having zones assigned automatically (and sequentially): You can either
perform by the “RF Allocation” method, or by entering each device’s unique
11-digit code (serial number) into the system.
For manually selecting a specific zone number to which a device is then
allocated: You can perform this by the “Zone Allocation” method.

 Configuration Software

NOTE: Regardless of the allocation method used, make sure to first install the batteries in
all devices before performing the allocation procedure.

Quick Allocation of all Devices at the Main Panel

You can quickly allocate all system devices (including keypads) at the main panel.

To perform quick device allocation at the main panel:

NOTE: To enable Quick Allocation mode the System bit "Quick Learn" should be enabled
(default).

1. Long-press the main panel button; each LED on the main panel will light up, one after
another, indicating the system is in “Learn mode.”

NOTE: The panel will sound each time you enter or exit the Learn mode.

2. Make sure batteries are installed in each device before allocating. For detectors, also

Page 32
 make sure the covers are removed so the tamper switches are accessible.
3. Send a signal transmission from each device per the chart below (if a device is not
listed on the chart, refer to the device’s specific instructions); the main panel beeps
once to accept or three times to reject. Once accepted the system announces the device
type and its assignment (for example, “Detector, zone 1”). Each device receives an
index number from the system, and zones are assigned automatically (and
sequentially, in the order allocated).

NOTE: For future use, it is recommended to write down the device assignment / zone
and installation location of each allocated device.

Table of Device Transmissions

Wireless device Transmission procedure

2-Way Panda Keypad

Press and simultaneously for at least 2 seconds

2-Way LCD Keypad

Press and simultaneously for at least 2 seconds

2-Way Slim Keypad

Press and simultaneously for at least 2 seconds.
PIR Detectors:
 PIR
 PIR camera
 PIR-pet
Press the tamper switch for 3 seconds.
 PIR-pet camera
NOTE: See PIR Camera
Setup, page 39.
Curtain detector After inserting battery, close the bracket and wait 3 seconds.
1-Way Magnetic
Press the tamper switch for 3 seconds.
Contact Detectors
Press the tamper switch for 3 seconds.
2-Way Magnetic NOTE: After programming parameters for this device and exiting
Contact Detectors Programming mode, press the Tamper switch for 3 seconds, and then
wait 1 minute for the main panel to download the parameters from the
detector
2-Way Remote Control
Press and simultaneously for at least 2 seconds

1-Way Keyfob Click  for at least 2 seconds

After inserting battery, transmission is send automatically within 10
Smoke Detector
seconds.

Page 33
 Press the reset switch on the siren. After a squawk sounds, you have 10
Siren
seconds to press on the tamper switch for at least 3 seconds.
1. Set the Agility 4 system to Learn mode.
I/O Module
2. Send a WRITE message within 15 seconds after I/O module power up,
by pressing the Wall and Cover tampers switches simultaneously for
at least 3 seconds (when the PCB IS installed ONLY the cover tamper
has to be pressed).
2-Button Panic Keyfob
Press both buttons for at least 7 seconds
Wrist Band Panic
Press the button for at least 7 seconds.
Transmitter

4. When all the devices have been enrolled, short-press the main panel button to exit
Learn mode; the unit beeps once and the LEDs stop flashing.

Device Allocation using the Wireless LCD/Panda Keypad

RF Allocation Method

Using the RF Allocation method, zones are assigned automatically and sequentially.

To perform device allocation by RF Allocation:

1. Go to the Installer menu and select Programming  Radio Device  Allocation 

1) RF Allocation. The system immediately goes into Learn mode.

2. Send a transmission from the device. (See Table of Device Transmissions, page 33).

3. The main panel will acknowledge the transmission with a beep and LCD/Panda
keypad displays the device's automatically-assigned zone and index numbers, the
device’s
11-digit serial number, and the device’s description.

4. When finished allocating the system device(s), press / repeatedly until you

arrive back to Radio Device, then press to Exit, and / to confirm.

Serial Number Method

When performing allocation by entering the device’s serial number (“code”), zones are
assigned automatically and sequentially.

To perform device allocation by serial number:

1. Go to the Installer menu and select Programming  Radio Device  Allocation 

2) By Code.

Page 34
2. Enter the device’s 11 digit serial number (“code”), and then press / .

3. The main panel will acknowledge the transmission with a beep and the LCD/Panda
keypad displays the device's automatically-assigned zone and index numbers, the
device’s 11-digit serial number, and the device’s description.

4. When finished allocating the system device(s), press / repeatedly until you

arrive back to Radio Device, then press to Exit, and / to confirm.

Zone Allocation Method

When performing allocation by the Zone Allocation method, you manually select a specific
zone / index number to which the device is then allocated.

To allocate devices with zones manually-specified:

1. From the Installer menus select: Programming > Radio Device > Allocation >
3) Zone Allocation.

2. Using / to scroll between the 2 digits of the zone number, enter

the zone number of your choice (from 01 –32), and then press / .

3. Now use / to select the allocation method (RF Allocation or Serial

Number method) and then perform the respective zone allocation procedure (per RF
Allocation or Serial Number procedures listed above); the main panel will
acknowledge the transmission with a beep and the LCD/Panda keypad displays your
manually-assigned zone and index numbers, the device’s 11-digit serial number, and
the device’s description.

Allocating Devices using the Configuration Software

Perform wireless device allocation via the Configuration Software in two different ways:
RF Allocation or by entering the device’s code (serial number).

To perform RF device allocation from the Configuration Software

1. Establish Communication between the main panel and the Configuration software.
(For more information, refer to the Configuration Software Manual)

2. Open the Activities > Radio Device Allocation screen.

Page 35
3. Click . This operation will set the main panel to Learn mode. The following
message appears:

4. Send a transmission from the device (see Table of Device Transmissions, page 33).

5. The main panel will acknowledge the transmission with a sound. When the system
recognizes the device the Radio Device Allocation screen indicates that the status of
allocation has been successful. The serial number, accessory type and the index
number information will be displayed. The index number is automatically assigned by
the system.

NOTE: If required you can change the index number of the wireless device by
selecting the required index number and clicking again.

6. To allocate another wireless device click and then repeat from step 2.

To perform device allocation by serial number from the Configuration Software

1. Establish Communication between the main panel and the Configuration software by
selecting Communication > Connect from the main menu. (For more information,
refer to the Configuration Software Manual)

2. Open the Radio Device Allocation screen. In the Allocation area, enter the device's
serial number.

NOTE: The serial number can be found on the device.

3. Select the wireless device index number. Automatic means that the index number is
automatically addressed by the system,

4. Click the button.

5. The main panel will acknowledge the transmission with a sound. When the system
recognizes the device the Radio Device Allocation screen indicates that the status of
allocation has been successful.

Page 36
Deleting Devices
Deleting wireless device allocations can be done from the LCD/Panda keypad or from the
Configuration Software. Deleting can be done for all devices simultaneously, or for a single
device.

Deleting all Devices Simultaneously from the LCD/Panda Keypad

To delete all devices simultaneously from the wireless LCD/Panda keypad:
1. Go to the Installer menus and select Programming  1)System  5) Settings 

2)Erase WL  / .

2. Press / to confirm the deletion.

Deleting a Single Device from the LCD/Panda Keypad

To delete a single device allocation from the wireless LCD/Panda keypad:

1. Go to Installer menus and select Programming  Radio Device  4) Delete 

/ .

2. Use / to scroll to the device category, and press / .

3. Enter (or scroll to) the device to delete, and then press / .

4. Press / again to confirm the deletion.

5. Press / to go back and delete additional devices (and repeat this procedure)
as needed.

NOTE: If you enter all zeros (00000000000) in place of the device’s 11-digit serial
number (for example at Programming Radio Device  ModificationParameters)
this will also delete the device allocation.

Deleting all Devices Simultaneously from the Configuration Software

To delete all device allocations from the Configuration Software:

1. Establish Communication between the main panel and the Configuration software by
selecting Communication>Connect from the main menu. (For more information, refer
to the Configuration Software Manual).

2. In the Radio Device Allocation screen in the Delete Accessories area, click the Delete
All button. When all accessories have been deleted the screen will indicate that

Page 37
 deletion has been successful.

Deleting a Single Device from the Configuration Software

To delete a single device allocation from the Configuration software:

1. Establish Communication between the main unit and the Configuration software (For
more information, refer to the Configuration Software Manual).

2. In the Radio Device Allocation screen in the Delete Accessories area enter the device's
serial code and click the Delete button.

Establishing Communication to the RISCO Cloud

Agility 4 can be configured to be constantly connected to the RISCO Cloud, an application
server that handles all communication between the system, service providers and
Smartphone/Web users. The Cloud enables remote monitoring and control of the system,
sending event notifications, and viewing real-time video clips via VUpoint IP cameras – for
both monitoring stations and system users.

Step 1: Enabling Cloud Communication

 From the Programming menu select: 1) System > 2) Controls >

3) Communication > Cloud Enable > toggle to [Y] using / , and then

press / to confirm.

Step 2: Defining the (GPRS or IP) Communication Channel

Connecting with GPRS
1. From Programming menu select : 4)Communication > 1)Method > 2)GSM > 2)GPRS

2. Use / to scroll between 1)APN Code and 2)APN User Name and
then define the APN code and user name respectively. This information must
correspond with that supplied by the SIM card service provider.
Connecting with IP

3. From Programming menu select: 4)Communication > 1)Method > 3)IP > 1)IP Config
4. Now define whether the system’s IP address is Static or Dynamic. If Dynamic select
[Y] (the system refers to an IP address provided by the DHCP). If Static select [N] and
define all other parameters in the menu.

Step 3: Defining Cloud Parameters for IP or GSM/GPRS

From the Installer menu Programming select: 4) Communication > 5) Cloud, and then
define the following parameters:

Page 38
1. IP Address: The server IP address (www.riscocloud.com, or that of your
organization's Cloud server)
2. IP Port: The server port is set to 33000.
3. Password: The password for server access as provided by your provider (if required).
This password should be identical to the main panel password as defined in the server
under the Main Panel page definition (AAAAAA by default).
4. Channel: Select the communication path for the Cloud (based on IP or GPRS
communication) as appears in the available options.

NOTE: The SIM card must be installed (see Installing the SIM Card, page 27).

5. Controls: The Agility 4 supports parallel channel reporting (via PSTN, IP, GPRS SMS, or
voice) to both the monitoring station and Follow Me users. Use this setting to decide if the
panel reports events to the monitoring station or Follow Me in parallel to the report to the
Cloud (assuming there is an additional communication channel available – PSTN, IP,
GPRS SMS, or voice), or only as a backup when the communication between the Agility 4
and the Cloud is not functioning.

Step 4: Registering the Agility 4 to the RISCO Cloud

Registering with the RISCO Cloud enables the user to monitor, control and configure the
Agility 4 system from any location.
The Agility 4 panel must be connected to the Internet via the network cable or via wireless
connection. The panel will then automatically register itself to the RISCO Cloud. The
Installer can then associate the panel with a company or assign a site to a company in the
RISCO Cloud. (For further details and instructions, refer to the RISCO Cloud Installer Quick
Guide).

iRISCO Smartphone App

The iRISCO Smartphone app provides smart and easy control of the Agility 4 system,
enabling on-the-go users to receive event notifications, view the system status and event
history, arm/disarm the system, activate home automation devices, bypass zones, and
utilize IP cameras for visual verification and self-monitoring.
iRISCO is available for iOS and Android

PIR Camera Setup

PIR-based camera detectors perform detection with advanced still image and video
recording capabilities. Up to eight PIR detectors / cameras can be used in the Agility 4
system.

For the physical installation of the PIRs, refer to the product instructions.

Page 39
To set up PIR camera detectors:

1. Allocate the PIR camera as any other detector (see prior allocation procedures)

2. Set the PIR camera parameters as they appear under the Advanced Zone parameters
per product instructions.

3. Set communication between the Agility 4 and the Cloud server (See Establishing
Communication to the RISCO Cloud, page 38).

4. Log in to the Web User Application (www.riscocloud.com), then go to the main

display and select the Video option.

5. Adjust the PIR camera view as follows:

a. Select camera.
b. Perform a snapshot from the server.
c. Go to the History tab.
d. Click on the required picture.

6. As necessary, adjust the PIR camera and repeat steps b—d.

Page 40
Chapter 4 Installer Menus
The following chapter describes the parameters and programming options of the system
that are installer-programmed via a wireless LCD/Panda keypad or Configuration
Software.

Describing the Wireless LCD/Panda Keypad

The wireless LCD/Panda keypad contains three LED indicators, LCD/Panda display and
numerical buttons.

Button Button
(LCD (Panda Primary function
Keypad) Keypad)

To “wake-up” the keypad, go back one level, exit menus

(similar to the Esc key)

To select, confirm, “OK” (similar to the Enter key)

To scroll

To toggle between options (such as Y / N)

To exit the programming mode (followed by / to

confirm)

NOTE: During installer programming, the keypad will turn off after 4 minutes if no entry
has been made to the keys. Press any button to restore the keypad. It will display the last
parameter you were working on.

Accessing the Installer Menus

To access the installer menus via the wireless LCD keypad:

1. Click / to activate the LCD/Panda keypad.

1. Enter the installer code (0132 is the default).

Page 41
 NOTE: If the Authorize Installer system bit is defined as YES, a Grand Master code is
required to authorize the installer to enter the programming mode. In this case the
Grand Master code should be entered after the installer code via the Grand Master
menu  Activities Authorize Installer.

2. Use / to scroll through all the main installer menus:

1) Programming
2) Testing
3) Activities
4) Follow Me
5) Clock
6) Event Log
7) Macro

3. Press / to select a main installer menu.

4. Use / to scroll through the list of all sub-menus.

Programming Menu
After selecting the Programming Menu, you can scroll between the following list of its
sub-menus:

1. System
2. Radio Devices
3. Codes
4. Communication
5. Audio
0. Exit

1. System Sub-Menu
The System sub-menu has the following items:

1. Timers
2. Controls
3. Labels
4. Sounds
5. Settings
6. Service Information
7. Firmware Update

Page 42
8. Picture Server

1.1 Timers
The Timers menu contains parameters that specify the duration of an action.
System: Timers
Parameter Default Range
Exit/Entry Delay 1
The amount of time before the system is armed/disarmed. Usually used at front entrance
door.
Entry Delay 1 30 sec 0-255 sec
Duration of entry delay 1 before the system is disarmed
Exit Delay 1 45 sec 0-255 sec
Duration of exit delay 1 before the system is armed
Exit/Entry Delay 2
The amount of time before the system is armed/disarmed. Usually used at the back door.
Entry Delay 2 45 sec 0-255 sec
Duration of entry delay 2 before the system is disarmed
Exit Delay 2 60 sec 0-255 sec
Duration of exit delay 2 before the system is armed
Bell Timeout 04 min 01-90 min
Duration of the siren during alarm.
Bell Delay 00 min 00-90 min
The time delay before a siren sound is produced after triggering an alarm.
AC Off Delay 30 min 0-255 min
In the case of a loss of AC power, this parameter specifies the delay period before
reporting the event or operating the Programmable Output. If the delay time is set to
zero, there will be no delay period.
Jamming Time None None, 10, 20 or 30 sec
Specifies the period of time that the system's receiver tolerates unwanted radio
frequencies capable of blocking (jamming) signals produced by the system's transmitters.
Once the specified time is reached, the system sends a report code to the monitoring
station or activates a local siren, depending on the Audible Jamming system control.
NONE: No jamming will be detected or reported.

Page 43
System: Timers
Parameter Default Range
RX Supervision 0 hours 0-7 hours
Specifies how often the system expects to get a signal from the system's transmitters. If a
signal from a zone is not received during the specified time the zone will be regarded as
lost, the system will send a report code to the monitoring station, and the system status
will be "Not Ready".
Notes: 0 hours disables supervision
It is recommended to set the supervision time to a minimum of 3 hours

TX Supervision 058 0-255 min

Specifies how often a bi-directional wireless device generates a supervision request to the
system.
If any of the accessories does not respond to the request, at least once, during the RX
Supervision time, the system will regard the accessory as Lost.
Note: The device will generate the supervision message according to the time defined.

Important: The RX Supervision time should be higher than the Tx Supervision time in order to eliminate
false lost event.
Redial Wait 30 sec 0-255 sec
The number of seconds between attempts at redialing the same phone number.
Applies to both the MS Retries and FM Retries parameters.
Note: Used for both PSTN and GSM.

More
Swinger Limit Shutdown 00 0-15 times
A swinger is a repeated violation of the same zone, often resulting in a nuisance alarm
and usually due to a malfunction, an environmental problem, or the incorrect
installation of a detector or sensor.
This parameter specifies the number of violations of the same zone reported during a
single armed period, before the zone is automatically bypassed.
Note: 00 to disables the swinger shutdown

No activity 00 0-99 hours

Determines the time limit for reception of signals from sensors used to monitor the
activity of sick, elderly or disabled people. If no signal is received from a zone defined
with the "No Activity" feature at least once within the defined time limit, a “no-
activity” alert can be send to Follow Me destination, a local message can be heard and a
report to Monitoring Station can be defined to be send.
Options: 0 =this parameter is inactive.

Page 44
System: Timers
Parameter Default Range
Last Exit Sound 00 0-255 seconds
Defines the last seconds of the Exit Time that the beep sound will change (main unit
and keypads), indicating to the user that Exit Time is about to end.
Entry Bypass 30 seconds (15–240)
When the 2-Way Wireless Slim Keypad Reader is defined as Bypass mode, this timer
defines the period during which an Open Delay zone type (typically door) can be
opened without triggering an alarm event.
Service Time 20 minutes 1-240 minutes
The time period that all tampers (main unit and accessories) can be opened for
purposes of battery replacement without triggering a tamper alarm (see Service Mode,
page 134).

1.2 Controls

The Control menu contains parameters that control specific system operations.
System: Controls
Parameter Default
Basic programming
Quick Arm YES
YES: Eliminates the need for a user code when arming (Full or partial) the system by a
keypad or 2-way remote control.
NO: A valid user code is required for arming using a keypad or remote control.
Allow Bypass YES
YES: Permits zone bypassing by authorized system users after entering a valid user code.
NO: Zone bypassing is NOT permitted.
Quick Status YES
YES: A user code is not required before pressing the status key/button on your wireless
keypad or bi-directional remote control.
NO: A user code is required to activate the status key.
False Code Trouble YES
YES: A false code report is sent to the monitoring station after five successive attempts at
arming or disarming in which an incorrect user code is entered. No alarm sounds at the
premises, but a trouble indication appears. The wireless keypad will be locked for 30
minutes.
NO: A local alarm is sounded at the premises.

Page 45
System: Controls
Parameter Default
Siren Squawk YES
YES: Arming or disarming the system using a remote control, wireless keypad or a key-
switch produces a brief "chirp" and activates the strobe as follows:
 One chirp indicates the system is armed (also when arming with a keypad).
 Two chirps indicate the system is disarmed.
 Four chirps indicate the system is disarmed after an alarm.
NO: No "chirp" is produced.
Audible Panic NO
YES: The sirens operate when a "Police Alarm" is initiated at the keypad (if defined), the
remote control or when a panic zone is activated.
NO: No siren operation occurs during a Panic Alarm, making the alarm silent at the
protected site.
Note: The system always transmits a panic report to the monitoring station.

Buzzer  Bell NO
YES: If an alarm occurs when the system is armed in the Stay Arm mode, a buzzer
sounds for 15 seconds before the sirens operate.
NO: An alarm in the Stay Arm mode causes sirens to operate simultaneously.
Audible Jamming NO
Relates to the Jamming Time parameter.
YES: Once the specified time is reached, the system activates the siren and sends a report
code to the monitoring station.
NO: Once the specified time is reached the sirens do not operate.
Exit Stay Beeps YES
Determines whether the system will sound beeps during exit time in Stay Arming.
YES: Exit beeps will sound
NO: Exit beeps will not sound
Forced Arming YES
YES: Arming a partition, using a Slim keypad (from ver. 3.84L), remote control, or
key-switch can be performed with violated (not ready) zones in the system. Any
violated (not ready) zone(s) in the partition will be bypassed automatically. The partition
is then "force armed," and all intact zones are capable of producing an alarm.
NO: The partition cannot be armed until all violated (not ready) zones are secured.

Page 46
System: Controls
Parameter Default
Arm Pre-warning YES
Related to auto Arm/Disarm operation.
YES: For any partition(s) set up for Auto Arming, an audible Exit Delay (warning)
countdown will commence 4.25 minutes prior to the automatic Arming. During this
period, Exit Delay beeps will be heard.
You can enter a valid user code at any time during the countdown to delay the partition's
automatic Arming by 45 minutes.
When an "Auto-Arm" partition is disarmed, as described above, it can no longer be
automatically armed during the current day.
The extended 4.25 minutes warning does not apply to automatic Partial Arming.
NO: Auto Arming for any programmed partition(s) takes place at the designated time.
The programmed Exit Delay period and any audible signal occur as expected.
Default Enable YES
This option contains parameters that relate to what happens to the Installer, Sub-Installer
and Grand Master codes if the main panel’s DEFAULT DIP switch 3 is in place when
power to the main panel is switched off and then on. For more information regarding
main panel defaults refer to DIP Switch Setting, page 24.
Note: The Default Enable parameter’s state is not reset upon performing system default.

YES: The Installer, Sub-Installer and Grand Master codes will return to the original,
factory default values.
NO: The Installer, Sub-Installer and Grand Master codes will NOT return to the original,
factory default values by an unauthorized user.
Main Button: Status-Y/Talk-N YES
The Agility 4 enables the MS to perform Listen-In and Talk functions in order to verify a
cause of event or to guide someone in distress. The Main Button: Status-Y/Talk-N
parameter determines the function of the button on the surface of the main unit to enable
Listen-In and Talk.
YES: Status button – The system will relay the system status.
NO: Service call button – The system dials the monitoring station to establish 2-way
communication.
Quick Learn YES
Enables the button on the surface of the main unit to perform quick allocation of wireless
devices. (See Quick Allocation of all Devices at the , page 32).
YES: Quick learn mode is enabled. Long press on the main unit button will start Learn
mode. The LEDs on the main unit will start flashing one after the other
NO: Quick learning mode is disabled. The main unit button is not in Learn mode.

Page 47
System: Controls
Parameter Default
Advanced programming
Area NO
Changes the system operation to Area instead of Partition, which then changes only the
operation of a common zone.
YES: When selected, the following points are relevant:
 A common zone will be armed after any partition is armed.
 A common zone will be disarmed only when all partitions are disarmed.
NO: When selected, the following points are relevant:
 A common zone will be armed only when all partitions are armed.
 A common zone will be disarmed when any partition is disarmed.
Global Follower NO
YES: Specifies that all zones (that are programmed to follow an Exit/Entry Delay time)
will follow the Exit/Entry Delay time of any armed partition.
NO: Specifies that all zones (that are programmed to follow an Entry Delay time) will
follow the Entry Delay time of only the partitions to which they are assigned.
Summer/Winter NO
YES: The system automatically sets its time of day clock one hour ahead in the spring (on
the last Sunday in March) and one hour back in the Autumn (on the last Sunday in
October).
NO: No automatic time accommodation is made.
24 Hour Bypass NO
YES: It is possible for the user to bypass a 24-hour zone.
Note: When set, this parameter also applies to the zone’s associated tamper settings. Thus, bypassing a
zone, also bypasses its tamper.

NO: It is not possible for the user to bypass a 24-hour zone.

Technician Tamper NO
YES: It is necessary to enter the installer code to reset a tamper alarm. Therefore, resetting
a tamper alarm requires the intervention of the alarm company. However, the system can
still be set.
NO: Correcting the problem resets a tamper alarm, requiring no alarm company help.

Page 48
System: Controls
Parameter Default
Technician Reset NO
YES: It is necessary to enter the installer code to reset an alarmed partition after it has
been disarmed. This requires the intervention of the alarm company.
Note: Before the Ready LED can light all zones within the partition must be secured.

NO: Once an alarmed partition is reset the Ready LED lights when all zones are secured.
Installer Tamper NO
YES: After a tamper alarm, the system is not ready to arm. This requires the intervention
of the alarm company.
NO: After a tamper alarm is restored the system is ready.
Low Battery Arm YES
YES: Allows arming of the system when a low battery condition is detected in the main
unit.
NO: Arming the system is disabled when a low battery condition is detected.
Siren Pre-Alarm NO
Specifies if the system will send a pre-alarm message to the siren while an entry delay
starts.
YES: The system sends a pre-alarm signal to the siren at the beginning of the entry delay.
If the siren does not receive a cancellation signal from the system at the end of the entry
time, the siren goes into alarm.
NO: Pre-Alarm disabled
Bell 30/10 NO
YES: The sirens cease to sound for 10 seconds after each 30 seconds of operation.
NO: The sirens operate without interruption.
Fire Pattern NO
YES: During a fire alarm, the sirens produce a pattern of 3 short bursts followed by a
brief pause.
NO: During a fire alarm, the flow of sounds produced by the siren is a pattern of 2
seconds ON, then 2 seconds OFF.

