th

Notice: B.E 8 Semester – 2024

Guidelines for Preparation of Project Report

(As per information available on V.T.U website vide VTU Circular No. VTU/Exam/2001-2002/2469 dt 05/06/2002)

1. Project reports should be typed neatly only on one side of the paper with 1.5 line spacing
on a A4 size Bond Paper (210 x 297 mm). Report must be hard-bound with plastic cover.
2. Margins: Left:- 1.25″ Right:- 1″ Top:- 0.75″ Bottom:- 0.75″
3. Total number of copies of report to be prepared:
• 1 college copy.
• 1 copy for the guide.
• 1 copy to each candidate
4. Before taking the final printout, approval of the concerned guide(s) is mandatory and
suggested corrections, if any, must be incorporated.
5. Every copy of the report must contain:
• Outer title page/cover: Cream color with plastic cover.
• Inner title page: White bond sheet
• Certification from college (Refer to the given format)
• Declaration (Refer to the given format)
• Abstract (synopsis) not exceeding 100 words, indicating salient features of the work.
6. Organization of the report:
• Inner title page.
• Certificate.
• Declaration.
• Abstract / synopsis
Numbered in Roman
• Acknowledgement.
• Table of contents.
• List of tables.
• List of figures.
• Chapters (containing Introduction & Main body of report)
• References.
7. Chapters (to be numbered in Arabic as 1, 2 etc.): Introduction usually specifies scope of
work, its importance, relation to previous work and the present developments. Main body
of the report must be divided appropriately into chapters, sections & subsections.
8. Chapters, sections and subsections may be numbered in the decimal form. E.g.:
Chapter 2, Sections as 2.1, 2.2 etc., and sub sections as 2.2.1, 2.2.2 etc.
9. Font size (refer to the example in next page)
10. Figures and Tables must be numbered chapter-wise. E.g., 2.1 Block Diagram of … Table
3.1 Primitive Flow… table. All figures and tables are to be placed either at the top or
bottom of the page and should appear in the same page or the next page in which they are
referred first.
 Header
Right Aligned
Font Size: 12 pt
Title of the project
Left Aligned
Title of Chapter
Chapter 1 Font Size: 16 pt
Center Aligned
Font Size: 18 pt

Introduction
Left Aligned
1.1 Section Font Size: 16 pt

Left Aligned
1.1.1 Sub Section Font Size: 14 pt

Text of the report

Justified
Font Size: 12 pt

Centered
Font Size: 10 pt Figure/Table
(Centered)

Fig/Table 1.1 Details of Figure / Table

Footer
Font Size: 10 pt

Dept. of CSE, ACSCE 2023-24 1

11. Last chapter should contain Summary of the work carried out, their utility along with
scope for further work.
12. Reference: References should be number serially in the order of occurrence in the text and
their numbers should be indicated in square brackets. E.g.: [1].
Section of Reference should list them in serial order in the following format:
For text books:
A.V. Openheim and R.W. Schafer, Digital Signal Processing, Englewood, NJ, Prentice Hall,
rd
3 Edition, 1975.
For Papers:
David, Insulation Design to Combat Pollution, Proc. Of IEEE, PAS, Vol 71, Aug 1981, pp
1901-1907
13. Equations must be numbered chapter-wise in decimal form and equation numbers must be
right justified.
E.g: F = m.a (1.1)
 VISVESVARAYA TECHNOLOGICAL UNIVERSITY
Jnana Sangama, BELGAUM

Project Report on
<Title of the Project>

In partial fulfillment of the requirements for the award of the Degree of

BACHELOR OF ENGINEERING
IN
COMPUTER SCIENCE AND ENGINEERING
By

Student Name1 USN1

Student Name2 USN2
Student Name3 USN3
Student Name4 USN4

Under the guidance of

<Name of the Guide>
<Designation>, Dept. of CSE
ACS COLLEGE OF ENGINEERING, Bangalore

DEPARTMENT OF COMPUTER SCIENCE AND ENGINEERING

ACS COLLEGE OF ENGINEERING

KAMBIPURA, MYSORE ROAD, BANGLORE-74
2023-2024
 ACS COLLEGE OF ENGINEERING
KAMBIPURA, MYSORE ROAD, BANGLORE-74

Department of Computer Science and Engineering

Certificate
Certified that the Project Work entitled “Title of the Project” is a bonafide work
carried out by Mr. /Ms Name1 (USN1), Mr. /Ms Name1 (USN1), Mr. /Ms Name2 (USN2),
Mr. /Ms Name3 (USN3), and Mr. /Ms Name4 (USN4) in partial fulfillment for the award of
Bachelor of Engineering in Computer science & Engineering of the Visvesvaraya
Technological University, Belgaum during the year 2023-2024. It is certified that all the
corrections/suggestions indicated for internal assessment have been incorporated in the report
deposited in the departmental library. The Project Report has been approved as it satisfies the
academic requirements in respect of Project Work prescribed for the said degree.

Signature of Guide Signature of HOD Signature of Principal

[Guide’s Name] [Dr. T Sentil Kumar] [Dr. Anandthirtha B Gudi]

S.No Name of The Examiners Signature With Date

1.
2.
 DECLARATION

We, Mr/Ms Name1 (USN1), Name2 (USN2), Name3 (USN3) and Name4(USN4),
hereby declare that the project work entitled “Title of the Project” has been independently
carried out by us under the guidance of Dr./Prof./Mr. Name of the Guide, Designation,
Department of Computer Science & Engineering, ACS College of Engineering,
Bangalore, in partial fulfillment of the requirements of the degree of Bachelor of Engineering
in Computer Science & Engineering of Visvesvaraya Technological University, Belgaum.

We further declare that we have not submitted this report either in part of in full to
any other university for the reward of any degree.

Name of Student 1 Sign

Name of Student 2 Sign
Name of Student 3 Sign
Name of Student 4 Sign

Place: Bangalore
Date: