Electr�cal W�r�ngs Easy Access D�agram For Program Parameters

The Dev�ce The Dev�ce

PID TEMPERATURE CONTROL UNIT
Ma�n Screen Password Screen
°C °C °C

w�th Two Relays w�th One Relay

°F °F °F

PO1 PO1 PO1

1 B-
NO
8 AL2 / PO2 8
AL1
AL2 / PO2
AL1
AL2 / PO2
AL1
AL2 / PO2

Ser�al Commun�cat�on (Alarm Output 2 or

Process Output 2)

5A@250V

5A@250V
(RS485, Modbus RTU) NO NO
2 A+ 9 9 AL1 / PO2

5A@250V
AL1 (Alarm Output 1 or Press Program button Enter Password w�th �ncrement Approve password
C (Alarm Output 1) C
3 SSR Output 10 10 Process Output 2)
PO1 12V to access password screen. or decrement buttons. w�th Enter button
(Process Output 1)
4 Max. 10mA 11 11

5 12 12 °C
°F
°C
°F
°C
°F *4 °C
°F
°C
°F *5 °C
°F *6 °C
°F *7
N 6 13
Process 13
Process
Supply Input Input

PT-100

PT-100
TC

TC
NOTE-1 PO1 PO1 PO1 PO1 PO1 PO1 PO1

Voltage L AL1 AL1 AL1 AL1 AL1 AL1 AL1

7 14 14
Eco PID
AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2

Supply 1A T
Sw�tch Fuse

°C °C °C °C °C °C °C

Note-1: External Fuse �s recommended. °F °F °F °F °F °F °F

Note-2: Stranded cable cross sect�on: 1,5mm², Sol�d cable cross-sect�on: 2,5mm² PO1 PO1 PO1 PO1 PO1 PO1 PO1

The str�pp�ng length �s 7mm to 9mm.

AL1 AL1 AL1 AL1 AL1 AL1 AL1
AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2

Note-3: Supply cables must comply w�th the requ�rements of IEC 60277 or IEC 60245.
°C °C °C °C °C °C °C

It �s adv�sed to use a two-pole supply sw�tch, des�gnated for th�s dev�ce, w�th open/ °F °F °F °F °F °F °F

Eco PID closed pos�t�ons marked, �n order to cut the power. It must be placed on the supply
�nput of the dev�ce at a place where the user can eas�ly reach.
PO1
AL1
AL2 / PO2
PO1
AL1
AL2 / PO2
PO1
AL1
AL2 / PO2
PO1
AL1
AL2 / PO2
PO1
AL1
AL2 / PO2
PO1
AL1
AL2 / PO2
PO1
AL1
AL2 / PO2

Eco PID, PID Temperature Control Un�t V External fuse must be on phase connect�on of the supply �nput.
- 3 d�g�t process (PV) and 4 d�g�t set (SV) d�splay Z External fuse must be on (+) l�ne connect�on of the supply �nput.
°C
°F
°C
°F
°C
°F
°C
°F
°C
°F
°C
°F
°C
°F

- Temperature sensor �nput (TC,RTD) Make sure that the power supply voltage range �s su�table for the dev�ce. PO1 PO1 PO1 PO1 PO1 PO1 PO1

- Programmable ON/OFF, P, PI, PD and PID control forms Sw�tch on the power supply only after all the electr�cal connect�ons are �n place.
AL1 AL1 AL1 AL1 AL1 AL1 AL1
AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2

- Adaptat�on of PID Coeff�c�ents to the system w�th Self-Tune and Auto-Tune

c
To reduce the effect of electr�cal no�se on dev�ce, low voltage l�ne (espec�ally sensor
- Programmable Heat�ng or Cool�ng Funct�ons for Control Output °C °C
*1 °C °C °C °C

�nput cable) w�r�ng must be separetely from h�gh current and voltage l�ne. If poss�ble, °F °F °F °F °F °F

- Selectable Alarm Funct�ons for Alarm Output use sh�elded cable and sh�eld must be connected to ground only one s�de.
- Ser�al RS485 Commun�cat�on (opt�onal)
PO1 PO1 PO1 PO1 PO1 PO1
AL1 AL1 AL1 AL1 AL1 AL1
AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2

