Scribd
Upload
6 views

ENCODER and Decoder

Uploaded by

firam4455
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
6 views

ENCODER and Decoder

Uploaded by

firam4455
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

ENCODER AND DECODER

Prerequisite – Encoder, Decoders Binary code of N digits can be used to store


2N distinct elements of coded information. This is what encoders and decoders
are used for. Encoders convert 2N lines of input into a code of N bits
and Decoders decode the N bits into 2 N lines. 1. Encoders – An encoder is a
combinational circuit that converts binary information in the form of a 2 N input
lines into N output lines, which represent N bit code for the input. For simple
encoders, it is assumed that only one input line is active at a time. As an
example, let’s consider Octal to Binary encoder. As shown in the following
figure, an octal-to-binary encoder takes 8 input lines and generates 3 output

lines. Truth Table –


D7 D6 D5 D4 D3 D2 D1 D0 X Y Z

0 0 0 0 0 0 0 1 0 0 0

0 0 0 0 0 0 1 0 0 0 1

0 0 0 0 0 1 0 0 0 1 0

0 0 0 0 1 0 0 0 0 1 1

0 0 0 1 0 0 0 0 1 0 0

0 0 1 0 0 0 0 0 1 0 1

0 1 0 0 0 0 0 0 1 1 0

1 0 0 0 0 0 0 0 1 1 1
As seen from the truth table, the output is 000 when D0 is active; 001 when D1
is active; 010 when D2 is active and so on. Implementation – From the truth
table, the output line Z is active when the input octal digit is 1, 3, 5 or 7.
Similarly, Y is 1 when input octal digit is 2, 3, 6 or 7 and X is 1 for input octal
digits 4, 5, 6 or 7. Hence, the Boolean functions would be:
X = D4 + D5 + D6 + D7
Y = D2 +D3 + D6 + D7
Z = D1 + D3 + D5 + D7
Hence, the encoder can be realised with OR gates as follows:

:
2. Decoders – A decoder does the opposite job of an encoder. It is a
combinational circuit that converts n lines of input into 2 n lines of output. Let’s
take an example of 3-to-8 line decoder. Truth Table –

X Y Z D0 D1 D2 D3 D4 D5 D6 D7

0 0 0 1 0 0 0 0 0 0 0

0 0 1 0 1 0 0 0 0 0 0

0 1 0 0 0 1 0 0 0 0 0

0 1 1 0 0 0 1 0 0 0 0

1 0 0 0 0 0 0 1 0 0 0

1 0 1 0 0 0 0 0 1 0 0

1 1 0 0 0 0 0 0 0 1 0

1 1 1 0 0 0 0 0 0 0 1

Implementation – D0 is high when X = 0, Y = 0 and Z = 0. Hence,


D0 = X’ Y’ Z’
Similarly,
D1 = X’ Y’ Z
D2 = X’ Y Z’
D3 = X’ Y Z
D4 = X Y’ Z’
D5 = X Y’ Z
D6 = X Y Z’
D7= xyz

You might also like