Lead Free Solder Paste

Safety Data Sheet (SDS) www.chipquik.com

To comply with European CLP Regulation (EC) No. 1907/2006 (REACH), Annex II, as amended by Commission Regulation (EU) 2020/878, US 29CFR
1910.1200 OSHA's Hazard Communication Standard, and Australian NOHSC: 1008 [2004] and ADG Code 7.4

1. PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NAME: Chip Quik Lead Free Solder Paste Series: SMD291SNL, SMD4300SNL, SMDLTLFP, SMD4300LTLFP, TS391SNL, TS391LT,
NC191SNL, NC191LT, NC191LTA, RMA591SNL, RMA591LT, RMA591L0SNL, RMA591L0LT
SYNONYMS: Paste, Solder Cream
PART NUMBERS: SMD291SNL, SMD291SNL10, SMD291SNL10T4, SMD291SNL10T5, SMD291SNL50T3, SMD291SNL250T3,
SMD291SNL250T4, SMD291SNL250T5, SMD291SNL500T3, SMD291SNL500T5, SMD291SNL15T4, SMD291SNL60T4,
SMD4300SNL10, SMD4300SNL10T4, SMD4300SNL10T5, SMD4300SNL250T3, SMD4300SNL250T4, SMD4300SNL250T5,
SMDLTLFP, SMDLTLFP10, SMDLTLFP10T4, SMDLTLFP10T5, SMDLTLFP50T3, SMDLTLFP250T3, SMDLTLFP250T4,
SMDLTLFP250T5, SMDLTLFP500T3, SMDLTLFP15T4, SMDLTLFP60T4, LTLFP_10G, SMDTCLF, SMD291SNL500T3C,
SMD291SNL500T4C, SMD291SNL500T5C, SMD4300SNL500T3C, SMD4300SNL500T4C, SMD4300SNL500T5C,
SMDLTLFP500T3C, SMDLTLFP500T4C, SMDLTLFP500T5C, TS391SNL, TS391SNL10, TS391SNL50, TS391SNL250,
TS391SNL500C, TS391LT, TS391LT10, TS391LT50, TS391LT250, TS391LT500C, SMD4300LTLFP10T4,
SMD4300LTLFP250T4, SMD291SNLT4, SMD291SNLT5, SMDLTLFPT4, SMDLTLFPT5, SMD291SNL500T4, CQ100Ge 35g,
CQ100Ge 250g, SMD291SNLT6, SMD291SNL50T6, NC191LT10, NC191LT15, NC191LT35, NC191LT50, NC191LT250,
NC191LT15T5, NC191LT35T5, NC191LT50T5, NC191LT250T5, NC191SNL15, NC191SNL35, NC191SNL50,
NC191SNL250, NC191SNL15T5, NC191SNL35T5, NC191SNL50T5, NC191SNL250T5, SMD291SNLT7, SMD291SNL40T7,
NC191LTA10, NC191LTA15, NC191LTA35, NC191LTA50, NC191LTA250, NC191LTA15T5, NC191LTA35T5,
NC191LTA50T5, NC191LTA250T5, NC191LT500C, NC191LT500T5C, NC191SNL500C, NC191SNL500T5C,
NC191LTA500C, NC191LTA500T5C, TS991SNL500T3, TS991SNL500T4, WS991SNL500T4, WS991LT500T4,
TS991SNL35T3, TS991SNL35T4, WS991SNL35T4, WS991LT35T4, SMD291SNL10T6, RMA591SNL, RMA591SNL10,
RMA591SNL250, RMA591SNL500C, RMA591SNL50, RMA591LT, RMA591LT10, RMA591LT250, RMA591LT500C,
RMA591LT50, NI3300LTLFP15T3, NI3300LTLFP60T3, NI3300SNL15T3, NI3300SNL60T3, RMA591L0SNL,
RMA591L0SNL10, RMA591L0SNL250, RMA591L0SNL500C, RMA591L0SNL50, RMA591L0LT, RMA591L0LT10,
RMA591L0LT250, RMA591L0LT500C, RMA591L0LT50, NI3300LTLFP250T3, NI3300SNL250T3, SMDLTLFP250T4-2MIX,
SMD291SNL250T4-2MIX, SMDLTLFP10T5-67METAL-LT291, JET551SNL10T5, JET551SNL30T5, JET551LT10T5,
JET551LT30T5, SMDLTB35T4, SMDLTB250T4, WS991SNL50T4, WS991LT50T4, WS991LT500T4C, SMDLTLFPT6,
SMDLTLFP50T6, SMD291SAC405-35T3, SMD291SAC405-250T3, SMD291SAC405-500T3, SMDAU80SN20T5-5G,
SMD291SNL250T6, SMD4300SNL30T4, SMDLTLFP500T5

