NEW High-Accuracy Digital Contact Sensor

GT2 Series

I-SERIES
Intel lig e nt s e n s or

The GT2 Series is now available in pencil type models!

High-accuracy and an absolute measurement are possible with a slim ø8 ø0.31" body

GT2 Series
 Unique technology allowing
a compact sensor head.
The Scale Shot System in the GT2 Series improves
upon the technology of conventional contact
sensors and is now concentrated into a pencil-type
sensor head.

2
 SCALE SHOT SYSTEM II
Display resolution 0.1 μm 0.004 Mil

Accuracy 1 μm 0.04 Mil

The ø8 mm ø0.31" sensor head is equipped with KEYENCE’s proprietary Scale Shot System II, which allows it to
achieve the highest accuracy in its class throughout its entire measurement range. It also overcomes the
disadvantages of conventional methods such as tracking errors and not knowing absolute position.

TOUGH & RUGGED CONSTRUCTION

NEMA Type 13/IP67G

100 million cycles detecting durability

PUR cable

Complies with NEMA Type 13/IP67G oil resistance protection standards. These sensor heads can be used in wet and
dusty environments, and now even in environments with splashing oil. The sensor head also clears a detecting
durability of 100 million cycles with its long lasting linear ball bearings.

MULTI-SENSOR UNIT
5 heads can connect to 1 amplifier unit

A multi-sensor amplifier unit has been added to our line up which allows up to 5 sensor heads to connect to 1 amplifier
unit. A maximum of 3 amplifier units and 15 sensor heads can be simultaneously connected to support multi-point
applications. Also, larger systems can easily be constructed using the communication units.

3
 FULL-RANGE,
HIGH-ACCURACY PENCIL-TYPE
Combines a slim ø8 mm ø0.31" body with high-accuracy measurements
The evolutionary Scale Shot System II is enclosed in the slim ø8 mm ø0.31" body
through the use of newly developed technology for the transmitter, receiver, and CPU.
The sensor head features high accuracy while overcoming the disadvantages of
conventional contact sensors such as tracking errors and unknown absolute position.

ø8 mm ø0.31"

High-resolution CMOS

Absolute value glass scale

HL-LED

SCALE SHOT SYSTEM II

The absolute value glass scale, with different patterns according to position, is captured
at high speed with the high-resolution CMOS sensor. This detection principle reads the
absolute position information from the slit pattern engraved on the scale. It is the first of
its kind in the world.

4
 PROBLEMS WITH CONVENTIONAL TYPES

SCALE (PULSE-COUNT) METHOD

TRACKING ERRORS ABSOLUTE POSITION UNKNOWN

Tracking errors in measurement values result from sudden impact. The origin point must be adjusted before operation.

DIFFERENTIAL TRANSFORMER METHOD

UNSTABLE ACCURACY
POOR TEMPERATURE CHARACTERISTICS
THROUGHOUT ENTIRE MEASURING RANGE

Unstable accuracy at the top and bottom of the measuring range. Measurement values deviate morning, noon, and night.

LARGE BODY

Installation space must be considered.

RESOLVED WITH THE SCALE SHOT SYSTEM II

Absolute measurement with the highest accuracy in its class

DISPLAY RESOLUTION ACCURACY

0.1 μm 0.004 Mil 1 μm 0.04 Mil

THE NEWLY DEVELOPED FEATURES THAT MAKE THE SCALE SHOT SYSTEM II POSSIBLE

HL-LED HI G H - R E S O L UT I O N C M O S I-PROCESSOR

A newly developed LED that is a point light An imaging element with twice the pixels of a A custom IC equipped with new algorithms
source and capable of producing even conventional imaging element that can that can perform high-speed, high-resolution
intensity with a brightness 9-times that of a receive the LED light passed through the arithmetic processing of the output signal
conventional LED. absolute value glass scale with high sent from the CMOS sensor.
* HL = High luminance sensitivity, increase the resolution, and
create the output signal.

5
 H IG H E N V I R O N MENTAL R ES IS TANCE

First in class

NEMA Type 13
IP67G
*GT2-P12K(F)/P12(F)

USABLE IN OILY ENVIRONMENTS

The sensor head, including the connector and cable section, complies with
two standards - NEMA Type 13 and IP67G. The sensor head can be
mounted almost anywhere, even in environments with splashing water or oil.

❚ Oil-resistant connector and cable

Both the sensor head and connector comply with NEMA Type 13/IP67G. Extremely
oil-resistant PUR (polyurethane) is used for the GT2-sensor cable to reduce the risk
of oil penetration.

❚ Seamless construction
The sensor body is cast in one piece for seamless outer construction.
Corrosion from water and oil is reduced due to the fully enclosed structure.

NEMA Type 13
NEMA (National Electrical Manufactures Association) specifies the classification and description
of enclosures for electrical equipment. The classification is represented as the "Type", and
NEMA Type 13 is designed to provide a degree of protection against the ingress of oil.

IP67G
IP67G represents the enclosure rating for electronic devices as defined by the JIS (Japanese
Industrial Standards). IP67G represents “IP67” as defined by the IEC (International
Electrotechnical Commission) with “G” added for its oil resistance.

6
 H I G H E N D U R AN C E

EXTRAORDINARY DETECTING DURABILITY

100 million cycles *GT2-P12K(F)/P12(F)

A detecting durability of 100 million cycles has been achieved by using new high-strength linear ball bearings in the spindle.
This can greatly reduce maintenance costs and replacement efforts.

❚ Long lasting linear ball bearings

The all stainless steel construction of the spindle structure (shaft &
bearings) reduced the weight of the GT2. Through these weight savings,
wear due to friction inside the spindle has been minimized. This has
dramatically increased endurance.

Linear ball
bearing used

FLEXIBLE FREE-CUT ROBOT CABLE & OIL-RESISTANT RELAY CONNECTOR

The cable between the relay connector and amplifier unit uses a flexible free-cut robot cable that withstands continuous bending.
This allows the sensor to be installed on moving equipment. A detachable relay connector system is also used. This can greatly
reduce replacement work during maintenance.

❚ Flexible free-cut robot cable ❚ Detachable sensor head cable

Withstands bending 20 million times
without breaking (Typical usage)

Load (W): 250 g

Bend radius: 50 mm 1.97" 90°
Bending rate:
30 times/minute
(1 time includes left to right to original position)

FREE CUT! R

7
 V ERS AT I L E D ET EC TI O N M O D E S S U P P O RT A LL AP P L I CATI O N S

AUTO MO BILE S

Flatness measurement of engine block Door beam deformation check Disc assembly inspection

Camshaft runout measurement Side mirror angle inspection Oil pan flatness measurement

ME TALS

Bearing assembly inspection Mill roll gap management Gear assembly inspection

E Q UIP ME N T

Machine tool stroke management Assembly equipment press fitting Product chucking confirmation
inspection

8
 E LE C TR O N IC S

Battery flatness check Smartphone chassis flatness inspection Board assembly check

Hard disk frame assembly inspection Hard disk clamp parallelism inspection Chassis frame warpage inspection

S EM IC O N D UC TO R S/LIQ UID C RY STALS

Polisher height control Liquid crystal panel flatness inspection Wafer thickness measurement

FO O D /P R IN TIN G

Double label stickers detection Workpiece suction check Double feed detection

9
 S Y STE M C O N FIGU R ATIO N

SAVE WIRING TIME WITH OPEN FIELD NETWORK SUPPORT

ASSEMBLY EQUIPMENT INSPECTION EQUIPMENT

The GT2 Series supports various networks with its

lineup of communication units.

❚ DL Series lineup

EtherNet/IP DL-EP1
OPEN FIELD NETWORK

DeviceNet DL-DN1
COMMUNICATIONS

PROFIBUS DL-PD1

CC-Link DL-CL1

RS-232C DL-RS1A
communication

BCD output DL-RB1A

10
❚ Batch read and change settings for multiple amplifier units
Batch transmit data for a maximum of 15 units.
Settings can also be changed from a PC or PLC which leads to reduced setup time.

Data Data

Control Control

❚ Further wiring and space savings with the multi-sensor unit NEW

Up to 5 sensor heads can be connected to 1 multi-sensor amplifier unit. Up to 3 units can

be linked, which allows for a maximum of 15 connected sensor heads.

❚ Reduced wiring and installation

When more units are used in combination with each other, more wiring is required.
If communicating with the DL Series, this unit will send data to the PLC and only two wires are required to supply power to the
main unit.

Reduce cable fabrication work

Reduce work wiring into terminal blocks

This portion of the wiring is unnecessary

No terminal blocks required

11
 E ASE OF U SE

COST REDUCING MOUNTING METHODS

❚ Greatly reduces design and fabrication time

The sensor can be mounted almost anywhere thanks to ø8 mm ø0.31" slim body that can be mounted anywhere along its body.
If you use one of the dedicated brackets, you do not need to fabricate a slotted jig. The flange type can also be directly mounted by
simply drilling a ø10 mm ø0.39" hole.

CONVENTIONAL GT2

Bracket mounting Flange type

Mountable
throughout
full range

A slotted jig must be

When using mounting bracket F
fabricated and mounted. Simply drill a ø10 mm ø0.39" hole.
* The flange type combines the sensor head and the bracket.

❚ Air push type requires no drive mechanism

Measurements can be performed with the sensor head secured in place, so no mechanism is required to move the sensor head
itself. This allows for space-saving installation which can greatly reduce costs at initial setup. Plus any worries about variations in
accuracy due to the jig are eliminated.

