Find the readings of Ammeter and Voltmeter

Find the voltages Va, Vb and Vc

Find the voltages VA, VB and VAB

The voltage across R4 is 5V, find V. If 2R5=R2=2R1

VAB =4v, find the voltage across the 1mA current source(VCD)

Find Vo for the following values of R1 & R2.

(i) R1=1k & R2 = 1k, (ii) R1=50Ω & R2=50Ω.

Find V1, V2, V3, V4

a) V1=2V, V2= 1V, V3=1V, V4= 1V

b) V1=2.5V, V2=1.25V, V3= 1.25V, V4= 2.5V
c) V1=2.5V,V2=2.5V,V3=2.5V, V4=2.5V
d) None of the above

Find Io & Vo for the following values

(i) R=1k
(ii)R=10k

Find the power dissipations in the lamp.

Find I.

Find RAB

VAB?

a) 0V b) infinite volt c) 10V d) none of these

Find the values of Vo for the following values of R

(i) R=1k (ii) R=100k

Find I

a) 20mA b) 10mA c)-20mA d) -10mA

Find the maximum value of voltage that can be given so that both bulbs are operated safely

1. For a transmission line open circuit and short circuit impedances are 20 and 5 . What is
the characteristic Impedance?
2. For high frequencies a capacltor acts like a ____________
3. In the circuit of figure, the switch is closed at t=0. At t= 0+ the current through C is

4. Assuming battery rating is V = 10V, 10AH. Estimate V effective and Rating effective
(a) Four battery in Parallel: V = Volt; Rating= AH;
(b) Four battery in Series: V= Volt; Rating= AH;
5. If the current through 3 Ohm resistor is 0.8A, then potential drop across 4 Ohm resistor is,

6. What is the reading by voltmeter and ammeter for switch open condition and switch close
condition,
7. What is the reading by volt meter and ammeter,

8. Find the measured resistance across the points R1 and R2

9. What is the value of l1 & 12 ?

10. What meant by time constant of RC network ? What is the seting time for an RC
network with respect to time Constant ?
11. In the circuit of figure, find out the voltage across capacitor when switch is closed & at
t=ꝏ,

12. Find 11, 12 and 13.

 13. Any Transmission lines consists of elements
A. Resistance and Inductance
B. Resistance and Capacitance
C. Inductance and Capacitance
D. Resistance, Inductance and Capacitance

14. Find the resistance across A and B in the below network

a. 26.67K
b. 5K
c. 15K
d. 50K

15. What component in a circuit sill make current & Voltage waveform of a same signal
out of syne?
a. R and C
b. L and C
c. Both A and B
d. Only R
16. In a transformer, if the voltage ratio is 1:1 from primary to secondary side. What will be
the current ratio from Primary to secondary
a. 00.01.00
b. 05.05.00
c. 01.00.00
d. 10.01.00
17. A resistive load consumes 100W power from a 200V DC power supply. How much
power will be consumed by the same load, if it will be connected to a 100V DC power
supply?
a. Resistor will damage
 b. 50 watt
c. 25 watt
d. 100 watt
18. What will be effective resistance across A and B?

a. 15 b. 10 c. 5 d. 20
19. In the given figure assume R1=R2=R3, What will happen to the current through R1
and R2 if resistor R3 is removed?

a. Increase, Increase
b. Increase, Decrease
c. Same, Same
d. Decrease, Decrease
20. Which kind of filter does the RC circuit shown below represent?

a. Low Pass b. High Pass c. Band Pass d. Band Reject

21. Find the current across load resistors Rs, if R1=800Ω, R2=200Ω, R3=2400Ω, and
R4=600Ω
 a. 1A b. 0A c. A2 d. Data insuffcient
22. For the RC circuit shown below, what is the output voltage?

23. A resistor allows a current of 0.6A to flow when connected to a 9.6V DC supply. What
current will flow if the same resistor is connected to a 12.8V supply?
a. 0.2A b. 0.8A c. 22.4A d. 6.4A
S.No Question
12.07.2024

1. What will be the effective resistance across AB

2. Given two resistors R1=10Ω and R2=20Ω connected in series, what is the total resistance of this
configuration?
3. Given two resistors, R1=40Ω and R2=100Ω, what is the equivalent resistance of the parallel combination
of these resistors, that is R1∣∣R2?
4. Given three resistors R1=10Ω, R2=20Ω and R3=1000Ω connected in parallel, what is the total resistance
of this configuration? Enter the value in the box below without the unit. Round the result to two decimal
places if necessary.
5. Given three resistors R1=10Ω, R2=20Ω and R3=1000Ω connected in parallel, what is the total resistance
of this configuration? Enter the value in the box below without the unit. Round the result to two decimal
places if necessary.
6. Find the resistance across A and B in the below network

e. 26.67K
f. 5K
g. 15K
h. 50K
7. A resistive load consumes 100W power from a 200V DC power supply. How much power will
be consumed by the same load, if it will be connected to a 100V DC power supply?
e. Resistor will damage
f. 50 watt
g. 25 watt
h. 100 watt
8. Which of the options are true for the circuit below?

