Icf 5012
Icf 5012
S-14712XZ-C1
Feb. 2011
INTRODUCTION CAUTION
This service manual describes the latest technical NEVER connect the transceiver to an AC outlet or to a DC
information for the IC-F5011, IC-F5012, IC-F5013 and power supply that uses more than the specified voltage.
IC-F5013H VHF MOBILE TRANSCEIVER, at the time of This will ruin the transceiver.
publication.
DO NOT expose the transceiver to rain, snow or any liquids.
CHANNEL DO NOT reverse the polarities of the power supply when
TX OUTPUT
MODEL VERSION SPACING connecting the transceiver.
POWER
(kHz)
IC-F5011 [USA-01] 12.5/25.0 50 W DO NOT apply an RF signal of more than 20 dBm (100 mW) to
IC-F5012 [EUR-01] 12.5/20.0/25.0 the antenna connector. This could damage the transceiver’s
25 W front-end.
IC-F5013 [EXP-01]
12.5/25.0
IC-F5013H [EXP-02] 50 W To upgrade quality, any electrical or mechanical parts
and internal circuits are subject to change without notice
or obligation.
Be sure to include the following four points when ordering 1. Make sure that the problem is internal before
replacement parts: disassembling the transceiver.
2. DO NOT open the transceiver until the transceiver is
1. 10-digit Icom part number disconnected from its power source.
2. Component name 3. DO NOT force any of the variable components. Turn
3. Equipment model name and unit name them slowly and smoothly.
4. Quantity required 4. DO NOT short any circuits or electronic parts. An
insulated tuning tool MUST be used for all adjustments.
<ORDER EXAMPLE> 5. DO NOT keep power ON for a long time when the
transceiver is defective.
1110007320 S.IC NJM2591V IC-F5012 MAIN UNIT 5 pieces
6. DO NOT transmit power into a Standard Signal
8820001210 Screw 2438 screw IC-F5013 Top cover 10 pieces
Generator or a Sweep Generator.
7. ALWAYS connect a 50 dB to 60 dB attenuator between
Addresses are provided on the inside back cover for your the transceiver and a Deviation Meter or Spectrum
convenience. Analyzer, when using such test equipment.
8. READ the instructions of the test equipment throughly
before connecting it to the transceiver.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the
United Kingdom, Germany, France, Spain, Russia and/or other countries.
TABLE OF CONTENTS
SECTION 1 SPECIFICATIONS
• Power supply requirement (Nominal) 13.6 V DC (Negative ground) 13.2 V DC (Negative ground)
• Current drain Stand-by 250 mA
RX
(Approximately) Max.audio 700 mA
at 25 W 5.0 A
TX
at 50 W* 10.0 A –
• Dimensions [25 W ver.] 150 (W) × 40 (H) × 117.5 (D) mm; 5.9 (W) × 1.6 (H) × 4.6 (D) in
(Projections not included) 150 (W) × 40 (H) × 167.5 (D) mm;
[50 W ver.] –
5.9 (W) × 1.6 (H) × 6.6 (D) in
• Weight [25 W ver.] 0.8 kg (1.8 Ib)
[50 W ver.] 1.1 kg (2.4 Ib) –
• Transmit output power [25 W ver.] 25 W (High), 10 W (Low2), 2.5 W (Low1)
[50 W ver.] 50 W (High), 25 W (Low2), 5.0 W (Low1) –
• Modulation Variable reactance frequency modulation
• Max. permissible deviation Wide ±5.0 kHz
Middle – ±4.0 kHz
Narrow ±2.5 kHz
• Frequency error ±2.5 ppm ±1.5 kHz
• Spurious emission 70 dB min. 0.25 µW (≤1 GHz), 1.0 µW (>1 GHz)
TRANSMITTER
1-1
[USA], [EXP] [EUR]
• Receive system Double-conversion superheterodyne
• Intermediate frequencies 1st IF; 46.35 MHz, 2nd IF; 450 kHz
• Sensitivity 0.25 μV typ. at 12 dB SINAD −4 dBμV (EMF) typ. at 20 dB SINAD
• Squelch sensitivity (At threshold) 0.25 μV typ. −4 dBμV (EMF) typ.
• Adjacent channel Wide More than 70 dB (75 dB typ.)
selectivity Middle − More than 70 dB (75 dB typ.)
Narrow More than 60 dB (65 dB typ.)
RECEIVER
1-2
SECTION 2. INSIDE VIEWS
• FRONT UNIT
CPU
(IC1)
CLOCK FREQUENCY
SHIFT DIODE
(D6)
CPU CLOCK
(X1)
RESET IC
(IC2)
EEPROM
(IC3)
KEY BACKLIGHT SW
(Q2)
TONE FILTER
(IC5)
2-1
• MAIN-A UNIT
(TOP VIEW)
RIPPLE FILTER
(Q17)
R8 LINE REGULATOR VCO SWITCH
(Q30) (Q15)
PLL IC
(IC4)
1ST IF FILTER
(FI1)
APC AMP
(IC2) IF DEMODULATOR IC
(IC1)
AF AMP
2ND IF FILTER (IC21)
BANDWIDTH SWITCH
(Q40)
TONE FILETR
(Q39)
2-2
• MAIN-A UNIT
(BOTTOM VIEW)
+5V LINE REGULATOR T8 LINE REGULATOR
(Q27) (Q25)
AF MUTE SW
(Q35)
MODULATION LINE SW
(Q31)
VCO
DRIVE AMP
REFERENCE OSCILLATOR (Q9)
MODULATION BUFFER
(IC19)
REFERENCE FREQUENCY
OSCILLATOR (X2)
D/A CONVERTER
(IC20) 1ST MIXER
(Q3)
2ND IF FILTER
(For wide mode)
EXPANDER (FI2)
(IC17)
2ND IF FILTER
(For narrow mode)
D/A CONVERTER (FI6)
(IC18) RF AMP
(Q2)
AF LINE SW
(IC14)
AF AMP
(IC15)
AF/TONE FILTER
(IC16)
2-3
SECTION 3. DISASSEMBLY INSTRUCTION
1) Remove 4 screws from the bottom cover, and then 5) Unsolder total of 9 points; 3 points at the antenna
remove it. connector, 6 points at the PA module.
2) Disconnect the flat cable and speaker cable.
3) Remove 2 screws from the both sides, and then remove
UNSOLDER
the front panel in the direction of the arrow.
SCREW×4
BOTTOM COVER Solder
remover
PCB
FLAT
CABLE
PCB
FRONT PANEL
SPEAKER
SCREW×2 CABLE
PCB
3-1
SECTION 4 OPTIONAL PRODUCTS INSTALLATION
OPC-1939/OPC-2078
DISC MIC
NOTE: Be sure to recover the patterns when you remove the optional product. Otherwise no TX modulation or AF output is available.
Solder
remover
4-1
SECTION 5. CIRCUIT DESCRIPTION
The applied RX signal is passed through the 2-staged tuned The 15.3 MHz signal generated by the reference oscillator
BPF (D4, D8) to remove unwanted out-of-band signals, and (X2) is passed through the filter AMP (Q34, L33, 35, C305–
amplified by the low-noise RF AMP (Q2), and then applied 308) to extract the 45.9 MHz 3rd harmonic component.
to the 1st mixer (Q3) through another 2-staged tuned BPF The 45.9 MHz signal is then applied to the pin 2 of IF
(D9, 10). demodulator IC (IC1) as the 2nd LO signal.
Total of 4 stage BPFs are tuned to the RX frequency by the The converted 2nd IF signal is output from the pin 3 of IF
tuning voltage “T1” and “T2” from the D/A converter (IC20), demodulator IC (IC1), and filtered by the ceramic filters
to obtain required IMD characteristic. (FI2 and FI6 for Narrow mode; FI2 only for Wide mode) to
remove unwanted out-of-band signals, and then applied to
• RF CIRCUITS the internal frequency-demodulator of IF demodulator IC
136-174 MHz
(IC1) from pin 5.
D2,D3,D5,
D6,D47,D48 D1,D11,D12
The demodulator is a quadrature type which uses X1 as the
From the TX AMP ANT
LP F PWR LPF
phase shifter.
SW DET
15.3MHz
Tuning voltage “T2” Tuning voltage “T1”
X3 Q34 IC1
45.9MHz
IF IC
BPF
1ST IF CIRCUITS (MAIN-A UNIT)
The RX signal from the BPF is mixed with the 1st LO signal D66,D67 FI2
Q5
to be converted into the 46.35 MHz 1st IF signal. D/A
SQIN
W/N
NWC X1 W/N
SW
CERAMIC
BPF
IC18 DISC SW
AK2330
FI6
The 1st LO signal is generated by the RX VCO (Q14, D33, 450kHz
CERAMIC W/N
D34, L26, L39, etc.), and passed through the LO SW (D15) To the AF circuits
BPF SW
and attenuator, and then applied to the 1st mixer (Q3) NWC Q40 D64,D65
• 1ST IF CIRCUITS
1st LO signals D15
(182.35 MHz-220.35 MHz) LO
SW
LPF
FI1
Q4 Q3
To IF IC IF XTAL 46.35 MHz From RF circuits
AMP BPF
1st mixer
5-1
AF CIRCUITS (MAIN-A UNIT) SIGNALING (DECODING) (MAIN-A UNIT)
The demodulated AF signal from the IF demodulator IC (IC1) Demodulated signal from the pin 9 of the IF demodulator
is amplified by the AMP (IC21), filtered by the HPF (IC16), IC (IC1) is passed through the LPF to extract tone signals
and then passed through the AF line SW (IC14) and LPF contained in the demodulated signal.
