Microprocessor Reset Circuits

Data Sheet ADM1810 to ADM1813/ADM1815 to ADM1818

FEATURES FUNCTIONAL BLOCK DIAGRAMS
Reliable low cost voltage monitor with reset output ADM1810/ADM1815
VCC
Suitable for monitoring 2.5 V, 3 V, 3.3 V, and 5 V power
supply voltages RST
Reset threshold levels: 4.62 V, 4.35 V, 3.06 V, 2.88 V, 2.55 V, VCC
TOLERANCE
2.31 V, and 2.18 V typical BIAS
Active high and low push-pull output choices: ADM1810, 150ms
DELAY
ADM1812, ADM1815, and ADM1817 GND TC
REFERENCE
Open-drain with internal pull-up resistor output choices:
ADM1811, ADM1813, ADM1816, and ADM1818
Can be used with a manual push-button to generate a reset:
ADM1811/ADM1816
ADM1813, ADM1818 VCC
Initialization of microprocessor systems with added safety 5.5kΩ
RST
Available in 3-lead SOT-23 and SC70 packages
VCC
APPLICATIONS TOLERANCE
BIAS
150ms
Microprocessor systems DELAY

Computers GND TC
REFERENCE
Controllers
Intelligent instruments
Automotive systems
ADM1812/ADM1817
VCC
GENERAL DESCRIPTION
The ADM181x range of voltage monitoring circuits is used in RST
VCC
any application where an electronic system needs to be reset TOLERANCE
when a voltage increases above or below a predetermined value. BIAS
150ms
DELAY
Because of the reset delay time incorporated into the ADM181x GND TC
series, these devices provide a safe startup for electronic systems. REFERENCE

Before a system initializes, the power supply must stabilize.

Using the ADM181x series ensures that there are typically 150 ms
for the power supply to stabilize before the system resets and ADM1813/ADM1818
VCC
safe system initialization begins. RESET
5.5kΩ
RST
MONITOR
The ADM181x series of microprocessor reset circuits are
VCC
available in low cost, space-saving SOT-23 and SC70 packages. TOLERANCE
BIAS
150ms
DELAY

GND TC
00064-001

REFERENCE

Figure 1.

Rev. F Document Feedback

Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Tel: 781.329.4700 ©1999–2013 Analog Devices, Inc. All rights reserved.
Trademarks and registered trademarks are the property of their respective owners. Technical Support www.analog.com
ADM1810 to ADM1813/ADM1815 to ADM1818 Data Sheet

TABLE OF CONTENTS
Features .............................................................................................. 1 Typical Performance Characteristics ..............................................6
Applications ....................................................................................... 1 Theory of Operation .........................................................................7
General Description ......................................................................... 1 Timing Diagrams for All Devices ...............................................7
Functional Block Diagrams ............................................................. 1 ADM1813 and ADM1818 .............................................................7
Revision History ............................................................................... 2 ADM1810, ADM1812, ADM1815, and ADM1817 ....................7
Specifications..................................................................................... 3 ADM1811 and ADM1816 .............................................................7
Absolute Maximum Ratings............................................................ 4 Outline Dimensions ..........................................................................8
ESD Caution .................................................................................. 4 Ordering Guide .............................................................................9
Pin Configurations and Function Descriptions ........................... 5

REVISION HISTORY
10/13—Rev. E to Rev. F 2/03—Rev. A to Rev. B.
Changed Open-Drain to Open-Drain with Internal Pull-Up Edits to Features.................................................................................1
Resistor ............................................................................ Throughout Deleted Table I ...................................................................................1
Updated Outline Dimensions ......................................................... 8 Edits to Specifications .......................................................................2
Changes to Ordering Guide ............................................................ 9 Edits to Absolute Maximum Ratings ..............................................3
Edits to Ordering Guide ...................................................................3
8/08—Rev. D to Rev. E Added Typical Performance Characteristics .................................4
Changes to Table 3 ............................................................................ 5 Edits to ADM1813 AND ADM1818 section .................................5
Updated Outline Dimensions ......................................................... 8 Edits to ADM1810, ADM1812, ADM1815, and
Changes to Ordering Guide ............................................................ 9 ADM1817 Section .............................................................................5
Edits to ADM1811 and ADM1816 Section ...................................5
10/05—Rev. C to Rev. D Updated Outline Dimensions ..........................................................6
Updated Format .................................................................. Universal
Added Figure 3 .................................................................................. 5 3/02—Rev. 0 to Rev. A.
Changes to Table 3 ............................................................................ 5 Addition of Table ..............................................................................1
Updated Outline Dimensions ......................................................... 8 Edits to Ordering Guide ...................................................................3
Edits to Ordering Guide .................................................................. 9 Addition of New Text to ADM1813 and ADM1818 Section ......4

9/03—Rev. B to Rev. C. 4/99—Revision 0: Initial Version

Added SC70 ......................................................................... Universal
Edits to Specifications ...................................................................... 2
Edits to Ordering Guide .................................................................. 4
Updated Outline Dimensions ......................................................... 7

Rev. F | Page 2 of 12
Data Sheet ADM1810 to ADM1813/ADM1815 to ADM1818

SPECIFICATIONS
VCC = full operating range, TA = −40°C to +105°C, unless otherwise noted.