D and E are in parallel.

B and C are in series.

J and K are in parallel.

H and L are in parallel.

9. Find the equivalent resistance between the points a and b for the circuit below if R1=500Ω, R2=300Ω,
and R3=500Ω.

10. Find the equivalent resistance, Req, between the nodes a and b if R1=R8=400Ω,R2=R3=500Ω,
R4=R6=100Ω, and R5=500Ω.

11. ab for the circuit below. Use the short notation || to mean "in parallel with"; for example, "R1 || R2" means
R1 in parallel with R2. Which of the following expressions represents Req.

R1 + ((R5+R6)||R4+R3)||R2 + R8

(R1+R8+R2)||(R3+R4)||(R5+R6)

(R5+R6)||R4 +(R3+R2) + R1 + R8

R1+R8+R2||(R3+R4)||(R5+R6)

12. Find R

13. Find Req

a. 6 b. 8 c. 4 d. 10
14. Four equal resistance of 40Ω each are connected in parallel across a 120 V dc supply. What is the current
through each of them?
a) 12A b) 6A c) 3A d) 9A
Answer
15. Suppose you have a resistor with the following sequence of color bands: Yellow-Green-Red-Silver What
is the resistance of this resistor?
Ans–
16. Calculate the maximum safe current that can pass through a 1.8 KΩ resistor rated at 0.5W.
1.6A b) 0.16A c) 0.016A d) 0.0016A
17. Three resistance of 1Ω, 2Ω,4Ω are connected in parallel in a circuit. If a 1 Ω resistor draws a current of
1A find the current through other two resistors. List 1Ω, 2Ω,4Ω drawing current respectively
a) 1, 1, 1
b) 1, 2, 2
c) 1, 0.5, 0.25
d) 1, 0.25, 0.5
18. The nodal method of circuit analysis in based on
a) KVL and ohm’s law
b) KCL and ohm’s law
c) KCL and KVL
d) KCL, KVL and ohm’s law
19. What is the equivalent resistance for the circuit shown below

a) Equal to 6
b) Less than 6
c) Greater than 6
d) None of the above
20. Find the resistance across A and B in the below network

a) 26.67K b. 5K c. 15K d.50K

21. In the given figure assume R1=R2=R3. What will happen to the current through R1 and R2 if resistor R3
is removed?

a) Increase, increase
b) Increase, decrease
c) Same, same
d) Decrease, Decrease
d) Circuit incomplete
22. Find the voltage across 9ohm resistor.
 a) 9V
b)6V
c)3V
23. Find V

Ans= -6V
24. Find the values of Vo for the following values of R
(i) R=1k (ii) R=100k

a) 0.1V, 10V
b) 10V, 0.1V
c) 0.1V, 1.0V
d) 1V, 10V
25. Find RAB

a) 4kΩ b. 6kΩ c. 8kΩ d. 2kΩ

26. Find the equivalent resistance between the terminal a and b. Enter the value in the box below without
units.

27. Find the equivalent resistance of the following circuit between terminals a and b. Enter the value in the
box below without units.
28. Find Req for the resistive network shown below. Each resistor is 100Ω.

a. 73.2 b. 7.32 c. 17.32 d. 1.732

29. Find Req for the resistive network shown below

a.1 b. 2 c. 3 d. 4
30. What will be the effective resistance across A and B?

a. 5 b. 10 c. 15 d. 20
31. Find an equivalent resistance between A & B

a)3.33Ω b)2.22Ω c) 1.11Ω d) 1000Ω

32. Find the equivalent resistance between A & B

a) 20.33Ω b) 2.033Ω c) 203.3Ω d) 0.2033Ω

33. What is the equivalent resistance, if ‘n’ equal ‘R’ resistance are connected in parallel.
a) R/n b) nR c) R+n d) R+n/R-n
34. What will be the resistance & 10 resistors of 10Ω each in connected in series
a) 10Ω b) 100Ω c) 300Ω d) 500Ω
35. Equivalent resistance _______ .
 a)=6 b. <6 c. >6 d. None
36. What is equivalent capacitance between terminal A & B

a) 2.85µF b)2.85pF c)28.5 µF d)28.5 F

37. Calculate the equivalent capacitance Cab for the following schematic. Ans 3

38. What is the total equivalent inductance looking into terminal a and b? Assume all inductors have the
same inductance of 55 Henry. Please put the numerical answer in Henry in the box provided below. Do
not put in the units. If necessary round your answer to two decimal places. Ans 6