MANUFACTURER: Chip Quik Inc.

ADDRESS: 931-3909 Witmer Rd., Niagara Falls, NY 14305 (USA)
3rd Floor, 207 Regent Street, London W1B 3HH (UK)
13 Adelaide Road, Dublin, Ireland, D02 P950 (EU)
8-1500 Sandhill Dr., Ancaster, ON L9G 4V5 (Canada)
42A Crimea Street, C/O A03886, Parramatta, NSW, 2150 (Australia)
PHONE: (508) 477-2264
EMERGENCY PHONE: (800) 424-9300 (USA and Canada 24/7 CHEMTREC)
+44 20 3868 7152 (UK and EU 24/7)
+61 2 8607 7057 (Australia 24/7)

REVISION DATE: 2024/05/23

REVISION NUMBER: 7.2
REVISED BY: Chip Quik Product Safety

PRODUCT USE: Soldering components for bonding semiconductor chips and packages to circuit boards.

2. HAZARD IDENTIFICATION

NFPA 704:

Classified in accordance with European CLP Regulation 1272/2008

Acute Toxicity (oral) 4 H302

Acute Toxicity (dermal) 4 H312
Acute Toxicity (inhalation) 4 H332
Eye Irritant 2 H319
Skin Irritant 2 H315
Skin Sensitization 1 H317
Aquatic Acute 1 H400
Aquatic Chronic 1 H410
Specific Target Organ Toxicity (STOT) – Single Exposure (SE) Respiratory Tract Irritation 3 H335

CHEMICAL NAME: NA
CHEMICAL FAMILY: Mixture
CHEMICAL FORMULA: Proprietary

ROUTES OF ENTRY: Inhalation, Ingestion, Skin/Eye Contact

TARGET ORGANS: NA

GHS/CLP:

Signal Word: Warning

GHS/CLP LABEL ELEMENTS:

Hazard statement(s)
H302 Harmful if swallowed.
H312 Harmful in contact with skin.
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H332 Harmful if inhaled.
H335 May cause respiratory irritation.
H410 Very toxic to aquatic life with long lasting effects.

Precautionary statement(s)
P102 Keep out of reach of children.
P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P233 Keep container tightly closed.
P260 Do not breathe dust/fume/gas/mist/vapor/spray.
P262 Do not get in eyes, on skin, or on clothing.
P264 Wash hands thoroughly after handling.
P270 Do not eat, drink, or smoke when using this product.
P271 Use in a well-ventilated area.
P272 Contaminated work clothing should not be allowed out of the workplace.
P273 Avoid release to the environment.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P284 In case of inadequate ventilation wear respiratory protection.
P301/P330/P331/P310 IF SWALLOWED: Rinse mouth. DO NOT induce vomiting. Immediately call a POISON CENTER/Doctor.
P303/P361/P352/P333/P313 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Wash with soap & water. Get medical advice/attention if
skin irritation or rash occurs or if you feel unwell.
P304/P340/P312 IF INHALED: Remove victim to fresh air and keep comfortable for breathing. Call a POISON CENTER or doctor/physician if
you feel unwell.
P305/P351/P338/P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue
rinsing. Immediately call POISON CENTER/Doctor.
P308/P313 IF EXPOSED OR CONCERNED: Get medical advice/attention.
P342/P311 IF EXPERIENCING RESPIRATORY SYMPTOMS: Call POISON CENTER/Doctor.
P362 Take off contaminated clothing and wash it before reuse.
P391 Collect spillage.
P402/P404 Store in a dry place. Store in a closed container.
P405 Store locked up.
P501 Dispose of contents/container in accordance with local/regional/national/international regulations.