Table 1.
Parameter Min Typ Max Unit Comments
SUPPLY
Voltage 1 5.5 V TA = 0°C to 105°C
1.2 5.5 V TA = −40°C to +105°C
Current 9 16 µA VCC = 5.5 V, VCC > VTH, no load
4 10 µA VCC = 3.6 V, VCC > VTH, no load
OUTPUT CURRENT
RST Output Source Current 350 µA VCC ≥ VTH (max), reset not asserted (ADM1810/ADM1815)
RST Output Source Current 350 µA VCC ≤ VTH (min), reset asserted (ADM1812/ADM1817)
RST Output Sink Current 8 mA VCC ≥ 2.7 V, reset asserted, VOUT = 0.4 V (ADM1810/ADM1811/
ADM1813/ADM1815/ADM1816/ADM1818)
RST Output Sink Current 8 mA VCC ≥ 2.7 V, reset not asserted, VOUT = 0.4 V (ADM1812/ADM1817)
OUTPUT VOLTAGE VCC − 0.5 VCC − 0.1 V ADM1810/ADM1812/ADM1815/ADM1817 at 0 µA to 500 µA
VCC TRIP POINT
ADM1810-5, ADM1811-5, 4.50 4.62 4.75 V
ADM1812-5, ADM1813-5
ADM1810-10, ADM1811-10, 4.25 4.35 4.49 V
ADM1812-10, ADM1813-10
ADM1815-5, ADM1816-5, 2.98 3.06 3.15 V
ADM1817-5, ADM1818-5
ADM1815-10, ADM1816-10, 2.80 2.88 2.97 V
ADM1817-10, ADM1818-10
ADM1815-20, ADM1816-20, 2.47 2.55 2.64 V
ADM1817-20, ADM1818-20
ADM1815-R23, ADM1816-R23, 2.25 2.31 2.37 V
ADM1817-R23, ADM1818-R23
ADM1815-R22, ADM1816-R22, 2.12 2.18 2.25 V
ADM1817-R22, ADM1818-R22
INTERNAL PULL-UP RESISTOR
ADM1811/ADM1816 3.5 5.5 7.5 kΩ
ADM1813/ADM1818 3.1 5.5 7.5 kΩ
OUTPUT CAPACITANCE 10 pF
RESET ACTIVE TIME 100 150 250 ms
VCC DETECT TO RESET
Falling 10 µs
Rising 100 150 250 ms tR = 5 µs
PUSH-BUTTON DETECT TO RST 1 µs ADM1813/ADM1818
PUSH-BUTTON RESET 100 150 250 ms ADM1813/ADM1818

Rev. F | Page 3 of 12
ADM1810 to ADM1813/ADM1815 to ADM1818 Data Sheet

ABSOLUTE MAXIMUM RATINGS

TA = 25°C, unless otherwise noted. Stresses above those listed under Absolute Maximum Ratings
Table 2. may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
Parameter Rating
other conditions above those indicated in the operational
VCC −0.3 V to +6.0 V
section of this specification is not implied. Exposure to absolute
Input Current 20 mA
maximum rating conditions for extended periods may affect
Operating Temperature Range −40°C to +105°C
device reliability.
Storage Temperature Range −65°C to +150°C
θJA Thermal Impedance, SOT-23 270°C/W ESD CAUTION
θJA Thermal Impedance, SC70 146°C/W
Lead Temperature (Soldering, 10 sec) 300°C
Vapor Phase (60 sec) 215°C
Infrared (15 sec) 220°C

Rev. F | Page 4 of 12
Data Sheet ADM1810 to ADM1813/ADM1815 to ADM1818

PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS

RST/RST 1 VCC 1

ADM181x ADM181x
TOP VIEW 3 GND TOP VIEW 3 GND
(Not to Scale) (Not to Scale)

00064-002

00064-014
VCC 2 RST/RST 2

Figure 2. 3-Lead SOT-23 Pin Configuration Figure 3. 3-Lead SC70 Pin Configuration

Table 3. Pin Function Descriptions

Pin No.
SOT-23 SC70 Mnemonic Description
1 2 RST Active High Reset Output. RST remains high while VCC is below the reset threshold and remains high for
150 ms typical after VCC rises above the reset threshold. Applies to the ADM1812 and ADM1817 only.
RST Active Low Reset Output. RST remains low while VCC is below the reset threshold and remains low for
150 ms typical after VCC rises above the reset threshold. Applies to the ADM1810, ADM1811, ADM1813,
ADM1815, ADM1816, and ADM1818 only.
2 1 VCC Supply Voltage. The supply voltage being monitored.
3 3 GND Ground. 0 V ground reference for all signals.