39. Calculate the equivalent inductance, Lab, for the following schematic. All inductors have an inductance of
0.2mH.

Enter your numerical answer below in milli-Henry (mH). Round to two decimal places if necessary. Ans
0.55
40. For high frequencies a capacitor acts like a ____________
Answer -
41. Calculate the equivalent capacitance across the terminal A and B.
 6.66uF 15uF 30uF 40uF
42. For a transmission line open circuit and short circuit impedances are 20 and 5. What is the
characteristic Impedance?
a) 5Ω b) 10Ω c) 15Ω d) 20Ω
Answer
The characteristic impedance (Z0) of a transmission line can be determined using the open-circuit
impedance (ZOC) and the short-circuit impedance (ZSC). The formula for calculating the characteristic
impedance is:

43. Find the power dissipations in the lamp.

a) 25W b) 50W c)100W d)200W

44. Find the maximum value of voltage that can be given so that both bulbs are operated safely

45. A source whose no-load voltage is 220 V delivers 20 watts to a load when the current is 0.4 A. Calculate
the internal resistance of the source.

46. Consider the experiment depicted in the figure. Suppose R1=1000Ω and R2=4000Ω. Determine the
voltage read by the Digital Multimeter (DMM) in volts. Enter the value in the box below without the units.

47. When 5 DC sources with rating of 3V, 1A each are connected in series. What will be the effective Voltage
that can be delivered?
5V, 10V, 15V, 20V
48. If 5 bulbs in a room with a rating of 10V, 1A has to be connected to a supply, what should be the
minimum rating of the supply when it is connected in series?
10 V 20V 25V 50V

49. If 5 bulbs in a room with a rating of 10V, 1A has to be connected to a supply, what should be the
minimum rating of the supply when it is connected in parallel?
 10 V 20V 25V 50V

50. 100 V, 60 W lamp is connected in series with a 100 V, 100 W lamp across 200 V supply . What will be the
current drawn by the lamp? Will such a combination work?
a) 0.75A, circuit will not work.
b) 7.5A, circuit will work.
c) 0.75A, circuit will work.
d) 7.5A, circuit will not work.
13.07.2024

51. What is the potential difference between points x + y in the network shown

a) 3.7 V b) -3.7 V c) 37 V d) -37 V

52. Refer the circuit if V2=48 V what is the potential drop at 50Ω.

a) 18 V b) 8 V c) 28 V d) 56 V
53. The voltage across terminal a, b is

a) 0.5 V b) 3V c) 3.5 V d) 4V
54. Find VAB?

a) 0V b) infinite volt c) 10V d) none of these

55. What the phasor diagram infers

a) Voltage leads the current by 90⁰

b) Voltage lags the current by 90⁰
c) Current leads the voltage by 90⁰
d) b&c
56. Find the voltages Va, Vb and Vc

a) 10V, 6V, 3V
b) 15V, 11V, 8V
c) 15V, 6V, 3V
d) 10V, 8V, 6V
57. Find the voltages VA, VB and VAB

a) 5V, 3V, 2V
b) 10V, 6V, 2V
c) 8V, 6V, 4V
d) 5V, 6V, 2V
58. Find the voltage across R4 in 5V, find V. If 2R5=R2=2R1

a) 10V
b) 5V
c) 2.5V
d) 7.5V
59. VAB =4V, find the voltage across the 1mA current source(VCD)

60. Find Vo for the following values of R1 & R2. (i) R1=1k & R2 = 1k, (ii) R1=50Ω & R2=50Ω.
 a) 5V, 5V
b) 10V, 10V
c) 5V, 10V
d) 10V,5V
61. Find V1, V2, V3, V4

e) V1=2V, V2= 1V, V3=1V, V4= 1V

f) V1=2.5V, V2=1.25V, V3= 1.25V, V4= 2.5V
g) V1=2.5V, V2=2.5V, V3=2.5V, V4=2.5V
h) None of the above
62. In the circuit below, Vs=30V, R1=100Ω, and V2=10V. Find the resistance R2. Ans 50