External diameter THE AIR PUSH TYPE USES AIR TO EXTEND THE SPINDLE
ø4 ø0.16"
Air tube CONVENTIONAL METHOD GT2 AIR PUSH TYPE
Cable

Linear guide
Slotted jig
Stopper

Air push

Spindle

No jig required

12
REDUCE COSTS WITH MULTI-FUNCTION AMPLIFIER UNITS

❚ Simple calculations
A variety of detection modes are standard.
Calculations between additional amplifier units can be easily configured simply by selecting the desired mode.

Thickness [SHAFT DIAMETER MEASUREMENT]

Positioning the target between two sensor heads will display the outer diameter.

Main unit Expansion unit Calculation result

Degree of [FLATNESS CHECK]

flatness By subtracting the minimum value from the maximum value the flatness will be displayed.

Main unit Expansion unit Expansion unit Expansion unit

Calculation result

Maximum value Minumum value

VERSATILE DETECTION MODES SUPPORT ALL APPLICATIONS

SINGLE HEAD MULTIPLE HEADS/when additional amplifier units are installed (application modes)
Degree of Reference
STD P-H B-H P-P Maximum Minimum Average Twist Warpage Thickness
flatness difference

Standard Peak hold Bottom hold Peak to peak

❚ Total cost reductions

PLC programming or an analog input card, which was required with LVDTs, is no longer necessary.
This leads to cost reductions.

CONVENTIONAL METHOD GT2 SOLUTION

+ EASY WAY + = Done

Display

= Done

+ + =
EASY WAY + Done
Analog card PLC programming

13
 SEN S OR HEAD L I N E U P
Select the sensor head by measuring range, appearance, resolution, accuracy, mounting method, and measuring force

Pencil type NEW

Measuring Standard Flange

Accuracy
range Standard Low stress Standard

GT2-P12K GT2-P12KL GT2-P12KF

High-accuracy

Resolution 0.1 μm
0.004 Mil
Accuracy 1 μm
0.04 Mil

12 mm
0.47"
GT2-P12 GT2-P12L GT2-P12F

General-purpose

Resolution 0.5 μm
0.02 Mil
Accuracy 2 μm
0.08 Mil

Sensor head cable Select by the distance between the sensor head and the amplifier unit, the environment, and the mounting method

NEW Oil-resistant cable (straight)*1 Standard cable (straight) Standard cable (L-shaped)*2

GT2-CHP2M 2 m 6.6' GT2-CH2M 2 m 6.6' GT2-CHL2M 2 m 6.6'

GT2-CHP5M 5 m 16.4' GT2-CH5M 5 m 16.4' GT2-CHL5M 5 m 16.4'

GT2-CHP10M 10 m 32.8' GT2-CH10M 10 m 32.8' GT2-CHL10M 10 m 32.8'

GT2-CH20M 20 m 65.6' GT2-CHL20M 20 m 65.6'

*1 To satisfy NEMA Type 13/IP67G with the pencil type, the oil-resistant cable must be used.
*2 Can only be used with the 12 mm 0.47" type.

14
Box type

Measuring Standard Flange Air push

Accuracy
range Standard Low stress Standard Low stress Standard Low stress

GT2-H12K GT2-H12KL GT2-H12KF GT2-H12KLF GT2-A12K GT2-A12KL

High-accuracy

Resolution 0.1 μm
0.004 Mil
Accuracy 1 μm
0.04 Mil

12 mm
0.47" GT2-H12 GT2-H12L GT2-H12F GT2-H12LF GT2-A12 GT2-A12L

General-purpose

Resolution 0.5 μm
0.02 Mil
Accuracy 2 μm
0.08 Mil

GT2-H32 GT2-H32L GT2-A32

General-purpose
32 mm
- - -
1.26" Resolution 0.5 μm 0.02 Mil
Accuracy 3 μm 0.12 Mil

GT2-H50 GT2-A50

General-purpose

50 mm Resolution 0.5 μm
- - - -
1.97" 0.02 Mil
Accuracy 3.5 μm
0.14 Mil

15
 AMP L I F I ER U NI T LI N E U P
Select according to the output method, mounting method, and number of connected units

Amplifier unit type Appearance/model

DIN-rail mount type Panel mount type 5-output function

Judges the 5 statuses HH/High/Go/Low/LL
Bank function
Registers limit setting values and preset values in up to 4 different groups
Calculation functions using expansion units
Enables calculations such as maximum value, minimum value, and degree of
flatness
Judgment output
(5 outputs)
Loose wire Connector Panel

NPN GT2-71N GT2-71CN GT2-75N

Main unit
PNP GT2-71P GT2-71CP GT2-75P
NPN GT2-72N GT2-72CN GT2-76N
Connector type Expansion unit
PNP GT2-72P GT2-72CP GT2-76P

DIN-rail mount type

3-output function
Judges the 3 statuses High/Go/Low
Bank function
Registers limit setting values and preset values in up to 4 different groups
Calculation functions using expansion units
Analog output
Enables calculations such as maximum value, minimum value, and degree of
(4 to 20 mA) flatness

Connector
NPN GT2-71MCN
Connector type Main unit
PNP GT2-71MCP

DIN-rail mount type

Minimum phase difference selection

[0.5/2.5/5/25 μs]
Capable of batch output of position information.
Pulse output
Loose wire
Increment/decrement direction
Main unit NPN GT2-71D
Pulse output resolution
Minimum phase difference

Panel mount type

Easy operation with a large display and buttons.
Up to 11 sensor heads can be connected using the expansion board.
* With only the main body, up to 2 sensor heads can be connected

Connector
Large display
NPN GT2-100N
Main body
PNP GT2-100P
Expansion board NPN GT2-E3N
(3 sensor heads/1 board) PNP GT2-E3P

DIN-rail mount type

Up to 5 sensor heads can be connected to 1 amplifier unit

Up to 15 sensor heads can be connected by adding 2 expansion units
NEW * A communication unit (DL Series) is required for output.
Multi-sensor Multi-head connection
amplifier unit
Main unit GT2-500
Expansion unit GT2-550

16
 COM MU NI C ATI O N U N I T LI N E U P

Communication Judgment Measurement Modify

Model Appearance Control input Remarks
method result readout value readout tolerance value

Uses cyclic communication.

EtherNet/IP DL-EP1 A communication program does not need to be created.
Change settings using explicit message communication.

Uses I/O communication.

DeviceNet DL-DN1 A communication program does not need to be created.
Change settings using explicit message communication.

Uses cyclic transmissions.

PROFIBUS DL-PD1 A communication program does not need to be created.
Change settings using the DP-V1 service.

Uses cyclic transmissions.

CC-Link DL-CL1 A communication program does not need to be created.
Change settings using handshake control.

Uses RS-232C communication.

RS-232C DL-RS1A
Communicate by creating a communication program.

Measurement values are synchronized and updated with

BCD DL-RB1A the input terminal or automatically updated by timer.
Values are synchronized and read by strobe output.

The ◎ symbol indicates wire savings and communication program creation is not required. 〇=Can be accessed by creating a communication program. ×=Cannot be accessed.

SY S T EM C ONF I G U R ATI O N
Adding expansion units to the main unit
Expand with the side connector.

To add a unit, please use the Main unit

Expansion unit
separately available end unit
(OP-26751).

Connector

Main unit
GT2-71N/P Expand with the cable included with the expansion unit.
GT2-71CN/CP
GT2-71MCN/MCP Expansion units To add a unit, mount vertically with
the main unit as the top unit.
GT2-75N/P GT2-72N/P Expansion cable
*The GT2-71D cannot be GT2-72CN/CP
added and used. GT2-76N/P
DL Series
*Expansion units * To mount horizontally, the separately available OP-35361
communication unit
expandable up to 14 units (expansion cable 300 mm 11.81") is required.
for 1 main unit.

17
 OP T I O NS

Mounting brackets (GT2 12 mm 0.47" type mounting brackets)

GENERAL PURPOSE TYPE SIDE MOUNTING TYPE

Mounting bracket A Mounting bracket B
OP-76874 OP-76875
Drill a ø10 ø0.39" hole, and secure
ecure the mounting bracket
bracket. For
mounting bracket D, drill a ø14 ø0.55" hole, and secure the
mounting bracket.

* The mounting method is the same for mounting bracket A and mounting bracket C.
* When using the GT2-H32L with the contact probe pointed up, use the mounting
holes on the main body.

REINFORCED HOLDING FORCE TYPE SIDE MOUNTING TYPE

Mounting bracket C Mounting bracket E
OP-84396 Vibration resistant OP-87220 Reinforced holding force

NEW
Horizontal mounting.

COUPLED MOUNTING TYPE

Mounting bracket F
OP-87863
The sensor head mounting
pitch is 10 mm 0.39" when
the brackets are mounted to
Mounting bracket (GT2 32 mm 1.26"/50 mm 1.97" type mounting brackets)
the same surface and 9 mm
0.35" when the brackets are
mounted front and back.

