Scribd
Upload
20 views

Displacement Method

Uploaded by

sundar.lal1
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
20 views

Displacement Method

Uploaded by

sundar.lal1
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 47

CIVIL

ENGINEERING
Structure analysis
DISPLACEMENT METHOD
DPP-1
(Discussion Notes)

Aishwary Sir
#Q.1 A uniform rise in temperature on a total frame will cause-

A No sway

B Sway depending upon temperature

C Sway depending upon relative property of the member & temperature

D None of these
#Q.2 Consider the following frame :

The Bending Moment at joint D is ________ kNm.


#Q.3 For the beam shown below, what are the distribution factors at joint B?

A 0.5,0.5

B 0.4, 0.6

C 0.67, 0.33

D 0.33, 0.67
#Q.4 The carry over Cab for the beam as shown in figure is

A 1/3

B 2/3

C 2/3

D 2
#Q.5 Consider the beam shown below:

The value of moment MBC is :


A 30.94 kNm (clockwise)

B 27.64 kNm (Anticlockwise)

C 30.94 kNm (Anticlockwise)

D 27.64 kNm (clockwise)


#Q.6 The frame below shows three beam elements OA, OB and OC with identical
length L and flexural rigidity EI, subjected to an external moment M
applied at the rigid joint O. The correct set of bending moments [MOA, MOB,
MOC] that develop at O in the three beam elements OA, OR and OC
respectively, is
EI/L is constant for all there member

A 3M/8, M/8,4M/8

B 13M/11,4M/11,4M/11

C M/3, M/3, M/3

D 3M/7, 0,4M/7
#Q.7 For the frame as shown, the value of P for which the rotation at B is
15
observed to be anticlockwise?
𝐸𝐼

A 7.5 kN

B 10 kN

C 15 kN

D 20 kN
#Q.8 In the frame shown above the magnitude of axial force in member PQ is :

A 30 kN

B 15 kN

C 7.5 kN

D 10 kN
#Q.9 A uniform simply supported beam is subjected to a clockwise moment M
at the left end. What is the moment required at the right end so that
rotation of the right end is zero?

A 2M

B M

C M/2

D M/3
#Q.10 The following steps are involved in determining the reaction ‘R’ of the
beam shown in the figure using moment distribution method:

1. Writing down the equation for BM at B and equating Mba.


2. Determining FEM at A and carrying one half of its negative value
to the end B.
3. Adding the value obtained in 2 to FEM at B to get Mba-
The correct sequence of these steps is
A 2,3, 1 not being relevant

B 1,2,3

C 2,3,1

D 1,2,3 not being relevant


#Q.11 If joint A and D are fixed Support then the Final End Moment at Fixed A is

A 1.59 kNm

B 2.88 kNm

C 2.72 kNm

D 5.78 kNm
#Q.12 The Moment at Fixed Support D is_______kNm
#Q.13 Determine the reactions at the supports. Assume A is fixed and B and C are
rollers that can either push or pull on the beam. El is constant.
#Q.14 Determine the internal moments at each support of the beam shown in
Fig. El is constant.
ANSWER KEY
1. (A)
2. (500)
3. (C)
4. (D)
5. (A)
6. (D)
7. (C)
8. (C)
9. (C)
10. (C)
11. (A)
12. (2 kN-m)
13. (33kN, 33kN, 6kN)
14. 62.63, 125.26,-125.26, 281.58, -281.58, 234.21
Thank You
GW Soldiers

You might also like