63. Find Io & Vo for the following values

(iii) R=1k
(iv) R=10k

a) 25mA, 25V, 2.5mA, 25V

b) 2.5mA, 2.5V, 25mA, 25V
c) 25mA, 25V, 2.5mA, 2.5V
d) 25mA, 2.5V, 25mA, 25V
64. What is the reading by volt meter and ammeter,
65. If the current through 3 Ohm resistor is 0.8A, then
potential drop across 4 Ohm resistor is,

Ans

66. Calculate V0

67. Assuming battery rating is V = 10V, 10AH. Estimate V effective and Rating effective
(a) Four battery in Parallel: V = Volt; Rating= AH;
(b) Four battery in Series: V= Volt; Rating= AH;

68. Find I.

69. Find I

a) 20mA b) 10mA c)-20mA d) -10mA

70. What is the value of I1 & I2 ?

71. A resistor allows a current of 0.6A to flow when connected to a 9.6V DC supply. What current
will flow if the same resistor is connected to a 12.8V supply?
a. 0.2A b. 0.8A c. 22.4A d. 6.4A
72. Calculate total power of the circuit

A) 200 W
B) 282.88 W
C) 400 W
D) 127.32 W
73. If R = 4 ohms and if the current through the X is 0A, what is the value of current through the resistor R?

a) 1A
b) 0.5 A
c) 0.75 A
d) 0.25A
74. For the circuit below, solve for V3 if R1=50Ω, R2=200Ω, R3=300Ω, and Vs=15V. Ans 9

75. For the circuit below, Vs=15V, and V2=5V. Determine the value of the voltage Vo. Enter the value in the
box below without units

76. For the circuit below, R1=200Ω, R2=400Ω, R3=500Ω, Vs=10v, and Is=0.5A. Use MESH ANALYSIS to
solve for I1 in amps. Enter the value in the box below without the units.

77. Select the network from the list below that is equivalent to the following.
78.

Select all the circuits which are electrically equivalent to the one above. Leave all which are not
electrically equivalent deselected.
79. Obtain the source current I and the total power delivered by the current source to the circuit in the
figure.

2A 4A 6A 8A
80. In the following circuit, if R=100Ω and Vs=10V, 1A. What is the voltage at Vo?

5V 10V 15V 20V

81. What is the current through R?

0A 0.1A 0.01A 1A

82. A coil of inductance 150mH and zero resistance is connected across a 100V, 50Hz supply. Calculate the
inductive reactance of the coil.
15πΩ 150Ω 1500Ω 1.5πΩ

83. Find the value of resistance R shown below

10Ω 20 Ω 30Ω 40Ω

84. Find the value of resistance R shown below

20 30 40 50

85. In figure shown, Find E.

86. Find the single voltage source value _____________.

87. If the 12Ω resistor draws a current of 1A as shown in the figure, the value of resistance R is ________.

Ans 5Ω
88. Find current I

a. 0 b. 1 c. 10 d. None
89. Find the current across load resistors Rs, if R1=800, R2=200, R3=2400, and R4-600

90. Convert voltage source to current source and find the value of current?

91. Four equal resistance of 40Ω each are connected in parallel across a 120 V dc supply. What is the current
through each of them?
a) 12A b) 6A c) 3A d) 9A
92. Three resistance of 1Ω, 2Ω,4Ω are connected in parallel in a circuit. If a 1 Ω resistor draws a current of 1
A find the current through other two resistors. List 1Ω, 2Ω,4Ω drawing current respectively
a) 1, 1, 1
b) 1, 2, 2
c) 1, 0.5, 0.25
d) 1, 0.25, 0.5
93. In which figure the relationship between V & I is in accordance with ohms law.
 1
1

V
V
a) b)

1 1

V V
c) d)
94. Consider the following figure

The current Is in Amps in the voltage source, and Voltage Vs in volts across the current source
respectively are
a) 13,-20 b) 8, -10 c) -8, 20 d) -13, 20

95. In the circuit shown , the value and RL such that the power transferred to RL in minimum is

a) 5Ω b) 10Ω c) 15Ω d) 20Ω

96. In the circuit power supplied by the voltage source is
 a) 0W b) 5W c) 10 W d) 100 W
97. The number of independent loops for a network with ’n’ nodes and ‘b’ branches in
a) n-1 b) b-n c) b-n+1 d)independent of the number of nodes
98.

2V 10V 12V 20V

99. In the circuit given below, the current in the 4-ohm resistor is __________

a) 3.5 A
b) 2.5 A
c) 1.5 A
d) 0.5 A
100. Find the equivalent resistance between node 1 and node 3 in the star connected circuit
shown below.

a) 30
b) 31
c) 32
d) 33