REINFORCED HOLDING FORCE TYPE

Mounting bracket D
OP-84327 Vibration resistant

Contacts

SUPER-TOUGH*2 FLAT PLATE FLUOROCARBON RESIN

STANDARD*1 OP-77682 OP-77679 ROLLER OP-80228
OP-77678 Uses a super-tough alloy, For objects with a curved or pointed OP-77680 Made from material that is unlikely to
For standard measurements for high-accuracy measurements surface For moving objects damage the target’s surface

CERAMIC OFFSET ROLLER (HIGH-ACCURACY)

OP-81970 NEEDLE OP-77683 SPACER OP-93332
To electrically insulate the sensor from the OP-77681 For multiple measurements of a small OP-77684 For use when the roller eccentricity is a
target To measure in tight locations object Extends the spindle 12.2 mm 0.48" concern

*1 Standard on the GT2-P12(L/F), GT2-H(A)12(L/F/LF), GT2-H(A)32(L), GT2-H(A)50

*2 Standard on the GT2-P12K(L/F), GT2-H(A)12K(L/F/LF)

18
Dust boots
NEW

STANDARD DUST BOOT

(material: NBR)
For 12 mm 0.47" OP-84332 FLUOROCARBON RUBBER DUST BOOT
For 32 mm 1.26" OP-84459 (material: FKM)
For 50 mm 1.97" OP-84460 For 12 mm 0.47" OP-87859

Amplifier unit options (for DIN-rail mount/panel mount types)

EXPANSION CABLE
300 mm 11.81"
DIN-RAIL TYPE SOCKET CABLE PANEL MOUNT OP-35361
AMPLIFIER UNIT BRACKET END UNIT (2 count) GT2-CA2M/CA10M OP-84394 To connect panel types horizontally, and to
OP-76877 OP-26751 Required with the connector type Included with the panel type connect the panel type and the DL

Amplifier unit options (for the GT2-100N/100P)

EXPANSION BOARD BRACKET 20-PIN MIL CONNECTOR 30-PIN MIL CONNECTOR

GT2-E3N/E3P OP-84331 OP-22185 OP-84456
Can expand 3 sensor heads per 1 board To mount on a rack For 1 to 2 sensor heads For the expansion board

CONTACTS CONTACTS EXPANSION CABLE

for AWG24 to 22, 200 count for AWG28 to 26, 200 count SPECIAL CRIMPING TOOL 300 mm 11.81"
OP-22186 OP-30594 OP-21734 OP-35361
For OP-22185/84456 For OP-22185/84456 For crimping OP-22186/30594 Use when connecting the DL

Others

2-ø4 ø0.16"

CONNECTORS
Replacements for connecting to the
SPEED CONTROLLER LIFT LEVER SENSOR HEAD RELAY CABLE amplifier unit
OP-82133 OP-84397 OP-87431/87432/87433 OP-84338 (2 count)
For adjusting the air for air push type Manually lifts the spindle M8-M8 relay cable 3.5 m 11.5'/7.5 m 24.6'/9.0 m 29.5' For the sensor head cable

19
 SP EC I F I C AT I O NS

Pencil type (High-accuracy type) NEW

Model GT2-P12K GT2-P12KF GT2-P12KL

Appearance

Detection system Scale Shot System II, absolute (no tracking errors) type
Measuring range 12 mm 0.47"
Resolution 0.1 μm 0.004 Mil
Indicated accuracy*1 1 μm 0.04 Mil (P-P)
Downward mounting 1.0 N 0.2 N
Measuring
Side mounting 0.95 N 0.15 N
force *2
Upward mounting 0.9 N 0.1 N
Sampling cycle 4 ms
Mechanical response*1 10 Hz 4 Hz
Operation indicator 2-color LED (red, green)
IP67G (JIS)*3
Enclosure rating IP67 (IEC) -
NEMA Type 13*3
Environmental
Ambient temperature -10 to +55°C 14 to 131°F (No freezing)
resistance
Relative humidity 35 to 85% RH (No condensation)
Vibration 10 to 55 Hz Double amplitude 1.5 mm 0.06" in the X, Y, Z axis directions respectively, 2 hours
Impact resistance 1000 m/s 2 (IEC60068-2-27)
Main body Main body case: SUS 303, Status indicator: PET, Sensor head-relay connector cable: PUR, Relay connector: PBT
Materials Dustboot NBR -
Contact*4 SUS304, cemented tungsten carbide
Sensor head cable Optional (connect to relay connector)
Weight (not including cable)*5 Approx. 35 g Approx. 45 g Approx. 35 g

*1 Value when the ambient temperature is 20°C 68°F. *2 Representative value at the center of the measuring range. The measuring force when using OP-87859 is the above value +0.4 N.
*3 When an M8 oil-resistant cable (GT2-CHP2M/CHP5M/CHP10M) is used for the sensor head cable. *4 Contacts are available as options sold separately. *5 Including the relay connector.
Note: You may not be able to connect the sensor head to the amplifier unit depending on when the amplifier unit was purchased.
For details, contact your local sales office.

Pencil type (General purpose type) NEW

Model GT2-P12 GT2-P12F GT2-P12L

Appearance

Detection system Scale Shot System II, absolute (no tracking errors) type
Measuring range 12 mm 0.47"
Resolution 0.5 μm 0.02 Mil
Indicated accuracy*1 2 μm 0.08 Mil (P-P)
Downward mounting 1.0 N 0.2 N
Measuring
Side mounting 0.95 N 0.15 N
force*2
Upward mounting 0.9 N 0.1 N
Sampling cycle 4 ms
Mechanical response*1 10 Hz 4 Hz
Operation indicator 2-color LED (red, green)
IP67G (JIS)*3
Enclosure rating IP67 (IEC) -
NEMA Type 13*3
Environmental
Ambient temperature -10 to +55°C 14 to 131°F (No freezing)
resistance
Relative humidity 35 to 85% RH (No condensation)
Vibration 10 to 55 Hz Double amplitude 1.5 mm 0.06" in the X, Y, Z axis directions respectively, 2 hours
Impact resistance 1000 m/s 2 (IEC60068-2-27)
Main body Main body case: SUS 303, Status indicator: PET, Sensor head-relay connector cable: PUR, Relay connector: PBT
Materials Dustboot NBR -
Contact*4 SUS304, SUS440C
Sensor head cable Optional (connect to relay connector)
Weight (not including cable)*5 Approx. 35 g Approx. 45 g Approx. 35 g

*1 Value when the ambient temperature is 20°C 68°F. *2 Representative value at the center of the measuring range. The measuring force when using OP-87859 is the above value +0.4 N.
*3 When an M8 oil-resistant cable (GT2-CHP2M/CHP5M/CHP10M) is used for the sensor head cable. *4 Contacts are available as options sold separately. *5 Including the relay connector.
Note: You may not be able to connect the sensor head to the amplifier unit depending on when the amplifier unit was purchased.
For details, contact your local sales office.

20
Box type
Model GT2-H12K GT2-H12KF GT2-H12KL GT2-H12KLF GT2-H12 GT2-H12F GT2-H12L GT2-H12LF

Appearance

Detection system Scale Shot System, absolute (no tracking errors) type
Measuring range 12 mm 0.47"
Resolution 0.1 μm 0.004 Mil 0.5 μm 0.02 Mil
Indicated accuracy*1 1 μm 0.04 Mil (P-P) 2 μm 0.08 Mil (P-P)
Downward mounting 1.0 N 0.4 N 1.0 N 0.4 N
Measuring
Side mounting 0.9 N 0.3 N 0.9 N 0.3 N
force *2
Upward mounting 0.8 N 0.2 N 0.8 N 0.2 N
Sampling cycle 1 ms
Mechanical response*1 10 Hz 4 Hz 10 Hz 4 Hz
Operation indicator 2-color LED (red, green)
Enclosure rating IP67 (IEC) - IP67 (IEC) -
Ambient temperature -10 to +55°C 14 to 131°F (No freezing)
Environmental
Relative humidity 35 to 85% RH (No condensation)
resistance
Vibration 10 to 55 Hz Double amplitude 1.5 mm 0.06" in the X, Y, Z axis directions respectively, 2 hours
Impact resistance 1000 m/s 2 (IEC60068-2-27)
Main body Main body case: die-cast zinc, Indicator: polyarylate (PAR)
Materials Dustboot NBR - NBR -
Contact*3 SUS304, cemented tungsten carbide SUS304, SUS440C
Sensor head cable Optional (connect to the M8 connector)
Weight (not including cable) Approx. 95 g Approx. 100 g Approx. 95 g Approx. 100 g Approx. 95 g Approx. 100 g Approx. 95 g Approx. 100 g
*1 Value when the ambient temperature is 20°C 68°F.
*2 Representative value at the center of the measuring range. Please note that the measuring force varies by the installation state of the dust boot.
*3 Contacts are available as options sold separately.

Box type (long range type)

Model GT2-H32 GT2-H32L GT2-H50

Appearance

Detection system Scale Shot System, absolute (no tracking errors) type
Measuring range 32 mm 1.26" 50 mm 1.97"
Resolution 0.5 μm 0.02 Mil
Indicated accuracy*1 3 μm 0.12 Mil (P-P) 3.5 μm 0.14 Mil (P-P)
Downward mounting 2.1 N 1.2 N 3.2 N
Measuring
Side mounting 1.8 N 0.9 N 2.8 N
force *2
Upward mounting 1.5 N 0.6 N 2.4 N
Sampling cycle 1 ms
Mechanical response*1 6 Hz 5 Hz 7 Hz
Operation indicator 2-color LED (red, green)
Enclosure rating IP67 (IEC) - IP67 (IEC)
Environmental Ambient temperature -10 to 55°C 14 to 131°F (No freezing)
resistance Relative humidity 35 to 85% RH (No condensation)
Vibration 10 to 55 Hz Double amplitude 1.5 mm 0.06" in the X, Y, Z axis directions respectively, 2 hours
Main body Main body case: die-cast zinc, Indicator: polyarylate (PAR)
Materials Dustboot NBR - NBR
Contact*3 SUS304, SUS440C
Sensor head cable Optional (connect to the M8 connector)
Weight (not including cable) Approx. 270 g Approx. 320 g
*1 Value when the ambient temperature is 20°C 68°F.
*2 Representative value at the center of the measuring range. Please note that the measuring force varies by the installation state of the dust boot.
*3 Contacts are available as options sold separately.