Page 49
System: Controls
Parameter Default
IMQ NO
YES: Causes the following parameters to function as follows:
o Auto Arm Bypass: If there is an open zone during the Auto Arm process, the system
will be armed, and a silent alarm will be activated (unless the open zone is closed).
o A utility output defined as “Auto Arm Alarm” is activated.
o A utility output defined as “Zone Loss Alarm” is activated
NO: Causes the following parameters to function as follows:
o Auto Arm Bypass: If the Auto Arm programming arms the system and there is an open
zone during the auto arm, the system will bypass the open zones and arm the system.
o A utility output defined as “Auto Arm Alarm” is deactivated.
o A utility output defined as “Zone Loss Alarm” is deactivated.
Disable Incoming Call NO
Used to disable all incoming calls trying to come in via the voice channel (PSTN or GSM).
YES: Incoming calls from voice channel are disabled.
NO: Incoming calls from voice channel are enabled.
Note: Incoming data call via the GSM data channel is still enabled.

Bypass Unique Code YES YES/NO

YES: Unique code for the purpose of the door bypass feature. The codes used for the door
bypass feature are defined with door bypass authority level
NO: The regular user code can be used as a bypass code (Not including Arm only
authority level). The same user codes will be used from a bypass keypad and from a
regular keypad
Silent Remote Install NO
YES: During Configuration Software programming and during remote software update
all panel sounds are suppressed.
NO: The panel generates sounds during programming by Configuration Software.
AntiMask=Tamper NO
Used to determine the operation of anti-masking detection in a bus zone.
YES: Anti mask violation will activate tamper alarm.
NO: Anti mask violation will be regarded as trouble event.
Power Management NO
YES: In case of a power failure, the system will disable the IP Module to save battery life.
NO: Does not extend battery life in case of a power failure.

Note: This option functions only with Multi-Socket IP.

Page 50
System: Controls
Parameter Default
Presence Log NO
YES: Presence will be recorded in the event log.
NO: Presence will not be recorded in the event log.
Secondary Alarm NO
YES: If smoke or heat is detected by one of the Smoke, Heat and PIR detectors in the
system, the other Smoke, Heat and PIR detectors in the system will sound their sirens.
NO: If smoke or heat is detected by one of the Smoke, Heat and PIR detectors in the
system, the other Smoke, Heat and PIR detectors in the system will not sound their sirens.
Note: This option applies only to the RWX35SP Smoke, Heat and PIR detector.
Communication Controls
MS Enable YES

Use / to toggle between Y (yes) and N (no) to define whether there will be
communication to the monitoring station.
YES: Enables communication with the monitoring station to report alarms, trouble, and
supervisory events.
NO: No communication with the monitoring station is possible. Choose NO for
installations that are NOT monitored by a monitoring station.
Configuration Software Enable YES
YES: Enables communication between the alarm company and the system using the
Configuration software. This enables modifying an installation's configuration, obtaining
status information, and issuing main panel commands, all from a remote location.
NO: Disables communication, as detailed above.
FM Enable YES
YES: Enables Follow-Me communication.
If both the MS phones and the FM phones are defined, the system will first call the MS
phones and then the FM phones.
NO: Disables Follow-Me communication.
Cloud Enable NO
Yes: Enables communication between the Agility 4 system and the RISCO Cloud server.
NO: Does not enable communication, as detailed above.
EN 50131 programming
Authorize Installer NO

Page 51
System: Controls
Parameter Default
This option limits the Installer and Sub-installer authorization to access the
programming menu.
YES: A Grand Master code is required to authorize the installer to enter the
programming mode for 1 hour.
NO: The Installer does not need an authorization code.
Override Trouble YES
Specifies if the system/partition can be armed when there is a fault in the system.
YES: The system will arm even if there is a fault in the system.
NO: When the user starts the arming process and there is a system-fault, the user must
confirm that he is aware of all faults before continuing with the Arming process.
This is done via the User menuActivitiesBypass Trouble.
The system will not arm during forced arming if a fault occurred in the system
Restore Alarm NO
YES: The user must confirm that he is aware that alarm occurred in the system before
rearming the system. The system will be in "Not Ready" status until he confirms the
alarm. This is done via the User menuActivitiesAdvancedRestore Alarm.
NO: The user does not need to confirm the alarm before rearming the system.
Mandatory Event Log NO
YES: Only mandatory events (specified in the EN standard) will be displayed in the
Event Log.
NO: All the events will be displayed in the Event Log.
Restore Troubles NO
YES: The user must manually confirm the restoral of each trouble to a normal condition.
This is done via the User menu  Activities  Advanced  Restore Troubles.
NO: The restoral report of each trouble is automatic .
Exit Alarm YES
YES: A violated zone outside the exit route will generate an alarm during the exit time. A
report to the monitoring station for arming the system is sent at the beginning of the
arming procedure.
NO: A violated zone outside the exit route will cancel the arming process. A report to the
monitoring station is send at the end of a successful arming procedure.
Entry Alarm NO

Page 52
System: Controls
Parameter Default
This feature is used to reduce false alarm reports to the MS.
YES: The report to the MS and the siren alarm will be delayed for 30 seconds or until the
end of the predefined entry delay (the shorter time of the two) following a violation of a
zone outside the entry route.
NO: A violated zone outside the entry route will generate an alarm during the
entry time and a report will be sent to the MS.
20 Minutes Signal NO
YES: Prior to arming the system, the system will check for zones that did not send a
signal for more than 20 minutes. These zones will be regarded as not ready. A partition
assigned with a not ready zone cannot be armed.
NO: Prior to arming, the system will not check whether a zone did not send a signal for
more than 20 minutes.
Attenuation NO
YES: The Agility 4 receiver will be attenuated by 6 dB during the communication test.
NO: The Agility 4 receiver works in normal operation mode.
PD6662 programming
Bypass Exit/Entry YES
YES: It is possible for the user to bypass an Exit/Entry zone.
NO: An Exit/Entry zone cannot be bypassed.
Entry Disable NO
YES: The alarm confirmation process will be disabled when the entry time starts.
NO: The alarm confirmation process will start when the entry time starts.
Route Disable NO
YES: The panel disables the entry route zones (EX/EN, EX (OP)/EN, followers and Final
Exit) from participating in the alarm confirmation process when the entry time starts.
Note: Sequential confirmation can still be established from two confirmed zones, located off the entry route.

NO: The entry route zones will participate in the alarm confirmation process when the
entry time starts.
Installer Confirmation NO
YES: An installer reset confirmation is required in order to reset the system after a
confirmed alarm. The system cannot be armed until an Installer Reset Confirmation is
performed. The reset can be done by entering the Anti code or entering the installation
mode or by performing an “installer reset” from the keypad.
NO: Any means can be used to arm or disarm (keypad, remote phone operation etc.).

Page 53
System: Controls
Parameter Default
Key Switch Lock NO
YES: Only a latched key switch zone can arm or disarm the system.
Note: When the system has more than 1 zone defined as latch key switch, the arm/disarm operation will
occur only after all these zones are armed or disarmed.

NO: Any means can be used to arm or disarm (keypad, remote phone operation etc.).
Entry Disarm NO
Determines if the system’s disarming depends on the entry time.
YES: A remote control or keypad proximity tag can disarm the system during the entry
time.
Note: The system cannot be disarmed with a remote control while the system is armed.
This parameter setting is relevant only for the Away Arm state and not for Stay Arm.

NO: The system can be disarmed during any time using any disarming device.
CP-01 programming
Exit Restart NO
Used to define if an exit time shall restart one additional time while an entry/exit zone is
tripped twice during exit time.
YES: Exit time will restart for one time only when an entry/exit zone is tripped during
exit time.
NO: Exit time will not be affected if an entry/exit zone is tripped during exit time.
Auto Stay NO
Used to define the system's arming mode when using a keypad and no exit/entry zone
is tripped during exit mode.
YES: If no exit/entry zone is tripped during exit time the system will be armed in STAY
mode.
NO: If no exit/entry zone is tripped during exit time the system will be armed in Away
mode.

Page 54
System: Controls
Parameter Default
Exit Error NO
Used to define what will happen if an Exit/Entry zone is left open at the end of the exit
time.
YES:
o Local alarm will be activated at the end of the exit time.
o Exit error report will be sent to the monitoring station together with an alarm report
if the system has not been disarmed during the entry time that immediately started
after the exit time expiration.
NO:
o No local alarm will be activated at the end of the exit time.
o Only an alarm report will be sent to the monitoring station if the system has not been
disarmed during the entry time that immediately started after the exit time
expiration
3 Minute Bypass NO
YES: Bypasses all zones automatically for 3 minutes when power is restored to an
"unpowered" system.
NO: No bypassing occurs.

Page 55
1.3 Labels

You can rename the labels that identify the system and partitions by changing the default
labels (Partition 1, Partition 2 and so on) to, for example, The Jones's, Sales Dept, or
Mastr Bedr as appropriate.
Labels that can be renamed:
System: Labels
Parameter Default Range
System Security System Any 16 characters
Edits the global (system) label
Partition 1/2/3 Partitions 1 through 3 Any 16 characters
Edits partition labels
To rename labels using the keypad keys to produce characters:
Key Data Sequence
1 1 . , ' ? ! " – ( ) @ / : _ + & * #
2 2 a b c A B C
3 3 d e f D E F
4 4 g h i G H I
5 5 j k l J K L
6 6 m n o M N O
7 7 p q r s P Q R S
8 8 t u v T U V
9 9 w x y z W X Y Z
0 0
Use these keys to toggle forwards and backwards through all the
available characters.
/

Page 56
1.4 Sounds
The Sounds menu contains parameters that enable you to set the sound(s) that will be
produced by the system after the following system events:
System: Sounds
Parameter Default Range
Tamper Sound Bell+Buzzer 1 to 6
Sets the sound(s) produced by a Tamper violation according to the following options:
o Silent
o Bell (External/Internal siren)
o Buzzer (main unit)
o Bell + Buzzer
o Bell/A Buzzer/D: Bell when system armed, Buzzer when system disarmed
o Bell/A S/Disarm: Bell when system armed, Silence when system disarmed
Local Alarm Level 1 0-5, OFF
Sets the main unit's internal speaker Alarm volume. The volume ranges between 0 (silent)
to 5 (Max volume). After setting/changing the volume, sound will be emitted by the
internal speaker to enable evaluation of the selected volume level.
Local Squawk Level 1 0-5, OFF
Sets the main unit's internal speaker Squawk volume. The volume ranges between 0
(silent) to 5 (Max volume). After setting/changing the volume, sound will be emitted by
the internal speaker to enable evaluation of the selected volume level.
Exit/Entry Beeps Volume Level 1 0-5, OFF
Determines the volume of the beeps sounded from the main unit during the Exit/Entry
times.
Speaker Volume Level 1 0-4
Determines the volume of the messages sounded from the main unit or the Listen-In and
Talk unit.

Page 57
1.5 System Settings

System: Settings
Parameter Default Range
Default Panel
Restores programming options to factory defaults.
The Panel Default option will be followed by questions regarding the defaults of the labels

and erasing wireless devices. Use / to toggle your Y/N option.

Erase Wireless Device
Erase wireless devices without changing the system current programmed parameters.
Language
Sets the system language (Email, SMS and keypad language)
Standards
EN 50131 NO
Sets the panel programming options in compliance with EN standards. (See
Appendix F:).
PD6662 NO
Sets the panel programming options in compliance with PD6662 standards.
CP-01 NO
Sets the panel programming options in compliance with CP-01 standards.
Customer
Modify here the 3-character system Customer ID as per label format (See Labels, page 56).
Changing the Customer ID results in changing the system language and default settings
according to the predefined factory Customer ID settings. Use this setting to alter the
Customer ID specified upon first-time start-up for the Agility 4. Consult with your RISCO
representative to acquire the appropriate Customer ID.

1.6 Service Information

The Service Information menu enables you to insert information accessible to the system's
users of the alarm company from whom the service is obtained.
System: Service Information
Parameter Default Range
Name Any 16 characters
Enables you to insert and/or edit the name of the alarm company from whom service
may be obtained. The information can be viewed by the user using the wireless keypad.
Phone Any 16 characters
Enables you to insert and/or edit the service phone number. The information can be
viewed by the user using the wireless keypad

Page 58
1.7 Firmware Update

The Agility 4 enables you to remotely upgrade the main unit firmware versions via IP or
GPRS channels. Under the Firmware Update menu you need to define the location of the
upgrade file. The request to start the remote upgrade can be done from the wireless LCD
keypad or from the Agility 4 Configuration Software. For detailed information refer to the
Remote Software Upgrade instruction guide.
System: Firmware Update
Parameter Default Range
Server IP firmware.riscogroup.com
Enter the IP address/URL of the router/gateway where the upgrade file is located.
Server port 00080
Enter the port on the router/gateway where the upgrade file is located.
File Path /WirelessPanels/OEN/FAT.txt
Enter the upgrade file name. For example: /AgilityV4/0EN/cpcp.bin
Please contact Customer Support services for the file name parameters.

1.8 Picture Server

The Agility 4 enables you to define a server on which to store and access images captured
by system-related cameras. Use this feature for the http solution
System: Picture Server
Parameter Default Range
Server IP
Enter the IP address of the router/gateway of the server where the pictures are to be
located.
Server port 00000
Enter the port on the router/gateway of the server where the pictures are to be located.
File Path Agility
Enter the upgrade file name.
Please contact Customer Support services for the file name parameters.

Username
Enter user name (if required). The user name is provided the server administrator. The
system supports a user name field of up to 32 alphanumeric characters and symbols (!, &, ?
etc).

Page 59
System: Picture Server
Parameter Default Range
Password
Enter the password (up to 24 alphanumeric characters and symbols.) as provided the
server administrator (if required).
Image Channel
Choose here the image transmitting channel for the HTTP server, subject to the system’s
installed networks.

Note: This feature requires that the monitoring station receiver supports the SIA IP protocol.

The four options are:

o IP/GPRS: The panel checks for the availability of the IP network. During regular
operation mode images are transmitted using the IP network line. In the case of
trouble in the IP network, the images are routed through the GPRS network.
o GPRS/IP: The panel checks for the availability of the GPRS network. During regular
operation mode all image transmission are carried out using the GPRS. In the case of
trouble the images are routed through the IP network.
o IP Only: The images are transmitted through the IP network only.
o GPRS Only: The images are transmitted through the GPRS network only.

2. Programming: Radio Devices Menu

The Radio Devices menu provides access to sub-menus that are used for programming,
defining and editing each of the system's wireless devices. The Radio Devices menu is
divided into the following sub-menus:
1. Allocation
2. Modification
3. Identification
4. Delete

2.1 Allocation
Each wireless device must be identified to the system receiver before its parameters can be
configured. See Wireless Device Allocation, page 32 for further information on the allocation
procedures.

Page 60
2.2 Modification
The modification menu is used to change the values of the parameters configured by the
system for each wireless device. The modification menu is divided into the following
submenus:
1. Zones
2. Keyfobs (Remote Controls)
3. Keypads
4. Sirens
5. I/O Expanders

NOTE: This list varies according to the devices that have been allocated to the system.
Only devices that have been allocated can be configured or modified by the installer.

2.2.1 Zones

The Zones menu is divided into the following sub-menus:

Parameters
Alarm (Sequential) Confirmation
Soak Test
Cross Zones

Parameters
Note: The parameters displayed, vary according to the type of zones connected to the system.

Zones: Parameters
Parameter Default Range
Label Zone Any characters
01/02/03/
…

A label identifies the zone in the system. Up to 16 characters). Use /

to toggle between all the possible characters for each key:
Serial Number
The serial number of the zone. Each wireless device has its own unique serial number.
Entering 00000000000 will delete the zone’s allocation.

Partition
The partition (1 to 3) assignment for each zone.
Type
Each zone can be defined as one of the following types:
Not Used

Page 61
Zones: Parameters
Parameter Default Range
Disables a zone. All unused zones should be given this designation.
Exit/Entry 1
Used for Exit/Entry doors. Violated Exit/Entry zones do not cause an intrusion
alarm during the Exit/Entry Delay. If the zone is not secured by the end the
delay expires it will trigger an intrusion alarm.
To start an arming process, this zone should be secured. When system is armed,
this zone starts the entry delay time.
Exit/Entry 2
Same as above, except that the Exit/Entry 2 time period applies.
Exit(Op)/Entry 1
Used for an Exit/Entry door. This zone behaves as described in the Exit/Entry 1
parameter, shown above, except that, if faulted, the arming process is not
prevented. To avoid an intrusion alarm, it must be secured before the expiration
of the Exit Delay period.
Exit(Op)/Entry 2
Same as above, except that the Exit (Op)/Entry 2 time period applies.
Entry Follower
Usually assigned to motion detectors and to interior doors protecting the area
between the entry door and the system.
This zone(s) causes an immediate intrusion alarm when violated unless an
Exit/Entry zone was violated first. In this case, Entry Follower zone(s) will
remain bypassed until the end of the Entry Delay period.
Intruder (Instant)
Usually intended for non-exit/entry doors, window protection, shock detection,
and motion detectors.
Causes an immediate intrusion alarm if violated after the system is armed or
during the Exit Delay time period.
When Auto Arm and Pre-Warning are defined, the instant zone will be armed
at the end of the Pre-Warning time period.
Interior + Exit/Entry 1
Used for Exit/Entry doors, as follows:
 If the system is armed in the Away (Full Arm) mode, the zone(s)
provide a delay (specified by Exit/Entry 1) allowing entry into and exit
from an armed premises.
 If the system is armed in the Stay mode, the zone is bypassed.

Page 62
Zones: Parameters
Parameter Default Range
Interior + Exit/Entry 2
Same as the I + Exit/Entry 1 parameter, described above, but the Exit/Entry 2
time period is applicable.
Interior + Exit(Op)/Entry 1
Used for an exit/entry door that, for convenience, may be kept open when the
system is being armed, as follows:
 In Away (Full Arm) mode behaves as an Exit (Op)/Entry 1 zone.
 In Stay mode, the zone will be bypassed.
Interior + Exit(Op)/Entry 2
Same as the I + Exit (Op)/Entry 1 parameter, described above, but the Exit/Entry
2 time period is applicable.
Interior + Entry Follower
Generally used for motion detectors and/or interior doors (for example, foyer),
which would have to be violated after entry in order to disarm the system, as
follows:
 In Away (Full Arm) mode behaves as an Entry Follower zone.
 In Stay mode, the zone will be bypassed.
Interior + Intruder (Instant)
Usually intended for non-exit/entry doors, window protection, shock detection
and motion detectors.
 In Away (Full Arm) mode behaves as an Intruder (instant) zone.
 In Stay mode, the zone is bypassed.
Entry Follower + Stay
Assigned to motion detectors and to interior doors protecting the area between
the entry door and the keypad, as follows:
 In Away (Full Arm) mode behaves like an Entry Follower Zone.
 In Stay mode behaves like an Exit/Entry 1 zone.
24 Hours
Usually assigned to protect non-movable glass, fixed skylights, and cabinets
(possibly) for shock detection systems.
A violation of such a zone causes an instant intrusion alarm, regardless of the
system's state.

Page 63
Zones: Parameters
Parameter Default Range
Fire
For smoke or other types of fire detectors. This option can also be used for
manually triggered panic buttons or pull stations (if permitted), as follows:
If violated, it causes an immediate fire alarm, fire report to the monitoring
station.
Panic
Used for external panic buttons and wireless panic transmitters.
If violated, an immediate panic alarm is sounded (if the zone sound is not
defined as silent or Audible Panic system control is enabled), regardless of the
system's state and panic report is send to the monitoring station. An alarm
display will not appear on the keypads.
Special
For external auxiliary emergency alert buttons and wireless auxiliary
emergency transmitters.
If violated, an immediate auxiliary emergency alarm is sounded, regardless of
the system's state and report is sent to the monitoring station.
Tamper
For tamper detection. This zone operates the same as 24 hours zone, but it has a
special reporting code.
Note: For this zone type the zone sound is determined according to the Tamper Sound defined
under System  Sound  Tamper

Water (Flood)
For flood or other types of water detectors. This zone operates the same as 24
hours zone, but it has a special flood report code (see Appendix A:) .
Gas
For the gas (natural gas) leak detector. This zone operates the same as 24 hours
zone, but it has a special gas report code. (See Appendix A )
CO
For CO (Carbon Monoxide) gas detectors. This zone operates the same as 24
hours zone, but it has a special CO report code (see Appendix A:) .
High Temperature
For detector temperature (hot or cold). This zone operates the same as 24 hours
zone, but it has a special report code (see Appendix A:) .

Page 64
Zones: Parameters
Parameter Default Range
Low Temperature
For detector temperature (hot or cold). This zone operates the same as 24 hours
zone, but it has a special report code (see Appendix A:) .
Technical
This zone operates the same as 24 hours zone, its report code should be
manually set according to the relevant detector connected to the zone.
Final Exit
Zones of this type must be the last detector to be activated on exit or the first
detector to be activated on entry.
When arming the system, the related partition arms 10 seconds after this zone is
closed, or opened and then closed. After it is triggered once, the zone acts as an
exit (open)/entry 1 zone.
Exit Termination
This type of zone is used to avoid a false alarm by acting like an Exit (OP)/Entry
zone.
When triggered (after arming the system and closing the door or opening the
door, arming the system, and closing the door), the system's Exit Delay time
period will be shortened to 10 seconds.
When you re-open the door, the entry time restarts.
Note: Exit Termination requires allocation of at least one Exit/Entry zone type in the partition.

UO Trigger
For a device or zone, which if violated at any time triggers a previously
programmed Utility Output, capable of activating an external indicator, relay,
appliance, and so on.

Page 65
Zones: Parameters
Parameter Default Range
Day
Usually assigned to an infrequently used door, such as an emergency door or a
movable skylight. Used to alert the system user if a violation occurs during the
disarmed period (trouble by day; burglary at night), as follows:
 With the system armed (either Away or Stay), the zone acts as an
instant zone. A violation of this zone after the system is armed or
during the Exit Delay time period causes an immediate intrusion
alarm.
 With the system disarmed, a violation of this zone attempts to alert the
user by causing the (Trouble) LED to flash rapidly. This directs the
user to view the system's status.
Optionally, such a violation can be reported to the Monitoring Station as a Zone
Trouble.
Pulsed Key Switch
Connect an external momentary action key switch to any zone given this
designation. This zone will arm/disarm the partitions assigned to it.
Pulsed Key Switch Delayed
Used to apply the Exit/Entry Delay 1 parameter to the Pulsed Key Switch zone.
Latched Key Switch
Connect an external SPST latched (non-momentary) key switch follows:
 After arming one or more partitions using the key switch and then
disarming using the keypad, the related partitions will be disarmed. In
order to arm the partition using the key switch again, turn the key to
the disarm position and then to the arm position.
 If a key switch latch is assigned to more than one partition and one of
the partitions is armed by using the keypad (the key switch stays in the
disarm position), then:
- When changing the position of the key switch to the arm position, all
the disarmed partitions, which belong to this key switch, will be
armed.
- When turning the key switch to the disarm position, all the partitions
will be disarmed.
Latch Key Switch Delay
Used to apply the Exit/Entry Delay 1 parameter to the latched key switch zone.

Page 66
Zones: Parameters
Parameter Default Range
Key Box
(Designed for the Danish market) A keybox is defined as a physical container in
which to place the house keys. The Agility 4 keybox zone behaves as follows:
 Opening a key box zone (regardless of system arming status) sends a
message to the monitoring station and recorded in the event log.
 There will be no indication on the screen that this zone is open.
 Tampering a keybox causes a tamper alarm.
 If this zone is open, then the system can be armed.
Open Delay
Use this zone for a door when used with slim keypads defined as bypass mode.
This zone behaves as follows:
 If the system is armed and the zone is opened without bypass code
approval the zone acts as an instant zone.
 If the system is armed and the zone is opened during the Bypass Entry
Timer it acts as an exit/entry zone (see Entry Bypass, page 45).
 When the system is disarmed, this zone activates as an Exit (open) /Entry
zone.
Sound Bell+Buzzer
Contains parameters that enable you to program the sound produced when a system
zone triggers an alarm for the time defined under the Bell Time Out parameter.
Silent
Produces no sound
Bell
Activates the wireless sirens (internal or external) and alarm from the main unit
assigned to the partitions of the zone.
Buzzer (main unit)
Activates the internal buzzer on the main unit.
Bell + Buzzer
Activates the wireless sirens and siren on the main unit simultaneously.
Bell/Arm Buzzer/Disarm
In a case of alarm, the following occurs:
 In Away mode (Full Arm) the wireless siren will operate.
 In Disarm mode, only the buzzer on the main unit will operate.

