HCPP-IP Network

1. CampusInsight collects data using the SNMP protocol instead of the streaming telemetry
technology – a de facto standard in the industry.
A. True
B. False
2. Through AI-powered intelligent O&M and by focusing on user experience, iMaster NCE-
CampusInsight delivers visualized user experience management.
A. True
B. False
3. iMaster NCE-Campus can synchronize user groups and user accounts from Active Directory (AD)
and other standard Lightweight Directory Access Protocol (LDAP) servers. Administrators can
enable this function when configuring user access and authentication, without needing to
manually add user accounts.
A. True
B. False
4. The automatic routing domain configuration function of the CloudCampus Solution supports
automatic deployment of dynamic routing protocols on the underlay network. With this function
enabled, iMaster NCE-Campus will automatically configure the OSPF protocol on the underlay
network, implementing route reachability between fabric nodes.
A. True
B. False
5. Huawei central APs cannot be used in public cloud or MSP-owned cloud scenarios of Huawei
CloudCampus Solution.
A. True
B. False
6. Both Cisco DNA and Huawei CloudCampus solutions can deploy HQoS to implement hierarchical
traffic scheduling based on user and service priority levels.
A. True
B. False****
7. Huawei CloudFabric data center network Solution Provides Customers with Intelligent Ultra-
Broadband, Intelligent Connection and Intelligent O&M data center network.
A. True
B. False
8. It is recommended that the IP address of a loopback interface on a switch be used instead of the
IP address of a physical interface as the VTEP IP of a VXLAN tunnel.
A. True
B. False
HCPP-IP Network

9. In a network overlay scenario, all NVE nodes on the VXLAN network are physical switches.
A. True
B. False
10. A typical WPA or WPA2 security policy involves link authentication, access authentication, and key
negotiation, but does not involve data encryption.
A. True
B. False****
11. A management VLAN is used to transmit packets that are forwarded through CAPWAP tunnels,
including management packets and service data packets forwarded through CAPWAP tunnels.
A. True
B. False
12. In direct forwarding mode, the AC centrally forwards and processes data and manage services of
APs.
A. True
B. False
13. Wi-Fi 6 supports various GI lengths. A larger GI is recommended for indoor areas with low
interference, while a small GI is recommended for outdoor areas with high interference.
A. True
B. False
14. On a WLAN, multiple BSSs can have the same SSID so that users are unaware of BSS changes.
A. True***
B. False
15. An AP needs to cover large an area as possible to provide better coverage in high-density
scenarios.
A. True
B. False***
16. iMaster NCE-Fabric synchronizes resource with the VMM and detects VM login and logout
information RESTful APIs.
A. True
B. False
17. Only Huawei internal technical managers can use SCT while channel partner users cannot use it.
A. True
B. False
18. In cloud AP networking, the APs are managed and configured by the cloud management platform
in a unified manner. The calibration algorithm works as follow: An AP detects and collects radio
HCPP-IP Network

and interference information of its neighboring APs, and then reports the information to the cloud
management platform for centralized calibration calculation. After the calculation is complete, the
cloud management platform delivers the allocated channel and the corresponding power to each
AP.
A. True
B. False
19. The CloudFabric solution does not support co-deployment of the spine node, border leaf node,
service leaf node, server leaf node, and DC gateway.
A. True
B. False
20. The simulation and verification function of iMaster NCE-Fabric allows an administrator to preview
and confirm configurations before delivering them to network devices. However, iMaster NCE-
Fabric cannot simulate connectivity between new and old.
A. True
B. False**
21. Which of the following is not a feature of Telemetry technology?
A. Based on HTTP and Protobuf
B. Reporting subscripted data
C. Minute-level periodic polling**
D. Efficient encoding and decoding, enabling multiple data records to be obtained at a time in less
than 1 second.
22. Which of the following capabilities is not provided by iMaster NCE-Campus?
A. Functions as a Portal server
B. Network management and monitoring
C. PKI certificate generation and management
D. Device upgrade
23. Which of the following operations will a device perform after it is disconnected from the cloud
management platform in the CloudCampus solution?
A. Restarts itself***
B. Clears its configuration**
C. Switches to the cloud mode
D. Reconnects to the cloud mode
24. Which of the following statement about the IP-security group synchronization function is false?
A. When an authenticated user who is allocated to a security group accesses network resources
through the VXLAN tunnel, the VXLAN packets carry user group information. The access device
HCPP-IP Network

