KEIHIN SH7058 37805 Rxx HONDA
plugin 492
Ecu TYPE 01 for vehicle equipped with AUTOMATIC transmission, ECU connector side.
https://ecu.design
KEIHIN SH7058 37805 Rxx HONDA
Ecu TYPE 01 for vehicle equipped with MANUAL transmission, ECU connector side
https://ecu.design
KEIHIN SH7058 37805 Rxx HONDA
DIRECT CONNECTION ECU TYPE 01
In order to connect to the ECU use the CABLE F32GN037C.
Make sure that the POWER led (red) on Trasdata is ON.
CONNECTOR ECU TYPE 01
WARNING :
on this ECU you must use two different flat cables: one is for the READING procedure and one is
for the WRITING procedure.
https://ecu.design
KEIHIN SH7058 37805 Rxx HONDA
DIRECT CONNECTION – ECU TYPE 01 READING:
For the READING procedure use the FLAT cable F34NTF53
https://ecu.design
KEIHIN SH7058 37805 Rxx HONDA
For a correct soldering procedure clean very well the soldering lay-by pins from the plastic film.
We suggest you to use a fine grit glass-paper smoothing by gentle pressure
the connection of the lay by pins.
https://ecu.design
KEIHIN SH7058 37805 Rxx HONDA
DIRECT CONNECTION – ECU TYPE 01 WRITING:
For the WRITING procedure use the FLAT cable F34NTF51
https://ecu.design
KEIHIN SH7058 37805 Rxx HONDA
For a correct soldering procedure clean very well the soldering lay-by pins from the plastic film.
We suggest you to use a fine grit glass-paper smoothing by gentle pressure
the connection of the lay by pins. On the Micro side connect the BLUE wire to the pin as shown in
the picture here below.
On the other side connect all the wires to the pins and make the LINK connection too as shown in
the picture here below. Remove the LINK after the writing procedure.
https://ecu.design
KEIHIN SH7058 37805 Rxx HONDA
Ecu TYPE 02 for vehicle equipped with AUTOMATIC transmission, ECU connector side
Ecu TYPE 02 for vehicle equipped with MANUAL transmission, ECU connector side
https://ecu.design
KEIHIN SH7058 37805 Rxx HONDA
https://ecu.design
KEIHIN SH7058 37805 Rxx HONDA
DIRECT CONNECTION ECUTYPE 02
In order to connect to the ECU use the CABLE F32GN037C.
Make sure that the POWER led (red) on Trasdata is ON.
CONNECTOR ECU TYPE 02
WARNING :
on this ECU you must use two different flat cables: one is for the READING procedure and one is
for the WRITING procedure
https://ecu.design
KEIHIN SH7058 37805 Rxx HONDA
DIRECT CONNECTION – ECU TYPE 02 READING:
For the READING procedure use the FLAT cable F34NTF53
https://ecu.design
KEIHIN SH7058 37805 Rxx HONDA
For a correct soldering procedure clean very well the soldering lay-by pins from the plastic film.
We suggest you to use a fine grit glass-paper smoothing by gentle pressure
the connection of the lay by pins.
https://ecu.design
KEIHIN SH7058 37805 Rxx HONDA
DIRECT CONNECTION – ECU TYPE 02 WRITING:
For the WRITING procedure use the FLAT cable F34NTF51
https://ecu.design
KEIHIN SH7058 37805 Rxx HONDA
For a correct soldering procedure clean very well the soldering lay-by pins from the plastic film.
We suggest you to use a fine grit glass-paper smoothing by gentle pressure the connection of the
lay by pins. Make the little short-circuits LINK1 & LINK2 on the opposite side of the ECU as shown
in the picture here below. After the writing operation, before placing back the ECU into the
vehicle, remove the LINK.
https://ecu.design