(IC16). The filtered AF signal is adjusted in level (=loudness)
by the D/A converter (IC18), and applied to the AF AMP 2/5 tone signal is extracted by the LPF (IC16). CTCSS/
(IC15) through the AF line SW (IC14). DTCS signals are extracted by the LPF (Q39).
The amplified AF signal is applied to the AF power AMP (IC8) These extracted tone signal is applied to the CPU (FRONT
and power-amplified to obtain AF output level. UNIT: IC1) for decoding.
• RX AF CIRCUITS
IC16 IC16
IC14
IC21
DISC RXAF LPF
From the IF IC AMP HPF
ANALOG
SW IC15 IC8
AF J4
VRAF TMONI AF
AMP POWER
D/A AMP Ext. speaker jack
IC18
AF
AF ON MUTE
Q35,36,D29
IC16
DISC LPF
CDEC
(TCSS/DTCS signals)
5-2
5-2 TRANSMITTER CIRCUITS
MIC AMPLIFIER (FRONT UNIT) CTCSS/DTCS SIGNALS ENCODING (FRONT UNIT)
Audio signal from the connected microphone is applied to The CTCSS/DTCS encoding signal from the CPU (IC1)
the MIC AMP (IC5), through the microphone connector (J1). “CENC0–CENC2” is passed through the LPF (IC5) for
The amplified MIC signal is applied to the MAIN UNIT. waveform conversion, and applied to the MAIN UNIT as tone
modulation signal.
• TX AF CIRCUITS
To the Reference
frequency oscillator
TX AMPLIFIERS (MAIN-A UNIT)
MIC
The frequency-modulated signal from the TX VCO is buffer-
MCOT
D/A
amplified by two buffers (Q11 and Q10), and applied to the
IC16
IC16 TONE drive AMP (Q9) as the TX signal through the LO SW (D14).
MCGO MIC SPIN
Splat.
IC18 AMP
line CDTS The amplified TX signal is applied to the FET HPA module
BAL SW
(IC3) through the LPF, and power-amplified to obtain TX
IC14
CD4066
output power level.
VRAF MOD
TX VCO J1
IC5
MIC
MODI AMP
MICROPHONE
CONNECTOR
The power-amplified TX signal is passed through the
antenna SW (D3) and LPF as a harmonic filter, and then fed
FRONT UNIT to the antenna.
• MODULATION CIRCUITS
X2 IC4 Q11 Q10 D14,D15
IC19 CR-794 MB15A02
BAL TX/RX To TX AMPs
REF REF BUFF BUFF
PLL LOOP LV SW
AMP
OSC IC FIL
D18 TX VCO
FM
MOD
5-3
5-3 FREQUENCY SYNTHSIZER CIRCUITS
VCOs (MAIN-A UNIT) PLL (MAIN-A UNIT)
The TX VCO which generates the TX signal is composed The applied VCO output is divided according to the serial
by Q13, D16, D31, L25, L38, etc., and the frequency data including divide ratio from the CPU, at the prescaler
modulation is carried out by applying modulation signals to and programmable divider. In the same way, the reference
D18. frequency signal from the reference frequency signal
oscillator is applied to the PLL IC and divide so that these
The RX VCO which generates the 1st LO signals is are the same frequency.
composed by Q14, D33, D34, L26, L39, etc.
The frequency-matched signal is applied to the phase
These two VCOs are switched by the VCO SW (Q15, 16) comparator and phase-compared. The resulted phase
using “RXC” signal. difference is detected as a phase-type signal, and level-
adjusted at the charge pump then output. The output pulse
The output signal from each VCO is amplified by the buffer type signal is passed through the loop filter to be converted
AMP (Q11) and LO AMP (Q10), and then applied to the TX into the DC voltage (=Lock Voltage).
or RX circuits.
Applying the lock voltage to the variable capacitors
A portion of generated signals is applied to the PLL IC (IC4) (VD) which composes a part of the resonator of VCO,
via buffer AMP (Q12). the capacitance of VDs changes corresponding to the
applied lock voltage. This causes the change of resonation
frequency that determines the VCO oscillating frequency to
keep the VCO frequency constant.
Q17 Q15,16
D52 TXC
Q14,D33,34
RLVA RLV
ADJ Q11 Q10 D14,D15
IC19 X2 IC4 RX VCO
LO
REF 15.3MHz BUFF BUFF 136/146 MHz-1740 MHz
REF PLL LOOP LV LV SW
AMP
IC FIL
D53
Q13,D16,31
T8V TLVA TLV
ADJ
TX VCO
LPF 182.35 MHz-220.35 MHz
Q34 Clock,Data,Strobe Q12
X3 LPF BPF X2
D18
D54,55
FM
MOD
IC1
BPF 45.9MHz IF IC
Q26,Q30 Q23,Q24
RXC HV
R8V R8 POWER Power supply cable
RF AMP(Q2), 1st IF AMP(Q4), 1st mixer(Q3), etc.
REG 8V SW
VCC W2
External output(from J6)
HV
HPA module(IC3)
5-4
5-5 PORT ALLOCATIONS
• CPU (FRONT UNIT; IC1)
Pin Port Pin Port
Description I/O Description I/O
No. Name No. Name
KR1− Serial clock signal to the PLL IC (IC4, pin 9)
1−3 Dealer-programmable keys input. I
KR3 98 SCK and D/A converters (IC17, pin 3/IC18, pin 8/ O
10 CCS Chip-select signal to the attached optional unit. O IC20, pin 7).
19− CENC0− Serial data to the PLL IC (IC4, pin 9) and D/A
CTCSS/DTCS signal. O 99 SO O
21 CENC2 converters (IC17, pin 3/IC18, pin 8/IC20, pin 7).
Frequency response of tone filter (IC5) 100 KR0 Input ports for dealer-programmable keys. I
23 DUSE switching control. O
“Low”=While transmitting.
PTT input.
24 IPTT I • EXPANDER (MAIN UNIT; IC17)
“Low”=PTT is pushed.
Microphone on/off hook detect. Pin Line
25 HANG I Description
“Low”=The microphone is off hook. No. Name
30 PLST PLL strobe to the PLL IC (MAIN UNIT; IC4, pin 11). O 4 RXC T8V, R8V lines and RX VCO ON/OFF control.
PLL unlock detect signal from the PLL IC AF mute SW (Q35) control.
34 ULCK (MAIN UNIT; IC4, pin 7). I 5 AFON
“Low”=Mute
“Low”=While the PLL circuit is unlocked.
• RX band width switching signal to the 2nd IF
Key indicator LED for [P1] (DS9) control. filter SW (D56, D57).
35 LED1 O
“High”= Lights. “Low”=Narrow mode
Key indicator LED for [P2] (DS8) control. 6 NWC
36 LED2 O • RX band width switching signal to the phase
“High”= Lights. shifter SW (Q5).
Key indicator LED for [P3] (DS7) control. “Low”=Wide mode
37 LED3 O
“High”= Lights. AF mute signal to the analog switch (IC3,
[PWR] key input. 7 RMUT pins 12, 13).
28 POSW I
“Low”=Pushed. “Low”=While the squelch is close or transmitting.
Serial data to the D/A converter (MAIN UNIT; External device control.
39 DSDA O
IC20, pin 6). 12 HORNO “Low”=Pin 6 of OPC-1939 or pin 10 of OPC-
43 SENC DTMF signals to the LPF (IC5, pin 3). O 2078 (if connected) is “Low.”
44 BEEP Beep audio. O Transmit mute signal to the transmit mute switch
45 SDEC DTMF signals. I 13 TMUT (Q46).
“High”=Transmitting is muted.
46 CDEC CTCSS/DTCS signals. I
48 BATV Power supply voltage. I
49 LVIN VCO lock voltage. I
50 RSSI
Received signal strength level signal from the IF
I
• D/A CONVERTER (MAIN UNIT; IC18)
demodulator IC (MAIN UNIT; IC1, pin 12).
Pin
51 TEMP Temperature sensing voltage. I Description
No.
[VOL] dial (R14) input. (divided voltage of “5V” 2, 3 MIC signal level adjustment.
52 AFVI I
line)
4, 5 RX AF/MIC signal level adjustment.
CPU reset signal from the reset IC (IC8, pin 1).
59 RES I 16, 17 Tone signal level adjustment.
“Low”=CPU is reset.
CPU clock shift signal to the clock frequency Oscillation frequency control voltage to the reference
69 CSFT O 18, 19
shift switch (D6). frequency oscillator (X2).