Rev. F | Page 5 of 12
ADM1810 to ADM1813/ADM1815 to ADM1818 Data Sheet

TYPICAL PERFORMANCE CHARACTERISTICS

10 1.011

1.009
ICC @VCC = 5.5V

NORMALIZED RESET THRESHOLD

8
1.007

1.005
6 DEVIATION (RISE)
ICC (µA)

ICC @VCC = 3V
1.003
DEVIATION (FALL)
4
1.001

0.999
2
0.997

00064-003

00064-006
0 0.995
–40 –20 0 20 30 50 70 85 100 120 –40 –20 0 20 30 50 70 85 100 120
TEMPERATURE (°C) TEMPERATURE (°C)

Figure 4. Supply Current vs. Temperature Figure 7. Normalized Reset Threshold vs. Temperature

900 60

800
50
POWER-DOWN RESET DELAY (µs)

700
MAXIMUM TRANSIENT (µs)
600 40

500
VOD = 20mV 30
400

300 20
VOD = 125mV
200
10
00064-004

00064-007
100
VOD = 200mV
0 0
–40 –20 0 20 30 50 70 85 100 120 10 30 40 60 80 100 200 400 600 800 1000
TEMPERATURE (°C) VTH – VCC (mV)

Figure 5. Power-Down Reset Delay vs. Temperature Figure 8. Maximum Transient Duration Without Causing a Reset Pulse vs.
Reset Comparator Overdrive
380

370
POWER-UP RESET TIMEOUT (ms)

360

350

340

330

320

310
00064-005

300

290
–40 –20 0 20 30 50 70 85 100 120
TEMPERATURE (°C)

Figure 6. Power-Up Reset Timeout vs. Temperature

Rev. F | Page 6 of 12
Data Sheet ADM1810 to ADM1813/ADM1815 to ADM1818

THEORY OF OPERATION
TIMING DIAGRAMS FOR ALL DEVICES PUSH-BUTTON TIME
RESET TIMEOUT
The following two timing diagrams are valid for ADM1810, VOLTAGE
ADM1811, ADM1812, ADM1813, ADM1815, ADM1816, INPUT HIGH

00064-011
ADM1817, and ADM1818. VOLTAGE
INPUT LOW
VCC
VCC TRIP POINT (MAX) Figure 12. Push-Button Reset Timing Diagram
VCC TRIP POINT
VCC TRIP POINT (MIN) The ADM1818 range has 2.88 V and 2.55 V (typical) trip point
VCC TO RESET options that allow the user to monitor 3.3 V and 3 V supplies.
RST DELAY
For 5 V monitoring requirements, the ADM1813 range has 4.62 V
and 4.35 V (typical) trip point options.
ADM1810, ADM1812, ADM1815, AND ADM1817

00064-008
VOL

The ADM1812 is a 5 V supply monitor with an active high

Figure 9. Power-Down Timing Diagram
push-pull output and trip point options of 4.62 V and 4.35 V
typical. The ADM1810 is similar to the ADM1812, except that
the ADM1810 has an active low push-pull output stage. The
VCC TRIP POINT (MAX)
ADM1817 is suitable for monitoring 3.3 V, 3 V, and 2.5 V
VCC TRIP POINT
VCC TRIP POINT (MIN)
supplies, with an active high push-pull output and trip point
VCC
options of 3.06 V, 2.88 V, 2.55 V, 2.31 V, and 2.18 V typical.
RESET ACTIVE TIMEOUT The ADM1815 is similar to the ADM1817, except that the
ADM1815 has an active low push-pull output stage.
The ADM1810/ADM1812/ADM1815/ADM1817 can connect
directly to most microprocessor reset inputs without the need
00064-009

RST
for external components.
VCC
Figure 10. Power-Up Timing Diagram

ADM1813 AND ADM1818 ADM1810/

ADM1812/
MICRO-
PROCESSOR

The ADM1813 and ADM1818 are low cost voltage monitoring ADM1815/
ADM1817
devices featuring an open-drain with internal pull-up resistor VCC
output and optional push-button reset function. RST/RST RESET
VCC GND

00064-012
ADM1813/ MICRO-
ADM1818 PROCESSOR

VCC Figure 13. ADM1810/ADM1812/ADM1815/ADM1817 Typical Application

RST RESET

ADM1811 AND ADM1816

GND
The ADM1811 is a 5 V supply monitor with an active low open-
drain with internal pull-up resistor output and trip point options of
00064-010

4.62 V and 4.35 V typical. The ADM1816 also has an active low
open-drain with internal pull-up resistor output but is suitable
Figure 11. ADM1813/ADM1818 Typical Application for monitoring lower voltage supplies of 3.3 V, 3 V, and 2.5 V.
An optional push-button reset switch can be connected VCC

between RST and ground. Pressing this switch pulls the reset ADM1811/ MICRO-
PROCESSOR
output low. If the push-button reset button pulls the RST output ADM1816

low for a period greater than 1 µs when the reset button releases
the RST line to float high, then the RST line stays low for another VCC

