File Name: MEITRACK Parameter Editor Creator: Cavana Cheung

Project: MVT340/MVT380/MVT100/ Creation Date: 2010-03-25

MVT600/T1/MT90/MT88/MT80i Update: 2011-08-01
Sub Project: Parameter Editor User Guide Page: 1 of 13
Revision: V1.06 Confidential: External Documentation

MEITRACK® Parameter Editor

User Guide

Copyright © 2010 Shenzhen Meiligao Electronics Co., Ltd. All rights reserved.
 File Name: MEITRACK Parameter Editor Creator: Cavana Cheung
Project: MVT340/MVT380/MVT100/ Creation Date: 2010-03-25
MVT600/T1/MT90/MT88/MT80i Update: 2011-08-01
Sub Project: Parameter Editor User Guide Page: 2 of 13
Revision: V1.06 Confidential: External Documentation

Contents

1. Introduction ......................................................................................................3
2. Hardware and Software Required .........................................................................3
3. Installation and Connection .................................................................................3
4. Configuration.....................................................................................................4
Tab 1: SMS Tracking .................................................................................................5
Tab 2: GPRS Tracking ................................................................................................6
Tap3: Main Settings .................................................................................................8
Tab 4: Geo Fence Settings......................................................................................... 10
Tab 5: Authorization ............................................................................................... 11
Tab 6: SMS Header ................................................................................................ 12
Tap 7: Photo Authorization (only for MVT600) .................................................................. 13
Tool Bar ............................................................................................................ 13

Copyright © 2010 Shenzhen Meiligao Electronics Co., Ltd. All rights reserved.
 File Name: MEITRACK Parameter Editor Creator: Cavana Cheung
Project: MVT340/MVT380/MVT100/ Creation Date: 2010-03-25
MVT600/T1/MT90/MT88/MT80i Update: 2011-08-01
Sub Project: Parameter Editor User Guide Page: 3 of 13
Revision: V1.06 Confidential: External Documentation

1. Introduction

MEITRACK Parameter Editor is used to configure MEITRACK’S GPS Tracker MVT100, MVT340,
MVT380, MVT600, T1, MT90, MT88 and MT80i.

2. Hardware and Software Required

 A personal computer or laptop with Windows XP, Windows Vista, or Windows 7;

 One USB Data Cable;

 Driver for USB Data Cable;

 MEITRACK® Parameter Editor.

3. Installation and Connection

Run ‘PL2303_Prolific_DriverInstaller’ to install the driver for the USB data cable.
Note: PL2303_Prolific_DriverInstaller is in the folder ‘USB-232 Driver’ in the CD.

Connect the USB data cable with your computer.

Open Device Manager (Device Manager is under Control Panel\System and Security\System). You
can then find ‘Prolific USB-to-Serial Comm Port’ as the following picture shows.

Copyright © 2010 Shenzhen Meiligao Electronics Co., Ltd. All rights reserved.
 File Name: MEITRACK Parameter Editor Creator: Cavana Cheung
Project: MVT340/MVT380/MVT100/ Creation Date: 2010-03-25
MVT600/T1/MT90/MT88/MT80i Update: 2011-08-01
Sub Project: Parameter Editor User Guide Page: 4 of 13
Revision: V1.06 Confidential: External Documentation

Note: Remember this Com number. It needs to be input in MEITRACK Parameter Editor. It is COM3
in this example and it would be COM4 or COM5…in your computer.

4. Configuration

Connect the tracker to your computer by the USB data cable as the below picture shows:

Run ‘MEITRACK Parameter Editor.exe’ and the following configuration window will be opened:

Select the correct Com number according to the Device Manager shows and select tracker’s
model. And then click the ‘Open Port’ button.
Note: MEITRACK Parameter Editor is in the CD. The language will be automatically adjusted to be
the same as your PC operation system’s language. Please use “Ctrl+L” to change the language.

