Internal Use Only

North/Latin America http://aic.lgservice.com

Europe/Africa http://eic.lgservice.com
Asia/Oceania http://biz.lgservice.com

LED TV
SERVICE MANUAL
CHASSIS : LC31A

MODEL : 22MA33D 22MA33D-PZ(R)P

24MN33D 24MN33D-PZ(R)P

CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

P/NO : MFL67580673 (1301-REV00) Printed in Korea

 CONTENTS

CONTENTS . ............................................................................................. 2

SAFETY PRECAUTIONS.......................................................................... 3

SERVICING PRECAUTIONS..................................................................... 4

SPECIFICATION........................................................................................ 6

ADJUSTMENT INSTRUCTION............................................................... 11

TROUBLE SHOOTING............................................................................ 16

BLOCK DIAGRAM................................................................................... 23

EXPLODED VIEW .................................................................................. 24

SCHEMATIC CIRCUIT DIAGRAM ..............................................................

Copyright © LG Electronics. Inc. All right reserved. -2- LGE Internal Use Only
Only for training and service purposes
 SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the
Schematic Diagram and Exploded View.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent
Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

General Guidance Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.
An isolation Transformer should always be used during the
servicing of a receiver whose chassis is not isolated from the AC Do not use a line Isolation Transformer during this check.
power line. Use a transformer of adequate power rating as this Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
protects the technician from accidents resulting in personal injury between a known good earth ground (Water Pipe, Conduit, etc.)
from electrical shocks. and the exposed metallic parts.
Measure the AC voltage across the resistor using AC voltmeter
It will also protect the receiver and it's components from being with 1000 ohms/volt or more sensitivity.
damaged by accidental shorts of the circuitry that may be Reverse plug the AC cord into the AC outlet and repeat AC voltage
inadvertently introduced during the service operation. measurements for each exposed metallic part. Any voltage
measured must not exceed 0.75 volt RMS which is corresponds to
If any fuse (or Fusible Resistor) in this TV receiver is blown, 0.5mA.
replace it with the specified. In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
When replacing a high wattage resistor (Oxide Metal Film Resistor, repaired before it is returned to the customer.
over 1W), keep the resistor 10mm away from PCB.
Leakage Current Hot Check circuit
Keep wires away from high voltage or high temperature parts.
AC Volt-meter

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed Good Earth Ground
such as WATER PIPE,
metallic parts of the cabinet, such as antennas, terminals, etc., to CONDUIT etc.
To Instrument's
be sure the set is safe to operate without damage of electrical exposed
0.15µF
shock. METALLIC PARTS

Leakage Current Cold Check(Antenna Cold Check) 1.5 Kohm/10W

With the instrument AC plug removed from AC source, connect an
electrical jumper across the two AC plug prongs. Place the AC
When 25A is impressed between Earth and 2nd Ground
switch in the on position, connect one lead of ohm-meter to the AC for 1 second, Resistance must be less than 0.1
plug prongs tied together and touch other ohm-meter lead in turn to *Base on Adjustment standard
each exposed metallic parts such as antenna terminals, phone
jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.

Copyright © LG Electronics. Inc. All right reserved. -3- LGE Internal Use Only
Only for training and service purposes
 SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service unit under test.
manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES
SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as
NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or
following servicing precautions and any of the safety precautions on exposure of the assembly.
page 3 of this publication, always follow the safety precautions. 3. Use only a grounded-tip soldering iron to solder or unsolder ES
Remember: Safety First. devices.
4. Use only an anti-static type solder removal device. Some solder
General Servicing Precautions removal devices not classified as "anti-static" can generate
1. Always unplug the receiver AC power cord from the AC power electrical charges sufficient to damage ES devices.
source before; 5. Do not use freon-propelled chemicals. These can generate
a. Removing or reinstalling any component, circuit board electrical charges sufficient to damage ES devices.
module or any other receiver assembly. 6. Do not remove a replacement ES device from its protective
b. Disconnecting or reconnecting any receiver electrical plug or package until immediately before you are ready to install it.
other electrical connection. (Most replacement ES devices are packaged with leads
c. Connecting a test substitute in parallel with an electrolytic electrically shorted together by conductive foam, aluminum foil
capacitor in the receiver. or comparable conductive material).
CAUTION: A wrong part substitution or incorrect polarity 7. Immediately before removing the protective material from the
installation of electrolytic capacitors may result in an leads of a replacement ES device, touch the protective material
explosion hazard. to the chassis or circuit assembly into which the device will be
installed.
2. Test high voltage only by measuring it with an appropriate high CAUTION: Be sure no power is applied to the chassis or circuit,
voltage meter or other voltage measuring device (DVM, and observe all other safety precautions.
FETVOM, etc) equipped with a suitable high voltage probe. 8. Minimize bodily motions when handling unpackaged
Do not test high voltage by "drawing an arc". replacement ES devices. (Otherwise harmless motion such as
3. Do not spray chemicals on or near this receiver or any of its the brushing together of your clothes fabric or the lifting of your
assemblies. foot from a carpeted floor can generate static electricity
4. Unless specified otherwise in this service manual, clean sufficient to damage an ES device.)
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable General Soldering Guidelines
non-abrasive applicator; 10% (by volume) Acetone and 90% (by 1. Use a grounded-tip, low-wattage soldering iron and appropriate
volume) isopropyl alcohol (90%-99% strength) tip size and shape that will maintain tip temperature within the
CAUTION: This is a flammable mixture. range or 500 ˚F to 600 ˚F.
Unless specified otherwise in this service manual, lubrication of 2. Use an appropriate gauge of RMA resin-core solder composed
contacts in not required. of 60 parts tin/40 parts lead.
5. Do not defeat any plug/socket B+ voltage interlocks with which 3. Keep the soldering iron tip clean and well tinned.
receivers covered by this service manual might be equipped. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
6. Do not apply AC power to this instrument and/or any of its bristle (0.5 inch, or 1.25cm) brush with a metal handle.
electrical assemblies unless all solid-state device heat sinks are Do not use freon-propelled spray-on cleaners.
correctly installed. 5. Use the following unsoldering technique
7. Always connect the test receiver ground lead to the receiver a. Allow the soldering iron tip to reach normal temperature.
chassis ground before connecting the test receiver positive (500 ˚F to 600 ˚F)
lead. b. Heat the component lead until the solder melts.
Always remove the test receiver ground lead last. c. Quickly draw the melted solder with an anti-static, suction-
8. Use with this receiver only the test fixtures specified in this type solder removal device or with solder braid.
service manual. CAUTION: Work quickly to avoid overheating the circuit
CAUTION: Do not connect the test fixture ground strap to any board printed foil.
heat sink in this receiver. 6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
Electrostatically Sensitive (ES) Devices (500 ˚F to 600 ˚F)
Some semiconductor (solid-state) devices can be damaged easily b. First, hold the soldering iron tip and solder the strand against
by static electricity. Such components commonly are called the component lead until the solder melts.
Electrostatically Sensitive (ES) Devices. Examples of typical ES c. Quickly move the soldering iron tip to the junction of the
devices are integrated circuits and some field-effect transistors and component lead and the printed circuit foil, and hold it there
semiconductor "chip" components. The following techniques only until the solder flows onto and around both the
should be used to help reduce the incidence of component component lead and the foil.
damage caused by static by static electricity. CAUTION: Work quickly to avoid overheating the circuit
1. Immediately before handling any semiconductor component or board printed foil.
semiconductor-equipped assembly, drain off any electrostatic d. Closely inspect the solder area and remove any excess or
charge on your body by touching a known earth ground. splashed solder with a small wire-bristle brush.
Alternatively, obtain and wear a commercially available
discharging wrist strap device, which should be removed to
prevent potential shock reasons prior to applying power to the

Copyright © LG Electronics. Inc. All right reserved. -4- LGE Internal Use Only
Only for training and service purposes
IC Remove/Replacement CAUTION: Maintain original spacing between the replaced
Some chassis circuit boards have slotted holes (oblong) through component and adjacent components and the circuit board to
which the IC leads are inserted and then bent flat against the prevent excessive component temperatures.
circuit foil. When holes are the slotted type, the following technique
should be used to remove and replace the IC. When working with Circuit Board Foil Repair
boards using the familiar round hole, use the standard technique Excessive heat applied to the copper foil of any printed circuit
as outlined in paragraphs 5 and 6 above. board will weaken the adhesive that bonds the foil to the circuit
board causing the foil to separate from or "lift-off" the board. The
Removal following guidelines and procedures should be followed whenever
1. Desolder and straighten each IC lead in one operation by gently this condition is encountered.
prying up on the lead with the soldering iron tip as the solder
melts. At IC Connections
2. Draw away the melted solder with an anti-static suction-type To repair a defective copper pattern at IC connections use the
solder removal device (or with solder braid) before removing the following procedure to install a jumper wire on the copper pattern
IC. side of the circuit board. (Use this technique only on IC
Replacement connections).
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad and 1. Carefully remove the damaged copper pattern with a sharp
solder it. knife. (Remove only as much copper as absolutely necessary).
3. Clean the soldered areas with a small wire-bristle brush. 2. carefully scratch away the solder resist and acrylic coating (if
(It is not necessary to reapply acrylic coating to the areas). used) from the end of the remaining copper pattern.
3. Bend a small "U" in one end of a small gauge jumper wire and
"Small-Signal" Discrete Transistor carefully crimp it around the IC pin. Solder the IC connection.
Removal/Replacement 4. Route the jumper wire along the path of the out-away copper
1. Remove the defective transistor by clipping its leads as close as pattern and let it overlap the previously scraped end of the good
possible to the component body. copper pattern. Solder the overlapped area and clip off any
2. Bend into a "U" shape the end of each of three leads remaining excess jumper wire.
on the circuit board.
3. Bend into a "U" shape the replacement transistor leads. At Other Connections
4. Connect the replacement transistor leads to the corresponding Use the following technique to repair the defective copper pattern
leads extending from the circuit board and crimp the "U" with at connections other than IC Pins. This technique involves the
long nose pliers to insure metal to metal contact then solder installation of a jumper wire on the component side of the circuit
each connection. board.

Power Output, Transistor Device 1. Remove the defective copper pattern with a sharp knife.
Removal/Replacement Remove at least 1/4 inch of copper, to ensure that a hazardous
1. Heat and remove all solder from around the transistor leads. condition will not exist if the jumper wire opens.
2. Remove the heat sink mounting screw (if so equipped). 2. Trace along the copper pattern from both sides of the pattern
3. Carefully remove the transistor from the heat sink of the circuit break and locate the nearest component that is directly
board. connected to the affected copper pattern.
4. Insert new transistor in the circuit board. 3. Connect insulated 20-gauge jumper wire from the lead of the
5. Solder each transistor lead, and clip off excess lead. nearest component on one side of the pattern break to the lead
6. Replace heat sink. of the nearest component on the other side.
Carefully crimp and solder the connections.
Diode Removal/Replacement CAUTION: Be sure the insulated jumper wire is dressed so the
1. Remove defective diode by clipping its leads as close as it does not touch components or sharp edges.
possible to diode body.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.

Fuse and Conventional Resistor

Removal/Replacement
1. Clip each fuse or resistor lead at top of the circuit board hollow
stake.
2. Securely crimp the leads of replacement component around
notch at stake top.
3. Solder the connections.

Copyright © LG Electronics. Inc. All right reserved. -5- LGE Internal Use Only
Only for training and service purposes
 SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.

1. Application Range
This spec sheet is applied all of the TV used LC31A chassis.

2. Specification
Each part is tested as below without special appointment

1) Temperature : 25 ˚C ± 5 ˚C (77 ˚F ± 9 ˚F),

CST : 40 ˚C ± 5 ˚C
2) Relative Humidity : 65 % ± 10 %
3) Power Voltage : Standard input voltage
(100 V - 240 ­V ~, 50 / 60 Hz)
· Standard Voltage of each products is marked by models
4) Specification and performance of each parts are followed
each drawing and specification by part number in accord-
ance with BOM.
5) The receiver must be operated for about 5 minutes prior to
the adjustment.

3.Test method
1) Performance : LGE TV test method followed
2) Demanded other specification
- Safety : CE,IEC specification
- EMC : CE,IEC specification

Copyright © LG Electronics. Inc. All right reserved. -6- LGE Internal Use Only
Only for training and service purposes
4. General specification
4.1. TV
No Item Specification Remarks

1 Market EU/CIS (PAL Market-37 Countries) DTV & Analog (Total 37 countries)
DTV (MPEG2/4, DVB-T) :37 countries
UK/Italy/Germany/France/Spain/Sweden/Finland/Nether-
lands/ Belgium/Luxemburg/ Greece/Denmark/Czech/
Austria /Hungary/Swiss/Croatia/Turkey
Norway/Slovenia/Poland/Ukraine/Portugal/Ireland/Morocco/
Latvia/Estonia/Lithania/Rumania/Bulgaria/Russia/Slovakia
Bosnia/Serbia/Albania/Kazakhstan/Belarus
*4 Country, Nordic option(EU model only)
- Denmark , Finland, Norway, Sweden

DTV (MPEG2/4, DVB-T2): 8 countries

UK/Denmark/Sweden/Finland/Norway/Ireland/Ukraine/
Kazakhstan

DTV (MPEG2/4, DVB-C): 37 countries

UK/Italy/Germany/France/Spain/Sweden/Finland/Nether-
lands/ Belgium/Luxemburg/ Greece/Denmark/Czech/
Austria /Hungary/Swiss/Croatia/Turkey
Norway/Slovenia/Poland/Ukraine/Portugal/Ireland/Morocco/
Latvia/Estonia/Lithania/Rumania/Bulgaria/Russia/Slovakia
Bosnia/Serbia/Albania/Kazakhstan/Belarus

DTV (MPEG2/4,DVB-S): 29 countries

Italy/Germany/France/Spain/Netherlands/ Belgium/
Luxemburg/ Greece/ Czech/Austria /Hungary/Swiss/Croatia/
Turkey/Slovenia/Poland/Portugal/ Morocco/Latvia/
Estonia/Lithuania/Rumania/Bulgaria/Russia/Slovakia
Bosnia/Serbia/Albania/ Belarus

Supported satellite : 22 satellites

HISPASAT 1C/1D, ATLANTIC BIRD 2, NILESAT 101/102,
ATLANTIC BIRD 3, AMOS 2/3, THOR 5/6, IRIUS 4,
EUTELSAT-W3A, EUROBIRD 9A, EUTELSAT-W2A, HOT-
BIRD 6/8/9, EUTELSAT-SESAT, ASTRA 1L/H/M/KR, ASTRA
3A/3B, BADR 4/6, ASTRA 2D, EUROBIRD 3, EUTELSAT-
W7, HELLASSAT 2, EXPRESS AM1, TURKSAT 2A/3A,
INTERSAT10
2 Broadcasting system 1)Analogue TV Analogue TV : (RF) VHF: E2 to E12, UHF : E21 to E69
1) PAL-BG (CATV) S1 to S20, HYPER: S21 to S47
2) PAL-DK
3) PAL-I/I’ Digital TV : VHF, UHF
4) SECAM-BG
5) SECAM-DK Satellite TV : VHF, UHF, C-Band, Ku-Band
6) SECAM L/L’
* DVB-T2 ( T2 model only support )
Digital TV * DVB-S/S2 (Satellite model only support )
1) DVB-T/C/T2

Satellite Digital TV
1) DVB-T/C/S/S2

Copyright © LG Electronics. Inc. All right reserved. -7- LGE Internal Use Only
Only for training and service purposes
 No Item Specification Remarks

3 Receiving system Analog : Upper Heterodyne ► DVB-T

Digital : COFDM, QAM - Guard Interval (Bitrate_Mbit/s)
1/4, 1/8, 1/16, 1/32
- Modulation : Code Rate
QPSK : 1/2, 2/3, 3/4, 5/6, 7/8
16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8
► DVB-T2
- Guard Interval (Bitrate_Mbit/s)
1/4, 1/8, 1/16, 1/32, 1/128, 19/128, 19/256,
- Modulation : Code Rate
QPSK : 1/2, 2/5, 2/3, 3/4, 5/6
16-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
64-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
256-QAM : 1/2, 2/5, 2/3, 3/4, 5/6
► DVB-C
- Symbolrate :
4.0Msymbols/s to 7.2Msymbols/s
- Modulation :
16QAM, 64-QAM, 128-QAM and 256-QAM
► DVB-S/S2
- symbolrate
DVB-S2 (8PSK / QPSK) : 2 ~ 45Msymbol/s
DVB-S (QPSK) : 2 ~ 45Msymbol/s
- viterbi
DVB-S mode : 1/2, 2/3, 3/4, 5/6, 7/8
DVB-S2 mode : 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10
4 Scart Jack (1EA) PAL, SECAM Scart Jack is Full scart and support RF-OUT(analog)

5 Component Input (1EA) Y/Cb/Cr , Y/Pb/Pr

6 CVBS Input (1EA) PAL, SECAM, NTSC 4 System(Rear) :PAL, SECAM, NTSC, PAL60
CVBS Video input is used by common port with Component.
7 RGB Input RGB-PC Analog (D-SUB 15Pin)

8 HDMI Input (1EA) HDMI Rear / HDMI version 1.4/ support PC

Support HDCP
9 Audio Input (3EA) RGB/DVI Audio L/R Input
Component & CVBS CVBS Audio input is used by common port with Component.
SCART
10 USB (1EA) Picture, Music, Movie, SVC Software Update + Picture + Music + Movie

11 DVB DVB-T CI : UK, Finland, Denmark, Norway, Sweden, Russia, Spain,

Ireland, Luxemburg, Belgium, Netherland
CI+ : France(Canal+), Italy(DGTVi)
DVB-C CI : Switzerland, Austria, Slovenia, Hungary, Bulgaria
CI+: Switzerland(UPC,Cablecom), Netherland(Ziggo),
Germany(KDG,CWB),
Finland(labwise)

DVB-S CI + : Germany (Astra HD+)

12 Local Key (Touch) G

13 LAN JACK Modular 2xMN33V, 2xMA33V(Only UK for MHEG)

Copyright © LG Electronics. Inc. All right reserved. -8- LGE Internal Use Only
Only for training and service purposes
4.2. RGB/HDMI(PC) Specification
No Item Specification Remarks
1 Supported Sync. Type Separate Sync., Digital
2 Operating Frequency Analog Horizontal 30 ~ 61 kHz
Vertical 56 ~ 75 Hz
Digital Horizontal 30 ~ 61 kHz
Vertical 56 ~ 75 Hz
3 Resolution Analog Max. 1366x768 @ 60 Hz
Recommend 1366x768 @ 60 Hz
Digital Max. 1366x768 @ 60 Hz
Recommend 1366x768 @ 60 Hz
4 Operating Environment Temp : 10 ˚C ~ 35 ˚C
Humidity : 20 % ~ 80 %
5 Storage Environment Temp : -10 ˚C ~ 60 ˚C non condensing
Humidity : 5 % ~ 90 % non condensing