POTENTIAL HEALTH EFFECTS (CHRONIC and OVEREXPOSURE)

Tin: Dust or fumes may cause irritation of the skin mucous membranes and may result in a benign Pneumoconiosis (Stannosis).
Silver: May cause discoloration of eyes and skin (Argyia).
Bismuth: May cause foul breath, a blue-black line on the gums, and Stomatitis.
Antimony: May cause gastrointestinal upset, sleeplessness, irritability, and muscular pain.
Indium: May cause weight loss, pulmonary edema, blood damage and degenerative changes in liver and kidneys.

MEDICAL CONDITIONS POSSIBLY AGGRAVATED BY EXPOSURE: Diseases of the blood-forming organs, kidneys, nervous and possibly reproductive
systems. Occupational Asthma.

SECTION 2 NOTES:
Chip Quik Inc. does not recommend, manufacture, market, or endorse any of its products for human consumption.

3. COMPOSITION / INFORMATION ON INGREDIENTS

Classified in accordance with European CLP Regulation 1272/2008

 Hazardous Ingredients (1) C.A.S. Number Weight Percent OSHA PEL ACGIH TLV TWA LD 50 Ingested LD 50 Inhaled
mg/m3 mg/m3 g/Kg g/m3
Modified Rosins (Rosin) (2) 8050-09-7 <45 NE NE NE NE
Pine Oil Derivatives 8000-41-7 <5 NE NE NE NE
(Terpineol)
Mixed Carboxylic Acids 110-16-7 <4 NE NE NE NE
(Maleic Acid)(2)
Tin 7440-31-5 2.00 2.00 NE NE
Gold 7440-57-5 Product contains NE NE NE NE
one or more of
Silver 7440-22-4 0.01 0.10 NE NE
these metallic
Bismuth 7440-69-9 NE NE NE NE
elements in
Antimony 7440-36-0 0.50 0.50 7.0 Rat NE
varying
Indium 7440-74-6 percentages NE 0.10 NE NE
Copper 7440-50-8 1.00 1.00 NE NE

Non-Hazardous Ingredients C.A.S. Number Weight Percent OSHA PEL ACGIH TLV TWA LD 50 Ingested LD 50 Inhaled
mg/m3 mg/m3 g/Kg g/m3
Surfactants NA <4 NE NE NE NE
Rheological Modifier NA <5 NE NE NE NE

SECTION 3 NOTES:
(1) Per 29 CFR 1910 the mixture has not been tested as a whole. All hazardous components, which comprise 1% of the mixture (0.1% carcinogenic), are
listed. Percentages of individual components are not listed as this information is considered a trade secret.

(2) The identity of the specific chemical(s) is being withheld as a trade secret per 29 CFR 1910.1200. The hazardous properties of these ingredients are
disclosed in this SDS.

4. FIRST-AID MEASURES

Signs and symptoms of exposure: Inhalation-Nose and throat irritation, headache, dizziness, difficulty breathing, coughing. Ingestion-nausea, vomiting,
cramps. Skin-redness, burning, rash, dryness. Eye-redness, burning, tearing, blurred vision.

Emergency first aid procedures:

EYES: Flush with plenty of water, contact a physician. If contact lenses can be removed easily, flush eyes without contact lenses.

SKIN: Wash affected area with plenty of warm, soapy water. If irritation persists, seek medical attention.

INGESTION: Call a physician or Poison Control Center immediately. Do not induce vomiting. Drink large amounts of water. Never give anything by mouth
to an unconscious person

INHALATION: Remove to fresh air. Support respiration if required. If not breathing, seek immediate medical attention.