Strobe signal to the D/A converter (MAIN 20, 21 Modulation signal level adjustment.
71 DAST O
UNIT; IC18, pin 7). 22, 23 Beep sound loudness adjustment.
72 IGSW Ignition SW input. I 24, 25 Squelch threshold level adjustment.
Noise signal from the IF demodulate IC (MAIN
75 NOIS I
UNIT; IC1, pin 13).
82 ESDA Serial data to the EEPROM (IC3, pin 5). O
85 ESCL Clock signal to the EEPROM (IC3, pin 6). O • D/A CONVERTER (MAIN UNIT; IC20)
Transceiver's power control. Pin Line
86 PWON I Description
“High”=Power ON. No. Name
Channel indicator LED for [CH4] (DS3) control. • While receiving
87 CH4L O
“High”= Lights. Tuning voltage to the tuned BPF (D4, D8).
Channel indicator LED for [CH3] (DS4) control. 1 T1 • While transmitting
88 CH3L O TX power level setting signal to the APC AMP
“High”= Lights.
IC2).
Channel indicator LED for [CH2] (DS5) control.
89 CH2L O 2 T2 Tuning voltage to the tuned BPF (D9, D10).
“High”= Lights.
Channel indicator LED for [CH1] (DS6) control. Oscillation frequency correcting voltage to the TX
90 CH1L O 3 TLVA
VCO (Q13, D16, D18, D31, D53).
“High”= Lights.
Key backlight LED (DS1, DS2) control. Oscillation frequency correcting voltage to the RX
95 LIGT2 O 4 RLVA
VCO (Q14, D33, D34, D52).
“High”=Backlight is ON.
TX indicator LED (DS10) control.
96 TLED O
“High”= Lights red (While transmitting).
RX indicator LED (DS10) control.
97 RLED O
“High”= Lights green (While receiving).
5-5
SECTION 6. ADJUSTMENT PROCEDURE
6-1 PREPARATION
M REQUIRED EQUIPMENTS
EQUIPMENT GRADE AND RANGE EQUIPMENT GRADE AND RANGE
Modified OPC-1122U
Cloning Software CS-F5010 : Revision 1.0 or later JIG Cable
(see the illust below)
Output voltage : 13.6 V DC except [EUR] Power attenuation : 50 or 60 dB
DC Power Supply 13.2 V DC [EUR] Attenuator Capacity : 30 W [25 W ver.]
Current capacity : More than 20 A 60 W [50 W ver.]
Modulation Frequency range : DC–300 MHz Input impedance :4Ω
External Speaker
Analyzer Measuring range : 0 to ±10 kHz Capacity : 20 W or more
Frequency range : 0.1–300 MHz Frequency range : 0.1–300 MHz
Standard Signal
Frequency Counter Frequency accuracy : ±1 ppm or better Output level : 0.1 µV to 32 mV
Generator (SSG)
Sensitivity : 100 mV or better (–127 to –17 dBm)
Measuring range : 0.1–30 W [25 W ver.]
0.1–60 W [50 W ver.]
Frequency rang : DC–20 MHz
RF Power Meter Frequency range : 100–300 MHz Oscilloscope
Measuring range : 0.01–20 V
Impedance : 50 Ω
SWR : Better than 1.2 : 1
M JIG CABLE
OPC-1122U
EXT. SPEAKER
(5 W/4 Ω)
PTT SWITCH
6-1
M ADJUSTMENT FREQUENCIES
Before starting adjustment, clone adjustment frequencies and settings into the transceiver as below.
CONVENIENT: The cloning data file for the adjustment, as described in this service manual, is attached.
Right click the clip icon, and select “Save Embeded File to Disk.”
NOTE: FOR [EUR] versions, when adjust “Deviation,” “Modulation Balance,” and
“S-meter” in the middle band, change the bandwidth to “Middle” as below.
Select “Middle”
6-2
M CONNECTION
Oscilloscope
PC
to USB port
to the MIC
connector
JIG CABLE
AC millivoltmeter
Audio generator
ADJ. CHANNEL
TX POWER
MOD. BALANCE
DEVIATION
CTCSS\DTCS
SQUELCH
REF. FREQUENCY
RX SENSITIVITY
LOCK VOLTAGE
RSSI
(S3 and S1 level)
6-3
6-2 FREQUENCY ADJUSTMENT
1) Select an adjustment item using cursor or [↑]/[↓] of the PC’s keyboard.
2) Set or modify the adjustment value as specified using [←]/[→] of the PC’s keyboard, then push [ENTER].
TRANSCEIVER’S ADJUSTMENT
ADJUSTMENT OPERATION VALUE
CONDITION ITEM
PLL LOCK 1 • Channel : 1-1 1) Connect an RF power meter to the an- 1.1 V
VOLTAGE • Receiving tenna connector. [RX LVA]
(RX) 2) Set the adjustment value on the “Adjust
Utility” screen.
(TX) 2 • Channel : 1-2 1.06 V
[TX LVA]
• Transmitting
(RX) 3 • Channel : 1-3 • Click [Update (F5)] button, and then check 3.0–4.0 V
• Receiving the “LVIN” item on the “I/O Check screen” [LVIN] (Verify)
as below. (On the “I/O
(TX) 4 • Channel : 1-3 Check screen”) 2.5–3.5 V
• Transmitting (Verify)
REFERENCE 1 • Channel : 1-4 • Loosely couple a frequency counter to the 174.000000 MHz
[REF]
FREQUENCY • Transmitting antenna connector.
Lock voltage
6-4
6-3 TRANSMIT ADJUSTMENT
1) Select an adjustment item using cursor or [↑]/[↓] of the PC’s keyboard.
2) Set or modify the adjustment value as specified using [←]/[→] of the PC’s keyboard, then push [ENTER].
TRANSCEIVER’S ADJUSTMENT
ADJUSTMENT OPERATION VALUE
CONDITION ITEM
OUTPUT 1 • Channel : 1-5 • Connect an RF power meter to the an- 25 W [25 W ver.]
POWER • Transmitting tenna connector. [Power (Hi)] 50 W [50 W ver.]
(Hi power)
(L2 power) 2 • Channel : 1-6 10 W [25 W ver.]
[Power (L2)]
• Transmitting 25 W [50 W ver.]
(L1 power) 3 • Channel : 1-7 2.5 W [25 W ver.]
[Power (L1)]
• Transmitting 5.0 W [50 W ver.]
MODULATION 1 • Channel : 1-8 • Connect a modulation analyzer with an As flat as possible.
BALANCE • No audio signal applied oscilloscope to the antenna connector
to the JIG cable. through an attenuator, and set it as;
• Transmitting. HPF : OFF
[BAL]
LPF : 20 kHz
De-emphasis : OFF
Detector : (P–P)/2
No over or under shoot.
DEVIATION 1 • Channel : 1-9 • Connect a modulation analyzer to ±2.05 to ±2.15 kHz
(NARROW) • Transmitting the antenna connector through an [MOD N]
attenuator, and set it as described in
the “MODULATION BALANCE” above.
(WIDE) 2 • Channel : 1-10
• Connect an audio generator to the JIG ±4.05 to ±4.15 kHz
[MOD Ratio]
• Transmitting
cable and set it as;
(MIDDLE)* 3 • Channel : 1-11 Frequency : 1.0 kHz ±3.25 to ±3.35 kHz
[MOD Ratio]
• Transmitting Level : 40 mVrms
CTCSS/DTCS 1 • Channel : 1-12 • Connect a modulation analyzer to ±0.65 to ±0.75 kHz
DEVIATION • No audio signal applied the antenna connector through an
to the JIG cable. attenuator, and set it as described in [CTCSS/DTCS]
• Transmitting the “MODULATION BALANCE” above.
*: [EUR] only
6-5
6-4 RECEIVE ADJUSTMENT
1) Select an adjustment item using cursor or [↑]/[↓] of the PC’s keyboard.
2) Set or modify the adjustment value as specified using [←]/[→] of the PC’s keyboard, then push [ENTER].
TRANSCEIVER’S ADJUSTMENT
ADJUSTMENT OPERATION VALUE
CONDITION ITEM
RECEIVE NOTE: When “RECEIVE SENSITIVITY” is re-adjusted, “S-METER” and “SQUELCH” must be re-adjusted too.
SENSITIVITY 1
• Channel : 1-13 1) Connect an SSG to the antenna connec- Push [ENTER].
• Receiving tor and set it as;
Frequency : 136.000 MHz
Level† : +20 dBµ (–87 dBm)
[BPF ALL]
Modulation : 1 kHz
Deviation : ±3.0 kHz
2) Put the cursor on the adjustment item,
then push [ENTER].
S-METER NOTE: "RECEIVE SENSITIVITY" MUST be adjusted before "S-METER." When "RECEIVE SENSITIVITY" is
(S3 level) re-adjusted, "S-METER" MUST be re-adjusted too.
1 • Channel : 1-14 • Connect an SSG to the antenna connec- Push [ENTER].