(on the network where the network resources to be accessed reside) decapsulates the VXLAN
packets, identifies the security group of the user, and can authorize the user using the locally
configured group policy. In this case, you do not need to create IP-security group entry
subscription.
B. The IP-security group synchronization function enables the free mobility solution to be
compatible with third-party devices. When a third-party is used as the authentication point on
the network, the authentication point must interconnect with iMaster NCE-Campus, and iMaster
NCE-Campus functions as the authentication server.
C. ****All Huawei switches can be configured as IP-security group entry subscription devices
D. The authentication point communicates with the RADIUS authentication server. iMaster NCE
Campus records users’ IP-security group entry information.
25. Which of the following key factors is used by the cloud management platform to determine the
tenant to which a device belongs
A. Device IP Address
B. Device MAC address
C. Device ESN
D. Device model*****
26. Which of the following vendors provides a campus network solution that simultaneously supports
MSP-owned cloud, public cloud, and on-premises deployment modes?
A. Huawei
B. W
C. Meraki
27. Which of the following statements is false about underlay and overlay networks?
A. An overlay network is logical network built over a physical network (underlay network)
B. Generally, VXLAN is used to implement the overlay network.
C. The underlay and overlay network must use the same routing protocol
D. The underlay network is transparent to devices (servers, VAS devices, and external routers)
connected to NVE nodes
28. In the overlay network design, which of the following RR deployment modes is recommended for
deploying EVPN across multiple PoDs?
A. Single-AS, single-level RR
B. Single-AS, hierarchical RRs
C. ****Multiple Ass, and establishment of EBGP peer relationship between RRs in each PoD
HCPP-IP Network

D. None of the above “All of the above”

29. Which statement about Navi AC deployment is true?
A. The Navi AC must use the same version as the local AC
B. Both local and Navi ACs support dual-link backup
C. ****The service VLAN, SSID, user isolation, and authentication mode in the VAP profile on the
local AC must be the same as on the Navi AC.
D. STAs can roam between Navi ACs
30. In DHCP packets, different Option fields carry different information. The ( ) field carries AC IP
addresses, and the ( ) field carries AC domain names (resolved into AC IP addresses from the DNS
server).
A. Option 15, Option 43
B. Option 60, Option 82
C. Option 43, Option 15
D. Option 43, Option 60
31. In static load balancing mode, what is the maximum number of members supported in a load
balancing group?
A. 6
B. 8
C. 12
D. 16
32. Which of the following types of devices will trigger a rogue device alarm when it is identified as a
rogue device?
A. Rogue AP****
B. Rogue STA
C. Wireless bridge
D. Ad-hoc device
33. Based on design principles which of the following is the required minimum field strength at the
coverage edge of a WLAN? -65dBm
A. -100 dBm
B. -90 dBm
C. -75 dBm****
D. -70 dBm
HCPP-IP Network

34. The 5 GHz frequency band in the WLAN has abundant spectrum resources. FCC has allocated 23
non overlapping 20 MHz channels. Which of the following is the maximum bandwidth stop a
bonded channel on this frequency band?
A. 40 MHz
B. 80 MHz
C. 160 MHz***
D. 320 MHz
35. Which of the following can be viewed on the SCT home front page?
A. Hotselling products
B. Pre-sale products
C. EOM Products
36. CloudCampus supports intelligent terminal identification. Which of the following methods is used
to identify terminals that use Portal authentication?
A. mDNS
B. HTTP UserAgent
C. DHCP Option
D. LLDP
37. Which of the following statements about the underlay network is false?
A. the underlay network is the bearer plane of the VXLAN network
B. the underlay network consists of VXLAN-enabled NVE nodes and devices that only forward IP
packets.
C. The underlay network has independent forwarding plane and control plane protocols. The
forwarding plane uses IPv4, and the control plane uses OSPF or EBGP.
D. ***The underlay network cannot ensure Layer 3 reachability.
38. Which of the following statements about roles in the CloudFabric solution is false?
A. spine nodes and border leaf notes can be combined
B. service leaf nodes and border leaf nodes can be combined
C. **server leaf nodes and border leaf nodes cannot be combined
D. DCI gateways and border leaf nodes can be combined
39. which of the following functions is not supported by Huawei WLAN planner?
A. AP calculator***
B. Locating a deployed AP
C. WLAN signal simulator
HCPP-IP Network