5. Timing
5.1. RGB/ HDMI (PC)
No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Remark
1 720*400 31.468 70.080 28.321
2 640*480 31.469 59.940 25.175
3 640*480 37.500 75.000 31.500
4 800*600 37.879 60.317 40.000
5 800*600 46.875 75.000 49.500
6 1024*768 48.363 60.004 65.000
7 1024*768 60.023 75.029 78.750
8 1280*800 49.702 59.810 83.500
9 1366*768 47.717 59.79 85.5

Copyright © LG Electronics. Inc. All right reserved. -9- LGE Internal Use Only
Only for training and service purposes
5.2. HDMI (DTV)
No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Remark
1 720* 480 31.469 / 31.5 59.94 / 60 27.00/ 27.03 SDTV 480P
2. 720*576 31.25 50.00 27.864 SDTV 576P
3. 1280*720 37.50 50.00 74.250 HDTV 720P
4 1280* 720 44.96 / 45 59.94 / 60 74.17/ 74.25 HDTV 720P
5 1920* 1080 33.72 / 33.75 59.94 / 60 74.17/ 74.25 HDTV 1080I
6 1920* 1080 28.125 50.00 74.25 HDTV 1080I
7 1920* 1080 27.00 24 74.25 HDTV 1080P
8 1920* 1080 33.75 30.00 74.25 HDTV 1080P
9 1920* 1080 56.250 50 148.5 HDTV 1080P
10 1920* 1080 67.43 / 67.5 59.94 / 60 148.35/ 148.50 HDTV 1080P

5.3. Component
Specification
No Remark
Resolution H-freq(kHz) V-freq(Hz) Pixel clock( MHz)
1. 720* 480 15.73 59.94 13.500 SDTV, DVD 480I( 525I)
2. 720* 480 15.75 60.00 13.514 SDTV, DVD 480I( 525I)
3. 720* 576 15.625 50.00 13.500 SDTV, DVD 576I( 625I) 50Hz
4. 720* 480 31.47 59.94 27.000 SDTV 480P
5. 720* 480 31.50 60.00 27.027 SDTV 480P
6. 720* 576 31.25 50.00 27.000 SDTV 576P 50Hz
7. 1280* 720 44.96 59.94 74.176 HDTV 720P
8. 1280* 720 45.00 60.00 74.250 HDTV 720P
9. 1280* 720 37.50 50.00 74.25 HDTV 720P 50Hz
10. 1920* 1080 33.72 59.94 74.176 HDTV 1080I
11. 1920* 1080 33.75 60.00 74.250 HDTV 1080I
12. 1920* 1080 28.125 50.00 74.250 HDTV 1080I 50Hz
13. 1920* 1080 56.25 50 148.5 HDTV 1080P
14. 1920* 1080 67.432 59.94 148.350 HDTV 1080P
15. 1920* 1080 67.5 60.00 148.5 HDTV 1080P

Copyright © LG Electronics. Inc. All right reserved. - 10 - LGE Internal Use Only
Only for training and service purposes
 ADJUSTMENT INSTRUCTION
1. Application Range 4) Click “Read” tab, and then load download file(XXXX.bin) by
clicking “Read”
This document is applied to LC31A chassis TV which is manu-
factured in TV (or Monitor) Factory or is produced on the basis (4)
of this data.
filexxx.bin

2. Designation
1) The adjustment is according to the order which is designat-
ed and which must be followed, according to the plan which
can be changed only on agreeing.
2) Power adjustment : Free Voltage.
3) Magnetic Field Condition: Nil. 5) Click “Auto” tab and set as below
4) Input signal Unit: Product Specification Standard. 6) Click “Run”.
5) Reserve after operation: Above 5 Minutes (Heat Run) 7) After downloading, check “OK” message.
Temperature : at 25 °C ± 5 °C
Relative humidity : 65 % ± 10 % (5)
Input voltage : 220 V, 60 Hz
6) Adjustment equipments : Color Analyzer (CA-210 or CA- (5)
110), DDC Adjustment Jig equipment, SVC remote control-
ler. (7) ……….OK
7) Push The "IN STOP KEY" – For memory initialization
Case1 : Software version up (6)
1) After downloading S/W by USB , Multi-vision set will
reboot automatically
2) Push "In-stop" key
3) Push "Power on" key
4) Function inspection * USB DOWNLOAD(*.epk file download)
5) After function inspection, Push "In-stop" key. 1) Make New folder named “LG_DTV” and put ISP file(*.epk)
in the folder.
Case2 : Function check at the assembly line 2) Put the USB Stick to the USB socket.
1) When TV set is entering on the assembly line, Push "In- 3) Automatically detecting update file in USB Stick
stop" key at first. - If your downloaded program version in USB Stick is
2) Push "Power on" key for turning it on. Low, it didn’t work. But your downloaded version is
→ If you push "Power on" key, TV set will recover channel High, USB data is automatically detecting.
information by itself. 4) Show the message “Copy the file from the Memory…”
3) After function inspection, Push "In-stop" key.

3. Main PCB check process

* APC - After Manual-Insult, executing APC
5) Updating is starting.

* Boot file Download

1) Execute ISP program “Mstar ISP Utility” and then click
“Config” tab.
2) Set as below, and then click “Auto Detect” and check “OK”
message. If display “Error”, Check connect computer, jig,
and set.
3) Click “Connect” tab. If display “Can’t ”, Check connect 6) Updating Completed, The TV will restart automatically.
computer, jig, and set. 7) If your TV is turned on, check your updated version and
(1) (3) Tool option. (explain the Tool option, next stage)
* If downloading version is more high than your TV
Please Check the Speed :
have, TV can lost all channel data. In this case, you
Use the speed under have to channel recover. if all channel data is cleared,
200KHz. you didn’t have a DTV/ATV test on production line.
(2) OK

Copyright © LG Electronics. Inc. All right reserved. - 11 - LGE Internal Use Only
Only for training and service purposes
3.1. EDID Process 3.1.2. RGB EDID Data
3.1.1. EDID download - All Models (Product ID:22984/HEXA: 59C8)
1) Press "Power only" key of service remote control.
2) Press the ADJ KEY on R/C and enter EZ ADJUST
3) Enter EDID D/L mode by pushing "►" key at "EDID D/L".
4) EDID download is executed automatically.
5) Press EXIT key on R/C.
GG
WUG{––“Gv—›–•XG
WUG{––“Gv—›–•XG GG GG
XUG{––“Gv—›–•YG
XUG{––“Gv—›–•YG GG GG
YUG{––“Gv—›–•ZG
YUG{––“Gv—›–•ZG GG GG
ZUG{––“Gv—›–•[G
ZUG{––“Gv—›–•[G GG GG
[UG{––“Gv—›–•\G
[UG{––“Gv—›–•\G
\UG{––“Gv—›–•]G
\UG{––“Gv—›–•]G
GG
GG
GG
GG
*(week), **(year), ***(Check sum) : Adjustable Data
]UGj–œ•›™
]UGj–œ•›™ Gn™–œ—G
Gn™–œ—G : Screen size, : Color Characteristics
^UGh™ŒˆGv—›–•G
^UGh™ŒˆGv—›–•G GG GG
_UGhkjGjˆ“‰™ˆ›–•G
_UGhkjGjˆ“‰™ˆ›–•G
`UG~›ŒGiˆ“ˆ•ŠŒG
`UG~›ŒGiˆ“ˆ•ŠŒG GG GG 3.1.3. HDMI EDID Data
XWUGXWGw–•›G~iG
XWUGXWGw–•›G~iGGG
XXUG{Œš›Gwˆ››Œ™•G
XXUG{Œš›Gwˆ››Œ™•GGGGG
GG
GG
GG
GG
- All Models (Product ID :22986/HEXA:59CA)
XYUGlkpkGkVsG
XYUGlkpkGkVsG ඖG
ඖG GG lkpkGkVsG
lkpkGkVsG
XZUGzœ‰GiVjG
XZUGzœ‰GiVjG GG GG oktpXG
oktpXGGGGGGGGGGGGGGGGGGGGGGGvrG
vrG GG GG
X[UG{–œŠGzŒ•š››
X[UG{–œŠGzŒ•š›› GzŒ››•ŽG
GzŒ››•ŽG yniG
yniGGGGGGGGGGGGGGGGGGGGGGGGGGGvrG
vrG GG GG
X\UGlŸ›UGp•—œ›Gh‹‘œš›G
X\UGlŸ›UGp•—œ›Gh‹‘œš›G GG GG GG
X]UGzwrGs—š
X]UGzwrGs—š •ŠGh‹‘œš›G
•ŠGh‹‘œš›G GG
X^UzwkpmGs—š
X^UzwkpmGs—š •ŠGh‹‘œš›G
•ŠGh‹‘œš›G GG z›ˆ™›G
z›ˆ™›G GG yŒšŒ›G
yŒšŒ›G GG
GG GG GG GG

→ Caution: - Never connect HDMI & D-sub Cable when

download EDID.
-D ownload HDMI1

* Edid data and Model option download (USB)

NO Item CMD CMD Data 0
1 2

Enter Download A A 0 0 When transfer the

download ‘Mode In’ ‘Mode In’,
MODE Carry the command.

EDID data and Download A E 00 10 Automatically download

Model option (The use of a internal
download Data) *(week), **(year), ***(Check sum) : Adjustable Data
**** (physical address) : (HDMI : 10),
****(Check sum) : (HDMI : CE)
: Screen size, : Color Characteristics

3.2. Function Check

3.2.1. Check display and sound
*Check Input and Signal items. (cf. work instructions)
1) TV
2) AV (SCART/CVBS)
3) COMPONENT (480i)
4) RGB(PC : 1366 x 768 @ 60 Hz)
5) HDMI(PC : 1366 x 768 @ 60Hz)
6) PC Audio In
* Display and Sound check is executed by Remote controller

→ Caution : Not to push the INSTOP KEY after completion if

the function inspection.

Copyright © LG Electronics. Inc. All right reserved. - 12 - LGE Internal Use Only
Only for training and service purposes
3.3. CI+ key writing process. 4. Total Assembly line process
(Device CN) 4.1. Tool option & ADC Check
3.3.1. Download method 1) Press "Power on" key of service remote control.
3.3.1.1. Communication Prot Connection 2) Connect USB Port → USB to Serial Adapter (UC-232A) →
RS-232C cable → PC(RS-232C port)
3) Check the 'Tool Option' (Refer to the BOM Comments or
Adjustment spec)
4) Check the ‘ADC’ is ok.
4.2. M
 odel name & Serial number Down-
load
4.2.1. Model name & Serial number D/L
Connection : PCBA (USB Port) → USB to Serial Adapter (UC- 1) Press "Power on" key of service remote control.
232A) → RS-232C cable → PC(RS-232C port) 2) Connect USB Port → USB to Serial Adapter (UC-232A) →
→ Caution : LD31Q/LD31A chassis support only UC-232A RS-232C cable → PC(RS-232C port)
driver. ( only use this one. ) 3) Write Model Name & Serial Number by use USB Port
4) Must check the serial number at the Diagnostics of SET UP
3.3.2. CI+ Key Download menu. (Refer to below).
1) Set CI+ Key path Directory at Start Mac & CI+ Download
Programme.

4.2.2. Method & notice

1) Model Name & Serial Number D/L is using of scan equip-
ment.
2) Setting of scan equipment operated by Manufacturing
Technology Group.
3) Serial number D/L must be conformed when it is produced
in production line, because serial number D/L is mandatory
2) Set COM 1,2,3,4 / 115200(Baudrate) (1)/(2) by D-book 4.0
3) Click port connection button(1)
4) Start CI+ Key Download, Push the button(4) * Manual Download (Model Name and Serial
5) Check OK or NG. Number)
6) After completing download, CI + key values are increase by If the TV set is downloaded By OTA or Service man, Some-
one automatically. To write CI+ key next SET, click CI+ key times model name or serial number is initialized.( Not always)
writing button(5) directly. There is impossible to download by bar code scan, so It need
7) Check whether the key was downloaded or not at ‘In Start’ Manual download.
menu. (Refer to below). 1) Press the 'Instart' key of ADJ remote controller.
2) Go to the menu 'Model Number D/L' like below photo.
3) Input the Factory model name(ex 27MD73D-PZP) or Serial
number like photo.

4) Check the model name Instart menu → Factory name

displayed (ex 27MD73D-PZP)
5)Check the Diagnostics (DTV country only) → Buyer model
displayed (ex 27MD73D-PZ)

Copyright © LG Electronics. Inc. All right reserved. - 13 - LGE Internal Use Only
Only for training and service purposes
4.3. Function Check 4.4. White balance adjustment
4.3.1. Check display and sound -Equipment
*Check Input and Signal items. (cf. work instructions) 1) Color Analyzer: CA-210 (LED Module : CH 14)
1) TV 2) Adj. Computer(During auto adj., RS-232C protocol is
2) AV (SCART/CVBS) needed)
3) COMPONENT (480i) 3) Adjust Remocon
4) RGB(PC : 1366 x 768 @ 60 Hz)
5) HDMI(PC : 1366 x 768 @ 60Hz) RGB Gains are fixed data for each model. Insert RS-232C
6) PC Audio In Jack which is connected with PC for White Balance or equiva-
* Display and Sound check is executed by Remote controller lent device.
* Total Assembly line should be check whether the color
→ Caution : N
 ot to push the INSTOP KEY after completion if the coordinate(x,y) data refer to below table were meet or not.
function inspection. Color Cool 13,000 °K X=0.276 (±0.03) <Test Signal>
Temperature Y=0.275 (±0.03) Inner pattern
(204gray,80IRE)
4.3.2. PCMCIA CARD Check Medium 9,300 °K X=0.290 (±0.03)
Y=0.298 (±0.03)
You must adjust DTV 29 Channel and insert PCMCIA CARD
to socket. Warm 6,500 °K X=0.318 (±0.03)
Y=0.334 (±0.03)
- If PCMCIA CARD works normally, video signals will appear
on screen. Luminance Cool Min : 80 Typ : 110 <Test Signal>
(cd/m²) Inner pattern
But it works abnormally, "No CA module" will appear on Medium Min : 80 Typ : 110 (204gray,80IRE)
screen. Warm Min : 70 Typ : 110
→ Caution: Set up "RF mode" before launching products.

*Note : x ,y coordinates are drifted about 0.007 after 30 mins

heat-run. So checking color coordinate within 5-min at
4.3.3. PIP Check
total assembly line, consider x,y coordinates might be
1) Press "Power on" key of service remote control.
up to 0.007 than x,y target of each color temperature.
2) Input RGB & TV(ATV or DTV) signal.
3) Set Input mode to RGB.
*Note : Manual W/B process using adjusts Remote control.
4) Press ‘PIP" key of ADJ remote controller
1) After enter Service Mode by pushing "ADJ" key,
5) Check TV Video & Audio signal of Sub picture.
2) Enter "White Balance" by pushing "►" key at "White Bal-
ance".
G
WUG{––“Gv—›–•XG G G
XUG{––“Gv—›–•YG G G
YUG{––“Gv—›–•ZG G G
ZUG{––“Gv—›–•[G G G
[UG{––“Gv—›–•\G G G
\UG{––“Gv—›–•]G
]UGj–œ•›™ Gn™–œ—G G G ~›ŒGiˆ“ˆ•ŠŒG
^UGh™ŒˆGv—›–•G G G j–“–™G{Œ”—UG ඔG j––“G ඖG
_UGhkjGjˆ“‰™ˆ›–•G G G G G G G G G yTnˆ•G G XWWG G
`UG~›ŒGiˆ“ˆ•ŠŒG G G G G G G G G G ඖG G G nTnˆ•G G XW[G G
XWUGXWGw–•›G~iG G G G iTnˆ•G G X`YG G
XXUG{Œš›Gwˆ››Œ™•G G G G G yTjœ›G G ][G G
XYUGlkpkGkVsG G G G G G G G G G G G G G G G nTjœ›G G ][G G
XZUGzœ‰GiVjG G G iTjœ›G G ][G G
X[UG{–œŠGzŒ•š›› GzŒ››•ŽG {Œš›Twˆ››Œ™•G G vuG G
X\GlŸ›UGp•—œ›Gh‹‘œš›G iˆŠ’“Ž›G G XWWG G
G G G yŒšŒ›G G {–GzŒ›G G

* When doing Adjustment, Please make circumstance as

below.

Copyright © LG Electronics. Inc. All right reserved. - 14 - LGE Internal Use Only
Only for training and service purposes
4.5. DPM Operation check
■ Measurement Condition: 100~240V@ 50/60Hz
1) Set Input to RGB-PC and connect D-sub cable to set –
RGB Mode
Set Input to HDMI (with Input Label set to PC) and con-
nect HDMI cable to set – HDMI Mode
2) Cut off H sync or V sync of signal.
3) Check DPM operation refer to the below table.
Operating Condition Sync Video LED Wattage
(H/V) (SET) (W)
Power S/W On Sleep mode - Off/Off Off Amber 1
RGB,HDMI

4.6. Model Name & SW Version & Adjust check.

* Press the ‘Instart’ key of ADJ remote controller
4.6.1. Model Name& SW Version Check
1) Check ‘Model Name’.
2) Check ‘S/W Version’ (Refer to the IC Ver. in the BOM)

4.6.2. Adjust Check

1) Check ‘Country Group’
2) Check ‘Area Option’
3) Check ‘Tool Option’ (Refer to the BOM Comments)
4) Check ‘Adjust ADC[Comp&RGB]’ is OK.
5) Check ‘EDID[RGB&HDMI]’ is OK.
* After check all, Press the 'EXIT' key of ADJ remote controller
to go out SVC menu.

Copyright © LG Electronics. Inc. All right reserved. - 15 - LGE Internal Use Only
Only for training and service purposes
 TROUBLE SHOOTING
1. No Power
N Check Power connector N
Check C802 All Replace Adapter
Voltage Level (19V) OK ?