150 ms typical. RST RESET

GND
00064-013

Figure 14. ADM1811/ADM1816 Typical Application

Rev. F | Page 7 of 12
ADM1810 to ADM1813/ADM1815 to ADM1818 Data Sheet

OUTLINE DIMENSIONS
3.04
2.90
2.80
1.40
1.30
1.20 3 2.64
2.10
1 2

0.60 1.03
0.45 0.89
2.05
1.02 1.78
0.95 0.54
REF
0.88 1.12 GAUGE
PLANE
0.89
0.100 0.180
0.013 0.085
0.51
SEATING 0.25
PLANE 0.37 0.60 MAX
0.30 MIN

011909-C
COMPLIANT TO JEDEC STANDARDS TO-236-AB

Figure 15. 3-Lead Small Outline Transistor Package [SOT-23]

(RT-3)
Dimensions shown in millimeters

2.20
2.00
1.80
1.35
1.25
1.15 3 2.40
2.10
1 2 1.80

0.65 BSC

1.00 1.10 0.40

0.80 0.80 0.10

0.26 0.30
0.10 MAX 0.40 SEATING 0.20
0.25 0.10
COPLANARITY PLANE 0.10
0.10
072809-A

ALL DIMENSIONS COMPLIANT WITH EIAJ SC70

Figure 16. 3-Lead Thin Shrink Small Outline Transistor Package [SC70]
(KS-3)
Dimensions shown in millimeters

Rev. F | Page 8 of 12
Data Sheet ADM1810 to ADM1813/ADM1815 to ADM1818
ORDERING GUIDE
Model 1, 2 Temperature Range Trip Point Package Option Branding
ADM1810-5AKSZ-REEL −40°C to +105°C 4.62 V KS-3 (SC70) M4Y
ADM1810-5AKSZ-RL7 −40°C to +105°C 4.62 V KS-3 (SC70) M4Y
ADM1810-5ART-REEL7 −40°C to +105°C 4.62 V RT-3 (SOT-23) MZV
ADM1810-5ARTZ-REEL −40°C to +105°C 4.62 V RT-3 (SOT-23) M4Y
ADM1810-5ARTZ-RL7 −40°C to +105°C 4.62 V RT-3 (SOT-23) M4Y
ADM1810-10AKS-RL7 −40°C to +105°C 4.35 V KS-3 (SC70) MZT
ADM1810-10AKSZ-RL −40°C to +105°C 4.35 V KS-3 (SC70) M4Z
ADM1810-10AKSZ-RL7 −40°C to +105°C 4.35 V KS-3 (SC70) M4Z
ADM1810-10ARTZ-RL −40°C to +105°C 4.35 V RT-3 (SOT-23) M4Z
ADM1810-10ARTZ-RL7 −40°C to +105°C 4.35 V RT-3 (SOT-23) M4Z
ADM1811-5AKS-RL7 −40°C to +105°C 4.62 V KS-3 (SC70) M1V
ADM1811-5AKSZ-REEL −40°C to +105°C 4.62 V KS-3 (SC70) M6Z
ADM1811-5AKSZ-RL7 −40°C to +105°C 4.62 V KS-3 (SC70) M6Z
ADM1811-5ART-REEL −40°C to +105°C 4.62 V RT-3 (SOT-23) M1V
ADM1811-5ART-REEL7 −40°C to +105°C 4.62 V RT-3 (SOT-23) M1V
ADM1811-5ARTZ-REEL −40°C to +105°C 4.62 V RT-3 (SOT-23) M6Z
ADM1811-5ARTZ-RL7 −40°C to +105°C 4.62 V RT-3 (SOT-23) M6Z
ADM1811-10AKS-RL7 −40°C to +105°C 4.35 V KS-3 (SC70) M1T
ADM1811-10AKSZ-RL −40°C to +105°C 4.35 V KS-3 (SC70) M70
ADM1811-10AKSZ-RL7 −40°C to +105°C 4.35 V KS-3 (SC70) M70
ADM1811-10ART-REEL −40°C to +105°C 4.35 V RT-3 (SOT-23) M1T
ADM1811-10ARTZ-RL −40°C to +105°C 4.35 V RT-3 (SOT-23) M70
ADM1811-10ARTZ-RL7 −40°C to +105°C 4.35 V RT-3 (SOT-23) M70
ADM1812-5AKS-RL7 −40°C to +105°C 4.62 V KS-3 (SC70) MTV
ADM1812-5AKSZ-REEL −40°C to +105°C 4.62 V KS-3 (SC70) M72
ADM1812-5AKSZ-RL7 −40°C to +105°C 4.62 V KS-3 (SC70) M72
ADM1812-5ART-REEL7 −40°C to +105°C 4.62 V RT-3 (SOT-23) MTV
ADM1812-5ARTZ-REEL −40°C to +105°C 4.62 V RT-3 (SOT-23) M72
ADM1812-5ARTZ-RL7 −40°C to +105°C 4.62 V RT-3 (SOT-23) M72
ADM1812-10AKS-RL7 −40°C to +105°C 4.35 V KS-3 (SC70) MTT
ADM1812-10AKSZ-RL −40°C to +105°C 4.35 V KS-3 (SC70) M71
ADM1812-10AKSZ-RL7 −40°C to +105°C 4.35 V KS-3 (SC70) M71
ADM1812-10ART-RL7 −40°C to +105°C 4.35 V RT-3 (SOT-23) MTT
ADM1812-10ARTZ-RL −40°C to +105°C 4.35 V RT-3 (SOT-23) M71
ADM1812-10ARTZ-RL7 −40°C to +105°C 4.35 V RT-3 (SOT-23) M71
ADM1813-5AKS-REEL −40°C to +105°C 4.62 V KS-3 (SC70) M3V
ADM1813-5AKS-RL7 −40°C to +105°C 4.62 V KS-3 (SC70) M3V
ADM1813-5AKSZ-REEL −40°C to +105°C 4.62 V KS-3 (SC70) M6X
ADM1813-5AKSZ-RL7 −40°C to +105°C 4.62 V KS-3 (SC70) M6X
ADM1813-5ART-RL7 −40°C to +105°C 4.62 V RT-3 (SOT-23) M3V
ADM1813-5ARTZ-RL −40°C to +105°C 4.62 V RT-3 (SOT-23) M6X
ADM1813-5ARTZ-RL7 −40°C to +105°C 4.62 V RT-3 (SOT-23) M6X
ADM1813-10AKS-REEL −40°C to +105°C 4.35 V KS-3 (SC70) M3T
ADM1813-10AKS-RL7 −40°C to +105°C 4.35 V KS-3 (SC70) M3T
ADM1813-10AKSZ-RL −40°C to +105°C 4.35 V KS-3 (SC70) M6Y
ADM1813-10AKSZ-RL7 −40°C to +105°C 4.35 V KS-3 (SC70) M6Y
ADM1813-10ART-REEL −40°C to +105°C 4.35 V RT-3 (SOT-23) M3T
ADM1813-10ART-RL7 −40°C to +105°C 4.35 V RT-3 (SOT-23) M3T
ADM1813-10ARTZ-RL −40°C to +105°C 4.35 V RT-3 (SOT-23) M6Y
ADM1813-10ARTZ-RL7 −40°C to +105°C 4.35 V RT-3 (SOT-23) M6Y

