Fast Ethernet Converter

Fast Ethernet Converter Board Diagram

Leftside Rightside

It is fast Ethernet fiber optic transmission equipment which can converter between two different network
POWER
cables and optical fiber transmission medium. Supporting 10/100 Mbps network bandwidth, this product Power

can be used in pairs and also can be used with other equipments. It is widely used in surveillance, home FED
SD
network fiber, etc. Link

Application Fiber

Ne
tw Power Green
ork
Sw Ethernet Port SFP Port Grounding Power Input
itc LED Indicator
h
Instruction：
1) Power refers to Power LED indicator; Optical fiber interface LED indicator of FED, SD, the LINK is
refer to:
F Link--indicating fiber port connection status. Bright: connection OK; Off: connection fail; Flicker:
Co ast
nv Eth connection OK and have the data.
er er
te ne
r t SD--Fiber port signal detection. Bright: optical fiber connection correct; Off: optical fiber
connection fail.
O
p FED--Remote fault mode receiving. Bright: 80 ms; Off: 20 ms; Often Off: Not receive.
2) Diagnosis of LED indicator fault as follow:
ti
ca
lF
ib
e LED Indicators of
r Fiber Link Fiber SD Fiber FED Status
Power & Ethernet
IP

Bright Bright Bright Off Connect well

Ca
m
er
a

Flicker Flicker Bright Off Connect well, with data transmission

Fa nv
st ert
Co

Et er

Off Off Bright Off Remote power port unable to connect

he
rn
et

Off Off Off Off Fiber optical RX drops, TX/RX drops

Off Off Bright Flicker Fiber optical TX/RX drops
Feature
Provide 1 100 Mbps fiber optic and 1 network port which can converter between network data, fiber Installation
optic and power;
Please check the following items before installation. If any missing, please contact the dealer.
Using X9 fiber modules and SC interface, with the single mode double optical fiber, up to 20 km
Fast Ethernet Converter 1pc
transmission distance;
Power Adapter 1pc
Compatible with IEEE 802.3 10 BASE-T, IEEE 802.3 u 100 BASE-TX/FX Ethernet standards; MIT Hanger 2pcs
Support 10/100 Mbps full/half duplex automatic adaptation and automatic MDI/MDIX; User Manual 1pc
Excellent circuit protection, effectively improved lightning protection, anti-static products and anti-
interference ability; Installation Steps

Dynamic LED status indicator, real-time display of current working status, simple working status and 1) Please turn off the signal source and device power before installation; Installation with power on may
damage the device;
troubleshooting;
2) Please check if the network cables being taken up by other devices;
Support wide voltage DC12V~24V input;
3) Use network cable to connect RJ45 Port of Fast Ethernet Converter with NVR or network devices like
MIT compact aluminum shell structure design, convenient racks, desktop, wall-hung style installation.
computer;
4) Use two single mode optical fibers tor connect two fiber ports of two Fast Ethernet Converters.
Caution Pay attention to that the optical fibers connecting RX and TX line should be CROSS connected. That is:
1) Make sure two 2 optical fibers should be connected with the fiber ports of the device crosswise ; if one end of optical fiber line connected to the module TX interface, the other end should be connected
2) If using optical port, customer need to purchase SFP module additional. to the RX interface;
3) The equipment must connect anti-thunder ground, otherwise the protection level of the equipment will 5) Please check if the installation is correct and power the system;

be greatly reduced please use 20th or over wire connect ground port to the ground , 6) Please check if the network is working.

1 2
 Fast Ethernet Converter Fast Ethernet Converter
Specification
连接接口 RJ 45 Making Method
Instruments to be used: wire crimper, network tester.
Item Description
Wire sequence of RJ45 plug should conforms with EIA/TIA568A or 568B standards.
Power Supply Power Adapter
Power Voltage range DC12V~24V 1) Shuck off about 2cm long of the insulating layer to expose the 4 pairs UTP cables;

Consumption ＜2W 2) Seperate the 4 pairs UTP cables and straighten them up;

Ethernet Port Ethernet port：10/100Mbps 3) Line up the 8 pieces of cables per EIA/TIA 568A or 568B standards;
Ethernet Port
parameter Transmission Distance Ethernet port ：0～100m 4) Brunt cut the cables to leave 1.5cm wire exposed and make sure the wire ends are leveled off;
Fiber Port SFP: Single Fiber & Double Fiber Optional 5) Plug 8 cables into RJ45 plug, make sure each cable is in each pin;
Fiber Port Bandwidth 155Mbps 6) Then use wire crimper to crimp it;
parameter
Transmission Distance Depend on SFP module performance 7) Repeat above 5 steps to make the another end;
Network 8) Using network tester to test the cable .
exchange Network Standard IEEE802.3 10BASE-T,IEEE802.3u 100BASE-TX/FX
specification
pin color pin color
Power indicator light Green white/green white/orange
1 1
Status
Network indicator Green on RJ45
Indicator 2 green 2 orange
Fiber indicator FED, SD, LINK 3 Green LEDs white/green
3 white/orange 3
ESD 3 level，Standard ：IEC61000-4-2 blue
Protection 4 blue 4
level Lightning protection 3 level，Standard ：IEC61000-4-5
5 white/blue 5 white/blue
Working Temperature 0℃~55℃ orange
6 6 green
Operation
Storage Temperature -40℃~85℃ white/brown
environment 7 7 white/brown
Humidity (Non-Condensing) 0~95% brown
8 brown 8
Dimension (L*W*H) 103mm×82mm×25mm
Material Aluminum Alloy
Mechanical EIA/TIA 568A EIA/TIA 568B
Color Black
Weight 172g

Product are subject to change without prior notice Make sure if one end is EIA/TIA568A,the other end should also be EIA/TIA568A.
Make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
Trouble Shooting
连接接口
Please find the following solution when the device doesn't work
Please confirm if the installation is correct;
Please confirm if the RJ45 cable order is in accordance with the EIA/TIA568A or 568B industry
连接接口
standards;
The maximum transmission distance depends on the signal source and cable quality, please do not
exceed the maximum transmission distance;
Please replace a failure device with a normally working device to check if the device is broken;
If the problem still exists, please contact the factory.

3 4