JAPANESE

INDUSTRIAL
STANDARD
Translated and Published by
Japanese Standards Association

JIS G 3192 : 2021

(JISF)
Dimensions, shape, mass and
permissible variations of hot rolled
steel sections

ICS 77.140.70
Reference number : JIS G 3192 : 2021 (E)

PROTECTED BY COPYRIGHT 23 S
G 3192 : 2021

Date of Establishment: 1954-07-30

Date of Revision: 2021-04-20
Date of Public Notice in Official Gazette: 2021-04-20
Developed by: The Japan Iron and Steel Federation
Investigated by: The Japan Iron and Steel Federation, Standardization
Center

JIS G 3192 : 2021, First English edition published in 2021-12

Translated and published by: Japanese Standards Association

Mita MT Building, 3-13-12, Mita, Minato-ku, Tokyo, 108-0073 JAPAN

In the event of any doubts arising as to the contents,

the original JIS is to be the final authority.

 JSA 2021
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized
in any form or by any means, electronic or mechanical, including photocopying and microfilm, without
permission in writing from the publisher.

Printed in Japan HN

PROTECTED BY COPYRIGHT
 G 3192 : 2021

Contents

Page

Introduction ······························································································· 1
1 Scope ································································································ 1
2 Normative references··········································································· 2
3 Terms and definitions ·········································································· 2
4 Classification and sectional shape ·························································· 2
5 Expression of dimensions and marking ··················································· 3
6 Standard dimensions ··········································································· 3
7 Shapes and dimensional tolerances ························································ 4
8 Mass································································································· 4
9 Tolerances on mass ············································································· 4
10 Appearance ························································································ 5
Annex JA (informative) Comparison table between JIS and corresponding
International Standards············································38

(i)
PROTECTED BY COPYRIGHT
G 3192 : 2021

Foreword

This Japanese Industrial Standard has been revised by the Minister of

Economy, Trade and Industry based on the provision of Article 14, para-
graph (1) of the Industrial Standardization Act applied mutatis mutandis
pursuant to the provision of Article 16 of the said Act in response to a
proposal for revision of Japanese Industrial Standard with a draft being
attached, submitted by The Japan Iron and Steel Federation (JISF), an
accredited standards development organization. This edition replaces the
previous edition (JIS G 3192 : 2014), which has been technically revised.
This JIS document is protected by the Copyright Act.
Attention is drawn to the possibility that some parts of this Standard
may conflict with patent rights, published patent application or utility
model rights. The relevant Minister is not responsible for identifying any
of such patent rights, published patent application or utility model rights.

(ii)
PROTECTED BY COPYRIGHT
JAPANESE INDUSTRIAL STANDARD JIS G 3192 : 2021

Dimensions, shape, mass and permissible variations of hot

rolled steel sections

Introduction
This Japanese Industrial Standard has been prepared based on ISO 657-1 : 1989,
Edition 1, ISO 657-2 : 1989, Edition 1, ISO 657-5 : 1976, Edition 1, ISO 657-11 : 1980,
Edition 1, ISO 657-15 : 1980, Edition 1, ISO 657-18 : 1980, Edition 1, ISO 657-19 : 1980,
Edition 1 and ISO 657-21 : 1983, Edition 1 with some modifications of the technical
contents.
The vertical lines on both sides and dotted underlines indicate changes from the cor-
responding International Standard. A list of modifications with the explanations is
given in Annex JA.

1 Scope
This Standard specifies the appearance, shapes and permissible variations thereof,
and the dimensions, mass and their tolerances of hot rolled steel sections (hereafter
referred to as steel sections).
The application of this Standard shall be as specified in each product standard.
NOTE The International Standards corresponding to this Standard and the
symbol of degree of correspondence are as follows.
ISO 657-1 : 1989 Hot-rolled steel sections — Part 1 : Equal-leg angles－
Dimensions
ISO 657-2 : 1989 Hot-rolled steel sections — Part 2 : Unequal-leg an-
gles－Dimensions
ISO 657-5 : 1976 Hot-rolled steel sections — Part 5 : Equal-leg angles
and unequal-leg angles — Tolerances for metric and inch series
ISO 657-11 : 1980 Hot-rolled steel sections — Part 11 : Sloping flange
channel sections (Metric series) — Dimensions and sectional properties
ISO 657-15 : 1980 Hot-rolled steel sections — Part 15 : Sloping flange
beam sections (Metric series) — Dimensions and sectional properties
ISO 657-18 : 1980 Hot-rolled steel sections — Part 18 : L sections for
shipbuilding (metric series) — Dimensions, sectional properties and tol-
erances
ISO 657-19 : 1980 Hot-rolled steel sections — Part 19 : Bulb flats (met-
ric series) — Dimensions, sectional properties and tolerances
ISO 657-21 : 1983 Hot-rolled steel sections — Part 21 : T-sections with
equal depth and flange width — Dimensions (overall evaluation : MOD)
In addition, symbols which denote the degree of correspondence in the
contents between the relevant International Standard and JIS are IDT

PROTECTED BY COPYRIGHT