2130 Tractor
m
co
s.
l og
ta
ca
ep
John Deere Werke Mannheim
TM-4272
Printed in Germany (English)
ep
ca
ta
log
s.
co
m
/
2130 Tractor
Technical Manual
TM-4272 (Jan-79)
CONTENTS
SECTION 10 - GENERAL
Group 5 - Specifications
Group 10 · Pre-delivery, delivery and after-sales inspections
Group 15 - Lubrication and periodic service
Group 20 - Engine and tractor tune-up
Group 25 - Tractor separation
SECTION 20 - ENGINE
Group 5 · General information, diagnosing malfunctions
Group 10 · Cylinder head, camshaft and balancer shafts
Group 15 · Cylinder block, liners, pistons and connecting rods
Group 20 - Crankshaft, main bearings and flywheel
Group 25 - Timing gear train
Group 30 · Oil pump, oil pressure regulating valve,
oil cooler and oil filter
Group 35 - Engine cooling system
Group 40 - Speed control linkage
m
SECTION 30 - FUEL SYSTEM
Group 5 - Diagnosing malfunctions .
Group 10 • Fuel tank, water trap, transfer pump,
fuel filter and air cleaner
co
Group 15 - Roto-Diesel fuel injection pump
Group 20 - Fuel injection nozzles
Group 25 - Cold weather starting aids
s.
SECTION 40 - ELECTRICAL SYSTEM
Group 5 · Diagnosing malfunctions
Group 10 · "Bilux" lighting system (on earlier tractor models)
og
Group 11 - "Bilux" lighting system (on later tractor models)
Uroup U · "Bilux" lighting system (tractors with operator's cab)
Group 15 ·Sealed-beam lighting system (on earlier tractor models)
Group 16 - Sealed-beam lighting system (on later tractor models)
l
Group 20 - Starting motor
ta
Group 25 - Alternator and regulator
SECTION 50 - POWER TRAIN
Group 5 - Engine clutl!hes and clutch linkage
ca
Group 10 - High-Low shift unit
Group 11 · Creeper transmission
Group 15 - Collar-shift transmission
Group 20 - Differential
ep
Group 25 - Final drives
Group 30 - Independent PTO
SECTION 60 - FRONT AXLE, STEERING SYSTEM AND BRAKES
Group 5 - Front axle
Group 10 - Steering system
Group 15 - Hydraulic brakes
SECTION 70 - HYDRAULIC SYSTEM
Group 5 - General information, diagnosing malfunctions
and pressure tests
Group 10 - Oil reservoir, filter, valves and oil cooler
Group 15 - Hydraulic pump and transmission oil pump
Group 20 - Rockshaft
Group 25 · Selective control valves (spool type)
Group 30 - Selective control valves (poppet valve type)
and breakaway coupler
Group 35 - Remote cylinder
SECTION 80 - MISCELLANEOUS
Group 5 - Belt pulley
Group 10 - Seats
Copyright@ by
Group 15 - Front and rear wheels DEERE & COMPANY
Group 20 · Roll guard European Office
Group 25 - Operator's cab ventilation and heating D 68 Mannheim
Group 30 - Operator's cab All rights reserved
Printed in Germany (K 8)
2 2130 Tractor
TM-4272 (Jan-79)
Introduction
,,,, ....
''j
!.
m
co
s.
og
Use FOS Manuals for Reference Use Technical Manuals for Actual Service
When a technician should refe.r to a FOS
l
This technical manual is part of a twin concept of
ta
service: Manual for more information, a FOS
• FOS Manuals - for reference symbol like the one at the left is used in
the TM to identify the reference.
e Technical Manuals - for actual service
ca
The two kinds of manuals work as a team to give Some features of this technical manual:
you both the general background and technical
details of shop service.
e Table of contents on page 1
ep
Fundamentals of Service (FOS) Manuals cover e Contents at front of each Section
basic theory of operation, fundamentals of trouble
shooting, general maintenance, and basic types of
e Specifications at end of each Group
failures and their causes. FOS Manuals atre for e Torques for hardware at end of each Group
training new personnel and for reference ~y ex-
perienced technicians. 1
e Special tools at end of each Group
Technical Manuals are concise service guid~s for a This technical manual was planned and written for
specific machine. Technical Manuals are on-the-job you - an experienced technician. Keep it in a per-
guides containing only the vital inforination manent binder in the shop where it is handy. Re-
needed by an experienced technician. fer to it whenever in doubt about correct service
IMPORTANT: Your technical manual contains procedures or specifications.
the new SI metric measurements which have been
standardized internationally. Using the technical manual as a guide will reduce
error and costly delay. It will also assure you the
Example: best in finished service work.
New Old /). This safety alert symbol identifies impor-
10 N (Newton) ~ 1 kp . . tant safety messages in this manual. When
10 Nm (Newton-Meter) ~ lmkp you see this symbol, be alert to the possibility of
1 bar ~ 1 kp/cm2 personal injury and carefully read the message that
1 kW = 1.36 PS (1.34 HP) follow.
Exact conversion: 1 kp = 9.81N;1 mkp = 9.81Nm;1 kp/cm2 =
0.981 bar
Printed in Germany (K 8)
2130 Tractor General 10
TM-4272 (Jan-79) Specifications 5-1
Section 10
General
CONTENTS OF THIS SECTION
GROUP 5 -SPECIFICATIONS GROUP 15 -LUBRICATION AND PERIODIC
SERVICE
Page Page
Serial numbers . . 5-2 Lubrication and periodic service 15-1
Model numbers . 5-2
Engine . . . . . . 5-2
m
Engine clutch . . 5-2 GROUP 20 - ENGINE AND TRACTOR TUNE-UP
Electrical system . 5-2
Transmission . 5-2 General information . . . 20-1
High- Low shift unit
co . 5-3 Preliminary engine testing 20-1
Differential and final drives . 5-3 Engine tune-up . . . 20-2
Differential lock . . 5-3 Performance test 20-3
Power take-off ~ . . 5-3 Tractor adjustments 20-3
s.
Hydraulic system . 5-3 Standard torques 20-5
Power steering . . . 5-3 Special tools . . . . 20-5
og
Manual steering . . 5-3
Hydraulic brakes . 5-3
Handbrake . . . . . 5-3 GROUP 25 - TRACTOR SEPARATION
Capacities . . . . . 5-3
l
Travel speeds . . 5-3 Separating between engine and
ta
Front and rear wheels . 5-3 tractor front end . . . . . . . 25-1
Dimensions . . . . . . 5-3 Removing and installing engine 25-3
Removing and installing
ca
clutch housing . . . . . 25-5
GROUP 10 - PREDELIVERY, DELIVERY AND Removing and installing
AFTER-SALES INSPECTIONS final drives . . . . . . . 25-7
Removing and installing
ep
Predelivery inspection 10-1 rockshaft . . . . . . . 25-8
Delivery inspection 10-4 Tilting, removing and installing
After-sales inspection 10-4 operator's cab . . . . 25-10
Torques for hardware 25-14
: ,~
Special tools . . . . . 25-15
\
!
Printed in Germany (K 8)
Buy now
John Deere 2130 TM-4272 Technical Manual PDF
With Instant Download