Page 67
Zones: Parameters
Parameter Default Range
Advanced programming
Chime None
The Chime parameter is used as an audible indication to a zone violation while the
system is Disarmed. Define which sound occurs when violated:
Options:
 None
 Buzzer (Main unit)
 Chime Sound 1
 Chime Sound 2
 Chime Sound 3
 Zone message
Controls
Supervision YES YES/NO
Choose which zone will be supervised by the system receiver according to the
time defined under the timer RX Supervision (see RX Supervision, page 44).
Forced Arming NO YES/NO
This option enables or disables the use of forced arming for each of the system's
zones, as follows:
 If forced arming is enabled for a particular zone, it allows the system to be
armed even though this zone is faulty.
 When a zone(s) enabled for forced arming is faulted, the LED blinks
during the disarm period.
 After arming, all zones enabled for forced arming are bypassed at the end of
the Exit Delay time period.
 If a faulted zone (one enabled for force arming) is secured during the armed
period, it will no longer be bypassed and will be included among the system's
armed zones.
No Activity NO YES/NO
Determines whether the zone participates in the No Activity function. The No
Activity function is for reception of signals used to monitor the activity of sick,
elderly or disabled people (see No activity, page 44).
LED Enable Y/N (Only for 2 Way PIR and 2 Way WatchOUT) YES/NO
YES
Defines the LED operation mode.
YES: Detector's LED activated
NO: Detector's LED deactivated

Page 68
Zones: Parameters
Parameter Default Range
Abort Alarm YES YES/NO
This parameter defines whether a zone alarm report to the monitoring station
will be immediate or delayed:
YES: A report to the MS will be delayed according to the Abort Time Delay
parameter (CommunicationMSMS TimesAbort Alarm).

Note: If a valid User Code is entered to reset the alarm within the cancel delay
time (CommunicationMSMS TimesCancel Report), a cancel report
alarm code will be sent to the Monitoring Station.

NO: A report to the MS will be sent immediately.

Presence Disable Enable/Disable
A zone that is set as Presence will send a push notification to the end-user when
triggered during disarm state:
1) Enable or 2) Disable sending a push notification to the end-user.

Note: The Presence push notifications option must also be selected in the
RISCO Cloud for the notifications to be sent to the end-user’s smartphone. he
Presence zone can also be muted via the RISCO Cloud

Sensitivity (Only for 2-way PIR, 2-way WatchOUT, and 2-way Curtain
detectors)

Defines the sensitivity of the detector.

o Low (2 -way PIR, 2 -way WatchOUT, and 2-way Curtain)
o Medium (2-way WatchOUT)
o High (2 -way PIR, 2 -way WatchOUT, and 2-way Curtain)
o Maximum (2-way WatchOUT)
RWX106 Detector Parameters (for 2 way WL Indoor Curtain detectors)
LED Enable Yes Yes/No
Defines the LED operation mode.
YES: Detector's LED activated
NO: Detector's LED deactivated
Detection Mode Normal Fast/Normal (2.5 min)
Use this parameter to define the minimum period between alarm transmissions.
Normal: Only one alarm message is transmitted in any 2.5-minute time-period
Fast: Alarm detection is immediately transmitted.
Sensitivity LOW HIGH/LOW
Specifies the level of PIR channel sensitivity.

Page 69
Zones: Parameters
Parameter Default Range
RWX107DT Detector Parameters (for 2 way WL Outdoor DT Curtain detectors)
LED Enable Yes Yes/No
Defines the LED operation mode.
YES: Detector's LED activated
NO: Detector's LED deactivated
Anti-Mask NO YES/NO
Defines whether to activate the operation of anti-masking detection.
Detection Mode Normal Fast/Normal (2.5 min)
Use this parameter to define the minimum period between alarm transmissions.
Normal: Only one alarm message is transmitted in any 2.5-minute time-period
Fast: Alarm detection is immediately transmitted.
Sensitivity LOW HIGH/LOW
Specifies the level of PIR channel sensitivity.
MW Sensitivity 65% Min., 25%, 50%, 65%,
85%, Max.
Specifies the level of MW channel sensitivity.
RWX350D Detector Parameters (for 2 way Beyond WL DT Detectors)
Sensitivity LOW HIGH/LOW
Specifies the level of PIR channel sensitivity.
MW Senstivity 65% Min., 25%, 50%, 65%,
85%, Max.
Specifies the level of MW channel sensitivity.
Anti-Mask NO YES/NO
Defines whether to activate the operation of anti-masking detection.
LED Enabled Yes Yes/No
Defines the LED operation mode.
Yes: Detector's LED activated
No: Detector's LED deactivated
Detection Mode Normal Fast/Normal (2.5 min)
Use this parameter to define the minimum period between alarm transmissions.
Normal: Only one alarm message is transmitted in any 2.5-minute time-period
Fast: Alarm detection is immediately transmitted.
Position Sensor Enabled No Yes/No

Page 70
Zones: Parameters
Parameter Default Range
Specifies whether to send an alarm following change in the position of the
detector.
Camera Parameters (for 2 -way eyeWAVE PIR cameras – RWX95CMP and Beyond WL DT Cameras –
RWX350DC)

Images at Alarm 3 (1–7)

Specifies the number of images to be captured when an alarm event occurs.
Image Interval 1.0 0.5, 1.0, and 2 seconds
Specifies the time in between image captures.
Image Pre- Alarm YES YES/NO
Specifies if an image capture is to be performed upon each System Away arming.
The picture is sent only in the event of an alarm occurrence, together with the
alarm images.
Image Resolution QVGA QVGA (320X240)
VGA (640X480)
Specifies image quality, as defined by pixel resolution. A QVGA image file is
approximately 7 Kb and VGA image file is 18 Kb
Image Quality High High/Low
Specifies the extent of jpeg image lossy compression (Low=more compression,
smaller file size; High=less compression, larger file size)

Page 71
Zones: Parameters
Parameter Default Range
Colored Image YES YES/NO
Specifies whether the captured and transmitted photographic image is to be color
or black and white.
Camera Trigger
Enables a PIR camera to “follow” (capture and send snapshots) of event
activations (other than those of the PIR camera itself) which occur within the
PIR’s partitions. The snapshots are sent to the Follow Me user and/or monitoring
station to help verify if an alarm event is real. At the keypad, PIRs can be
configured as “Y” to “follow” any of the selections listed below.
NOTE: All selections have defaults as “N” except for Intruder:
 Follow System:
 Duress Y/N N
 Follow Partition (can only follow the same
partitions configured for the PIR’s detection):
 Panic Y/N N
 Fire Y/N N
 Emergency/Medical Y/N N
 Intruder Y/N Y
 Tamper Y/N N
 No Activity Y/N N
 Confirmed Alarm Y/N N
 Follow Zone (camera is activated following a zone alarm or tamper):
 Zone 01 Y/N N
 Zone 02 Y/N N
 Etc.

Page 72
Zones: Parameters
Parameter Default Range
X73 Parameters
This section refers to the programming options of the two-way magnetic contact
RWX73M and RWX73F.
NOTE: After programming X73 parameters and exiting Programming mode, press the
Tamper switch for 3 seconds, and then wait 1 minute for the main panel to download the
parameters to the detector.
RWX73 M Parameters
The RWX73M is a 2-way supervised transmitter that combines Magnetic/Door contact
against opening doors and windows with additional universal input. The RWX73M
operates with RISCO Group 2-way wireless systems
Magnet Enable Enable/Disable
Enable or disable the transmitter’s magnet.
Alarm Hold On On On/Off
Use this parameter to define the minimum period between alarm transmissions.
ON: Only one alarm message is transmitted in any 2.5 minute time-period
OFF: Alarm detection is immediately transmitted
Input Termination (IN 1): NO NO/NC/DEOL/Shutter
Use this parameter to program the connection type used for each of the
system's zones.
N/O: Uses normally-open contacts and no terminating End-of-Line Resistor.
N/C: Uses normally-closed contacts and no terminating End-of-Line Resistor.
DEOL: Uses normally-closed (NC) contacts in a zone using two 10 KΩ of End-of-
Line Resistors to distinguish between alarms and tamper conditions.
Shutter: Specifies that the Input will count the number of open and close pulses
received. If the zone exceeds the predefined number of pulses, the zone will be
tripped and act according to its type definition. After a 25-second timeout, the
pulse counter is restarted. The pulse length is the currently defined Loop
Response time period.
Input Response Time 500 10–500 ms
Set the duration for which a zone violation must exist in order for the zone to
trigger an alarm condition.
Shutter Pulse 02 01-16
Define here the number of pulses for the input.

Page 73
Zones: Parameters
Parameter Default Range
RWX73 F Parameters (Universal/Shutter Mode)
The RWX73F is a 2-way multi-function supervised transmitter with two separate
channels that combines Magnetic/Door contact against opening doors/windows with an
additional universal input or shutter.
The RWX73F has two reed switches for protection against opening doors and windows,
and against any attempt to tamper the detector using large magnets.
The RWX73F operates with RISCO Group 2-way wireless systems
Alarm Hold On On On/Off
Use this parameter to define the minimum period between alarm transmissions.
ON: Only one alarm message is transmitted in any 2.5 minute time-period
OFF: Alarm detection is immediately transmitted
Input 2 Termination (External Zone): NO NO/NC/DEOL/Shutter
Use this parameter to program the connection type used for Input 2.
N/O: Uses normally-open contacts and no terminating End-of-Line Resistor.
N/C: Uses normally-closed contacts and no terminating End-of-Line Resistor.
DEOL: Uses normally-closed (NC) contacts in a zone using two 10 KΩ of End-of-
Line Resistors to distinguish between alarms and tamper conditions.
Shutter: Specifies that the Input 2 will count the number of open and close pulses
received. If the zone exceeds the predefined number of pulses, the zone will be
tripped and act according to its type definition. After a 25-second timeout, the
pulse counter is restarted. The pulse length is the currently defined Loop
Response time period.
Input 2 Response Time 500 10–500 ms
Set the duration for which a zone violation must exist in order for the zone to
trigger an alarm condition.
Shutter Pulse 01-16

Define here the number of pulses for the input.

RWX73 F Parameters (Universal Mode)
The RWX73F is a 2-way multi-function supervised transmitter with two separate
channels that combines Magnetic/Door contact against opening doors/windows with an
additional universal input.
The RWX73F has two reed switches for protection against opening doors and windows,
and against any attempt to tamper the detector using large magnets.
The RWX73F operates with RISCO Group 2-way wireless systems
Magnet Enable Enable/Disable

Page 74
Zones: Parameters
Parameter Default Range
Enable or disable the transmitter’s magnet.
Alarm Hold On On On/Off
Use this parameter to define the minimum period between alarm transmissions.
ON: Only one alarm message is transmitted in any 2.5 minute time-period
OFF: Alarm detection is immediately transmitted
Input 1 Termination (External Zone): NO NO/NC/DEOL
Use this parameter to program the connection type used for Input 1.
N/O: Uses normally-open contacts and no terminating End-of-Line Resistor.
N/C: Uses normally-closed contacts and no terminating End-of-Line Resistor.
DEOL: Uses normally-closed (NC) contacts in a zone using two 10 KΩ of End-of-
Line Resistors to distinguish between alarms and tamper conditions.
Input 1 Response Time 500 10–500 ms
Set the duration for which a zone violation must exist in order for the zone to
trigger an alarm condition.
Anti-Sabotage Disable Enable/Disable
Enable or disable the transmitter’s anti-sabotage magnet.
Two-way Smoke Detector Parameters
Operation Mode Smoke/Heat/
Smoke + Heat
Set operation mode of the two-way smoke detector (model RWX34S):
Smoke Only: Smoke alarm only
Heat Only: Heat alarm only
Smoke + Heat: Smoke or heat alarm
RWX78M Parameters (2 way Slim Contact detectors)
LED On On/Off
Defines the LED operation mode.
On: Detector's LED activated
Off: Detector's LED deactivated
Hold On On On/Off
Use this parameter to define the minimum period between alarm transmissions.
ON: Only one alarm message is transmitted in any 2.5-minute time-period
OFF: Alarm detection is immediately transmitted.
RWX78S Detector Parameters (for 2 way Slim Shock detectors)
LED Enabled Yes Yes/No

Page 75
Zones: Parameters
Parameter Default Range
Defines the LED operation mode.
Yes: Detector's LED activated
No: Detector's LED deactivated
Shock Sensitivity TBD 0-100%
Defines the detector’s level of sensitivity.
RWX78SM Detector Parameters (for 2 way Slim Shock and Contact detectors)
Magnet
LED Enabled Yes Yes/No
Defines the LED operation mode.
Yes: Detector's LED activated
No: Detector's LED deactivated
Hold On On On/Off
Use this parameter to define the minimum period between alarm transmissions.
ON: Only one alarm message is transmitted in any 2.5-minute time-period
OFF: Alarm detection is immediately transmitted.
Shock
Shock Enabled Enabled/Disabled
Defines whether to enable or disable shock detection
LED Enabled Yes Yes/No
Defines the LED operation mode.
Yes: Detector's LED activated
No: Detector's LED deactivated
Shock Sensitivity TBD 0-100%
Defines the detector’s level of sensitivity.
RWX78SM Detector Parameters (for 2 way Slim Shock and Contact detectors)
RWX78MU Detector Parameters (for 2 way Magnetic Contact and Universal detectors)
Magnet
LED Enabled Yes Yes/No
Defines the LED operation mode.
Yes: Detector's LED activated
No: Detector's LED deactivated
Hold On On On/Off

Page 76
Zones: Parameters
Parameter Default Range
Use this parameter to define the minimum period between alarm transmissions.
ON: Only one alarm message is transmitted in any 2.5-minute time-period
OFF: Alarm detection is immediately transmitted.
Universal
Universal Enable Enable/Disable
Defines whether to enable or disable the universal zone input.
LED Enabled Yes Yes/No
Defines the LED operation mode.
Yes: Detector's LED activated
No: Detector's LED deactivated
External Zone NO/NC/DEOL/Shutter
Defines the termination of the external zone input.
Response Time 10/500 ms
Define the response time of the external zone input (applicable for NO and NC
terminations only).
Hold On On On/Off
Use this parameter to define the minimum period between alarm transmissions
(not applicable for shutter termination).
ON: Only one alarm message is transmitted in any 2.5-minute time-period
OFF: Alarm detection is immediately transmitted.
Pulses number On 2/4/6/8/10/12/14/16
Defines the pulse number threshold for shutter input.
Input Protection On On/Off
Defines whether to generate a tamper message due to input wires shorted
(applicable for shutter only).
RWX78SMU Detector Parameters (for 2 way Magnetic Contact, Shock and Universal detectors)
Magnet
LED Enabled Yes Yes/No
Defines the LED operation mode.
Yes: Detector's LED activated
No: Detector's LED deactivated
Hold On On On/Off

Page 77
Zones: Parameters
Parameter Default Range
Use this parameter to define the minimum period between alarm transmissions.
ON: Only one alarm message is transmitted in any 2.5-minute time-period
OFF: Alarm detection is immediately transmitted.
Shock
Shock Enabled Enabled/Disabled
Defines whether to enable or disable shock detection
LED Enabled Yes Yes/No
Defines the LED operation mode.
Yes: Detector's LED activated
No: Detector's LED deactivated
Shock Sensitivity TBD 0-100%
Defines the detector’s level of sensitivity.
Universal
Universal Enable Enable/Disable
Defines whether to enable or disable the universal zone input.
LED Enabled Yes Yes/No
Defines the LED operation mode.
Yes: Detector's LED activated
No: Detector's LED deactivated
External Zone NO/NC/DEOL/Shutter
Defines the termination of the external zone input.
Response Time 10/500 ms
Define the response time of the external zone input (applicable for NO and NC
terminations only).
Hold On On On/Off
Use this parameter to define the minimum period between alarm transmissions
(not applicable for shutter termination).
ON: Only one alarm message is transmitted in any 2.5-minute time-period
OFF: Alarm detection is immediately transmitted.
Pulses number On 2/4/6/8/10/12/14/16
Defines the pulse number threshold for shutter input.
Input Protection On On/Off
Defines whether to generate a tamper message due to input wires shorted
(applicable for shutter only).

Page 78
Zones: Parameters
Parameter Default Range
RWX78SU Detector Parameters (for 2 way Shock and Universal detectors)
Shock
LED Enabled Yes Yes/No
Defines the LED operation mode.
Yes: Detector's LED activated
No: Detector's LED deactivated
Shock Sensitivity TBD 0-100%
Defines the detector’s level of sensitivity.
RWX78SM Detector Parameters (for 2 way Slim Shock and Contact detectors)
Universal
Universal Enable Enable/Disable
Defines whether to enable or disable the universal zone input.
LED Enabled Yes Yes/No
Defines the LED operation mode.
Yes: Detector's LED activated
No: Detector's LED deactivated
External Zone NO/NC/DEOL/Shutter
Defines the termination of the external zone input.
Response Time 10/500 ms
Define the response time of the external zone input (applicable for NO and NC
terminations only).
Hold On On On/Off
Use this parameter to define the minimum period between alarm transmissions
(not applicable for shutter termination).
ON: Only one alarm message is transmitted in any 2.5-minute time-period
OFF: Alarm detection is immediately transmitted.
Pulses number On 2/4/6/8/10/12/14/16
Defines the pulse number threshold for shutter input.
Input Protection On On/Off
Defines whether to generate a tamper message due to input wires shorted
(applicable for shutter only).

Page 79
Alarm Confirmation
The Alarm Confirmation menu enables to define protection against false alarms and will
be used for alarm verification.
Zones: Alarm Confirmation
Parameter Default Range
Confirm Partition
Defines which partitions will be defined for alarm sequential confirmation.
Each confirmed partition has a separate timer, which is equivalent to the confirmation
time defined in “Confirmation Time Window”.
A confirmed intruder alarm will be reported if two separate alarm conditions are
detected in the same confirmed partition, during the confirmation time.
Confirm Zones
Define which zones will be defined for alarm sequential confirmation.
When the first zone goes into alarm the system transmits the first zone alarm. When the
second zone goes into alarm, during the confirmation time, the panel transmits the zone
alarm and the Police code.
Notes:
1. A confirmed zone will be part of the sequential confirmation only if the partition in which the
alarm occurs is defined as confirmed partition as well.
2. Any Code can reset a confirmed alarm.
3. If the first zone is violated and not restored until the end of the confirmation time (no second
zone alarm), then this zone will be excluded from the confirmation process until the next arming.

Soak Test
The Soak Test feature is designed to allow false alarming for predefined detectors to be
omitted from the system, while any alarms generated are displayed to the user for
reporting to the MS. This is especially useful if Police response withdrawal is being
threatened and a particular zone is causing unidentified problems.
Each zone can be placed on Soak Test. Any zone placed in the Soak Test list is omitted
from the system for 14 days and is automatically reinstated after that time if NO alarms
have been generated by it.
If a zone in the Soak Test list has an alarm during the 14-day period, the keypad indicates
to the user that the test has failed. After the user looks at the View Fault option, the fault
message will be erased. This will be indicated in the event log, but no alarm will be
generated. The alarmed zone's 14-day Soak Test period is then reset and restarted.

Page 80
Cross Zones
The Zone Crossing menu is used for additional protection from false alarms and contains
parameters that enable you to link together two related zones. Both must be violated
within a designated time period (between 1 and 9 minutes) before an alarm occurs.
This type of linking is used with motion detectors in hostile or false-alarm prone
environments. Default: No Zone crossing
Zones: Zone Crossing
Parameter
1st Zone
The 1st zone of a pair of zones defined for zone crossings.
2nd Zone
The 2nd zone of a pair of zones defined for zone crossings.
Time
The amount of time allowed between the triggering of events for both zones to be
considered a valid violation
Correlation Type
Determines how the Agility 4 will process violations of the paired zones. Please note that
in either of the following cases, both of the (paired) zones need to be tripped in order to
have alarm activation.
 Not correlate: Temporarily disables any associated zone pairings
 Ordered correlate: Triggers an alarm only if the 1st zone is tripped before
the 2nd.
 Not ordered correlate: Triggers an alarm regardless of which of the two
zones is tripped first.

Note: Zones crossed within themselves are valid pairs. They need to register a violation twice to trigger the
alarm. This process is known as Double Knock.

Page 81
2.2.2 Remote Controls
The Remote Controls menu defines the operation of the remote controls. Up to 8 remote
controls can be assigned to the system. The system supports 2 types of remote controls:
One-way remote controls (4 button)
Two-way (bidirectional) remote controls (8 button)

Parameters
The programming options under the parameters menu vary according to the type of the
remote control.
One Way Remote Control Parameters
Each one-way remote control consists of 4 buttons, and each button can be programmed to
a different mode of operation.
Remote Controls Parameters: One Way Remote Controls
Parameter
Label
A label identifying the user of the remote control.
Serial Number
The serial number of the remote control. Each wireless device has its own unique serial
number. Placing ID 00000000000 will delete the remote control’s allocation.
Partition
Assign the relevant partitions for the selected remote control.
Button 1 ()
Set the operation of button 1 of the remote control from the following options:
o None: Button disabled.
o Arm: The button is used for Away (Full) arming of the remote control's partitions.
o Stay: The button is used for Stay (Home) arming of the remote control's partitions.
Button 2 ()
Set the operation of button 2 of the remote control from the following options:
o None: Button disabled.
o Disarm: The button is used for disarming its assigned partitions.
Button 3
Set the operation of button 3 (Small blank button) of the remote control from the
following options:
o None: Button disabled.
o Panic: The button is used to send a panic alarm.
o Status: Main unit broadcast of system status
o UO Control (1-20): The button is used to operate a single utility output.

Page 82
Remote Controls Parameters: One Way Remote Controls
Parameter
Button 4
Set the operation of button 4 (Large blank button) of the remote control from the
following options:
o None: Button disabled.
o Arm: The button is used for Away (Full) arming of the remote control's partitions.
o Stay: The button is used for Stay (Home) arming of the remote control's partitions.
o UO Control (1-20): The button is used to operate a utility output.
Two Way Bi-directional Remote Controls
The bidirectional remote control is a 4 or 8 button rolling code wireless transmitter
designed for remote system operation. Being bi-directional enables each command that is
sent to the panel to receive a reply status indication back from the panel using its 3 color
LEDs and internal buzzer siren. For higher security, commands can be defined to be
activated with a 4-digit PIN code (8-button remote control).
Remote Controls Parameters: 2 Way Remote Control
Parameter
Label
A label identifying the user of the remote control.
Serial Number
The serial number of the remote control. Each wireless device has its own unique serial
number. Placing ID 00000000000 will delete the remote control’s allocation.
Partition
Assign the relevant partitions for the selected remote control.
PIN Code
4 digit PIN code used for higher security when sending commands from the remote
control. The code can be comprised using digits 1,2,3,4.
Note: The use of the PIN code depends on the control Quick UO or system control Quick Arm

Panic Function N

Use to toggle between Y (yes) and N (no) to define whether or not sending a panic

alarm from the remote control is permitted. If permitted, pressing on keys and
simultaneously for 2 seconds will send a panic alarm.
UO Key 1/2/3
Each remote control can activate up to 3 outputs. Assign to each of the keys 1-3 the
relevant output.

Page 83
Controls
The Controls menu options are used for both types of remote controls.
Remote Controls: Controls
Control
Instant Arm YES
YES: Away arming from any remote control will be instant.
NO: Away arming from any remote control will be delayed, following exit delay 1.
Instant Stay YES
YES: Stay arming from any remote control will be instant.
NO: Stay arming from any remote control will be delayed, following exit delay 1.
Disarm + Code (For 2 Way Remote Controls) NO
Defines if a PIN code is required to perform the disarm operation while using any of the
bidirectional remote controls.

Parent Control
The Parent Control option is used to monitor the activity of children. This option allows
you to monitor when the children arrive home and disarm the system or when they arm
the system in Away, using a remote control or the keypad. With each
activation/deactivation of the system a message is sent to a specified Follow Me number.

After selecting this option, using the / key, define which of the remote controls
are authorized with this feature and which are not.
2.2.3 Keypads
The system can support up to 3 wireless keypads, of two kinds: LCD/Panda keypads, or
Outdoor/Indoor Slim keypads.
For detailed information regarding the operation of the keypads refer to the instructions
supplied with the product.

Parameters
Keypads: Parameters
Parameter Default Range
Label
A label identifying the keypad
Serial Number
The unique serial number of the keypad. Each wireless device has its own unique serial
number. Placing ID 00000000000 will delete the keypad’s allocation.

Page 84
Keypads: Parameters
Parameter Default Range
Emergency Keys YES YES/NO
Defines whether the following keys will be activated or not (Y / N) to operate as
emergency keys
LCD Keypad:

o Press Keys and simultaneously to send a fire alarm.

o Press Keys and simultaneously to send an emergency alarm.

Panda Keypad:

o Press Keys and simultaneously to send a fire alarm.

o Press Keys and simultaneously to send an emergency alarm.

