Scribd
Upload
5 views

Group One Assignments

Typ

Uploaded by

Mahamed
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
5 views

Group One Assignments

Typ

Uploaded by

Mahamed
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 19

MOBILE AND WARELESS

Subject: mobile and wireless communication


Assignments in semester six
Group one
Name Mohamed raage saalax
Ahmed Adan Abdullahi

Topic : Signal Encoding Techniques


Date : 09/may/2020

Contents

 Digital Data, Digital Signal

 Digital Data, AnalogSignal


 AnalogData, Digital Signal
 AnalogData, AnalogSignal

Signal Encoding Techniques

fc(En)coder/Decoder = codec

Modulator/
demodulator
= modem
Modulation: encode source data onto a carrier signal with frequency fc(

Four Different Options

2
Digital Data, Digital Signal
•Digital signal–Discrete, discontinuous voltage pulses–Each pulse is a signal element; the
rate at which pulses are sent is called the signallingrate–Binary data encoded into signal
elements•Most obvious example: high voltage = bit 1; low voltage = bit 0•However, these is
not used in practice!•Some techniques encode multiple bits into one signal element (pulse)

Interpreting Signals

•A receiver needs to know


–Timing of bits –when does the bit start and end?
•Try to sample the bit in the middle of the signal element
–Signal levels –when is it a 0 or 1?
•Use a threshold: if the sample value is above the threshold, then value A; if below the
threshold then value B
•Factors affecting the received signal, and ability to interpret correct bits:
–Signal to noise ratio (SNR)
–Data rate
–Bandwidth
–Encoding scheme

Encoding Schemes
•An encoding schemes:
–Define the sequence of high and low signals to transmit 0’s and 1’s

3
–The benefits of different encoding schemes can be:
•Can shape the output spectrum to be more efficient
–Very low frequencies (DC components) cannot pass through some systems; often need to
remove these components from signal
•Detect errors: if a sequence of signals are received that are unexpected, then an error may be
detected
•Avoid errors due to noise
•Simplify digital circuits (hence lower cost)
–Higher signallingrate for a given data rate leads to higher cost
–Examples: Non-return to Zero (NRZ); Alternate Mark Inversion (AMI); Manchester; B8ZS;
HDB3; …

Non-Return to Zero (NRZ)


•Non-Return to Zero Level (NRZ-L)–Negative voltage represents binary 1–Positive voltage
represents binary 0•(or other way around)•A variant: NRZ Invert on ones (NRZI)–A
transition (from high to low or low to high) represents binary1–No transition represents
binary 0

Digital Signal Encoding Formats

•Nonreturnto Zero-Level (NRZ-L)


–0 = high level
–1 = low level
•Nonreturnto Zero Inverted (NRZI)
–0 = no transition at beginning of interval (one bit time)
–1 = transition at beginning of interval
•Bipolar-AMI
–0 = no line signal
–1 = positive or negative level, alternating for successive ones
•Pseudoternary
–0 = positive or negative level, alternating for successive zeros
–1 = no line signal
•Manchester
–0 = transition from high to low in middle of interval
–1 = transition from low to high in middle of interval
•Differential Manchester
–Always a transition in middle of interval
–0 = transition at beginning of interval
–1 = no transition at beginning of interval

4
•B8ZS
–Same as bipolar AMI, except that any string of 8 zeros is replaced by a string with two code
violations
•HDB3
–Same as bipolar AMI, except that any string of 4 zeros is replaced by a string with one code
violation

Digital Signal Encoding Formats

Digital Data, Analog Signal

•The public (fixed, wired) telephone system is best example of analog transmission system
–Analog signals are sent in the voice frequency range of 300Hz to3400Hz
–(Voice over telephone system is example of analog data, analog signal)
–To make use of this analog transmission system to send digital data, need to modulate data
onto a analog signal (carrier)
–Device that modulates and demodulates: modem
•Encoding techniques
–Modulation is performed by varying analog signal amplitude, frequency or phase
•Amplitude Shift Keying (ASK)
•Frequency Shift Keying (FSK)
•Phase Shift Keying (PSK)
•And combinations …