Rev. F | Page 9 of 12
ADM1810 to ADM1813/ADM1815 to ADM1818 Data Sheet
Model 1, 2 Temperature Range Trip Point Package Option Branding
ADM1815-5AKS-RL7 −40°C to +105°C 3.06 V KS-3 (SC70) M5K
ADM1815-5AKSZ-REEL −40°C to +105°C 3.06 V KS-3 (SC70) M73
ADM1815-5AKSZ-RL7 −40°C to +105°C 3.06 V KS-3 (SC70) M73
ADM1815-5ART-REEL7 −40°C to +105°C 3.06 V RT-3 (SOT-23) M5K
ADM1815-5ARTZ-REEL −40°C to +105°C 3.06 V RT-3 (SOT-23) M73
ADM1815-5ARTZ-RL7 −40°C to +105°C 3.06 V RT-3 (SOT-23) M73
ADM1815-10AKS-RL7 −40°C to +105°C 2.88 V KS-3 (SC70) M5E
ADM1815-10AKSZ-RL −40°C to +105°C 2.88 V KS-3 (SC70) M4F
ADM1815-10AKSZ-RL7 −40°C to +105°C 2.88 V KS-3 (SC70) M4F
ADM1815-10ART-REEL −40°C to +105°C 2.88 V RT-3 (SOT-23) M5E
ADM1815-10ART-RL7 −40°C to +105°C 2.88 V RT-3 (SOT-23) M5E
ADM1815-10ARTZ-RL −40°C to +105°C 2.88 V RT-3 (SOT-23) M4F
ADM1815-10ARTZ-RL7 −40°C to +105°C 2.88 V RT-3 (SOT-23) M4F
ADM1815-20AKSZ-RL −40°C to +105°C 2.55 V KS-3 (SC70) M76
ADM1815-20AKSZ-RL7 −40°C to +105°C 2.55 V KS-3 (SC70) M76
ADM1815-20ART-RL7 −40°C to +105°C 2.55 V RT-3 (SOT-23) M5A
ADM1815-20ARTZ-RL7 −40°C to +105°C 2.55 V RT-3 (SOT-23) M76
ADM1815-R22AKSZ-RL −40°C to +105°C 2.18 V KS-3 (SC70) M74
ADM1815-R22AKSZ-R7 −40°C to +105°C 2.18 V KS-3 (SC70) M74
ADM1815-R22ART-RL7 −40°C to +105°C 2.18 V RT-3 (SOT-23) M5B
ADM1815-R22ARTZ-RL −40°C to +105°C 2.18 V RT-3 (SOT-23) M74
ADM1815-R22ARTZ-R7 −40°C to +105°C 2.18 V RT-3 (SOT-23) M74
ADM1815-R23AKSZ-RL −40°C to +105°C 2.31 V KS-3 (SC70) M75
ADM1815-R23AKSZ-R7 −40°C to +105°C 2.31 V KS-3 (SC70) M75
ADM1815-R23ART-RL7 −40°C to +105°C 2.31 V RT-3 (SOT-23) M5C
ADM1815-R23ARTZ-RL −40°C to +105°C 2.31 V RT-3 (SOT-23) M75
ADM1815-R23ARTZ-R7 −40°C to +105°C 2.31 V RT-3 (SOT-23) M75
ADM1816-5AKS-REEL7 −40°C to +105°C 3.06 V KS-3 (SC70) M6K
ADM1816-5AKSZ-REEL −40°C to +105°C 3.06 V KS-3 (SC70) M77
ADM1816-5AKSZ-RL7 −40°C to +105°C 3.06 V KS-3 (SC70) M77
ADM1816-5ART-REEL7 −40°C to +105°C 3.06 V RT-3 (SOT-23) M6K
ADM1816-5ARTZ-REEL −40°C to +105°C 3.06 V RT-3 (SOT-23) M77
ADM1816-5ARTZ-RL7 −40°C to +105°C 3.06 V RT-3 (SOT-23) M77
ADM1816-10AKSZ-RL −40°C to +105°C 2.88 V KS-3 (SC70) M54
ADM1816-10AKSZ-RL7 −40°C to +105°C 2.88 V KS-3 (SC70) M54
ADM1816-10ART-REEL −40°C to +105°C 2.88 V RT-3 (SOT-23) M6E
ADM1816-10ART-RL7 −40°C to +105°C 2.88 V RT-3 (SOT-23) M6E
ADM1816-10ARTZ-RL −40°C to +105°C 2.88 V RT-3 (SOT-23) M54
ADM1816-10ARTZ-RL7 −40°C to +105°C 2.88 V RT-3 (SOT-23) M54
ADM1816-20AKS-RL7 −40°C to +105°C 2.55 V KS-3 (SC70) M6A
ADM1816-20AKSZ-RL −40°C to +105°C 2.55 V KS-3 (SC70) M6H
ADM1816-20AKSZ-RL7 −40°C to +105°C 2.55 V KS-3 (SC70) M6H
ADM1816-20ART-RL7 −40°C to +105°C 2.55 V RT-3 (SOT-23) M6A
ADM1816-20ARTZ-RL −40°C to +105°C 2.55 V RT-3 (SOT-23) M6H
ADM1816-20ARTZ-RL7 −40°C to +105°C 2.55 V RT-3 (SOT-23) M6H