Eco ser�es temperature controllers are des�gned for measur�ng and controll�ng a D�mens�ons
temperature value. They can be used �n many appl�cat�ons w�th the�r TC and RTD Max�mum 9 mm / 0.35 �nch
°C
°F
°C
°F
°C
°F
°C
°F
°C
°F

temperature measurement �nput, mult�-funct�on control outputs, selectable alarm

funct�ons.
PO1 PO1 PO1 PO1 PO1
AL1 AL1 AL1 AL1 AL1
AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2

They are ma�nly used �n glass, plast�c, petro-chem�stry, text�le, automot�ve and mach�ne Eco PID

48 mm / 1.89 �nch
product�on �ndustr�es. Accurate and advanced controll�ng �s performed w�th selectable °C
°F °C °C °C °C °C

ON-OFF, P, PI, PD, PID and Self Tune/Auto Tune PID funct�ons.
°F °F °F °F °F

SPECIFICATIONS PO1 AL1

PO1
AL1
AL2 / PO2
PO1
AL1
AL2 / PO2
PO1
AL1
AL2 / PO2
PO1
AL1
AL2 / PO2
PO1
AL1
AL2 / PO2

Process Input: Thermocouple (TC): J, K, R, S, T and L (IEC584.1)(ITS90) PO2

/
AL2

Thermores�stance (RTD): Cu-50 and PT-100 (IEC751)(ITS90) °C °C

*2 °C °C

Measurement Range: Please refer to process �nput type select�on �n process menu °F °F °F °F

parameters sect�on. PO1

AL1
PO1
AL1
PO1
AL1
PO1
AL1

Accuracy: AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2

Thermocouple (TC):( ± 0.25% of full scale or ± 3ºC, wh�ch one �s greater) ±1 d�g�t max. 48 mm / 1.89 �nch 80,52 mm / 3.17 �nch
6 mm / 0.24 �nch
Thermores�stance (RTD):( ± 0.25% of full scale or ± 2ºC, wh�ch one �s greater) ±1 d�g�t Panel Mount�ng
°C
°F
°C
°F *2,3
*1 - ON/OFF Hysteres�s parameter �s not act�ve unless parameter �s set as .
max. PO1 PO1
*2 - Soft Start parameters( , , ) �s not act�ve unless parameter �s set as .
Cold Junct�on Compensat�on: Automat�cally ±0.1°C/1°C AL1 AL1

*3 - Soft Start Control Output and Soft Start Control T�me parameters �s not act�ve �f parameter
1- Before mount�ng the dev�ce �n your panel,
AL2 / PO2 AL2 / PO2

1
L�ne Compensat�on: Max�mum 10 Ohm �s set as .
Sensor Break Protect�on: Upscale make sure that the cutout �s of the r�ght s�ze. *4 - PID control parameters are not act�ve unless parameter �s set as .
°C
*2,3
Sampl�ng Cycle: 0.1 second 2- Check front panel gasket pos�t�on. °F
*5 - Alarm-2 parameters are not act�ve �f parameter �s set as .
*6 - Commun�cat�on parameters are not act�ve on dev�ces have no commun�cat�on module.
Input F�lter: Programmable °C
°F
3- Insert the dev�ce through the cutout. If the PO1
AL1
AL2 / PO2 *7 - If �s d�fferent from 0 and user enters to program menu w�thout enter�ng the password
Control Form: ON/OFF, P, PI, PD or PID (Control form can be programmed by the user) Ec
o mount�ng clamps are on the un�t, put out them Prot menu �s not shown.
Note: User can ex�t from any parameter screen w�thout sav�ng the values by press�ng button. If
PO

before �nsert�ng the un�t to the panel.

1

OUTPUT
PO AL
2 1
AL
2
/

no operat�on for 120 seconds, dev�ce automat�cally return to ma�n screen.