Modulation Techniques

5
Amplitude Shift Keying

•Encode 0/1 by different amplitudes of the carrier signal


–Usually have one amplitude zero, and the other non-zero
•Simple, but has problems for telephone lines:
–Susceptible to sudden gain changes and distortion
–Inefficient use of bandwidth
•Used for
–Up to 1200bps on voice copper lines
–Very high speeds over optical fiber

Frequency Shift Keying

•Use different frequencies to represent digital data


–Most common is Binary FSK
•Two binary values represented by two different frequencies (nearcarrier)
•Less susceptible to error than ASK
•Used for
–Up to 1200bps on voice grade lines
–High frequency radio
–even higher frequency on LANs using co-axial cable

6
Phase Shift Keying

•Phase of carrier signal is shifted to represent data


•Binary PSK
–Two phases represent two binary digits

•Differential PSK
–Phase shifted relative to previous transmission rather than somereference signal
•QuadraturePSK
–Shift phase by 90 degrees; a signal represents two bits (00, 01,10, 11) depending on phase
shift (45°, 135°, 225°, 315°)
–More efficient: carry more information (bits) per signal
•QuadratureAmplitude Modulation
–Combines ASK and PSK
–Used, for example, in ADSL modems

Analog Data, Digital Signal

•Involves digitizationof analog signal


–Convert analog data to digital data
–Then send digital data using, for example:
•NRZ-L or similar code
•Or convert to analog signal and send
•Analog to digital conversion done using a codec
–Pulse Code Modulation
–Delta Modulation
•Simpler than PCM, but not as good performance

Pulse Code Modulation (PCM)

7
•PCM is used to convert analog data to digital data
•Sampling theorem:
–“If a signal is sampled at regular intervals at a rate higher than twice the highest signal
frequency, the samples contain all information inoriginal signal”
–E.g. 4000Hz voice data, requires 8000 samples per second
•Sampling an analog signal (data) creates Pulse Amplitude Modulation (PAM) samples
–E.g. Assume the analog data has an normalized amplitude between 0 and 16. Then one
sample gives a PAM value of 1.1, the next sample a PAM value of 9.2, and so on…
•Each PAM sample is assigned a code (Pulse Code Modulation)
–E.g. Assume using 4-bit samples, then code 0000 (decimal 0) would be assigned to the
samples with PAM between 0 and 1; code 0001 (decimal 1) assigned to PAM between 1 and
2; and so on…
•The PCM codes represent the digital data to send

PCM Example

PCM Performance

•Analog (continuous) data is converted to digital (discrete) data


•When the digital data arrives, the receiver must be able to reconstruct the original analog
data
–The Sampling Theorem defines how many samples are needed to reconstruct the
information
–How big should each sample be?
•The larger the sample, the better quality of the received data, but the more bandwidth
required
•Performance Example:
–Voice (analog) data has a maximum frequency component of 4KHz
–Need to sample at 8000 samples per second
–Good voice reproduction typically requires 128 levels, that is 7bit PAM codes
–Therefore, voice data can be sent at 56Kbit/s
•Sending voice as analogsignal requires 4KHz of bandwidth
•Sending voice as digital signal requires 28KHz of bandwidth (according to Nyquist)
•But advantages of digital signals (such as combining multiple signals into one, repeaters not
accumulating noise, …) mean they are desired in telecommunications systems

Analog Data, Analog Signals

8
•Nothing needed –just send the analog data as a signal?
–But often want to send the analog data at a different frequency,that is, modulate the analog
data onto a carrier signal
•Why modulate analog signals?
–Higher frequency can give more efficient transmission
•Example: for wireless transmission need a larger antenna for lower frequencies. The low
frequencies music and speech would need antennas many kilometresin diameter if not
modulated!
–Makes Frequency Division Multiplexing easier (combined multiple signals into one signal -
covered in later topic)
•Types of modulation
–Amplitude (AM)
–Frequency (FM)
–Phase (PM)
•Trade-offs between techniques: bandwidth used, power required, resilience to errors, …

THANK YOU

END

9
10
11
12
13
14
15
16
17
18
19

You might also like