Check IC2602 Output N

Replace IC2602
Voltage Level (3.3V_ST)

Y
N Replace IC802 &
Check IC802 output
Voltage Level (5V) Recheck

Check IC800 Output N

Replace IC800
Voltage Level (5V)

Check IC810 Output N

Replace IC810
Voltage Level (2.5V)

Check IC803 Output N

Replace IC800
Voltage Level (3.3V)

Check IC807 Output N

Replace IC807
Voltage Level (1.5V)

Check IC805 Output N

Replace IC805
Voltage Level (1.8V)

Check IC801 Output N

Replace IC801
Voltage Level (1.23V)

Check IC806 Output N

Replace IC806
Voltage Level (1.24V)

Check X201 Clock N

Replace X201
24MHz

Replace IC100 Flash Memory

Copyright © LG Electronics. Inc. All right reserved. - 16 - LGE Internal Use Only
Only for training and service purposes
2. No Picture
N Check WLED_ENABLE high N Check IC101
Module
Back Light On ? R155 Replace Main Scaler IC

Y Y

Check LED Driver output N Check LED Driver IC1100

(LED Driver B’d P1101 #1,2,5,6) Replace LED Driver IC

Check Panel power N

P1002(#1,2,3) 5V Replace IC802
IC802 Output 5V

Y
N Check IC101
Check Panel clock
P1002(#10,11,22,23) Repair Main B/D

Check FFC Cable for damage N

Replace Cable
or open conductors.

Replace T-con
Board or module

Copyright © LG Electronics. Inc. All right reserved. - 17 - LGE Internal Use Only
Only for training and service purposes
3. No Video - Digital TV
Check RF Cable

N
1. Check Tuner(TU2603 #5) Power (3.3V) Replace IC803
2. Check IC803 Output voltage(3.3V)

N
1. Check Tuner(TU2602 #7) Power (1.8V) Replace IC805
2. Check IC805 Output voltage(1.8V)

N
Check Tuner(TU2602) I2C Signal Check IC101
SCL(R2609), SDA(R2610)

N
Check Tuner(TU2603) Replace Tuner(TU2603)
Data, CLK, SYN, VAL Recheck

Copyright © LG Electronics. Inc. All right reserved. - 18 - LGE Internal Use Only
Only for training and service purposes
4. No Video - Component
Check input signal format
Is it supported?
Y

Wave form of Comp Y Wave form of Comp Pb Wave form of Comp Pr

Check Component Cable

N Replace JK400 or
Check JK400 Check Device

Check signal N Replace R239,R237,R241

R239,R237,R241
C220,C218,C222
C220,C218,C222

IC101 has problem

Wave form of C220 Wave form of C218 Wave form of C222

Copyright © LG Electronics. Inc. All right reserved. - 19 - LGE Internal Use Only
Only for training and service purposes
5. No Video - RGB
Check input signal format
Is it supported?

Check RGB Cable

Y
N Replace JK406 or
Check JK406 Check Device
Y

Check Hsync, Vsync N

Replace R4024, R4025
R4024, R4025

Check signal RGB N Replace R228,R230,R232

R228,R230,R232 C204,C206,C208
C204,C206,C208
Y

IC101 has problem

Wave form of R4025(Vsync) Wave form of R4024(Hsync)

Wave form of R228/C204 Wave form of R230/C206 Wave form of R232/C208

Copyright © LG Electronics. Inc. All right reserved. - 20 - LGE Internal Use Only
Only for training and service purposes
6. No Video - HDMI
Check input signal format
Is it supported?
Y

Check HDMI Cable for damage

or open connector
Y

Check JK600/JK601 N
Replace connector
for proper connection or damage
Y

Check I2C Signal (JK600/601) N

(#15, #16) Re download EDID data

N
Check HDCP Key (IC101) Replace Scaler(IC101)

Copyright © LG Electronics. Inc. All right reserved. - 21 - LGE Internal Use Only
Only for training and service purposes
7. No Audio
Make sure you can’t hear any audio and
Device support the audio signal normally.
Y

Check Speaker and N

its wire connection (JK700) Replace connector or Speaker
and the resistance

N
Check R879 Voltage Level (3.3V) Replace IC807(3.3V)

Check Signal from IC700 N

Replace IC700
L700,L701, L706, L709

Check Signal from IC101 N

SDA/SCL Replace IC101
(R703/R214, R707/R213)

Copyright © LG Electronics. Inc. All right reserved. - 22 - LGE Internal Use Only
Only for training and service purposes
 BLOCK DIAGRAM

Copyright © LG Electronics. Inc. All right reserved. - 23 - LGE Internal Use Only
Only for training and service purposes
 EXPLODED VIEW
IMPORTANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts
are identified by in the Schematic Diagram and EXPLODED VIEW.
It is essential that these special safety parts should be replaced with the same components as recommended
in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.

910
400

900
535
LV1

820
A2

120
540

810

121
800
200

511

302
510
300

301

Copyright © LG Electronics. Inc. All right reserved. - 24 - LGE Internal Use Only
Only for training and service purposes
 IC102
H27U1G8F2CTR-BC
NAND FLASH MEMORY +3.3V_Normal
<CHIP Config(LED_R/BUZZ)>
+3.3V_Normal
Boot from SPI CS1N(EXT_FLASH) 1’b0
NC_1
1 48
NC_29 Boot from SPI_CS0N(INT_FLASH) 1’b1
NAND_1G_HYNIX_9103(DEV) IC101
NC_2 EAN35669103 NC_28
2 47 MSD804KKX
NC_3 NC_27 PCM_A[0-7] <CHIP Config>
3 46 PCM_D[0-7]
22 (I2S_OUT_BCK,I2S_OUT_MCK,PAD_PWM1PAD_PWM0)
NC_4 NC_26 S7LR-M_NON_MS10
4 45 AR101 B51_no_EJ : 4’b0000 Boot from 8051 with SPI flash PCM_D[0] W21
22 SB51_WOS : 4’b0001 Secure B51 without scramble PCMDATA[0]/GPIO129
NC_5 I/O7 PCM_A[7] PCM_D[1] AA18
R109 5 44
AR103 R107 3.9K SB51_WS : 4’b0010 Secure B51 with scramble PCM_D[2] PCMDATA[1]/GPIO130
1K NC_6 I/O6 PCM_A[6] MIPS_SPE_NO_EJ : 4’b0100 Boot from MIPS with SPI flash AB22
6 43 PCM_D[3] PCMDATA[2]/GPIO131
MIPS_SPI_EJ_1 : 4’b0101 Boot from MIPS with SPI flash AE20
R/B I/O5 PCM_A[5] MIPS_SPI_EJ_2 : 4’b0110 Boot from MIPS with SPI flash PCM_D[4] PCMDATA[3]/GPIO123
7 42 AA15
/F_RB MIPS_WOS : 4’b1001 Secure MIPS without scramble PCMDATA[4]/GPIO122
RE I/O4 PCM_A[4] MIPS_WS : 4’b1010 Scerur MIPS with SCRAMBLE PCM_D[5] AE21
8 41 PCM_D[6] PCMDATA[5]/GPIO121
/PF_OE +3.3V_Normal AB21 AE18
+3.3V_ST PCMDATA[6]/GPIO120 NF_CE1Z/GPIO141
CE NC_25 PCM_D[7] Y15 AC17
/PF_CE0 9 40 PCM_A[0-14] PCMDATA[7]/GPIO119 NF_WPZ/GPIO196 /PF_WP
NC_7 NC_24 AD18
10 39 PCM_A[0] NF_CEZ/GPIO140 /PF_CE0
C102 W20 AC18

4.7K

4.7K

4.7K

4.7K
OPT PCMADR[0]/GPIO128 NF_CLE/GPIO139 /PF_CE1

4.7K
NC_8 NC_23 10uF PCM_A[1]

4.7K
R152
V20 AC19

OPT
R108 C101 11 38
1K PCM_A[2] PCMADR[1]/GPIO127 NF_REZ/GPIO142 /PF_OE
0.1uF VCC_1 VCC_2 W22 AD17

10V

OPT

OPT

OPT
12 37 PCM_A[3] PCMADR[2]/GPIO125 NF_WEZ/GPIO143 /PF_WE

OPT
AB18 AE17
+3.3V_Normal VSS_1 VSS_2 C103 R103 0 PCM_A[4] PCMADR[3]/GPIO124 NF_ALE/GPIO144 PF_ALE

R115

R117

R165

R123
0.1uF AA20 AD19

R142
13 36 LED_AMBER
OPT PCM_A[5] PCMADR[4]/GPIO102 NF_RBZ/GPIO145 /F_RB
NC_9 NC_22 R100 OPT 0 AA21 +3.3V_ST
R105 PCMADR[5]/GPIO104
1K 14 35 LED_RED PCM_A[6] Y19
22 PCMADR[6]/GPIO105

R125
NC_10 NC_21 PCM_A[7] AB17
AR104 15 34 SPI_SDI

10K
PCM_A[8] PCMADR[7]/GPIO106
CLE NC_20 Y16
16 33 AUD_SCK PCM_A[9] PCMADR[8]/GPIO111
/PF_CE1 AR102 AUD_MASTER_CLK R148 AB19
PCMADR[9]/GPIO113 GPIO_PM[0]/GPIO6
H5
DSUB_DET
ALE I/O3 PCM_A[3] AUD_MASTER_CLK_0 PCM_A[10] AB20 K6
PF_ALE 17 32 33
OPT PCM_A[11] PCMADR[10]/GPIO117 PM_UART_TX/GPIO_PM[1]/GPIO7 PM_TXD
WE I/O2 PCM_A[2] PWM1 AA16 K5
18 31 C112 PCM_A[12] PCMADR[11]/GPIO115 GPIO_PM[2]/GPIO8 5V_DET_HDMI_2
/PF_WE PWM0 AA19 J6
WP I/O1 PCM_A[1] 100pF PCM_A[13] PCMADR[12]/GPIO107 GPIO_PM[3]/GPIO9 MULTI_ON

4.7K

4.7K

4.7K

4.7K

4.7K

4.7K
19 30 50V AC21 K4
/PF_WP PCM_A[14] PCMADR[13]/GPIO110 GPIO_PM[4]/GPIO10 POWER_ON/OFF1
NC_11 I/O0 PCM_A[0] AA17 L6
20 29 PCMADR[14]/GPIO109 PM_UART_RX/GPIO_PM[5]/GPIO11 PM_RXD

OPT

OPT
R106 C2
22 PM_SPI_SCZ1/GPIO_PM[6]/GPIO12

0.1uF
R128
1K NC_12 NC_19

OPT

50V
47K

C113
Y20 L5

R116

R118

R121

R124

R143

R153
21 28
R102 /PCM_REG PCMREG_N/GPIO126 GPIO_PM[7]/GPIO13 /FLASH_WP
NC_13 NC_18 M6
3.3K 22 27 GPIO_PM[8]/GPIO14 HP_MUTE
AB15 M5
NC_14 NC_17 /PCM_OE PCMOE_N/GPIO116 GPIO_PM[9]/GPIO15 PANEL_CTL
23 26 AA22 C1
/PCM_WE PCMWE_N/GPIO195 PM_SPI_SCZ2/GPIO_PM[10]/GPIO16 5V_DET_HDMI_1
NC_15 NC_16 AD22 M4
24 25 /PCM_IORD PCMIORD_N/GPIO114 GPIO_PM[11]/GPIO17 NTP_MUTE
AD20
/PCM_IOWR PCMIOWR_N/GPIO112 +3.3V_ST 120915
A2 R147 33 Pull up added
PM_SPI_SCK/GPIO1 SPI_SCK
AD21 D3 R146 33 R180
/PCM_CE PCMCE_N/GPIO118 PM_SPI_CZ0/GPIO_PM[12]/GPIO0 /SPI_CS 4.7K
AC20 B2
/PCM_IRQA PCMIRQA_N/GPIO108 PM_SPI_SDI/GPIO2 SPI_SDI
Y18 B1 R151 33
/PCM_CD PCMCD_N/GPIO133 PM_SPI_SDO/GPIO3 SPI_SDO
Y21
/PCM_WAIT PCMWAIT_N/GPIO103 for SERIAL FLASH
Y22
PCM_RST PCM_RESET/GPIO132
CI_TS_CLK
NAND_1G_SS NAND_1G_NUMONYX(DEV) Y14
TS0CLK/GPIO90 CI_TS_VAL
EAN61857001 EAN60762401 U21 AA10 CI_TS_SYNC
USB_OCD PCM2_CE_N/GPIO134 TS0VALID/GPIO88
IC102-*1 IC102-*2 LGE2121-NonMS10 (MSD804KKX) V21 Y12
CI_TS_DATA[0-7]
K9F1G08U0D-SCB0 NAND01GW3B2CN6E USB_CTL PCM2_IRQA_N/GPIO135 TS0SYNC/GPIO89
: EAN62651201 (KR/US REGION) R20
PCM2_CD_N/GPIO138 CI_TS_DATA[0]
T20 Y13 from CI SLOT
PCM_5V_CTL PCM2_WAIT_N/GPIO136 TS0DATA_[0]/GPIO80 CI_TS_DATA[1]
NC_1 NC_29 NC_1 NC_29 LGE2121-MS10 (MSD804KKX) U22 Y11
1 48 1 48 PCM2_RESET/GPIO137 TS0DATA_[1]/GPIO81 CI_TS_DATA[2]
: EAN62674101 (NON_KR/US REGION) AA12
NC_2 NC_28 NC_2 NC_28 TS0DATA_[2]/GPIO82 CI_TS_DATA[3]
2 47 2 47 S7LR-M_MS10(NON KR/US)
120917 D4 AB12
IC101-*1 /MHL_OCP_DET UART1_TX/GPIO46 TS0DATA_[3]/GPIO83 CI_TS_DATA[4]
NC_3 NC_27 NC_3 NC_27
LGE2121-MS (M1_L13_MS10) Changed E4 AA14
3 46 3 46 MHL_OCP_EN UART1_RX/GPIO47 TS0DATA_[4]/GPIO84 CI_TS_DATA[5]
W21
N25 AB14
NC_4 NC_26 NC_4 NC_26 AA18
PCMDATA[0]/GPIO129
PM_TXD UART2_TX/GPIO68 TS0DATA_[5]/GPIO85 CI_TS_DATA[6]
4 45 4 45 AB22
PCMDATA[1]/GPIO130
PCMDATA[2]/GPIO131
N24 AA13
AE20
AA15
PCMDATA[3]/GPIO123 PM_RXD UART2_RX/GPIO67 TS0DATA_[6]/GPIO86 CI_TS_DATA[7]
NC_5 I/O7 NC_5 I/O7 AE21
PCMDATA[4]/GPIO122 B8 AB11
5 44 5 44 AB21
PCMDATA[5]/GPIO121
AE18 MODEL_OPT_6 UART3_TX/GPIO50 TS0DATA_[7]/GPIO87
Y15
PCMDATA[6]/GPIO120
PCMDATA[7]/GPIO119
NF_CE1Z/GPIO141
NF_WPZ/GPIO196
AC17
for SYSTEM EEPROM A8 FE_TS_CLK
NC_6 I/O6 NC_6 I/O6 W20
NF_CEZ/GPIO140
AD18
AC18
MODEL_OPT_7 UART3_RX/GPIO51 FE_TS_VAL_ERR
6 43 6 43 V20
PCMADR[0]/GPIO128 NF_CLE/GPIO139
AC19 (IC104) AC15
W22
PCMADR[1]/GPIO127 NF_REZ/GPIO142
AD17 TS1CLK/GPIO101 FE_TS_SYNC
R/B I/O5 RB I/O5 AB18
PCMADR[2]/GPIO125
PCMADR[3]/GPIO124
NF_WEZ/GPIO143
NF_ALE/GPIO144
AE17
R136 22 P23 AD15
7 42 7 42
AA20
AA21
PCMADR[4]/GPIO102 NF_RBZ/GPIO145
AD19
I2C_SCL I2C_SCKM2/DDCR_CK/GPIO75 TS1VALID/GPI99 FE_TS_DATA[0-7]
Y19
PCMADR[5]/GPIO104 R137 22 P24 AC16
RE I/O4 R I/O4 AB17
PCMADR[6]/GPIO105
PCMADR[7]/GPIO106
I2C_SDA I2C_SDAM2/DDCR_DA/GPIO74 TS1SYNC/GPIO100
Y16
8 41 8 41 PCMADR[8]/GPIO111