• Receiving tor and set it as;
Frequency : 136.000 MHz
Level† : +23 dBµ (–84 dBm)
Modulation : 1 kHz [RSSI]
Deviation : ±3.0 kHz
(S1 level) 2 • Set the SSG as;
Level† : –7 dBµ (–114 dBm)
SQUELCH NOTE: "RECEIVE SENSITIVITY" MUST be adjusted before "SQUELCH." When "RECEIVE SENSITIVITY" is
re-adjusted, "SQUELCH" MUST be re-adjusted too.
1 • Channel : 1-15 1) Connect a SSG to the antenna connec- Push [ENTER].
• Receiving tor and set it as;
Frequency : 136.000 MHz
Level† : –13 dBµ (–120 dBm)
Modulation : 1 kHz [SQL]
Deviation : ±3.0 kHz
2) Once close the squelch by increasing [SQL]
value, and then decrease the value to open
the squelch.
†
; The output level of the standard signal generator (SSG) is indicated as the SSG’s open circuit.
6-6
SECTION 7. PARTS LIST
M.=Mounted side (T: Mounted on the Top side, B: Mounted on the Bottom side)
S.=Surface mount
7-6
SECTION 8. MECHANICAL PARTS
[FRONT UNIT]
MP6 MP8 MP4 (M5×12)
REF ORDER
DESCRIPTION QTY.
NO. NO.
J1 6450002210 3017-8821 <KIN> 1
J2* 6510027960 04-6294-040-000-800 1
J3* 6510022022 14FLT-SM2-TB (LF) (SN) (M) 1 MP7 MP3 MP5 (M5×20)
SP1 2510001221 C052SB500-14 <OSC> 1
MP1 (C)
[25 W version]
J1 (C)
W2 (M)
MP2 (M)
MP11 (C)
J4 (M)
MAIN-A UNIT
R14 (F)
W1 (F)
MP3 (C)×8
J1 (F)
MP2 (F)
MP7 (F)×2
W1 (C)
MP5 (F)
SP1 (F)
MP7 (C)×4
MP9 (F)
8-2
The combination of top side and bottom side of this
EP4 EP5
• MAIN-A UNIT 6 2
(TOP VIEW)
V70
7 W1 C83 C471
C87
C364
C372
C342
W1
V65
C82
C401 R338 EP4
R337
R333
C86
R334
C362
HV
R332
C84
C85
R212
R213
V60
BLK RED
EP5
L5
C107
C462
D3
L5
IC2 W2 W2
GND
D3
D5
V55
C411
C443
C79
C12
C9
D5
C76
R56
R58
C81
IC2
C451
C330
R48
R53
D48 R49
D28
R52
R59
C80
R51
C473
D47 L4 R55
C72
C77
V50
IC9
C73
C88
Q20
C484
Q20 R199
C388
R200
C472
-T8V 1
8 L4 5 MP4
R201
C270
V45
C271
C266
-T1 Q26 Q24 Q23
Q1 R205
R204
VCC
D63
C477
V40
C479 C480
R32
C51
C262
Q1 Q30
FI1
C476
C474
Q16 R392 8V
C267
Q30 Q23
C363
R319
C478
R378
C263
R317 C275
D62
C111
IC10
Q16 R316
R320
C383
-R8V
R350
C31
PLL
IC10
V35
FI1
C264
C163
Q15
C357
Q15
C268
D65
C314
R98
S1
R352
VHF
D37
C152
C153
C154
C151
R103
C155
Q40
C23
R93
C385 Q17
Q40
R353
D64
1 SP+
C394
SIMPLE TYPE
D66
Q17
L54
C337
R401
C148
R354
J7
V30
IC4
C180
D67
R211
2 SP−
R112
R111
R113
C175
C395
B7425A
C101
C384
R33
C59
Q33 J6 1
C486
C71
IC4
C396
C140
C398
R351
R97
EP8
-VREF VRAF J7
C58
R34
R35
C463
Q43
Q33
R96 R95 C293
-TENC C70
UT-109R T2
R135
R290
C60
-SO R42 R45 R44 VCC
SP1 (FRONT UNIT)
V25
R238
C75
Q4
R89
C68 C69
UT-110R -SCK IC1 Ext.I/O6 R355
L47
Q18
R122
R130
R183
R133
R391
C347
Q4 (DIM/IGSW) R198
R46
C147
C149
R119
C170
R363
C141
R100
R101
C143
C189
R400
C482
C66
SDEC R43 I
EP9
R251
R250
-SPAF TONE
R118 R396 C490 R397
R 2 54 R 25 5 R2 5 6 C348
RSSI- C198 Ext.I/O 7
C135
-BAL C62 CP1
C274
C492
R134 R186
Q39
L46
R253 R249 R248 C488 R399 R38 K (AFO)
R218
C242
R377
B RLVA
R37
C173
-MCGO
R349
R285
C321 C320 R398 -UNLK
R41
R252 C322
IC21 TLVA
R247
C64
D C65
J6
R336
DISC C196
Q37 Ext.I/O 7
C489
C290
Q39 C195 (AFO)
R325
R143
C63
R129
R137
Q5 Q5 Q37 C288
DISC
V15
R145
R210
C200
R209
C142
TXC- J2 R142 R348
Q19 C289
PGIO2
5V
CDEC
DSDA
TONE
UNLK
TENC
SDEC
EXOE
BATV
CPU5
OPV1
R358 C291 IN
TEMP
EXST
PLST
R144
NOIS
RSSI
LVIN
GND
R291 C350
AFO
4
R261
R262
R263
R372
A L10 -CPU5V
Q19
1
5V
R271
R373 R374
PTTO
DAST
BUSY
OPT3
OPT2
EXST (OPV3)
MCIN
SIGO
OPT1
GND
GND
PTTI
NC
NC
NC
NC
NC
C295 C294
(OPV2)
20
PWON
J2 14(EPTT)
PGIO4
R315
BEEP
C
OPT2
OPT1
EPTT
PTT
C481
SCK
GND
Ext.I/O
R359
R314 D61 4 (SERIAL)
J1 J1 CDEC-
R327 1 F Ext.I/O
DIM
8V
PTTO
OPT3
PTTI
DAST
MIC
PGIO3
CIRQ
SI
SO
CCS
C436
AFOUT
C201 10(SERIAL)
R361
D59
R147
R357
DISC
R313
-DIM 13
R148
R149
R146
R150
-HORNO
V5
40 21
GND
NC
NC
CCS
SCK
NC
AFONO
CIRQ
MMUTE
SO
SI
NC
5V
8V
GND
BEPO
REM
RMUT
BUSY -PWON G
CP28 REM -EPTT
-AFON
MCIN -MCIN
V0
H0 H5 H10 H15 H20 H25 H30 H35 H40 H45 H50 H55 H60 H65 H70 H75 H80 H85 H90 H95 H100 H105 H110 H115 H120 H125 H130
[VOL]
• FRONT UNIT
V30
C128
C129
R18
R76
D2
D1
V15
V10
DS2
DS1
V5
J1
V0
H0 H5 H10 H15 H20 H25 H30 H35 H40 H45 H50 H55 H60 H65 H70 H75 H80 H85 H90 H95
[MICROPHONE CONNECTOR]
9-1
The combination of top side and bottom side of this
• MAIN-A UNIT
(BOTTOM VIEW)
J4
V70
C470
C467
C468
C402
C368
C369
C469
C1
V65
C403
C375
FI5
L16
R1
C8
L16
L1
L3 L1
C466
C366
C377
FI4
V60
C465 C456
C431
C380 L43 L23
C371
C260
C404
C7
C259
R9
C4
L3 C2
D12
FI3 C381 C460 R387 C458
C408
R10
D22
C367
C14
C459
C78
D12
L2
C461 C6
V55