Rev. F | Page 10 of 12
Data Sheet ADM1810 to ADM1813/ADM1815 to ADM1818
Model 1, 2 Temperature Range Trip Point Package Option Branding
ADM1816-R22AKS-RL7 −40°C to +105°C 2.18 V KS-3 (SC70) M6B
ADM1816-R22AKSZ-RL −40°C to +105°C 2.18 V KS-3 (SC70) M78
ADM1816-R22AKSZ-R7 −40°C to +105°C 2.18 V KS-3 (SC70) M78
ADM1816-R22ART-RL7 −40°C to +105°C 2.18 V RT-3 (SOT-23) M6B
ADM1816-R22ARTZ-RL −40°C to +105°C 2.18 V RT-3 (SOT-23) M78
ADM1816-R22ARTZ-R7 −40°C to +105°C 2.18 V RT-3 (SOT-23) M78
ADM1816-R23AKSZ-RL −40°C to +105°C 2.31 V KS-3 (SC70) M79
ADM1816-R23AKSZ-R7 −40°C to +105°C 2.31 V KS-3 (SC70) M79
ADM1816-R23ART-RL7 −40°C to +105°C 2.31 V RT-3 (SOT-23) M6C
ADM1816-R23ARTZ-RL −40°C to +105°C 2.31 V RT-3 (SOT-23) M79
ADM1816-R23ARTZ-R7 −40°C to +105°C 2.31 V RT-3 (SOT-23) M79
ADM1817-5AKSZ-REEL −40°C to +105°C 3.06 V KS-3 (SC70) M7F
ADM1817-5AKSZ-RL7 −40°C to +105°C 3.06 V KS-3 (SC70) M7F
ADM1817-5ART-REEL7 −40°C to +105°C 3.06 V RT-3 (SOT-23) M7K
ADM1817-5ARTZ-REEL −40°C to +105°C 3.06 V RT-3 (SOT-23) M7F
ADM1817-5ARTZ-RL7 −40°C to +105°C 3.06 V RT-3 (SOT-23) M7F
ADM1817-10AKS-RL7 −40°C to +105°C 2.88 V KS-3 (SC70) M7E
ADM1817-10AKSZ-RL −40°C to +105°C 2.88 V KS-3 (SC70) M7G
ADM1817-10AKSZ-RL7 −40°C to +105°C 2.88 V KS-3 (SC70) M7G
ADM1817-10ART-REEL −40°C to +105°C 2.88 V RT-3 (SOT-23) M7E
ADM1817-10ART-RL7 −40°C to +105°C 2.88 V RT-3 (SOT-23) M7E
ADM1817-10ARTZ-RL −40°C to +105°C 2.88 V RT-3 (SOT-23) M7G
ADM1817-10ARTZ-RL7 −40°C to +105°C 2.88 V RT-3 (SOT-23) M7G
ADM1817-20AKSZ-RL −40°C to +105°C 2.55 V KS-3 (SC70) M7H
ADM1817-20AKSZ-RL7 −40°C to +105°C 2.55 V KS-3 (SC70) M7H
ADM1817-20ART-RL7 −40°C to +105°C 2.55 V RT-3 (SOT-23) M7A
ADM1817-20ARTZ-RL −40°C to +105°C 2.55 V RT-3 (SOT-23) M7H
ADM1817-20ARTZ-RL7 −40°C to +105°C 2.55 V RT-3 (SOT-23) M7H
ADM1817-R22AKSZ-RL −40°C to +105°C 2.18 V KS-3 (SC70) M7J
ADM1817-R22AKSZ-R7 −40°C to +105°C 2.18 V KS-3 (SC70) M7J
ADM1817-R22ART-RL7 −40°C to +105°C 2.18 V RT-3 (SOT-23) M7B
ADM1817-R22ARTZ-RL −40°C to +105°C 2.18 V RT-3 (SOT-23) M7J
ADM1817-R22ARTZ-R7 −40°C to +105°C 2.18 V RT-3 (SOT-23) M7J
ADM1817-R23AKSZ-RL −40°C to +105°C 2.31 V KS-3 (SC70) M7L
ADM1817-R23AKSZ-R7 −40°C to +105°C 2.31 V KS-3 (SC70) M7L
ADM1817-R23ART-RL7 −40°C to +105°C 2.31 V RT-3 (SOT-23) M7C
ADM1817-R23ARTZ-RL −40°C to +105°C 2.31 V RT-3 (SOT-23) M7L
ADM1817-R23ARTZ-R7 −40°C to +105°C 2.31 V RT-3 (SOT-23) M7L
ADM1818-5AKS-REEL −40°C to +105°C 3.06 V KS-3 (SC70) M8K
ADM1818-5AKSZ-RL7 −40°C to +105°C 3.06 V KS-3 (SC70) M4T
ADM1818-5ART-REEL7 −40°C to +105°C 3.06 V RT-3 (SOT-23) M8K
ADM1818-5ARTZ-REEL −40°C to +105°C 3.06 V RT-3 (SOT-23) M4T
ADM1818-5ARTZ-RL7 −40°C to +105°C 3.06 V RT-3 (SOT-23) M4T
ADM1818-10AKS-RL7 −40°C to +105°C 2.88 V KS-3 (SC70) M8E
ADM1818-10AKSZ-RL −40°C to +105°C 2.88 V KS-3 (SC70) M7P
ADM1818-10AKSZ-RL7 −40°C to +105°C 2.88 V KS-3 (SC70) M7P
ADM1818-10ART-REEL −40°C to +105°C 2.88 V RT-3 (SOT-23) M8E
ADM1818-10ART-RL7 −40°C to +105°C 2.88 V RT-3 (SOT-23) M8E
ADM1818-10ARTZ-RL7 −40°C to +105°C 2.88 V RT-3 (SOT-23) M7P