D. Material list export

40. which of the following apps is developed by Huawei to provide fast and professional WLAN
planning and experience evaluation?
A. CloudCampus APP
B. inSSIDer
C. WLAN Planner
D. SpeedTest

MULTIPLE ANSWERS
41. Which of the following can be checked using protocol tracing in iMaster NCE-CampusInsight?
A. User MAC address and username
B. User access time
C. AP that a STA connects to
D. Access experience
42. the registration center connects to iMaster NCE-Campus in the northbound direction and uses a
unique southbound IP address to connect to cloud managed devices in the southbound direction.
To synchronize device data from the registration center, an administrator can configure
interconnection between iMaster NCE-Campus at the registration center. Preset with the domain
name of the registration center, cloud manage devices can obtain the IP address of iMaster NCE-
Campus from the registration center and then send the registration request to iMaster NCE-
Campus, implementing device plug-and-play. In which of the following scenarios is the feature
supported?
A. MSP-owned cloud scenario
B. Huawei public cloud scenario
C. On-premises scenario
D. Amazon public cloud scenario
43. Which of the following methods can be used to import devices to iMaster NCE?
A. importing devices manually
B. importing devices in a batch
C. importing devices by scanning device barcodes using the CloudCampus APP
44. In Huawei CloudCampus Solution, which of the following may be the cause of a cloud-managed
device failing to registered in Huawei public cloud scenario?
A. the device is not included in the license authorization package
B. the configuration for device registration is incorrect
C. the device has not been added to a site
HCPP-IP Network

D. the device fails to automatically obtain an IP address

45. which of the following devices are cloud managed devices in Huawei CloudCampus Solution?
A. AR
B. Firewall
C. Switch
D. AP
46. Which of the following are the key values of Huawei CloudCampus Solution?
A. the cloud management platform can be leased or sold
B. users under different tenants can manage their respective networks on the same cloud
management platform
C. full-lifecycle automation greatly reduces OpEx
D. devices support plug-and-play
47. which of the following sales modes are supported by Huawei’s CloudCampus Solution?
A. Perpetual license + SnS mode
B. embedded software mode
C. term based license (TBL) mode
D. SaaS mode
E. A-la-carte mode
48. Which are the TOP3 industries Huawei CloudFabric Solution focus?
A. finance
B. government
C. ISP
D. Oil&gas
49. which of the following physical network and protocol design modes are suitable for medium and
large sized networks?
A. OSPF is used on the underlay network, and only area 0 is configured.
B. EBGP is used on the underlay network
C. The number of spine nodes is increased from 2 to 4
D. Super-spine nodes are added to connect spine nodes of multiple PoDs
50. Which of the following may cause APs to fail to join an AC?
A. The license on the AC is insufficient
B. The AP blacklist is configured on the AC
C. A loopback interface is configured as the CAPWAP source interface of the AC
HCPP-IP Network

D. When an AC and an AP are deployed on a Layer 3 network, the AP obtains an incorrect IP address
of the AC from the Option 43 field carried by the DHCP server
51. Which of the following security functions does AAA represent?
A. Authentication
B. Encryption
C. Authorization
D. Accounting
52. In which of the following conditions will an AP broadcast a DHCP discover message to discover an
AC?
A. The AP does not have an AC IP address list
B. The AP does not receive a response after unicasting the DHCP Discover message
C. The AP and AC are connected at Layer 2, and the AP has obtained the AC’s IP address through
Option 43
D. The AP is statically configured with an IP address and AC list
53. Which of the following devices should be kept far from APs to avoid interference?
A. Microwave ovens
B. Bluetooth devices
C. Wireless game controllers
D. Cordless phones with the same frequency band as APs
54. Which of the following channels belong to the 5.8 GHz frequency band supported in China?
A. 149
B. 151
C. 153
D. 155
55. Which of the following factors should be considered when calculating the EIRP?
A. AP transmit power
B. MIMO gain
C. Antenna gain
D. Feeder loss
56. Which of the following statements are true about cabling design in WLAN planning and design?
A. The ethernet cable between an AP and a switch cannot exceed 100 m (80 m in some special
scenarios)
B. The length of an Ethernet cable should be equal to the distance between a switch and an AP
HCPP-IP Network