Process Output: Relay (5A@250VV at res�st�ve load) or SSR Dr�ver Output 3
(Max�mum 10mA, Max. 12VZ ) Tune Operat�on
2 4- Insert the mount�ng clamps to the two of Easy Access D�agram For Sensor Break Output
Alarm Output: Relay (5A@250VV at res�st�ve load)
des�gnated holes that located four s�des of Value From Ma�n Screen Start�ng the Tune operat�on
SUPPLY VOLTAGE (It must be determ�ned �n order) 6
4
5
1- Enter to the parameter �n menu and select
230VV (±15%) 50/60Hz - 4VA dev�ce. °C
Ma�n Screen
°C °C °C
Ma�n Screen
or ,then press button for sav�ng parameter and turn to ma�n
5- Drag the mount�ng clamps �n d�rect�on 5
°F °F °F °F

115VV (±15%) 50/60Hz - 4VA screen. Or eas�ly press button for 3 seconds* �n ma�n screen.
unt�l the dev�ce completely �mmob�le w�th�n the 2- Observe that bl�nks �n set d�splay.
100-240VV 50/60Hz - 4VA
PO1 PO1 PO1 PO1
°C AL1 AL1 AL1 AL1
°F
AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2
*Only Self Tune can be started by th�s way.
24VV(±%15) 50/60Hz - 4VA
Ec
o
panel.
Cancel�ng Tune operat�on:
PO
1

6- In order to remove dev�ce push on the

AL

Press Enter button to save

PO 1
2
AL

24VW (±%15) 50/60Hz - 4VA Change the sensor break

2
/

new sensor break output value 1- If sensor breaks;

10...30VZ - 4W mount�ng clamp as shown w�th arrow 6 and output value w�th �ncrement 2- If tune operat�on can not be completed �n 8 hours;
or decrement buttons. and ex�t.
DISPLAY pull back. 3- Wh�le heat�ng self tune �s runn�ng, �f process value becomes
greater than process set value;
Process D�splay: 16 mm Red 3 d�g�t LED D�splay Note1: User can ex�t from parameter screen w�thout sav�ng the 4- Wh�le cool�ng self tune �s runn�ng, �f process value becomes less
Set Value D�splay: 9 mm Orange 4 d�g�t LED D�splay values by press�ng button. If no operat�on for 120 seconds, dev�ce than process set value;
Led Ind�cators: PO1 (SSR Process Output Status Led), PO2 (Relay Access and Change Set Values automat�cally ex�ts from parameter screen. 5- Wh�le tune operat�on �s runn�ng, �f user changes the process set
Note2: Sensor break output value can be adjusted on programm�ng value;
Process Output Status Led), AL1, AL2 (Alarm Output Status Leds), °C
Ma�n Screen
°C °C °C
Ma�n Screen
sect�on too. 6- Wh�le tune operat�on �s runn�ng, �f user changes the
ºC, ºF LEDs
°F °F °F °F

parameter �n menu;
ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS PO1
AL1
PO1
AL1
PO1
AL1
PO1
AL1
Then tune operat�on �s canceled, dev�ce cont�nues to run w�th former
AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2
PID parameters w�thout chang�ng PID parameters.
Operat�ng Temperature: 0...50ºC
Hum�d�ty : 0-90%RH (none condens�ng) Press �ncrement or decrement Press Enter button to save new
Mechan�cal Impacts: 1Joule (IK06) button to change process set value. set value and return the ma�n screen.
Protect�on Class: NEMA 4X (IP65 at front, IP20 at rear) Temperature Set Value Parameter (Default: 200) MODBUS ADDRESS: 40000
We�ght: 150 gr. a