Slim Keypad:
o Press buttons + simultaneously for two seconds to send a panic alarm
o Press buttons + simultaneously for 2 seconds to send a fire alarm
o Press buttons + simultaneously for 2 seconds to send an emergency / medical
alarm
Function Key (Only LCD keypad) Panic

Defines the operation of the keys for each keypad.

o Disabled: Keys disabled.
o Panic Alarm: Send a panic alarm to the monitoring station.
o MS Listen /Talk: The system dials the monitoring station to establish 2-way
communication.
UO Control

Assign outputs that will be activated by a long press on keys on the

bidirectional keypad.
Notes:
Outputs can be assigned only if I/O is assigned to the system.
Each keypad can activate different outputs.
Only outputs defined as Follow Code can be activated by the keypad keys

Page 85
Mode (only for slim keypad)
Use this parameter to define the slim keypad operation mode.
1. Arm/Disarm: the slim keypad is to have full user control of the system.
2. Bypass: designed for the Danish market; the slim keypad is to operate in
bypass mode.
Note: For further information, see the keypad documentation.
Door Bell Sound (only for slim keypad)
Use this parameter to define the chime sound (broadcast by the main unit) when the slim
keypad door chime button ( ) is pressed as follows:
 None
 Chime sound 1/2/3
Supervision
Choose if the keypad (Slim, LCD or Panda) will be supervised or not.
Auto Status
The panel provides relevant data on the keypad icons, following keypad wake up by the
user. For example, connection status and arm/disarm state.

Controls

The Controls menu defines programming options that are used for all keypads.
Keypads: Controls
Parameter Default Range
RF Wake-up NO YES/NO

Use to toggle between Y (yes) and N (no) to define whether the system can wake
the keypad up during exit/entry times or when failing to set the system.
YES: The system wakes the keypad.
NO: The system cannot wake up a keypad. Use this option to save battery life. (Default)

2.2.4 Sirens
The Sirens menu enables to define all parameters of external and internal wireless sirens
that can be connected to the system. Up to 3 sirens can be added to the system.
For detailed information regarding the operation of the sirens refer to the instructions
supplied with the product.
Wireless Device: Sirens
Parameter Default Range
Label
A label identifying the siren.
Serial Code

Page 86
Wireless Device: Sirens
Parameter Default Range
The unique serial number of the sirens. Each wireless device has its own unique serial
number. Placing ID 00000000000 will delete the siren’s allocation.
Partition
Assign the partitions that will affect the sounder operation.
Supervision YES
Choose if the siren will be supervised or not.
Volume 9 0-9
Define the volume of the sounder for the following scenarios in the system.
Alarm Volume 9 0-9
The sound volume produced during an alarm (0 indicates silence).
Squawk Volume 5 0-9
The sound volume produced during squawk sounds (0 indicates silence).
Exit/Entry Volume OFF 0-9
The sound volume produced during exit/entry time. (0 indicates silence).
Strobe (External siren only)
Defines the parameters for the strobe of the external siren.
Strobe Control
Defines the Strobe operation mode:
o Always off: The strobe is deactivated
o Follow Bell: The strobe is activated once when the siren bell is triggered
o Follow Alarm: The strobe is activated when an alarm event occurs in the
system
Strobe Blink 40
Defines the number of times that the strobe will blink in a minute:
o 20 times per minute
o 30 times per minute
o 40 times per minute
o 50 times per minute
o 60 times per minute
Strobe Arm Blink 05 00-20
Defines the time that the strobe will blink when the system is armed.

Page 87
2.2.5 Wireless I/O Expander
The Wireless Input/Output Expander is a self powered device enabling system control of
additional 4 wired zones and has home automation capabilities. With the I/O Expander the
system can control 4 outputs and 16 home automation units employing the X10 protocol.

Wired Zones
The 4 inputs on the I/O Expander are regarded as zones 33-36 in the system.
I/O Expander: Wired Zones
Parameter Default Range
Label
A label identifies the zone in the system. (up to 16 characters).
Partition 1
The partitions assignment for each zone.
Type Intruder
Contains parameters that enable you to program the zone type for any zone. Refer to
page 61 for a list of Zone Type options.
Sound Bell
Contains parameters that enable you to program the sound produced when a system
zone triggers an alarm for the time defined under the Bell Time Out parameter. Refer to
the list of options for the Zone Sound on page 67.
Advanced programming
Chime None
The Chime parameter is used as an audible indication to a zone violation while the
system is Disarmed. When violated, the main unit can sound one of the 5 available
chime options.
Control
Forced Arming N
Define whether the zone can be force armed or not. For more information
regarding the force arming feature refer to page 68.
No Activity N
Determines whether the zone participates in the No Activity function. The No
Activity function is for reception of signals used to monitor the activity of sick,
elderly or disabled people. For more information regarding the force arming
feature refer to page 68.
Abort Alarm Y
This parameter defines whether a zone alarm report to the monitoring station
will be immediate or delayed. For more information regarding the force arming
feature refer to page 68.

Page 88
I/O Expander: Wired Zones
Parameter Default Range
Termination
The Termination menu enables you to program the connection type used for the wired
zones 33-36. The actual (physical) termination for each zone must comply with that
selected in the zone termination menu.
o N/C: (Normally Closed) Uses normally-closed contacts and no terminating End-of-
Line Resistor.
o N/O: (Normally Open) Uses normally-open contacts and no terminating End-of-Line
Resistor
o EOL: (End of Line) Uses normally-closed (NC) and/or normally-open (NO) contacts
in a zone terminated by a supplied 2200 End-of-Line Resistor
NORMALLY CLOSED NORMALLY OPEN ZONE END OF LINE ZONE END OF LINE ZONE
ZONE CONFIGURATION CONFIGURATION (N.C CONTACT) (N.O CONTACT)
zone com zone com zone com zone com

2.2 K
2.2 K

ALARM
ALARM ALARM ALARM
DETECTOR DETECTOR DETECTOR DETECTOR D

Loop response
The Loop Response menu enables you to set the different times for which a wired zone
violation must exist before the zone will trigger an alarm condition.
The following option are available:
Normal 400 ms 0.5 hours 2 hours 3.5 hours
Slow: 1 second 1 hour 2.5 hours 4 hours
Fast: 10 ms 1.5 hours 3 hours

Detection Mode
o Normal (Default): 2.5 minutes dead time between alarm detections transmissions.
o Fast (Walk Test): Alarm detection is immediately transmitted.

Page 89
Output Parameters
The I/O expander has 4 physical outputs on board. (2 relay 3Amp and 2 Transistor Outputs
(500 mA)
I/O Expander: Output Parameters
Parameter Default Range
Label
A label identifies the output in the system.
Type
There are 4 types of outputs in the system as follows
o Not Used
o Follow System: The utility output will follow a System Event
o Follow Partition: The utility output will follow a Partition Event.
o Follow Zone: The utility output will follow a Zone Event. Each Utility Output can be
activated by a group of up to five zones.
o Follow Code: The utility output will be activated by a user defined as UO Control or
from the user programming menu.
Follow System Events:
Bell
Activates when a bell is triggered. If a bell delay was defined, the utility output
will be activated after the delay period.
No Telephone Line
Activates when a telephone line fault is detected. If a PSTN Lost Delay time
period is defined, the utility output will be activated after the delay time
Monitoring Station Communication Fail
Activates when communication with the Central Station cannot be established.
Deactivates after a successful call is established with the Central Station.
General Trouble
Activates when a system trouble condition is detected.
Deactivates after the trouble has been corrected
Main unit Low battery
Activates when the Agility 4 battery has insufficient reserve capacity and the
voltage decreases to 6V.
AC Loss
Activates when the source of the main panel’s AC power supply is interrupted.
This activation will follow the delay time defined in the system control times
and the AC Off Delay Time parameter.

Page 90
I/O Expander: Output Parameters
Parameter Default Range
Bell burglary
Activates the Utility Output after any bell burglary alarm in any partition in the
system.
Scheduler
The utility output will follow the predefined time programming that is defined
in the scheduler of the weekly programs for utility output activation.
Tamper
Activates the utility output when a Tamper occurs in the system.
Duress
Activates the Utility Output when a duress alarm is initiated by any user
defined as duress code.
GSM Trouble
Activates the utility output when there is trouble in the GSM module.
Follow Open Delay
This output is activated once an Entry Bypass timer starts (see Entry Bypass,
page 45). The output is designed to be part of the bypass keypad solution for
the Danish market. The output behavior depends on the output pattern as
follows:
Pulsed: Use this option to activate an electronic lock. The time duration is as
defined by the installer under Pulse Duration Length (see Pulse Duration Length,
page 94).
Latched: While the system is disarmed, entering a bypass code will activate the
output like an access control reader. Output operation using the bypass code
during disarm mode will not be registered in the event log.
During Away mode, opening an Open Delay zone (during the Bypass Entry
Time) will shorten the output time to 3 seconds.
Door Bell
Activates the Utility Output when a door button is pressed on a slim keypad.
This output operates only as a pulse output (as defined by Pulse Duration
Length (see Pulse Duration Length, page 94).
Follow Partition Events:
Ready
Activates the utility output when all the selected partition(s) are in the Ready
state.

Page 91
I/O Expander: Output Parameters
Parameter Default Range
Arm
Activates the utility output when the selected partition(s) is armed in Away
(Full) mode. The utility output will be activated immediately, regardless of the
Exit Delay time period.
Disarm
Activates the Utility Output when the selected partition(s) is disarmed.
Alarm
Activates the Utility Output when an alarm occurs in the selected partition(s).
Intruder alarm
Activates the utility output when an intrusion (Burglary) alarm occurs in the
selected partition(s).
Fire
Activates the utility output when a fire alarm is triggered in the selected
partition(s) from the keypads or a zone defined as Fire.
Panic
Activates the utility output when a panic alarm is triggered in the selected
partition(s) from the keypads, remote controls or a zone defined as Panic.
Special
Activates the utility output when a special alarm is triggered in the selected
partition(s) from the keypads or a zone defined as Special .
Exit/Entry
Activates the Utility Output when the selected partition(s) initiates an
Exit/Entry Delay period.
Zone Bypass
Activates the Utility Output when the relevant partitions are in ARM or STAY
mode and any zone in the relevant partitions is bypassed.
Auto Arm Alarm
Activates the utility output when there is a not ready zone at the end of the pre-
warning time during an auto-arm process. The output restore shall be on Bell-
Timeout or at user Disarm.
Zone Lost
Activates the utility output when there is a lost wireless zone in the system. The
output restore shall be on Bell-Timeout or at user Disarm.

Page 92
I/O Expander: Output Parameters
Parameter Default Range
Stay Follow
Activates the Utility Output when the selected partition(s) is armed in Stay
mode.
Chime Follow
Activates the Utility Output following a chime sound in the selected partition(s)
Bell Stay Off
This parameter causes the utility output to function as follows:
 In Away arming mode, the utility output will follow the bell activation
in the defined partitions.
 In Stay arming mode, the utility output will not be activated.
Bell
Activates the utility output when one of the defined partitions is in Alarm
mode and the bell is triggered. This enables the connection of different sirens to
different partitions.
No Activity
Activates the utility output when an event of NO ACTIVITY occurs in the
system. . The No Activity function is for reception of signals used to monitor
the activity of sick, elderly or disabled people
Confirmed alarm
Activates the utility output when a confirmed alarm occurs in the system.
Follow Zone Events:
Zone
Activates the utility output when the selected zone is tripped.
The tripped zone need not be armed to trigger the Utility Output.
Alarm
Activates the utility output when the selected zone causes an alarm.
Arm
Activates the utility output when the selected zones are armed.
Disarm
Activates the utility output when the selected zones are disarmed.

Page 93
I/O Expander: Output Parameters
Parameter Default Range
Follow User Code:
Defines the User Code(s) for triggering the selected UO. The activation of the

UO is performed from the User Activities menu. Use / to toggle

between [Y] YES or [N] NO for each user chosen to trip the designated Utility
Output.
Pattern
For each output you need to define the pattern of operation. The available options are:
Pulse N/O (Normally Open)
The utility output is always Deactivated (N/O) before it is triggered (pulled up).
When triggered, it activates (pulled down) for the Pulse Duration specified,
then deactivates automatically.
Latched N/O (Normally Open)
The Utility Output is always Deactivated (N/O) before it is triggered (pulled
up). When triggered, it activates (pulled down) and remains activated (latched)
until the operation is restored.
Pulse N/C (Normally Closed)
The utility output is always Activated (N/C) before it is triggered (pulled down
to negative). When triggered, it deactivates for the Pulse Duration specified
below and then reactivates automatically.
Latched N/C (Normally Close)
The Utility Output is always Activated (N/C) before it is triggered (pulled
down to negative). When triggered, it deactivates and remains deactivated
(latched) until the operation is restored.
Activation / Deactivation
When the utility output is following more than one partition or zone, the installer can
choose the logic of the Utility Output activation as follows:
o If the pattern operation of the output is defined as Latch N/O or Latch N/C, the
activation and deactivation of the outputs can follow either after all the
Partitions/Zones or after any of the Partitions/Zones.
o If the Pattern operation of the output is defined as Pulse N/O or Pulse N/C, the
activation of the outputs can follow either after all the Partitions/Zones or after any of
the Partitions/Zones. The deactivation operation follows the defined time period.
Pulse Duration Length 05 sec 01-90
The time that an output defined as Pulsed N.O or Pulsed N.C will be activated. At the
end of the pulse duration the output reactivates automatically.

Page 94
X-10 Outputs
The wireless I/O expander enables the system to control X – 10 devices. The I/O expander
converts the information sent from the programmable utility output into the X – 10
protocol. Up to sixteen X-10 devices can be activated. These are recognized in the system as
outputs 5-20.
I/O Expander: X-10 Outputs
Parameter Default Range
Label
A label identifies the output in the system
Type
Refer to the explanation under the utility output section.
Pattern
Refer to the explanation under the utility output section.
Pulse Length 05 sec 01-90
Refer to the explanation under the utility output section.

Parameters
The following table describes the general parameters for the I/O module.
I/O Expander: Parameters
Parameter Default Range
Serial Number
The internal ID number of the I/O Expander. Each wireless device has its own unique
serial number.
Controls
I/O Expander Supervision
Choose if the I/O Expander will be supervised or not.
Quick Output Operation
A user can activate a UO from the bidirectional remote control or keys

on the wireless keypad without the need to enter his user code.
X-10 House ID
Defines the house code, which matches the code defined by the X-10 modules.
UO DTMF Control
The Agility 4 enables to activate 8 utility outputs from remote DTMF phone. To operate
a UO via the telephone you must assign a specific UO to a digit on the phone.

Page 95
2.3 Identification
This option provides the ability to identify the serial number of a wireless device in the
system from a keypad or from the Configuration Software.
When using a keypad follow this procedure:

Go to Programming  Radio Devices Menu  Identification and press / .

The following message appears on the keypad LCD/display:

Press on the device’s Learn mode. The serial number of the relevant device appears on
the keypad LCD/display.

2.4 Delete
For deletion of single devices, see Deleting a Single Device from the LCD/Panda Keypad, page
37.

Page 96
3. Programming: Codes Menu
The Codes menu provides the ability to define parameters and codes for the system users.
3.1 User
User rights can be defined by allocating each user a specific authority level and specific
partitions. Up to 32 users can be defined in the system.
Codes: User Codes
Parameter Default
Labels
Used to describe the user. Up to 32 characters can be used.
Partition
Enables you to assign the partition/s (1—3) in which each user (except for the Grand

Master, whom can operate all 3) can operate. Use / to scroll to the

partitions, and then press / to toggle between enabling [Y] or disabling.

Authority Level
Allocate an authority level to a user according to the following list:
NOTE: The installer does not assign the actual codes. Assigning the codes is done by the Grand
Master / system users.
User: There are no restrictions in the number of User Codes (as long as they do
not exceed the number of codes remaining in the system). The User has access to
the following:
 Arming and disarming
 Bypassing zones
 Viewing system status, trouble, and alarm memory
 Activating designated Utility Outputs
 Changing his/her own User Code
 Setting keypad's settings
Cleaner: The Cleaner Code is a temporary code, which is to be immediately
deleted from the system as soon as it is used to arm. This code is typically used
for maids, home attendants, and repairmen who must enter the premises before
the owner(s) arrive. These codes are used as follows:
 For one-time arming in one or more partitions
 If first used to disarm the system, the code may be used once for subsequent
arming
Arm Only: There are no restrictions in the number of Arm Only Codes (as long as
they don't exceed the number of codes remaining in the system). Arm Only Codes
are useful for workers who arrive when the premises are open, but typically are

Page 97
Codes: User Codes
Parameter Default
last to leave, thus they typically close the premises and arm the system. The users
with Arm Only Codes have access for arming one or more partitions.
Duress: When forced into disarming the system, by entering a specific code, a
system user can comply with the intruder's demands while simultaneously sendin
a silent duress alarm to the monitoring station. In any other situation the duress
authority level behaves as the same as the user authority level (see prior page).
NOTE: Under no circumstances should the duress code be used haphazardly or without
reason. Monitoring stations, along with police departments, treat duress codes very
seriously and take immediate action.
Door Bypass: Use this authority level when the slim keypad reader is defined in
Bypass mode. The authorization code defined here initiates the Entry Bypass
Timer (see Entry Bypass, page 45). This authority is recognized only on a slim (not
LCD/Panda) keypad.
3.2 Grand Master
The Grand Master Code (default = 1234) is typically used by the system's owner and is the
highest Authority Level. This person can set/change the Grand Master Code.
NOTE: In the Configuration Software the Grand Master is identified as code 00.

3.3 Installer
The Installer Code provides access to the Installer Programming menu, allowing
modification of all system parameters. The Installer Code is used by the Agility 4
installation company technician to program the system.
The Installer can change the Installer Code.
Default: 0132
3.4 Sub-Installer
The Sub-Installer Code allows limited access to selected parameters from the Installer
Programming menu. It is used by a technician sent by the Agility 4 installation company to
carry out restricted tasks defined at the time of system installation by the installation
technician. The Sub-Installer can access with his code only those programming menus
predefined for his access. Default: 0232
The Sub-Installer is prohibited to access the following parameters:
 Default Enable
 MS Enable
 Configuration Software Enable
 Code Length
 Installer Code

Page 98
NOTE: The Configuration Software and Monitoring Station menus are unavailable to the
sub-installer.
3.5 Code Length
The Code Length specifies the minimum number of digits requested. Default: 4 digits

NOTE: When you change the Code Length parameter, all user codes are deleted and must
be re-programmed or downloaded.
NOTE: For a 6-digit code length system, 4-digit default codes like 1-2-3-4 (Grand Master),
0-1-3-2 (Installer), and 0-2-3-2 (Sub-Installer) become 1-2-3-4-0-0, 0-1-3-2-0-0, and 0-2-3-2-0-
0, respectively.
NOTE: If you change the Code Length back to 4 digits, the system codes are restored to the
default 4-digit codes.

EN50131-3 standard specifications:

 All code length are 4 digits: xxxx
 For each digit 0-9 can be used
 All codes from 0000 to 9999 are acceptable
 Invalid codes cannot be created since after 4 digits are typed, the "Enter" is automatic.
Codes are rejected when trying to create a code that does not exist.

3.6 DTMF Code

This is a telephone remote access code made up of two digits that enables entry into the
system when dialing in from a remote number.
Default code=00
3.7 Parent Control
The Parent Control option is used to monitor the activity of children. This option allows all
users to monitor when the children arrive home and disarm the system or when they arm
the system in Away mode. With each activation/deactivation of the system a message is
sent to a specified Follow Me number.

Use the / key to toggle between [Y] YES or [N] NO for each user chosen to be
assigned with the parent control feature.

Page 99
4. Programming: Communication Menu
The Communication menu provides access to submenus and their related parameters that
enable the system to establish communication with the Monitoring Station, Follow Me or
Upload/Download.
The Communication menu is divided into the following sub-menus:

1. Method
2. Monitoring Station
2. Configuration Software
3. Follow-Me
4. Cloud

4.1 Method Sub-Menu

The Method sub-menu allows you to configure the parameters of the available
communication channels for the system:
1. PSTN
2. GSM
3. IP
4.1.1 PSTN
The PSTN screen contains parameters for the system communication over the PSTN
network
Method: PSTN
Parameter Default Range
Timers
Timers related to communication through the PSTN channel
PSTN Lost 04 00-20 minutes
The time after which the system will regard the PSTN line as lost. This time also
specifies the delay before reporting the event into the event log or operating a
utility output that follows this event.
00 indicates no supervision of the phone line.
Wait for Dial Tone 3 0-255 seconds
The number of seconds the system waits to detect a dial tone.
Control
Alarm Line Cut No
YES: Activates the external sirens if the land line, connected to the Agility 4
panel is cut or the telephone service is interrupted for the time defined in the
PSTN Lost time parameter.
NO: No activation occurs.

Page 100
Method: PSTN
Parameter Default Range
Answering Machine Override Yes
YES: The Answering Machine Override is enabled, as follows:
 The Configuration Software at the alarm company calls the account.
 The software hangs up after one ring by the configuration operator.
 Within one minute, the software calls again.
 The system is programmed to pick up this second call on the first ring, thus
bypassing any interaction with the answering machine.
Note: This feature is used to prevent interference from an answering machine with remote
configuration operations.

NO: The Answering Machine Override is disabled, and communication takes

place in the standard manner.
CS via PSTN Yes
YES: The system allows access to Configuration Software through a PSTN
connection
NO: The system does not allow access to Configuration Software through a
PSTN connection
Parameters
Rings to Answer 12 01 to 15
The number of rings before the system answers an incoming call

Area code
The system area telephone code. This code will be deleted from a telephone
number while the system tries to dial the number through the PSTN network.
PBX Prefix
A number dialed to access an outgoing line when the system is connected to a
Private Branch Exchange (PBX) and not directly to a PSTN line. This number
will be added automatically by the system while trying to call from a PSTN line.

Page 101
4.1.2 GSM
The GSM screen contains parameters for the system communication over the GSM/GPRS
network.
Method: GSM
Parameter Default Range
Timers
Allows to program timers related to operation with the GSM module
GSM Lost 10 min 001-255 min
The time after which the GSM module regards the GSM network as loss.
Network loss is defined as RSSI level below the level defined GSM Network
Sensitivity parameter.
SIM Expire 00 00-36 months
A Pre-paid SIM card has a defined life length defined by the provider. After
each charging of the SIM, the user will have to manually reset the expiration
time of the SIM card. A notification will be displayed on the wireless keypad
when asking for status indication.
Set the SIM expiring date (in months) using the numeric keys, according to the
time given by the provider.

Page 102
Method: GSM
Parameter Default Range
MS Keep Alive (Polling) 00000 0-65535 times
The time period that the system will establish automatic communication
(polling) with the MS over GPRS, in order to check the connection.
3 polling times can be defined: Primary, Secondary and Backup. For each time
period define the number of units between 1- 65535. Each unit represents a time
frame of 10 seconds.
Note: When using the polling feature through GPRS the MS channel parameter must be defined
as GPRS only.
The report code for MS polling is 999 (Contact ID) or ZZ (SIA)

The use of these time periods depends on the reporting order to the MS defined
by the Report Split MS Urgent parameter (See: [4]Communication > [2]MS >
[7]Report Split)
 Primary: This time period is used when the MS channel is defined as GPRS
Only and the Report Split parameter is not defined as 1st backup 2nd.
 Secondary: This time period is used when the MS 2 channel is defined as
IPGPRS Only and the Report Split parameter is defined as 1st backup 2nd.
 Backup: This time period will be assigned to the backup channel in the
following case:

MS 2 channel is defined as IPGPRS Only

Report Split parameter is defined as 1st backup 2nd

The communication with MS 1 is disconnected.
GPRS
Allows programming parameters that relate for the communication over the GPRS
network.
Access Point Network (APN) Code
To establish a connection to the GPRS network an APN (access point name) code
is required. The APN code differs from country to country and from one
provider to another (the APN code is provided by your cellular provider).
The system supports an APN code field of up to 30 alphanumeric characters and
symbols (!, &, ? etc).
APN User Name
Enter APN user name (if required). The user name is provided by your
provider. The system supports a user name field of up to 20 alphanumeric
characters and symbols (!, &, ? etc).

Page 103
Method: GSM
Parameter Default Range
APN Password
Enter the APN password (up to 20 alphanumeric characters and symbols.) as
provided by your provider (if required).
E-mail
The following programming parameters are used to enable sending Follow Me event
messages by e-mail through GPRS.
Note: To enable e-mail messaging, the GPRS parameters have to be defined.