R54
R388 C3
Q9
C74
C10
R57
C5
C258 Q9
D1
R386 R5
R4
C94
R7
C258
C93 R385 C409 L6 D1 L2
Q25 C457 -T8V R8
C13
C15
V50
C261
C442
D11
L6
R393
R8 R6
C11
C106 R67 R68 C108
R202
C269
C99 C17
R203
Q25 D11
D6
C19
V45
R329 L31 C18
C440
C272 Q29 D23 C265
R23
R21
C37
C35
C45
C39
C53
C54
C265
D14
C276
Q29 D9 C36
C333
L13
R300
C391
C390
R301
C32
R16
C33
C34
L11
V40
R26
R27
R29
C50
C48
R30
C52
R31
C339
C44
C26
C20
C25
R17
L7
L9
R12 R13
R20
Q2
R299
L36
R15
Q3
Q3
L8
R11
R235
C29
D4
D8
R50
L11
C256
R390
R302
C43
R69
C30 C22
L7
C57
R22
C46 R19
C303
R70 R8V C27
C110
C109
R310
C38
L8
V35
C139 C28 R14
L21
R73 R234 C100
C256
C42
EP1
C255
L22
R74 C102 R71
Q10
C122
R76 C284 T2-
R311
C335
Q13
Q11
C103
C120 R78 C297 L44 L32
-T1
D55
D54
R75
R345
C399
C119 C118
C301
B7425A
C158
C300
C298
C299
L45
C104 Q12 C159 R341 R342 C397
FI2
L41
R328
C121
C131 R83
V30
C285 C161 C156
R84
C282
C283
R215
C185
C190
C105 C286
FI6 C174
C123
D53
C255 W/N
L25
X1 NARROW
C113
C114
R80
R85
C129
C133
MP1
IC18
C360 R339
C165
C323 R36
C124
R394
L26 C160 IC20
IC16
R86
Q14 IC18
V25
C376
Q27
C126
R79
Q34
D18
C308
C306
R40
R241
R242
C316
R244
R245
C318
C317
EP7 C157
L53
X1
L35
D31
Q28 X2 R340
L33
C115
C116
C117
C134
C305
C307
C67
C356 C127 C354 R237 R121 R115
R123
C315
R240
R243
C273
R120
X2 R368
C145
Q28
R39
R156
C355 R221
IC20 C188
C312
D34 D33
IC16
R125
D16 D52 R236 C169 C167
Q27
C247
R371
R105 R110 R104
V20
-REF 5V R330
R287
C292
L38
L27
L28
L39
C182
R126
R384
R127
C184
C244
R184 C177
D29
C178
C164 R220 C181
-RLVA
C246
R185 R370
C351
Q36 C138 C144
IC19
NWC -MOD
C359
R124
C183
R128
IC19
Q35 R195
SDEC C349 R187
C179
IC14
R196 R159
C251 C252 5V TLVA TONE R188
C253
R197 Q36 C162
-DISC IC14
Q35
V15
R228
R224
R117
MCOT
C378
C209
C210
C208
R375
R229 C287
CPU5V- IC17 -OPV1
C186
Q31
R226 R225
R326
R138
5V
D26 LVIN CDEC
C203
C207 R139
R223
V10
C379
D58
R298
IC17
R381
R297
R304 C245
C437
MCIN-
R193
C249
C382
R360
R270
R269
D60
R192
R191
C491
D42 D42 D43 C187
C226
C204
RXC DIM- IC15
C361
R362
EPTT D44 R194
C250
C310
TXC AFOUT
V5
D43 IC15
AFO AFON
V0
H130 H125 H120 H115 H110 H105 H100 H95 H90 H85 H80 H75 H70 H65 H60 H55 H50 H45 H40 H35 H30 H25 H20 H15 H10 H5 H0
IC2
R115
R107
V30
R111
R112
C124
(BOTTOM VIEW)
Q9
RES C107
B7424A
Q6
R65
J3 R136 C111 IC3 R135 C25 C41
R20 Q8
0 12 3 R137 R68 R45 C84 R41
C36
R21 R116 Q7 R58 R25 C14 C17 C76 R42 C27 C26
R22 KR
V25
R23 C15 R27 R43 R44 R40
PWON OPT1 LIGHT2 R29 R24 R26
R138
C112 LED2
R33 C23
CPU5V AFVI
R134
R131
C131 R32 R39 IC5
R133
V20
R117
R130
Q14
R34 R38
C8
PLST R109 R102
R129
R104 R101
R48
C22
C28
C24
R140
UNLK
V15
R12 R11 C87
C104
R113 C101
SDEC CLI MIC PTT CLO
Q10
C106 C126
Q1
CLI
R106
R120
R105
R114
C118
C120
C119
C117
C116
C114
C93
C30
C113
Q12
C77
R132 R46 D5 GND MICE AFO 8V
R19
R16
D3
NOISCDEC C31 R47 R51
C34
C38
R77
C4
V10
PGIO2
C3
DSDA
TONE
TEMP
SDEC
UNLK
EXOE
L2
BATV
CDEC
OPV1
TENC
EXST
PLST
NOIS
RSSI
G ND
LVIN
C54
C50
C10
C12
R139
5V
C130
CLO AFO
CPU5
MIC
AFO
8V
C125
R60
J2
V5
8V
R127
POSW
R90
C2
C5
PGIO4
PWON
OPT1
SCK
CIRQ
SO
GND
DIM
SI
EPTT
PTTO
MIC
PGIO3
BEEP
CCS
OPT2
PTTI
DAST
OPT3
BEEP
C69
C74
DIM
V0
H95 H90 H85 H80 H75 H70 H65 H60 H55 H50 H45 H40 H35 H30 H25 H20 H15 H10 H5 H0
9-2
SECTION 10. BLOCK DIAGRAM
Q17
Q15:XP1214
2SC4116
Q16:LDTC144EE 136-174MHz
TLVA TLV
SCK T8V AD J TX VCO 182.35MHz-220.35MHz
Q34 SO D54,55 Q13:2SC4226 Q12 IC2
2SC4116 PLST HVD144A D16:HVC376B 2SC5006 Q1:2SK1829 TA75S01F D1,D11,D12:LRB706F
D31:HVC376B
RSSI AGC APC DET
X3 LPF BPF X2 LPF
AMP PWR
D18
FM HVL355CM
MOD Q4 FI1 D9-B D9-A Q2 D4 D8
2SC5107 FL-442 Q3 HVC350B HVC350B HVC375B HVC375B D 28:MA2S728
3SK293
45.9MHz 46.35MHz 3SK293
BPF IF IC IF XTAL
BPF BPF
RF
BPF BPF MUT E TMUT
AMP BPF AMP SW
IC1:NJM2591V
F
D66,D67 FI2
Q5 HVD144A LTM450FW T2 T1
LDTC144EE
NWC W/N CERAMIC
X1
W/N SW BPF
SW
FI6 450kHz RSSI NOIS IC15 IC8
JTBM450CX70 LTM450GW TA75S01F LA4425A
J4
IC21 CERAMIC PRE AF
SQIN DISC W/N BEEP
TA75S01F
BPF SW D64,D65:HVD144A BEEPO AMP AM P
Q40:LDTA114EE D 29:L1SS400
AM P
REF 5V 450kHz MCOT M CIN Q36:LDTC144EE
NWC Q35:DTC363EK AFO
CP4
A
CP_3
AF
CP4
MCOT AFON
IC16
CP4 MUT E G
NJM12902
CP_3 I
(EAFO)
MCGO AM P
J6 K
Ext.I/O_7_(AFO) PGIO4
IC18 NJM12902 SW
AK2330 DISC CP3 Ext.I/O_11_(HORN) CP4
SO RXAF TXC Q31
D IC5 J1
HPF
SCK ACC DISC 2SJ144 NJM12902 AFO
DAST B MMUT CP3
F F
CP_3
CP_3
CP3
RMUT AFVI
C AF VR
MMUT E PTTO PTTO
R14
RK09D1130A1N
10 - 1
SECTION 11. VOLTAGE DIAGRAM
• FRONT UNIT
Q14
R130 DS10 LDTC114EE
