Scribd
Upload
32 views

Suporflow Filter: Description Specifications

Uploaded by

sopranomohammad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
32 views

Suporflow Filter: Description Specifications

Uploaded by

sopranomohammad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Chemical Filtration Filters Element Data Sheet E62c

SuporFlow® Filter

Description Specifications
The SuporFlow filter is designed Materials Operating Conditions
specifically for the filtration of • Medium: Polyethersulfone (PES) • Maximum temperature:
ultra-high-purity chemicals up to • Core, cage, and end caps: High 70°C / 158°F
70°C / 158°F.1 It combines the density polyethylene (HDPE) • Maximum forward / reverse
latest advances in polyethersulfone • Support and drainage: High density differential pressure:
membranes with Pall’s Ultipleat® filter polyethylene (HDPE) 0.103 MPa @ 70°C / 15 psid @ 158°F
technology. • O-ring options: Viton2 and Teflon2
Integrity Test Values4
encapsulated Viton
• True hydrophilic polyethersulfone • 0.1 µm, 10 in segment,
membrane Removal Rating 0.14 MPa (20 psig), < 40 cm3 / min
• High retention characteristics • Monorated3 @ 0.1 µm
Recommended Applications
• Excellent compatibility
Filter Areas • Aqueous based chemicals
• High flow rates
• 254 mm / 10 in: 1.86 m2 / 20 ft2 • Bulk chemical distribution systems
• Low extractables
• Point-of-use applications
• Instant wettability Configurations 1 Not compatible with SC1 and SC2 above 35˚C.
• 100% integrity tested and testable • Nominal length: 254 mm / 10 in 2 Teflon and Viton are registered trademarks of
• Manufactured in a cleanroom • Diameter: 70 mm / 2.75 in E. I. du Pont de Nemours and Company.
3 Monoratings are based upon monodisperse
environment • Code 3: 222 double O-ring / flat end polystyrene latex bead challenges in 18.2
Megohm-cm ultrapure DI water.
• Code 8: 222 double O-ring / finned 4 Test fluid used is 60:40, IPA: H 2 O.
end
Pressure Drop vs. Liquid Flow Rate5

Flow rate (gpm)


0 1 2 3 4 5 6 7 8 9 10
0.05

6
Differential pressure (MPa)

0.04

Differential pressure (psid)


0.03
0.1 µm (UET) 4
0.02
2
0.01

0 0
0 5 10 15 20 25 30 35 40

Flow rate (L/min)

5 For liquids with a viscosity differing from water, multiply


the pressure drop by the viscosity in centipoise.

Part Numbers / Ordering Information

Part Removal Nominal Length Configuration O-Ring Material7


Number6 Rating (µm) (mm / in) Code

ABD1UET3EH1 0.1 254 / 10 3 Teflon encapsulated Viton


ABD1UET8EH1 0.1 254 / 10 8 Teflon encapsulated Viton
MRD1UET3EH1 0.1 254 / 10 3 Teflon encapsulated Viton
6 The above filter configurations are also available in 508 mm / 20 in, 762 mm / 30 in,
and 1016 mm / 40 in lengths. These can be ordered by changing the fourth digit
in the part number to a 2, 3, or 4 respectively.
7 Other O-ring materials are available.

Unit conversion: 1 MPa = 10 bar

25 Harbor Park Drive Visit us on the Web at www.pall.com/micro


Port Washington, New York 11050 Pall Corporation has offices and plants throughout the world.

1.800.360.7255 toll free (only in US)


1.516.484.3600 phone
1.516.625.3610 fax
© Copyright 2007, Pall Corporation. Pall, , SuporFlow and Ultipleat are trademarks of Pall Corporation.
[email protected] ® Indicates a Pall trademark registered in the USA. is a service mark of Pall
Corporation.

E62c 12/07

You might also like