Mail Host
The IP address or the host name of the SMTP mail server
SMTP Port
The port address of the SMTP mail server
Email address
The Email address that identifies the system to the mail recipient .
SMTP User Name
A name identifying the user to the SMTP mail server. The user name field can
include up to 10 alphanumeric characters and symbols (!, &, ? etc). Provision for
future functionality
SMTP Password
The password authenticating the user to the SMTP mail server. The password
can include up to 10 alphanumeric characters and symbols (!, &, ? etc). Provision
for future functionality
Controls
Allows to control timers related to operation with the GSM module.
Caller ID NO NO/YES
The Caller ID function enables to restrict SMS remote control operations to the
predefined follow me phone numbers. If the incoming number is recognized as
one of the Follow Me numbers, the operation will be executed.
Disable GSM NO NO/YES
YES: The system will disable the GSM/GPRS module from any activity.
NO: GSM/GPRS module is enabled in the system.

Page 104
Method: GSM
Parameter Default Range
CS via GPRS (out) YES NO/YES
YES: Enables to connect the panel to remote Configuration Software via the
GPRS channel. The connection can be established either from the LCD/Panda
keypad (Installer Menu > Activities > 7)CS Connect > 2)Via GPRS) or via SMS
request command from the Configuration Software.
NO: Communication between the Configuration Software and the panel via
GPRS is disabled
CS via GPRS (Listener mode) NO NO/YES
YES: The installed GSM/GPRS communication module enters into listener
mode. Configuration Software can then initiate connection to it.
Note: When using the polling feature through GPRS the MS channel parameter must be defined
as GPRS only.
The report code for MS polling is 999 (Contact ID) or ZZ (SIA)
The listening mode feature in the GSM/GPRS module can occur only if there is a static IP
address for the SIM card (Please consult the local telecommunication provider).

NO: The installed GSM/GPRS communication module will not enter into
listener mode and therefore Configuration Software cannot initiate connection to
it.
CS via CSD YES NO/YES
YES: Configuration Software can attempt to contact the panel through the GSM
CSD channel.
NO: Configuration Software cannot attempt to contact the panel through the
GSM CSD channel.
Parameters
Allows to program timers related to the operation with the GSM module.
SIM PIN Code
The PIN (Personal Identity Number) code is a 4 to 8 digit number giving you
access to the GSM network provider.
Note: You can cancel the PIN code request function by inserting the SIM card into a regular
mobile phone and according to the phone settings, disable this function.

SMS Center Phone

A telephone number of the message delivery center. This number can be
obtained from the network operator.
GSM Network Sensitivity (RSSI)
Set the minimum acceptable network signal level (RSSI level).
Options: Disabled (No troubles for low signal reception) / Low signal / High

Page 105
Method: GSM
Parameter Default Range
signal
SIM Number
The SIM phone number. The system uses this parameter to receive the time from
the GSM network in order to update the system time.
Prepaid SIM Card
Allows programming parameters that will be used when a prepaid SIM card is used in
the system.
Get Credit by
Depending on the local network provider, the user can receive the credit level of the
prepaid SIM card by sending a predefined SMS command to a defined number or by
calling a predefined number through the voice channel. The activation of the credit
request can be done by the Grand Master.
 SMS Credit Message: Type in the message command as defined by the
provider and the provider’s phone number to which the credit level SMS
message request will be sent.
 Voice Credit: Type in the provider’s phone number to which a call will be
established
 Service Command: Type in the service command message as defined by the
provider
Phone to Get Credit Message
The provider’s phone number to which the credit level SMS message request
will be sent to or a call will be established, depending on the selection in the
Get Credit by parameter.
Phone to Receive SMS Credit Message:
The provider’s telephone number from which an automatic SMS credit status
message will be sent from.

4.1.3 IP

Method: IP
Parameter Default Range
IP Configuration
Obtain Automatic IP YES Y/N
Defines whether the IP address, which the Agility 4 refers to, is static or dynamic.
YES: The system refers to an IP address provided by the DHCP.
NO: The system refers to a static IP Address.
Panel IP
The Agility 4’s IP address.

Page 106
Method: IP
Parameter Default Range
Subnet Mask
The subnet mask is used to determine where the network number in an IP
address ends.
Gateway
The IP address of the local Gateway, which enables communication settings to
other LAN segments. This address is the IP address of the router connected to
the same LAN segment as the Agility 4.
DNS Primary
The IP address of the primary DNS server on the network.
DNS Secondary
The IP address of the secondary DNS server on the network
Scan WiFi Net
The Control panel scans for Wi-Fi networks and shortly after available
networks appear in a list (the connected network is marked and appears first in
the list). The rest of the list is sorted from high RSSI to low, with a max. 20
networks.
Scroll to your Router’s Wi-Fi network, select the desired network and then
press [enter].
Enter the Password, if required, and press [enter]. If connection is successful, a
successful message is displayed. If there is a connection failure, an error message
is displayed
Add WiFi Net
Add Wi-Fi Network
WPS (Button)
Press the WPS button on the router to establish a connection and then press the
WPS button on the panel within 2 min.
A “Successfully Connected” to network message will appear.
E-mail
Allows programming parameters that enable the Agility 4 to send e-mail messages
following Follow Me events
Mail Host
The IP address or the Host name of the mail server.
SMTP Port
The port address of the SMTP mail server. Default: 00025
E-mail address

Page 107
Method: IP
Parameter Default Range
Agility 4’s e-mail address. Default: YourCompany.com
SMTP User name
If required by the mail server, fill in the Authentication User name

SMTP User password

If required by the mail server, fill in the Authentication User password
Host Name Security_System (Up to 32 characters)
IP address or a text name used to identify the Agility 4 over the network.
Default: Security System
MS Keep Alive (Polling) 00000 0-65535
The time period that the system will establish automatic communication (polling) with
the MS over the IP network, in order to check the connection. 3 polling times can be
defined: Primary, Secondary and Backup. For each time period define the number of
units between 1- 65535. Each unit represents a time frame of 10 seconds.
Note: When using the polling feature through IP, the MS channel parameter must be defined as IP only.

The use of these time periods depends on the reporting order to the MS defined by the
Report Split MS Urgent parameter (See: [4]Communication > [2]MS > [7]Report Split)
 Primary: This time period is used when the MS channel is defined as IP Only and the
Report Split parameter is not defined as 1st backup 2nd. Default: 00003 (30 seconds)
 Secondary: This time period is used when the MS 2 channel is defined as IPIP Only
and the Report Split parameter is defined as 1st backup 2nd. Default: 360 (3600 seconds)
 Backup: This time period will be assigned to the backup channel in the following case:

MS 2 channel is defined as IPIP Only

Report Split parameter is defined as 1st backup 2nd

The communication with MS 1 is disconnected.
Default: 00003 (30 seconds)
Controls
Disable IP NO YES/NO
YES: The system will disable the IP module from any activity.
NO: The IP module is enabled in the system.
CS via IP YES YES/NO
YES: The system allows access to Configuration Software through an IP
connection
NO: The system does not allow access to Configuration Software through an IP
connection

Page 108
4.2 Monitoring Station
The Monitoring Station sub-menu contains parameters that enable the system to establish
communication with the (up-to-three) monitoring stations and transmit data.
Communication: Monitoring Station
Parameter Default Range
Report Type
Type
Defines the communication type that the system will establish with each
monitoring station. The system can report in 4 optional communication types:
 Voice
 SMS
 IP
 SIA IP
Voice
Reports to the monitoring station will be done through the PSTN or GSM
network. Reporting by voice can be established through different
channels. The optional channels depend on the hardware installed in
your system. Select the required channel as follows:
 PSTN/GSM: The system checks for the availability of the PSTN
line. During regular operation mode all calls and data transmission
are carried out using the PSTN line. In the case of trouble in the
PSTN line, the line is routed to the GSM line.
 GSM/PSTN: The panel checks for the availability of the GSM line.
During regular operation mode all calls and data transmission are
carried out using the GSM line. In the case of trouble in the GSM
line, the line is routed to the PSTN line.
 PSTN Only: The outgoing calls are executed through the PSTN
audio channel only. Use this option for installations where no GSM
line is available.
 GSM Only: The outgoing calls are executed through the GSM audio
channel only. Use this option for installations where no PSTN line is
available.
Enter the monitoring station telephone number including area code and
special letters (if required). If calling from PBX do not include the
number for outgoing line.

Function Results
Stop dialing and wait for a new dial tone W
Wait a fixed period before continuing ,
Send the DTMF  character 

Page 109
Communication: Monitoring Station
Parameter Default Range
Send the DTMF # character #
Delete numbers from the cursor position [] [0] simultaneously
SMS
Events are sent to the monitoring station using encrypted SMS messages
(128 BIT AES encryption). Each event message contains information
including the account number, report code, communication format, time
of event and more. The event messages are received by RISCO Group's
IP Receiver Software located at the monitoring station site. The IP
Receiver translates the SMS messages to standard protocols used by the
monitoring station applications (For example; Contact ID). This channel
requires that RISCO Group’s IP receiver has to be used at the MS side.
Enter the relevant phone numbers for the MS that will receive reports
from the system (see explanation in the Voice type on page 109).
Note: An appropriate GSM/SMS transceiver must be connected to the same PC as an
IP Receiver.

IP
Encrypted events are sent to the monitoring station over the IP or GPRS
network using TCP/IP protocol. 128 BIT AES encryption is used. RISCO
Group's IP Receiver Software located at the monitoring station site
receives the messages and translates them to standard protocols used by
the monitoring station applications (For example; Contact ID).
Note: To enable GPRS communication the SIM card has to support GPRS channel

Reporting by IP can be established through different channels. The

optional channels depend on the hardware installed in your system.
Select the required channel via the Configuration Software as follows:
 IP/GPRS: The panel checks for the availability of the IP network.
During regular operation mode all calls and data transmission are
carried out using the IP network line. In the case of trouble in the IP
network, the report is routed to the GPRS network.
 GPRS/IP: The panel checks for the availability of the GPRS
network. During regular operation mode all calls and data
transmission are carried out using the GPRS. In the case of trouble
the report is routed to the IP network.
 IP Only: The report is executed through the IP network only.
 GPRS Only: The report is executed through the GPRS network.
Enter the relevant IP and Port numbers for the MS that will receive
reports from the system

Page 110
Communication: Monitoring Station
Parameter Default Range
SIA IP
Reports to the monitoring station can be transmitted using the SIA IP
protocol to standard SIA IP receivers. Using SIA IP enables transmission
of visual imagery from PIR cameras. Reporting by SIA IP can be
established through the hardware channels installed in your system.
Reporting of the SIA IP is 128 BIT AES encrypted. SIA IP reports also
support labels reporting. Usage of SIA IP requires setting:
 Encryption Key (see page 113)
 SIA IP Receiver Number
 SIA IP Receiver Line Number
Accounts
Account Number
The number that recognizes the customer at the monitoring station. You can
define an account number for each monitoring station. These account numbers are
the 6-digit numbers assigned by the central station.
Notes for Account Number in Contact ID Communication Format:
1. The account number will always be reported as 4 digits, for example: A number
defined as 000012 will be reported as 0012
2. If more than 4 digits were defined, the system always sends the last 4 digits of the
account number, for example: Account number that was defined as 123456 will be sent
as 3456.
3. In Contact ID you can place digits and letters A-F. The A character is always sent as 0
for example: Account number that was defined as 00C2AB will be sent as C20B.
Notes for Account Number in SIA Communication Format:
1. Account number for SIA should be defined as a decimal number (Only digits 0..9)
2. Account number can be reported as 1 to 6 digits. To send an account number with less
than 6 digits use the “0” digit, for example: For account number 1234 enter 001234. In
this case the system will not send the “0” digit to the monitoring station.
3. In order to send the “0” digit in SIA format, located at the left side of the number, use
the “A” digit instead of the “0” digit. For example, for account number 0407 enter
00A407, for a 6 digit account number such as 001207 enter AA1207.

Page 111
Communication: Monitoring Station
Parameter Default Range
Communications Format
Enables the system to contact the monitoring station in order to obtain details of
the communication protocol used by the digital receiver for each account.
The codes are automatically uploaded when the communication format has been
selected:
 Contact ID: The system allocates Report Codes supporting ADEMCO Contact
(Point) ID
 SIA: The system allocates Report Codes supporting the SIA (Security Industry
Association) format
Note: See Appendix A on page 138 for the report codes list.

Controls
Allows to program control related to operation with the Monitoring Station.
Handshake NO YES/NO
YES: All LEDs on the Agility 4 main panel light for one second when the
handshake signal is received from the monitoring station’s receiver.
NO: No indication for establishing communication with the monitoring station’s
receiver.
Kiss-Off Y/N NO YES/NO
YES: All LEDs on the Agility 4 main panel light for one second and an audible
sound is emitted when the kissoff signal is received from the monitoring station’s
receiver.
NO: No indication for establishing communication with the monitoring station’s
receiver.
SIA Text No
YES: SIA formatted report to the monitoring station will support text
transmission over the voice channel.
Note: The monitoring station receiver should support the SIA Text protocol.

NO: The SIA formatted report will not support text.

SIA IP + SN N
Select whether or not to add the panel’s serial number (for sending events with
images to the monitoring station software) via SIA IP protocol
SIA with Partition
Indicates the partition when reporting to the monitoring station in SIA over the
voice channel (PSTN or GSM).

Page 112
Communication: Monitoring Station
Parameter Default Range
Random MS Test
YES: At First power up the system will set a random hour which then becomes
the fixed hour for the panel to report periodic testing to the Monitoring Station.
This time can be viewed under the Periodic test timer fields.
NO: The periodic test will be according to the time defined by the installer
defined under the MS periodic timer
Parameters
Allows to program parameters related to operation with the Monitoring Station.
MS Retries 08 01-15
The number of times the system redials the Monitoring Station after failing to
establish communication.
Alarm Restore BTO
Specifies under what conditions an Alarm Restoral is reported. This option
informs the MS of a change in the specified condition(s) during an alarm restore.
These reports need a valid Report Code.
 On Bell Time Out (BTO) - Reports the restoral after the audible alarm times
out.
 Follow Zone - Reports the restoral when the zone in which the alarm occurs
returns to its non-violated (secured) state.
 At Disarm - Reports the restoral when the system (or the partition in which
the alarm occurs) is disarmed, even if the siren has already timed out.
Encryption Key
A 32-digit digital signature and authentication for purposes of safeguarding data
transmission to and from the monitoring station. The key must be defined for both
the panel and monitoring station. For use when SIA IP report type is in effect. A
unique key can be defined for each of up to three monitoring stations.
Receiver Number
A 4 digit number which states the SIA IP receiver number as supplied from the
monitoring station. A unique key can be defined for each of up to three monitoring
stations.
Line Number
A 4 digit number which states the SIA IP receiver line number as supplied from the
monitoring station. A unique key can be defined for each of up to three monitoring
stations.
MS Timers
Allows to program timers related to operation with the monitoring station.

Page 113
Communication: Monitoring Station
Parameter Default Range
Periodic Test
The Periodic Test enables you to set the time period that the system will
automatically establish communication to the Monitoring Station in order to
check the connection. The periodic test involves sending the account number and
a valid test report code (Contact ID 602, SIA TX). Set the test time and daily
interval for Periodic Test Reporting.
Abort Alarm 15 sec 0-255 sec
Defines the time delay before reporting an alarm to the MS. If the alarm system is
disarmed within the Abort Window, no alarm transmission shall be sent to the
MS.
Cancel Delay 5 min 0-255 min
If an alarm is sent in error, it is possible for the MS to receive a Cancel Alarm
Code, sent subsequently to the initial Alarm Code. This happens if a valid User
Code is entered to reset the alarm in the Cancel Delay time window that starts
after the defined Abort Alarm time is over.
Note: Cancel Alarm report code should be defined.

Listen In 120 1-240 seconds

The time duration for the monitoring station to Listen in and perform voice alarm
verification. After this period the system hangs up the line.
The monitoring station can expand the listen in time during the conversation by
pressing the digit "1" on the telephone. In this case, the Listen In time will reset
and start over again.
Confirmation
The confirmation times relate to the Zone Sequential Confirmation.
Confirm Start (Confirm 0 0-120 min
delay time)
Specifies that the system cannot start a sequential confirmation process
until the timer has expired. This time starts when the system has set and
will prevent confirmed alarms being generated in situations when a
person has been accidentally locked in the building.
Confirm Time Window 030 30-60 min
Specifies a time period that starts when an alarm is triggered for the first
time. If a second alarm is triggered before the end of the confirmation
time window, the system will send a confirmed alarm to the monitoring
station.

Page 114
Communication: Monitoring Station
Parameter Default Range
No Arm 0 0-12 weeks
A No Arm code will be sent to the MS if no arming or disarming has been
established during the time defined (1-12 weeks).
(0=not activated)
Report Split
The Report Split menu contains parameters that enable the routing of specified events to
up to three MS Receivers. See Appendix A on page 138.
MS Arm/Disarm
Reports Arming/Disarming (meaning Closings/Openings) events to the MS
 Do not call (no report)
 Call 1st: Reports Openings and Closings to MS 1
 Call 2nd: Reports Openings and Closings to MS 2
 Call 3rd: Reports Openings and Closings to MS 3
 Call all: Reports Openings and Closings to the all defined MS.
 1st Backup 2nd: Reports Openings and Closings to MS 1. If communication is
not established, calls MS 2.
MS Urgent
Reports urgent (alarm) events to the Central Monitoring Station
 Do not call (no report)
 Call 1st: Reports urgent events to MS 1
 Call 2nd: Reports urgent events to MS 2
 Call 3rd: Reports urgent events to MS 3
 Call all: Reports urgent events to the all defined MS.
 1st Backup 2nd: Reports urgent events to MS 1. If communication is not
established, calls MS 2
MS Non Urgent
Reports non-urgent events (troubles and test reports) to the MS
 Do not call (no report)
 Call 1st: Reports non-urgent events to MS 1
 Call 2nd: Reports non-urgent events to MS 2
 Call 3rd: Reports non-urgent events to MS 3
 Call all: Reports non-urgent events to the all defined MS.
 1st Backup 2nd: Reports non-urgent events to MS 1. If communication is not
established, calls MS 2

Page 115
Communication: Monitoring Station
Parameter Default Range
Report Codes
Enables you to view or program the codes transmitted by the system to report events (for
example, alarms, troubles, restores, supervisory tests, and so on) to the monitoring station.
The codes specified for each type of event transmission are a function of the Central
Station's own policies. Before programming any codes, it is important to check the Central
Station protocols. Reporting codes are assigned by default, according to the selected
communication format SIA or Contact ID
Assigns a specified report code for each event, based on the reporting format to the
monitoring station. An event that is not assigned with a report code will not be reported to
the monitoring station. For list of report events see Appendix A on page 138.

4.3 Configuration Software

The Configuration Software sub-menu contains parameters that enable the Configuration
Software to establish connection with the system.
Communication: Configuration software
Parameter Default Range
Security
Enables you to set parameters for remote communication between the technician and the
system using the Configuration Software
Access Code 5678
Enables you to define an access code that is stored in the system.
RISCO Group recommends using a different 4-digit access code for each
installation.
In order to enable communication between the alarm company and the system
the same access code must subsequently be entered into the corresponding
account profile created for the installation in the Configuration Software
For successful communication, the access code along with the ID code must
match between the Configuration Software and the system.

Page 116
Communication: Configuration software
Parameter Default Range
Remote ID 0001
Defines an ID Code that serves as an extension of the access code.
In order to enable communication between the alarm company and the
Installation, the same Remote ID code must be entered into the account profile
in the Configuration Software.
For successful communication, the ID Code along with the access code must
match between the Upload/Download software and the main panel.
Dealers often use the customer's monitoring station account number for the
ID Code, but you can use any 4-digit code unique to the installation
MS Lock 000000
MS Lock is a security function used in conjunction with the Configuration
Software. It provides greater proprietary security when viewing Monitoring
Station parameters.
The same 6-digit code, which will be stored in the panel, must be entered into
the corresponding account profile created for the installation in the
Configuration software.
If there is no match between the MS Lock Code defined in the main panel and
the MS Lock Code defined in the Configuration software, the installer will not
have permission to change the following Monitoring Station parameters from
the Configuration software:
MS Lock, Installer Code, MS IP Port, MS IP Address, MS Phone, Default Enable,
MS Account, MS Format, MS Channel, MS Backup, MS Enable, Remote ID,
Access Code.
Call Back
Call Back Enabled YES
The call back feature requires the system to call back to a pre-programmed
telephone number to which the alarm company's Configuration Software
computer is installed. This provides more security for remote operations using
the Configuration Software.
YES: Call back is enabled
NO: Call back is disabled

Page 117
Communication: Configuration software
Parameter Default Range
Call Back Phones
Define 3 numbers that the panel can call to perform Configuration Software
communication. If no numbers have been defined, a call back can be performed
to any phone. The installer will enter a phone number when establishing
communication to the panel. If at least one number has been defined, it will be
the only number that the call back can be established too. When the
Configuration Software establishes communication to the panel, it sends the
panel its calling phone number. (This number needs to be defined as My Number
under the GSM and PSTN Communication menu in the Configuration
Software). If the panel identifies one of the numbers as one of the numbers
predefined in the panel, the call will hang up and the panel will call back to that
same number.
Configuration Software IP Gateway

Note: In the Configuration Software, under Communication ConfigurationGPRS you should enter
the IP address of the PC that the software is installed in.

4.4 Follow-Me
In addition to reporting to the monitoring station, the Agility 4 has a Follow-Me feature
which enables reporting a system events to predefined destinations using a voice message,
SMS message or e-mail. Up to 16 Follow Me destinations can be defined in the system.
NOTE: The actual destinations (telephone numbers, email addresses) are defined outside
of the Installer Programming menu, or can be done from the User menus by the Grand
Master.
NOTE: Additional Follow-Me (known as “Follower”) e-mail notifications can be assigned
in the RISCO Cloud.

Page 118
Define FM

Communication: Follow-Me
Parameter Default Range
Label (via the Configuration Software)
A label identifying the follow me destination
Report Type
Defines the type of reporting events to a follow me destination:
 Voice: Report to follow me will be done by voice message thorough the
PSTN or GSM network. (See Channel For Voice Messaging below). Type in
the telephone number including area code or special letters for Follow Me
defined as SMS or Voice.
 SMS: Report to follow me will be done by SMS. Each event message contains
information including the system label. Event type and time. Type in the
telephone number including area code or special letters for Follow Me
defined as SMS or Voice.
 E-mail: Report to follow me will be done by e-mail thorough IP or GPRS.
Each e-mail contains information including the system label. Event type and
time. (See Channel For E-mail report below). Enter the e-mail address for
Follow Me destination defined as e-mail type.
Channel
Reporting events by Voice or Email can be established through different channels. The
optional channels depend on the hardware installed in the system. Select the required
channel as follows:
For Voice Messaging:
PSTN/GSM: The system checks for the availability of the PSTN line. During
regular operation mode voice messaging is carried out using the PSTN line. In
the case of trouble in the PSTN line, the line is routed to the GSM line.
GSM/PSTN: The panel checks for the availability of the GSM line. During
regular operation mode voice messaging is carried out using the GSM line. In the
case of trouble in the GSM line, the line is routed to the PSTN line.
PSTN Only: The outgoing calls are executed through the PSTN audio channel
only. Use this option for installations where no GSM line is available.
GSM Only: The outgoing calls are executed through the GSM audio channel
only. Use this option for installations where no PSTN line is available.