390 CL-165HR/YG RLED 12.29MHz
YG 2.54Vp-p
X1 4.97V
Q13 C104
CR-915
R131 LDTC114EE R101 22P
HR CPU5V RES
1.8K TLED 12K
HVD142A
IC2 R107
C101
C105
C106
0.1
NJU7704F3-42A
15P
R103
10K
100K
R113
100K
8P
12K
R102 D6
R5 R51
R106 1 5
CD VDD
1M 2
0.027
C102 VSS
Q12
C107
3 4
12K
R132 0.1 MR VOUT
LDTC114EE
1.8K
R105
LED1 CSFT
DS9 C103
10
LNJ426W83RA 0.1
Q11 MD2
R133 LDTC114EE R140
HANG
C111
C113
1.8K 10K
0.1
4.7
C112
LED2 DAST (OPV3) R118 R119
DS8 1K 1K
47
DIM (IGSW/DIM)
R104
100K
LNJ426W83RA PTTI
Q10 PTTO AFVI
R134
LDTC114EE NOIS R117 TEMP
1.8K LED3
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
1K
D5
DS7
L1SS400
STBY
RES
VSS
XTAL
EXTAL
PF3/LWR/ADTRG
PF7
OSC1
OSC2
FW E
NMI
VCC
PF2/WAIT
AVCC
P40/AN0
P41/AN1
PF0/BREQ/IRQ2
PF6/AS
MD2
C116
C117
PF5/RD
VREF
MD1
MD0
LNJ426W83RA
PF1/BACK/BUZZ
PF4/HWR
0.1
0.1
Q9
R135 LDTC114EE
CP1
1.5K CH1L
DS6
100K
R68
C120
C118
LNJ426W83RA
R58
10K
C119
0.1
0.1
0.1
Q8
R136
LDTC114EE IC3 P30/TXD0 P42/AN2 R SSI
1.5K CH2L SI 76 50 LVIN
S-24C64CI-T8T1U3 P31/RXD0 P43/AN3
DS5 77 49 BATV
P32/SCK0/SDA1 P44/AN4
LNJ426W83RA 1 8 CLO 78 48 R114
A0 VCC P33/TXD1/SCL1 P45/AN5
Q7 2 7 CLI R116 79 47 100K CDEC
R137 A1 WP P34/RXD1/SDA0 P46/AN6
LDTC114EE 3 6 CIRQ 1K 80 46 SDEC
1.5K A2 SCL P35/SCK1/SCL0 P47/AN7
CH3L 4 5 ESDA 81 45 R127 BEEP
VSS SDA P36 P96/DA0
DS4 PGIO3 (MCH1) 82 44 1M SENC
P77/TXD3 P97/DA1
LNJ426W83RA PGIO2 (MCH0) 83 43
P76/RXD3 AVSS
C36
0.1
Q6 ESCL 84 42 SDEC2 CP2
R138 P75/TMO3/SCK3 P17/TIOCB2/TCLK
LDTC114EE PWON 85 41 OPV1
1.5K P74/TMO2/MRES P16/TIOCA2/IRQ1
CH4L CH4L 86 40 DSDA
P73/TMO1/CS7 P15/TIOCB1/TCLK
DS3 J3 CH3L 87 39 R120 POSW
P72/TMO0/CS6 P14/TIOCA1/IRQ1
LNJ426W83RA CPU5V CH2L 88 38 1K LED3
2 1 P71/TMRI23 P13/TIOCD0/TCLK
CH1L 89 37 LED2
DS1 4 3 P70/TMRI01 P12/TIOCC0/TCLK
DS2 90 36 LED1
LNJ426W83RA Q5 6 5 PG0/IRQ6 P11/TIOCB0/A21
LNJ426W83RA 91 35 R108 UNLK
LDTC114EE 8 7 PG1/CS3/IRQ7 P10/TIOCA0/A20
92 34 1K OPT3
10 9 PG2/CS2 PA3/A19/SCK2
R139 LIGT2 93 33 OPT1
12 11 PG3/CS1 PA2/A18/RXD2
1K LIGT2 94 32 OPT2
14 13 PG4/CS0 PA1/A17/TXD2
TLED 95 31 R109 PLST
PE0/D0 PA0/A16
RLED R111 96 30 1K (EPTT) PGIO1
PE1/D1 PB7/A15/TIOCB5
SCK 1K 97 29
PE2/D2 PB6/A14/TIOCA5 R121
SO 98 28 EXOE
PE3/D3 PB5/A13/TIOCB4
99 27 1K (OPV2) EXST
R112 PE4/D4 PB4/A12/TIOCA4
PGIO3
PGIO2
Q2 100 26
OPT3
OPT2
PWON
OPT1
1K R122
C87
0.1
0.001
RES
MD2
R11
390
LDTC114EE
PB2/A10/TIOCC3
PB3/A11/TIOCD3
C123
HD64F2238BTF13V
Dim ON 3.87V 1K
PB0/A8/TIOCA3
PB1/A9/TIOCB3
R12 LIGT1
Q1 470
Dim OFF 7.37V
EXB28V102J
2SC4116
PD2/D10
PD3/D11
PD4/D12
PD5/D13
PD6/D14
PD7/D15
PD0/D8
PD1/D9
PE5/D5
PE6/D6
PE7/D7
PC0/A0
PC1/A1
PC2/A2
PC3/A3
PC4/A4
PC5/A5
PC6/A6
PC7/A7
CVCC
CPU5V
R115
VSS
RK09D1130A1N
IC1
C128
0.001
0.1
C129
R20 R23
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CENC0 KR0
1
2
3
4
5
6
7
8
9
220K 47K KR1
0.001
KR2
C16
0.1
C14
R21
R14
CENC1 KR3
AFVI 56K 13
C124
14 R28
0.1
TENC
[VOL] CENC2 R22 R24 R26 R27 12 4.7K
R29
18K
C82
47P
0.018
47K
0.001
0.0012
0.001
100K
C15
CENC0
CENC1
CENC2
PGIO4
C130
C19
0.1
R60
LIGT1
C78
LDTC114EE
DUS E
IPTT
HANG
CP3
CCS
C17
R65 DUSE
R25
22K
1K
POSW
RSSI
PTTI
EXST
LVIN
SI
BATV
PLST
PGIO2
PGIO3
PGIO1
PGIO4
CIRQ
BEEP
NOIS
UNLK
TEMP
DSDA
PTTO
SCK
TENC
SDEC
OPT3
OPT2
OPT1
EXOE
CCS
(OPV3) DAST
OPV1
PWON
DIM DIM
CDEC
SO
TONE
S1
47P
DTCS ON 4.94V
(OPV2)
C2
0.047
KEY
(EPTT)
DTCS OFF 0V
C77
KR0
R90
KR1
C21 C125 390K
KR2 C23 BEEP
47P
0.001
47P
0.1
C4
KR3 0.01 J2
C3
1.5K
GND DIM
R77
R37 IC5 R38 R39 IC5 12
47P
R35 R36
C34
47P
R33 68K 68K 68K 3 68K 68K 5 TONE C38 TENC OPT3
56
KEY KEY KEY KEY 22K 1 7 47P NOIS OPT2
R32 78
R128 2 6 EXOE OPT1
91 0
15K
390P
0.001
C24
47P
11 12
C22
UNLK PTTI
C20
D2 13 14
C85
47P
PLST PGIO3
C131
EZJP0V080DA 15 16
CDEC 17 18 SCK
1
SDEC 19 20 SI
R129
OPV1 21 22 SO
8.12V
1K
J1 R18 RSSI CIRQ
23 24
8V 100K LVIN CCS
1 25 26
CLO R15 CLO TEMP MIC
2 27 28
AFO 1K AFO BATV EPTT C69
3 29 30
PTT R76 IPTT DSDA PGIO4 47P
4 31 32
M ICE 1K 8V PGIO2 PWON
5 33 34
MIC L1 R48 5V BEEP
6 35 36
GND MLF1608K 0 CPU5V L2 CPU5 8V
7 R16 37 38
CL I (HANG) CL I 4 NLV25T AFO GND C74
8 1K 39 40
C139
V+ ICIC5
EZJP0V080DA
C30
C28
0.1
47P
0.01
47P
10
0.001
R19 R44 GND NJM12902V
C25
0.001
C114
C126
C50
47P
C54
47P
C93
150K 11
47P
100K
EZJP0V080DA
C27
0.001
0.001
0.001
R45
PTT ON 0V
R42
47K
270P 8V
1M
C12
C10
C8
C26 R41
0.1 IC5
27K 9
D3
8 R46 C31
2.7K
10 1K 0.1
R47
4.7K
R43
39K
R40
C76
0.1
C84
47P
0.001
C41
*: Refer to the PARTS LIST for the value and name of component.