Note-1: User can ex�t from set value sect�on w�thout sav�ng the values by press�ng button. If no
D�mens�on: 48 x 48 mm, Depth: 86,5 mm operat�on for 120 seconds, dev�ce automat�cally ex�ts from Set Value sect�on.
Panel CutOut: 46 x 46 mm Note-2: Set value can be adjusted between Set Value Low and H�gh L�m�t ( - ). Introduct�on Brochure. ENG EcoPID 01 V08 02/22
 Alarm
: Process Menu Parameters : Alarm-2 Menu Parameters (Only for dev�ces w�th two relays) Output Process Alarm Process Process Alarm
Warranty
Set Set Set Set Set
: Process �nput type select�on; (Default: ) Modbus Address: 40004 Alarm-2 menu parameters can be seen only �f parameter �s . EMKO Elektron�k warrants that the equ�pment del�vered �s free from
: J type (Fe,Cu,N�) Thermocouple , -199ºC,900ºC ; -199ºF,999ºF : Alarm-2 set value. (Default: 400) Modbus Address: 40046
Dev�at�on Band defects �n mater�al and workmansh�p. Th�s warranty �s prov�ded for a
: J type (Fe,Cu,N�) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF : Alarm-2 hysteres�s value. It can be adjusted from %0 to %50 of the Scale
: K type (N�,Cr,N�) Thermocouple , -199ºC,999ºC ; -199ºF,999ºF ( - ). (Default: 0) Modbus Address: 40047 Alarm Alarm Alarm
per�od of two years. The warranty per�od starts from the del�very
: K type (N�,Cr,N�) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF : Alarm-2 type select�on. (Default: ) Modbus Address: 40048 Hysteres�s Hysteres�s
date.
Process Value
: R type (Pt13%RhPt) Thermocouple , 0ºC,999ºC ; 32ºF,999ºF : Alarm-2 set low l�m�t parameter. It can be adjusted from operat�on scale m�n�mum Alarm Th�s warranty �s �n force �f duty and respons�b�l�t�es wh�ch are
: R type (Pt13%RhPt) Thermocouple , 0.0ºC,99.9ºC ; 32.0ºF,99.9ºF to alarm-2 set h�gh l�m�t. (Default: 0) Modbus Address: 40049 Output Process
Set
Alarm
Set
Process
Set
Process
Set
Alarm
Set determ�ned �n warranty document and �nstruct�on manual performs
: S type (Pt10%RhPt) Thermocouple , 0ºC,999ºC ; 32ºF,999ºF : Alarm-2 set h�gh l�m�t parameter. It can be adjusted from alarm-2 set low l�m�t to
: S type (Pt10%RhPt) Thermocouple , 0.0ºC,99.9ºC ; 32.0ºF,99.9ºF operat�on scale max�mum. (Default: 500) Modbus Address: 40050 by the customer completely.
: T type (Cu,Cu,N�) Thermocouple , -199ºC,400ºC ; -199ºF,752ºF : Alarm-2 on delay t�me. It can be adjusted from 0 to 9999 seconds. (Default: 0) Dev�at�on Range
Alarm
Ma�ntenance
: T type (Cu,Cu,N�) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF Modbus Address: 40051 Alarm Alarm
: L type (N�,Cr,Co / N�,Fe,Mn,Cu) Thermocouple , -150ºC,800ºC ; -199ºF,999ºF : Alarm-2 off delay t�me. It can be adjusted from 0 to 9998 seconds. If �t �s h�gher Hysteres�s Hysteres�s Repa�rs should only be performed by tra�ned and spec�al�zed
Process Value
: L type (N�,Cr,Co / N�,Fe,Mn,Cu) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF than 9998, �s seen on the screen and Alarm Latch�ng Output �s selected. In
Alarm
personnel. Cut power to the dev�ce before access�ng �nternal parts.
: Cu-50 , -199ºC,200ºC ; -199ºF,392ºF alarm latch�ng output mode �n order to make pass�ve alarm outputs, press enter Output Process Alarm Process Do not clean the case w�th hydrocarbon-based solvents (Petrol,
: Cu-50 , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF button at ma�n screen. (Default: 0) Modbus Address: 40052 Set Set Set

: Pt-100 , -199ºC,650ºC ; -199ºF,999ºF

Tr�chlorethylene etc.). Use of these solvents can reduce the
: Pt-100 , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF : Commun�cat�on Parameters (Only for dev�ces w�th RS-485 com.) Dev�at�on Range mechan�cal rel�ab�l�ty of the dev�ce. Use a cloth dampened �n ethyl
: Un�t Select�on. or can be chosen. (Default: ) Modbus Address: 40005 : Commun�cat�on access�ng address of dev�ce. (Default: 1) Modbus H�gh Alarm
Alarm
alcohol or water to clean the external plast�c case.
: Operat�on Scale m�n�mum (Low L�m�t) value. It changes accord�ng to the process Address: 40056 Hysteres�s