Page 119
Communication: Follow-Me
Parameter Default Range
For E-mail report:
IP/GPRS: The system checks for the availability of the IP network. During
regular operation emails will be sent using the IP network line. In the case of
trouble in the IP network, the email is routed to the GPRS network.
GPRS/IP: The system checks for the availability of the GPRS network. During
regular operation mode emails will be sent using the GPRS. In the case of trouble
the email is routed to the IP network.
IP Only: The report is executed through the IP network only.
GPRS Only: The report is executed through the GPRS network
Events
Each Follow Me destination can receive its own set of event notifications. Choose the
events that will be reported to each Follow Me destination.
Event Description Default
Alarms
Intruder Intruder alarm in the system Yes
Fire Fire alarm in the system Yes
Emergency Emergency alarm in the system Yes
Panic (S.O.S) A panic alarm in the system Yes
Tamper Any tamper alarm in the system No
Duress Alarm Duress alarm in the system from user xx Yes
No Movement No movement report indication No
Arm/Disarm
Arm Arming operation has been performed in the system No
Disarm Disarming operation has been performed in the system No
Parent Control System armed/disarmed by user/remote control defined No
with the Parent control feature
Troubles
False Code After 5 unsuccessful attempts of entering an incorrect No
code.
Main Low Battery Low battery indication from the Agility 4 main panel No
(below 6V)
Wireless Low Low battery indication from any wireless device in the No
Battery system
WL Jamming Jamming indication in the system No

Page 120
Communication: Follow-Me
Parameter Default Range
WL Lost Wireless device lost. When no supervision signal is No
received from a wireless device
AC Off Interruption in the source of the main AC power. This No
activation will follow the delay time predefined in the
AC Loss Delay timer
PSTN Trouble PSTN lost event. If PSTN Loss Delay time period is No
defined, the message will be sent after the delay time
IP Network Communication trouble with the IP network. No
GSM
GSM Trouble General GSM trouble (SIM card fault, Network No
availability, Network Quality, PIN code error, Module
communication, GPRS password, GPRS IP fault, GPRS
Connection, PUK code fault
SIM Trouble Any trouble with the SIM card No
SIM Expire Report to Follow Me will be established 30 days before No
the SIM Expiration Time defined for a prepaid SIM card.
SIM Credit An automatic SMS credit message (or any other No
message) received from the provider’s number
predefined in SMS Receive Phone will be transferred to
the Follow Me number
Environmental
Gas Alert Gas (natural gas) alert from a zone defined a Gas Yes
detector
Flood Alert Flood alert from a zone defined as flood type Yes
CO Alert CO (Carbon Monoxide) alert from a zone defined a CO Yes
detector
High High Temperature alert from a zone defined a Yes
Temperature Temperature detector
Low Temperature Low Temperature alert from a zone defined a Yes
Temperature detector
Technical Alert from the zone defined as Technical No

Page 121
Communication: Follow-Me
Parameter Default Range
Miscellaneous
Zone Bypass Zone has been bypassed No
Periodic test Follow Me test message will be established following No
the time defined in the Periodic Test parameter under
the MS parameters
Remote System is in remote installation mode No
programming
Communication The following information is sent by e-mail on power up No
Info and acquiring the GPRS and Ethernet communication
parameters (Assumption is that SMTP is predefined):
 Panel UID
 Panel version
 Ethernet IP parameters
 GPRS IP parameters
Restore Events:
Alarms
Intruder Alarm Intruder alarm in the system restored Yes
Tamper Tamper alarm in the system restored No
Troubles
Main Low Battery Low battery indication from the Agility 4 main panel No
restored
WL Low Battery Low battery indication from any wireless device in the No
system restored
Jamming Jamming indication in the system restored No
WL Lost Wireless device lost restored No
AC Off Interruption in the source of the main AC power No
restored
PSTN Trouble PSTN lost event restored No
IP Network Communication trouble in the IP restored No
GSM Trouble General GSM trouble restored No
Environmental
Gas Alert Gas Alert restored No
Flood Alert Flood Alert restored No
CO Alert CO Alert restored No

Page 122
Communication: Follow-Me
Parameter Default Range
High High Temperature Alert restored No
Temperature
Low Temperature Low Temperature Alert restored No
Technical Technical alert restored No
Remote Control
Remote Listen No
Enables the user of the follow me phone to perform remote listen and talk
operation with the premises.
Remote program No
Enables the user of the follow me phone to enter the Remote Operation menu
and perform all available programming options.
Partition
Assign the partitions from which events will be reported to the follow me number.

Controls
Allows to program control related to operation with the Follow Me
Disarm Stop Follow Me Yes Yes/No
YES: The Follow-Me calls will stop when the partitions are disarmed by a user
code
NO: The Follow-Me calls will continue to be made when the partitions are
disarmed by a user code

Parameters
Allows to program parameters related to operation with the Follow Me
Follow Me Retries 08 01-15
The number of times the Follow Me phone number is redialed
Voice Message Recurrence 01 01-05
This number of times a voice message repeats itself when establishing a call to a
Follow Me number.
Follow Me Periodic Test
The Periodic Test enables you to set the time period that the system will
automatically establish communication to a Follow Me destination defined with
the Periodic Test event.

Page 123
4.5 Cloud
You can define the server settings for Cloud communication with the Agility 4 system.
Communication: Cloud
Parameter Default Range
IP Address
The IP address or server name. If the Agility 4 system is connected to the RISCO
Cloud for self-monitoring, then use: www.riscocloud.com. Otherwise enter the IP
address or name where the Cloud server is located.
IP Port 33000
The server port address.
Password AAAAAA Up to 6 characters
(case sensitive)
Specify the password for server access. This password should be identical to the
CP Password defined in the server under the Main Panel page definition.
Channel
Communication with the Cloud can be established through an IP or GPRS
channel, depending on your system installed hardware.
 IP Only— Communication to the Cloud through the IP network only
 GPRS Only— Communication to the Cloud through the GPRS network
only
 IP/GPRS— The panel checks for the availability of the IP network. By
default the primary communication channel to the Cloud is via IP
network. In the case of trouble in the IP network, the communication is
routed through the GPRS network as a backup. Later on, it will check
every 10 minutes when the primary communication channel is available
 GPRS/IP— The panel checks for the availability of the IP network. By
default the primary communication channel to the Cloud is via GPRS
network. In the case of trouble in the IP network, the communication is
routed through the IP network as a backup. Later on, it will check every
10 minutes when the primary communication channel is available.

Page 124
Communication: Cloud
Parameter Default Range
Controls
The Agility 4 supports parallel channel reporting (via PSTN, IP, GPRS SMS, or
voice) to both the monitoring station and FM when connected in Cloud mode.
Use this setting to decide if the panel reports events to the monitoring station or
follow-me in parallel to the report to the Cloud or only as a backup when the
communication between the Agility and the Cloud is not functioning.
Note: When the backup mode is functioning, the MS specifications are as defined
under MS menu (see Monitoring Station, page 109), MS report type, and Follow-
Me menu (see Follow-Me, page 118).
MS Call All N
Yes: Parallel reporting to the monitoring station can be established via both the
Cloud and non-Cloud channels.
No: Communication to the monitoring station via the non-Cloud channels can be
established only in backup mode (when the Cloud connection is down)
FM Call All N
Yes: Parallel reporting to the Follow Me destination can be established via both
the Cloud and non-Cloud channels.
No: Communication to the Follow Me destination via the non-Cloud channels can
be established only in backup mode (when Agility 4– Cloud connection is down)
App Arm Y
Enables controlling the App arm functionality (for full arm or partial arm) from
the Smartphone or Web interface applications.
Yes: Full arm and partial arm are enabled
No: Full arm and partial arm are disabled
App Disarm Y
Enables controlling the App disarm functionality (for full disarm) from the
Smartphone or Web interface applications.
Yes: Full disarm is enabled
No: Full disarm is disabled
App Exit Delay Y
Enables controlling the App Exit Delay functionality from the Smartphone or Web
interface applications.
Yes: Exit Delay is enabled
No: Exit Delay is disabled

Page 125
5. Programming: Audio Messages Menu

The Audio Messages menu is used to define voice message parameters. This menu is divided
into the following sub menus:
1. Assign Message
2. Local Message

5.1 Assign Message

The installer can assign a voice message to a zone, partition, output or macro. When an event
occurs this voice message will be heard accordingly.
Each message can be comprised of up to 4 words. Each word has been pre-recorded and
assigned a number. When comprising a message the installer will enter the number of each
word into the message sequence. The system recognizes the numbers and sounds the words
assigned to those numbers. For example: For the system to sound “Top Floor Guest
Bedroom”, the installer must enter the following sequence: 119 050 061 019.
The table in Appendix C:: Library Voice Messages displays the directory of the pre-recorded
programming descriptors, each is identified by a 3 digit number.

NOTE: The first five descriptors allow for customized words specific for the client’s needs.
The customized words can be recorded via the telephone. Each recording is 2 seconds long.

To assign a message:

1. Go to Programming  Audio Messages  Assign Message.

2. Select the relevant device and go to Define.
3. Enter the relevant descriptor numbers (see Appendix C: Library Voice Messages) and

press / .
4. Go to Play to hear the message.

5.2 Local Message

Upon event occurrence, the system can announce the security situation to occupants of the
premises by sounding a local announcement message. This announcement message can be
enabled or disabled, per event. Enable or disable each message announcement according to
your customer request.

Page 126
Audio Messages: Local Messages
Parameter Description Default
Intruder alarm Intruder alarm Yes
Fire alarm Fire alarm Yes
Emergency Emergency (medical) alarm Yes
Panic alarm Panic alarm Yes
Tamper alarm Tamper alarm Yes
Environmental Flood, Gas, CO or Temperature alert Yes
alert
Away arm System/Partition armed in Away(Full arm) Yes
Stay arm System/Partition armed in Stay(Part set arm) Yes
Disarm System/Partition disarmed Yes
Audible Status Status heard when clicking the status button on the Yes
keypad/remote control
Entry / Exit System in entry or exit delay Yes
Auto arm System in auto arm process Yes
Output On/Off Output activated or deactivated (Outputs defined as No
Follow Code)
Walk test Walk test. The Agility 4 will sound the zone number Yes
and description
No Movement No movement message Yes
Miscellaneous Chime status and Macro messages Yes

Testing menu
The following menu is used to perform tests on the system. Note that each test refers to the
last time the device was activated. Tests can be performed on the following elements:

1. Main Unit
2. Zone
3. Keyfob
4. Keypad
5. Siren
6. GSM
7. IP Unit
8. UO Unit

Page 127
1. Main Unit

Main Unit
Parameter
Noise Level

From an LCD/Panda keypad, you can measure (“calibrate”) the background noise level
(RF interference) that the main panel detects, and also define (“view/edit”) the
acceptable threshold value, according to customer requirements. Measuring the noise
level provides an indication whether the main panel is mounted at a good location, and
defining the threshold value enables you to determine how much background noise the
system will tolerate before it generates jamming events.

To measure the background noise level detected at the main panel:

 Select Calibrate; the detected background noise level displays. If the resulting
value is far from your defined threshold value, or if the value is too high and you
believe the source of background noise may inherent to the main panel’s location,
you should move the main panel to a better location. See Comm Test, on the
following page for an explanation of acceptable results.

To define the system’s acceptable noise level threshold value:

 Select View/Edit, enter the threshold value (between 00 –99), and then

press / . The higher the number you set for the threshold value, the more
“sensitive” the system will be in generating jamming events (more frequently). The
lower the number set for the threshold value, the “more tolerant” the system will
be in generating jamming events (less frequently). See Comm Test, on the following
page for an explanation of acceptable results.

Siren
Activates the main unit siren.
Speaker
Sounds the local test message: “Test message”. Select Start to activate the feature. Select
Stop to end the test.
Battery
Displays the battery voltage of the main unit.
Version
Displays the main unit's software version.
Serial Number
Displays the main unit's serial number.

Page 128
2. Zone

Zone
Parameter
Comm Test
The Communication test displays the results of the signal strength measured at the panel
after the last device transmission (last detection or last supervision signal).
Make sure to activate the detector prior to the test.

For successful communication:

1) The signal strength (the Comm. test result) should be at least 30% (30 or more must
display).
2) In addition, the Comm. test result must be at least 10% higher than the result obtained
when performing the procedure to measure (“calibrate”) the background noise level
that the panel detects. For example, if the noise level measures 25%, the Comm. test
result must be 35% or more.
Battery Test
For the selected zone or device, displays the results of the last battery test performed
after the last transmission. An OK message is displayed for a successful test. For an
updated battery test result, activate the device before testing.
Walk Test
Used to easily test and evaluate the operation of selected zones in your system. It is
recommended to perform walk test after installing and allocating all wireless devices
and also prior to performing system operation.
The keypad LCD/Panda displays the following information for example:

Zone number; TRIP: (Successful detection); TMP: (Tamper detection) and Trb (Low
battery)
Version
This menu displays software version of the selected 2-way detector.

Page 129
3. Keyfob

Keyfob
Parameter Default Range
Comm Test
The Communication test displays the results of the signal strength measured at the panel
after the last device transmission (last detection or last supervision signal).
For successful communication:
1) The signal strength (the Comm. test result) should be at least 30% (30 or more must
display).
2) In addition, the Comm. test result must be at least 10% higher than the result obtained
when performing the procedure to measure (“calibrate”) the background noise level that
the panel detects. For example, if the noise level measures 25%, the Comm. test result
must be 35% or more.
Battery Test
Displays the results of the last battery test performed after the last transmission. OK
message is displayed for a successful test. For an updated value activate the device.
Version
This menu displays information regarding the 2-way remote control's version.

4. Keypad

Keypad
Parameter Default Range
Comm Test
The Communication test displays the results of the signal strength measured at the panel
after the last device transmission (last detection or last supervision signal).
Make sure to activate the device prior to the test.
For successful communication:
1) The signal strength (the Comm. test result) should be at least 30% (30 or more must
display).
2) In addition, the Comm. test result must be at least 10% higher than the result obtained
when performing the procedure to measure (“calibrate”) the background noise level that
the panel detects. For example, if the noise level measures 25%, the Comm. test result
must be 35% or more.
Battery Test
Displays the results of the last battery test performed after the last transmission. OK
message is displayed for a successful test. For an updated value activate the device.
Version

Page 130
Keypad
Parameter Default Range
This menu displays information regarding the keypad's version.

5. Siren

Siren
Parameter
Comm Test
The Communication test displays the results of the signal strength measured at the panel
after the last device transmission (last detection or last supervision signal).
Make sure to activate the device prior to the test.
For successful communication:
1) The signal strength (the Comm. test result) should be at least 30% (must display at
least 30 or more).
2) In addition, the Comm. test result must be at least 10% higher than the result obtained
when performing the procedure to measure (“calibrate”) the background noise level that
the panel detects. For example, if the noise level measures 25%, the Comm. test result
must be 35% or more.
Battery Test
Speaker batteries voltage: Tests the selected siren’s speaker batteries voltage.
Radio (Transceiver) batteries voltage: Tests the selected siren’s radio's batteries voltage.
Sound Test
Activates squawk sound in the selected siren.

Page 131
Siren
Parameter
Noise Level
This enables measuring (“calibrating”) and displaying the background (RF) noise as
measured at the siren, and also enables setting the noise level threshold – so that the
panel won’t cause jamming events as frequently if, for example, the siren is located
where there is an unusually high amount of background noise.

To calibrate (measure) the background noise at the siren:

1. At 4)Noise Level, press / , then scroll to the siren to measure and press

/ .

2. Scroll to Calibrate and then press / ; the result displays.

To define the noise level threshold value:

1. At 4)Noise Level, press / , then scroll to the siren to measure and press

/ .

2. Scroll to View/Edit and then press / .

3. Enter a new threshold level value (between 00—99), and press / . Keep
in mind the lower the number you set, the more “sensitive” the system will be
(generating jamming events more frequently), and the higher the number you set,
the more “tolerant” the system will be (generating jamming events less frequently).
Version
This menu displays information regarding the siren's version.

6. GSM
GSM
Parameter Default Range
Signal (RSSI)d (0–5)
Displays the signal level measured by the GSM module. (0=No signal, 5= Very high
signal)
Version
Displays information regarding the GSM card version.
IMEI

Page 132
GSM
Parameter Default Range
View the IMEI number of the GSM module. This number is used for identification of the
Agility 4 at the RISCO IP receiver when using GSM communication.
IP Address
The IP address given to the GSM when used in the Listener mode.
IMSI
International Mobile Subscriber Identity (IMSI) is a number that uniquely identifies
every user of a cellular network. It is stored as a 64-bit field and is sent by the mobile
device to the network.
ICCID
Integrated Circuit Card Identifier is a SIM card that contains its unique serial number
(ICCID). ICCIDs are stored in the SIM cards and are also printed on the SIM card during
a personalization process.

7. IP Unit
IP Unit
Parameter Default Range
IP Address
View the IP address of the Agility 4
Version
View the version on the IP card
MAC Address
View the MAC address of the IP card. This number is used for identification of the
Agility 4 at the RISCO IP Receiver when using IP communication.
WiFi MAC Address
View the Wi-Fi MAC address of the IP card. This number is used for identification of the
Agility 4 at the RISCO IP Receiver when using Wi-Fi communication.
WiFi test
View the received SSID (network name) and RSSI signal level: poor/fair/good/perfect.

8. UO Unit
UO Unit
Parameter Default Range
Comm Test

Page 133
UO Unit
Parameter Default Range
The Communication test displays the results of the last signal strength measurement
performed after the last device transmission (last detection or last supervision signal).
When performing a Comm. test, make sure to activate the device prior.
For successful communication:
1) The signal strength (the Comm. test result) should be at least 30% (must display at
least 30 or more).
2) In addition, the Comm. test result must be at least 10% higher than the result obtained
when performing the procedure to measure (“calibrate”) the background noise level that
the panel detects.
Battery Test
Displays the results of the last battery test performed after the last transmission. OK
message is displayed for a successful test. For an updated value activate the device.
Version
This menu displays information regarding the UO unit's version.

Activities Menu
The installer can perform special activities on the system via the Activities menu. Some of
these activities can also be performed by the user.
Activities
Parameter Default Range
Main Buzzer On/Off Off
Used to activate/deactivate the main unit buzzer.
KP Sleep Time 10 seconds 10-60 seconds
Used to set the keypad's Sleep mode time. (The LCD/Panda display is turned off.)
Service Mode
Grand masters and Installers can silence any tamper (and suppress a report to the
monitoring station) in the system from the main unit or any accessory for a period specified
in Service Time (see Service Time, page 45). Use this option, when system accessories require
battery replacement.
Avoid Report Programming
Some protocols have a report code to the monitoring station for entering and exiting the
installer programming. To avoid the entering report and save time, this function
postpones the report for two minutes during which the engineer can enter the
programming menu and no report will be made.
Bypass

Page 134
Activities
Parameter Default Range
Provides ability to bypass box tamper condition. When activated and tamper condition
occurs, there will be no alarm, no indication to the MS and no record in the event log.
Note: To enable Bypass Box Tamper, both the Allow Bypass and 24 Hour Bypass parameters must be set to
YES (refer to pages 45 and 48 respectively for more information).

Installer Reset
Use this option to reset an alarm.
Configuration Software Connect
Enables to establish remote communication with the Configuration Software at a
predefined location through IP or GPRS.
Note: The CS location should be predefined under CommunicationConfiguration SoftwareIP Gateway

Firmware Update
This option activates a firmware update process. The update can be established through
IP or GPRS. The location of the new firmware should be predefined under Installer
Programming SystemFirmware Update.
Once the communication method is selected (IP or GPRS) a special manufacturer
password should be entered. Please refer to your local RISCO branch for this password.
System Restart
Enables to restart the main panel via the keypad
Follow Me Menu
Follow Me
Parameter
Define
Used to define Follow Me destinations phone number or E-mail address according to its
type: Voice message, SMS or E-mail
Test FM
Used to test Follow Me reporting.

Clock Menu
Clock
Parameter Default Range
Time + Date
Allows the setting of the system time and date. This definition is required for setting the
scheduler programming in the system.

Page 135
Clock
Parameter Default Range
Scheduler On/Off
Enables you to activate or deactivate preprogrammed schedules that were defined by
your installer. Up to 8 weekly programs can be defined in the system during which the
system automatically arms / disarms or activates utility outputs.
Note: The definition of the scheduling programs is done from the Configuration Software.

Automatic Clock
Used to get an automatic time update (NTP or Daytime protocols) through the IP
network or GPRS.
Server
Select the Internet time protocol as NTP or Daytime
Host
The IP address or server name.
Port
The server port.
Time Zone (GMT/ UTC)

Use the / key to add an hour to the GMT/UTC time. Use the

/ key to subtract an hour from the GMT/UTC time.

Event Log Menu

Allows the viewing of significant system events including date and time. Scroll the list
using the arrow keys to view the events in the system.

Macro Menu
Programming Macro Keys
Agility 4 enables the installer or Grand Master to record a series of commands and assign
them to a macro. When the macro is pressed, the recorded commands are executed from
beginning to end. Up to 3 macros can be programmed to a system using the wireless
LCD/Panda keypad or the Agility 4 Configuration Software.
Before programming a macro, it is recommended to perform your required series of
commands, making a note of every key you press while doing so.

NOTE: Macros cannot be programmed to perform disarming commands.

NOTE: Macros cannot be activated from the Slim keypad.

Page 136
To program a macro:

1. In the Macro menu select a macro (A, B or C) and press .

2. Enter the sequence of characters according to the following table:
Key Description

Used to enter numerical characters

Used to move the cursor to the left

/
Used to move the cursor to the right
/
Press 1 twice Represents the  character
Press 3 twice Represents the  character
Press 4 twice Represents the key
Press 6 twice Represents the key
Press 7 twice Represents the  character
Press 9 twice Represents the # character

and 0 simultaneously Deletes your entry from the cursor position

forward
/ and 0 simultaneously

/ (LCD Keypad) / Use to toggle between / ///#/ and all of

the numeric characters
/ (Panda Keypad)

Used to end the sequence and save it to memory

/

3. Press / to save your entry. The series of characters is saved and assigned to
the selected macro. For example:

To arm partition 1 with the code 1234, enter the following sequence: 1 1234

Activating a Macro

Press 7/8/9 on the keypad for 2 seconds to activate the macro A/B/C respectively. A
confirmation message will be heard: "[Macro X] activated".

Page 137
Appendix A: Report Codes
Report Codes
Parameter Contact ID SIA Report
Category
Alarms
Panic alarm 120 PA Urgent
Panic alarm restore 120 PH Urgent
Fire alarm 115 FA Urgent
Fire alarm restore 115 Urgent
Medical alarm 100 MA Urgent
Medical alarm restore 100 MH Urgent
Duress alarm 121 HA Urgent
Duress alarm restore 121 HH Urgent
Box tamper 137 TA Urgent
Box tamper restore 137 TR Urgent
Confirmed alarm 139 BV Urgent
Confirmed alarm restore 139 Urgent
Recent Close 459 Non- urgent
Confirmed HU alarm (PD6662) 129 HV Urgent
Main Troubles
Low battery 302 YT Non- urgent
Low battery restore 302 YR Non- urgent
AC loss 301 AT Non- urgent
AC restore 301 AR Non- urgent
Clock not set 626 Non- urgent
Clock set 625 Non- urgent
False code 421 JA Non- urgent
False code restore 421 Non- urgent
Main phone trouble 351 LT Non- urgent
Main phone trouble restore 351 LR Non- urgent
RF Jamming 344 XQ Non- urgent
RF Jamming restore 344 XH Non- urgent
GSM trouble restore 330 IR Non- urgent
GSM Pre-Alarm Non- urgent

Page 138
Report Codes
Parameter Contact ID SIA Report
Category
IP Network trouble Non- urgent
IP Network trouble restore Non- urgent
Arm/Disarm
User Arm 401 CL Arm/Disarm
User Disarm 401 OP Arm/Disarm
Stay arm 441 CG Arm/Disarm
Disarm after alarm 458 OR Arm/Disarm
Keyswitch Arm 409 CS Arm/Disarm
Keyswitch Disarm 409 OS Arm/Disarm
Auto Arm 403 CA Arm/Disarm
Auto Disarm 403 OA Arm/Disarm
Remote Arm 407 CL Arm/Disarm
Remote Disarm 407 OP Arm/Disarm
Forced Arm 574 CF Arm/Disarm
Quick Arm 408 CL Arm/Disarm
No Arm 654 CD Arm/Disarm
Auto Arm fail 455 CI Arm/Disarm
Detectors(Zones)
Burglary alarm 130 BA Urgent
Burglary alarm restore 130 BH Urgent
Fire alarm 110 FA Urgent
Fire alarm restore 110 FH Urgent
Foil alarm 155 BA Urgent
Foil alarm restore 155 BH Urgent
Panic alarm 120 PA Urgent
Panic alarm restore 120 PH Urgent
Medical alarm 100 MA Urgent
Medical alarm restore 100 MH Urgent
24 Hour alarm 133 BA Urgent
24 Hour alarm restore 133 BH Urgent
Entry/Exit 134 BA Urgent
Entry/Exit restore 134 BH Urgent

Page 139
Report Codes
Parameter Contact ID SIA Report
Category
Water (Flood) alarm 154 WA Urgent
Water (Flood) alarm restore 154 WH Urgent
Gas alarm 151 GA Urgent
Gas alarm restore 151 GH Urgent
Carbon Monoxide alarm 162 GA Urgent
Carbon Monoxide alarm restore 162 GH Urgent
Environmental alarm 150 UA Urgent
Environmental alarm restore 150 UH Urgent
Low Temperature (Freeze alarm) 159 ZA Urgent
Low Temperature restore 159 ZH Urgent
High Temperature 158 KA Urgent
High Temperature restore 158 KH Urgent
Zone trouble 380 UT Urgent
Zone trouble restore 380 UJ Urgent
Burglary trouble 380 BT Urgent
Burglary trouble restore 380 BJ Urgent
Zone bypass 570 UB Urgent
Zone bypass restore 570 UU Urgent
Burglary bypass 573 BB Urgent
Burglary bypass restore 573 BU Urgent
Zone supervision loss 381 UT Urgent
Zone supervision restore 381 UJ Urgent
Tamper 144 TA Urgent
Tamper restore 144 TR Urgent
Zone lost 381 UT Urgent
Zone lost restore 381 UJ Urgent
Low battery 384 XT Non- urgent
Low battery restore 384 XR Non- urgent
Soak fail 380 UT Urgent
Soak fail restore 380 UJ Urgent
Zone Alarm 134 BA Urgent
Zone Alarm restore 134 BH Urgent