C. Ethernet cables should be kept as far as possible from strong electromagnetic fields
D. You must communicate with the customer about the cabling feasibility to ensure that cabling will
not be affected by asset management or decoration requirements
57. Which of the following statements about the VLAN design on a campus network are true?
A. During VLAN planning, it is recommended that consecutive VLAN IDs be allocated to ensure
proper use of VLAN resources
B. It is recommended that a specific number of VLANs be reserved for future use
C. VLANs are classified into service VLANs management VLANs, and interconnection VLANs
D. Typically, Layer 2 switches use VLANIF interface addresses as management addresses. As such, it
is recommended that an independent VLAN be planned for each Layer 2 switch to avoid conflicts
between VLANs
58. Which of the following statements about microsegmentation are true?
A. It provides isolation in different subnets
B. It provides isolation within a subnet
C. It provides isolation based on discrete IP addresses
D. It provides VM name-based isolation
E. It is a finer-grained isolation mechanism
59. Which of the following are CloudFabric multi-DC solutions?
A. Multi-PoD
B. Multi-site
C. Public cloud
D. Hybrid cloud
60. Which of the following functions can be implemeted through Huawei WLAN Planner?
A. Automatic AP deployment
B. Field strength simulation display
C. 3D simulation
D. Onsite signal scanning
TRUE OR FALSE
61. Through AI-powered intelligent O&M and by focusing on user experience, iMaster NCE-
CampusInsight delivers visualized user experience management.
A. True
B. False
HCPP-IP Network

62. Telemetry supports collection of network data in seconds. An analyzer heavily relies on
Telemetry’s quasi-real-time data obtaining capability to mine data.
A. True
B. False
63. In Huawei CloudCampus Solution, VXLAN can be deokited across core and aggregation layers, or
across core and access layers
A. True
B. False
64. When it comes to automatic overlay configuration, Huawei supports easy replacement of faulty
aggregation and access devices by scanning barcodes. Cisco has no such feature.
A. True
B. False
65. CloudFabric Easy solution is using fixed switches.
A. True
B. False******
66. CloudFabric abstracts Layer 2 VXLAN into logical switches. Logical switches provide Layer 3 routing
services and gateway services between logical ports
A. True
B. False
67. in a distribution VXLAN gateway scenario, leaf nodes function as VTEPs of VXLAN tunnels, and
each leaf node can functions as a Layer 3 VXLAN gateway in the typical spine-leaf networking
A. true
B. false
68. during CAPWAP tunnel establishment, an AP establishes a DTLS session with an AC. If DTLS
encryption has been enabled for CAPWAP control and data tunnels, management and service data
packets will be encrypted using DTLS before being transmitted
A. true
B. false
69. A radio of an AP can only work in either direct or tunnel forwarding mode
A. True
B. False
70. In N+1 backup of ACs, the AP status switchover is slow and is triggered only when CAPWAP link
disconnection timeout is detected. After the AP status is switched, STAs do not need to go offline
and online again.
A. True
HCPP-IP Network

B. False
71. To deploy a large number of APs in a scenario where channel overlapping is inevitable, you can
lower the transmit power of the APs to reduce interference
A. True
B. False
72. A microwave oven may interfere with WLAN signals when in use
A. true
B. false
73. iMaster NCE-Fabric can implement cross-tenant VPC interconnection
A. True
B. False
74. In email-based deployment, also called URL-based deployment, a network administrator
completes the deployment on iMaster NCE, which then automatically generates a deployment
email and sends the email to the specified mailbox. The deployment email contains a URL that
provides the deployment information. After receiving the deployment email to start the
deployment process, after which devices are automatically deployed.
A. True
B. False
75. iMaster NCE-Fabric is the cloud management platform in Huawei’s cloud DCN solution.
A. True
B. False
76. A student in school C reported persistent failures to access the WLAN. Which of the following
CampusInsight functions can be used to locate this fault?
A. Protocol trace
B. Quality evaluation system
C. Performance experience
D. Telemetry
77. In the Huawei public cloud scenario for the CloudCampus solution, which of the following is not
the responsibility of the platform operator?
A. Performing cloud platform O&M
B. Managing MSPs
C. Collecting statistics on the number of devices and services on the entire network
D. Initiating a request for managed services (construction or maintenance)
78. In the CloudCampus public cloud deployment scenario, which of the following roles can authorize
other roles to manage the network on their behalf?
HCPP-IP Network

