VT-275 Codes
Uploaded by
ScribdTranslationsVT-275 Codes
Uploaded by
ScribdTranslationsDIAGNOSTIC FAULT CODES
Consult service literature for the latest information before attempting any repairs.
CODE
NUMBER CIRCUIT CONDITION DESCRIPTION
NAME
111 '%/ 0Q UG FGVGEVCP GTTQTGU Ō UÎNQ EÎFKIQ FG FGUVGNNQ
112 NDE PWR Electrical system voltage B+, high out of range
113 NDE PWR Electrical system voltage B+, low out of range
114* ECT Engine coolant temperature signal low out of range
115* ECT Engine coolant temperature signal high out of range
121* map Manifold absolute pressure signal, high out of range
122* map Manifold absolute pressure signal, low out of range
123* map Manifold absolute pressure signal, in fault range
124* PCI Injection control pressure signal low out of range
125* PCI Injection control pressure signal, high out of range
131* APS/IVS APS signal, low out of range
132* APS/IVS APS signal, high out of range
133* APS/IVS APS signal, in range with fault
134* APS/IVS APS and IVS signal do not match
135* APS/IVS Idle validation switch circuit failure
143 CMP Incorrect CMP signal signature
145 CMP CMP signal inactive
146 CKP CKP signal inactive
147 CKP Incorrect CKP signal signature
148* MAF Mass air flow signal frequency high out of range
149* MAF Mass air flow signal frequency high out of range
152* BAP Barometric absolute pressure signal, low out of range
154* IAT Intake air temperature signal low out of range
155* IAT Intake air temperature signal, high out of range
161* MAT Manifold air temperature signal low out of range
162* MAT Manifold air temperature signal high out of range
163* EGR
Exhaust gas recirculation valve position signal, low out of range
221 SCCS Cruise control-PTO switch circuit failure
222 BRAKE Brake switch circuit failure
225 EOP EOP sensor signal, in faulty range
231 ATA ATA data communication link error
237 FPC OCC Fuel Pump Control Failed Self Test
238 IAH Intake Air Heater Control OCC Failed Self Test
241 IPR OCC injection pressure regulator failed self-test
251 CPG Failed OCC self-test glow plug control
268 ACC A/C Clutch Control Relay OCC Failed Self Test
311* EOT Engine oil temperature signal low out of range
312* EOT Engine oil temperature signal high out of range
313** EOPS Engine oil pressure below warning level
315* EWPS Engine speed above warning level
* +PFKEC NC N¶ORCTC ¶ODCT ő'0)+0'Œ (/OTOR) on when the DTC is set
** +PFKEC NC N¶ORCTC TQLC ő'0)+0'Œ (/1614) GPEGPFKFC EWCPFQ GUt· engine warning protection system enabled and a DTC is set
100 /QVQT 86275 +PVGTPC VKQPCNs
DIAGNOSTIC FAULT CODES
CODE
NUMBER CIRCUIT NAME DESCRIPTION OF THE CONDITION
316 EWPS
Engine coolant temperature unable to reach commanded set point
321* EWPS Engine coolant temperature above warning level
322** EWPS Engine coolant temperature above critical level
324** IST Idle cut-off timer enabled to turn off the engine
325 EWPS Reduced power, coupled with cooling system performance
331* PCI Injection control pressure above system working range
332* PCI Injection control pressure above specification with engine not running
333* ICP sys Injection control pressure above/below desired level
334 ICP sys ICP unable to reach fixation point in time (poor performance)
335 ICP sys ICP unable to build up pressure during engine rotation
346 A.M.S. Failures were detected during the EGR portion of the AMS test
365* EGR EGR valve position above/below desired level
368* EGR EGR driver module / ECM2 communication failure
373 IAH Intake air heater relay circuit failure
374 FPC Fuel pump relay circuit failure
375 CPG Glow plug relay circuit failure
421-426 INJ Opening from low side to high side (cylinder number indicated)
431-436 INJ High side shorted to low side (cylinder number indicated
451-456 INJ High side shorted to ground or VBAT (cylinder number indicated)
523 IDM IDM VIGN Low Voltage
525* IDM IDM failure
533 IDM IDM Relay High Voltage
534 IDM IDM Relay Low Voltage
543* ECM/IDM ECM/IDM communication failure
551 ECM/IDM IDM/CMPO idle signal
552 ECM/IDM Incorrect IDM CKPO signal signature
553 ECM/IDM IDM / CKPO idle signal
554 ECM/IDM Incorrect IDM CKPO signal signature
613* '%/ '%/ / +&/ őUQHVYCTGŒ PQ EQORCVKDNG
614* NDE EFRC/ECM configuration mismatch
621* NDE Engine is using default manufacturing range
622* NDE Motor is using default field range
623* NDE Invalid Engine Family Range Code (EFRC)
624 NDE Default field active
626 NDE PWR Unexpected resume failure
631 NDE Read-only memory (ROM) self-test failure
632 '%/ /GOQTKC FG CEEGUQ CNGCVQTKQ ( 4#/) Ō HCNNC FG NC CWVQRTWGDC FGN %27
655 NDE Incompatible level of programmable parameter list level
661 NDE RAM programmable parameter list corruption
664 NDE Incompatible level calibration
665 NDE Corruption of memory contents of programmable parameters
/QVQT 86275 +PVGTPCVKQPCNs 101
+PFKEC NC N¶ORCTC ¶ODCT ő'0)+0'Œ (/OTOR) on when the DTC is set
** +PFKEC NC N¶ORCTC TQLC ő'0)+0'Œ (/1614) GPEGPFKFC EWCPFQ GUt· engine warning protection system enabled and a DTC is set