CE
AB19
AB20
PCMADR[9]/GPIO113
PCMADR[10]/GPIO117
GPIO_PM[0]/GPIO6
PM_UART_TX/GPIO_PM[1]/GPIO7
H5
K6
D2 AD16 FE_TS_DATA[0] Internal demod out
NC_25 E NC_25 AA16 K5
RGB_DDC_SDA
9 40 9 40 AA19
PCMADR[11]/GPIO115 GPIO_PM[2]/GPIO8
J6 DDCA_DA/UART0_TX TS1DATA_[0]/GPIO91 FE_TS_DATA[1]
AC21
PCMADR[12]/GPIO107
PCMADR[13]/GPIO110
GPIO_PM[3]/GPIO9
GPIO_PM[4]/GPIO10
K4 D1 AE15
NC_7 NC_24 NC_7 NC_24
AA17
PCMADR[14]/GPIO109 PM_UART_RX/GPIO_PM[5]/GPIO11
L6
C2
RGB_DDC_SCL DDCA_CK/UART0_RX TS1DATA_[1]/GPIO92 FE_TS_DATA[2]
10 39 10 39 Y20
PM_SPI_SCZ1/GPIO_PM[6]/GPIO12
L5
AE14
PCMREG_N/GPIO126 GPIO_PM[7]/GPIO13
M6 TS1DATA_[2]/GPIO93 FE_TS_DATA[3]
NC_8 NC_23 NC_8 NC_23 AB15
PCMOE_N/GPIO116
GPIO_PM[8]/GPIO14
GPIO_PM[9]/GPIO15
M5 AC13
11 38 11 38
AA22
AD22
PCMWE_N/GPIO195 PM_SPI_SCZ2/GPIO_PM[10]/GPIO16
C1
M4
TS1DATA_[3]/GPIO94 FE_TS_DATA[4]
AD20
PCMIORD_N/GPIO114 GPIO_PM[11]/GPIO17 P21 AC14
VCC_1 VCC_2 VDD_1 VDD_2
PCMIOWR_N/GPIO112
A2 PWM0 PWM0/GPIO69 TS1DATA_[4]/GPIO95 FE_TS_DATA[5]
12 37 12 37 AD21
PCMCE_N/GPIO118
PM_SPI_SCK/GPIO1
PM_SPI_CZ0/GPIO_PM[12]/GPIO0
D3 N23 AD12
AC20
Y18
PCMIRQA_N/GPIO108 PM_SPI_SDI/GPIO2
B2
B1
PWM1 PWM1/GPIO70 TS1DATA_[5]/GPIO96 FE_TS_DATA[6]
VSS_1 VSS_2 VSS_1 VSS_2 Y21
PCMCD_N/GPIO133 PM_SPI_SDO/GPIO3 P22 AD13
13 36 13 36 Y22
PCMWAIT_N/GPIO103
PWM2 PWM2/GPIO71 TS1DATA_[6]/GPIO97 FE_TS_DATA[7]
PCM_RESET/GPIO132
R110 22 R21 AD14
NC_9 NC_22 NC_9 NC_22 U21
TS0CLK/GPIO90
Y14
AA10
SCART1_MUTE PWM3/GPIO72 TS1DATA_[7]/GPIO98
14 35 14 35 V21
PCM2_CE_N/GPIO134 TS0VALID/GPIO88
Y12 R154 22 P20
R20
PCM2_IRQA_N/GPIO135 TS0SYNC/GPIO89
ERROR_OUT PWM4/GPIO73
NC_10 NC_21 NC_10 NC_21 T20
PCM2_CD_N/GPIO138
PCM2_WAIT_N/GPIO136 TS0DATA_[0]/GPIO80
Y13 R113 22 F6
15 34 15 34
U22
PCM2_RESET/GPIO137 TS0DATA_[1]/GPIO81
Y11
AA12
LED_AMBER PWM_PM/GPIO197
TS0DATA_[2]/GPIO82
D4 AB12
UART1_TX/GPIO46 TS0DATA_[3]/GPIO83
CLE NC_20 CL NC_20 N25
E4
UART1_RX/GPIO47 TS0DATA_[4]/GPIO84
AA14
AB14
16 33 16 33 N24
UART2_TX/GPIO68 TS0DATA_[5]/GPIO85
AA13
UART2_RX/GPIO67 TS0DATA_[6]/GPIO86
B8 AB11
ALE I/O3 AL I/O3 A8
UART3_TX/GPIO50 TS0DATA_[7]/GPIO87 H6
17 32 17 32
UART3_RX/GPIO51
AC15 KEY1 SAR0/GPIO34
P23
I2C_SCKM2/DDCR_CK/GPIO75
TS1CLK/GPIO101
TS1VALID/GPI99
AD15 G5
WE I/O2 W I/O2
P24
I2C_SDAM2/DDCR_DA/GPIO74 TS1SYNC/GPIO100
AC16
KEY2 SAR1/GPIO35
18 31 18 31 D2 AD16 C107 C110 G4
D1
DDCA_DA/UART0_TX TS1DATA_[0]/GPIO91
AE15 SAR2/GPIO36
WP I/O1 WP I/O1
DDCA_CK/UART0_RX TS1DATA_[1]/GPIO92
TS1DATA_[2]/GPIO93
AE14 2011.11.15 0.1uF 0.1uF J5
19 30 19 30 P21
TS1DATA_[3]/GPIO94
AC13
AC14 WalkieTalkie Issue 16V 16V SAR3/GPIO37
N23
PWM0/GPIO69 TS1DATA_[4]/GPIO95
AD12
J4
NC_11 I/O0 NC_11 I/O0 P22
PWM1/GPIO70
PWM2/GPIO71
TS1DATA_[5]/GPIO96
TS1DATA_[6]/GPIO97
AD13 SAR4/GPIO38
R21 AD14
20 29 20 29 P20
PWM3/GPIO72 TS1DATA_[7]/GPIO98
R101 22
PWM4/GPIO73
F6
NC_12 NC_19 NC_12 NC_19 PWM_PM/GPIO197 KEY_SCL
21 28 21 28 R163 22
H6
SAR0/GPIO34 KEY_SDA R23
NC_13 NC_18 NC_13 NC_18
G5
G4
SAR1/GPIO35
R164 22 VSYNC_LIKE/GPIO146
SAR2/GPIO36
22 27 22 27 J5
J4
SAR3/GPIO37 LED_RED
NC_14 NC_17 NC_14 NC_17
SAR4/GPIO38
R24
23 26 23 26 R23
SPI1_CK/GPIO199
VSYNC_LIKE/GPIO146 R25
NC_15 NC_16 NC_15 NC_16 R24 SPI1_DI/GPIO200
24 25 24 25 R25
SPI1_CK/GPIO199
SPI1_DI/GPIO200
T21
T21
T22
SPI2_CK/GPIO201 SPI2_CK/GPIO201
SPI2_DI/GPIO202 T22
SPI2_DI/GPIO202

+5V_Normal

IC101
DIMMING PM MODEL OPTION MSD804KKX
I2C +3.3V_Normal
+3.3V_ST
121019

R126
R130
ADDED to improve EMI

10K
S7LR-M_NON_MS10
WLED_ENABLE
R131 10K
100 C7 AB25 R182 22
OPT OPT C AMP_RST GPIO39 LVA0P RXA0+
R127 applied on only SMALL PCB E6 AB23 R183 22
R174 R177 121018 OLP GPIO40 LVA0N RXA0-
R156 10K 10K 10K Q100 B 4.7K F5 AC25 R184 22
BLU_CURRENT_CTL PWM0 Net Name Change RXA1+
R140 R141 R160 R161 R144 R145 MMBT3904(NXP) GPIO41 LVA1P
1K 1K 4.7K 4.7K 2.2K 2.2K R178 100 OPT B6 AB24 R185 22
R157 100 PC_AUDIO_DET GPIO42 LVA1N RXA1-
WLED_DIM_ADJ PWM2 BOOT_POWER_OPTION_0 E E5 AD25 R186 22
AV_CVBS_DET GPIO43 LVA2P RXA2+
R179 100 OPT 121018 D5 AC24 R187 22
C100 C111 MODEL_OPT_8 GPIO44 LVA2N RXA2-
4.7K ADDED B7 AE23 R188 22
1uF 2.2uF AMP_SDA BOOT_POWER_OPTION_1
R129 SCART1_DET GPIO45 LVA3P RXA3+
OPT AMP_SCL E7 AC23 R189 22
OPT OPT OPT HP_DET GPIO48 LVA3N RXA3-
R175 R176 F7 AC22
I2C_SDA 10K 10K 121018 MODEL_OPT_9 GPIO49 LVA4P
120915 AB5 AD23
I2C_SCL ADDED ADDED TUNER_RESET GPIO52 LVA4N
AB3
MODEL_OPT_0 GPIO53
KEY_SDA A9 V23
NAND_EN GPIO54 LVB0P
KEY_SCL F4 U24
MODEL_OPT_1 GPIO55 LVB0N
AB1 V25
R181
10K

I2C_SCKM0/GPIO56 LVB1P
N6 V24
I2C_SDAM0/GPIO57 LVB1N
AB2 W25
MODEL_OPT_2 GPIO76 LVB2P
+3.3V_ST +3.3V_ST AC2 W23
EEPROM SERIAL FLASH MEMORY DEMOD_RESET GPIO77 LVB2N
+3.3V_Normal AA23
LVB3P
S_FLASH_MAIN_WINBOND Y24
LVB3N
AA25
NVRAM_ST NVRAM_RENESAS OPT IC100 LVB4P
AA24
IC103-*1 IC103-*2 R138 LVB4N
IC103 +3.3V_ST 4.7K W25Q80BVSSIG
AT24C256C-SSHL-T C105 M24256-BRMN6TP R1EX24256BSAS0A
C114 AE24 R158 22
NVRAM_ATMEL 0.1uF S_FLASH_MAIN_MACRONIX LVACLKP RXACK+
CS VCC 0.1uF AD24 R159 22
E0 VCC A0 VCC 1 8 IC100-*1 LVACLKN RXACK-
1 8 1 8 /SPI_CS Y23
A0 VCC
OPT MX25L8006EM2I-12G LVBCLKP
1 8 R135 W24
E1 WC A1 WP
10K DO[IO1] HOLD[IO3] LVBCLKN
2 7 2 7 2 7
SPI_SDO
A1 WP T25
2 7 CS# VCC MODEL_OPT_3
E2 SCL A2 SCL 1 8 GPIO194
A0’h 3 6 3 6 %WP[IO2] CLK U23
3 6 GPIO191 MODEL_OPT_4
A2 SCL /FLASH_WP SPI_SCK T24
3 6 R111 22 I2C_SCL VSS SDA VSS SDA SO/SIO1 HOLD# GPIO192 MODEL_OPT_5
4 5 4 5 R139 2 7 T23
GND SDA GND DI[IO0] 33 GPIO193
4 5 R112 22 4 5
I2C_SDA SPI_SDI
C104 C106 WP# SCLK
EAN61548301 EAN62389501 3 6
8pF 8pF
EAN61133501 OPT OPT
GND SI/SIO0
4 5

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES EAX65077403

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC4_S7LRM 2012.11.18
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MAIN1_EU 1 12

Copyright ⓒ 2013 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 PIN NAME PIN NO. LOW HIGH
MODEL OPTION MODEL_OPT_0 MEMORY OPTION
AB3 FHD HD
+3.3V_ST +3.3V_Normal +2.5V_Normal +3.3V_Normal
MODEL_OPT_DUAL_STREAM(O)

MODEL_OPT_1 Memory Model Model Note +1.15V_VDDC

F4 PHM_OFF PHM_ON VDDC 1.15V
MODEL_OPT_MIU0-256M

MODEL_OPT_DVB_T2(O)

+1.15V_VDDC
MODEL_OPT_DVB_S(O)

OPT 4 OPT 6
MODEL_OPT_MIU1(O)

MODEL_OPT_M120(O)

MODEL_OPT_PHM(O)
10K

10K

MODEL_OPT_2 AB2 VDDC : 2026mA

MODEL_OPT_HD
NON_DVB_T2 DVB_T2

(OPT)ZENER MainIC
1K

1K

1K

1K

1K

1K

1K

1K
(OPT)TAIWAN

128M 0 0
MODEL_OPT_3 T25 NON_M120 M120

0.1uF

0.1uF

0.1uF

0.1uF

0.1uF

0.1uF

0.1uF

0.1uF
10uF

10uF
10uF
OPT

1uF

1uF
128M+128M 0 1 OPT OPT
MODEL_OPT_4 U23 MIU0-128M MIU0-256M
ZD201
R300

R301

R290

R291

R222

R224

R206

R208

R211

R226

5.6B

C275

C276
C228
OPT OPT OPT OPT OPT
MODEL_OPT_5 256M 1 0 OPT

C283
C277

C280

C292

C299

C260

C291

C298

C302

C304
T24 NON_DVB_S DVB_S
MODEL_OPT_0
MODEL_OPT_1 MODEL_OPT_6 B8 MIU1-NO_DDR MIU1-128M 1 1 Ginga
R203 100 256M+128M 111128
RF_SWITCH_CTL
(OPT)RF_SW_OPT MODEL_OPT_2 Dual Stream is only Korea 3D spec Zener Add
MODEL_OPT_3 MODEL_OPT_7 A8 NON_DualStream DualStream
MODEL_OPT_4
MODEL_OPT_8 F7 HD_LVDS_EU HD_LVDS_NON_EU
MODEL_OPT_5
MODEL_OPT_6 MODEL_OPT_9 A9 EU,AJ TAIWAN
MODEL_OPT_7 Other: N.C Normal Power 3.3V IC101
MSD804KKX
MODEL_OPT_8 +3.3V_Normal VDD33 +1.15V_VDDC
MODEL_OPT_DUAL_STREAM(X)

MODEL_OPT_9
S7LR-M_NON_MS10
MODEL_OPT_MIU0-128M

MODEL_OPT_DVB_T2(X)
MODEL_OPT_DVB_S(X)

Close to MSTAR DTV_IF

MODEL_OPT_MIU1(X)

MODEL_OPT_M120(X)

MODEL_OPT_PHM(X)

OPT

OPT

OPT

OPT

OPT
R268

0.1uF OPT
R288 100 C257 0.1uF K12 G10
MODEL_OPT_FHD
10K

10K

IF_P_MSTAR 0
1K

1K

1K

1K

1K

1K

1K

1K

AVDDLV_USB GND_32
G11

(OPT)ZENER MainIC

0.1uF

0.1uF

0.1uF

0.1uF

0.1uF

0.1uF

0.1uF

0.1uF
GND_33

0.1uF
C287 1/10W

0.1uF
100pF C288 G9 G12

10uF
10uF

C254 10uF
33pF 5%

OPT
OPT VDDC_1 GND_34
H9 G13
R289 100 C258 0.1uF VDDC_2 GND_35
IF_N_MSTAR K10 G14
R294

R223

R225

R207

R209

R212

R227

ZD202
R302

R303

R293

VDDC_3 GND_36

C293
C284

C255

C259

C266

C279

C297

C301

C265

C267

C232
5.6B K11 G17

C239

C246
C289 VDDC_4 GND_37
33pF L10 G18
IC101 M12
VDDC_5 GND_38
G19
MSD804KKX M13
VDDC_6 GND_39
G24
111128 VDDC_7 GND_40
C250 0.1uF R234 47 TU_SIF N12 H11
Zener Add VDDC_8 GND_41
S7LR-M_NON_MS10 C251 0.1uF R235 47 AVDD_AU33 P14 H12
C264 VDDC_9 GND_42
J2 AC4 1000pF P15 H13
RXACKP NC_8 VDDC_10 GND_43
J3 AD3 ANALOG SIF OPT
50V R269 R10 H14
RXACKN NC_9 VDDC_11 GND_44
K3 Close to MSTAR 0 FB_CORE R14 H15
RXA0P VDDC_12 GND_45
J1 AC3 1/10W R15 H16
RXA0N IP C240 C241 VDDC_13 GND_46
K2 AE3 +3.3V_Normal 5% 0.1uF T10 H17
0.1uF
RXA1P IM VDDC_14 GND_47
K1 H18
RXA1N GND_48
L2 AD4 R274 H19
RXA2P SIFP 0 GND_49
L3 AC5 P10 J9
RXA2N SIFM NC_2 GND_50
T5 P19 J10
DDCDA_DA/GPIO27 FB_CORE FB_CORE GND_51
T4 C282 R16 J11
0.1uF R243
DDCDA_CK/GPIO26 10K AVDDL_MOD GND_52
V5 L11 J12
BOOT_POWER_OPTION_0 HOTPLUGA/GPIO22 NC_1 GND_53
R247 M14 J13
121018 0 MIUVDDC DVDD_DDR GND_54
PM_MODEL_OPT_0 AD2 J14
IF_AGC IF_AGC_MAIN GND_55
->BOOT_POWER_OPTION_0
RF_AGC
AE2
C285
STby 3.3V GND_56
J15

0.047uF W9 J16
AVDD2P5 AVDD2P5_ADC_1 GND_57
25V AVDD_NODIE:7.362mA W10 J18
TUNER_I2C AVDD2P5_ADC_2 GND_58
AE6 W11 J19
I2C_SCKM1/GPIO78 TU_SCL AVDD2P5_ADC_3 GND_59
AD6 +3.3V_ST AVDD_NODIE W12 J25
I2C_SDAM1/GPIO79 TU_SDA AVDD2P5_ADC_4 GND_60
Close to MSTAR R216 K9
GND_61
0 Y17 K13
121018 C261 27pF AVDD25_LAN GND_62
PM_MODEL_OPT_1 AD1 1/10W C286 K14
XIN C252 GND_63
->BOOT_POWER_OPTION_1 AC1 5% 0.1uF 0.1uF V18 H10
R287

X201 AVDD2P5_MOD
XOUT AVDD_MOD_1 GND_64
1M

(OPT)ZENER MainIC
BOOT_POWER_OPTION_1 R5 24MHz C262 27pF 12.08.03 U19 K18
HOTPLUGD/GPIO25 AVDD_MOD_2 GND_65
HDMI

22->27pF K19
GND_66
AE9 D7 OPT R297 0 K22
CK+_HDMI2 RXCCKP SPDIF_IN/GPIO150 CI_DET GND_67
AC9 D6 ZD203 AVDD_MPLL W14 L8
CK-_HDMI2 RXCCKN SPDIF_OUT/GPIO151 5.6B NC_3 GND_68
AC10 OPT R296 100 W15 L9
D0+_HDMI2 RXC0P NC_4 GND_69
AD9 R217 J8
D0-_HDMI2 RXC0N 111128 GND_70
AC11 E3 SIDE USB Zener Add
0 U7 L12
D1+_HDMI2 RXC1P USB0_DM AVDD_NODIE AVDD_NODIE GND_71
AD10 E2 1/10W L13
D1-_HDMI2 RXC1N USB0_DP GND_72
AE11 5% C234 L7 L18
D2+_HDMI2 RXC2P 0.1uF AVDD_DVI AVDD_DVI_USB_1 GND_73
AD11 AC12 M7 L19
D2-_HDMI2 RXC2N USB1_DM USB_DM AVDD_DVI_USB_2 GND_74
120715 R218 22 AE8 AE12 AVDD_MPLL P7 M8
DDC_SDA_2 DDCDC_DA/GPIO31 USB1_DP USB_DP AVDD3P3_MPLL GND_75
Added R219 22 AD8 AVDD_DVI R7 K8
DDC_SCL_2 DDCDC_CK/GPIO30 AVDD_DMPLL GND_76
AC8 M10
HPD2 HOTPLUGC/GPIO24 GND_77
C8 R213 22 C307 1uF M19 M11
I2S_IN_BCK/GPIO148 AMP_SCL R215 DVDD_NODIE GND_78

0.1uF

0.1uF
F2 D8 R214 22 0 L14

C202 10uF
CK+_HDMI1 RXBCKP I2S_IN_SD/GPIO149 AMP_SDA GND_79
F3 D9 V7 M15
CK-_HDMI1 RXBCKN I2S_IN_WS/GPIO147 COMP_DET 1/10W AVDD_AU33 AVDD_AU33 GND_80
G3 5% W7 M16
D0+_HDMI1 RXB0P AVDD_EAR33 GND_81
F1 B10 M18

C229

C235
D0-_HDMI1 RXB0N I2S_OUT_BCK/GPIO154 AUD_SCK GND_82
G2 C9 R19 M25
D1+_HDMI1 RXB1P I2S_OUT_MCK/GPIO152 AUD_MASTER_CLK_0 VDD33 VDDP_1 GND_83
G1 B9 T19 N10
D1-_HDMI1 RXB1N I2S_OUT_SD/GPIO155 AUD_LRCH VDDP_2 GND_84
H2 N11
D2+_HDMI1 RXB2P GND_85
H3 W18 N13
D2-_HDMI1 RXB2N I2S_I/F AVDD_LPLL_1 GND_86
120715 R220 22 R6 W19 N14
DDC_SDA_1 DDCDB_DA/GPIO29 AVDD_LPLL_2 GND_87
Added R221 22 U6 C10 N15
DDC_SCL_1 DDCDB_CK/GPIO28 I2S_OUT_WS/GPIO153 AUD_LRCK GND_88
P5 V19 N16
HPD1 HOTPLUGB/GPIO23 VDD33 VDDP_NAND GND_89
R4 N17
CEC_REMOTE_S7 CEC/GPIO5 GND_90
AB9 C236 2.2uF N19
AUL0
AUR0
AA11 C237 2.2uF
SC1_L_IN
SC1_R_IN
DDR3 1.5V AVDD_MIU
J17
AVDD_DDR0_D_1
GND_91
GND_92
K7
R266 510 P2 Y9 K15 P8
DSUB_HSYNC HSYNC0 AUL1 AVDD_DDR0_D_2 GND_93
R267 510 R3 AA9 K16 P9
DSUB_VSYNC VSYNC0 AUR1 AVDD_DDR0_D_3 GND_94
R228 33 C204 0.047uF N2 AA7 L15 M9
DSUB_R+ RIN0P AUL2 AVDD_DDR0_C GND_95
DSUB