Page 140
Report Codes
Parameter Contact ID SIA Report
Category
Zone confirm alarm 139 BV Urgent
Zone confirm alarm restore 139 Urgent
No activity 393 NC Urgent
No activity restore 393 NS Urgent
Wireless Keypad
Tamper 145 TA Urgent
Tamper restore 145 TR Urgent
Low battery 384 XT Non- urgent
Low battery restore 384 XR Non- urgent
Wireless Keyfob
Arm 409 CS Arm/Disarm
Disarm 409 OS Arm/Disarm
Low battery 384 XT Non- urgent
Low battery restore 384 XR Non- urgent
Wireless Siren
Tamper 145 TA Urgent
Tamper restore 145 TR Urgent
Low battery 384 XT Non- urgent
Low battery restore 384 XR Non- urgent
Siren lost 355 BZ Urgent
Siren lost restore 355 Urgent
Wireless I/O Expander
Low battery 384 XT Non- urgent
Low battery restore 384 XR Non- urgent
I/O Expander lost 355 BZ Urgent
I/O Expander lost restore 355 Urgent
Tamper 145 TA Urgent
Tamper restore 145 TR Urgent
AC trouble 301 AT Non- urgent
AC trouble restore 301 AR Non- urgent
RF Jamming 380 XQ Urgent
RF Jamming restore 380 XH Urgent

Page 141
Report Codes
Parameter Contact ID SIA Report
Category
Miscellaneous
Enter programming (local) 627 LB Arm/Disarm
Exit programming (Local) 628 LS (LX ) Arm/Disarm
Enter programming (Remote) 627 RB Arm/Disarm
Exit programming (Remote) 628 RS Arm/Disarm
MS periodic test 602 RP Non- urgent
Call back 411 RB Non- urgent
System reset 305 RR Urgent
Abort Alarm 406 BC Urgent
Listen in begin 606 LF Urgent
MS keep alive (polling) 999 ZZ Urgent
Cancel Report 406 OC Urgent
Walk Test 607 BC Non- urgent
Walk Test restore 607 Non- urgent
Exit Error 374 Non- urgent
Enter Quick Learn 627 LB Urgent
Exit Quick Learn 628 LS Urgent
Enter Service Mode 393 LB Non- urgent
Exit Service Mode 393 LX Non- urgent
Finished Uploading Pictures Urgent
MS Trigger ZY Non- urgent
MS Trouble Non- urgent
Fail Cloud Communication Non- urgent

Page 142
Appendix B: Installer Event Log Messages
Event Message Description
Activate UO=xx UO XX activation
Actv UO=xx KF=zz UO XX is activated from remote control ZZ
AL.Reinstate P=y Alarm reinstatement on partition Y
Alarm abort P=y Alarm aborted on partition Y
* Alarm Zone=xx Alarm in zone no. XX
* Anti-code reset Remote reset
Auto Add GSM GSM Module added to the main unit
Auto Add IP card IP Module added to the main unit
Auto Add MODEM Modem added to the main unit
Auto Del GSM GSM Module was removed from the main unit
Auto Del IP card IP Module removed from the main unit
Auto Del MODEM Modem removed from the main unit
Auto test fail Failure of zone self-test
Auto test OK Automatic zone self-test OK
* Away fail P=y Partition Y failed to arm
* Away:P=y C=zz Partition Y armed by user no. ZZ
* Away:P=y KF=zz Partition Y armed by remote control ZZ
* Bell tamper Bell tamper alarm
Bell tamper rst Bell tamper alarm restore
* Box tamper Box tamper alarm from main unit
Box tamper rst Box tamper alarm restore
* Bypass Box+Bell Box + Bell tamper is bypassed
Bypass code=xx Bypass code XX has been used
* Bypass Trbl C=xx System troubles were bypassed by user XX
* Bypass Zone=xx Zone no. XX is bypassed
Cancel alarm event occurred from partition X. A valid user function
Cancel Alarm P=x
is entered to reset the alarm after the defined Abort alarm time
Change code=xx Changing user code XX
Change FM=yy Changing Follow-Me number YY
Change tag=xx Changing keypad tag for user XX
Clock not set Time is not set
Clock set C=xx Time defined by user no. XX
Cloud Connected " , Cloud communication channel is functioning
Cloud Disconnect" , // Cloud communication channel is not functioning
CO Alarm Zn=xx CO alert from zone XX defined as a CO detector
CO Rst. Zn=xx CO alert restored from zone XX defined as a CO detector
Com ok IP card Communication OK between the Agility 4 and IP card
Comm OK Siren=y Communication OK between the Agility 4 and Siren Y
Comm. OK GSM Communication OK between the Agility 4 and GSM

Page 143
Event Message Description
Comm.OK I/O Mdl. Communication OK between the Agility 4 and I/O module
Conf. alarm P=y Confirmed alarm occurred in partition Y
Conf. Hold-Up P=y Confirmed Hold-Up Alarm in partition Y
Confirm rs Z=xx Restore zone confirmed alarm
* Confirm Zone=xx Confirmed alarm occurred from zone XX
CP reset The main panel has reset
Date set C=xx Date defined by user no. XX
* Day Away:P=y Daily arm on partition Y
Day disarm:P=y Daily disarm on partition Y
* Day stay: P=y Daily STAY arming in partition Y
Device Tmpr Byp Device Tamper Bypass
* Disarm:P=y C=zz Partition Y disarmed by user ZZ
* Disarm: P=y KF=zz Partition Y disarmed by remote control ZZ
Duress C=xx Duress alarm from user no. XX
Entering installer programming from keypad or Configuration
Enter program
Software
Exit error event from zone XX
Exit Error Zn=xx
The zone was left open at the end of the exit time
Exiting installer programming from keypad or Configuration
Exit program
Software
False code False code alarm
False restore False code alarm restore
Fire Keypad=y Fire alarm from wireless keypad Y
Fire main KP Fire alarm from
Fire ok Zone=xx Trouble restore in fire zone no. XX
Fire trbl Zn=xx Trouble in fire zone no. XX
* Fire Zone=xx Fire alarm in zone no. XX
Foil ok Z=xx Restore in foil (Day) zone no. XX
Foil Zone=xx Trouble in foil (Day) zone no. XX
Forced P=y Partition Y is force armed
Found Zone=xx Wireless zone found, zone no. XX
* Gas Alarm Zn=xx Gas (natural gas) alert from zone XX defined as a gas detector
Gas (natural gas) alert restored from zone XX defined as a gas
Gas Rst. Zn=xx
detector
GSM:IP OK IP connection OK
GSM:IP Trouble IP address is incorrect
Communication between the GSM and the Agility 4 is OK
GSM:Mdl comm.OK
* GSM: Module comm. Internal GSM/GPRS BUS module trouble
* GSM:NET avail. GSM network is not available
GSM:NET avail.OK GSM Network is available
GSM:NET qual.OK GSM Network quality is acceptable

Page 144
Event Message Description
GSM:NET quality The GSM RSSI level is low
GSM:PIN code err PIN code entered is incorrect
GSM:PIN code OK PIN code is correct
GSM:PUK Code err PUK code required
GSM:PUK Code OK PUK Code entered is correct
GSM:SIM OK SIM Card in place
GSM:SIM trouble SIM card missing or not properly sited
High temperature alert restored from zone XX defined as a
H.Temp rst Zn=xx
temperature detector
High temperature alert from zone XX defined as a temperature
* High Temp. Zn=xx
detector
HU.Reinstate P =Y Hold-Up Reinstatement in partition y
I/O:AC Rstr AC power restore on I/O module
I/O:AC Trouble AC power trouble on I/O module
I/O: Battery Rstr I/O module battery trouble restored
* I/O: Battery Trbl I/O module battery trouble alert
* I/O: Jamming I/O module jamming alert
I/O: Jamming Rstr I/O module jamming alert restored
* I/O: Lost I/O module is regarded as lost following supervision test
* I/O: Tamper I/O module tamper alert
I/O: Tamper Rstr I/O module tamper alert restored
The Agility 4 received a signal from I/O module after it has been
IO: Lost Restore
regarded as lost
IPC:DHCP error Failed to acquire an IP address from the DHCP server
IPC:DHCP ok Succeeded to acquire an IP address from the DHCP server
* IPC: Network err Failed to connect to IP network
IPC: Network ok Successful connection to IP network
IPC:NTP error Failed to acquire time data from the time server
IPC:NTP ok Succeeded to acquire time data from the time server
Jamming OK Zn=xx Zone XX jamming OK
Jamming restore Wireless receiver jamming restore
* Jamming Z=xx Zone XX jamming trouble
KeyBox Open Z=xx Zone XX defined as KeyBox type is open
KeyBox Rst Z=xx Zone XX defined as KeyBox type is closed
KP=y Low Bat.Rst Low battery trouble restored from keypad Y
* KP=y Low Battery Low battery trouble from keypad Y
* Ksw away:P=y Partition Y is armed by key switch
* Ksw disarm:P=y Partition Y is disarmed by key switch
L.bat rstr KF=yy Low battery trouble restore from wireless remote control YY
Low temperature alert restored from zone XX defined as a
L.Temp rst Zn=xx
temperature detector

Page 145
Event Message Description
* Lost Zone=xx Wireless zone lost, zone no. XX
Low Bat rs Z=xx Low battery trouble restored from wireless zone no. XX
Low bat. Zn=xx Low battery trouble from wireless zone no. XX
Low bat.KF=yy Low battery trouble from wireless remote control XX
Low temperature alert from zone XX defined as a temperature
* Low Temp. Zn=xx
detector
Main:AC restore AC power restore on main panel
Main: Battery rst Low battery trouble restore from the main panel
Main: Low AC Loss of AC power from the main panel
Main: Low battery Low battery trouble from the main panel
* MS=y call error Communication fail trouble to MS phone no. Y
* MS=y restore Communication fail trouble restore to MS phone no. Y
* Msg Box Tamper Tamper alarm from the Listen In message box unit
Msg Box Tmp Rst. Tamper alarm restore from the Listen In message box unit
No Com IP card Communication failure between the Agility 4 and IP card
* No comm I/O Mdl. Communication failure between the Agility 4 and I/O module
* No comm Siren=y Communication failure between the Agility 4 and siren Y
* No comm. GSM No communication between GSM/GPRS module and the Agility 4
* Phone fail If the phone line is cut or the DC level is under 1V
Phone restore Phone line trouble restore
* Police Keypad=y Police (panic) alarm from wireless keypad Y
* Police KF=yy Police (panic) alarm from remote control YY
* Radio l.bat 5S=y Radio low battery trouble from siren Y
Radio l.bat rS=y Radio low battery restore from siren Y
* Remote away:P=y The system has been armed from the Configuration Software
* Remote program The system has been programmed from the Configuration Software
The system has been armed in STAY mode from the Configuration
* Remote stay:P=y
Software
Restore Zone=xx Alarm restore in zone no. XX
* RF Jamming Wireless receiver jamming
Rmt disarm:P=y Partition Y disarmed from the Configuration Software
* Siren=y Lost Siren Y is regarded as lost following supervision test
The Agility 4 received a signal from siren Y after it has been
Siren=y Lost Rst
regarded as lost
Soak fail Z=xx Zone XX has failed in the soak test
Special KP=y Special alarm from the from wireless keypad Y
Spkr l.bat rsS=y Speaker low battery restore from siren Y
* Spkr low bat S=y Speaker low battery trouble from siren Y
Start exit P=y Exit time started in partition Y
* Stay:P=y C=zz Partition Y stay armed by user ZZ
* Stay: P=y KF=zz Partition Y stay armed by remote control ZZ
* Tamper I/O Mdl. Tamper alarm from I/O module

Page 146
 Event Message Description
Tamper I/O Rst. Tamper alarm restored from I/O module
* Tamper Keypad=y Tamper alarm from keypad ID=Y
Tamper rs Zn=xx Tamper alarm restore on zone no. XX
Tamper rst KP=y Keypad Y tamper restore
* Tamper Siren=y Tamper alarm from wireless siren Y
* Tamper Zone=xx Tamper alarm from zone no. XX
* Tech alarm Zn=xx Alarm from zone XX defined as Technical
Tech rstr Zn=xx Alarm restored from zone XX defined as Technical
Tmp rstr Siren=y Tamper alarm restore from wireless siren Y
Unbyp Box+Bell Box + Bell reinstated from bypass
Unbypass Zone=xx Zone no. XX is reinstated from bypass
Unknown event Unknown event alert
User XX has entered into programming mode. User 99 represents
User login C=xx
remote programming from the Configuration Software
* Water Alrm Zn=xx Flood alarm from zone no. XX
Water rstr Zn=xx Flood alarm restore on zone no. XX
Z=xx auto bad Zone self-test failed, zone no. XX
Z=xx auto ok Zone self-test OK, zone no. XX
Zn=xx Trouble Zone trouble event from zone XX
Zn=xx Trouble OK Zone trouble event restore from zone XX

* Specifies which events will be written in the event log once the mandatory Event control
bit is selected (see page 52).

Page 147
Appendix C: Library Voice Messages
001 (Customized 1) E M 130 Store
002 (Customized 2) 046 East 087 Macro 131 Student room
003 (Customized 3) 047 Elevator 088 Magnet 132 Study
004 (Customized 4) 048 Emergency 089 Main T
005 (Customized 5) 049 Entrance 090 Master 133 Technical
A 050 Entry 091 Middle 134 Temperature
006 A 051 Executive 092 Motion 135 Third
007 Above 052 Exit N 136 To
008 Air conditioner 053 External 093 Near 137 Top
009 An F 094 New 138 TV
010 And 054 Family 095 North U
011 Apartment 055 Fence 096 Nursery 139 Under
012 Area 056 Fire O 140 Up
013 At 057 First 097 Of 141 Upstairs
014 Attic 058 Flood 098 Office V
B 059 Floor 099 On 142 Video camera
015 Baby's room 060 For 100 Outdoor W
016 Back 061 Foyer 101 Output 143 Wall
017 Balcony 062 Front 102 Outside 144 Warehouse
018 Basement G P 145 Washroom
019 Bathroom 063 Game 103 Panic 146 West
020 Bedroom 064 Garage 104 Partition 147 Window
021 Before 065 Garden 105 Passage Y
022 Behind 066 Gas 106 Patio 148 Yard
023 Bottom 067 Gate 107 Perimeter Z
024 Boy's room 068 Girl's room 108 Pool 149 Zone
025 By 069 Glass R Numbers
C 070 Guest 109 Rear 150 0
026 Camera H 110 Reception 151 1
027 Ceiling 071 Hallway 111 Refrigerator 152 2
028 Cellar 072 High 112 Relay 153 3
029 Central I 113 Right 154 4
030 Children 073 In 114 Roof 155 5
031 Cleaner 074 Indoor 115 Room 156 6
032 CO 075 Inside S 157 7
033 Computer room 076 Internal 116 Safe 158 8
034 Contact 077 Is 117 Safety 159 9
035 Control K 118 Second
036 Corner 078 Keyfob 119 Sensor
037 Curtain 079 Kitchen 120 Shock
D L 121 Shop
038 Desk 080 Landing 122 Shutter
039 Detector 081 Left 123 Side
040 Device 082 Library 124 Siren
041 Dining 083 Light 125 Site
042 Door 084 Living 126 Smoke
043 Down 085 Lobby 127 South
044 Downstairs 086 Low 128 Sprinkler
045 Dressing 129 Stairs

Page 148
Appendix D: Remote Firmware Upgrade
This appendix explains how to perform remote upgrade of your Agility 4 main panel
software using the Configuration Software. Remote software upgrade is performed via IP
or GPRS.

Prerequisites

 Agility 4 Configuration Software

 Agility 4 control panel version 4.76 and later
 Agility 4 system equipped with a GSM/GPRS or IP module

NOTE: Back up panel parameters into the Configuration Software before performing
software upgrade. With established connection to the Agility main panel:
Communication > Receive > All

Step 1: Verify the current version of your Agility 4 main panel

In order to later confirm that the upgrade procedure has been successful (step 4), take note
of the current version of your Agility 4 main panel software.
1. Login to the Agility 4 Configuration Software program.
2. Select a client.

3. Click Connect to establish connection to the Agility 4 main panel.

4. Go to the Activities  Testing screen.
5. In the Main Unit tab, click on the Test button. The current version of the main panel
appears in the Panel version textbox.

Page 149
Step 2: Enter the location of the upgrade file

System Screen (Basic Tab)

Page 150
System Screen (Advanced tab)

1. In the System screen, in the Main Unit Software Upgrade section, enter the relevant
information regarding the location of the upgrade file:
 Host: Enter the IP address of the router/gateway where the upgrade file is located.
Default: firmware.riscogroup.com
 Port: Enter the port on the router/gateway where the upgrade file is located.
Default: 80
 File Name: Enter the upgrade file name. For example:
/WirelessPanels/OEN/FAT.txt
Please contact Customer Support services for the file name parameters.

2. Click Send .

Page 151
Step 3: Perform upgrade

NOTE: Make sure you are online and connected to the Agility 4 control panel (if not, click
Connect ).

1. In the Activities  Main Unit Upgrade screen select the Upgrade Channel from two
options:
 Upgrade through IP
 Upgrade through GPRS
2. Click on the Upgrade… button. The following dialog box appears:

Page 152
3. The message that appears informs you that remote software upgrade may result in
returning the main panel to its default values, therefore it is recommended to backup
all client information before performing the upgrade.
4. Enter the Upgrade Security password and click Upgrade….
Please contact Customer Support services at your local RISCO Group branch for the
password.

NOTE: For users with Agility 4 Configuration Software, for some versions the
following message will appear: "The upgrade process will commence after
disconnecting this session."

5. Click OK.

6. Disconnect from the current session (Click Disconnect ) to begin the upgrade
procedure. The LEDs on the Agility 4 main panel will begin to flash during the
upgrade procedure as follows: The Power LED will light up and the other LEDs
will flash rapidly.

NOTE: If upgrade fails, the previous Agility 4 main panel software version is
automatically recovered.

Step 4: Restoration of panel-to-system communication

In the event that the firmware upgrade involved a database change, the panel resets all
parameters (except those for communication, as per the list below*). In this case, to
re-enable Agility 4-to- panel communication, reconnect to the panel from Configuration
Software and “Send All” parameters as follows:
Communication > Send > All
Consult RISCO technical support for further details.
* Saved communication parameters list:
a. System Parameters:
i. CS Enable
ii. FM Enable.
iii. MS Enable
iv. Cloud Enable
v. Disable incoming call
vi. Random periodic test
vii. SIA with text
viii. CS Call back
b. MS Parameters:
i. MS LOCK

Page 153
c. Configuration Software Parameters:
i. Access code
ii. Remote ID
iii. All the CS enable flags (PSTN, IP, GSM in, out, SCD).
1. CS via GPRS (out)
2. CS via GPRS (List)
3. CS via CSD
4. CS via IP
5. CS via Modem
d. Codes:
i. Installer code
ii. Sub installer code
iii. GM Code
e. GSM Parameters:
i. GSM APN code
ii. GSM APN user
iii. GSM APN password
iv. GSM PIN Code
f. IP Module Parameters:
i. IP Dynamic/Static
ii. IP Address
iii. IP Subnet
iv. IP Gateway
v. IP NetBIOS name
vi. IP DNS1
vii. IP DNS2
g. Cloud Parameters:
i. Cloud CHANNEL
ii. Cloud PASSWORDELAS PORT.
iii. Cloud IP

Page 154
Appendix E: Installer Programming Maps
Installer menu: Note: Programming menu is on page 156.
1) Programming
2) Testing
1) Main Unit
1) Noise Level 4) Battery
2) Siren 5) Version
3) Speaker 6) Serial Number
2) Zone
1) Communication Test 3) Walk Test
2) Battery Test 4) Version
3) Remote Control
1) Communication Test 3) Version
2) Battery Test
4) Keypad
1) Communication Test 3) Version
2) Battery Test
5) Siren
1) Communication Test 4) Noise Level
2) Battery Test 5) Version
3) Sound Test
6) GSM
1) Signal 3) IMEI
2) Version 4) IP Address
5) IMSI 6) ICCID
7) IP Unit
1) IP Address 4) WiFi Mac addr
2) Version 5) WiFi test
3) MAC Address
8) I/O Module
1) Communication Test 3) Version
2) Battery Test
3) Activities
1) Main Buzzer
2) KP Sleep Time
3) Service Mode
4) Avoid Report Prog
5) Bypass Box Tamp
6) Installer Reset
7) CS Connect
8) Firmware Update
9) System Restart
4) Follow Me
1) Define
2) Test Follow Me
5) Clock
1)Time and Date
2) Scheduler Enable
3) Auto. Clock
1) Server 3) Port

Page 155
 2) Host 4) Time Zone
6) Event Log
7) Macro
Programming menu:
1) System
1) Timers
1) Ex/En Delay 1
2) Ex/En Delay 2
3) Bell Timeout
4) Bell Delay
5) AC Off Delay
6) Jamming Time
7) RX Supervision
8) TX Supervision
9) Redial Wait
0) More
1)Swinger Shutdown
2) No Activity
3) Last Exit Sound
4) Entry Bypass
5) Service Time
2) Controls
1) Basic
Quick Arm
Allow Bypass
Quick Status
False Code Trouble
Siren Squawk
Audible Panic
Buzzer  Bell
Audible Jamming
Exit Beeps At Stay
Forced Arming
Arm Pre-Warning
Default Enable
Main But: Status/Talk
Quick Learn
2) Advanced
Area
Global Follower
Summer/Winter
24 Hour Bypass
Technician Tamper
Technician Reset
Installer Tamper
Low Battery Arm
Siren Pre-alarm
Bell 30/10
Fire Alarm Pattern
IMQ
Disable Incoming Call

Page 156
 Bypass Unique Code
Silent Remote Install
AntiMask
Power Management
Presence
Secondary Alarm
3) Communication
MS Enable
Configuration Software Enable
FM Enable
Cloud Enable
4) EN 50131
Authorize Installer
Override Trouble
Restore Alarm
Mandatory Events
Restore Troubles
Exit Alarm
Entry Alarm
20 Minutes Signal
Attenuation
5) PD6662 Prog
Bypass Exit/Entry
Entry Disable
Route Disable
Installer Confirmation
Keyswitch Lock
Entry Disarm
6) CP-01
Exit Restart
Auto Stay
Exit Error
3 Min. Bypass
3) Labels
1) System
2) Partition 1
3) Partition 2
4) Partition 3
4) Sounds
1) Tamper Sound
Silent
Bell
Buzzer (main)
Bell + Buzzer
Bell/A + Buzzer/D
Bell/A + S/Disarm
2) Local Alarm
3) Local Squawk
4) Ex/En Beeps
5) Speaker Volume

Page 157
 5) Settings
1) Default Panel
2) Erase WL Device
3) Language
4) Standards
EN 50131
PD6662
CP-01
5) Customer
6) Service Info
1) Service Name
2) Phone
7) Firmware Update
1) Server IP
2) Server Port
3) File Path
8) Picture Server
1) Server IP
2) Server Port
3) File Path
4) Username
5)Password
6) Image Channel
2) Radio Devices
1) Allocation
1) RF Allocation
2) By Serial code
3) Zone Allocation
2) Modification
1) Zones
1) Parameters
1) Label
2) Serial No.
3) Partition
4) Type
5) Sound
6) Advanced
1) Chime
2) Control
Supervision
Forced Arming
No Activity
LED Enable
Abort Alarm
Presence
3) Detection Mode
4) Sensitivity
5) Camera Parms
Images at Alarm

Page 158
 Image Interval
Image Pre-Alarm
Image Resolution
Image Quality
Colored Image
6) PIR Camera Triggers
6) X73/X78 Contact
Magnet
Alarm Hold On
Input Termination
Input Response Time
Shutter Pulse
7) Two-way Detector
Operation Mode
2) Alarm Confirmation
1) Confirm Partition
2) Confirm Zones
3) Soak Test
4) Cross Zones
2) Keyfobs
1) Parameters
1-Way Keyfob 2-Way Keyfob
1) Label 1) Label
2) Serial No. 2) Serial No.
3) Partition 3) Partition
4) Button 1 4) PIN Code
5) Button 2 5) Panic Enable
6) Button 3 6) UO Button 1
7) Button 4 7) UO Button 2
8) UO Button 3
2) Controls
Instant Arm
Instant Stay
Code Disarm
3) Parent Control
3) Keypads
1) Parameters 1) Label
2) Serial No.
3) Emergency Keys
4) Function Key (LCD/Panda Only)
5) UO Control
6) Mode (Slim only)
7) Door Bell Sound (Slim only)
8) Supervision
9) Auto Status
2) Controls
RF Wake-up
4) Sirens
1) Label
2) Serial Number
3) Partition

