SyncoFloor - EP - Waterbased STC 5713 SL

TECHNICAL DATA SHEET
SyncoFloor EP – Waterbased STC 5713 - SL
DESCRIPTION
SyncoFloor EP-Waterbased STC 5713 SL is a Environment friendly product based on a two
component Epoxy waterbased amine cured coating. SyncoFloor EP – Waterbased STC 5713
SL has good abrasion and good adhesion to concrete . The special feature of the SyncoFloor
STC 5713 SL it can be used as a Primer and a top coat ( Single Coat System ) or using SPR
5701 as Primer . If SyncoFloor EP – Waterbased STC 5713 SLis combined with
SyncoCrete PU – Hybrid Waterbased SL 1201 as Primer so Breathable system will be
formed on concrete surfaces which can tolerate a high humidity floor.
RECOMMENDED USE
SyncoFloor EP – Waterbased STC 5713 SL is suitable for One Coat System or as Body coat
and Top coat after SyncoCrete PU - Hybrid Waterbased SL 1201 ( Breathable – System )
SPECIALS – CHARACTERISTICS
• Moisture tolerance
• Self-smoothing
• Water dilutable
• Odorless
• Low Viscosity
• Improves the adhesion of Top Coat
• Good chemical resistant.
• Excellent abrasion resistance
• Easy application
BASIC DATA
Colour Color
Gloss Level 30 % - 50 %
1
Volume Solid ~ 80 %
Dry Film Thickness 1.0 mm or 1000 Microns
Theoretical Spreading Rate / 1.7 kg/m2 for 1000 microns

Coverage
Pack Size A : B = 10 kgs : 10 kgs
Mixing Ratio A:B =1:1
SG mix ~ 1.35 gr/ml
Shelf Life At least 12 months when stored cool and dry
INSTRUCTION FOR USE
Surface preparation
Thorough surface preparation is vital. Concrete shall be clean, dry and free of all contaminant
such as dirt, oil grease etc. and concrete structurally sound and sufficient compressive strength
min. 30 N/mm2 with a min. pull off strength of 1.5 N/mm2. For best results Syncoat
recommends mechanical preparation techniques. (For example, metal grinding or using
diamond/resin pad).
New concrete floors

Should be at least 14 days old before proceeding with SyncoFloor EP – Waterbased STC
5713 SL application. Laitance and deposits on new concrete floors are best removed by light
grit blasting, mechanical grinding. On smaller areas thorough etching may be considered.
After etching the floor, it should be thoroughly washed with clean water and then let to dry.
Old concrete floors

Mechanical cleaning methods are strongly recommended on old concrete floors, particularly
where heavy contamination by oil and grease has occurred or existing coatings are present.
These may well have been absorbed several millimeters deep into the concrete. To ensure
good adhesion all contamination should be removed and the surface thoroughly cleaned of all
dust and loose debris. A thorough detergent wash is also recommended followed by thorough
cleaning with clean water and mopping it off to a dry state.
Mixing
Add the entire contents of the hardener tin to the base and mix thoroughly for 3 mins. until
homogeneous, using a slow speed drill ( 200 - 400 rpm) fitted with a suitable mixing paddle.
2
Application
Once mixed the primer should be applied immediately in a thin continuous film to the clean
prepared surface. Work the primer into the surface using a notch or metal trowel and follow
by spiked roller. Excess application and puddling should be avoided. On porous surfaces.
SyncoFloor EP – Watebased STC 5713 SL will be absorbed very quickly.
Thinner
Water
Mixing Ratio
Base : Hardener = 1 : 1 ( by weight )
Cleaner / Cleaning Solvent

Water
ADDITIONAL DATA Overcoating Intervals

Temperature 250C 320C
Minimum 4 hours 3-4 hours
Maximum 8 hours 6 hours
Drying / Curing Time

Temperature Touch Dry Through Dry Full Cure
250C 2 hours 4 hours
320C 1 hour 2 hours
Pot Life
Temperature Pot Life
320C 30 minutes
3
STORAGE AND HANDLING
The product must be stored in accordance with national regulation. Storage conditions are to
keep the containers in a dry, cool, well ventilated space and away from the source of heat and
ignition. Containers must be kept tightly closed. Handle with care, stir well before use.
SAFETY PRECAUTIONS
Keep away from heat, spark and open flames. Avoid breathing of vapour on skin and eye
contact. Keep container closed and store in a cool, ventilated area when not in use.
Proper ventilation and protective measures must be provided during mixing, application and
drying, to keep vapour concentration within safe limits and to protect against toxic hazard.
Necessary safety equipment must be used and ventilation requirements carefully observed,
especially in confined and enclosed space, such as tank interior and building.
DISCLAIMERS
The information in this technical data sheet is given to the best of our knowledge based on laboratory testing and
practical experience. If the product is used under condition beyond our control, we cannot guarantee anything
but the quality of the product itself. The information in this technical data sheet is liable for modification from
time to time in the light of experience and our policy of continuous product development, and without further
notice. Dec. - 2021

SyncoFloor - EP - Waterbased STC 5713 SL

Uploaded by

SyncoFloor - EP - Waterbased STC 5713 SL

Uploaded by

TECHNICAL DATA SHEET

SyncoFloor EP – Waterbased STC 5713 - SL

Dry Film Thickness 1.0 mm or 1000 Microns

Theoretical Spreading Rate / 1.7 kg/m2 for 1000 microns

Pack Size A : B = 10 kgs : 10 kgs

Mixing Ratio A:B =1:1

SG mix ~ 1.35 gr/ml

Shelf Life At least 12 months when stored cool and dry

INSTRUCTION FOR USE

New concrete floors

Old concrete floors

Cleaner / Cleaning Solvent

ADDITIONAL DATA Overcoating Intervals

Minimum 4 hours 3-4 hours

Maximum 8 hours 6 hours

Drying / Curing Time

250C 2 hours 4 hours

320C 1 hour 2 hours

You might also like