�nput type and scale. (Default: -199) Modbus Address: 40006 : Commun�cat�on Baud Rate. (Default: 3) Modbus Address: 40057 Process Value Other Informat�ons
: Operat�on Scale max�mum (H�gh L�m�t) value. It changes accord�ng to the : 1200 Baud Rate. Manufacturer Informat�on:
process �nput type and scale. (Default: 900) Modbus Address: 40007 : 2400 Baud Rate.
Error Messages
1-Sensor fa�lure �n analog �nputs. Sensor connect�on �s wrong or there
Emko Elektron�k Sanay� ve T�caret A.Ş.
: Process Set value Low L�m�t. M�n�mum set value �s def�ned w�th th�s parameter. : 4800 Baud Rate. °C

Bursa Organ�ze Sanay� Bölges�, (Feth�ye OSB Mah.)

°F

It can be adjusted between Operat�on Scale m�n�mum and max�mum ( - ) : 9600 Baud Rate. �s no sensor connect�on.
values. (Default: -199) Modbus Address: 40008 : 19200 Baud Rate.
PO1
AL1
AL2 / PO2
a

2-If programm�ng sect�on enter�ng password �s d�fferent from “0” and

Al� Osman Sönmez Bulvarı, 2.Sokak, No: 3 16215
: Process Set value H�gh L�m�t. Max�mum set value �s def�ned w�th th�s parameter. : 38400 Baud Rate. BURSA/TÜRKİYE
°C
user accesses to the parameter by enter button w�thout enter�ng the
It can be adjusted between Operat�on Scale m�n�mum and max�mum ( - ) : Par�ty Select�on for Commun�cat�on. (Default: 0) Modbus Address: 40058
°F

password and wants to change a parameter, the warn�ng message �s Phone : +90 224 261 1900
values. (Default: 900) Modbus Address: 40009 : No Par�ty. PO1
shown on the bottom d�splay as shown on the left. Dev�ce does not Fax : +90 224 261 1912
: D�splay offset for process value. It can be adjusted from -10% of scale to 10% of
AL1

: Odd Par�ty. AL2 / PO2

allow to do any changes w�thout enter�ng the password correctly.

scale. It �s added to the process d�splay value. (Default: 0) Modbus Address: 40010 a
: Even Par�ty. °C
a
Repa�r and Ma�ntenance Serv�ce Informat�on:
°F

: Def�ne f�lter t�me(sec) for d�splayed value. (Default: 1.0) Modbus Address: 40011 : Stop B�t Select�on for Commun�cat�on. (Default: 0) Modbus Address: 40059 3-If value that �s read from the analog �nput �s lower than process set
: 1 Stop B�t.
PO1
AL1 low l�m�t parameter value ( ), value on the top d�splay starts to bl�nk Emko Elektron�k Sanay� ve T�caret A.Ş.
: Control Menu Parameters
AL2 / PO2

: 2 Stop B�t. as shown on the p�cture. Bursa Organ�ze Sanay� Bölges�, (Feth�ye OSB Mah.)
°C
a
: Th�s parameter determ�nes, wh�ch output w�ll be Process control output. If �s °F

4-If value that �s read from the analog �nput �s h�gher than process set Al� Osman Sönmez Bulvarı, 2.Sokak, No: 3 16215
chosen, process output �s relay output, �f �s chosen, process output �s SSR output. : Protec�on Menu Parameters PO1
h�gh l�m�t parameter value ( ), value on the top d�splay starts to bl�nk BURSA/TÜRKİYE
(Default: ) Modbus Address: 40015
AL1

: Password for access�ng to the programm�ng sect�on. It can be adjusted from 0 to AL2 / PO2

as shown on the p�cture.