R229 68 C205 0.047uF P3 AB8 P11

RIN0M AUR2 AVDD_DDR0:55mA GND_96
R230 33 C206 0.047uF N3 Y8 C242 2.2uF +1.5V_DDR K17 P13
DSUB_G+ GIN0P AUL3 COMP_L_IN AVDD_MIU AVDD_DDR1_D_1 GND_97
R231 68 C207 0.047uF N1 Y10 C243 2.2uF L17 P16
GIN0M AUR3 COMP_R_IN AVDD_DDR1_D_2 GND_98
R232 33 C208 0.047uF M3 AC7 C244 2.2uF M17 P17
DSUB_B+ BIN0P AUL4 PC_L_IN R270 AVDD_DDR1_D_3 GND_99
R233 68 C209 0.047uF M2 AD7 C245 2.2uF 0 L16 P18
BIN0M AUR4 PC_R_IN AVDD_DDR1_C GND_100
2.4K

M1

0.1uFOPT
C210 1000pF P12
10K

SOGIN0 1/10W GND_101

10uF OPT

0.1uF OPT
R260

R261

AUDIO IN 5% R8

0.1uF

0.1uF
SCART1_RGB

C278

10uF
C281

C290

C296

C300

C303

C305
GND_102

0.1uF

1uF
E9 R9
C306
GND_EFUSE GND_103
V2 R11
SC1_ID HSYNC1 GND_104
V3 W6 AUDIO OUT R12
SC1_FB VSYNC1 GPIO_PM[13]/GPIO19 MHL_CD_SENSE GND_105
R253 33 C211 0.047uF U3 V6 A23 R13
SC1_R+ RIN1P AUOUTL2 SCART1_Lout GND_1 GND_106
R254 68 C212 0.047uF U2 V4 B17 R17
RIN1M AVDD5V_MHL AVDD5V_MHL AVDD_DDR1:55mA GND_2 GND_107
R255 33 C213 0.047uF T1 Y7 C23 T8
SC1_G+ GIN1P GPIO_PM[14]/GPIO20 /VBUS_EN GND_3 GND_108
R256 68 C214 0.047uF T2 W5 A5 T9
GIN1M AUOUTR2 SCART1_Rout GND_4 GND_109
R257 33 C215 0.047uF R2 U5 C11 N7
SC1_B+ BIN1P GPIO_PM[15]/GPIO21 TP209 GND_5 GND_110
R258 68 C216 0.047uF R1 C19 T11
BIN1M GND_6 GND_111
C217 1000pF T3 C22 T12
SC1_SOG_IN SOGIN1 GND_7 GND_112
R236 0 D14 T13
GND_8 GND_113
OPT D18 T14
+1.15V_VDDC GND_9 GND_114
AA2 D19 T15
COMP
R237 33 C218 0.047uF Y2
HSYNC2 MIUVDDC Normal 2.5V E17
GND_10 GND_115
T16
COMP_Pr+ RIN2P L202 GND_11 GND_116
R238 68 C219 0.047uF AA3
BLM18SG121TN1D R271 E18 T17
RIN2M 0 +2.5V_Normal AVDD2P5 GND_12 GND_117
R239 33 C220 0.047uF W2 AD5 E19 U8
COMP_Y+/AV_CVBS_IN GIN2P AUVRM GND_13 GND_118
R240 68 C221 0.047uF Y3 C249 C253 C256 C263 1/10W E22 U9
GIN2M 4.7uF 1uF 0.1uF 10uF C247 C248 R272 AVDD2P5:172mA GND_14 GND_119
R241 33 C222 0.047uF V1 AE5 5% 10uF 0.1uF F8 U10
COMP_Pb+ BIN2P AUVAG 0 GND_15 GND_120
R242 68 C223 0.047uF W3 AC6 F17 U11

(OPT)ZENER MainIC
BIN2M AUVRP 1/10W GND_16 GND_121
C224 1000pF W1 OPT OPT F18 U12
SOGIN2 H/P OUT 5% GND_17 GND_122
AA6 L203 5.6uH LN4500 C269 C270 C271 C273 C274 F19 U13
EARPHONE_OUTL HP_LOUT 10uF 0.1uF 0.1uF 0.1uF 0.1uF GND_18 GND_123
CVBS In/OUT OPT OPT AB6 L205 5.6uH LN4500 G8 U14
EARPHONE_OUTR HP_ROUT ZD204 GND_19 GND_124
R244 33 C225 0.047uF AA8 5.6B H8 U15
TU_CVBS CVBS0 GND_20 GND_125
R245 33 C226 0.047uF Y4 N22 U16
SC1_CVBS_IN CVBS1 R275 111128 GND_21 GND_126
R246 33 C227 0.047uF W4 C6 0 R276 Zener Add AVDD2P5_MOD N21 U17
COMP_Y+/AV_CVBS_IN CVBS2 RP/GPIO63 LN4500 0 GND_22 GND_127
OPT OPT AA5 C5 LN4500 AVDD25_PGA:13mA N20 R18
Y5
CVBS3 TP/GPIO60 SOC_RESET M22
GND_23 GND_128
V9
C268 C272 R273
NC_5 0 GND_24 GND_129
AA4 A6 4.7uF R277 4.7uF R278 +3.3V_ST M21 V10
NC_7 RN/GPIO66 10V 0 10V 0 GND_25 GND_130
Y6 C4 OPT OPT 1/10W M20 V11
NC_6 LED1/GPIO59 LN4500 LN4500 GND_26 GND_131
DTV/MNT_VOUT AA1 5% C238 F10 V12
CVBSOUT1 0.1uF GND_27 GND_132
B5 V15 V14
C203 TN/GPIO62 16V GND_28 GND_133
1000pF R252 68 C233 0.047uF AB4 C3 111026Switch W16 V17
50V VCOM GPIO61 EBF32593901 Deletion GND_29 GND_134
OPT A3 V8 T7
GPIO64 C200 GND_30 GND_135
Close to MSTAR GPIO65
B3
4.7uF
T18
GND_31 GND_136
E8
B4 10V
LED0/GPIO58 R205
10
SOC_RESET
C
N4 D200 OPT OPT
IRIN/GPIO4 IR MMBD6100 C201 ZD200
T6 R210 0 C231 1uF R200
ARC0 HDMI_ARC A2 A1 62K 0.1uF 3.3V
N5 OPT OPT
HWRESET SOC_RESET

SB_MUTE

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES EAX65077403

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC4_S7LRM 2012.11.18
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MAIN2_EU 2 12

Copyright ⓒ 2013 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 +3.3V_ST
DSUB RGB D416
+5V_Normal
PC AUDIO(SIDE) USB(SIDE)
MMBD6100

R420

R421
A2

0
OPT

0
C IC400
AP2191DSG
A1 +5V_USB
NC GND
+3.3V_Normal 8 1

OUT_2 IN_1
7 2

OUT_1 IN_2
6 3
12.08.10 R407
470K C400 C404 C405
R408 R413 47K->470K R409 0.1uF 10uF
FLG
5 4
EN

10K 10K 1K 10V USB_CTL 0.1uF

PC_AUDIO_DET OPT R417
RGB_DDC_SCL 10K
JP411 VA407
RGB_DDC_SDA 20V
OPT R419
47
OPT OPT R444
OPT 15K 3AU04S-305-ZC-(LG)
C401 C403 VA415 PC_R_IN
R405 JK402 USB_OCD
18pF 18pF 0 6 M6
50V 50V 20V
PM_RXD C414 R442
OPT JP404 VA419 R446

1
20V 220pF 470K 10K

OPT
1 M1

USB DOWN STREAM

OPT 50V
R406
0 JP429
3 M3_DETECT

2
OPT OPT PM_TXD R445 USB_DM 1:AL8
VA400 VA401 15K
20V 20V PC_L_IN
OPT OPT 12.07.02 4 M4 JP428
R403 R404

3
BY.Hwang USB_DP 1:AL7
0 0 JP403 R441
VA420 C413 470K
5 M5_GND R447

OPT
VA417 +3.3V_ST 20V 220pF 10K OPT OPT
2:E18 DSUB_VSYNC JP400 JP427 111026

4
20V KJA-PH-1-0177 50V VA424 VA425
OPT JK401 20V 20V ESD diode deletion
JP402

5
2:E18 DSUB_HSYNC JP401 EAH39491601 2EA

R418
47K
JP408 120103
L401 JP409 R434 ESD diode addition
BLM15BD121SN1 47K EAF61530301 2EA
DSUB_DET
DSUB_B+ C
R429 0 JP407 Q400
R400 R435 B
C419 75 R427 0 MMBT3904(NXP)
47pF 10K
50V L402 R426 0 R431 VA418
BLM15BD121SN1 JP405 0 20V E
DSUB_G+ OPT
OPT
C420 R401
GREEN_GND

DDC_CLOCK
DDC_DATA

BLUE_GND

SYNC_GND

47pF 75
RED_GND

DDC_GND

L403
H_SYNC

V_SYNC
GND_2

GREEN

GND_1

50V JP406
BLUE

BLM15BD121SN1
RED

NC

JP410

DSUB_R+
SHILED

C421
11

12

13

14

15

R402
47pF
50V 75 Jack Shield (HDMI1, HDMI2, RGB)
16
10
6

11.10.31
To Improve EMI
1

5
5.5V

5.5V
VA402

VA403

VA406
5.5V

JK400
SPG09-DB-010

JackShield(for NonCKD) JackShield(for CKD)

11.10.27 M1 M1-*1
To Improve Ringing issue MGJ63348201
LOW capacitance Part apply MGJ63348202

RS232C(SIDE) Hotel_Model(RS232C apply)

C402 +3.3V_ST
0.33uF
16V
Hotel_Model(RS232C apply)

Hotel_Model(RS232C apply) C407

0.33uF 120918
C406 16V
0.33uF JIG GND Point addition
16V C408
0.1uF
16V
Hotel_Model(RS232C apply)
DOUT2
RIN2

C2-

C2+

C1-

C1+
V-

V+

JP_GND1 JP_GND2 JP_GND3 JP_GND4

8

IC401

MAX3232CDR

Hotel_Model(RS232C apply)
10

11

12

13

14

15

16
9
ROUT2

DIN2

DIN1

ROUT1

RIN1

DOUT1

GND

VCC

Hotel_Model(RS232C apply)
R410
0 C409
0.1uF
NON_Hotel_Model(RS232C Bypass) 16V +3.3V_ST
PM_TXD R412
0 P400
R415
PM_RXD 100 VA411
NON_Hotel_Model(RS232C Bypass) 20V 12507WS-04L
R414
100
VA408 VA410 1
20V 20V
OPT OPT VA412
20V 2

JP413 JP414
JP412 4
(OPT)IR_OUT
IR_OUT 5
M3_DETECT

R416
0
M5_GND

M4

M1

M6
5

6
KJA-PH-1-0177
JK404

Hotel_Model(RS232C apply)

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES EAX65077403

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC4_S7LRM 2012.11.18
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. INTERFACE 4 12

Copyright ⓒ 2013 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 HDMI
HDMI_1
+3.3V_ST CEC
R520
100
R506
47K

HDMI_CEC CEC_REMOTE_S7
R504

OPT
47K
OPT

OPT 5V_DET_HDMI_1
C
R505 Q500
10K B MMBT3904(NXP)

E OPT
OPT
5V_HDMI_1 VA504 5V_HDMI_1 +5V_Normal 5V_HDMI_2 +5V_Normal
OPT +3.3V_ST

R508

A1

A2

A1

A2

A1

A2
SHIELD 10K
OPT MMBD6100 MMBD6100 MMBD6100
R502 D501 D502 D503
20 OPT

C
C
1K OPT R510
Q502 B 10K
19 OPT HPD1
OPT VA512 MMBT3904(NXP)
18 20V
VA511 E 121118
R517 R518
17 20V R521 R522 47K->2.7K
2.7K 2.7K 2.7K 2.7K
16 DDC_SDA_1

DDC_SCL_1 DDC_SDA_1 DDC_SDA_2

15
R526 0
HDMI_ARC OPT OPT
14 (OPT)HDMI1_ARC VA500 VA501 DDC_SCL_1 DDC_SCL_2
HDMI_CEC
20V 20V
13
EAG61491201

OPT OPT
VA507 VA508
12 20V 20V
(OPT)ESD_HDMI_SEMTECH(DEV)
OPT

11 D504 120715
CK+ RCLAMP0524PA Added for ESD prevention
10 1 10 120825
D0- 2 9 CK-_HDMI1 OPT->APPLY
9
CK+_HDMI1
D0_GND 3 8
8 4 7
D0+ D0-_HDMI1
7 5 6
D0+_HDMI1
D1- 120825
6 ESD component addition
D1_GND (OPT)ESD_HDMI_SEMTECH(DEV)
5 D504-*1 D505-*1
D505 IP4283CZ10-TBA IP4283CZ10-TBA
D1+
4
D2-
1
2
RCLAMP0524PA
10
9
D1-_HDMI1
TMDS_CH1-
1 10
NC_4 TMDS_CH1-
1 10
NC_4 MHL OCP
3 D1+_HDMI1 TMDS_CH1+ NC_3 TMDS_CH1+ NC_3
2 9 2 9
D2_GND 3 8
2 4 7
GND_1
3 8
GND_2 GND_1
3 8
GND_2

D2+ D2-_HDMI1
1 5 6 TMDS_CH2-
4 7
NC_2 TMDS_CH2-
4 7
NC_2
D2+_HDMI1
TMDS_CH2+ NC_1 TMDS_CH2+ NC_1
5 6 5 6

LN4500
AVDD5V_MHL 5V_HDMI_2
(OPT)ESD_HDMI_NXP (OPT)ESD_HDMI_NXP IC500
JK500 +5V_ST
BD82020FVJ +5V_USB +3.3V_Normal
R531 LN4500
0
D500
MBR230LSFT1G OUT_3 GND MHL 5V from USB
8 1 R539 +3.3V_Normal
R511 30V 0
10 C500 100K OUT_2 IN_1
10uF OPT 7 2
10V R516 R538
HDMI_2 With MHL 121109
Change 0ohm -> 10ohm
LN4500
(EOS Issue..Mstar Recommand)
OUT_1
6 3
IN_2
C503
0.1uF
LN4500
R519
10K
R535
2.7K
10K
(OPT)LN4500MHL_OLD
LN4500 LN4500
0
OC EN

E
+3.3V_ST 5 4 R537
+3.3V_Normal 0
R536 Q506 (OPT)LN4500MHL_OLD
LN4500 LN4500 C
R523

B
B 10K
R515 R533
/VBUS_EN
10K 20K LN4500
R503

/MHL_OCP_DET LN4500 (Active Low)

LN4500 LN4500 R534 Q508
47K

E
10K LN4500
R500
47K

R525 0 LN4500
5V_DET_HDMI_2 C
C R524
R501 Q501 B 10K
10K B MMBT3904(NXP) MHL_OCP_EN
LN4500
Q507 (Active High)
E
OPT E LN4500
5V_HDMI_2 VA505

LN4500 121118
22->100ohm
R509
100
MN33D
SHIELD
R528
MN33D
20 1K C
MN33D R529
Q505 B 10K
19 MMBT3904(NXP) HPD2
OPT
VA514
18 OPT E
20V
VA513
17 20V
DDC_SDA_2
16
DDC_SCL_2
15
R527 0
HDMI_ARC
14 (OPT)HDMI2_ARC VA502 VA503
HDMI_CEC 20V 20V
13
EAG61491201

OPT OPT
VA509 VA510
12 20V 20V (OPT)ESD_HDMI_SEMTECH(DEV) 120715
D506
RCLAMP0524PA Added for ESD prevention
11 120825
CK+ 1 10
10 CK-_HDMI2 OPT->APPLY
2 9
D0- CK+_HDMI2 D506-*1 D507-*1
9 3 8 IP4283CZ10-TBA IP4283CZ10-TBA

D0_GND 4 7 TMDS_CH1- NC_4 TMDS_CH1- NC_4

8 D0-_HDMI2 1 10 1 10
5 6
D0+ D0+_HDMI2 TMDS_CH1+
2 9
NC_3 TMDS_CH1+
2 9
NC_3
7 120825
GND_1 GND_2 GND_1 GND_2
D1- ESD component addition 3 8 3 8
6
(OPT)ESD_HDMI_SEMTECH(DEV) TMDS_CH2-
4 7
NC_2 TMDS_CH2-
4 7
NC_2
D1_GND D507
5 TMDS_CH2+ NC_1 TMDS_CH2+ NC_1
RCLAMP0524PA 5 6 5 6
D1+ 1 10 ESD_HDMI_NXP ESD_HDMI_NXP
4 D1-_HDMI2
2 9
D2- D1+_HDMI2
3 3 8 +3.3V_ST
D2_GND 4 7
2 D2-_HDMI2
5 6
D2+ D2+_HDMI2
1
R513
10K
OPT

LN4500 E
R514
R512 10K Q504
0
JK501 MMBT3906(NXP)
OPT B
0 1/16W LN4500 C OPT
R530
C
VA506

MN33D 5% C502
B
5.6V

0.047uF Q503
OPT

25V MHL_CD_SENSE
MMBT3904(NXP)
E OPT
R507
R532 121118
0 300K LN4500->APPLY
LN4500

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES EAX65077403

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC4_S7LRM 2012.11.18
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. HDMI 5 12

Copyright ⓒ 2013 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 IR/LED and Control Module
+3.3V_ST
P600 P601
12507WR-12L 10031HR-30

KEY2 R616 L600

3.3K BLM18PG121SN1D JP600
KEY1 1 1
KEY_SCL R617
R614 3.3K 2
KEY_SDA 100 JP601
2
+3.3V_ST 3
+3.3V_ST R615
100 4
JP602 3
R604 270 R610 330
5
1/10W 1/10W
1% JP605
1% 4 6
RXA3+

RXA3- 7
Amber LED(Non M73):5.9mA JP604 5
Red LED(Non M73):4.8mA
8

JP603 6 RXACK+ 9
121118
R604,R610 RXACK- 10
2012->1608
7 11

JP607 RXA2+ 12
8
RXA2- 13
JP606
9 14

RXA1+ 15
JP608
R600 C 10
RXA1- 16
10K (IR Port protection against ESD) JP609
B Q600 R630
LED_RED 121018 17
MMBT3904(NXP) 100ohm->200ohm 200
IR 11
R601 E RXA0+ 18
10K
+3.3V_ST JP610
12 RXA0- 19
50V

