THROTTLE VALVES FOR RELAYS AND RADIATORS

Series 2013

 General Features
 Characteristics
The butterfly valves, metal to metal sealing with thin blade(or full tightening type, with o-ring blade), are
used on power transformer with the scope to allow the disconnection of a component of the circuit (ie
buchholz relay or radiator) without having to lower the oil below the level of the component itself.
This kind of valve are preferred to the conventional gate valves for their compact overall dimension in the
direction of the oil flow.
 Field of Use
The butterfly valves (standard execution) may be used with the following characteristic values:
• Fluid: mineral oil or silicon fluid
• operating pressure in open position max 10 bar
• operating pressure in close position max 8 bar
• operating conditions (depending from material of gasket) see par 4

 Construction Features, Finish and Accessories

 Construction Features
Butterfly valves are constructed as follows (please refer to drawings):
• Body in forged mild steel or cut from steel sheet
• Spindle made in steel
• Drive and gland made in brass
• Open/close position indicated by an aluminium plate.
• S/steel screws
• Throttle made in carbon steel (thin blade) or made in brass (o-ring blade)
• O/Rings made in oil resistant rubber
 Finish
Body of the wafer type is zinc plated first and after is protected by one coat of epoxy primer and one coat
of polyurethane paint (total thickness 80 µm), final colour RAL 7030; in all types screws and pins are in
stainless steel; brass parts and aluminium parts are self colour.
In any case the device is suitable for outdoor installation in tropical climate and with normal industrial
pollution.
Body of the welding neck type is self colour without any coating or painting
 Accessories
The valve is supplied with one (or two) O/Ring flange gasket
 Special executions
Special execution are available for very low temperatures or very corrosive ambient. Please contact our
technical department.

File : 24-BUTTERFLY VALVES.doc rev. 06dtd 22/03/2011 UNCONTROLLED COPY Page 1 di 4

 Operating features
 Tightness of spindle
The tightness to oil leakage from the spindle on the butterfly valve, is guaranteed by a set of o/rings on
the spindle and on the gland obtaining an excellent tightness and at the same time allowing an easy
replacement of the gasket
No leakage is tolerated from the spindle in any case.
 Tightness of butterfly
 Metal to metal sealing (thin blade throttle)
The oil tightness of the butterfly is obtained by contact metal to metal, thus assuring a constant
performance even after a long use .
Leakage at the butterfly is checked during assembly, testing with oil at 20° C, 1 bar and viscosity of
30,5 cSt.
Following values of max admitted leakage:

Nominal diameter of valve in mm ≤ 100 100 < > 175 ≥ 175

Admitted leakage in dm3/h measured in 1 hour ≤ 0,5 ≤ 1,0 ≤ 2,0

 Full tightening sealing (TW80 with o-ring blade)

The oil tightness of the butterfly is obtained by contact of an o/ring (mounted on the throttle) and the
metal body, thus assuring full sealing between throttle and body.
No leakage is present between throttle and body in closed position.
 Operating Torque
The operating torque measured by dynamometric spanner are the following :

Nominal diameter of valve in mm ≤ 100 100 < > 150 ≥ 150

Operating torque in Nm. ≤ 10 ≤ 30 ≤ 30
Closing torque in Nm. ≤ 70 ≤ 100 ≤ 150
Opening torque in Nm. ≤ 40 ≤ 50 ≤ 50

Operating torque: Torque necessary to turn the shaft from the open to the closed position;
Closing torque: Torque necessary to obtain the complete closure of the valve;
Opening torque: Torque necessary to open the valve, after complete closure.