21
 SP EC I F I C AT I O NS

Box type (air push type)

Model GT2-A12K GT2-A12KL GT2-A12 GT2-A12L

Appearance

Detection system Scale Shot System, absolute (no tracking errors) type
Measuring range 12 mm 0.47"
Resolution 0.1 μm 0.004 Mil 0.5 μm 0.02 Mil
Indicated accuracy *1 1 μm 0.04 Mil (P-P) 2 μm 0.08 Mil (P-P)
Downward mounting 1.2 N 0.4 N 1.2 N 0.4 N
Measuring
Side mounting 1.1 N 0.3 N 1.1 N 0.3 N
force*2
Upward mounting 1.0 N 0.2 N 1.0 N 0.2 N
Sampling cycle 1 ms
Applied pressure range 0.25 MPa to 0.50 MPa
Pressure resistance 1 MPa
Fluid used Dry air
Operation indicator 2-color LED (red, green)
Enclosure rating IP67 (IEC)*3 - IP67 (IEC)*3 -
Ambient temperature 0 to +55°C 32 to 131°F (No freezing)
Environmental
Relative humidity 35 to 85% RH (No condensation)
resistance
Vibration 10 to 55 Hz Double amplitude 1.5 mm 0.06" in the X, Y, Z axis directions respectively, 2 hours
Impact resistance 1000 m/s 2 (IEC60068-2-27)
Main body Main body case: die-cast zinc, Cylinder section: aluminum alloy, Air joint resin: polyacetal, Air joint metal: nickel-plated brass, Indicator: polyarylate (PAR)
Materials Dustboot NBR - NBR -
Contact *4 SUS304, cemented tungsten carbide SUS304, SUS440C
Sensor head cable Optional (connect to the M8 connector)
Weight (not including cable) Approx. 145 g

*1 Value when the ambient temperature is 20°C 68°F. *2 Representative value at the center of the measuring range. Please note that the measuring force varies by the installation state of the dust boot.
*3 Connect an exhaust joint to the air tube and ensure that foreign matter does not enter the tube from joint. *4 Contacts are available as options sold separately.

Box type (air push type/long range type)

Model GT2-A32 GT2-A50

Appearance

Detection system Scale Shot System, absolute (no tracking errors) type
Measuring range 32 mm 1.26" 50 mm 1.97"
Resolution 0.5 μm 0.02 Mil
Indicated accuracy *1 3 μm 0.12 Mil (P-P) 3.5 μm 0.14 Mil (P-P)
Downward mounting 2.1 N 3.2 N
Measuring
Side mounting 1.8 N 2.8 N
force*2
Upward mounting 1.5 N 2.4 N
Sampling cycle 1 ms
Applied pressure range 0.25 MPa to 0.50 MPa
Pressure resistance 1 MPa
Fluid used Dry air
Operation indicator 2-color LED (red, green)
Enclosure rating IP67 (IEC)*3
Environmental Ambient temperature 0 to +55°C 32 to 131°F (No freezing)
resistance Relative humidity 35 to 85% RH (No condensation)
Vibration*4 10 to 55 Hz Double amplitude 1.5 mm 0.06" in the X, Y, Z axis directions respectively, 2 hours
Main body Main body case: die-cast zinc, Cylinder section: aluminum alloy, Air joint resin: polyacetal, Air joint metal: nickel-plated brass, Indicator: polyarylate (PAR)
Materials Dustboot NBR
Contact *5 SUS304, SUS440C
Sensor head cable Optional (connect to the M8 connector)
Weight (not including cable) Approx. 340 g Approx. 405 g

*1 Value when the ambient temperature is 20°C 68°F. *2 Representative value at the center of the measuring range. Please note that the measuring force varies by the installation state of the dust boot.
*3 Connect an exhaust joint to the air tube and ensure that foreign matter does not enter the tube from joint. *4 When using mounting bracket D (OP-84327), the double amplitude is 0.75 mm 0.03". *5 Contacts are available as options sold separately.

22
Judgment output/analog output type
Main unit GT2-71(C)N GT2-75N GT2-71MCN
NPN output
Expansion unit *1 GT2-72(C)N GT2-76N -
Model
Main unit GT2-71(C)P GT2-75P GT2-71MCP
PNP output
Expansion unit *1 GT2-72(C)P GT2-76P -

Appearance

Mounting type*2 DIN-rail mount Panel mount DIN-rail mount

Number of expansion units *1 Up to 14 expansion units for 1 main unit
Power supply voltage *1 10 to 30 VDC, including 10% ripple (P-P), Class 2 20 to 30 VDC, including 10% ripple (P-P), Class 2
Display range -199.999.9 to 199.999.9
Display resolution 0.1 μm 0.004 Mil
Normal 2200 mW or less (73.3 mA or less at 30 V) 2700 mW or less (90.0 mA or less at 30 V)
Power consumption Power saving (Eco half) 1800 mW or less (60.0 mA or less at 30 V) 2300 mW or less (76.7 mA or less at 30 V)
Power saving (Eco all) 1700 mW or less (56.7 mA or less at 30 V) 2200 mW or less (73.3 mA or less at 30 V)
Response time hsp (3)/5/10/100/500/1000 ms (When using GT2-Pxxx, hsp (12)/20/40/400/2000/4000 ms)
Control output NPN output NPN open collector, 40 V 50 mA or less, residual voltage 1 V or less*1
(HH/HI/GO/LO/LL)*3 PNP output PNP open collector, 30 V 50 mA or less, residual voltage 1 V or less *1
Timing/preset/
Control input No-voltage input
reset/bank input
Output range - 4 to 20 mA with a max. load resistance of 350 Ω
Analog output
Response time - Set response time + 1 ms
Ambient temperature -10 to +50°C 14 to 122°F (No freezing)*1
Environmental resistance Relative humidity 35 to 85% RH (No condensation)
Vibration 10 to 55 Hz Double amplitude 1.5 mm 0.06" in the X, Y, Z axis directions respectively, 2 hours
Main body case/front cover: polycarbonate (PC), Key top: polyacetal (POM),
Materials
Front sheet: polyethylene terephthalate (PET), Cable: polyvinyl chloride (PVC)
GT2-71N(P)/72N(P) Approx. 140 g (including power supply cable)
GT2-75N(P)/76N(P) Approx. 140 g (including panel mount, front protective cover, power supply cable)
Weight
GT2-71MCN(P)/
Approx. 70 g (not including the GT2-CA2M/CA5M/CA10M)
71CN(P)/72CN(P)
*1 When adding expansion units, there are the following restrictions according to the number of connected units.
• When 2 to 8 units are connected including the main unit
• Power supply voltage: 20 to 30 VDC

• Control output current: 20 mA or less

• (GT2-71MCN(P) only) Ambient temperature: -10 to 45°C 14 to 113°F

• When 9 to 15 units are connected including the main unit

• Power supply voltage: 20 to 30 VDC

• Control output current: 10 mA or less (including the DL-RB1A output current)

• Residual voltage: 1.5 V or lower

• (GT2-71MCN(P) only) Ambient temperature: -10 to 45°C 14 to 113°F

*2 When using the DIN-rail mount type, always mount it to a DIN-rail (mounted to a metal plate), and when adding expansion units, always use the end unit (OP-26751).
*3 The GT2-71MCN(P) does not have HH/LL.

Pulse output type

Model GT2-71D

Appearance

Mounting type DIN-rail mount

Number of expansion units Only 1 unit
Power supply voltage 10 to 30 VDC, including 10% ripple (P-P), Class 2
Power consumption 1600 mW or less (53.3 mA or less at 30 V)
Indicators Power supply (green)/alarm (red) indicator, pulse output indicator (green), input indicator
Pulse resolution Select from 0.1/0.5/1/10 μm 0.004/0.02/0.04/0.4 Mil (when shipped: 0.5 μm 0.02 Mil)
Minimum phase difference Select from 0.5/2.5/5/25 μs (when shipped: 2.5 μs)
Control input Origin return No-voltage input (contact, non-contact)
Output signal 90° phase difference, differential square wave (EIA-422 compliant) 4x multiplier
Output signal level +5 V
Ambient temperature -10 to +50°C 14 to 122°F (No freezing)
Environmental
Relative humidity 35 to 85% RH (No condensation)
resistance
Vibration 10 to 55 Hz Double amplitude 1.5 mm 0.06" in the X, Y, Z axis directions respectively, 2 hours
Materials Main body case/front cover: polycarbonate (PC), Cable: polyvinyl chloride (PVC)
Weight Approx. 110 g (including power supply cable)

