Romblon State University

College of Engineering and Technology

Department of Electrical Engineering

EE 4121- EE Correlation (ESAS)

Name:______________________________ Date:_________________
Year/Block:__________________________ Score:_________________

ELECTRICAL ENGINEERING AND ALLIED SUBJECTS

INSTRUCTION: Select the correct answer for each of the following questions. Mark only one
answer for each item by shading the box corresponding to the letter of your choice on
the answer sheet provided. STRICTLY NO ERASURE ALLOWED.

MULTIPLE CHOICE:
1. What law states that for all adiabatic processes between two specified states of a closed
system, the net work done is the same regardless of the nature of the closed system and the
details of the process?
a. Fourth Law of Thermodynamics
b. First Law of Thermodynamics
c. Second Law of Thermodynamics
d. Third Law of Thermodynamics

2. The amount of property in which a willing buyer will pay to a willing seller for the property
when neither one is under the compulsion to buy nor sell is called _______ value?
a. Goodwill b. Second-Hand c. market d. Fair

3. An electric heater uses 8.0 A. when connected across the 220V Determine its resistance.
a. 32.5 ohm b. 27.5 ohm c. 25 ohm d. 30 ohm

4. If you are appointed as a division manager, which of he following task is MOST likely you will
do?
a. Determine the resourced needed
b. Develop strategies and tactics
c. Set a standard
d. Set goals

5. A parity bit is also called _________ is an extra bit attached to the end of a byte for purposes of checking for
accuracy.
a. chip size b. silicon type c. check bit d. RAM capacity

6. ___________ two way parallel path connecting processors and memory containing addresses
a. Buffer b. Control Bus c. Cache memory d. Address Bus

7. Steels that are used for axles, gears, and similar parts requiring medium to high hardness and high strength are
known as?
a. Medium-carbon steel b. Very High-carbon steel c. Low-carbon steel d. High-carbon steel

8. The effect of aluminum in cast iron is to?

A. increase hardness above 0.5% C. affect the machinability , ductility, and shrinkage depending on form
B. deoxidize molten cast iron D. reduce hardness by combining with sulfur below 0.5 %

9. The number 12 base 8 is equivalent to decimal

a. 20 b. 4 c. 10 d. 12

10. What is the maximum torque that can be applied to a 1 inch diameter shaft with a maximum stress of 8000 psi?
a. 1200 in-lb b. 1500 in-lb c. 1570 in-lb d. 2000 in-lb

11. What physical property of a material refers to the amount of weight gain (%) experienced in a polymer after
immersion in water for a specified length of time under a controlled environment?
A. Dielectric strength B. Electric resistivity C. Water absorption D. Thermal conductivity

12. What physical property of a material that refers to the rate of heat flow per unit time in a homogenous material
under steady-state conditions per unit are, per unit temperature gradient in a direction perpendicular to area?
A. Thermal expansion B. Thermal conductivity C. Heat distortion temperature D. Water absorption
13. The force necessary to punch a ½ ” diameter hole through ½ ” plate steel ( ultimate strength of 43,000 psi) is
approximately:
a. 4220 pounds b. 34,000 pounds c. 56,000 pounds d. 68,000 pounds

14. A 2 foot diameter cylindrical tank with 0.125 ” thick walls is constructed with spherical ends. If the stress is to be
kept below 12,000 psi , what is the maximum pressure allowed in the tank?
a. 250 psi b. 150 psi c. 300 psi d. 125 psi

15. YZ Corporation manufactures bookcases that it sells for P 65.00 each. It cost XYZ P35,000 per year to operate its
plant. The sum includes rent, depreciation charges on equipment, and salary payments. If the cost to produce one
bookcase is P50.00, how much cases must be sold each year for XYZ to avoid taking a loss?
a. 2334 cases b. 539 cases c. 750 cases d. 2333 cases

16. Qualifications of applicants for registration as PEE who were Assistant/Associate EE under RA 184 is Rule ____
of RA 7920.
a. 13 b. 15 c. 14 d. 12

17. The following are primary alloying ingredients of Group H steel except:
A. Molybdenum B. Tungsten C. Cobalt D. Chromium