Page 159
 4) Supervision
5) Volume
1)Alarm
2) Squawk
3) Exit Entry
5) Strobe (Ext.l)
1)Strobe Ctrl
2) Strobe Blink
3)Strobe Arm Blink
5) I/O Modules
1) Wired Zones
1) Label
2) Partition
3) Type
4) Sound
5) Advanced
1) Chime
2) Control
3) Termination
4) Loop Response
5) Detection Mode
2) Outputs
1) Label
2) Type
3) Pattern
4) Pulse Length
3) X-10 Outputs
1) Label
2) Type
3) Pattern
4) Activation / Deactivation
5) Pulse Length
4) Parameters
1) Serial No.
2) Control
1) Supervision
2) Quick UO/X10
3) X10 House ID
4) UO DTMF Control
3) Identification
4) Delete

3) Codes
1) User
1) Label
2) Partition
3) Authority
User
Cleaner
Arm Only
Duress

Page 160
 Door Bypass
2) Grand Master
3) Installer
4) Sub-Installer
5) Code Length
4 Digits
6 Digits
6) DTMF Code
7) Parent Control
4) Communication
1) Method
1) PSTN
1) Timers
1) PSTN Lost Delay
2) Wait for Dial Tone
2) Controls
Alarm Line Cut
Answer Machine Override
CS via PSTN
3) Parameters
1) Rings to Answer
2) Area Code
3) PBX Prefix
2) GSM
1) Timers
1) GSM Lost
2) SIM Expire
3) MS Keep Alive
(Polling)
2) GPRS
1) APN Code
2) APN User Name
3) APN Password
3) Email
1) Mail Host
2) SMTP Port
3) E-mail Address
4) SMTP User Name
5) SMTP Password
4) Controls
Caller ID
Disable GSM
CS via GPRS (out)
CS via GPRS (Listener mode)
CS via CSD
5) Parameters
1) SIM PIN Code
2) SMS Center Phone
3) GSM RSSI
4) SIM Number
6) Pre-Paid SIM

Page 161
 1) Get Credit by
2)SMS Receive Phone
3) IP
1) IP Configuration
1) Obtain Auto IP
2) Panel IP
3) Subnet Mask
4) Gateway
5) DNS Primary
6) DNS Second
8) Scan WiFi Net
9) Add WiFi Net
10) WPS (Button)
2) E-mail
1) Mail Host
2) SMTP Port
3) E-mail Address
4) SMTP Name
5) SMTP Password
3) Host Name
4) MS Keep Alive
(Polling)
5) Controls
Disable IP CS via IP
2) Monitoring Station
1) Report Type
Voice
SMS
IP
SIA IP

2) Accounts
3) Comm Format
Contact ID
SIA
4) Controls
Handshake
Kissoff
SIA Text
SIA IP +SN
SIA with Partition
Random MS Test
5) Parameters
1) MS Retries
2) Alarm Restore
3) Encryption Key
4) Receive Number
5) Line Number
6) MS Timers
1) Periodic Test
2) Abort Alarm
3) Cancel Delay
4) Listen In

Page 162
 5) Confirmation
6) No Arm
7) Report Split
1) MS Arm/Disarm
2) MS Urgent
3) MS Non Urgent
8) Report Codes
1) Edit Codes
2) Delete All
3) Configuration s/w
1) Security
1) Access code
2) Remote ID
3) MS Lock
2) Call Back
Call Back Enabled
Call Back Phones
3) CS / IP Gateway
4) Follow-Me
1) Define
1) Report type
Voice
SMS
Email
2) Events
3) Restore events
4) Remote control
Remote listen
Remote program
5) Partition
2) Controls
Disarm stop FM
3) Parameters
1) FM Retries
2) Voice Mesg Rec
3) Periodic test
5) Cloud
1) IP Address
2) IP Port
3) Password
4) Channel
IP Only
GPRS Only
IP/GPRS
GPRS/IP
5) Controls
MS Call All
FM Call All
App Arm
App Disarm
App Exit Delay

Page 163
5) Audio
1) Assign Message
1) Zone
2) Partition
3) Output
4) X10 output
5) Macro
2) Local Message
Intruder Alarm
Fire Alarm
Emergency
Panic Alarm
Tamper Alarm
Environment Alarm
Away Arm
Stay Arm
Disarm
Audible Status
Entry / Exit
Auto Arm
Output On/Off
Walk Test
No Movement
Miscellaneous
0) Exit

Page 164
Appendix F: EN 50131 and EN 50136 Compliance
Compliance Statement

Hereby, RISCO Group declares that the Agility 4 series of central units and accessories are
designed to comply with:

EN50131-1, EN50131-3 Grade 2

EN50130-5 Environmental class II
EN50131-6 Type A
UK: PD 6662:2017
USA: FCC: Part 15B, Part 15C, FCC Part 68

EN50136 Compliance

EN50136-1 EN50136-2 and EN50131-10: PSTN (SP2); GSM 2G/3G (SP4); IP (SP4);
GSM primary and IP secondary (DP3); IP primary and GSM secondary (DP3)
PSTN module can be connected to monitoring station via any EN50136 compliant
receiver, which shall meet all requirements of securing messages.
When IP and/or GSM modules are in use, IP Receiver software is also in use. The IP
Receiver should be connected to automation software, which serves as the EN50136
annunciator. If connection between the IP Receiver and the automation software is lost,
an error message will appear on the IP Receiver queue.
In order to have an indication of ACK received from the monitoring station transceiver,
the parameter Kiss-Off Y/N should be set to Y

Possible logical code calculations

Logical codes are codes punched in the wireless keypad to allow level 2 (users) and
level 3 (installer) access.
All codes - 4 digits structure: xxxx
0-9 can be used for each digit.
There are no disallowed codes - codes from 0001 to 9999 are acceptable.
Invalid codes cannot be created due to the fact that after the code 4th digit has been
punched, "Enter" is automatically applied. Code is rejected when trying to create a non
existing code.

Possible physical key calculations

Physical keys are implemented in the wireless keyfobs.

It is assumed that only a user possesses a keyfobs, therefore a physical key is considered
as access Level 2

Page 165
 Each keyfob has 24 bit identification code comprising 2^24 options.
A keyfob has to be recognized and registered by the Agility 4, therefore, a "write"
process must be performed.
A valid keyfob is one "learned" by the panel and allowing Arm/Disarm
A non valid keyfob is one not "learned" by the panel and not allowing Arm/Disarm.

System Monitoring

The main unit is monitored for AC trouble, battery fault, low battery and more.
The I/O Wireless Expander is monitored for AC trouble, battery fault, low battery and
more.
All other wireless elements are monitored for low voltage battery.

Setting the Agility 4 to comply with EN 50131 requirements

1. Access the Installer programming mode.

2. From the [1] System menu select [5] to access the Settings menu.
3. From the Settings menu select [4] to access the Standard option.
4. Select EN 50131. Once selected, the following changes will occur in the Agility 4
software:

Report Codes Feature EN 50131 Compliance

Timers
Phone Line cut delay Immediate (0 minutes)
Entry Delay 45 seconds (maximum allowed)
AC Delay Immediate (0 minutes)
Jamming Time 0 minutes
RX Supervision 2 hours

System Controls
Quick Arm Set to NO
False Code Trouble Set to Yes
Forced Arming Set to NO
Authorize installer Set to YES
Override Trouble Set to NO
Restore Alarm Set to YES
Mandatory Event Log Set to YES
Restore Trouble Set to YES
Exit Alarm Set to NO

Page 166
Report Codes Feature EN 50131 Compliance
20 Minutes Signal Set to YES
Entry Alarm Set to NO
Attenuation Set to YES

Page 167
Appendix G: SIA CP-01 Compliance
Compliance Statement
Hereby, RISCO Group declares that the Agility 4 series of central units and accessories are
designed to comply with SIA CP 01.
The minimum requirement system for SIA-FAR Installations to comply with CP-01
standards:
A minimum of 1 keypad (Agility KP) must be installed
1 CP-01 Main panel (Agility Main)
All system keypads must be audible (mute disabled).
Setting the Agility 4 to comply with SIA CP 01 requirement
1. Access the Installer programming mode.
2. From the [1] System menu select [5] to access the Settings menu.
3. From the Settings menu select [4] to access the Standard option.
4. Select CP 01, once selected, the following changes will occur in the Agility 4 software:
Report Codes
Feature CP 01 Compliance
Timers
Phone Line cut delay Immediate (0 minutes)
Entry Delay 45 seconds (maximum allowed)
AC Delay Immediate (0 minutes)
Jamming Time 0 minutes
RX Supervision 2 hours
System Controls
Quick Arm Set to NO
False Code Trouble Set to Yes
Forced Arming Set to NO
Authorize installer Set to YES
Override Trouble Set to NO
Restore Alarm Set to YES
Mandatory Event Log Set to YES
Restore Trouble Set to YES
Exit Alarm Set to NO
20 Minutes Signal Set to YES
Entry Alarm Set to NO
Attenuation Set to YES

Page 168
Feature Range Shipping default Quick Key / Remark
Exit Delay time 45 sec - 255 sec 45 seconds [1][1][1][2] / [1][1][2][2]

Progress annunciation Not programmable Enabled

Exit Restore For re-entry during Enabled [1][2][41]

exit delay

Auto Stay arm on un- If there is no exit after Enabled [1][2][42]

vacated premises full arm

Entry Delay(s) 30 sec - 240 sec** 30 seconds [1][1][1][1] / [1][1][2][1]

Abort Window - for May be disabled by Enabled [2][0][4]

non-fire zones zone

Abort window- for 15 sec - 45 sec** 30 seconds [5][6][0][1]

non-fire zones

Abort annunciation Annunciate that no Enabled LCD Display message

alarm was transmitted

Communication 5-255 minutes 005 minutes [5][6][0][2]

Cancel window

Duress feature Not a duplicate of Disabled [4][1] Can define

other user codes dedicated user with
authority level

Cross zoning (XX) sec 1-9 minutes Disabled [2][7]

Swinger shutdown For all non-fire zones, One trip [5][6][8]

shutdown at 1 or 2
trips

Fire alarm verification Depends on sensors Enabled [1][2][10]

Call waiting cancel Depends on user Disabled (Empty [5][6][0][3]

phone line string) String required for
activation

System test (test report Test periodically Disabled [6][8][0][5] / [6][8][0][6]

+ walk test mode + Report to MS enabled
siren) when report code is
entered

AC Power Loss Enabled LCD message display

indication during AC power loss

Page 169
Appendix H: Agility 4 Accessories
868MHz part numbers 433MHz part numbers Description
Keypads
RW132KPPW30B RW132KPPW30I 2-Way LCD keypad
RW332KPP800B RW332KPP400A WL Panda KP+Prox,868
RW332KP0800B RW332KP0400A WL Panda KP,868
RW132KL2P00A RW132KL2P00H 2-Way white internal Slim keypad + Proximity
RP200KT0000A RP200KT0000A RISCO 10 Proximity tags, black, 13.56 MHz
Keyfobs
RW132KF1800A 4 button, black, remote control
RP128T4RC00B RP296T4RC00B 4 button, gray, remote control
RWX132KF800A 2-Way WL remote control
RWT51P80000A RWT51P40000A Wristband panic transmitter
RWT52P86800A RWT52P43300A 2-button panic keyfob
RWT54086800A 4-button zone keyfob
RWT50P86800B Wireless pendant transmitter
RWX332KF800B RWX332KF400A Panda 2Way KeyFob
Wireless Sirens
RWS42086800B RWS42043300B Wireless Indoor round sounder
RWS33200800A RWS33200400A WL 2W Internal Sounder
RWS52A86800B None Wireless oval external sounder, amber

RWS50x86800B RWS50x43300B Wireless triangle external sounder

(x: A=amber, R=red, B=blue)
RWS20A86800B None Wireless ProSound external sounder

RWS401x8000B RWS401B4000B Wireless Lumin8 external sounder

868 (x: A=amber, R=red, B=blue) 433 (blue)
Communication
RW132MD2400A Agility PSTN module
RW132G30000A GSM/3G MSoc + Ant. Plastic box
RW132G20000A GSM/2G Agility Plug-in Module
RW132IP0000A Plug-in TCP/IP module
RP51200W000A Wi-Fi Plug-in + metal box ant.
RP512IP0000A IP Multi-Socket Plug-in Module
RCGSMANT100A Agility GSM antenna, 3m
Safety
RWT6FW86800B RWT6FW43300B Wireless flood detector
RWX34S86800B RWX34S43300B Wireless smoke detector and heat
RWX35S00800C RWX35S00400C WL Smoke & Heat
Perimeter
RWX312PR400C 2-Way wireless WatchOUT PIR
RWT312PR800C RWT312PR400C Wireless WatchOUT PIR
RWT6G086800C RWT6G043300C Wireless Glassbreak detector
RWT6SW86800D Wireless Shock detector
RWT62W86800B RWT62W43300B Wireless Shock + Contact
RWX10680000A RWX10640000A 1 & 2-Way WL Curtain PIR
PIR Cameras

Page 170
868MHz part numbers 433MHz part numbers Description
RWX95CM8000C RWX95CM4000C 2-Way wireless eyeWAVE PIR Cam
RWX95CMP800C RWX95CMP400C 2-Way Wireless eyeWAVE Pet Cam
RWX350DC800A RWX350DC400A WL Beyond DT Cam
PIR Detectors
RWX95086800C RWX95043300B 2-Way Wireless iWAVE PIR
RWX95P86800C RWX95P43300B 2-Way Wireless iWAVE Pet
RWT92086800E RWT92043300E iWISE Wireless PIR detector
RWT92P86800E iWISE WL PIR PET detector
RWX96086800A RWX96043300A 1&2 Way WL Piccolo PIR
RWX96P86800A RWX96P43300A 1&2 Way WL Piccolo Pet
RWX515PR080A RWX515PR040A 2 Way WL BWare PIR
RWX515PT080A 2 Way WL BWare Pet
Shock&Magnetic Contact
Detectors
RWT7808680MA None 1-Way Slim Contact
RWT72M86800E RWT72M43300E Wireless Door/Window Contact
RWT72C43300E Wireless Universal transmitter
RWT72P86800E None Wireless Pulse Count transmitter
RWT72X86800E None Wireless Dual Channel transmitter
RWT72I86800E None Wireless door/window contact
RWX73M86800B 2-Way door/window contacts
RWX73F86800A RWX73F43300A 2-Way multi-function contacts
RWX73F8BL00A 2-Way Multi Contact, Black
RWX73F8BR00A 2-Way Multi Contact, Brown
RWX7808680MA RWX7804330MA 2-way Slim Contact
RWX780868SMA RWX780433SMA 2-way Slim Shock&Contact
RWX780868S0A 2-way Slim Shock Detector
RWX780868M3A 2-way Slim Contact X73
RWX75M86800A 2-Way WP Door/Window Contacts
DT Detectors
RWX350D0800A RWX350D0400A WL Beyond DT
RWX95DT0800B 2 Way WL iWave DT,
RWX95DTP800B 2 Way WL iWave DT Pet
RWX515DT080A 2 Way WL BWare DT
RWX515DTP80A 2 Way WL BWare DT Pet
RWX107DT800A RWX107DT400A WL Outdoor DT Curtain
Input / Output Expander
RW132I04000B Wireless Input/Output Expander

Page 171
Miscellaneous – part numbers Description
RVCM11W0000B VUpoint 1.3MP WiFi Cube Camera
RVCM52W0100B VUpoint 1.3MP WiFi Bullet Camera
RVCM32W0200A VUpoint 1.3MP WiFi Dome Camera
RVCM11P0900A Cube 1.3MP PoE SD Slot
RVCM32P1000A Dome 2MP PoE SD Slot
RVCM52P1100A Bullet 2MP PoE SD Slot
RVCM52P1300A Bullet Varifocal 2MP PoE SD Slot
RVCM72P1200B Eyeball 2MP PoE SD Card
RVCM61H0300A IP Cam: PT, 1.3MP, WiFi, SD Slot
RVCM52E0400A IP Cam: Bullet 4MP 2.7-12mm WDR
RVCM32E0500A IP Cam: Dome, 4MP, 2.7-12mm, WDR
RVCM72E0700A IP Cam: Eyeball 4MP WDR H.265
RVCM82E0800A IP Cam: IR PTZ, 2MP, Starlight, H.265
RW132CB0000A RS232 PC-to-panel cable
RW132EUSB00A Agility-to-USB adaptor
RAX73MS0000A X73 Magnet spacers x 10, white
RAX73MSB000A X73 Magnet spacers x 10, brown
RAX73MSBL00A X73 Magnet spacers x 10, black
RAX73XS0000A X73 Transmitter spacers x 10, white
RAX73XSB000A X73 Transmitter spacers x 10, brown
RAX73XSBL00A X73 Transmitter spacers x 10, black
RA78UNI0000A X78 External/Shutter TB Bracket
RA350SSLR00A WL Beyond 180° Solar Swivel Kit

Page 172
RED Compliance Statement
Hereby, RISCO Group declares that this equipment is in compliance with the essential requirements
and other relevant provisions of Directive 2014/53/EU . For the CE Declaration of Conformity please
refer to our website: www.riscogroup.com.

FCC Note
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
a) Reorient or relocate the receiving antenna.
b) Increase the separation between the equipment and receiver.
c) Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
d) Consult the dealer or an experienced radio/TV technician.

FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Changes or modifications to this equipment which are not expressly approved by the party responsible
for compliance (RISCO Group’s) could void the user’s authority to operate the equipment.
FCC ID: JE4STAMP433, JE4STAMP433-916 Valid for P/N RW132x4t0zza

Page 173
Standard Limited Product Warranty
RISCO Ltd., its subsidiaries and affiliates (“RISCO") guarantee RISCO’s hardware products to be free
from defects in materials and workmanship when used and stored under normal conditions and in
accordance with the instructions for use supplied by RISCO, for a period of (i) 24 months from the
date of connection to the RISCO Cloud (for cloud connected products) or (ii) 24 months from
production (for other products which are non-cloud connected), as the case may be (each, the
“Product Warranty Period” respectively).
Contact with customers only. This Product Warranty is solely for the benefit of the customer who
purchased the product directly from RISCO, or from any authorized distributor of RISCO. Nothing in
this Warranty obligates RISCO to accept product returns directly from end users that purchased the
products for their own use from RISCO’s customer or from any installer of RISCO, or otherwise
provide warranty or other services to any such end user. RISCO customer shall handle all interactions
with its end users in connection with the Warranty, inter alia regarding the Warranty. RISCO’s
customer shall make no warranties, representations, guarantees or statements to its customers or other
third parties that suggest that RISCO has any warranty or service obligation to, or any contractual
privy with, any recipient of a product.
Return Material Authorization. In the event that a material defect in a product shall be discovered
and reported during the Product Warranty Period, RISCO shall, at its option, and at customer's
expense, either: (i) accept return of the defective Product and repair or have repaired the defective
Product, or (ii) accept return of the defective Product and provide a replacement product to the
customer. The customer must obtain a Return Material Authorization (“RMA”) number from RISCO
prior to returning any Product to RISCO. The returned product must be accompanied with a detailed
description of the defect discovered (“Defect Description”) and must otherwise follow RISCO’s then-
current RMA procedure in connection with any such return. If RISCO determines in its reasonable
discretion that any Product returned by customer conforms to the applicable warranty (“Non-
Defective Products”), RISCO will notify the customer of such determination and will return the
applicable Product to customer at customer’s expense. In addition, RISCO may propose and assess
customer a charge for testing and examination of Non-Defective Products.
Entire Liability. The repair or replacement of products in accordance with this warranty shall be
RISCO’s entire liability and customer’s sole and exclusive remedy in case a material defect in a
product shall be discovered and reported as required herein. RISCO’s obligation and the Warranty are
contingent upon the full payment by customer for such Product and upon a proven weekly testing
and examination of the product functionality.
Limitations. The Product Warranty is the only warranty made by RISCO with respect to the Products.
The warranty is not transferable to any third party. To the maximum extent permitted by applicable
law, the Product Warranty does not apply and will be void if: (i) the conditions set forth above are not
met (including, but not limited to, full payment by customer for the product and a proven weekly
testing and examination of the product functionality); (ii) if the Products or any part or component
thereof: (a) have been subjected to improper operation or installation; (b) have been subject to neglect,
abuse, willful damage, abnormal working conditions, failure to follow RISCO’s instructions (whether
oral or in writing); (c) have been misused, altered, modified or repaired without RISCO’s written
approval or combined with, or installed on products, or equipment of the customer or of any third
party; (d) have been damaged by any factor beyond RISCO’s reasonable control such as, but not
limited to, power failure, electric power surges, or unsuitable third party components and the
interaction of software therewith or (e) any delay or other failure in performance of the product

Page 174
attributable to any means of communications, provided by any third party service provider
(including, but not limited to) GSM interruptions, lack of or internet outage and/or telephony failure.
BATTERIES ARE EXPLICITLY EXCLUDED FROM THE WARRANTY AND RISCO SHALL NOT BE
HELD RESPONSIBLE OR LIABLE IN RELATION THERETO, AND THE ONLY WARRANTY
APPLICABLE THERETO, IF ANY, IS THE BATTERY MANUFACTURER'S WARRANTY.
RISCO makes no other warranty, expressed or implied, and makes no warranty of merchantability or
of fitness for any particular purpose. For the sake of good order and avoidance of any doubt:
DISCLAIMER. EXCEPT FOR THE WARRANTIES SET FORTH HEREIN, RISCO AND ITS
LICENSORS HEREBY DISCLAIM ALL EXPRESS, IMPLIED OR STATUTORY, REPRESENTATIONS,
WARRANTIES, GUARANTEES, AND CONDITIONS WITH REGARD TO THE PRODUCTS,
INCLUDING BUT NOT LIMITED TO ANY REPRESENTATIONS, WARRANTIES, GUARANTEES,
AND CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE
AND LOSS OF DATA. WITHOUT LIMITING THE GENERALITY OF THE FOREGOING, RISCO
AND ITS LICENSORS DO NOT REPRESENT OR WARRANT THAT: (I) THE OPERATION OR USE
OF THE PRODUCT WILL BE TIMELY, SECURE, UNINTERRUPTED OR ERROR-FREE; (ii) THAT
ANY FILES, CONTENT OR INFORMATION OF ANY KIND THAT MAY BE ACCESSED THROUGH
THE PRODUCT BY CUSTOMER OR END USER SHALL REMAIN SECURED OR NON DAMAGED.
CUSTOMER ACKNOWLEDGES THAT NEITHER RISCO NOR ITS LICENSORS CONTROL THE
TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET,
GSM OR OTHER MEANS OF COMMUNICATIONS AND THAT RISCO’S PRODUCTS, MAY BE
SUBJECT TO LIMITATIONS, DELAYS, AND OTHER PROBLEMS INHERENT IN THE USE OF
SUCH MEANS OF COMMUNICATIONS. RISCO IS NOT RESPONSIBLE FOR ANY DELAYS,
DELIVERY FAILURES, OR OTHER DAMAGE RESULTING FROM SUCH PROBLEMS.
RISCO WARRANTS THAT ITS PRODUCTS DO NOT, TO THE BEST OF ITS KNOWLEDGE,
INFRINGE UPON ANY PATENT, COPYRIGHT, TRADEMARK, TRADE SECRET OR OTHER
INTELLECTUAL PROPERTY RIGHT
IN ANY EVENT RISCO SHALL NOT BE LIABLE FOR ANY AMOUNTS REPRESENTING LOST
REVENUES OR PROFITS, PUNITIVE DAMAGES, OR FOR ANY OTHER INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF THEY WERE FORESEEABLE OR
RISCO HAS BEEN INFORMED OF THEIR POTENTIAL.
RISCO does not install or integrate the product in the end user security system and is therefore not
responsible for and cannot guarantee the performance of the end user security system which uses the
product.
RISCO does not guarantee that the product will prevent any personal injury or property loss by
burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate warning or
protection.
Customer understands that a correctly installed and maintained alarm may only reduce the risk of
burglary, robbery or fire without warning, but is not an assurance or a guarantee that such an event
will not occur or that there will be no personal injury or property loss as a result thereof. Consequently
RISCO shall have no liability for any personal injury, property damage or loss based on a claim that
the product fails to give warning.
No employee or representative of RISCO is authorized to change this warranty in any way or grant any
other warranty.

Page 175
Contacting RISCO Group
RISCO Group is committed to customer service and product support. You can contact us
through our website www.riscogroup.com or via the following:

Belgium (Benelux) Israel United Kingdom

Tel: +32-2522-7622 Tel: +972-3-963-7777 Tel: +44-(0)-161-655-5500
[email protected] [email protected] [email protected]
China (Shanghai) Italy USA
Tel: +86-21-52-39-0066 Tel: +39-02-66590054 Tel: +1-631-719-4400
[email protected] [email protected] [email protected]
France Spain
Tel: +33-164-73-28-50 Tel: +34-91-490-2133
[email protected] [email protected]

This RISCO product was purchased at:

FCC

No part of this document may be reproduced in any form without prior written permission
from the publisher.

© RISCO Group 08/2020. All rights reserved. 5IN2861 B

Page 176