23
 SP EC I F I C AT I O NS

Large display type

NPN output GT2-100N GT2-E3N
Model
PNP output GT2-100P GT2-E3P

Appearance

Mounting type Panel mount -

2 heads with GT2-100N(P) alone
Number of connectable heads + 3 heads per 1 head board expansion -
When expanded with a maximum of 3 head boards, 11 heads
Power supply voltage 10 to 30 VDC, including 10% ripple (P-P), Class 2 Supplied from the GT2-100N/100P
Display range -199.999.9 to 199.999.9 -
Display resolution 0.1 μm 0.004 Mil -
4500 mW or less 4200 mW or less
Normal
(150.0 mA or less at 30 V) (140.0 mA or less at 30 V)
3700 mW or less 4200 mW or less
Power consumption Power saving (Eco half) *1
(123.3 mA or less at 30 V) (140.0 mA or less at 30 V)
3600 mW or less 4000 mW or less
Power saving (Eco all)*1
(120.0 mA or less at 30 V) (133.3 mA or less at 30 V)
hsp (3)/5/10/100/500/1000 ms
Response time
(When using GT2-Pxxx, hsp (12)/20/40/400/2000/4000 ms)
Control output NPN output NPN open collector, 40 V 50 mA or less*3, residual voltage 1 V or less
(HH/HI/GO/LO/LL) PNP output PNP open collector, 30 V 50 mA or less*3, residual voltage 1 V or less
Timing/preset/
Control input No-voltage input
reset/bank input
Power supply: Terminal block connection
Input/output connector *2 30-pin connector (MIL standard)
Input/output: 20-pin connector (MIL standard)
Ambient temperature -10 to +50°C 14 to 122°F (No freezing)
Environmental resistance Relative humidity 35 to 85% RH (No condensation)
Vibration 10 to 55 Hz Double amplitude 0.15 mm 0.01" in the X, Y, Z axis directions respectively, 2 hours
Main body case/front cover: polycarbonate (PC),
Materials Key top: polyacetal (POM), -
Front sheet: polyethylene terephthalate (PET)
Weight Approx. 380 g Approx. 80 g
*1 When the maximum number of sensor heads is connected, and all devices are set to power saving settings
*2 The connector and cable are sold separately.
*3 When 2 or more sensor heads are connected, 20 mA or less.

Multi-head type NEW

Main unit GT2-500
Model
Expansion unit GT2-550

Appearance

Mounting type *1 DIN-rail mount

Maximum of 3 units including the main unit
Number of expansion units *2
(Maximum of 15 sensor heads)
Power supply voltage 20 to 30 VDC, including 10% ripple (P-P) (GT2-550 power supplied from the main unit), Class 2
4800 mW
Consumption current
160.0 mA or less at 30 V
hsp (3)/5/10/100/500/1000 ms
Response time
(When using GT2-Pxxx, hsp (12)/20/40/400/2000/4000 ms)
Ambient temperature -10 to +50°C 14 to 122°F
Environmental resistance Relative humidity 35 to 85% RH (No condensation)
Vibration 10 to 55 Hz Double amplitude 1.5 mm 0.06" in the X, Y, Z axis directions respectively, 2 hours
Materials Main body case: polycarbonate, Cable: PVC
Weight GT2-500: Approx. 140 g, GT2-550: Approx. 95 g

*1 When connecting the DL Series and expansion units, always connect them when the amplifier unit is connected to the DIN-rail and use the end unit (OP-26751 included with the DL Series).
*2 When using the DL-RB1A (for communication), ensure that the output current is 10 mA or less.

24
 DI MENS I O NS
Unit: mm inch

M8 cable connector
Sensor head (standard) M8 cable connector Sensor head (low stress)
GT2-P12K/ 11.4 12.8
GT2-P12KL/ 11.4 12.8
0.45" 0.5" 44.2
GT2-P12 0.45" 0.5" 44.2 GT2-P12L 1.74"
1.74"
10 0.39" min.
10 0.39" min. (6.8) (0.27")
(6.8) (0.27")
4.6 0.18" 4.6 0.18"
ø3.8 ø0.15" ø3.8 ø0.15"
Cord length Cord length
150 mm 5.91" 150 mm 5.91"
10 0.39" min.
10 0.39" min.
Indicator Indicator

104.8 104.8
4.13" 75.2 2.96" 4.13"
75.2 2.96"
(Mountable (Mountable
range) range)
0
ø8 −0.030
0
ø8 −0.030 0
ø0.31" −0.001"
0
ø0.31" −0.001" 14.10.56"17.9 0.7"
14.1 0.56"17.9 0.7" to to to to
to to to to ø4 26.41.04"30.21.19"
ø4 26.4 1.04"30.2 1.19"
ø0.16"
ø0.16"
3.8 0.15" 3.8 0.15"

Sensor head (flange) M8 cable connector Sensor head - Sensor head cable
GT2-P12KF/ 11.4 12.8
When attached
GT2-P12F 0.45" 0.5" 44.2
1.74"
10 0.39" min.
4.6 0.18"
(6.8) (0.27") ø9.5*
ø0.37"
ø3.8 ø0.15"
Cord length
150 mm 5.91" 67
10 0.39" min. 2.64"
Indicator

ø11
0.43" 90.7
3.57"
ø8
ø0.31" * When using GT2-CHP2M/CHP5M/CHP10M, ø10 ø0.39"
12 0.47" 12 0.47"
−0.005
ø10 −0.030
ø0.39" −0.0002" 6.10.24"14.10.56"
5
Nut −0.0001" 0.2"
M10 x 0.75 14.10.56" 17.9 0.7"
0.03" to to to to
ø4 26.41.04" 30.21.19"
ø0.16"
3.8
0.15"

25
 DIMENS I O NS

Sensor head (Standard)

GT2-H12K/GT2-H12 GT2-H12K/GT2-H12 GT2-H12KF/GT2-H12F
1.10" 1.10" Cable connection Cable connection
GT2-H12KF/GT2-H12F 28
M8 cable connector
0.63"
28 M8 cable connector
0.63" (Straight)
0.42"
10.7 (L-shaped) 0.80"
0.61" 0.61" ø0.37" ø9.5 20.2
(0.49") 16 (0.49") 16 3.05
15.5 15.5 5.9 1.15 ø9.5
(12.5) 5.9 (10.1) (12.5) (10.1) 0.05" ø0.37" 0.12"
ø8 (6.4)(0.25") 0.23" (0.40") ø8 (6.4)(0.25") 0.23" (0.40") 0.05"
ø0.31" 9
ø0.31" 1.15 0.35"

(58) (58)
(2.28") 73.1
2.88" (2.28") 95.3 92.3
66.7 67.8 74.1 3.75" 3.63"
2.63" 2.67" 2.92"

8.7 0.34" 0.04" 1 9.7 0.38"

ø11.6 15.1 ø10 ø0.39" g6 ( -0.005 ) 14
45.3 -0.014 44.3 1.74"
ø0.46" 0.59" -0.0002" 5 0.55"
to ( ) to to
1.63"41.5 32.8 -0.0006" 0.20" 1.59" 40.5 31.8 1.25"
to to 1.78" to to
1.14" 29.0 to M10 x 0.75 0.03" 1.10" 28.0
1.29"
0.24" ø4 ø0.16" 0.24" ø4 ø0.16"
6 (22) 3.8 6.4 (9.6) 6 (22) 3.8 (9.6)
ø8 ø0.31" h5 (+0 6.4
-0.006 ) (0.87") 0.15" 0.25" (0.38") (0.87") 0.15" 0.25" (0.38")
+0
( -0.0002" )

Sensor head (Low stress)

GT2-H12KL/GT2-H12L GT2-H12KL/GT2-H12L GT2-H12KLF/GT2-H12LF Cable connection Cable connection
1.10" 1.10"
GT2-H12KLF/GT2-H12LF 28
M8 cable connector
0.63"
28
M8 cable connector
0.63" (Straight)
0.42"
10.7 (L-shaped) 0.80"
0.61" (0.49") 16 0.61" 16 ø0.37" ø9.5 0.05" ø0.37" 20.2
(0.49") 3.05
15.5 (12.5) 5.9 15.5 (12.5) 1.15 ø9.5
(10.1) 5.9 (10.1) 0.12"
ø8 (6.4)(0.25") 0.23" (0.40") ø8 (6.4)(0.25") 0.23" (0.40") 0.05"
ø0.31" 9
ø0.31" 1.15 0.35"

(58) (58)
(2.28") 73.1 (2.28")
95.3 92.3
66.7 2.88" 67.8 74.1 3.75" 3.63"
2.63" 2.67" 2.92"

8.7 0.34" 0.04" 1 9.7 0.38"

ø11.6 15.1 ø10 g6 ( -0.005 ) 14
45.31.78" -0.014 5 44.3 1.74"
ø0.46" 0.59" ø0.39" -0.0002" 0.55"
to to (-0.0006") to to
0.20" 1.59" 40.5 31.8 1.25"
1.63" 41.5 32.81.29"
to to to to
1.14" 29.0 M10 x 0.75 0.03" 1.10" 28.0

0.24" ø4 ø0.16" 0.24" ø4 ø0.16"

6 (22) 3.8 6.4 (9.6) 6 (22) 3.8 (9.6)
ø8 ø0.31" h5 (+0 6.4
-0.006 ) (0.87") 0.15" 0.25" (0.38") (0.87") 0.15" 0.25" (0.38")
+0
( -0.0002" )