18. A sum of P1,000 is invested now and left for 8 years, at which time the principal is withdrawn. The interest that
has accrued is left for another eight years. If the effective annual interest rate is 5%, what will be the withdrawal
amount at the end of the 16th year?
a. P706.00 b. P500.00 c. P774.00 d. P799.00

19. What is defined as an intimate mechanical mixture of two or more phases having a definite composition and a
definite temperature of transformation within the solid state?
A. Pearlite B. Eutectoid C. Austernite D. Delta solid solution

20. An asset is purchased for P500,000. The salvage value in 25 years is P100,000. What are the depreciation in the
first three years using straight line method?
a. P48,000.00 b. P24,000.00 c. P32,000.00 d. P16,000.00

21. What typical penetrator is used in Brinell hardness test?

A. 10 mm ball B. 120° diamond (brale) C. 1.6 mm diameter ball D. 20°needle

22. An aggregate of individual formed for the purpose of conducting a business and recognized by law as a fictitious
person is called
A. Stockholder B. Corporation C. Investor D. Partnership

23. Find the speed of sound in 32oF water if the compressibility is 3.4 x 10 to the negative 6 psi.?
A. 4674 ft/sec B. 4764 ft/sec C. 4584 ft/sec D. 4854 ft/sec

24. Given the following bond distances: C – C at 1.54R, C-H at 1.07R & C-C1 at 1.77R, calculate the atomic radii of
C, on the supposition that atoms are spheres which contact each other.
A. 0.88 B. 0.13 C. 0.77 D. 0.99

25. ______ a temporary holding file that holds all changes to be made to the master file, addition, deletions, revisions.
A. Master upgrade B. Processing C. Transaction D. Data upgrade

26. A high strength steel band saw , 20 mm wide and 0.8 mm thick runs over a pulley 600 mm in diameter. What
minimum diameter pulleys can be used without exceeding a flexural stress of 400 MPa? Use E = 200 Gpa.
A. 250 cm B. 325 m C. 400 mm D. 150 in.

27. Which of the following is The Ideal Gas Law?

A. V/T = k B. P1/T1 = P2/T2 C. V = k x 1/P D. PV = nRT

28. A hockey rubber ball leaves a player’s stick with a velocity of 30 ft/sec and slides 120 ft. Before coming to rest,
find the coefficient of friction between the rubber ball and the ice?
A. 0.217 B. 0.317 C. 0.127 D. 0.117

29. At a certain point in a horizontal pipeline, a gauge pressure is at 0.5 x 10 to +5 power n/mtr sq. At another point, a
gauge pressure is at 0.3 x 10 to +5 power n/mtr sq. if the areas of the pipe at these points are 20 cm sq and 10 cm
sq. respectively, compute the number of cubic meters of water which will flow across in any of the cross section
of the pipe per minute?
A. 0.75 cm/min B. 0.438 cm/min C. 0.61 cm/min D. 0.83 cm/min
30. What is the maximum height that a vacuum pump can lift 60 ft water if the atmospheric pressure is 14.6 psia and
local gravity is 28 ft/sec2 ? Vapor pressure of water at 60oF is 0.2563 psia.
A. 25.07 ft B. 47.07 ft C. 38.07 ft D. 56.07 ft

31. The entrance enthalpy, velocity and height of an open system receiving mass at the rate of 5 lbs/sec. are 1000
BTU/lb, 100 ft/sec. and 100 ft., respectively. 50 BTU/sec are lost to the surroundings. The exit enthalpy, velocity
and height are 1020 BTU/lb., 50 ft/sec and 0 ft., respectively. What is the input horsepower?
A. 210.3 hp B. 250 hp C. 280 hp D. 200 hp.

32. How many BTU are needed to isothermally compress 4 lbs at 240 deg. F of air to twice the original pressure?
A. + 140 BTU B. – 150 BTU C. – 132 BTU D. + 160 BTU

33. The chrome-molybdenum steels contain how many percent of molybdenum?

A. 0.10 B. 0.20 C. 0.30 D. 0.40

34. In the Reexamination of the Failed Subjects in the examination for Registered Electrical
Engineer, a applicant shall be allowed to retake _______ times, only the subject/s in which he
has obtained a grade below fifty percent (50%).
a. Three b. no limit c. four d. five

35. Which of the following is the fastest method to transfer data wirelessly?
a. Standard infrared b. Bluetooth c. 802.11 d. General Packet Radio System

