1.

OPERATE FUEL ,LUBRICATING, FUEL AND OTHER PUMP

2. The following is a crankshaft inspection procedure, except
a. Turn the crankshaft to the bottom position
b. Spray with air
c. Position the deflection gauge between the crank arms
d. Set the deflection gauge to the top, port side, starboard side, and bottom port positions
e. Saya Tidak Tahu
3. What causes the white smoke on the main motor?
a. Fuel injection pressure is too low
b. Lubricating oil that is no longer suitable for use
c. Incorrect fuel ratio
d. No compression in combustion chamber
e. Saya Tidak Tahu
4. Mention the responsibilities of 3rd Engineer?
a. Pumps, Purifiers and Lift boat engines
b. Generator, Boiler, Emg generator
c. Fwg, Winchlas, Main engine
d. Main engine, Fuel and whole engine
e. Saya Tidak Tahu
5. To what degree will the injector atomize the fuel?
a. 19 degrees after TDC
b. 15 degrees after TDC
c. 20 degrees before TDC
d. 17 degrees before TDC
e. Saya Tidak Tahu
6. How many degrees of hot steam does purifier need to work?
a. 40 – 50 degree
b. 65 – 70 degree
c. 45 – 50 degree
d. 50 – 60 degree
e. Saya Tidak Tahu
7. The high pressure pump in the engine to pump fiel into injection is called
a. Carculating Pump
b. Bosch Pump
c. Feed Pump
d. FO Pump
e. Saya Tidak Tahu
8. What needs to be cleaned if the suction pump is very vacuum?
a. Clean the pipe
b. Clean the manmeter
c. Clean the impeller
d. Clean the filter
e. Saya Tidak Tahu
9. What is meant by “SURGING”?
a. The air speed on the wind bottle is low
b. The air speed in the distributor is lo so it can’t start the engine
c. Water velocity at low boiler filling
d. The air velocity in the blower decreases so the pressure reverses
 e. Saya Tidak Tahu
10. The liquid chemical for removing rust is called
a. SAF Acid
b. Hydrogen
c. Rust remover
d. Sulfunic acid
e. Saya Tidak Tahu
11. What causes high exhaust valve, burnt exhaust gas manifold, high temperature?
a. The performance of the atomizer is not good
b. High oil temperature
c. Lack of heat fuel F.O.B
d. Low fuel rag position
e. Saya Tidak Tahu
12. What is the function of a disc in a purifier
a. Dirty oil disharge
b. Water supply
c. Temperature controller
d. Dirty oil separator
e. Saya Tidak Tahu
13. The following are forms of maintenance of the cooling engine on board, except
a. Clean lubricating oil
b. Clean the condenser
c. Check the v-belt tension
d. Bearing lubrication
e. Saya Tidak Tahu
14. What is the function of screw pump?
a. Used to pump fuel
b. Used to pump oil
c. Used to pump dirty oil (sludge)
d. Used to pump water
e. Saya Tidak Tahu
15. The function of the lubricating oil pump is
a. Blow down
b. To circulate lubricating oil to the main engine and auxiliary engines
c. To remove or remove water from the deck and also remove used water from showers, toilets,
laundry, food and minimum bars, kitchens, and so on
d. To filtering lubricating oil
e. Saya Tidak Tahu
16. Why does the scavenge space have to be drained?
a. To quickly cool the temperature
b. So as not to corrode
c. To be flammable
d. To be clean
e. Saya Tidak Tahu
17. Explain in full what is meant by “incidental maintenance”(Breakdown maintenance)?
a. Execution of work in accordance with routine maintenance based on operating time (working
hours)
 b. Maintenance work should be planned as far as possible taking into account operating
limitations
c. Work down every mont routine
d. Work done regularly every month
e. Saya Tidak Tahu
18. The part of the OWS that functions as a bilge water reservoir which is separated by a bilde
separator from oil deposits is called?