MT80i/MT88/MT90/MVT100/MVT340/MVT380/MVT600/T1: After the tracker is properly

connected with USB Data Cable, you have two ways to make the tracker ready for configuration:
1. Press and hold tracker’s SOS Button (SOS button is connected with the I/O cable) and then
turn on the tracker
2. Turn on the tracker directly

Copyright © 2010 Shenzhen Meiligao Electronics Co., Ltd. All rights reserved.
 File Name: MEITRACK Parameter Editor Creator: Cavana Cheung
Project: MVT340/MVT380/MVT100/ Creation Date: 2010-03-25
MVT600/T1/MT90/MT88/MT80i Update: 2011-08-01
Sub Project: Parameter Editor User Guide Page: 5 of 13
Revision: V1.06 Confidential: External Documentation

After that, all LEDs will be on. Now the tracker is ready for configuration.
Click ‘Read Settings’ button to show the default or previous settings of the tracker and the
following window will pop up:

Tab 1: SMS Tracking

Item Description Applicable Model

User Password SMS password for sending SMS commands and All
defaulted as 0000
Phone Number A phone number to receive SMS location reports. All
SMS Report Track by time interval via SMS. All
Interval Set time interval for SMS location report.
= 0, stop tracking by time interval (default);
= [1,65535], track by interval in minute;
Auto Report = 0, track by interval continuously All
Times = [1,255], set how many times (reports) of SMS from
the tracker with the defined interval.
Read Read current tracker’s settings for above items
Write Write above settings to the tracker.

Copyright © 2010 Shenzhen Meiligao Electronics Co., Ltd. All rights reserved.
 File Name: MEITRACK Parameter Editor Creator: Cavana Cheung
Project: MVT340/MVT380/MVT100/ Creation Date: 2010-03-25
MVT600/T1/MT90/MT88/MT80i Update: 2011-08-01
Sub Project: Parameter Editor User Guide Page: 6 of 13
Revision: V1.06 Confidential: External Documentation

Tab 2: GPRS Tracking

Item Description Applicable Model

GPRS Select TCP/UDP to enable GPRS communication All
GPRS Interval Track by time interval via GPRS. All
Set time interval for GPRS tracking.
Interval is in unit of 10 seconds.
Interval = 0, stop tracking by time interval.
Max time interval = 65535*10 seconds
GPRS Report = 0, track by interval continuously; All
Times = [1,65535], set how many times(reports) from the
tracker with the defined interval.
IP & Port Input server’s IP address and port number. All
Secondary IP & Set the secondary server’s IP address and port All
Port number in case that the first server is down.
APN, APN APN, APN username, APN password: max 32 bytes; All
Username, If no username and password required, leave them
APN Password blank.
Tracker ID Tracker’s IMEI and it is automatically displayed. All
Read Read current tracker’s settings for above items.
Write Write above settings to the tracker.

Copyright © 2010 Shenzhen Meiligao Electronics Co., Ltd. All rights reserved.
 File Name: MEITRACK Parameter Editor Creator: Cavana Cheung
Project: MVT340/MVT380/MVT100/ Creation Date: 2010-03-25
MVT600/T1/MT90/MT88/MT80i Update: 2011-08-01
Sub Project: Parameter Editor User Guide Page: 7 of 13
Revision: V1.06 Confidential: External Documentation

On the Event list, you can select events to be included in the GPRS report message.
Event Descriptions:
Event Description Applicable Model
(if the box is ticked, event will be included in GPRS report)
Input 1 Active Input 1 is active (SOS button is pressed) All
Input 2 Active Input2 is active MVT340/380/600, T1
Input 3 Active Input3 is active MVT380/600, T1
Input 4 Active Input4 is active MVT380
Input 5 Active Input5 is active MVT380
Input 1 Inactive Input 1 is inactive (SOS button is released) All
Input 2 Inactive Input 2 is inactive MVT340/380/600, T1
Input 3 Inactive Input 3 is inactive MVT380/600, T1
Input 4 Inactive Input 4 is inactive MVT380
Input 5 Inactive Input 5 is inactive MVT380
Low Battery Voltage level from internal (backup) battery is All
lower than 3.5V
Low External External power (car battery) is lower than MVT100/340/380/600
Power predefined voltage. T1
You can define voltage in Main Settings.
Speeding Tracker’s speed is over the predefined speed limit. All
You can define speed limit in Main Settings.
Enter Geo-fence Alarm when tracker enters the predefined All
Geo-fence waypoint
Exit Geo-fence Alarm when tracker exits the predefined Geo-fence All
waypoint
You can define waypoints in Geo Fence Settings.
External Power Alarm when external power supply is on or recover MVT100/340/380/600
On T1
External Power Alarm when external power supply if off or cut MVT100/340/380/600
Off T1
No GPS Signal Alarm if the tracker has no GPS fix All
Get GPS Signal Alarm when the tracker gets GPS signal All
Enter Sleep Alarm when the tracker gets into sleep mode All
Exit Sleep Alarm when the tracker wakes up from sleep mode All
You can define sleep mode in Main Settings.
GPS Antenna Cut Alarm when the GPS antenna is disconnected or MVT340/380/600
cut T1
Device Reboot Alarm when the device is reboot All
Impact Alarm when the tracker(with impact sensor) MVT100/380/600, T1
detects impact or crash
Heartbeat Report Turn on heartbeat report All
You can define heartbeat interval in Main Settings.