36. What is the kinetic energy of the world-class sprinter with a weight of 80 kgs ad speed of
10m/s?
a. 3.2kJ b. 3.6kJ c. 4.8kJ d. 4.0kJ

37. What is the equivalent unit of “pascal”?

a. N/m b. N-m c. N-m2 d. N/m2

38. Which of the following principle of thermodynamics cycle that steam engine operates?
a. Carnot b. diesel c. brayton d. stirling

39. Which of these location/s described partially protected locations under canopies, marques,
roofed and open porches subject to moderate degree of moisture in the PEC 1?
a. Dry b. Wet c. Moist d. Damp

40. In estimating the loading of the branch circuit, what loading shall be used for each
receptacle?
a. 200 VA b. 180 VA c. 150 VA d. 160 VA

41. What is a system or circuit conductor that is intentionally grounded based on PEC 1?
a. Grounding Electrode
b. Equipment Grounding Electrode
c. Grounded Electrode
d. Neutral Conductor

42. The number 100101 base 2 is equivalent to octal ________.

a. 25 b. 45 c. 37 d. 54

43. A silicon solar cell of dimension 1 x 2 cm produces a current of 56 mA at 0.45V when

illuminated by sunlight of intensity 1000W/m 2. What is the efficiency of the cell?
a. 16.20% b. 14.30% c. 12.60% d. 13.40%

44. Mr. Juan Dela Cruz drives 120 km at 100 kph and 120 km at 90 kph. What is the average
speed of Mr. Dela Cruz on this trip in kph?
a. 93.5 b. 94.7 c. 85.8 d. 82.3

45. Which of the following refers to the branch of computer science that is concerned with
making computers “behave” and “think” like humans?
a. Intelligence b. Artificial Intelligence c. Neutral Network d. Robotics Science

46. What is the present worth of two P 100 payments at the end of the third ad fourth years if
the annual interest rate is 8%?
a. P 120 b. P 153 c. P 122 d. P 160
47. An airplane accelerates down a runway at 3.20m/s square for 32.8 s until it finally lifts off
the ground. Calculate the distance in meters travelled before takeoff.
a. 152.48 b. 1721.34 c. 1679.36 d. 1524.80

48. The chrome-vanadium steels contain how many percent of vanadium?

A. 0.15 to 0.30 B. 0.05 to 0.15 C. 0.30 to 0.45 D. 0.45 to 0.60

49. Manganese steel usually contains how many percent of manganese?

A. 1 to 5 B. 5 to 10 C. 11 to 14 D. 14 to 18

50. The wear-resistance of this material is attributed to its ability to _______, that is, the hardness is increased greatly
when the steel is cold worked.
A. cold harden B. stress harden C. cool-temperature D. strain harden
51. The special chrome steels of the stainless variety contain how many percent of chromium?
A. 4 to 8 B. 9 to 10 C. 11 to 17 D. 17 to 21

52. What refers to the application of any process whereby the surface of steel is altered so that it will become hard?
A. Caburizing B. Casehardening C. Annealing D. Surfacehardening

53. A man borrowed P500,000.00 from a bank and agreed to pay the loan at the end of a month. The bank discounted
the loan and gave him P450,000 in each. What is the rate of discount?
a. 15% b. 10% c. 12% d. 20%
54. A number 10 exponent google or 10google is called
A. milligoogle B. centigoogle C. googleplex D. myriad

55. An asset is purchased for P9,000.00. Its estimated life is ten years after which it will be sold for P1,000.00. find
the book value during the first year if the sum-of-the-years-digit (SOYD)depreciation is used?
a. P8,000.00 b. P6,500.00 c. P7,545.00 d. P6,000.00

56. One section is equivalent to 1 ______?

A. square foot B. square meter C. square nautical mile D. Square statute mile

57. The pressure of 1 torr is equivalent to how many pascals?

A. 100 B. 133.3 C. 166.7 D. 200

58. Worth of the property as shown in the accounting records of an enterprise?

A. Fair value B. Market Value C. Salvage Value D. Book Value

59. Parties whose consent or signature in a contract is not considered intelligent

A. Dead person B. Senior Citizen C. Demented person D. Minors

60. It is defined to be the capacity of a commodity to satisfy human want:

A. Discount B. Luxury C. Necessity D. Utility

61. Sec 2(a)(3) Art I of RA 7920 is:

a. Supervision of erection, installation, testing and commissioning of power plants
b. Supervision of operation and maintenance of electric equipment
c. Supervision of the manufacture and repair of electrical equipment
d. Taking charge of sale and distribution of electrical equipment and systems.