5. FIREFIGHTING MEASURES

EXTINGUISHING MEDIA: Dry chemical, foam

SPECIAL FIRE FIGHTING PROCEDURES: Do not use water. Use NIOSH-approved self-contained Breathing Apparatus and full protective clothing if
involved in a fire.

UNUSUAL FIRE AND EXPLOSION HAZARDS: May release Toxic metal and oxide fumes. High concentrations of dust may present explosion hazard.
Water trapped below molten metal may explode thus spattering molten metal.

SECTION 5 NOTES:
Molten solder alloys consisting of Antimony, Bismuth, Copper, Indium, Silver, and/or Tin do not produce significant quantities of fumes below 900° F.

6. ACCIDENTAL RELEASE MEASURES

PRECAUTIONS AND EQUIPMENT: Material is extremely thick and will not flow out.

ACCIDENTAL RELEASE MEASURES: If material spills or leaks use a spatula to collect and place it in a plastic or glass jar. Remove traces of residue
using cloth rags or paper towels moistened with Isopropyl Alcohol. Exposure to spilled material may be irritating. Follow on-site personal protective
equipment recommendations.

ENVIRONMENTAL PRECAUTIONS: Avoid release to the environment. Collect spillage.

SECTION 6 NOTES:
See Sections 2, 4, and 7 for additional information.

7. HANDLING AND STORAGE

HANDLING/STORAGE: Keep containers tightly closed when not in use. Use care to avoid spills. Avoid inhalation of fumes or dust. Avoid contact with
eyes, skin, and clothing. Store in a closed corrosive resistant container, with corrosive resistant liner, in cool dry place. Wear appropriate personal
protective equipment when working with or handling. Always wash hands thoroughly after handling this product. Dispose of following Federal,
State/Provincial, and Local regulations.

OTHER PRECAUTIONS: Empty containers may retain product residues in vapor, liquid, and/or solid form. All labeled hazard precautions should be
observed.
WORK HYGIENIC PRACTICES: Cosmetics/Food/Drink/Tobacco should not be consumed or used in work areas. Always wash hands after handling
material and before applying or using cosmetics/food/drink/tobacco.

SECTION 7 NOTES:
Keep out of reach of children.
Not for internal consumption.

8. EXPOSURE CONTROLS / PERSONAL PROTECTION

Occupational Exposure Limit Values:

Rosin flux fumes (as total resin acids)

MEL: 0.05 mg/m3 8h TWA.
MEL: 0.15 mg/m3 15 min.

Extraction is necessary to remove fumes evolved during reflow.

Also see section 3.

ENGINEERING CONTROLS: Use only with production equipment designed for use with solder paste.

VENTILATION: Provide sufficient mechanical (general and/or local exhaust) ventilation to maintain exposure below TLVs.

RESPIRATORY PROTECTION: A (US: NIOSH; EU: EN 140:1998, EN 14387:2004 A) approved air-purifying respirator with fume/organic chemical
cartridge should be worn when airborne concentrations may be exceeded. General and local exhaust ventilation is the preferred means of protection.

EYE PROTECTION: Use with appropriate eye protection: Goggles or face shield (EU: EN 166-S 3 9).

SKIN PROTECTION: Protective gloves should be worn when the possibility of skin contact exists (EU: EN 374-1:2003).

PROTECTIVE CLOTHING OR EQUIPMENT: Work clothes should be worn and laundered in accordance with current Lead (Pb) standards (US: OSHA).

WORK HYGIENIC PRACTICES: Cosmetics/Food/Drink/Tobacco should not be consumed or used in areas where solder products may be used. Always
wash hands after handling soldering products and before applying or using cosmetics/food/drink/tobacco.

OTHER: Maintain eye wash stations in work areas. Avoid the use of contact lenses in high fume areas. Clean protective equipment regularly. Clean up
spills immediately.