11 - 1
• MAIN-A UNIT (1/2)
BEEPO
CPU5V
TXC
8V
EAFO
VRAF
AFON
RMUTC
AFO
MMUT
MOD
HV
HV
R287 T8V
T8V
10K 5V
C252
0.1
Q35 D29 8V R8V
DTC363EK R8V
L1SS400
C176
R197
47P
8V
8V
R371
R194
2.2K
10K
39K
Q36 5V
C244
0.47
C246
R232 C280 R117 5V
LDTC144EE
0.1
RX AF HPF R370 AFOUT
470K 0.01 120K R116 0 CPU5V
CPU5V
12K
0.0015
R355 C249 C169 C168 C167 R330 R285
IC14 REF
C378
0.0022 B
R191
220K
0 IC16 0.047 0.047 0.056 4.7K 100 REF
H:AFON L:MUTE CD4066BPWR DISC
R159
1 14 12 BAL
10K
IC8 I/O1 VDD BAL
2 13 14
C250
C256 LA4425A 5 C253 O/I1 CONT1
0.1
R115
1.8K
1 C251 R195 3 12 13 NW C
J4 470 1 O/I2 CONT4 NW C
0.015
R196
100K
4 0.022 1K 4 11
C351
R193 I/O2 I/O4
2 5 10 T1
TX 8.2V 470K C245 C379 CONT2 O/I4
R118
R304 T1
R121
AF AMP 6 9
12K
R114
R120
47K
3 5 10K 0.01 0.015 CONT3 O/I3
12K
RX 0V 3 7
VSS I/O3
8 10K 5V T2
T2
Q25 4
R112
1 TMUT
R130
2SD1664
R119
5.6K
R111
3.3K
39K
0.001
TMUT
22K
R322
100K
C242
T8V
C491
0.1
2
0.001
8V TXC
0.001
C269
0.001
R329
6.8K
R198
R203
6.8K
R202
6.8K
R192
220K
TXC
C254
IC15
R199
C375
10K
DA221
10K
TA75S01F
C255
VREF VREF RXC
D23
470
RXC
MOD
0.001
2
3 4
MOD
R122
8.2K
C170
C180
0.001
R113
2.2K
C362
C272
47
F
J7
0.001
10
C276
Q29 SQIN
13.6V LDTC114YE SQIN
R125
100K
R123
100K
SCK
SCK
TX 0V C182 C181
VCC SO
RX 8.1V R129 0.01 0.1 SO
IC16
R297
300K
100 5 TLVA
3.3V 7 TLVA
R128
10K
BATV 6 RLVA
Q26 R183 RLVA
R8V
R126
R124
4.7K
R298
100K
470
2SA1577 220K C184 PLST
0.001
PLST
C270
150P
13.6V
C271
IC9 UNLK
10
UNLK
Q23 NJM7808DL1A R127
C183
8.1V
R205
0.1
2SJ506S-E 390K TEMP
10K
R391 TEMP
HV EP4 VCC I O 8V MIC AMP
W2 HF70BB9.5X10.4X4.9 R204 RXC 560K R384 LVIN
0.001
0.001
C258
G LVIN
C262
C265
C371
C261
C260
C431
220P
0.1
470
0.001
0.1
DSA3A1
R200
47P
C275
R133 C172 TONE RSSI
47K
Q30 RSSI
R185
120K
100K
C178
100P
0.01
D22
CP30 LDTC144EE
C316 NOIS
C266
C484
C465
R134
10
1
R244
390K
EP5 Q27 5V IC16
HF70BB9.5X10.4X4.9 2SB1132 9 R135 C174 SQL
R201 SQL
C274
8 270K
R137
0.001
R184 10
68K
C273
4.7K 10
10
C388
Q24 33K
6
0.1
R186
100K
0.0082
LDTC144EE C315
SDEC 1
C177
Power ON 4.9V R243 R242 0.022
3
SQL
BEEP
SQIN
REF
BEEPO
TENC
BAL
MCOT
82K 39K SPLATTER
Power OFF 0V IC16
FILTER
Q28
R245
C318 180K
R156 VREF
0.001
IC10 4.7K
R378
100K
C189
C317
820P
R241
100K
R240
100K
0.001
NJM2831F05
C175
0.1
1 5
5.0V
0.001
CTRL VIN
C263
2
C267
RX 5-TONE SIGNAL
GND
0.1
3 4 FILTER
R231
NC VOUT
R392
D/A
19
20
21
22
23
24
25
18K
C268
1K
C264
R188 C359
0.1
10
R187
560 1
VOUT4
VOUT5
VOUT6
VOUT7
VIN5
VIN6
10K
18 1
C179
5V
VIN4 VIN7
0.1
17 2
IC16 VIN3 VIN0
16 3
C349
MCGO
DISC
SIG
PGIO2
PGIO3
EPTT
SIGO
F
DIM
0.1
HORNO
NJM12902V
R250
PGIO4 4 15 4 VRAF
10K
R359 R361 VOUT2 AK2330 VOUT1
V+ 14 5
R251
2.2K
K 100K VIN2 VIN1
R358 R360 100K GND 13 6 5V
R252 VREF RSTN
E
1K 100K 11
SDATA
R230
100K
100K R368
C185
AVDD
DVDD
SCLK
I
R336
5.6K
R238
100K
R215
0.1
VSS
CSN
0
R253
C188
470
EAFO
47K
0.1
Q33
C292
Q37
47P
12
11
10
9
8
7
S1 3 4 0.1
R249 R248
MINISMDC050F
C190
0.01
VCC D61 D60 D59 2 5 22K 22K C186
R247
0.0068
DA221 DA221 DA221 0.1 C187
22K
0.039
R255
C322
1 6 0.1
C320
R254
10K
560
0.001
C293
Q39 5V 5V
F
D
R356
R357
J6 CDEC R256
1K
1K
10K
14
VCC CTCSS/DTCS
DAST
1 TX 5.0V
0.022
SCK
Ext.I/O 6 (DIM/IGSW) FILTER TX 0.9V
C325
SO
2 Q31
3 Ext.I/O 11 (HORN) 2SJ144 RX 0V
RX 4.7V
DISC
GND C295
4 1
Ext.I/O 7 (AFO) C288 R225
5
GND 0.1 0
6
R228
100K
R227
RSSI
PTTI
DISC
LVIN
PLST
PGIO2
PGIO3
EPTT
PGIO4
M CIN
CIRQ
EXST
BEEP
NOIS
BATV
TENC
SDEC
OPT3
OPT2
EXOE
CCS
DAST
OPV1
DIM
CDEC
UNLK
TEMP
DSDA
OPT1
PTTO
7
TONE
AFO
PWON
1M
SCK
GND C289 R224
8
SI
SO
IN 1 47 R138 MMUT
9
GND AFON 100K
10
R323
Ext.I/O 14(EPTT) R223
10K
DAP222
11
LDAN222
Ext.I/O 4 (SERIAL) 1K R226 R327
R325
12
D43
Ext.I/O 10(SERIAL) 100K
15
0.001
13 1K
0.001
0.001
EXB28V102J
D26
1K
C294
C290
C291
D44
R218
0.001
L1SS400
R229
0.001
22K
DA221
C436
C437
1M
IC17
D58
EXB28V102J
EXB28V102J
R142
EXB28V102J
R145
R143
R326
R144
R146
CD4094BPWR
EXB28V102J
AFONO
EXST 1 16 MMUTE
1K
1K
1K
1K
1K
STR V+
SO 2 15 EXOE
D OE
SCK 3 14
R150
R147
R149
R148
CLK Q5
CPU5V RXC 4 Q1 13 R381 TMUT
Q6
5 12 0 HORNO
Q2 Q7
5V J2 NWC 6 11 BUSY
Q3 Q8
GND DIM RMUT RMUTO 7 10
40 39 Q4 Q’S
R270
100K
R269
100K
TONE DAST 8 9
38 37 GND QS
R362
100K
DAP222
0.001
TENC OPT3
C361
36 35
C481
0.1
NOIS OPT2
R263
D42
R377
330K
R375
330K
R261
R262
R374
330K
34 33
EXOE OPT1
1M
32 31
1M
1M
R139
OPV1 EXST
30 29
PTTO
100K
TX 0V
EXST(OPV2) R373 20 21 SCK UNLK PTTI RMUTC
28 27 RX 5.0V
DAST(OPV3) 47K 19 22 SI PLST PGIO3
26 25
R372 18 23 SO CDEC SCK
24 23
OPT3 47K 17 24 SDEC SI
22 21 R345
OPT2 16 25 CIRQ OPV1 SO
20 19 100
OPT1 15 26 CCS RSSI CIRQ TX 0V
18 17
14 27
C283
SIGO REM CP28 LVIN
16 15
CCS
BUSY 13 28 TEMP MIC RX 5.0V IC20
10
C284
R363
14 13
C282
47P
M62334FP
10K
12 29 AFOUT BATV EPTT
12 11
10
MCIN 11 30 DISC DSDA PGIO4 8 1 T1
10 9 VCC AO1
10 31 R313 RMUT PGIO2 PWON 7 2 T2
8 7 SCL AO2
9 32 BEPO 1M C247 BEEP 5V BEEP 6 3 TLVA
6 5 SDA AO3
A
DSDA
MCOT 100 5 36 8V
SCK
0.001
R315
100K
4 37 5V
0.001
C207
0.001
0.001
C
0.001
C201
C208
0.001
C210
C202
3 38
C382
C226
C204
C311
0.1
C310
0.1
47P
47P
2 39 460mVrms
1 40
R314
100K
C203
0.1
J1
PTTO
PTTI
0.001
C209
*: Refer to the PARTS LIST for the value and name of component.