62. The maintenance cost of a machine this year is expected to be P1,000.00. The cost will increase P200.00 each
year for the subsequent 9 years. The interest is 15% compounded annually. What is the approximate worth of
maintenance for the machine over the full 10 years?
a. P4,814.67 b. P4,481.76 c. P8,414.67 d. P4,418.67

63. What does CPE means:

a. Commission on Professional Education
b. Continuing Practical Electricity
c. Committee for Professional Engineer
d. Continuing Professional Education

64. What physical property of a material refers to the highest potential difference (voltage) that an insulting material
of given thickness can withstand for a specified time without occurrence of electrical breakdown through its bulk?
A. Thermal expansion B. Conductivity C. Dielectric strength D. Electrical resistivity

65. What physical property of a material refers to the ratio of the amount of heat required to raise the temperature of a
unit mass of a substance 1 degree to the heat required to raise the same mass of water to 1 degree.
A. Specific heat B. Latent heat C. Heat of fusion D. Heat of fission
66. What physical property of a material refers to the temperature at which a polymer under a specified load shows a
specified amount of deflection?
A. Curie temperature B. Specific heat C. Heat distortion temperature D. Thermal conductivity

67. Sec 17 (b) of Article III : Examination and Registration, Qualification for Registered Electrical Engineer states
that an applicant is at least be ____ years of age.
a. 21 b. 23 c. 24 d. 25

68. A parent on the day the child is born wishes to determine what lump sum would have to be paid into an account
bearing interest at 5% compounded annually, in order to withdraw P20,000 each on the child’s 18th , 19th, 20th,
21st birthdays?
a. P35,941.73 b. P33,941.73 c. P30,941.73 d. P25,941.73

69. Rule 7 RA 7920 is?

a. Enforcement and Execution b. Assignment of Duties
c. Official business with the commission d. Promulgation of Decisions

70. What group of steels are water hardened tool steel?

a. Group S b. Group O c. Group W d. Group T

71. Which of the following classes of mass memory devices used a laser beam to write and read
onto a specified coated disk?
a. Non-volatile memory b. RAM c. ROM d. Optical Disk Memory

72. Find the principal amount if the amount of interest at the end of two years is P 4,000 for a
simple interest of 6.25% per annum.
a. P 36,000 b. P 32,000 c. P 27,000 d. P 23,000

73. A bank charges 6% simple interest on a P 25,000 loan. How much will be repaid if the loan is
paid back in one lump sum after five years?
a. P 30,875 b. P 32,750 c. P 32,500 d. P 31,250

74. The three moment equation may be used to analyze _______.

a. An axially end-loaded beam c. a continuous beam
b. A beam loaded at the third points d. a step tapered column

75. What ca you say about the following statement regarding centrifugal pumps? “The discharge
of the centrifugal pumps can be throlled without the building up of an excessive pressure or
overloading its driving unit.”
I. True
II. False
III. Either True or False
IV. True for reciprocating pumps
a. II b. I c. III d. IV

76. An investment X dollars is made at the end of each year for 3 years, at an interest rate of 9%
per year compounded annually. What will the dollar value of the total investment be upon
the deposit of the third payment?
a. 3.582X b. 3.278X c. 1.378X d. 2.783X

77. Pedro borrowed P 20,000.00 from a bank with 15% interest compounded semi-annually,
what is the total amount to be repaid at the end of two years?
a. P 25,947.80 b. P 26,709.38 c. P 28,712.59 d. P 24,845.94

78. A liquid pesticide has a density of 1.67 g/ml. Find the mass of the liquid in kg for a full 20-L
container.
a. 35.7 b. 34.5 c. 32.6 d. 33.4

79. In a spreadsheet (EXCEL), the number in cell A2 is set to 2. The cell B2 is set to A2*4/$A$2,
where $ indicates the absolute cell address. This formula is copied into cells C2 and D2 What
is the value shown in cell D2?
a. 8 b. 2 c. 4 d. 16