1.48" M8 cable connector

37.6
Sensor head (Standard) 0.99" 0.78"
0.70" 25.1 (12.5) (0.49") 19.7 Cable connection
GT2-H32 17.8 (19.8) (0.78") 8.15 (11.55) (Straight)
ø9.5
ø0.37"
20.35
0.80"
ø8 0.32" (0.45")
ø0.31"
(6.4) (0.25")
3.4
0.13"
(53.3) 97.3
116.4 (2.10") 3.83" 119.5
4.58" 0.38" 90.9 4.70"
9.7 3.58"
0.91" (88.5)
23 (0.56") (3.48")
0.34" 8.7 (14.3) 0.3 0.01"
0.23" 5.9 27.9 1.10" 20 0.79"
17 0.67" 2.4
ø15
ø0.59" 0.09" 43.8 47.6
to to
2-ø4.3 30 77.8 81.6
ø0.17" 1.18" (17.8) 1.72" 1.87"
to to
0.15" (0.70") 3.06" 3.21"
3.8
0.48" ø0.20"
12.2 (25.4) (1.00") ø5
ø12 ø0.47" h6 ( +0
-0.011 )
12.2 (7.8) (0.31")
0.48"
( +0
-0.0004")

1.48" M8 cable connector

37.6
0.78"
Sensor head 0.99"
0.70" 25.1 (12.5) (0.49") 19.7 Cable connection ø9.5 20.35
(Low stress) 17.8 (19.8) (0.78") 8.15 (11.55) (Straight) ø0.37" 0.80"
GT2-H32L ø8
ø0.31"
0.32" (0.45")
(6.4) (0.25")
3.4
0.13"
(53.3) 97.3
(2.10") 3.83" 119.5
116.4 4.70"
4.58" 0.38" 90.9
9.7 3.58"
0.91" (88.5)
23 (0.56") (3.48")
0.34" 8.7 (14.3) 0.3 0.01"
0.23" 5.9 27.9 1.10" 20 0.79"

17 0.67" 2.4
ø15
ø0.59" 0.09" 43.8 47.6
to to
2-ø4.3 77.8 81.6
ø0.17" 30
1.18" (17.8) 1.72" 1.87"
to to
0.15" (0.70") 3.06" 3.21"
3.8
0.48" ø0.20"
12.2 (25.4) (1.00") ø5
ø12 ø0.47" h6 ( +0
-0.011 )
12.2 (7.8) (0.31")
0.48"
(+0
-0.0004")

26
 Unit: mm inch

Sensor head (Standard) 1.48" M8 cable 0.78"

Cable connection
37.6 connector 19.7
GT2-H50 0.99" (Straight) ø0.37" ø9.5 20.35 0.80"
25.1 (12.5) (0.49") 8.15 (11.55)
0.70" 0.32" (0.45")
17.8 (19.8) (0.78")
ø8 ø0.31"
(0.25")
(6.4)
3.4
0.13"

152.4 (53.3)
6.00" (2.10") 115.3
0.38" 137.5
4.54" 5.41"
9.7 108.9
4.29"
0.91"
23 (106.5)
(14.3) (4.19")
0.34" 8.7
0.23" (0.56")
5.9 (0.3) (0.01")
1.81"45.9 20 0.79"

ø15 17 0.67"
2-ø4.3 ø0.59" 2.4
ø0.17" 0.09"
30 48.6 52.4
1.18" (17.8) to to
100.6 104.4
(0.70") 1.91" 2.06"
to to
3.96" 4.11"
0.15"
3.8

12.2 (25.4) ø5
0.48" (1.00") ø0.20"
ø12 ø0.47" h6 +0 ( ) 12.2 (7.8)
-0.011 0.48" (0.31")
+0
(
-0.0004" )
32.5 One-touch air supply joint
Sensor head (Air push) 1.00" 25.5 1.28" (for 4 mm 0.16" outside diameter air tube.)
28 16
GT2-A12K/ 0.42" 10.75
1.10"
ø9.5 ø0.37" (0.40") (10.1)
0.63" Air exhaust joint
(for 2.5 mm 0.10" inside diameter air tube.)
GT2-A12 0.61" 15.5 (12.5) (0.49") 0.23" 5.9
ø14 ø0.55"
0.05" 1.15
0.23" 5.95 M8 connector

17.7
(0.22") 0.70"
97.35
0.04" 1.05 (5.5) 3.83" 13.1 0.52"
95.3
(58) 3.75" 0.49" 12.5
0.06" 1.55
(2.28") 66.7 0.88" 22.4 84.85 15 0.59"
0.99" 25.15 3.34" 18 0.71"
0.12" 3.05 2.63" 39.8
1.57"
0.34" 8.7
ø0.46" ø11.6
29 to 41.5 1.14" to 1.63" 8.75
0.59" 15.1 32.8 to 45.3 1.29" to 1.78" 0.34"
(22) (0.87")
0.24" 6 3.8 0.15" ø0.16" ø4
There are no dust boots on the low
ø8 ø0.31" h5 0.25" 6.4 (9.6) (0.38")
stress type GT2-A12L/A12KL
34.5
1.36"
37.6 1.46" 37
1.48" One-touch air supply joint
0.99" 25.1 (12.5) (0.49") 1.18" 30 (for 4 mm 0.16" outside diameter air tube.)
Sensor head (Air push) 0.70" 17.8 (19.8) (0.78") 0.78" 19.7
(11.55)
GT2-A32 0.80" 20.35 ø9.5 ø0.37" 0.32" 8.15 (0.45") Air exhaust joint ø14 ø0.55"
(for 2.5 mm 0.10" inside
diameter air tube.)

1.17" 29.75 15 0.59"

M8 connector
0.13" 3.4
1.06" 27
155.2
0.49" 12.5 6.11"
(53.3) 142.7
(2.10") (5.5) 5.62" 18 0.71"
119.5 28.1 1.11"
88.5 4.70" (0.22")
0.91" 23 3.48" 32.7 1.29"
(0.56") (14.3) 90.9 75.65
9.7 0.38" 3.58" 2.98" 15 0.59"
0.34" 8.7 18 0.71"
0.09" 0.01" 0.3
0.23" 5.9 27.9 2.4
1.10"
ø0.17"
2 x ø4.3
ø15 44.3 to 77.8 1.74" to 3.06" 5.6
ø0.59" 17 0.22"
1.18" 30 48.1 to 81.6
0.67" 1.89" to 3.21"

(0.70") (17.8) 3.8 0.15" ø0.20" ø5

0.48" 12.2 (25.4) (1.00") 0.48" 12.2 (7.8) (0.31")
ø12 ø0.47" h6 39
1.54"
37.6 1.46" 37
1.48" One-touch air supply joint
Sensor head (Air push) 0.99" 25.1 (12.5) (0.49") 1.18" 30 (for 4 mm 0.16" outside diameter air tube.)
0.70" 17.8 (19.8) (0.78") 0.78" 19.7
GT2-A50 0.80" 20.35 ø9.5 ø0.37" 0.32" 8.15 (11.55) (0.45") ø14 ø0.55"
Air exhaust joint
(for 2.5 mm 0.10" inside 15 0.59"
1.17" 29.75 diameter air tube.)
1.06" 27

M8 connector
0.13" 3.4 178.7
7.04"
0.49" 12.5
(53.3) 191.2
(2.10") (5.5) 7.53" 18 0.71"
137.5 (0.22")
106.5 5.41" 28.1 1.11"
4.19" 108.9 32.7 1.29"
0.91" 23 9.7 0.38" 4.29" 15 0.59"
93.65
(0.56") (14.3) 3.69"
0.34" 8.7 45.89 0.01" 0.3 18 0.71"
0.23" 5.9 1.81" 0.09"
2.4
ø0.17"
2 x ø4.3 ø15 5.6
ø0.59" 49.1 to 100.6 1.93" to 3.96" 0.22"
17
1.18" 30 0.67" 52.9 to 104.4 2.08" to 4.11"

(0.70") (17.8) 3.8 0.15" ø0.20" ø5

0.48" 12.2 (25.4) (1.00") 0.48" 12.2 (7.8) (0.31")
ø12 ø0.47" h6 39
1.54"

27
 DIMENS I O NS
GT2-71N/71P/71MCN/71MCP/71CN/71CP GT2-72N/72P/72CN/72CP
Amplifier unit * *
DIN-rail mount type 24 24
0.94" 14.6 0.57" 0.94" 14.6 0.57"
8.9 8.9
0.35" 0.35"
0.12" 0.12"
3 135° max. 3
(Maximum
when cover
is opened)
36.9 82.9 3.26" 36.9
41.81.45" 1.45"
1.65" 12.4 41.8
1.65" 12.4
0.49" 17.4 0.69" 0.49" 17.4 0.69"

15 0.59" min. 20 21.1 35.41.39" 15 0.59" min. 20 21.1 35.4 1.39"

0.79" 0.83" 0.79" 0.83"
75.8 2.98" 15 0.59" min. 75.8 2.98" 15 0.59" min.
(Maximum when cover
is opened) 132.6 5.22"
* Cable specifications
GT2-71N/71P: ø4.7 ø0.19", 12-core x Brown/Blue: 0.20 mm2, Black/White/Gray/Orange/Green/Pink/Purple/Yellow/Red/Pink purple: 0.15 mm2, Cable length: 2 m 6.6'
GT2-72N/72P: ø4.7 ø0.19", 10-core x Black/White/Gray/Orange/Green/Pink/Purple/Yellow/Red/Pink purple: 0.15 mm2, Cable length: 2 m 6.6'

GT2-71MCN/71MCP/71CN/71CP/72CN/72CP GT2-CA2M/CA10M
Connector Connection cable
(connector type/analog output type amplifier unit)
46 1.81"
44 1.73"
ø15 ø0.59" *
ø0.59" ø15

Cable length: 0.3 m, ø4.7 * Cable specifications

0.98', ø0.19" Outer diameter: ø4.7 mm ø0.19", Cable length: 2 m 6.6' (GT2-CA2M), 10 m 32.8' (GT2-CA10M),