9. PHYSICAL AND CHEMICAL PROPERTIES

APPEARANCE: Grey paste

ODOR: Odorless
ODOR THRESHOLD: NE
pH as SUPPLIED: NA
MELTING POINT: Varies
FREEZING POINT: Varies
INITIAL BOILING POINT: Varies
BOILING RANGE: NA
FLASH POINT: NA
EVAPORATION RATE: NA
FLAMMABILITY (solid): NE
UPPER/LOWER FLAMMABILITY: NE
UPPER/LOWER EXPLOSIVE LIMITS: NE
VAPOR PRESSURE (mmHg): NA
VAPOR DENSITY (AIR = 1): NA
RELATIVE DENSITY: NE
SOLUBILITY IN WATER: Insoluble
PARTITION COEFFICIENT (n-octanol/water): NE
AUTOIGNITION TEMPERATURE: NE
DECOMPOSITION TEMPERATURE: NE
VISCOSITY: NA

9.2 Other Information

9.2.1 Information with regard to physical hazard classes
No additional information available.
9.2.2 Other safety characteristics
No additional information available.

SECTION 9 NOTES:
Other physical and chemical properties depend on alloy composition.

10. STABILITY AND REACTIVITY

STABILITY: Stable
CONDITIONS TO AVOID (STABILITY): NE
INCOMPATIBILITY (MATERIAL TO AVOID): Oxidizing materials, acids, hydrogen peroxide, bases
HAZARDOUS DECOMPOSITION/BY-PRODUCTS: Harmful organic fumes and toxic oxide fumes may form at elevated temperatures.
POSSIBILITY OF HAZARDOUS REACTIONS: NE
11. TOXICOLOGICAL INFORMATION

INHALATION:
This product does not present a risk at ambient temperatures. The flux fumes evolved during soldering will irritate the nose, throat and lungs. Repeated or
prolonged exposure to flux fumes may cause an allergic affect which may lead to occupational asthma.

SKIN:
Contact with flux fumes and flux residues may cause irritation and sensitization.

EYES:
Flux fumes may cause irritation.

Health Hazards (acute and chronic): Contact with dust and fumes may cause skin, eye and respiratory irritation. Ingestion and/or inhalation of material or
fumes may result in flu like symptoms, insomnia, muscle weakness, nausea and abdominal pain. Gross inhalation or ingestion may be toxic and can result
in death. Symptoms of toxicity may take hours or days to manifest. Chronic exposures, inhalation and ingestion, may result in kidney, red blood cell,
reproductive and nervous system effects. Health effects may be cumulative over many exposures. Studies show that health risks vary by individual.
Minimize exposure as a precaution. See OSHA 29CFR 1910.1025(subpart Z) for more information.

ACUTE TOXICITY:
Product/Ingredient Name Result Species Dose Exposure
Rosin LD50 Oral Rat 7600 mg/kg -
Terpineol LD50 Oral Rat 2000 mg/kg -
LD50 Inhalation Rat 4.76 mg/l 4 hours
LD50 Dermal Rat 2000 mg/kg -
Maleic acid LD50 Oral Rat 708 mg/kg Remarks: Behavioral:
Convulsions or effect on
seizure threshold.
Behavioral: Muscle
weakness. Gastrointestinal:
Ulceration or bleeding from
stomach.
LD50 Inhalation Rat 720 mg/m3 1 hour
LD 50 Dermal Rabbit 1560 mg//kg Remarks: Behavioral:
Tremor

SKIN CORRISION/IRRITATION: NE
SERIOUS EYE DAMAGE/IRRITATION: NA
RESPIRATORY OR SKIN SENSITIZATION: NE
GERM CELL MUTAGENICITY: NA
CARCINOGENICITY:
OSHA: NA ACGIH: NA NTP: NA IARC: NA

REPRODUCTIVE TOXICITY: NA
STOT-SINGLE EXPOSURE:
Product/Ingredient Name Category Route of exposure Target organs
Maleic acid Category 3 Not applicable Respiratory tract irritation

STOT-REPEATED EXPOSURE: NA
ASPIRATION HAZARD: NA

11.2 Information on other hazards:

11.2.1 Endocrine disrupting properties:
The substance/mixture does not contain components considered to have endocrine disrupting properties according to REACH Article 57(f) or Commission
Delegated regulation (EU) 2017/2100 or Commission Regulation (EU) 2018/605 at levels of 0.1% or higher.
11.2.2 Other information:
To the best of our knowledge, the information contained herein is accurate. However, neither the above-named manufacturer, nor any of its subsidiaries,
assumes any liability whatsoever for the accuracy or completeness of the information contained herein.
Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with
caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.