Rev. F | Page 11 of 12
ADM1810 to ADM1813/ADM1815 to ADM1818 Data Sheet
Model 1, 2 Temperature Range Trip Point Package Option Branding
ADM1818-20AKSZ-RL −40°C to +105°C 2.55 V KS-3 (SC70) M59
ADM1818-20AKSZ-RL7 −40°C to +105°C 2.55 V KS-3 (SC70) M59
ADM1818-20ART-REEL −40°C to +105°C 2.55 V RT-3 (SOT-23) M8A
ADM1818-20ART-RL7 −40°C to +105°C 2.55 V RT-3 (SOT-23) M8A
ADM1818-20ARTZ-RL7 −40°C to +105°C 2.55 V RT-3 (SOT-23) M59
ADM1818-R22AKS-RL −40°C to +105°C 2.18 V KS-3 (SC70) M8B
ADM1818-R22AKS-RL7 −40°C to +105°C 2.18 V KS-3 (SC70) M8B
ADM1818-R22AKSZ-RL −40°C to +105°C 2.18 V KS-3 (SC70) M7M
ADM1818-R22AKSZ-R7 −40°C to +105°C 2.18 V KS-3 (SC70) M7M
ADM1818-R22ART-RL −40°C to +105°C 2.18 V RT-3 (SOT-23) M8B
ADM1818-R22ART-RL7 −40°C to +105°C 2.18 V RT-3 (SOT-23) M8B
ADM1818-R23AKS-RL7 −40°C to +105°C 2.31 V KS-3 (SC70) M8C
ADM1818-R23AKSZ-RL −40°C to +105°C 2.31 V KS-3 (SC70) M7N
ADM1818-R23AKSZ-R7 −40°C to +105°C 2.31 V KS-3 (SC70) M7N
ADM1818-R23ART-RL −40°C to +105°C 2.31 V RT-3 (SOT-23) M8C
ADM1818-R23ART-RL7 −40°C to +105°C 2.31 V RT-3 (SOT-23) M8C
1
Available only in reels.
2
Z = RoHS Compliant Part.