A. Tenant
B. MSP
C. Platform operator
D. End user
79. Which of the following APs supports a maximum of 16T16R antennas?
A. Aruba AP515
B. AirEngine 8760-X1-PRO
C. Ruckus T750
D. C9115AX1-K
80. Which of the following statements is false about using VXLAN as the overlay technology in Huawei
CloudFabric solution?
A. A VTEP that performs encapsulation is called a VNI
B. VXLAN expands the number of subnets to 16 million and supports multi-tenancy
C. VXLAN uses ECMP on the underlay network to improve network forwarding performance
D. A VXLAN network is built based on UDP
81. In the distributed network overlay, which of the following networking modes is not supported by
a firewall?
A. The firewall is connected to the service leaf node in bypass mode
B. The firewall is connected to the border leaf node in bypass mode
C. The firewall is connected to the service leaf node in inline mode
D. The firewall is connected to the border leaf node in inline mode
82. Which of the following statements about dual-link backup networking is false?
A. Dual link backup provides high reliability between key network nodes to ensure network
reliability and service stability
B. The standby AC must always be powered on
C. The first link established between APs and the AC becomes the active link
D. The service configuration on the active and standby ACs must be the same
83. Which of the following statements about the WLAN roaming traffic forwarding model is true?
A. In direct and tunnel forwarding modes, after Layer 2 roaming is completed, traffic is forwarded to
the home agent through a CAPWAP tunnel
B. In direct forwarding mode, after Layer 2 roaming is completed, traffic is directly forwarded by the
FAP without passing through the FAC.
HCPP-IP Network

C. By default, in Layer 3 roaming + direct forwarding mode traffic is directly forwarded to the upper-
layer network after returning to the HAC
D. In Layer 3 roaming + tunnel forwarding mode, traffic forwarded to the upper layer network
passes through the HAP after returning to the HAC
84. Which off the following statements about the configuration for an AC’s mobility group is false?
A. After an AC is configured as a mobility server, it is added to the mobility group by default and can
manage other ACs in the group
B. An AC functioning as a mobility server manages other ACs through CAPWAP tunnels
C. The mobility server is a logical role, and any physical AC can be configured as mobility server
D. Each member AC must have a mobility server specified
85. Which of the following is the wireless communication process in which STAs may switch to the
channel of another AP due to weak signal strength and high error rate?
A. Association
B. Reassociation
C. Roaming
D. Load balancing
86. Which of the following roaming optimization technologies can resolve terminal stickiness?
A. PMK fast roaming
B. 802.11r fast roaming
C. Smart roaming
D. Layer 3 roaming
87. which of the following wireless protocols cannot work on the 2.4 GHz frequency band?
A. IEEE 802.11g
B. IEEE 802.11n
C. IEEE 802.11ax
D. IEEE 802.11ac
88. Which of the following software or hardware server access modes is not supported by the
CloudFabric solution?
A. BM
B. VM
C. Kubernetes
D. Container
HCPP-IP Network

89. Which of the following statements correctly describes the operation procedure of the WLAN
planner?
A. Import a drawing -> create a project -> set environment parameters -> deploy APs -> simulate
signals
B. create a project -> Import a drawing -> set environment parameters -> deploy APs -> simulate
signals
C. Import a drawing -> create a project -> deploy APs -> set environment parameters -> simulate
signals
D. create a project -> Import a drawing -> deploy APs -> set environment parameters -> simulate
signals