a. Coaliser
b. Bilge Separator
c. Bilge Pump
d. Disc
e. Saya Tidak Tahu
19. Why does every replacement of spare part need to be recorded on the date of replacement?
a. Do that we know the running hours
b. In order to know for the unlicky date
c. In order to know which one breaks faster
d. In order to know to the quality of the spart part
e. Saya Tidak Tahu
20. What is a propeller pitch control transmission?
a. An engine of the ship forward and backward using only the propeller blades
b. A ship’s engine that moves forward and backward whitout turning off the engine
c. An engine that moves forward and backward without turning off the engine
d. Merchanism of ships that move forward and ftl only uses a motor
e. Saya Tidak Tahu
21. What is meant by the term neutral welding?
a. Excess acetylene flame is used for welding hard solders
b. Flame occurs where the combustion during welding the ratio between the gas mixture and
acetylene is the same
c. The flame is overloaded and ocygen and is used to weld brass
d. A flame where only acetylene is used
e. Saya Tidak Tahu
22. What is the anchor bar transmission?
a. An engine that moves forward and backward without turning off the engine
b. A ship’s engine that moves forward and backward must first turn off
c. Merchanism of ships that move forward and aft only uses a motor
d. An engine of the ship forward and backward using only the propeller blades
e. Saya Tidak Tahu
23. In a 4-stroke 8-cylinder diesel engine, the firing order is as follows 1-5-7-3-8-4-2-6, so the correct
position of the cylynder is?
a. Cylinder 3 and cylinder 4
b. Cylinder 5 and cylinder 4
c. Cylinder 2 and cylinder 8
d. Cylinder 1 and cylinder 8
e. Saya Tidak Tahu
24. The following is the correct order of transferring fuel.
a. Start the pump, ,open the suction valve, open the discharge valve
b. Open the suction and discharge pump, open the faucet from the double bottom to the service,
start the pump and observe the pressure
 c. Open the discharge valve, start the pump, open the suction valve
d. Open the discharge valve, open the suction valve, start the pump
e. Saya Tidak Tahu
25. What the main engine rpm is still low, and the turbo has not worked optimally to supply the rinse
air, where is the rinse air taken from?
a. Open the scavenge to let the rinse air in
b. From the wind all amound
c. From the engine room
d. From the main engine blower
e. Saya Tidak Tahu
26. What do you know about the definition of incidental Maintenance?
a. The maintenance is carried out only when damage occurs
b. The maintenance is carried out in accordance with the condition od the existing spare parts
c. The maintenance is carried out according to the working hours of the service
d. Maintenance performed on important machining priorities
e. Saya Tidak Tahu
27. What is meant by re-calibrating?
a. It is a tool that serves to achiede the desired results
b. The possibility of the ability of a tool (instrument) to be able to do a job that is expected at a
certain time
c. Re-calibating means that equipment related to production and use of materials is calibrated
more often
d. It is a fool that serves to achieve the desired result
e. Saya Tidak Tahu
28. Why after overhaul the main engine must be tested before sailing?
a. Just make sure that the engine is running and there are no more problems
b. So that if there are things or components that don’t fit, they can be repaired immendiately
c. Make sure that everything is working normally and ready to sail
d. All answers are correct
e. Saya Tidak Tahu
29. If you are a 3rd engineer and have responsibility for a steam boiler, one day you forget to burn
manually and steam until the safety valve is more than working. But at that time the safety valve
did not work automatically, what did you do as a 3rd engineer?
a. Leaving because the safety valve auto is damaged
b. Pulling the safety valve manually and turning off the valve
c. Immediately report to the chief engineer
d. Run away immendiately afraid of an explosion
e. Saya Tidak Tahu
30. Choose one of the statements below which is not a FWG operating procedure?
a. Opens the brine overboard valve
b. Opens the ejector inlet valve
c. Blow up FWG
d. Starts the ejector pump
e. Saya Tidak Tahu
31. What causes the gray smoke on the main motor?
a. Incorrect fuel ratio
b. Lubricating oil that is no longer suitable for use
c. No compression in combustion chamber
 d. Fuel injection pressure is too low
e. Saya Tidak Tahu
32. What is the function of a ejector pump?
a. Used to pump dirty oil (sludge)