100pF 50V PIN22 20

100pF 50V
20V
50V

JP611 13 0~0.7V VESA

OPT D603 20V

OPT D602 20V
1000pF
20V

C602

21
OPT

C603
C601

OPT
R628
2.7~3.3V JEDIA
0.1uF

0
C600

D601

22
D600

PIN23 23
LGD R629
GND 0 24
NC CMI 21.6"/26"
25
12.07.17
Change D601~3
26
R602 C
27
10K B Q601
LED_AMBER 28
MMBT3904(NXP) +12V_PANEL_POWER
R603 E
10K 2012.04.13 29
1K/10W -> 4.7K/10W
30

111116 31

4.7K
4.7K

4.7K
C605 C607

4.7K
100uF Ecap C606

R625
R624

R626

R627
Deletion 0.1uF 10uF 1000pF
EAE38362801 50V 25V 50V

2012.04.13
10uF/10V -> 10uF/25V
JP612

IR_OUT(Ready)

+3.3V_ST

(OPT)IR_OUT
R619
10K
OPT +3.3V_ST
R618 R620
22 0
IR_OUT
(OPT)IR_OUT
C (OPT)IR_OUT R622
R621 10K
Q602 B 10K
MMBT3904(NXP) (OPT)IR_OUT
(OPT)IR_OUT
E
C604
1000pF C
(OPT)IR_OUT R623
Q603 B 47K
MMBT3904(NXP) IR
(OPT)IR_OUT
(OPT)IR_OUT
E

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES

EAX65077403
SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC4_S7LRM 2012.11.18
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. MODULE&CONTROL 6 12

Copyright ⓒ 2013 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 L700-*1
10.0uH
(OPT)Audio_Coil_TAIYO
AUDIO AMP NRS6045T100MMGK

+3.3V_AMP L706-*1
AMP_RST 10.0uH (OPT)Audio_Coil_TAIYO
C706 NRS6045T100MMGK
1000pF
50V

50V
L701-*1
R716 10.0uH

22000pF
0 (OPT)Audio_Coil_TAIYO
+19V_AMP_VCC

C711
OPT NRS6045T100MMGK
AUD_MASTER_CLK R700
3.3
L709-*1
OPT 10.0uH (OPT)Audio_Coil_TAIYO
C712 C715 C718 C703
0.01uF NRS6045T100MMGK
0.1uF 0.1uF 10uF
C702 50V
50V 50V 25V

[EP]GND
C707 10uF

VDD_IO
GND_IO

PGND1A

PVDD1A
PVDD1B
10V
0.1uF

CLK_I

RESET
BST1A

OUT1A
16V D706
1N4148W R719 R715 L700
OPT 100V 12 12 R727
10uH Audio_Coil_ABCO C739
C701 OPT 0.1uF

AD
C700 C730 50V 5.1K
0.1uF 0.1uF LPH6045T-100M
390pF
16V 16V 50V C735
L706 0.47uF
10uHAudio_Coil_ABCO 50V
C731
390pF C740
40
39
38
37
36
35
34
33
32
31
50V LPH6045T-100M 0.1uF R728
D707 50V
1N4148W R720 R704 5.1K
AGND_PLL 1 30 OUT1B 100V
OPT
12 12

VDD_PLL 2 29 PGND1B C722

THERMAL 22000pF
P700
DGND_PLL 3 41 28 BST1B 50V
SMAW250-H04R

12.08.09 GND 4 27 VDR1

4 SPK_L+
DGND 5 IC700 26 VCC5
OPT
JP704
C704
0.1uF
16V
C725
1uF
10V
DVDD 6 NTP7513 25 AGND 3 SPK_L-

JP705
AUD_LRCH
SDATA 7 24 VDR2 2 SPK_R+

WCK
0x54 BST2A
C727
1uF
C743
1uF
C726
1uF
AUD_LRCK 8 23 25V 25V 25V
JP706
1 SPK_R-

AUD_SCK
BCK 9 22 PGND2A C723 JP707
22000pF
SDA 10 21 OUT2A 50V
WAFER-ANGLE
11
12
13
14
15
16
17
18
19
20
SCL
FAULT
MONITOR_0
MONITOR_1
MONITOR_2
BST2B
PGND2B
OUT2B
PVDD2B
PVDD2A

R703 100
AMP_SDA
R707 100 +19V_AMP_VCC D704
AMP_SCL R717 R712
1N4148W 12 12 L701
C705 C708 10uH Audio_Coil_ABCO
33pF 33pF 100V C737 R729
50V 50V OPT
TP700 C728 LPH6045T-100M 0.1uF 5.1K
390pF C734 50V
TP701 50V 0.47uF
L709 50V
C713 C714 C716 10uH Audio_Coil_ABCO
TP702 0.1uF 0.1uF 10uF C729
390pF LPH6045T-100M
50V 50V 25V D705 50V C738 R730
C710 1N4148W R718 R702 0.1uF 5.1K
22000pF 100V 12 12 50V
OPT
50V

+3.3V_ST

R705
10K
D700 R709 100
MMBD6100 C
A2
SB_MUTE R701 B Q700
C
MMBT3904(NXP) C709
A1 10K 1000pF
NTP_MUTE OPT
E 50V
R708
33K

Headphone block
+3.3V_Normal
121118
OPTION added for LN4500
LN4500
R706
47K LN4500
R710
1K
HP_DET

HP_LOUT
VA703
Pop-up noise killer
20V LN4500
OPT LN4500 C719 C720
LN4500 R713 1000pF 10uF
1K 10V
Q701 C 50V +19V
E LN4500 OPT
MMBT3904(NXP)
B Q705
MMBT3904(NXP)
B
C E

AC KDS226
D710

R734
6 M6 HP_ROUT A C R736
JP700 220K
11.10.27 470
1 M1 JP702 LN4500 2.7K->220K
C721 C724
LN4500
10uF E 47uF
3 M3_DETECT R711 C717 25V
LN4500 C 10V
JP703 E LN4500 1000pF
Q703 1K MMBT3906(NXP)
B Q704 50V
4 M4 VA701 MMBT3904(NXP) OPT B Q702
MMBT3904(NXP)
JP701 20V B 121118
C
VA702 E OPT R737 3K for SCART MUTE DEL
5 M5_GND LN4500 20V C C742 R737
+3.3V_ST R735 3K:
LN4500 4.7uF 12K
KJA-PH-1-0177-2 220K With SCART MUTE BLOCK
50V
JK700
LN4500 SB_MUTE 12K:
LN4500 LN4500 11.10.27 Without SCART MUTE BLOCK
Q706 Apply->OPT R738
R739 MMBT3906(NXP) 12K
0
C

MUTE control
1/16W
5% LN4500
D709
B

MMBD6100
C LN4500 A2
12.08.16 12.11.07 R714 SB_MUTE
B R733 C
Added by JCPark 1K->0 by JHShin 3.3K
to solve pop-noise issue 10K A1
Q707 HP_MUTE
E
MMBT3904(NXP)
LN4500

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES EAX65077403

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC4_S7LRM 2012.11.18
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. AUDIO AMP 7 12

Copyright ⓒ 2013 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 R801
100K 11.10.27
111116 +3.3V_AMP
EBK61011501(Diode) PANEL POWER CONTROL
R803 C818 ->EBK38029201(Rohm)
+3.3V_ST ->EBK61913601(NXP) 3.3V drive
0.1uF
36K +12V_Normal
50V C807 +12V_PANEL_POWER
0.1uF +3.3V_ST
16V IC809
[EP]GND MP1584EN

R809
+19V OPT +3.3V_Normal +2.5V_Normal

10
S
L802 10uH R875 C890
JK800 JP801 BST SW 4.7uF C895
8 1 22K G

SMAB34
10V 0.1uF
KJA-DC-1-0032 111116

R876
THERMAL
50V

D802
IC810 Q803

40V
10K->22K PMV48XP D AO3407A
VIN EN C840 C814 POWER_ON/OFF1 Q805 AP2114H-2.5TRG1 OPT

0
C812 1K->100

9
4 7 2 S
47uF 10uF 0.1uF VOLTAGE HIGHER C879
11.10.27 25V 10V 50V 11.11.05 R874 C891 R842 G
1000Hr->2000Hr 4.7uF
C803 FREQ COMP 11.11.14 VIN VOUT 22K 10V 12.07.17
2 6 3 0CE476WH6DC(1000hr)-> 100
C820 111129 10uF C 1uF GND OPT D ZXMP3F30FHTA
25V
300K EAE61423901(2000hr) R870 C896 R877 C898 10K->22K
111129 47uF 47uF DEL R815 R851 11.10.27 25V 4.7uF OPT ->AO3407A
100K B Q804 10uF 1
1 Discharging R DEL 25V GND FB 47K 1% POWER_ON/OFF1 10V 10V C899 11.11.15
5 4 MMBT3904(NXP) 1uF
JP800 (0RJ2201J674) 12.03.08 OPT 0.1uF C882
OPT C897 25V
EAE42868301(3225)-> 2K 1% E 50V R843
R819 R855 R873 10uF 1K
EAE61081701(3216)
0 10K 10V
11.11.07 C869 C
11.11.28
6604->6601 220pF PANEL_CTL R839
OPT 1.2K->2K 4.7K
50V R838 B Q802
C808
15K MMBT3904(NXP)
150pF
50V 1%
R816 R840 E
68K 10K

111116
11.12.01 Panel switch deletion
LDO change 111201
19V TO 5V DCDC CONVERTER EAN56716601 (5A) Panel switch recover
R800 ->EAN54428101 (1A)
MULTI_ON +1.8V_TUNER
100K 1%
11.12.20
LDO change
R802
POWER_ON/OFF1 4.7K EAN54428101 (1A) adj
11.11.29 IC805
->EAN54428601 (1A) 3.3v
0.047uF->0.033uF
OPT 150K->180K +5V_USB +5V_Normal AP1117E18G-13
C811
0.47uF IC800 IN 3 1 ADJ/GND
+3.3V_TUNER
16V MP1472GJ-C452-Z IC803 OPT
OPT 11.11.07 12.03.08 R808 2
C835 AP1117E33G-13 R872 C892 C894
C868 0->47 R884 EAE61081701(25V)-> 0 1uF
0.033uF OUT 1 0.1uF
0.01uF R888 180K L803 10uH EAE52158501(10V) 10V
50V 47 BST SS 50V 50V
8 1 IN 3 1 ADJ/GND
C856
2 10uF
IN EN OPT 10V
C852 C858 OUT
7 2 47uF C861
10uF 0.1uF
11.11.14 25V C836 C837
C804 C810 0CE476WH6DC(1000hr)->
10V 50V 10uF 0.1uF C843
10uF 0.1uF SW COMP EAE61423901(2000hr) R865
6 3 10V 50V 1uF
25V 50V 1
10V
12.03.08 R834 OPT
R891 C842 C906
EAE42868301(3225)-> GND FB 47K 33K 1%
EAE61081701(3216) 5 4 10uF 0.1uF
11.11.07 12K 1% 10V 50V 5V TO 1.15V DCDC CONVERTER
0->47K R824 R845
0 OPT M1 Core
C832 R811
MULTI_ON
4700pF 100K 1%
11.11.14 50V R825
2200pF->4700pF C845 10K
330pF +1.15V_VDDC
10K->8.2K 1% R812
150pF->330pF 50V POWER_ON/OFF1 4.7K 11.11.07
R818
8.2K 0.1uF->0.22uF

C819 IC806
+12V_Normal 0.47uF 11.11.07 MP1472GJ-C452-Z
16V C846 OPT
C830 0->47
OPT 0.22uF R898 L806
0.01uF R871
50V 47 BST SS 16V 180K 10uH
R813 8 1
0
IN EN OPT
C855 C862
7 2 47uF C866
10uF 0.1uF
11.11.14 25V
C802 C816 0CE476WH6DC(1000hr)->
10V 50V
10uF 0.1uF SW COMP EAE61423901(2000hr)
10V 50V 6 3

R893 R841
OPT 19V TO 12V DCDC CONVERTER GND FB 47K 1% 2K
MULTI_ON R804 5 4
100K 1%
11.11.07 220 1%
R848 OPT

R831 R830
R805 11.11.29 0->47K C881
0.047uF->0.033uF +12V_Normal 560->220
POWER_ON/OFF1 4.7K 47pF

8.2K 0
C841
150K->180K 8200pF 50V
11.11.07 OPT 12.08.10
IC802 25V

1%
R822 68K->1.8K C850
C813 MP1472GJ-C452-Z 150pF
11.11.07 C841 4700pF->8200pF
0.47uF C838 50V
16V C825 0->47 R885 R822
0.033uF L805 10K->8.2K
OPT 0.01uF R869 180K 1.8K
50V 47 BST SS 50V 10uH
8 1
OPT
IN EN C853 C859 C863
7 2 47uF 10uF 0.1uF
11.11.14 25V 25V 50V
C800 C806 0CE476WH6DC(1000hr)->
10uF 0.1uF SW COMP EAE61423901(2000hr) 3.3V TO 1.5V LDO
25V 50V 6 3
R835 IC807
12.03.08 R892
EAE42868301(3225)-> GND FB 47K 120K TJ4220GDP-ADJ [EP]GND
5 4
EAE61081701(3216) +1.5V_DDR
11.11.07 1% 0
0->47K R826 R846 NC_1 GND
0 5% 2012.08.12 1 8
+3.3V_Normal C833 R835 : 33k -> 120k

THERMAL
4700pF R846 : 12K -> 0 R817
50V R827 POWER_ON/OFF1 4.7K EN2 ADJ/SENSE 1% 5%
11.11.14

9
C847 2 7
2200pF->4700pF 10K
R806 330pF C857
10K->8.2K 1% 10K 0
10K 50V C817 0.01uF R844 R849
OPT R807 150pF->330pF R820 VIN3 VOUT
1K 8.2K +3.3V_AMP 0.1uF 3 6 50V
OLP 50V
OPT OPT
OPT

R832
NC4 NC_2 C864 C867

1%
11.11.29 4 5

1K
Not used : Diode DEL 10uF 0.1uF
0DSKE00048A 10V 50V
only for small(ready)

R833
C805

10K

1%
+3.3V_ST
R879 10uF
0 10V

R814
0

OPT

AO3407A Vgs : 10.8V(24V input) R887

AMP_VCC Control AO3407A Vgs : 10.36V(19V input)
120915 MHL_CD_SENSE 4.7K 5%
19V TO 5V DCDC FOR MHL
121118 MP1584->MP1472
AMP_VCC +19V_SCART DEL
OPTION: (OPT)5V_PWR_FOR_MHL_ONLY
OPT MULTI_ON R903
OPT
C801 C809 100K 1%
C839 R880
10uF 0.1uF 2.2uF
25V 50V 10K OPT
50V Q807 +19V_AMP_VCC
12.03.08 AO3407A S POWER_ON/OFF1 R904
4.7K 11.11.29
EAE42868301(3225)-> 0.047uF->0.033uF
EAE61081701(3216) G OPT 150K->180K +5V_ST
R821 C878
12K
D 0.47uF IC808
L807 3.3uH 16V
11.11.07 MP1472GJ-C452-Z
CPI2520NHL3R3ME 2520 OPT 12.03.08 R901
C872 0->47 C889 R894 0
0.033uF EAE61081701(25V)->
0.01uF R890 180K L801 10uH EAE52158501(10V)
C 50V 47 BST SS 50V
R810 +19V
MULTI_ON C834 C860 C865 8 1
10K B Q806
MMBT3904(NXP) 0.01uF 10uF 0.01uF
50V 25V 50V OPT
IN EN C875 C876
E 7 2 47uF C877
R836 11.11.14 10uF 0.1uF
10K C870 25V 10V
C893 0CE476WH6DC(1000hr)-> 50V
10uF 0.1uF SW COMP EAE61423901(2000hr)
25V 50V 6 3
12.03.08 R899 R889
EAE42868301(3225)-> GND FB 47K 33K 1%
EAE61081701(3216) 5 4
11.11.07 12K 1%
0->47K R896 R900
0
C873
4700pF
11.11.14 50V R897
2200pF->4700pF C874 10K
10K->8.2K 330pF 1%
150pF->330pF 50V
R895
8.2K

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES EAX65077403

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC4_S7LRM 2012.11.18
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. POWER 8 12

Copyright ⓒ 2013 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 11.11.29
+19V Diode change canceled(111202)
23.6" 23.6" EAH61112701->EAH61533501
11.12.02

LED DRIVER WLED_ENABLE

23.6"
R1127
100
11.11.15
1K->100ohm
1000pF->100pF
22uF 2EA->47uF 1EA
EAE60365101->EAE61423901

23.6"
C1118
23.6"
C1121
L1101
33uH
D1103
BR210

100V
+19V

21.6"/26" 21.6"/26"
12.05.17
C1110 EAE62721801 33uF,
C1111 0CH8106J691 10uF
+24V_BLU
23.6" 47uF 4.7uF L1100 D1101 -> EAE60171701 68uF 2EA
23.6"
R1129 C1116 25V 50V 11.11.29 10uH BR210
100K 100pF 0DSKE00048A Diode DEL
1% 50V 21.6"/26"
21.6"/26" 21.6"/26" 21.6"/26" 21.6"/26" 100V 21.6"/26"21.6"/26"21.6"/26"
23.6" C1113 C1115 C1119 21.6"/26" OPT
C1112 R1107 R1109 C1137
10uF 0.1uF 100pF C1135 C1136
IC1100 47uF
25V 50V
220K 30K
68uF 68uF 1uF C1138 C1139
25V 1uF 1uF
DT1641AS [EP]GND
12.01.10 OPT 50V 1/16W 1/16W
35V 35V 50V
50V 50V
12.08.11 D 23.6" 21.6"/26"
270K+270K 23.6" Main AOD478
23.6" Q1103 IC1101
->510K 2012size Sub AP18T10GH [EP]
EN VIN R1136 0 G AOD478 TPS40210DGQR
C1122
1 24 1uF
23.6" S +3.3V_ST

THERMAL
25V
R1100 RC VDD

25
510K OVP VREF 1 10
VOUT 2 23 21.6"/26"

THERMAL
1/8W 23.6" 23.6"