MULTIPLE CHOICE
90. Which of the following modes can be used to identify and analyze connectivity issues through the
clustering algorithm of iMaster NCE-CampusInsight?
A. AC/AP
B. Vendor
C. SSID
D. Client
91. Which of the following statements are true about upgrading cloud managed devices?
A. They can be upgraded in batches on the cloud management platform
B. System software packages are downloaded in encrypted mode
C. System software packages are downloaded without encryption
D. System software package download can be resumed after being paused
92. In the IoT field, Huawei WLAN builds a pipe-based technology platform and ecosystem to fully
leverage the strengths of IoT partners, implement multi-network convergence, and maximize
benefits for customers. Which of the following are the advantages of Huawei WLAN?
A. Wi-Fi and IoT convergence
B. Site design and power supply solutions
C. Site locations and communication channels provided by APs
D. Unified IoT card management on iMaster NCE
93. Which of the following can be used to manage cloud managed devices that have been
disconnected from iMaster NCE?
A. Console port
B. STelnet
HCPP-IP Network

C. Web system
D. Management SSID
94. What are the advantages of Huawei AirEngine 8760-X1-PRO over Cisco Catalyst 9130AXI/AXE?
A. Higher air interface speeds
B. Smart antennas
C. Up to 16 spatial streams
D. Uplink 10GE electrical ports
95. Which of the following statements are true about the high design of firewalls?
A. Service leaf nodes constitute active-active gateway groups. Each firewall is dual-homed to the
service leaf nodes, and service leaf nodes are connected to firewalls through M-LAG interfaces.
B. If any link between the active firewall and a service leaf node is faulty, the M-LAG member
interface goes Down, and the dual-homing mode changes to single-homing mode. In this case, an
active/standby firewall switchover is performed.
C. After the active/standby switchover, the standby firewall sends gratuitous ARP packets to trigger
the update of forwarding entries on service leaf nodes and divert traffic to the standby firewall
D. It is recommended that firewalls be deployed in hot standby mode
96. Which of the following statements are true?
A. Far APs work independently and require separate configurations. They provide only simple
functionality and are cost effective
B. Fat APs need to work with an AC and are managed and configured by the AC in a unified manner
C. APs working in cloud mode cannot be managed by an AC
D. iMaster NCE can be used to manage an AC that manages Fit APs
97. which of the following statements about the AC discovery phase during CAPWAP tunnel
establishment are true?
A. On a Layer 3 WLAN, an AP can discover ACs by broadcasting Discovery messages
B. On a Layer 2 WLAN, an AP can discover ACs using DHCP Option 43
C. An AP can have the IP addresses of ACs pre-configured
D. An AC can have the MAC address of an AP pre-configured so that the AP can discover the AC
through ARP
98. Which of the following methods can be used to control the converge area of an AP?
A. Adjust the antenna angle of an AP
B. Adjust the transmit power of an AP
HCPP-IP Network

C. Adjusting the power supply of an AP

D. Adjusting the access bandwidth of an AP
99. Which of the following obstacles may greatly attenuate radio signals and require special attention
during site survey?
A. Metal
B. Common glass
C. Reinforced concrete
D. Glazed ceramic wall
100. Which of the following statements are true about the access layer design of the CloudCampus
Solution that is applied to small- and medium-sized campus networks?
A. Access switch models are selected based on the number of APs to be connected and whether PoE
is required
B. In small-scale sites, such as small stores, APs and egress devices must be deployed to provide
WLAN coverage. APs cannot directly connect to egress links and do not support NAT
C. For large-scale networks in medium-sized shopping malls, supermarkets, and primary/secondary
education campuses, stack networking is recommended at the access layer. A single device can
be used at the access layer if it will provide sufficient access for downstream terminals. When
aggregation or core switches are stacked, it is recommended that Eth-Trunk interfaces be used to
connect to them. Multiple APs need to be deployed and a PoE LAN switch is used to increase the
number of APs to be connected.
D. As a switch is selected according to the following formula: Number of connected APs x AP power
≤ Power provided by the PoE switch, it is important to select PoE switch models with power
supplies sufficient for the model and quantity of APs used.
101. Which of the following statements about the virtualization computing management platform
are true?
A. It can virtualize and run one or more VMs on a physical machine
B. It effectively improves the utilization of computer hardware resources
C. It can allocate logical resources, such as memory, CPU, and disk resources, based on VM
configurations
D. It translates service requirements into logical network models and network configurations, and
automatically delivers them to physical devices in batches