File : 24-BUTTERFLY VALVES.doc rev. 06dtd 22/03/2011 UNCONTROLLED COPY Page 2 di 4

 Admitted operating conditions
 Standard execution (N) – Nitrile rubber gaskets
• Ambient conditions:
 Ambient temperature: -20°C to +50°C
 Relative humidity: 95% to 20°C - 80% to 40°C - 50% to 50°C
• Insulating liquid and it's temperature:
 Mineral oil: -20°C to +110°C
 Silicone oil: -20°C to +110°C
 Execution H – H-NBR rubber gaskets
• Ambient conditions:
 Ambient temperature: -40°C to +50°C
 Relative humidity: 95% to 20°C - 80% to 40°C - 50% to 50°C
• Insulating liquid and it's temperature:
 Mineral oil: -40°C to +140°C
 Silicone oil: not admitted
 Execution V – Fluor-rubber gaskets (Viton V)
• Ambient conditions:
 Ambient temperature: -15°C to +50°C
 Relative humidity: 95% to 20°C - 80% to 40°C - 50% to 50°C
• Insulating liquid and it's temperature:
 Mineral oil: -15°C to +160°C
 Silicone oil: -15°C to +160°C

 Mounting, Adjustment and Maintenance

 Mounting
The throttle valve has to be mounted as shown on reference drawings or at page 5.86
Valve has to be mounted using screws or rods, washers and nuts and putting the o/ring on the
groove for flange tightening
 Operating instructions
The design of the operating system is common to all valves; to open and close the valve operate as
follows (please refer to drawings):
• The visible symbol or inscription on plate (10) indicates the valve position;
• To close the valve first remove the seal or padlock (if present),
• With the appropriate spanner turn the drive (2) clockwise 90° to close the valve; counter clockwise
90°
to open the valve
• The visible part of plate (10) indicates the actual valve position;

 Maintenance
The Throttle valves do not need periodic maintenance; however it is advisable to check regularly the
external tightening of valve

File : 24-BUTTERFLY VALVES.doc rev. 06dtd 22/03/2011 UNCONTROLLED COPY Page 3 di 4

 Range of types and reference drawings
The butterfly valves have standard execution flanges according to UNI PN10 and PN6; flanges according
to other standards can be supplied as special execution.
Nominal diameters (DN) are 25;50;80;100;125;150;200;250;300
Below detailed list of available types
 Series SW for radiators– metal to metal sealing (square flange – thin blade)
• Nominal diameter: 80 mm
• Execution
- A1 & A0 Welding neck
- B1 & B0 Wafer type for mounting between two flanges
• Reference drawing : page 5.82 & page 5.83
• Mounting sketch
- A1 & A0 Welding neck : page 5.86 fig. A or B
- B1 & B0 Wafer type for mounting between two flanges : page 5.86 fig. C or D
• Note: A1 & B1 flanges with groove for O/R 6400 (supplied with the valve)
A0 & B0 flat flanges for flat gasket (supplied on demand)
 Series TW for radiators – full tightening valve (square flange – o/ring blade)
• Nominal diameter: 80 mm
- Execution wafer type for mounting between two flanges
• Reference drawing : page 5.81
- Mounting sketch: page 5.86 fig. C or D
 Series DN – round flange
• Nominal diameter: 25; 50; 80 mm
• Execution wafer type for mounting between two flanges
- PN6 flange size : bolt circle diameter acc to UNI2276-67
- PN10 flange size : bolt circle diameter acc to UNI2277-67
• Reference drawing : page 5.84
• Note : this kind of valves are delivered with HNBR gaskets for flange tightening
 Series JU – large round flange
• Nominal diameter: 100;125;150;200;250;300 mm
• Execution wafer type for mounting between two flanges
- PN10 flange size : bolt circle diameter acc to UNI2277-67
• Reference drawing : page 5.85

 Order Specifications
When ordering it is necessary to indicate
• Series (type)
• Size
• Operating conditions (if not indicated, we will consider standard N)
• Special requirements

Example :
To order nr. 1 Throttle valve type DN50 PN6 standard execution please indicate the following:
Nr 1 Throttle valve DN50 PN6

File : 24-BUTTERFLY VALVES.doc rev. 06dtd 22/03/2011 UNCONTROLLED COPY Page 4 di 4