Scribd
Upload
30 views

#Include EEPROM.h

The document describes code for an Arduino project that controls relays and reads input from buttons, an IR receiver, and Bluetooth to control loads and power. It defines pins for buttons, relays, an IR receiver, and Bluetooth. It reads state from EEPROM and allows controlling loads through buttons, IR codes, and Bluetooth characters.

Uploaded by

Jaswanth Patnaik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
30 views

#Include EEPROM.h

The document describes code for an Arduino project that controls relays and reads input from buttons, an IR receiver, and Bluetooth to control loads and power. It defines pins for buttons, relays, an IR receiver, and Bluetooth. It reads state from EEPROM and allows controlling loads through buttons, IR codes, and Bluetooth characters.

Uploaded by

Jaswanth Patnaik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 4

#include <EEPROM.

h>
#include <IRremote.h>
#include <SoftwareSerial.h>
SoftwareSerial BT_Serial(2, 3); // RX, TX

const int RECV_PIN=A5;


IRrecv irrecv(RECV_PIN);
decode_results results;

#define Relay1 4 // Load1 Pin Out


#define Relay2 5 // Load2 Pin Out
#define Relay3 6 // Load3 Pin Out
#define Relay4 7 // Load4 Pin Out

#define touch1 A0 // Light Button Pin in


#define touch2 A1 // Lamp Button Pin in
#define touch3 A2 // Socket Button Pin in
#define touch4 A3 // Fan Button Pin in
#define touch5 A4 // Power Button Pin in

char bt_data; // variable to receive data from the serial port

int load1, load2, load3, load4, power;


int flag1, flag2, flag3, flag4, flag5;
int timer=0;

void setup(){
Serial.begin(9600);
BT_Serial.begin(9600);

irrecv.enableIRIn(); // Start the receiver


irrecv.blink13(true);

pinMode(touch1, INPUT);
pinMode(touch2, INPUT);
pinMode(touch3, INPUT);
pinMode(touch4, INPUT);
pinMode(touch5, INPUT);

pinMode(Relay1, OUTPUT); digitalWrite(Relay1, 1);


pinMode(Relay2, OUTPUT); digitalWrite(Relay2, 1);
pinMode(Relay3, OUTPUT); digitalWrite(Relay3, 1);
pinMode(Relay4, OUTPUT); digitalWrite(Relay4, 1);

load1 = EEPROM.read(1);
load2 = EEPROM.read(2);
load3 = EEPROM.read(3);
load4 = EEPROM.read(4);

power = EEPROM.read(5);
delay(500);
}

void loop() {

if(digitalRead(touch1)==1){
if(flag1==0){flag1=1;
load1 = !load1;
EEPROM.write(1, load1);
delay(100);
}
}else{flag1=0;}

if(digitalRead(touch2)==1){
if(flag2==0){flag2=1;
load2 = !load2;
EEPROM.write(2, load2);
delay(100);
}
}else{flag2=0;}

if(digitalRead(touch3)==1){
if(flag3==0){flag3=1;
load3 = !load3;
EEPROM.write(3, load3);
delay(100);
}
}else{flag3=0;}

if(digitalRead(touch4)==1){
if(flag4==0){flag4=1;
load4 = !load4;
EEPROM.write(4, load4);
delay(100);
}
}else{flag4=0;}

if(digitalRead(touch5)==1){
if(flag5==0){flag5=1;
power = !power;
EEPROM.write(5, power);
delay(100);
}
}else{flag5=0;}

if(irrecv.decode(&results)){
Serial.println(results.value,HEX);

if(results.value==0xFFB04F){ // For Load1 On


load1 = 0;
EEPROM.write(1, load1);
}
else if(results.value==0xFF6897){ // For Load1 Off
load1 = 1;
EEPROM.write(1, load1);
}

else if(results.value==0xFF7A85){ // For Load2 On


load2 = 0;
EEPROM.write(2, load2);
}
else if(results.value==0xFF30CF){ // For Load2 Off
load2 = 1;
EEPROM.write(2, load2);
}

else if(results.value==0xFF5AA5){ // For Load3 On


load3 = 0;
EEPROM.write(3, load3);
}
else if(results.value==0xFF10EF){ // For Load3 Off
load3 = 1;
EEPROM.write(3, load3);
}

else if(results.value==0xFF52AD){ // For Load4 On


load4 = 0;
EEPROM.write(4, load4);
}
else if(results.value==0xFF42BD){ // For Load4 Off
load4 = 1;
EEPROM.write(4, load4);
}

else if(results.value==0xFFE21D){ // For Power On


power = 0;
EEPROM.write(5, power);
}
else if(results.value==0xFFA25D){ // For Power Off
power = 1;
EEPROM.write(5, power);
}

irrecv.resume(); // Receive the next value


delay(100);
}

if(BT_Serial.available()>0){bt_data = BT_Serial.read();}

if(bt_data == 'A'){load1=0;EEPROM.write(1, load1);}


if(bt_data == 'a'){load1=1;EEPROM.write(1, load1);}

if(bt_data == 'B'){load2=0;EEPROM.write(2, load2);}


if(bt_data == 'b'){load2=1;EEPROM.write(2, load2);}

if(bt_data == 'C'){load3=0;EEPROM.write(3, load3);}


if(bt_data == 'c'){load3=1;EEPROM.write(3, load3);}

if(bt_data == 'D'){load4=0;EEPROM.write(4, load4);}


if(bt_data == 'd'){load4=1;EEPROM.write(4, load4);}

if(bt_data == 'E'){power=0;EEPROM.write(5, power);}


if(bt_data == 'e'){power=1;EEPROM.write(5, power);}

bt_data = '0';

if(power==1){
digitalWrite(Relay1, 1);
digitalWrite(Relay2, 1);
digitalWrite(Relay3, 1);
digitalWrite(Relay4, 1);
}else{
digitalWrite(Relay1, load1);
digitalWrite(Relay2, load2);
digitalWrite(Relay3, load3);
digitalWrite(Relay4, load4);
}

timer = timer+1;
if(timer>15){ timer=0;
BT_Serial.print(power); //send distance to MIT App
BT_Serial.print(";");
BT_Serial.print(load1); //send distance to MIT App
BT_Serial.print(";");
BT_Serial.print(load2); //send distance to MIT App
BT_Serial.print(";");
BT_Serial.print(load3); //send distance to MIT App
BT_Serial.print(";");
BT_Serial.print(load4); //send distance to MIT App
BT_Serial.println(";");
}

delay(50);
}

You might also like