Amplifier unit GT2-71D 12-core x Brown/Blue: 0.20 mm2, Black/White/Gray/Orange/Green/Pink/Purple/Yellow/Red/

Pink purple: 0.15 mm2
Pulse output
*
0.94" 24
14.6 0.57"
8.9 0.35"

0.12"
3 135° max.
(Maximum
when cover
is opened)
82.9 3.26"
36.9 1.45"
41.8
1.65"
0.49"12.4 17.4 0.69" * Cable specifications
20 21.1 Outer diameter: ø4.7 mm ø0.19", Cable length: 2 m 6.6',
15 0.59" min. 35.4 1.39" 9-core x Brown/Blue/Purple/Pink/Orange/Green/Gray/White/Black: 0.15 mm2
0.79" 0.83"
75.8 2.98" 15 0.59" min.
(Maximum when cover
Mounting bracket for is opened) 132.6 5.22"
DIN-rail mount type
amplifier (Optional) End unit (Optional) (2 pcs.) When several units are connected
OP-76877 OP-26751 Number of
units L
L
1 24 0.94"
0.24" 6 2 48 1.89"
6 6 3 72 2.83"
5 15 2-ø3.4 0.24" 0.24" 4 96 3.78"
0.20" 0.59" ø0.13" DIN-rail mount
5 120 4.72"
2-(4.4 x 3.4) (0.17" x 0.13") 6 144 5.67"
(22.6) 20.8
7 168 6.61"
(0.89") 0.82"
22 8 192 7.56"
0.94" 24 0.87" 2.12" 53.8 53.8 9 216 8.50"
9.2 35.4 1.39" 2.12" 10 240 9.45"
15
0.36" 11 264 10.39"
0.59" 53.8 2.12"
Material: SUS304 28.6 1.13" Material: Polycarbonate, Stainless steel 12 288 11.34"
35 0.40" 10.1 10.1 0.40" 13 312 12.28"
1.38" 14 336 13.23"
15 360 14.17"
Amplifier unit GT2-75N/75P/76N/76P
Panel mount type 44.7 1.76" 13.9 0.55"
13.4 0.53"

* Cable specifications (common to all amplifier units)

GT2-75N/75P: ø4.7 ø0.19", 12-core x Brown/Blue: 0.20 mm2, Black/White/Gray/
Orange/Green/Pink/Purple/Yellow/Red/Pink purple: 0.15 mm2,
Cable length: 2 m 6.6'
52 GT2-76N/76P: ø4.7 ø0.19", 10-core x Black/White/Gray/Orange/Green/Pink/
2.05" Purple/Yellow/Red/Pink purple: 0.15 mm2, Cable length: 2 m 6.6'
0.28"
7
1.5 0.06" 0.09" 2.3 0.78"
19.8
0.48"12.2
23.9 20.9 0.82"
0.94"
*
662.60" 0.33"8.5 4.1 0.16"
Panel mounting bracket
(Accessory) Panel cutout Panel mounting bracket
OP-84394 45 1.77" (73) (2.87")
11.9 0.47"
38.8 1.53"
X = 24 x (A-1) + 21
0.94" 0.83" Panel thickness
X When A amplifier units are 1 to 6
0.04" to 0.24"
49 1.93" closely mounted

24 0.94"
69.5 2.74" min.
Protective front cover
21 +0.4
-0
23.8 0.84" +0.02"
-0
0.94" 45 1.77"
69 2.72"
11.7
0.46" Material: (Mounting bracket) Polyacetal,
(Protective front cover) Polycarbonate
28
 Unit: mm inch

Amplifier unit When the supplied mounting bracket is attached GT2-E3N/E3P Expansion board
Large display
GT2-100N/100P
133 5.24"
Panel thickness: 1 to 6
159.5 6.28" 0.04" to 0.24"

82.7
3.26"
79.8 49.3 75.8
3.14" 1.94" 2.98"

0.05" 1.2
0.43" 11
0.48" 12.1 82 3.23"
85.2 3.35" 15.1
1.18"
29.9 0.59"
60 2.36"
1.6
0.06"
1.57" 40 Panel cutout

1.10" 28 97.2
3.83"
Screw hole for mounting OP-84331 (119.6)(139.4)
Nominal diameter: 3 0.12", (4.71")(5.49") 76 2.99" +1 +0.04"
-0 -0
Tapping depth: 5 0.20" max.

139.5 5.49" +1 +0.04"

-0 -0
138.8 5.46"
161.8 6.37" (Outer dimension
of the supplied mounting bracket)

When the optional mounting bracket (OP-84331) is used

84.4
3.32"

4.6 t=1.6 6.6

0.18" 0.06" 0.26"

1.34" 34 4-ø3.5 ø0.14"

1.57" 40 1.57" 40 28 1.10"

4-ø5 ø0.20" 40.5

1.59" 60 2.36"
Nominal diameter: 3 0.12", 5.6 150 5.91"
5.6 0.22" 0.22"
fastened with four tapping 150 5.91" 160 6.30"
screws (supplied)

Amplifier unit Amplifier unit

Multi-head type main unit Multi-head type expansion unit
GT2-500 GT2-550

48 48
1.89" 1.89"
24 25.55 25.55
0.94" 1.01" 1.01"

14.5 56 2.2" (P14 x 4 0.16") 14.5 56 (P14 x 4)

0.57" 0.57" 2.2" 0.16"

15 0.59" min. 15 0.59" min.

71.5 ø3.7 0.15"

2.81" Cable length: 2 m 6.6' 71.5
58.2 53.3 2.81"
2.29" 2.1" 58.2 53.3
2.29" 2.1"
21.5
0.85"

30.3 35.4 30.31.19" 35.41.39"

1.19" 1.39" 15 min.
85 85 3.35"
3.35" 0.59"

When amplifier units are added

0.24" 0.24"
6 6
Number of units L
1 48 1.89"
2 96 3.78"
3 144 5.67"
53.8
2.12" 53.8 2.12"

10.1 10.1 0.4"

0.4"
Connecting
24 communication units
0.94" L

29
 DIMENS I O NS Unit: mm inch

Sensor head
mounting bracket A Sensor head cable (straight)/(oil-resistant straight)
(Optional) 0.47" 12 12 0.47" Mounting hole GT2-CH2M/ 5M/ 10M/20M (Optional)/
OP-76874
R6.5
R0.26" ø0.025 A GT2-CHP2M /5M /10M (Optional)
ø8 ø0.31" ø0.001"
0 027 2000 78.74"(GT2-CH2M/GT2-CHP2M)/5000 196.85"(GT2-CH5M/GT2-CHP5M)/
ø10 ø0.39" ø10 g8 ( +0.005 ) 10000 393.7"(GT2-CH10M/GT2-CHP10M)/20000 787.4"(GT2-CH20M)
ø0.39"
6 16.3
C1.5 0.24" 0.64" ( 00.0002
0011"
) ø9.5* ø0.37"
C0.06" 455°± 1°
7.8
3.5 0.31" A B
0.14"
27.2
0.5 to 1.0* A 5.5 to 11.3* 1.07" 2
0.02" to 0.04" 0.22" to 0.44" 4.8 0.19" 4 x 0.22 mm
7.2 0.28"
Material: SUS304 * Processing accuracy: ±0.05 ±0.002" * When using GT2-CHP2M/CHP5M/CHP10M, ø10 ø0.39"

Sensor head
mounting bracket C
(Optional) 0.47"12 12 0.47" Mounting hole Sensor head cable (L-shaped)
R6.5
OP-84396 R0.26" ø0.025 A GT2-CHL2M /5M /10M/20M (Optional)
ø8 ø0.31" ø0.001"
2000 78.74"(GT2-CHL2M)/5000 196.85"((GT2-CHL5M)/
ø10 ø0.39" ø10 +0.1 10000 393.7"(GT2-CHL10M)/20000 787.4"(GT2-CHL20M)
ø0.39" +0.005
6 16.3 +0.004" 23 ø7ø0.28"
C1.5 0.24" 0.64" +0.0002" 0
0.91" ø9 ø0.35"
C0.06" 455°± 1° B
7.8
5 0.31" 24.2
0.95"
0.20" 4.8 0.19" 4 x 0.22 mm2
0.5 to 1.0* A 5.5 tto 11.3* A
0.02" to 0.04" ø9
0.22" to 0.44"
ø0.35"
Material: SUS304 * Processing accuracy: ±0.05 ±0.002" * Cannot be used with the GT2-H32(L)/H50/A32/A50.

