Scribd
Upload
9 views

Designation System SKF

About bearings detailed descriptions

Uploaded by

vijayhjmech
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
9 views

Designation System SKF

About bearings detailed descriptions

Uploaded by

vijayhjmech
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

 AUSTRALIA  CONTACT  LOG IN

Home / ... / Rolling... / ...


/ Spherical roller bearings

Section navigation m

Designation system

The designations of most SKF rolling bearings


follow a system that may consist of a basic
designation with or without one or more
prefixes and/or suffixes (Basic bearing
designation system).

An example and the applicable options for


spherical roller bearings are given below.

Example
24013 CCK30/W33 where 24013 =

CC =

K30 =

W33 =

Applicable options
Prefixes

BS2-.. Bearing, designated by a drawing number


ZE Bearing with SensorMount feature

Basic designation

Listed in table 1
Figure with four digits: drawing number identification

Suffixes - Internal design

BC Bearing for wind turbine main shafts with


roller-guided cast iron cage (unless one of
the cage design suffixes is specified)
CA, CAC Retaining flanges on the inner ring, guide
ring centred on the inner ring, machined
brass cage (unless one of the cage design
suffixes is specified)
CC(J), Flangeless inner ring, guide ring centred
CJ on the inner ring, two stamped steel cages
CCJA, Flangeless inner ring, guide ring centred
EJA on the outer ring raceway, two stamped
steel cages
E Optimized internal design for increased
load carrying capacity
213, 222 and 223 series: Flangeless inner
ring and two stamped steel cages. Annular
groove and three lubrication holes in the
outer ring.
d ≤ 65 mm: Guide ring centred on the
inner ring
d > 65 mm: Guide ring centred on the
cage

Suffixes - External design (seals,


snap ring groove etc.)
-CS, Contact seal, NBR, on one or both sides
-2CS
-CS2, Contact seal, FKM, on one or both sides
-2CS2
-CS5, Contact seal, HNBR, on one or both sides
-2CS5
-CS6, Contact seal, G-ECOPUR  , on one or
-2CS6 both sides
-RS, Contact seal, NBR, on one or both sides
-2RS
-RS5, Contact seal, HNBR, on one or both sides
-2RS5
K Tapered bore, taper 1:12
K30 Tapered bore, taper 1:30

Suffixes - Cage design

F Machined steel cage, inner ring centred


FA Machined steel cage, outer ring centred
J Stamped steel cage, inner ring centred
JA Stamped steel cage, outer ring centred
MA Machined brass cage, outer ring centred

Suffixes - Materials, heat treatment

235220 Case-hardened inner ring with a helical


groove in the bore
HA3 Case-hardened inner ring

Suffixes -Accuracy, clearance,


preload, quiet running
C08 Geometrical tolerances (tolerances of run-
out and orientation) to class P5
C083 C08 + C3
C084 C08 + C4
C2 Radial internal clearance smaller than
Normal
C3 Radial internal clearance greater than
Normal
C3H Radial internal clearance in the upper half
of the C3 range
C4 Radial internal clearance greater than C3
C4L Radial internal clearance in the lower half
of the C4 range
C5 Radial internal clearance greater than C4
P5 Dimensional and geometrical tolerances
(tolerances of run-out and orientation) to
class P5
P6 Dimensional and geometrical tolerances
(tolerances of run-out) to class P6
P62 P6 + C2

Suffixes - Bearing sets, matched


bearings (n.a.)

Suffixes --Stabilization
Stabilization (n.a.)

Suffixes - Lubrication

GEA8 Filled to 60 – 80% with SKF LGEV 2


grease
GEM9 Filled to 70 – 100% with SKF LGHB 2
grease
GLE Filled to 25 – 45% with SKF LGWM 2
grease
VT143 Filled to 25 – 45% with SKF LGEP 2
grease
VT143B Filled to 45 – 60% with SKF LGEP 2
grease
VT143C Filled to 70 – 100% with SKF LGEP 2
grease
W64 Solid Oil
W Without annular groove and lubrication
holes in the outer ring
W20 Three lubrication holes in the outer ring
W26 Six lubrication holes in the inner ring
W33 Annular groove and three lubrication holes
in the outer ring
W33X Annular groove and six lubrication holes in
the outer ring
W77 Plugged W33 lubrication holes
W513 W26 + W33

Suffixes - Other variants

R505 Bearing for railway axleboxes


VA405 Bearing for vibratory applications,
surface-hardened stamped steel cages
VA406 Same as VA405, but PTFE coated
cylindrical inner ring bore
VA991 Bearing for high-speed applications
VA9B1 Bearing for continuous caster
applications
VE552(E) Outer ring with three equally-spaced
threaded holes in one side face to
accommodate lifting tackle. The E
indicates that appropriate eye bolts are
supplied with the bearing.
VE553(E) Same as VE552(E), but threaded holes in
both side faces
VG114 Surface-hardened stamped steel cages
VQ424 Geometrical tolerances (tolerances of
run-out and orientation) tighter than C08

O R G A N I S AT I O N k

CAREER k

NEWS AND MEDIA k

I N V E STO R S k

C O N TA C T k

SOCIAL

SKF IS ON

© Copyright Terms of use

Privacy policy Site ownership

General conditions of sales Cookies


l
Cookie settings BACK
TO TO P

You might also like