: Process Type Select�on. It can be (Heat�ng) or (Cool�ng).(Default: ) 9999. If �s 0, password screen �s not seen. If �s d�fferent from 0 and user °C
°F
a
Phone: +90 224 261 1900
Modbus Address: 40016 enters to the menu pages w�thout enter�ng the password, all the menus can be 5-If value that �s read from the analog �nput �s lower than sensor scale Fax : +90 224 261 1912
: Process Control Type Select�on. It can be or . (Default: ) Modbus observed except protect�on menu . But dev�ce does not allow to do any changes PO1
AL1
low l�m�t, value on the top d�splay starts to bl�nk as shown on the
Address: 40017 �n parameters. (Default: 0) Modbus Address: 40063
AL2 / PO2

p�cture. Order�ng Informat�on

°C

: Hysteres�s value. It can be adjusted from %0 to %50 of the Scale ( - ). : User default parameters. Th�s parameter �s used for sav�ng all parameters to °F
a

6-If value that �s read from the analog �nput �s h�gher than sensor scale
If = , then th�s parameter can be seen. (Default: 3) Modbus Address: 40018 restore later or restore all parameters saved before. If �s chosen, all parameters A B C D E
h�gh l�m�t, value on the top d�splay starts to bl�nk as shown on the
Eco PID ( 48x48 DIN 1/16 )
PO1

: Sensor Break Output Value. It can be adjusted from %0 to %100. (Default: 0.0) saved before are restored. If �s chosen, all parameters saved to restore later. If
AL1

p�cture.
AL2 / PO2

Modbus Address: 40019 �s chosen, noth�ng �s changed. (Default: ) Modbus Address: 40064 4 . . . S .
: The cho�ce of d�splayed text on process value d�splay when sensor �s broken. : Th�s parameter �s used for restore factory defaults. If �s chosen, factory Installat�on
It can be or . (Default: ) Modbus Address: 40020 defaults parameters restored. If �s chosen, noth�ng �s changed. (Default: ) A D�mens�on
Before beg�nn�ng �nstallat�on of th�s product, please
: Soft Start Set value. Dev�ce operates �n Soft Start mode, unt�l the temperature Modbus Address: 40065
read the �nstruct�on manual and warn�ngs below 4 48x48 DIN 1/16