21.6"/26"
23.6" R1105 C1126

21.6"/26"
1%

11
R1128 C1114 NC_1 CS 10K 0.22uF SS BP
R1121 2 9

R1103

1/16W
3 22 21.6"/26" D

10K
100 22K 1000pF 21.6"/26"
WLED_DIM_ADJ 1% 50V 1/16W 16V
R1113 Q1101
R1137 DIS/EN GDRV 3.3 AOD478
PGND_1 NDRV 3 8 G
23.6" 23.6" 4 21 0.1 21.6"/26" C
R1122 C1111 R1101 1/16W
100K 100pF 12.08.11 1% 11.10.27 MULTI_ON 21.6"/26" S
23.6" 23.6" 4.7K B Q1102 R1111
50V 24K->22K PGND_2 RSS R1134 1W Parallel 0ohm DEL
MMBT3904(NXP) COMP ISNS 1K
5 20 R1132 4 7
23.6" 21.6"/26"
30K 1% E21.6"/26" 1/16W

R1115
11.11.15 220K 1% 23.6"

21.6"/26"
R1114
R1102 21.6"/26"21.6"/26"

21.6"/26"
1000pF->100pF FB GND

0.1
C1123

0.1
PDIM COMP 10K

1W
5 6

1W
6 19 C1117 C1120 21.6"/26"21.6"/26" 21.6"/26"
23.6" 23.6" 23.6" 4700pF 2200pF 47pF C1131 C1132 C1134
R1123 50V 50V 50V 1uF 0.1uF 100pF
100K RISET RT R1131 R1133 C1125
BLU_CURRENT_CTL 7 18 R1135 25V 25V 50V
1% 23.6" 39K 1% 1.5K 1% 21.6"/26"
R1124 1.5K 1% 0.047uF R1108
LS8 LS1 23.6" 25V R1104 51K
1.5K 8 17 23.6"
1% 470K 1/16W 121118 121118

21.6"/26"
R1106

1/16W
1.5K
R1125 1/16W C1132 C1132
LS7 LS2 21.6"/26"
24K 9 16 0CK105CD56A 0CK104BF56A
12.05.17 To improve audible noise ->0CK105CK56A ->0CK104BH56A
1% C1103 2200pF->47pF
23.6" JP1104
LS6 LS3 C1105 47pF->OPT
10 15
JP1103 12.07.03 To improve backlight blinking
C1103 47pF->2200pF
JP1100 LS5 LS4 C1105 47pF->Apply
11 14 JP1107
R1103 18K->470K

NC_2 LGND JP1108

JP1101 12 13

JP1105
12.10.16
EAN62407801->EAN62656301

JP1106

VOUT
JP1102

21.6"/26"
P1101
+24V_BLU SM14B-SRSS-TB
13
23.6" 23.6" 23.6" OPT OPT JP1088
C1124 C1127 C1128 C1129 C1130
12 33uF 1uF 1uF 1uF 1uF 24V 1
100V 100V 100V 100V 100V

11 24V 2

12.03.08
10 EAE61103401 2.2uF MLCC 1ea(3225) 24V 3
->EAE61381601 1uF MLCC 2ea(3216)

9 24V 4

8 24V 5

7 GND 6

6 GND
7

5 GND 8

4 GND 9

3 GND 10
OPT
JP1109
R1110
2 100 ERROR_OUT
ERROR_OUT 11
1/16W
JP1110
1 INV_ON
WLED_ENABLE 12

OPT
R1112

1/16W
NC 13
05002HR-H12J05

0
JP1111
P1100 PWN_DIM
23.6" WLED_DIM_ADJ 14

OPT C1133
1uF 15
10V
GND

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES EAX65077403

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC4_S7LRM 2012.11.18
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. LED DRIVER 11 12

Copyright ⓒ 2013 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 AVDD_DDR0 AVDD_DDR0 AVDD_DDR0 AVDD_DDR0

+1.5V_DDR AVDD_DDR0

R1227
R1201

R1224
R1204

1K 1%
1K 1%

1K 1%
1K 1%

L1202
CIC21J501NE

A-MVREFDQ B-MVREFCA B-MVREFDQ

0.1uF
A-MVREFCA

1000pF
0.1uF

1000pF

0.1uF
1000pF
OPT
0.1uF

1000pF

1%
1%

1%
1%

C1250

R1228

C1217

C1218

C1219

C1238

C1241
R1202

R1225

0.1uF

0.1uF

0.1uF
R1205

C1206

C1239

C1220
10uF
C1247

C1248

C1249

C1251

1uF

1uF

1uF

1uF

1uF
C1202
C1201

C1204

1K
C1203
1K

1K
1K

CLose to DDR3 CLose to Saturn7M IC CLose to Saturn7M IC CLose to DDR3

EAN61836301
EAN61848802 IC1202
IC1201 K4B1G1646G-BCK0
K4B2G1646E-BCK0 IC101
MSD804KKX DDR_1600_SS
DDR_2G_1600_SS N3 M8
B-MA0 A0 VREFCA B-MVREFCA
A-MVREFCA
M8
VREFCA A0
N3
P7
A-MA0
A11
S7LR-M_NON_MS10 B23
B-MA1
P7
P3
A1
A1 A-MA1 A-MA0 A_DDR3_A[0] B_DDR3_A[0] B-MA0 B-MA2 A2
P3 C14 D25 N2 H1
A2 A-MA2 A-MA1 A_DDR3_A[1] B_DDR3_A[1] B-MA1 B-MA3 A3 VREFDQ B-MVREFDQ
H1 N2 B11 F22 P8
A-MVREFDQ VREFDQ A3 A-MA3 A-MA2 A_DDR3_A[2] B_DDR3_A[2] B-MA2 B-MA4 A4
P8 F12 G22 P2
A4 A-MA4 A-MA3 A_DDR3_A[3] B_DDR3_A[3] B-MA3 B-MA5 A5 R1226
P2 C15 E24 R8 L8
R1203 A5 A-MA5 A-MA4 A_DDR3_A[4] B_DDR3_A[4] B-MA4 B-MA6 A6 ZQ
L8 R8 E12 F21 R2 240
ZQ A6 A-MA6 A-MA5 A_DDR3_A[5] B_DDR3_A[5] B-MA5 B-MA7 A7
240 R2 A14 E23 T8 1% AVDD_DDR0
A7 A-MA7 A-MA6 A_DDR3_A[6] B_DDR3_A[6] B-MA6 B-MA8 A8
AVDD_DDR0 1% T8 D11 D22 R3 B2
A8 A-MA8 A-MA7 A_DDR3_A[7] B_DDR3_A[7] B-MA7 B-MA9 A9 VDD_1
B2 R3 B14 D24 L7 D9 C1227 10uF
VDD_1 A9 A-MA9 A-MA8 A_DDR3_A[8] B_DDR3_A[8] B-MA8 B-MA10 A10/AP VDD_2
D9 L7 D12 D21 R7 G7 C1228 0.1uF
C1205 10uF VDD_2 A10/AP A-MA10 A-MA9 A_DDR3_A[9] B_DDR3_A[9] B-MA9 B-MA11 A11 VDD_3
G7 R7 C16 C24 N7 K2 C1229 0.1uF
C1207 0.1uF VDD_3 A11 A-MA11 A-MA10 A_DDR3_A[10] B_DDR3_A[10] B-MA10 B-MA12 A12/BC VDD_4
K2 N7 C13 C25 T3 K8 C1230 0.1uF
C1208 0.1uF A-MA12 A-MA11 B-MA11 B-MA13
VDD_4 A12/BC A_DDR3_A[11] B_DDR3_A[11] A13 VDD_5 C1231 0.1uF
C1210 0.1uF K8 T3 A15 F23 N1
VDD_5 A13 A-MA13 A-MA12 A_DDR3_A[12] B_DDR3_A[12] B-MA12 VDD_6
N1 E11 E21 M7 N9 C1232 0.1uF
C1211 0.1uF A-MA13 B-MA13
VDD_6 A_DDR3_A[13] B_DDR3_A[13] NC_5 VDD_7 C1233 0.1uF
C1212 0.1uF N9 M7 B13 D23 R1
VDD_7 NC_5 A-MA14 A_DDR3_A[14] B_DDR3_A[14] B-MA14 VDD_8
R1 M2 R9 C1234 0.1uF
C1213 0.1uF B-MBA0
VDD_8 BA0 VDD_9 C1235 0.1uF
C1214 0.1uF R9 M2 B-MCK N8
VDD_9 BA0 A-MBA0 A-MCK B-MBA1 BA1
R1235

N8 F13 G20 M3 C1236 0.1uF

56
R1237
C1215 0.1uF A-MBA1 A-MBA0 B-MBA0 B-MBA2
1%

BA1 A_DDR3_BA[0] B_DDR3_BA[0] BA2

1%
M3 B15 F24 A1
56

C1216 0.1uF A-MBA2 A-MBA1 B-MBA1 C1240

BA2 A_DDR3_BA[1] B_DDR3_BA[1] VDDQ_1
A1 C1209 E13 F20 J7 A8
VDDQ_1 A-MBA2 A_DDR3_BA[2] B_DDR3_BA[2] B-MBA2 0.01uF CK VDDQ_2
R1236

A8 J7 K7 C1

56
R1238
0.01uF 50V
1%

VDDQ_2 CK CK VDDQ_3

1%
C1 K7 50V C17 G25 K9 C9
56

VDDQ_3 CK A-MCK A_DDR3_MCLK B_DDR3_MCLK B-MCK B-MCKE CKE VDDQ_4

C9 K9 A17 G23 B-MCKB D2
VDDQ_4 CKE A-MCKE A-MCKB A_DDR3_MCLKZ B_DDR3_MCLKZ B-MCKB VDDQ_5
D2 B16 F25 L2 E9
VDDQ_5 A-MCKB A-MCKE A_DDR3_MCLKE B_DDR3_MCLKE B-MCKE CS VDDQ_6
E9 L2 K1 F1
VDDQ_6 CS B-MODT ODT VDDQ_7
F1 K1 J3 H2
VDDQ_7 ODT A-MODT AVDD_DDR0 B-MRASB RAS VDDQ_8
H2 J3 E14 D20 K3 H9
VDDQ_8 RAS A-MRASB AVDD_DDR0 A-MODT A_DDR3_ODT B_DDR3_ODT B-MODT B-MCASB CAS VDDQ_9
H9 K3 B12 B25 L3
VDDQ_9 CAS A-MCASB R1231 A-MRASB A_DDR3_RASZ B_DDR3_RASZ B-MRASB R1232 B-MWEB WE
L3 A12 B24 10K J1
WE A-MWEB 10K A-MCASB A_DDR3_CASZ B_DDR3_CASZ B-MCASB NC_1
J1 C12 A24 T2 J9
NC_1 A-MWEB A_DDR3_WEZ B_DDR3_WEZ B-MWEB B-MRESETB RESET NC_2
J9 T2 L1
NC_2 RESET A-MRESETB NC_3
L1 F11 E20 L9
NC_3 A-MRESETB A_DDR3_RESET B_DDR3_RESET B-MRESETB NC_4
L9 F3 T7
NC_4 B-MDQSL DQSL NC_6 B-MA14
T7 F3 G3
A-MA14 NC_6 DQSL A-MDQSL B-MDQSLB DQSL
G3 B19 K24
DQSL A-MDQSLB A-MDQSL A_DDR3_DQSL B_DDR3_DQSL B-MDQSL
C18 K25 C7 A9
A-MDQSLB A_DDR3_DQSLB B_DDR3_DQSLB B-MDQSLB B-MDQSU DQSU VSS_1
A9 C7 B7 B3
VSS_1 DQSU A-MDQSU B-MDQSUB DQSU VSS_2
B3 B7 B18 J21 E1
VSS_2 DQSU A-MDQSUB A-MDQSU A_DDR3_DQSU B_DDR3_DQSU B-MDQSU VSS_3
E1 A18 J20 E7 G8
VSS_3 A-MDQSUB A_DDR3_DQSUB B_DDR3_DQSUB B-MDQSUB B-MDML DML VSS_4
G8 E7 D3 J2
VSS_4 DML A-MDML B-MDMU DMU VSS_5
J2 D3 E15 H24 J8
VSS_5 DMU A-MDMU A-MDML A_DDR3_DQML B_DDR3_DQML B-MDML VSS_6
J8 A21 L20 E3 M1
VSS_6 A-MDMU A_DDR3_DQMU B_DDR3_DQMU B-MDMU B-MDQL0 DQL0 VSS_7
M1 E3 F7 M9
VSS_7 DQL0 A-MDQL0 B-MDQL1 DQL1 VSS_8
M9 F7 D17 L23 F2 P1
VSS_8 DQL1 A-MDQL1 A-MDQL0 A_DDR3_DQL[0] B_DDR3_DQL[0] B-MDQL0 B-MDQL2 DQL2 VSS_9
P1 F2 G15 J24 F8 P9
VSS_9 DQL2 A-MDQL2 A-MDQL1 A_DDR3_DQL[1] B_DDR3_DQL[1] B-MDQL1 B-MDQL3 DQL3 VSS_10
P9 F8 B21 L24 H3 T1
VSS_10 DQL3 A-MDQL3 A-MDQL2 A_DDR3_DQL[2] B_DDR3_DQL[2] B-MDQL2 B-MDQL4 DQL4 VSS_11
T1 H3 F15 J23 H8 T9
VSS_11 DQL4 A-MDQL4 A-MDQL3 A_DDR3_DQL[3] B_DDR3_DQL[3] B-MDQL3 B-MDQL5 DQL5 VSS_12
T9 H8 B22 M24 G2
VSS_12 DQL5 A-MDQL5 A-MDQL4 A_DDR3_DQL[4] B_DDR3_DQL[4] B-MDQL4 B-MDQL6 DQL6
G2 F14 H23 H7
DQL6 A-MDQL6 A-MDQL5 A_DDR3_DQL[5] B_DDR3_DQL[5] B-MDQL5 B-MDQL7 DQL7
H7 A22 M23 B1
DQL7 A-MDQL7 A-MDQL6 A_DDR3_DQL[6] B_DDR3_DQL[6] B-MDQL6 VSSQ_1
B1 D15 K23 D7 B9
VSSQ_1 A-MDQL7 A_DDR3_DQL[7] B_DDR3_DQL[7] B-MDQL7 B-MDQU0 DQU0 VSSQ_2
B9 D7 C3 D1
VSSQ_2 DQU0 A-MDQU0 B-MDQU1 DQU1 VSSQ_3
D1 C3 G16 G21 C8 D8
VSSQ_3 DQU1 A-MDQU1 A-MDQU0 A_DDR3_DQU[0] B_DDR3_DQU[0] B-MDQU0 B-MDQU2 DQU2 VSSQ_4
D8 C8 B20 L22 C2 E2
VSSQ_4 DQU2 A-MDQU2 A-MDQU1 A_DDR3_DQU[1] B_DDR3_DQU[1] B-MDQU1 B-MDQU3 DQU3 VSSQ_5
E2 C2 F16 H22 A7 E8
VSSQ_5 DQU3 A-MDQU3 A-MDQU2 A_DDR3_DQU[2] B_DDR3_DQU[2] B-MDQU2 B-MDQU4 DQU4 VSSQ_6
E8 A7 C21 K20 A2 F9
VSSQ_6 DQU4 A-MDQU4 A-MDQU3 A_DDR3_DQU[3] B_DDR3_DQU[3] B-MDQU3 B-MDQU5 DQU5 VSSQ_7
F9 A2 E16 H20 B8 G1
VSSQ_7 DQU5 A-MDQU5 A-MDQU4 A_DDR3_DQU[4] B_DDR3_DQU[4] B-MDQU4 B-MDQU6 DQU6 VSSQ_8
G1 B8 A20 L21 A3 G9
VSSQ_8 DQU6 A-MDQU6 A-MDQU5 A_DDR3_DQU[5] B_DDR3_DQU[5] B-MDQU5 B-MDQU7 DQU7 VSSQ_9
G9 A3 D16 H21
VSSQ_9 DQU7 A-MDQU7 A-MDQU6 A_DDR3_DQU[6] B_DDR3_DQU[6] B-MDQU6
C20 K21
A-MDQU7 A_DDR3_DQU[7] B_DDR3_DQU[7] B-MDQU7

1G 1600
2G 1600
DDR_1600_HYNIX_9003(DEV)
IC1202-*1 DDR_2G_1600_HYNIX
H5TQ1G63EFR-PBC IC1201-*1
H5TQ2G63DFR-PBC
N3 M8
A0 VREFCA
P7 N3 M8
A1 A0 VREFCA
P3 P7
A2 A1
N2 H1 P3
A3 VREFDQ A2
P8 N2 H1
A4 A3 VREFDQ
P2 P8
A5 A4
R8 L8 P2
A6 ZQ A5
R2 R8 L8
A7 A6 ZQ
T8 R2
A8 A7
R3 B2 T8
A9 VDD_1 A8
L7 D9 R3 B2
A10/AP VDD_2 A9 VDD_1
R7 G7 L7 D9
A11 VDD_3 A10/AP VDD_2
N7 K2 R7 G7
A12/BC VDD_4 A11 VDD_3
T3 K8 N7 K2
NC_7 VDD_5 A12/BC VDD_4
N1 T3 K8
VDD_6 A13 VDD_5
M7 N9 N1
NC_5 VDD_7 VDD_6
R1 M7 N9
VDD_8 NC_5 VDD_7
M2 R9 R1
BA0 VDD_9 VDD_8
N8 M2 R9
BA1 BA0 VDD_9
M3 N8
BA2 BA1
A1 M3
VDDQ_1 BA2
J7 A8 A1
CK VDDQ_2 VDDQ_1
K7 C1 J7 A8
CK VDDQ_3 CK VDDQ_2
K9 C9 K7 C1
CKE VDDQ_4 CK VDDQ_3
D2 K9 C9
VDDQ_5 CKE VDDQ_4
L2 E9 D2
CS VDDQ_6 VDDQ_5
K1 F1 L2 E9
ODT VDDQ_7 CS VDDQ_6
J3 H2 K1 F1
RAS VDDQ_8 ODT VDDQ_7
K3 H9 J3 H2
CAS VDDQ_9 RAS VDDQ_8
L3 K3 H9
WE CAS VDDQ_9
J1 L3
NC_1 WE
T2 J9 J1
RESET NC_2 NC_1
L1 T2 J9
NC_3 RESET NC_2
L9 L1
NC_4 NC_3
F3 T7 L9
DQSL NC_6 NC_4
G3 F3 T7
DQSL DQSL NC_6
G3
C7 A9 DQSL
DQSU VSS_1
B7 B3 C7 A9
DQSU VSS_2 DQSU VSS_1
E1 B7 B3
VSS_3 DQSU VSS_2
E7 G8 E1
DML VSS_4 VSS_3
D3 J2 E7 G8
DMU VSS_5 DML VSS_4
J8 D3 J2
VSS_6 DMU VSS_5
E3 M1 J8
DQL0 VSS_7 VSS_6
F7 M9 E3 M1
DQL1 VSS_8 DQL0 VSS_7
F2 P1 F7 M9
DQL2 VSS_9 DQL1 VSS_8
F8 P9 F2 P1
DQL3 VSS_10 DQL2 VSS_9
H3 T1 F8 P9
DQL4 VSS_11 DQL3 VSS_10
H8 T9 H3 T1
DQL5 VSS_12 DQL4 VSS_11
G2 H8 T9
DQL6 DQL5 VSS_12
H7 G2
DQL7 DQL6
B1 H7
VSSQ_1 DQL7
D7 B9 B1
DQU0 VSSQ_2 VSSQ_1
C3 D1 D7 B9
DQU1 VSSQ_3 DQU0 VSSQ_2
C8 D8 C3 D1
DQU2 VSSQ_4 DQU1 VSSQ_3
C2 E2 C8 D8
DQU3 VSSQ_5 DQU2 VSSQ_4
A7 E8 C2 E2
DQU4 VSSQ_6 DQU3 VSSQ_5
A2 F9 A7 E8
DQU5 VSSQ_7 DQU4 VSSQ_6
B8 G1 A2 F9
DQU6 VSSQ_8 DQU5 VSSQ_7
A3 G9 B8 G1
DQU7 VSSQ_9 DQU6 VSSQ_8
A3 G9
DQU7 VSSQ_9