Copyright © 2010 Shenzhen Meiligao Electronics Co., Ltd. All rights reserved.
 File Name: MEITRACK Parameter Editor Creator: Cavana Cheung
Project: MVT340/MVT380/MVT100/ Creation Date: 2010-03-25
MVT600/T1/MT90/MT88/MT80i Update: 2011-08-01
Sub Project: Parameter Editor User Guide Page: 8 of 13
Revision: V1.06 Confidential: External Documentation

Heading Change Auto report when tracker’s direction changes over All
Report predefined angle
You can define angle degree in Main Settings.
Distance Interval Tracker by distance interval All
Report You can define distance interval in Main Settings.
Tow Alarm Alarm when the tracker trembles for a period of All
time
You can define tow time in Main Settings.
RFID RFID data (MVT600 only) MVT600, T1

Tap3: Main Settings

Item Description Applicable Model

Protocol Auto Event Report (default), or All
Event report needs server’s confirmation by AFF
command
Refer to MEITRACK SMS GPRS Protocol for more
details.
SMS Time Zone Default time of the tracker is GMT. You can use this All
comment to correct it to your local time for SMS
report.

Copyright © 2010 Shenzhen Meiligao Electronics Co., Ltd. All rights reserved.
 File Name: MEITRACK Parameter Editor Creator: Cavana Cheung
Project: MVT340/MVT380/MVT100/ Creation Date: 2010-03-25
MVT600/T1/MT90/MT88/MT80i Update: 2011-08-01
Sub Project: Parameter Editor User Guide Page: 9 of 13
Revision: V1.06 Confidential: External Documentation

= 0, GMT (default);
= [-32768,32767], set time difference in minutes to
GMT.
GPRS Time Zone Default time for GPRS report is GMT. All
= 0, GMT (default);
= [-32768,32767], set time difference in minutes to
GMT.
Distance Set distance interval for SMS/GPRS tracking. All
Interval = 0, stop tracking by distance interval (default);
= [1, 4294967295], set interval in meter
Heading Change When the heading direction of the tracker changes All
Report over the preset degree, a message with location
data will be sent back to the server by GPRS.
= 0, cancel heading change report (default);
= [1,359], set degree of direction change.
Speeding Alarm = 0, cancel speeding alarm (default) All
= [1,255], set speed limit in Km/h
Low External When the external power supply (car battery) is MVT100/340/380/600
Power lower than a predefined voltage, and alarm message T1
will be sent to the mobile phone or server.
Heartbeat = 0, cancel heartbeat report (default); All
Interval = [1,65535], set interval in minute.
Log Interval Set the interval for storing GPS data into tracker’s MT80i/88/90
flash memory. MVT100/380/600
= 0, turn off logging; T1
= [1,65535], set logging interval in second.
GPS Sleep Mode Set sleep mode for tracker’s GPS module All
Power Down Set power down mode when the tracker is inactive All
(stationary) for a period of time.
In Power Down mode, GPS stops working and GSM
enters sleep mode. The tracker stops sending out
messages until it is activated by message, incoming
calls, and movement or input changes.
= 0, turn off power down mode
= [1,255], turn on power down after a specified
period of being inactive in minute.
Tow Alarm = 0, cancel tow alarm (default); MVT100/340/380/600
= [1,255], set period in second. T1
If the tracker trembles over the pre-define period,
an alarm message will be sent to the mobile phone
or server.
LED Off If the box is ticked, all LED lights are off when the All

Copyright © 2010 Shenzhen Meiligao Electronics Co., Ltd. All rights reserved.
 File Name: MEITRACK Parameter Editor Creator: Cavana Cheung
Project: MVT340/MVT380/MVT100/ Creation Date: 2010-03-25
MVT600/T1/MT90/MT88/MT80i Update: 2011-08-01
Sub Project: Parameter Editor User Guide Page: 10 of 13
Revision: V1.06 Confidential: External Documentation

tracker is working.
Buzzer Off Turn off tracker’s buzzer when a call is coming in. MT90
Read Read current tracker’s settings for above items
Write Write above settings to the tracker.