11 - 2
LK
NWC
MOD
TMUT
HV
LVIN
RLVA
RXC
F
5V
8V
TXC
BAL
RSSI
T2
T1
R8V
CPU5V
T8V
SQL
SO
REF
TEMP
UNLK
NOIS
PLST
SCK
DISC
TLVA
SQIN
MOD
NWC
TEMP
UNLK
4.6V
UNLK 0.5V
TMUT
HV
SO
F
RXC
5V
8V
TXC
CPU5V
BAL
SCK
T2
T1
R8V
RLVA
T8V
TLVA
REF
SQIN
PLST
LVIN
SQL
NOIS
DISC
RSSI
5V
5V
SO
5V
8V
NWC
SCK
PLST
UNLK
RLVA
W 4.9V
0V
C151
C309 0.1 C149
R103
100P
C323
0.33
CP1
0.01 150K
C154 R96
R237 C312 47P LVIN C147
Q34
680K 2.2
• MAIN-A UNIT (1/2)
0.1
*3 MULTI
8.1V
C153
1K
C397 C314
2SC4116
R93
R89
5.1V
R236 47P
Q18
R97
0.01 C486 C492 0.01
L35 1K 10K
R100 0.33 0.001
D37
2SK880
MLG1608S C152 10K R98
*R95
47P 2.2K
C305 C141
3.4V
56P 0.001 C148
6P
PLL
Q17
C376
L1SS400 IC4
Q40
10
16
15
14
13
12
11
10
9
C306
R350 5P C144
C143
27K
2SC4116
B
P
C155
L28
47P
1K
0.001
NC
FC
LE
C307 C138
D65
D64
270P
ELJNC
R101
L:NARROW H:WIDE
LDTA114EE
DATA
FOUT
56P 47P C354
CLOCK
C360
EP8
9P
L27
C135
HVD144A
C353
HVD144A
R352 C356 5P
0.001 4P
NLV25T
C398 3.3K L33 5V 7P C355
L39
FIN
D16
OSCIN
OSCOUT
VCC
GND
VP
DO
LD
R91 HVC376B-E HVC376B-E
0.1
0.1 HVC376B-E
3P
R353
C394
1
2
3
4
5
6
7
8
R92
22K
MMZ1005Y102CT
100K
C308
0.1
8.2K
MB15A02PFV1-G-BND-ERE1
WNC D31 L37
C385
I
HVC376B-E ELJFC
0.35-1.6-7TL
18P
L38
FI6
0.01
C399
C132 L53
O
FI2
C150 0.1 MLF1608K
R211
C127 L26
R401
LTM450HW
C337
0.001
0.001
47
I
1K
150K
R348
C6342A
LTM450FW
220P
C124
R354 C395
8.2K 0.25-1.9-7TL
82K
R90
0.1 C137
W
L25
Q19
SQIN 560P R86
0.1
C299 120K C195
C384
D67
D66
8P 0.22 1
L32
C347
0V
N 5.1V
MP 1
LDTC144EE
C145 D18 2
0.001
ELJRF
R351 470P HVL355CM C129 C196 3
0.25-1.9-7TL
L47 0.001 4
27K C298 1P
C350
L46
C71 NLV25T
0.068
15P F
C68
L44
0.1 C131
100P
C482
NLV25T
47
0.1
11 - 3
R42
EP9
ELJRF
R39
CC396
0.001 3.5P
15K C300 D52 C134
100K
R291
R40 C133
8P
HVC375B-E 33P
R44
18P
8P
R45
C69
220K
C126
1.5K
120K
C287 C197 D53 33P
100P
C297
R85
C114
R77
0.01
C165
R84
R46
MMZ1005Y102CT
2.2K
33P
3.9K
8
7
6
5
4
3
2
1
C158 C198 C121
C122
0
R79
47P
V+
100P TLVA R349
DEC
0
R328
C156
IFIN
270K
Q13
Q14
OSCIN
FILIN
0
4P
IF IC
D54
FILOUT
OSCOUT
R33R339
Q43
M IXOUT
TXC
R83
HVD144A R316
1.8K
R400
2SC4226
2SC4226
WNC 1K
2SK3019
SQL C67 C157 C163 C357 R78
TX VCO
RX VCO
15K
380 mVp-p
15.3 MHz
0.001
R342 T8V 0.1 L54
100P
IC1
0.001 1K
C66 ELJND R80
RX
4P
1K
GND
0.001 C116
QUAD
IFOUT
AFOUT
5
4
R395
NOISEREC
C161
R43
N OISEDET
R SSI
MIXIN
R340 C474 RXC
NJM2591V
Q16
9
10
11
12
13
14
15
16
Q15
1 1 C75 C119
0V
TX 4.2V
C117
C113
15K
RSSI 10 R317
0.75P
0.001 0.001
R341
XP1214
LDTC144EE
0.5P
C118
1K
R41
NOIS D55
1
2
3
3
4
R38 HVD144A 0.1
7.2V
4P MMZ1005Y102CT
TX
OUT
VCC
C63 0.001 C286 47P
47P C160 4P C139
270K
R397
R36 0.1 0.1
RX 4.5V
0V
1
3
EP7
2.2K
C61
1
2.2K
R394
X2
22P
C285
22P
C62
100P
C488
2
0.001
180K
R396
GND
C490
VCON
X1 C162 R76
CR-794
R37
0.01 L41 100
C64
JTBM450CX70
2
1
3.9K
IC21
0.01
ELJRF
100K
R399
4
R74
MMZ1005Y102CT
5 TA75S01F
330 R75
Q12
Q4
Q11
5.0V
R398
Q5
R8V 220K R73
L22
100 C142 100
R221
R34 ELJRF
2SC5006
C105
2SC5006
C489 0.001
IF AMP
2SC5107
0.1 220K 5V 0.001 C110
LDTC144EE
NWC 0.001
R209
C58
L:NARROW H:WID E C60 C103
10
C101 12P
0.001
0.01
R35
C104
IC19
4
560 C59
82K
47P
180K
R105
R106
TA75S01F 2
5
R210
N
100 10P
RX 2.3V
TX 2.4V
TX
TEMP
Q10
2
4
R311
RX
W 4.9V
0V
C164 C109
220
RX 3.0V
0V
RX 7.5V
0V
OUT
GND
0.001
270K
R110
10K
IN
*FI1
C100
82K
D14 R67 R68
3
1
47K
C303 R50
0.1 100 HVD144A
0.001 470
TX
R69
10
C54 4.7K
R32
10P
BAL
REF
C477
C302
R8V
0.001
220P C106
RX 0.5V
0V
10K
47P
R235
L13 C476
18P
C93
C51
0.001 ELJND 0.001 C472
Q3
C52 0.001
MIX
10P
3SK293
R385
DRIVER
R301 L23
C50 47
C478 R388 ELJRE
0.001 150K
0.001 33
RX 8.1V
0V
C108
C48
Q9
18P
0.01
C460
0.1 R387
C461 4.7K
R302 C451
2SC3357
0.001
56K R299 10
R300
180K *C381 C458
56K
18P
C41
18P
C41
C457
0.001
C390 0.001
*C456
47P
L4*L43
0.001 47P
C392
C392
RX
C44
0.5P C57
0.001
L11
C462
0
0V
TX 6.7V
L36
C2520C
0.001
R332
*R212
C45
0.001 R337 R393
C94 0 1.5K
8P
C49
*D9
AS080547-47N
C43 R23
18
3 2 2.2
C40
470
R390 R21 C342 *IC3
12
C86 R338
R28
10K
R22
C42 7P C468
3
C343
47P
0.001
0.001
L9 R17 C369
NFM60R20T152
T8V
C2520C *C403
C32 100 68P C85
C466 C469
Q2
C333
AS080547-47N
RF AMP
100K
*FI5
47P C470
3
TX
68P
RX
C31
0V
TX 5.3V
R15 C33
270K 0.1 0.1
RX
C34 L5
10P
C30
10K
TX
C363
R319
0.015
C29
D3
C12 C443
1P 0.001 47P
*D47
RN752
L4
RX 5.9V
0V
*R49 AS080547-47N
C26 *D48 *R48
D4
22P D12 C9
C14
0.1
Q1
4.7K *C4
*C411
RX
C15 C77 R9
C22
HVC375B-E
R53 22P
10K
R14
*R10
L6
220
4
C20 D8 D1
C28
L3
APC
LPF
LRB706F
*Q20
C2520C
22P HVC375B-E
0.001
C79
R56
L7
D62
0.22
150K
C409
2
5
C2520C R4
DA221
4P
0.001
10K C3
TX
C442
8P 0.001
*R5
IC2
L2
R59 C404
470K
R320
R51
RX 1.0V
0V
D6
10K
R57
12P
C25
1 TA75S01F
C11
12P
AS080547-47N
0.001
C2012C-56NG
C73 R7
1 10K C5
C18 C78
0.5P
R55
0.001
C19
6P
4.7K
C2
TX
L1
0.001
22P
C88
0.001 C1
RX 1.8V
TX 3.5V
RX 4.9V
0V
18P
C479 C480
AS080547-47N
HV
T8V
0.001 0.001 R1
13.6V
100K
TMUT
T1
R8V
RSSI
W1
*: Refer to the PARTS LIST for the value and name of component.
RDS2T0R0
1-1-32, Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Phone : +81 (06) 6793 5302
Fax : +81 (06) 6793 0013
URL : http://www.icom.co.jp/world/index.html
Ctra. Rubi, No. 88 Bajos A 08174, Sant Cugat del Valles, Barcelona, Spain
Glenwood Centre #150-6165
Phone : +34 (93) 590 26 70 Fax : +34 (93) 589 04 46
Highway 17 Delta, B.C., V4K 5B8, Canada
URL : http://www.icomspain.com
Phone : +1 (604) 952-4266 Fax : +1 (604) 952-0090
E-mail : [email protected]
URL : http://www.icomcanada.com
E-mail : [email protected]
Blacksole House, The Boulevard, Altira Business Park, Herne Bay, CT6 6GZ, UK
Unit 1 / 103 Garden Road, Clayton VIC 3168 Australia Phone : +44 (01227) 741741 Fax : +44 (01227) 741742
Phone : +61 (03) 9549-7500 Fax : +61 (03) 9549-7505 URL : http://www.icomuk.co.uk
URL : http://www.icom.net.au E-mail : [email protected]
E-mail : [email protected]
Zac de la Plaine
146A Harris Road, East Tamaki, 1 Rue Brindejonc des Moulinais BP 5804
Auckland, New Zealand 31505 Toulouse Cedex, France
Phone : +64 (09) 274 4062 Fax : +64 (09) 274 4708 Phone : +33 (5) 61 36 03 03 Fax : +33 (5) 61 36 03 00
URL : http://www.icom.co.nz URL : http://www.icom-france.com
E-mail : [email protected] E-mail : [email protected]