SECTION 11 NOTES:
This product has not been tested as a whole to determine its hazards. Synergistic or additive effects of the above chemicals are unknown, as are the effects
of exposure to these chemicals in addition to others present in the work place. See Section 2 for additional health hazards.

12. ECOLOGICAL INFORMATION

TOXICITY:
Product/Ingredient Name Result Species Exposure
Silver Acute EC50 1.4 μg/l Marine water Algae - Chroomonas sp. 4 days
Acute EC50 0.24 μg/l Fresh water Daphnia - Daphnia magna 48 hours
Acute LC50 11 μg/l Fresh water Crustaceans - Ceriodaphnia 48 hours
reticulata
Acute LC50 2.13 μg/l Fresh water Fish - Pimephales promelas 96 hours
Chronic NOEC 5 mg/l Marine Algae - Glenodinium halli 72 hours
water
Rosin Acute LC50 60.3 mg/l Fresh water Brachydanio rerio (zebra fish) 96 hours
Terpineol Acute LC50 62.80 mg/l Fresh Danio rerio (zebra fish) 96 hours
 water
Acute LC50 68 mg/l Marine water Algae – Pseudokirchneriella 72 hours
subcapitata (green algae)
Maleic acid Acute EC50 316200 μg/l Fresh Daphnia - Daphnia magna - 48 hours
water Larvae
Acute LC50 5000 μg/l Fresh water Fish - Pimephales promelas 96 hours
Copper Acute EC50 1100 μg/l Fresh water Aquatic plants - Lemna minor 4 days
Acute EC50 2.1 μg/l Fresh water Daphnia - Daphnia longispina - 48 hours
Juvenile (Fledgling, Hatchling,
Weanling)
Acute IC50 13 μg/l Fresh water Algae - Pseudokirchneriella 72 hours
subcapitata - Exponential
growth phase
Acute IC50 5.4 mg/l Marine water Aquatic plants - Plantae - 72 hours
Exponential growth phase
Acute LC50 0.072 μg/l Marine Crustaceans - Amphipoda - 48 hours
water Adult
Acute LC50 7.56 μg/l Marine water Fish - Periophthalmus waltoni - 96 hours
Adult
Chronic NOEC 2.5 μg/l Marine Algae - Nitzschia closterium - 72 hours
water Exponential growth phase
Chronic NOEC 7 mg/l Fresh water Aquatic plants - Ceratophyllum 3 days
demersum
Chronic NOEC 0.02 mg/l Fresh Crustaceans - Cambarus 21 days
water bartonii - Mature
Chronic NOEC 2 μg/l Fresh water Daphnia - Daphnia magna 21 days
Chronic NOEC 0.8 μg/l Fresh Fish - Oreochromis niloticus - 6 weeks
water Juvenile (Fledgling, Hatchling,
Weanling)

PERSISTENCE AND DEGRADIBILITY: NE

BIOACCUMULATIVE POTENTIAL:
Product/Ingredient Name LogPow BCF Potential
Silver - 70 Low
Rosin 1.9 to 7.7 - High
Terpineol NE
Maleic acid -1.3 - Low

MOBILITY IN SOIL: NE
RESULT OF PBT and vPvB ASSESSMENT: Not applicable
12.6 Endocrine Disrupting Properties: The substance/mixture does not contain components considered to have endocrine disrupting
properties according to REACH Article 57(f) or Commission Delegated regulation (EU)
2017/2100 or Commission Regulation (EU) 2018/605 at levels of 0.1% or higher
12.7 OTHER ADVERSE EFFECTS: No known significant effects or critical hazards

13. DISPOSAL CONSIDERATIONS

WASTE DISPOSAL METHOD: Scrap and waste should be recycled or stored in a dry, sealed container for later disposal. Disposal must be in accordance
with Federal, State/Provincial, and Local Regulations.