Tab 4: Geo Fence Settings

Item Description
Waypoint Max 8 waypoints can be set for Geo-fence alarm.
Latitude Latitude in decimal degrees of the waypoint center
Longitude Longitude in decimal degrees of the waypoint center.
Radius Radius in meter of the circle
In Alarm Tick to turn on the alarm when the tracker enters the waypoint
Out Alarm Tick to turn on the alarm when the tracker exits the waypoint.
Read Read current tracker’s settings for above items
Write Write above settings to the tracker.
Note: Geo Fence Settings are applicable to all models.

Copyright © 2010 Shenzhen Meiligao Electronics Co., Ltd. All rights reserved.
 File Name: MEITRACK Parameter Editor Creator: Cavana Cheung
Project: MVT340/MVT380/MVT100/ Creation Date: 2010-03-25
MVT600/T1/MT90/MT88/MT80i Update: 2011-08-01
Sub Project: Parameter Editor User Guide Page: 11 of 13
Revision: V1.06 Confidential: External Documentation

Tab 5: Authorization

Item Description
Authorization Phone Number Authorize phone number(s) for receiving SMS reports and
select events to be included in the SMS.
Event Tick to include the event information in the SMS report.
Refer to MEITRACK SMS/GPRS Protocol for more details.

From event descriptions for ‘Input1 Active’ to ‘Tow Alarm’,

please refer to Event Description under Tap 2: GPRS Tracking.

See below for description of other events.

Read Read current tracker’s settings for above items
Write Write above settings to the tracker.

Description of other events

Event Description (if the box is ticked) Applicable Model
Press Input 1 (SOS) Press to call the authorized phone MT80i/88/90,MVT100/340/380/600,

Copyright © 2010 Shenzhen Meiligao Electronics Co., Ltd. All rights reserved.
 File Name: MEITRACK Parameter Editor Creator: Cavana Cheung
Project: MVT340/MVT380/MVT100/ Creation Date: 2010-03-25
MVT600/T1/MT90/MT88/MT80i Update: 2011-08-01
Sub Project: Parameter Editor User Guide Page: 12 of 13
Revision: V1.06 Confidential: External Documentation

to Call number T1
Press Input 2 to Press to call the authorized phone MVT100/340/380/600, T1
Call number
Press Input 3 to Press to call the authorized phone MVT380/600, T1
Call number
Press Input 4 to Press to call the authorized phone MVT380
Call number
Press Input 5 to Press to call the authorized phone MVT380
Call number
Reject Incoming Reject when the authorized phone All
Call calling in
Report Location Report location after the call is All
after Calling in rejected or missed
Auto Answer Auto answer the incoming call for MT80i/88/90,MVT380/600, T1
Incoming Call conversation
Listen-in (voice Auto answer the incoming call for MT80i/88/90,MVT380/600, T1
monitoring) voice monitoring

Tab 6: SMS Header

Description: Set SMS header of each event to be shown in the beginning in the SMS.
For example, you can input ‘SOS’ in the column of ‘Input 1 Active’, once the tracker’s SOS button
is pressed, an SMS with ‘SOS’ will be received.

Copyright © 2010 Shenzhen Meiligao Electronics Co., Ltd. All rights reserved.
 File Name: MEITRACK Parameter Editor Creator: Cavana Cheung
Project: MVT340/MVT380/MVT100/ Creation Date: 2010-03-25
MVT600/T1/MT90/MT88/MT80i Update: 2011-08-01
Sub Project: Parameter Editor User Guide Page: 13 of 13
Revision: V1.06 Confidential: External Documentation

Tap 7: Photo Authorization (only for MVT600)

Select one or more events to enable the camera to take picture and store the image in memory
once the selected event is activated.
In default mode, once the SOS button is pressed (Input 1 is activated), the tracker will
automatically take picture and store it in memory.

Tool Bar

Item Description
Read Settings Read all preset values of the tracker.
Write Settings Write all settings (including all inputs in the 6 tabs below) to the
tracker.
Save Settings Save current settings for next or future configuration.
Load Settings Load the saved settings to implement them to a new tracker

After the tracker is configured, remove it from the USB data cable.

Copyright © 2010 Shenzhen Meiligao Electronics Co., Ltd. All rights reserved.