2PC WIRELESS SMD LED TRAILER LIGHT SET

MODEL NO: TB18LEDW

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Refer to
instructions
1. SAFETY
9 Check the battery status, ensure the lights are functioning correctly before using.
9 Please check that each light function works normally before using.
9 When the lights are in storage, check the batteries every 6 months.
9 You must complete the paring process when using replacement & additional lights.
9 Regularly check the lights after long periods of use.

2. INTRODUCTION
Magnetic wireless light clusters give essential light functions with no wiring required. Designed and manufactured for metal trailers, lorries,
agricultural machinery, tractors, and other vehicles up to 20m long. EU Plug wiring configurations and vehicles fitted with a 7-pin plug towing
trailers. Includes wireless transmitter that works with 7-pin plugs only. 5-Functions: brake lights, rear turn signal lights, rear position lights, license
plate lights, and return reflectors. Dual USB charging cable supplied allowing for both lights to be charged simultaneously. Supplied in storage
case.

3. SPECIFICATION
Model No:........................................................... TB18LEDW
Battery:...........................................................3.7V 2Ah Li-ion
Charging Time:...................................................................4hr
LED Type:...................................................... 24 x 0.2W SMD
Voltage:.............................................................................12V
Working Frequency:.....................................................2.4Ghz
IP Rating:.........................................................................IP65
Transmitter:.....................................2.6GHz (12V 7 pin outlet)
Fixing:.......................................................................Magnetic
Working Temperature Range:......................... -30°C to +50°C

MOUNTING POSITIONS FOR TRAILER REAR LAMPS AND

REFLECTORS
INDICATORS STOP/TAIL TRIANGULAR REFLECTORS
(must be above indicators)
between stop and tail light
100 Minimum separation
900 Maximum

1500 Maximum

350 Min

1000 max
250 min

FOG LAMP/S

Dimensions are in millimetres 400 Minimum

400 Max (also twin fog lamps if fitted) 400 Max All lamps must be ‘E’ marked

All lamps and reflectors should be mounted symmetrically. Trailers over 1.3M wide require at least one rear red fog lamp, and it must be
mounted on the centre line or to the offside of the trailer. If twin rear fog lamps are fitted they should be mounted symmetrically. Trailers over
1.6M wide require white front reflectors and white front markers/lamps. Trailers manufactured from October 2012 fitted with brakes re-
quire a reversing light. Trailers over 5M long may require side retro reflectors and side marker lamps. Trailers 6M long and over require red/
white side markers. The above information is given as a guide only; for full details consult 'The Road Vehicle Lighting Regulations'.

© Jack Sealey Limited Original Language Version TB18LEDW Issue 3 (ALL) 08/06/23
 4. INSTALLATION
4.1. TRAILER WIRING CODES (N-TYPE) Pin 1 Yellow Left hand direction indicator lamp
Pin 2 Blue Rear fog lamp/lamps
Pin 3 White Common return (earth)
Pin 4 Green Right hand direction indicator lamp
Pin 5 Brown Right hand tail lamp/ Rear registration lamp
Pin 6 Red Rear stop lamps
Pin 7 Black Left hand tail lamp/ Rear registration lamp
4.2. Plug the transmitter into the socket on the vehicle.
4.3. Turn on both the light units. The left hand green light bar (on the battery indicator) will flash when the unit has been switched on.
4.4. Start the vehicle and turn on the hazard lights.

5. OPERATION
‰ WARNING! When the red light on the low battery indicator is flashing charge the light.

fig.1 fig.2 fig.3

5.1. PAIRING THE DEVICE

5.1.1. Hold down the pairing button for 5 seconds. The right hand orange light (on the battery indicator) will illuminate when pairing is in
progress. The light will go out when pairing is complete.
NOTE: Always charge the lights to full before any long distance travel.
5.2. CHARGING THE LIGHTS
5.2.1. Make sure both units are charged and functioning correctly before use.
5.2.2. The red light will flash to indicate the battery level.
5.2.3. Use the USB cable provided to charge both units simultaneously.

6. MAINTENANCE
9 When the lights are in storage, check the batteries every 6 months.
9 Clean the lights with a damp cloth and make sure they are completely dry before storing.
NOTE: The battery fitted to this light is considered to be a consumable item and its ability to accept charge will reduce over time. We
will warranty it against mechanical and electrical defect for a period of one year, this does not cover fair wear and tear. If the battery is
not properly charged before first use, or regularly conditioned, its capacity will diminish. Under these circumstances we will not replace
the battery even if it is less than one year old.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations. REGISTER YOUR
PURCHASE HERE

WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.

BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack
Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 24 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 [email protected] www.sealey.co.uk
© Jack Sealey Limited Original Language Version TB18LEDW Issue 3 (ALL) 08/06/23