b. Used to pump water
c. Used to pump fuel
d. Used to sea water into Fresh water generator system
e. Saya Tidak Tahu
33. In a refrigeration machine, there is a lump of ice on the outside of the evaporator pipe, the thing to
do is
a. Clean the condenser
b. Fill freon
c. Defrosting
d. Refresh
e. Saya Tidak Tahu
34. Which of the following statements is the correct way to operate the cooling system?
a. Flow the condenser, check the low and high pressure and oil, operate the motor, open the
intake valve and press
b. Flow the condenser, open the suction valve and press the compressor, operate the condenser
motor, check low, and high pressure and oil
c. Check low and high pressure and oil, operate the compressor, open the suction valve and
press the compressor, operate the motor
d. Check low and high pressure and oil, open the suction valve and press the compressor operate
the compressor, drain the condenser
e. Saya Tidak Tahu
35. Pumps that move rotating can be classified as follows, except
a. Double acting plunger/piston pump means that each piston produces a stroke volume
b. Centrifugal pump
c. Gear pumps, these pumps are often used fir various types such as lubricating oil pumps, fuel
transfer pumps, and fuel for steam boilers
d. Wing pump, this pump is considered as a suction and pressure pump
e. Saya Tidak Tahu
36. Which of the following steps is correct in operating the purifier?
a. Open the water laucet,, Power on, close the water faucet, open the fuel faucet
b. Power on, open the water faucet, open the fuel faucet, close the water faucet
c. Open the water faucet, open the fuel faucet, power on, close the water faucet
d. Power on, open the fuel faucet, open the water faucet, close the water faucet
e. Saya Tidak Tahu
37. Why does it need to be turned before starrting the generator?
a. Let’s not get stuck
b. So that the lubricating oil can lubricate the engine parts first
c. To make sure it can spin
d. To be light when starting
e. Saya Tidak Tahu
38. A machine that can convert electric power into mechanical power is?
a. Dry battery
b. Electric motor
c. Dynamo
 d. Generator
e. Saya Tidak Tahu
39. Which of the following statements is not a chamshaft inspection procedure?
a. Observe the condition of the chamshaft from scratchesand wear
b. Turning the chamshaft with the turning gear
c. Measured the length of the chamshaft
d. Opening the chamshaft cover
e. Saya Tidak Tahu
40. Why is the piston ring and liner inspection held?
a. All answers are correct
b. To find out if the liner is cracked or not
c. To find out if the ring is broken or not
d. In order to know the condition of the piston rings
e. Saya Tidak Tahu
41. Why does the O-ring need to be given a molicot when installing?
a. To be strong
b. So that it doesn’t stick and is easy to remove during overhaul
c. So that it’s tight and doesn’t leak
d. To be sticky and durable
e. Saya Tidak Tahu
42. After the purifier is used and will be stopped, the steps that must be taken are
a. Power off
b. Blow up
c. Blow down
d. Brake
e. Saya Tidak Tahu
43. What is the possible caise of a Main Diesel diffiult to start, except ...
a. The spraying of fuel in the cylynder is late and less than perfect
b. Explanation air pressure is to low
c. Type of fuel used
d. Air starting valve stuck due to corrosion
e. Saya Tidak Tahu
44. The instrument used to measure engine speed is called?
a. Ecosounder
b. Tacometer
c. Manometer
d. Barometer
e. Saya Tidak Tahu
45. Which of the following statements is the correct way to operate the cooling system?
a. Flow the condenser, open the suction valve and press the compressor, operate the condenser
motor, check low and high pressure and oil
b. Check low and high pressure and oil, operate the cmpressor, open the suction valve and press
the compressor, operate the motor
c. Check low and high pessure and oil, open the suction valve and press the compressor, operate
the condenser, drain the condenser
d. Flow the condenserm check the low and high pressure and oil, operate the motor, open the
intake valve and press
e. Saya Tidak Tahu
46. The folloeing are pumps with reciprocating movement, except
a. Double acting plunger/piston pump means that every two steps produces one stroke volume
b. Gear pumps, these pumps are often used for various types such as lubricating oil pumps, fuel
transfer pumps, and fuel for steam boilers
c. Differential plunger.piston pump, this pump is a combination of single-acting or double-
acting pumps
d. Double acting plunger/piston pump means that each piston produces a stroke volume
e. Saya Tidak Tahu