Sensor head Sensor head Pin arrangement

Sensor head cable (straight/L-shaped)
mounting bracket B mounting bracket E 10.5 6.5 A B Casingg cover
0.26"
(Optional) (Optional) 0.41" 2
1 ((1)) ((1)) Brown
R8 4-C2 C0.08" A B
OP-76875 OP-87220 (0.01") 32 1.26" R0.31"
4
3
( )
(2)
( )
(3)
( )
(3)
( )
(4)
White
Blue
(0.2)
12.1 0.48" ø4.2 ( )
(4) ( )
(2) Black
ø0.17"
16.3 11 0.25" 6.3 Dustboot
0.64" 0.43"
R3.8 15 3.5 0.14"
R0.15" 0.59"
Material: SUS304, Zinc

ø8
ø0.31"

Sensor head
mounting bracket D 0.63" 0.63"
16 R0.33"
166
(Optional) R8.5 Mounting hole
OP-84332 OP-87859 (Optional)
OP-84327 ø0.47"
ø12
12
ø0.025 A
Applicable models Applicable models
ø0.001"
ø14 6 0.24" GT2-P12K(F)/P12(F) GT2-P12K(F)/P12(F)
ø0.55" ø14 +0.1
16.3 ø0.55" +0.005 GT2-H12K(F)/H12(F) Materials: Fluorocarbon rubber,
C1.5 0.64" +0.004" 25.3 1"
C0.06" 455°± 1° +0.0002" GT2-A12K/A12 SUS304
5 0.20" 7 0.31"
7.8
5.5 to 11.3* Materials: NBR, SUS304
0.22" to 0.44" ø7.6 * Attached to the sensor head.
1 0.67"
17 0.5 to 1.0* ø0.3"
A
0.02" to 0.04" (Excluding the low stress type)
17 17
0.67" 0.67"
Material: SUS303 * Processing accuracy: ±0.05 ±0.002"
Sensor head
mounting bracket F
(Optional)
0.39" Mounting
OP-87863 OP-84459 OP-84460
0.0 0.7

9.8
hole
3"
x

"
ø0.17
M4

ø4.4 Applicable models Applicable models

8.5 .31" 8.5 GT2-H32 GT2-H50
23.4 0.33" ø8 ø0 0.33" 58.2 81
ø8 +0.2 2.29" GT2-A32 3.19" GT2-A50
0.92" 11.1 + 00
0.00
0.44"
ø0.3 05
* Attached to the sensor head. * Attached to the sensor head.
1" + .01"
0 .000
13.9 12 2" ø11.6 ø0.46"
0.55" 0.47" 6 øø11.6 ø0.46"
0.24" * Thickness: Over 5 mm 0.20"
M4 x
0.7 0

Material: SUS303
.03"

Contact
Fluorocarbon resin
Standard 5 0.20"
Super-tough Flat plate (Optional) Roller (Optional) (Optional)
0.02" ø0.35" 0.02"
OP-77678 M2.5 x 0.45 OP-77682 5 0.20" 0.02"
M2.5 x 0.45
OP-77679 5 0.20" 0.02" OP-77680 ø9 M2.5 x 0.45 OP-80228 0.20"
5 0.02"
M2.5 x 0.45 ø0.30" ø7.5 M2.5 x 0.45
0.14"
SR1.5 0.06" 3.5
5
3.8 3.8 SR1.5 0.06" 0.37" 9.5
0.35" 9
0.15" ø5 ø0.20" 0.15" ø5 ø0.20"
ø6 ø0.24"
4.5 0.30" 7.5 SR1.5 0.06"
0.18" ø7 ø0.28" ø5 ø0.20"
øø9
Material: SUS304 ø0.35"
Standard Standard Material: SUS304 4.5 0.18"
Material: SUS304 Material: SUS304 SUS440C
equipment equipment Super-tough
of the general- SUS440C of the high-accuracy Super-tough tungsten alloy Material: Fluorocarbon resin (PTFE)
purpose sensor head type sensor head tungsten alloy
4.4 4 9
GT2-P12(L/F) GT2-P12K(L/F) 0.17" 0.16" 0.35"
GT2-H(A)12(L/F/LF) GT2-H(A)12K(L/F/LF)
GT2-H(A)32(L)/GT2-H(A)50

Ceramic Needle Offset Spacer Roller (high-accuracy)

(Optional) 0.20" (Optional) 0.20" (Optional) ø7.5 ø0.30" (Optional) (Optional)
ø6 ø0.31"
OP-81970 5 0.02"
M2.5 x 0.45 OP-77681 5 0.02"
M2.5 x 0.45 OP-77683 ø0.24" 0.02" OP-77684
M2.5 x 0.45
0.02"
M2.5 x 0.45
OP-93332 ø8
0.13"
0.02"
5.5 3.2 M2.5 x 0.45
8
6.2 0.31" 0.22" 100
0.24" 0.08" 0.39"
5 0.20" 12.2 2
3.8 SR1.5 0.06" 3.5 0.48" 21.7
0.15" ø5 ø0.20" 0.14" M2.5 x 0.45 0.02" 0.85"
21 111.7
0.83" 20 Effective screw depth: 0.46"
0.79" 3.6 6.5 mm 0.26"
0.14" ø9
Material: SUS304, Ceramic Material: SUS304 Material: SUS304 Material: SUS304 ø4 ø0.16" Material: SUS304 0.16" ø0.35"
Super-tough C0.2 C0.008" Super-tough 0.03" SR0.8 10 0.39" SUS303
ø1.2 ø0.05" SUS440C 4.5 4
tungsten alloy tungsten alloy ø1.6 ø0.06"
ø4 ø0.16" 0.18" ø9
ø0.35"

30
 I NPU T /O U T PUT CI R CU I T D I A G R A M S

I/O circuit GT2-71N/72N/71CN/72CN/71MCN/75N/76N External input circuit

Brown *1 5 VDC Pink: Preset input

10 to 30 VDC *3
Purple: Bank A input
Orange (HH output) *2
Overcurrent protection circuit
Load 5 to 40 VDC Pink/purple: Timing input
Black (HI output) Yellow: Bank B input
Load 5 to 40 VDC
Red: Reset input
Main circuit

Gray (GO output)

Load 5 to 40 VDC

Main circuit
White (LO output)
Load 5 to 40 VDC
Green (LL output) *2 Blue *1
Load 5 to 40 VDC
Blue *1
0V
(Short-circuit current: 1 mA max.)
Pink, purple, pink/purple, yellow, red *4
Input circuit External input

I/O circuit GT2-71P/72P/71CP/72CP/71MCP/75P/76P External input circuit

10 to 30 VDC
Brown *1 3
10 to 30 VDC * Brown *1
Orange (HH output) *2
Overcurrent protection circuit

Load

Main circuit
Black (HI output)
Gray (GO output) Load
Main circuit

White (LO output) Load Pink: Preset input

Purple: Bank A input
Green (LL output) *2 Load
Pink/purple: Timing input
Blue *1 Load
0V Yellow: Bank B input
(Short-circuit current: 2 mA max.)
Pink, purple, pink/purple, yellow, red *4 Red: Reset input
Input circuit External input

*1 Brown and blue are applicable only to main units (GT2-71N/71P/71CN/71CP/71MCN/71MCP/75N/75P). Not applicable to expansion units (GT2-72N/72P/72CN/72CP/76N/76P).
The connector type expansion unit (GT2-72CN/72CP) is not connected to the internal circuit.
*2 The orange and green wires are used as analog output cables for the analog type amplifier unit (GT2-71MCN/71MCP).
For details, refer to the analog output circuit diagram.
*3 20 to 30 VDC when expansion unit is connected or for the analog type amplifier unit (GT2-71MCN/71MCP).
*4 For details on external input, refer to the external input circuit diagram.

Analog output circuit Pulse output amplifier unit GT2-71D

GT2-71MCN/71MCP I/O circuit External input circuit Recommended input device

Brown 5 VDC AM26LS32 line receiver or equivalent device

10 to 30 VDC
5 VDC
Orange Black, white,
Analog output 33 Ω orange
(4 to 20 mA) Black: Phase A, White: Phase Pink 390 Ω
Main circuit

Main circuit

B, Orange: Phase Z
Main circuit

Purple, gray,
33 Ω green Purple: Reversed phase A
Gray: Reversed phase B
Green: Reversed phase Z Blue
Green *
0 V (for analog) Blue
0V
Pink * (Short-circuit current: 1 mA max.)
Input circuit Input

* The green and blue wires are common internally. * For details of the external input, refer to the diagram of the external input circuit.

Output circuit of the large display amplifier unit Input circuit of the large display amplifier unit Multi-head amplifier unit GT2-500 (main unit)
GT2-100N/GT2-E3N GT2-100N/GT2-E3N The power supply cable is as follows.
(Pin Nos. 1 to 5, 11 to 15, 21 to 25) (Pin Nos. 6 to 10, 16 to 20, 26 to 30)
+* 5 VDC Brown
20 to 30 VDC
20 to 30 VDC
Overcurrent protection circuit

1 to 5, 11 to 15, 21 to 25
Sensor main circuit

Blue
Load 5 to 40 VDC 6 to 10, 16 to 20, 26 to 30
Main circuit

-*
-*
0V
(Short-circuit current: 1 mA max.)
* The +/- terminals are provided in the GT2-100N only. * The - terminal is provided in the GT2-100N only.
They are not provided in the GT2-E3N. It is not provided in the GT2-E3N.

Output circuit of the large display amplifier unit Input circuit of the large display amplifier unit
GT2-100P/GT2-E3P GT2-100P/GT2-E3P
(Pin Nos. 1 to 5, 11 to 15, 21 to 25) (Pin Nos. 6 to 10, 16 to 20, 26 to 30)
+* 20 to 30 VDC
20 to 30 VDC
+*
Overcurrent protection circuit
Sensor main circuit

Main circuit

1 to 5, 11 to 15, 21 to 25
6 to 10, 16 to 20, 26 to 30
Load
-*
0V (Short-circuit current: 2 mA max.)

* The +/- terminals are provided in the GT2-100P only. * The + terminal is provided in the GT2-100P only.
They are not provided in the GT2-E3P. It is not provided in the GT2-E3P.

31
Copyright (c) 2014 KEYENCE CORPORATION. All rights reserved. GT2pen-KA-C2-US 1034-2 611828 Printed in Japan
* 6 1 1 8 2 8 *