c
reaches Soft Start set value. If �s selected, Soft Start mode �s d�sabled. (Default: ) Remove all �nput/output connect�ons on term�nals before restor�ng
Modbus Address: 40021 parameters to user/factory defaults.
carefully.
B Supply Voltage
: Soft Start Control Output. Th�s parameter determ�nes soft start mode control In package, 1 100-240VV 50/60Hz - 4VA
output percentage. It can be adjusted from %10 to %90. (Default: 10.0) Modbus Modbus Addresses of Dev�ce Operat�on Info. (Read Input Reg�ster) -One p�ece un�t
Address: 40022 2 24VW (±%15) 50/60Hz - 4VA
Modbus Address: 30000 D�splayed Temperature Value -Two p�eces mount�ng clamp
: Soft Start Control T�me. Th�s parameter determ�nes soft start mode control t�me. 3 115VV (±%15) 50/60Hz - 4VA
Modbus Address: 30001 Status of LEDs: b�t.1 ALR1, b�t.2 ALR2, b�t.9 °C
(Default: 1.0) Modbus Address: 40023 b�t.10 °F, b�t.11 PO2, b�t.12 PO1 -One p�ece �nstruct�on manual 5 230VV (±%15) 50/60Hz - 4VA
Modbus Address: 30002 Status of Dev�ce: b�t.0 Sensor Break Status 6 10...30VZ - 4W
: PID Menu Parameters A v�sual �nspect�on of th�s product for poss�ble damage occured 7 24VV (±%15) 50/60Hz - 4VA
PID menu parameters can be seen only �f parameter �s . Alarm Types 9 Customer Spec�f�ed
dur�ng sh�pment �s recommended before �nstallat�on. It �s your
: If tune parameter �s set to or , dev�ce start to calculate PID Alarm
parameters automat�cally. (Default: ) Modbus Address: 40027 Output Alarm respons�b�l�ty to ensure that qual�f�ed mechan�cal and electr�cal C Outputs-1
Set
: Proport�onal band. It can be adjusted from %1.0 to %100.0. (Default: 10.0) techn�c�ans �nstall th�s product. 1R 1 x Relay Output (5A@250VV at Res�st�ve Load) (NO,C)
Modbus Address: 40028 Process H�gh If there �s danger of ser�ous acc�dent result�ng from a fa�lure or defect 2R 2 x Relay Output (5A@250VV at Res�st�ve Load) (NO,NO,C)
: Integral T�me. It can be adjusted from 0 to 3600 second. (Default: 100) Modbus Alarm �n th�s un�t, power off the system and the electr�cal connect�on of the
Address: 40029 Alarm D Outputs-2
: Der�vat�ve T�me. It can be adjusted from 0.0 to 999.9 second. (Default: 25.0) Hysteres�s dev�ce from the system.
Process Value S SSR Dr�ver Output (Max. 10mA, Max. 12VZ)
Modbus Address: 40030 Alarm The un�t �s normally suppl�ed w�thout a power sw�tch or a fuse. Use
: Output Control Per�od. It can be adjusted from 0.5 to 150 second. (Default: 1.0) Output Alarm power sw�tch and fuse as requ�red. E Commun�cat�on
Modbus Address: 40031 Set
Be sure to use the rated power supply voltage to protect the un�t 0 None
: Set value offset. (Set + ) �s used as set value �n PID calculat�ons. Th�s
aga�nst damage and to prevent fa�lure. 485 RS-485 Commun�cat�on
parameter �s used for sh�ft�ng the proport�onal band. It can be adjusted from (- /2) to
Process Low
( /2). (Default: 0) Modbus Address: 40032 Keep the power off unt�l all of the w�r�ng �s completed so that electr�c Before comm�ss�on�ng the dev�ce, parameters must be set �n
Alarm Alarm
Hysteres�s
shock and trouble w�th the un�t can be prevented. accordance w�th des�red use. Incomplete or �ncorrect conf�gurat�on
: Alarm-1 Menu Parameters Process Value
can cause dangerous st�uat�ons.
Alarm Never attempt to d�sassemble, mod�fy or repa�r th�s un�t. Tamper�ng
: Alarm-1 set value. (Default: 300) Modbus Address: 40036 Output Because of l�m�ted mechan�cal l�fe of relay output contact, SSR
Process Process Alarm w�th the un�t may results �n malfunct�on, electr�c shock or f�re.
: Alarm-1 hysteres�s value. It can be adjusted from %0 to %50 of the scale Set Set Set
output �s recommended wh�ch the dev�ce use PID control algor�tm.
( - ). (Default: 0) Modbus Address: 40037 Do not use the un�t �n combust�ble or explos�ve gaseous
Dev�at�on H�gh The dev�ce w�th ON/OFF control algor�tm, hysteres�s parameter must
: Alarm-1 type select�on. (Default: ) Modbus Address: 40038 atmospheres. Dur�ng the equ�pment �s putted �n hole on the metal be set a su�table value for your system, to avo�d too much relay
: Alarm-1 set low l�m�t parameter. It can be adjusted from operat�on scale m�n�mum Alarm
Alarm
panel wh�le mechan�cal �nstallat�on some metal burrs can cause sw�tch�ng.
to alarm-1 set h�gh l�m�t. (Default: 0) Modbus Address: 40039 Hysteres�s
Process Value �njury on hands, you must be careful. Vac,
: Alarm-1 set h�gh l�m�t parameter. It can be adjusted from alarm-1 set low l�m�t to
operat�on scale m�n�mum. (Default: 500) Modbus Address: 40040 Alarm Montage of the product on a system must be done w�th �t’s mount�ng Vdc,
Output
: Alarm-1 on Delay T�me. It can be adjusted from 0 to 9999 seconds. (Default: 0)
Process
Set
Alarm
Set
Process
Set clamp. Do not do the montage of the dev�ce w�th �nappropr�ate Vdc or Vac can be appl�ed
Modbus Address: 40041 mount�ng clamp. Be sure that dev�ce w�ll not fall wh�le do�ng the
: Alarm-1 off Delay T�me. It can be adjusted from 0 to 9998 seconds. If �t �s h�gher Dev�at�on Low
montage.
than 9998, �s seen on the screen and alarm latch�ng output �s selected. In alarm Alarm
latch�ng output mode �n order to make pass�ve alarm outputs, press enter button at Alarm It �s your respons�b�l�ty �f th�s equ�pment �s used �n a manner not
Hysteres�s
ma�n screen. (Default: 0) Modbus Address: 40042 Process Value spec�f�ed �n th�s �nstruct�on manual.