OTHER PRECAUTIONS: Avoid skin & eye contact, inhalation & ingestion of fumes and material. Wash contaminated clothing before reuse. Keep away
from children.

14. TRANSPORT INFORMATION

Product contains no components that are above dangerous goods toxic thresholds and therefore is not regulated for transport.

Transport in accordance with applicable regulations and requirements.

UN Number: Not available

UN Proper Shipping Name: Not available
Packaging Group: Not applicable
Environmental Hazards: None

TRANSPORT HAZARD CLASSES:

US DOT Hazardous Material Classification: Non-Hazardous
Water Transportation: Non-Hazardous
IATA Hazardous Material Classification: Non-Hazardous
ADR Road Regulations Not regulated
IMDG Sea Regulations Not regulated
ADG Land Transportation Not regulated

15. REGULATORY INFORMATION

United States Regulatory Information:

TSCA 8 (b) Inventory Status: All components are listed or are exempt from listing on the Toxic Substances Control Act
(TSCA) Inventory.
TSCA 12 (b) Export Notification: Not required.
Canada Regulatory Information:
CEPA DSL/NDSL Status: All components are listed on or are exempt from listing on the Canadian Domestic Substances
List.

U.S. FEDERAL REGULATIONS: Not regulated

STATE REGULATIONS: Not regulated
INTERNATIONAL REGULATIONS: Not regulated
AUSTRALIAN REGULATIONS: Not regulated

16. OTHER INFORMATION

LEGEND:
ACGIH American Conference of Governmental Industrial Hygienists
ADG Australian Dangerous Goods Code
ADR European Agreement concerning the International Carriage of Dangerous Goods by Road
AICS Australian Inventory of Chemical Substances
BCF Bioconcentration factor
C.A.S. Chemical Abstract Service
CLP Classification, Labeling and Packaging
DOT Department of Transportation
EC Effective Concentration
EPA Environmental Protection Agency
GHS Global Harmonized System
HMIS Hazardous Material Identification System
IARC International Agency for Research on Cancer
IATA International Air Transport Association
IMDG International Maritime Dangerous Goods Code
LC Lethal Concentration
LD Lethal Dose
NA Not available
NE Not established
NIOSH National Institute for Occupational Safety & Health
NOEC No observed effective concentration
NOHSC National Occupational Health and Safety Commission (Australia)
NTP National Toxicology Program
OSHA Occupational Safety and Health Administration
PEL Permissible Exposure Limit
Pow Octanol water partition coefficient
SDS Safety Data Sheet
STEL Short-Term Exposure Limit
STOT Specific target organ toxicity
TLV Threshold Limit Value
TSCA Toxic Substance Control Act
TWA: Time Weighted Average
US DOT: United States Department of Transportation

PREPARATION INFORMATION:
This update supersedes all previously released documents.

DISCLAIMER:
The information and recommendations contained within this publication have been compiled from sources believed to be reliable and to represent the best
information available to Chip Quik at the time of issue. No warranty, guarantee, or representation is made by Chip Quik nor does Chip Quik assume any
responsibility in connection there within; nor can it be assumed that all acceptable safety measures or other safety measures may not be required under
particular or exceptional conditions or circumstances. The data on this Safety Data Sheet relates only to this product and does not relate to use with any
other material or in any process. All chemical products should be used only by, or under the direction of, technically qualified personnel who are aware of
the hazards involved and necessity for reasonable care in handling. Hazard communication regulations require that employees must be trained on how to
use a Safety Data Sheet as a source for hazard information.

Copyright © 1994-2024 Chip Quik® Inc.