80. An electrical equipment is purchased at a cost of P 10,000. It has a 10 year life and a salvage
of P 500. What is the book value of the equipment after 3 years using straight line
depreciation?
 a. P 7,100 b. P 7,200 c. P 7,150 d. P 7,250

81. Which of the following is correct when a vapor condensed to a liquid?

a. Its temperature rises c. Its temperature falls
b. It gives off internal energy d. Its internal energy increases

82. Determine the atmospheric pressure (in kPa) at a location where the barometric reading is
740mmHg and the gravitational acceleration is g=9.81 m/sec squared. Assume that the
temperature of mercury to be 10 deg C, at which its density is 13,570 kg/cu.m.
a. 111.58 b. 98.51 c. 89.47 d. 99.82

83. In the Reexamination of the Failed Subjects in the examination for Registered Electrical
Engineer, a applicant shall be allowed to retake _______ times, only the subject/s in which he
has obtained a grade below fifty percent (50%).
b. Three b. no limit c. four d. five

84. Which of the following is the fastest method to transfer data wirelessly?
b. Standard infrared b. Bluetooth c. 802.11 d. General Packet Radio System

85. What is the kinetic energy of the world-class sprinter with a weight of 80 kgs ad speed of
10m/s?
b. 3.2kJ b. 3.6kJ c. 4.8kJ d. 4.0kJ

86. What is the equivalent unit of “pascal”?

b. N/m b. N-m c. N-m2 d. N/m2

87. Which of the following principle of thermodynamics cycle that steam engine operates?
b. Carnot b. diesel c. brayton d. stirling

88. Which of these location/s described partially protected locations under canopies, marques,
roofed and open porches subject to moderate degree of moisture in the PEC 1?
b. Dry b. Wet c. Moist d. Damp
89. A function of an engineer where the engineer is assigned to manage groups of people
performing specific tasks.
a. Teaching b. Government c. Management d. Consulting

90. Defined as the process of identifying and choosing alternative courses of action in a manner
appropriate to the demands of the situation.
a. Decision Making b. Engineering Management c. Initiative d. Problem solving

91. Refers to the management function that involves anticipating future trends and determining
the best strategies and tactics to achieve organizational objectives.
a. Management b. Planning c. Organizing d. Supervision

92. If air is at pressure, p, of 135 Pa, ad at a temperature, T, of 440K, what is most early the
specific volume, ν? (Air’s specific gas constant is 𝑅 = 88.81 𝐽/𝑘𝑔 − 𝐾. )
a. 110 m3 /kg b. 130 m3 /kg c. 290 m3 /kg d. 300 m3/kg

93. The Philippine Electrical Code Part 1 2009 was based o the National Electrical Code 2005
while the Philippine Electrical Code Part 2 2017 Edition was based on the National Electrical
Code _______.
a. 2017 b. 2011 c. 2008 d. 2014

94. HTTP:// is an identifier that appears at the beginning of most Web page. What does the
HTTP stand for?
a. Hypertime Text Process
b. Hypertext Transfer Protocol
c. Hypertext Transmission Process
d. Hypertext Time Protocol

95. Find the MW of HNO3 in g/mole.

a. 72 b. 61 c. 73 d. 63

96. Mr. Cruz borrowed P 20 000 from bank with 15% interest per annum, find the total amount
to be repaid at the end of two years.
a. P 24,664.75 b. P 23,000.00 c. P 25, 720.90 d. P 26,450.00
 97. The process of outsmarting the search engine?
a. Google Fooling c. Rank Enhancement
b. Search Engine Optimization d. Search Engine Hacking

98. As a projectile is thrown upward moves in its parabolic path, at what point along its path are
the velocity and acceleration vectors for the projectile perpendicular to each other.
a. the launch point b. the lowest point c. nowhere d. the highest point

99. If the velocity of the flow in a 2-cm radius hose is 1.2 m/s, what is the output velocity in a
0.5 cm radius jet issuing from a nozzle attached at the end of the pipe?
a. 0.192m/s b. 4.8m/s c. 0.3 m/s d. 0.075m/s

100. What is the old Electrical Engineering Law?

a. RA 814 b. RA 184 c. RA 9136 d. RA 7920

Compiled by:

Engr. Jaybie M. Tamayo

Noted by:

Engr. Jay T. Oliveros, RME