©1999–2013 Analog Devices, Inc. All rights reserved. Trademarks and

registered trademarks are the property of their respective owners.
D00064-0-10/13(F)

Rev. F | Page 12 of 12
Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Analog Devices Inc.:

ADM1810-10AKSZ-RL ADM1816-5ART-REEL7 ADM1812-10ART-RL7 ADM1817-R22AKSZ-R7 ADM1818-
20ARTZ-RL7 ADM1815-R22ARTZ-R7 ADM1815-10ART-RL7 ADM1815-R22AKSZ-RL ADM1813-10AKS-REEL
ADM1816-20AKSZ-RL ADM1817-20ARTZ-RL ADM1818-10AKSZ-RL7 ADM1817-R22ARTZ-RL ADM1817-10AKSZ-
RL ADM1810-5ARTZ-REEL ADM1813-5AKSZ-REEL ADM1815-5AKS-RL7 ADM1817-10ART-RL7 ADM1816-
R23ARTZ-R7 ADM1818-R22ART-RL7 ADM1815-10AKS-RL7 ADM1817-5ART-REEL7 ADM1815-5ARTZ-RL7
ADM1816-10AKSZ-RL7 ADM1818-5ARTZ-REEL ADM1810-10ARTZ-RL7 ADM1816-20AKSZ-RL7 ADM1818-
R23AKS-RL7 ADM1818-10ARTZ-RL7 ADM1813-5ART-RL7 ADM1818-5ARTZ-RL7 ADM1816-R22AKS-RL7
ADM1816-20ARTZ-RL7 ADM1813-10ART-REEL ADM1812-5ART-REEL7 ADM1815-R23ART-RL7 ADM1817-
5ARTZ-REEL ADM1816-R23ARTZ-RL ADM1818-20AKSZ-RL7 ADM1811-10ARTZ-RL ADM1816-5AKSZ-REEL
ADM1815-20AKSZ-RL ADM1811-5ARTZ-REEL ADM1818-R22AKS-RL ADM1816-R23ART-RL7 ADM1815-20ARTZ-
RL7 ADM1816-R22ARTZ-R7 ADM1813-5ARTZ-RL7 ADM1811-5AKS-RL7 ADM1816-20ARTZ-RL ADM1811-5ART-
REEL ADM1818-20ART-REEL ADM1811-10ARTZ-RL7 ADM1817-10ARTZ-RL7 ADM1818-10AKS-RL7 ADM1812-
10AKS-RL7 ADM1810-5AKSZ-REEL ADM1816-5AKSZ-RL7 ADM1813-5AKSZ-RL7 ADM1813-5AKS-RL7
ADM1817-10AKS-RL7 ADM1817-20ART-RL7 ADM1817-R23ARTZ-RL ADM1818-20ART-RL7 ADM1816-R22AKSZ-
RL ADM1815-R22AKSZ-R7 ADM1815-R22ART-RL7 ADM1818-20AKSZ-RL ADM1810-5ART-REEL7 ADM1816-
10AKSZ-RL ADM1818-10ART-RL7 ADM1818-10AKSZ-RL ADM1813-10AKSZ-RL ADM1818-5ART-REEL7
ADM1816-5ARTZ-RL7 ADM1817-R23AKSZ-RL ADM1811-10AKS-RL7 ADM1816-5ARTZ-REEL ADM1815-5ART-
REEL7 ADM1813-10ARTZ-RL ADM1815-20AKSZ-RL7 ADM1818-R23AKSZ-RL ADM1810-5ARTZ-RL7 ADM1816-
R23AKSZ-RL ADM1813-10AKSZ-RL7 ADM1817-10ARTZ-RL ADM1817-5AKSZ-REEL ADM1818-R22AKSZ-R7
ADM1816-10ART-REEL ADM1813-10ART-RL7 ADM1817-R23AKSZ-R7 ADM1817-5ARTZ-RL7 ADM1812-5ARTZ-
REEL ADM1813-5AKS-REEL ADM1817-R22AKSZ-RL ADM1816-R22ARTZ-RL ADM1815-10ART-REEL ADM1812-
5ARTZ-RL7 ADM1811-5ARTZ-RL7 ADM1816-5AKS-REEL7