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES EAX65077403

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC4_S7LRM 2012.11.18
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. DDR 12 12

Copyright ⓒ 2013 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 * Option name of this page : CI_SLOT
(because of Hong Kong)
CI Region
CI SLOT

+5V_CI_ON

CI_DATA[0-7]

CI TS INPUT

AR1905 33

CI_DATA[0-7]
FE_TS_DATA[7]
+5V_Normal CI_MDI[7]
C1906 FE_TS_DATA[6]

FE_TS_DATA[0-7]
CI_MDI[6]
10uF FE_TS_DATA[5]
10V P1900 CI_MDI[5]
FE_TS_DATA[4]
R1903 EAG41860102 CI_MDI[4]
10K
10067972-000LF
/CI_CD1 CI_SLOT AR1906 33
FE_TS_DATA[3]
C1903 CI_MDI[3]
0.1uF FE_TS_DATA[2]
R1908 CI_MDI[2]
16V 35 FE_TS_DATA[1]
100 CI_MDI[1]
36 CI_DATA[3] FE_TS_DATA[0]
AR1901 CI_MDI[0]

CI_DATA[0-7]
37 3 CI_DATA[4]
33 R1921
38 4 CI_DATA[5] 10K FE_TS_DATA[0-7]
CI_TS_DATA[4]
39 5 CI_DATA[6]
CI_TS_DATA[5] R1929 33
40 6 CI_DATA[7] CI_MISTRT FE_TS_SYNC
CI_TS_DATA[6] R1930 33
CI_TS_DATA[7] 41 7 R1919 47 FE_TS_VAL_ERR
/PCM_CE CI_MIVAL_ERR
42 8 CI_ADDR[10]
R1931 100
R1905 10K 43 9 FE_TS_CLK
CI_OE CI_MCLKI
44 10 CI_ADDR[11]
CI_IORD
CI_ADDR[9] +5V_Normal
CI_IOWR 45 11
46 12 CI_ADDR[8] 120915
47 13 CI_ADDR[13] R1911 Array->normal resistor
CI_MDI[0] 10K 120915
48 14 CI_ADDR[14] ADDED
CI_MDI[1]
CI_MDI[2] 49 15 CI_WE
50 16 R1920 100
CI_MDI[3] /PCM_IRQA
51 17
OPT OPT C1915 120915 BufferIC change 121022 BufferIC change
C1905 52 18 C1909
GND 0.1uF R1910 0 R1916 0 0.1uF 0.1uF 120915 0ITO742440D 0ISTLPH048A
120915 CI_MDI[4] 53 19 16V ADDED
ADDED GND ->0ISTLPH048A ->0ITO742440D
CI_MDI[5] 54 20
+5V_Normal CI_ADDR[12]
CI_MDI[6] 55 21 CLOSE TO MSTAR
CI_ADDR[7] GND
R1928
10K
CI_MDI[7]
R1906 10K
56
57
22
23 CI_ADDR[6]
CI HOST I/F
R1902 47 58 24 CI_ADDR[5]
PCM_RST
R1901 47 59 25 CI_ADDR[4]
/PCM_WAIT
CLOSE TO MSTAR 60 26 CI_ADDR[3] +3.3V_Normal
REG
R1925 100 61 27 CI_ADDR[2]
CI_TS_CLK
R1926 33 CI_ADDR[1] NAND_EN
CI_TS_VAL 62 28
R1927 33 63 29 CI_ADDR[0]
CI_TS_SYNC CI_DET
CI_DATA[0] IC1902
64 30
AR1903 33 CI_DATA[1] C1913
65 31 CI_ADDR[0-14]
CI_TS_DATA[0] CI_DATA[2] 0.1uF
66 32 1OE VCC 16V
CI_TS_DATA[1] 67 33 1 20
TOSHIBA
CI_TS_DATA[2] 68 34
CI_TS_DATA[3] 1A1 2OE
OPT G2
2 69 G1
1 PCM_A[0] 2 19
R1909 AR1915
R1907 0 0ITO742440D AR1914
100 33 33
2Y4 1Y1
/CI_CD2 3 18
CI_ADDR[7] CI_ADDR[0]
+5V_Normal GND
CI_ADDR[6] CI_ADDR[1]
CI_ADDR[5] 1A2 2A4 CI_ADDR[2]
GND PCM_A[1] 4 17 PCM_A[7]
C1914 CI_ADDR[4] CI_ADDR[3]
2pF
R1904 2Y3 1Y2

TC74LCX244FT
50V 5 16
10K GND
CLOSE TO MSTAR C1904
1A3 2A3
0.1uF 6 15
PCM_A[2] PCM_A[6]
16V

2Y2 1Y3
7 14
CI_MISTRT
CI_MIVAL_ERR
1A4 2A2
PCM_A[3] 8 13 PCM_A[5]
CI_MCLKI
2Y1 1Y4
9 12

GND 2A1
10 11 PCM_A[4]

CI DETECT

+3.3V_CI +3.3V_CI
+3.3V_Normal +3.3V_CI
IC1901
74LVC1G32GW

B 1 5 VCC
/CI_CD2
L1901 A 2
/CI_CD1 C1908 R1917
0 0.1uF
GND 3 4 Y 10K
16V

GND R1915 AR1907 33

OPT 47 CI_DATA[0] PCM_D[0]
C1901 C1902 CI_DET CI_DATA[1] PCM_D[1]
0.1uF 0.1uF R1918

CI_DATA[0-7]
47 CI_DATA[2] PCM_D[2]
/PCM_CD CI_DATA[3] PCM_D[3]

PCM_D[0-7]
AR1908 33
CI_DATA[4] PCM_D[4]
CI_DATA[5] PCM_D[5]
CI_DATA[6] PCM_D[6]
CI_DATA[7] PCM_D[7]

121022 Swich block change PCM_D[0-7]

FET->IC CI_DATA[0-7]

CI POWER ENABLE CONTROL

AR1912 33
CI_ADDR[8] PCM_A[8]
CI_ADDR[9] PCM_A[9]
CI_ADDR[10] PCM_A[10]
+5V_Normal IC1903 CI_ADDR[11] PCM_A[11]
AP2151WG-7 +5V_CI_ON
L1902
BLM18PG121SN1D
IN OUT AR1913 33
5 1
CI_ADDR[12] PCM_A[12]
GND CI_ADDR[13] PCM_A[13]
2 CI_ADDR[14] PCM_A[14]
R1922
C1910
100K REG /PCM_REG
R1914 1uF
100 EN FLG 25V
PCM_5V_CTL 4 3

R1913
10K AR1909 33
CI_OE /PCM_OE
CI_WE /PCM_WE
CI_IORD /PCM_IORD
CI_IOWR /PCM_IOWR

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES EAX65077403

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC4_S7LRM 2012.11.18
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. PCMCI 19 12

Copyright ⓒ 2013 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 NETCAST4.0 EU(DVB-T/C)_TUNER_BLOCK

(OPT)RF_SW_OPT
R2603
121118 0
Change Tuner RF_SWITCH_CTL
Tuner ->Tuner(with bushing) +3.3V_TU
C2603 Close to TUNER
0.1uF
TU2600 16V
(OPT)RF_SW_OPT
R2614
TDSS-G501D(B) R2611
100K
12.08.14
diagonal noise improve 100
TUNER_RESET
OPT
C2624 C2622
0.1uF 0.1uF
16V (OPT)TU_I2C_FILTER 16V
R2609-*1
MLG1005SR27JT
+3.3V_TU

NC_1 (OPT)TU_I2C_FILTER
1 R2610-*1
MLG1005SR27JT
RESET R2870 R2871
2 1K 1K

TU_I2C_NON_FILTER +3.3V_TU
SCL R2609 33
3 TU_SCL +3.3V_TU
+3.3V_TU
SDA TU_I2C_NON_FILTER
4 R2610 33
TU_SDA OPT OPT
C2607 C2612 C2651 C2652 R2618
20pF 20pF 470 R2619
3.3V 20pF 20pF 82
5 50V 50V 50V 50V close to TUNER TU_SIF
C2621 C2623 C2628
E R2624 R2625
NC_2 +1.8V_TUNER 100pF 0.1uF 100uF OPT 220 220
50V 16V 16V C2626
6 Q2600 OPT OPT
OPT OPT B MMBT3906(NXP)
0.1uF
1.8V 16V R2616
7 OPT 4.7K C
TU_CVBS
C2602 C2604 C2627
E
NC_3 100pF 0.1uF 100uF
R2638 0
8 50V 16V 16V Q2601
OPT OPT B MMBT3906(NXP)
IF_AGC OPT
9 IF_AGC_MAIN C
R2635 R2637
680 680
DLIF_[P] R2608 OPT R2636 OPT
10 C2600 0 should be guarded by ground 2K
0.1uF OPT
DLIF_[N] 16V R2602
11 10
IF_P_MSTAR
B1 A1
B1 A1 IF_N_MSTAR
R2601
10

12 121118
0->10ohm
DEMOD_RESET
SHIELD
This was being applied to the only china demod,
so this has to be deleted in both main and ISDB sheet.
IF_AGC_SEL
LNA2_CTL

+3.3V_TU +3.3V_TUNER
121118
SS BEAD->SUNLORD BEAD

L2606
UBW2012-121F

C2643 C2644 C2646 C2648

22uF 0.1uF 22uF 0.1uF
10V 16V 10V 16V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES EAX65077403

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS NC4_S7LRM 2012.11.18
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. TUNER_EU 26 12

Copyright ⓒ 2013 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
 SCART / COMPONENT&CVBS

COMPONENT&CVBS COMP_NON_ADC_FILTER
(OPT)COMP_ADC_FILTER_L L2807-*1
SCART AMP
L2807 0
CM2012FR10KT
COMP_Y+/AV_CVBS_IN 121118
121017
(OPT)COMP_ADC_FILTER (OPT)COMP_ADC_FILTER
+3.3V_Normal SCART AMP IC change +5V_USB
5.6B R2822 C2829 C2830
Change ZD2806 75 47pF 47pF
5.6B 50V 50V
ZD2807
R2837
10K R2838
1K
C2817
AV_CVBS_DET
0.1uF
OPT
IC2800 50V
D2817 C2813 AZ4580MTR-E1
5.6V COMP_NON_ADC_FILTER 0.1uF
L2806-*1 16V R2847
0 2.2K OUT1 8 VCC
(OPT)COMP_ADC_FILTER_L 1
L2806 DTV/MNT_L_OUT
121128 CM2012FR10KT
[GN]E-LUG Change C2821 R2852 R2846
COMP_Pb+ 33K IN1- 7 OUT2 2.2K
10uF R2851 2
6A (OPT)COMP_ADC_FILTER 16V DTV/MNT_R_OUT
[GN]O-SPRING (OPT)COMP_ADC_FILTER 470K
5.6B R2824
ZD2802 C2827 C2828 R2853
75 IN1+ IN2- 33K C2822
5A JP2810 47pF 47pF 3 6 10uF
5.6B R2854
[GN]CONTACT 50V 50V C2823 10K R2850 16V
ZD2803 33pF 470K
R2855
4A JP2811 VEE IN2+ 10K
[BL]E-LUG-S COMP_NON_ADC_FILTER 4 5
(OPT)COMP_ADC_FILTER_L L2805-*1
L2805 C2824
7B 0 33pF
121017 CM2012FR10KT
[BL]O-SPRING R2848
Change COMP_Pr+
5.6B 5.6K
5B ZD2804 (OPT)COMP_ADC_FILTER +3.3V_Normal SCART1_Lout R2849
[RD]E-LUG-S JP2814 (OPT)COMP_ADC_FILTER 5.6K
5.6B R2823 C2825
C2826 SCART1_Rout
ZD2805 75 47pF 330pF 220K
7C 47pF C2820 R2845
[RD]O-SPRING_1 50V
50V
R2841 R2843 C2819
5C 10K 220K 330pF
JP2815 R2842
[RD]CONTACT_1 1K
(OPT)COMP_ADC_FILTER_L(AUDIO) COMP_DET
4C L2811 R2832
CM2012FR10KT 10K OPT
COMP_L_IN D2818 CLOSE TO MSTAR
5D (OPT)ESD COMP AUDIO IN C2837 C2810 R2834
[WH]O-SPRING JP2812 R2825 5.6V
D2815 1000pF 47pF 12K
20V 470K CLOSE TO MSTAR
50V 50V
4E (OPT)COMP_ADC_FILTER(AUDIO)COMP_NON_ADC_FILTER(AUDIO)
[RD]CONTACT_2 L2811-*1
(OPT)COMP_ADC_FILTER_L(AUDIO) 0
L2812 R2831
5E [RD]O-SPRING_2 CM2012FR10KT 10K
JP2813 COMP_R_IN
(OPT)ESD COMP AUDIO IN
6E [RD]E-LUG D2816 C2838 C2811 R2833
20V R2826 1000pF 47pF 12K
PPJ234-05 470K 50V 50V
JK2800 (OPT)COMP_ADC_FILTER(AUDIO)
COMP_NON_ADC_FILTER(AUDIO)
L2812-*1
0

121019
ADC_FILTER(AUDIO) ADD

121118
+3.3V_Normal

FULL SCART
Change

+3.3V_Normal
[SCART AUDIO MUTE] +3.3V_ST

R2808 (OPT)EU_SCART mute

4.7K R2844
R2810 DTV/MNT_L_OUT (OPT)EU_SCART mute
1K 10K
SCART1_DET R2839
(OPT)EU_SCART mute 2K (OPT)EU_SCART mute
OPT Q2802 D2819
IC2801 C2812 (OPT)EU_SCART mute MMBD6100
D2810 MMBT3904(NXP) Q2804
20V MM1756DURE 0.1uF MMBT3906(NXP) A2
C2814 SCART1_MUTE
R2809 C
0 0.1uF
SC1_SOG_IN VCC IN (OPT)EU_SCART mute A1
6 1 3 1 SB_MUTE
DTV/MNT_VOUT DTV/MNT_R_OUT R2840
(OPT)EU_SCART mute 2K C2816
2
PS GND 0.1uF
SC1_CVBS_IN 5 2 Q2803
OPT MMBT3904(NXP) (OPT)EU_SCART mute
C2802
R2807 C2800 220pF OUT BIAS
75 47pF 4 3
AV_DET 5.6B 50V 50V
22 ZD2800
COM_GND 5.6B C2815
ZD2801 4.7uF
21
SYNC_IN JP2802
20 R2816
SYNC_OUT JP2803 75
19 OPT
SYNC_GND2 R2815
D2802 OPT 22
18 20V D2809
SYNC_GND1 20V SC1_FB
17 (OPT)SCART_ADC_FILTER_L
JP2804
RGB_IO L2808 R2811
16 CM2012FR10KT 75
R_OUT JP2805
15 (OPT)SCART_ADC_FILTER (OPT)SCART_ADC_FILTER SC1_R+
RGB_GND 120927 D2803 R2806 C2831 C2832
14 OPT->APPLY 20V 75 47pF 47pF
SCART_NON_ADC_FILTER
R_GND 50V 50V L2808-*1
13 (OPT)SCART_ADC_FILTER_L 0
D2B_OUT L2809
12 CM2012FR10KT
G_OUT
11 (OPT)SCART_ADC_FILTER (OPT)SCART_ADC_FILTER SC1_G+
D2B_IN 120927 D2804 C2833 C2834
R2802 SCART_NON_ADC_FILTER
10 OPT->APPLY 20V 47pF 47pF
G_GND 75 50V 50V L2809-*1
0 R2814
9 (OPT)SCART_ADC_FILTER_L
ID JP2800 L2810 15K
8 CM2012FR10KT SC1_ID
B_OUT JP2801
7 SC1_B+ D2811
(OPT)SCART_ADC_FILTER (OPT)SCART_ADC_FILTER R2817
AUDIO_L_IN JP2806
D2805 20V
R2803 C2835 C2836 3.9K
6 20V SCART_NON_ADC_FILTER
B_GND 75 47pF 47pF
L2810-*1
50V 50V 0
5
AUDIO_GND 120927
4 OPT->APPLY
(OPT)SCART_ADC_FILTER_L(AUDIO)
AUDIO_L_OUT JP2807 L2813 SCART_NON_ADC_FILTER(AUDIO)R2812
3 CM2012FR10KT L2813-*1 10K
AUDIO_R_IN JP2808 0 SC1_L_IN
2 OPT
AUDIO_R_OUT JP2809 R2804 C2839 C2840 C2805 R2818
D2806 470K 1000pF 47pF 330pF 12K
1 20V 50V
50V 50V

121128 (OPT)SCART_ADC_FILTER(AUDIO)

JK2801 (OPT)ESD SCART Audio IN (OPT)SCART_ADC_FILTER_L(AUDIO)

L2814 R2813
PSC008-01 CM2012FR10KT SCART_NON_ADC_FILTER(AUDIO)10K
L2814-*1
0 OPT SC1_R_IN
C2842 C2806
D2808 R2805 C2841
470K 47pF 330pF R2819
20V 1000pF 12K
50V 50V 50V

121128
(OPT)SCART_ADC_FILTER(AUDIO)
(OPT)ESD SCART Audio IN
121019
ADC_FILTER(AUDIO) ADD
DTV/MNT_L_OUT
OPT OPT OPT
D2807 C2803 C2807
5.6V 1000pF 4700pF
50V

DTV/MNT_R_OUT
OPT OPT OPT
D2800 C2808
C2804 4700pF
5.6V
1000pF
50V

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATES EAX65077403

SPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.
FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS GP4L_S7LR2 2012.11.18
ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FOR
THE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. SCART&COMP 28 12

Copyright ⓒ 2013 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes