Scribd
Upload
48 views

Q BANK - Microcontrollers

Uploaded by

sarvesh.bobade22
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
48 views

Q BANK - Microcontrollers

Uploaded by

sarvesh.bobade22
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Unit 1- CO1

1. Compare Microprocessor Vs Microcontroller


2) Explain the Flag register of 8086 microprocessor
3) Explain the functions of EIU and BU units of 8086 microprocessor.
4) Draw &Explain 8086 Microprocessor architecture in detail
5)Draw &Explain 8051 Micro controller architecture in detail
6)List down the features of 8051 microcontroller
7) Draw &Explain 8051 Micro controller pin diagram in detail
8)Describe the PSW register of 8051 microcontroller
9) Explain memory organization of 8051
10) What are the different addressing modes of 8051
11) Explain the following instructions (i)DJNZ (ii)AJMP (iii)RETI i)
CJNE ii) DEC
12) Write a assembly language programs to find the biggest number from
the array of given numbers
13) Write a assembly language programs to transfer a block of 5 byte from
source location 4000H in external memory to destination 20H in internal
memory
14) Write a assembly language programs to transfer a block of 10 byte
from source location 20H in internal memory to destination 50H in internal
memory
15) List down the assembly directives
Unit 2- CO2
1) Explain Software Development Tools chain (IDE)

2) Explain hardware Development Tools


3) Write short note on IDE (KEIL IDE)
4)Write short note on assembler, compiler
5)With the help of port structure explain why it is necessary to send
logic one on port pin before performing read operation.
6) With the help of port structure explain execution steps under read &
write operation
7).Explain Port structure of 8051
8) Explain mode0 & mode1 of timers in 8051
9) ) Explain 8-bit Auto Reload mode & Split Timer mode of timers in
8051
10) Calculate the values to be loaded into the TL and TH registers ,to
introduce delay of 1 ms ,Assume XTAL = 11.0592 MHz
11) Explain the use of following registers of 8051
a. TCON
B. TMOD
12) Draw and explain the Interrupt structure of 8051
13) With the help of IE and IP registers ,explain the interrupt structure of
8051
14) Write short note on Interrupt vector Table & interrupt service routine

15)Explain SCON register in detail .Write a program to display message


“YES” using serial communication concept.
16) With XTAL = 11.0592MHz, find the TH1 value needed to have the
following baud rates (a) 9600 (b) 1200 (c) 4800
17) Write a program for the 8051 to transfer letter “S” serially at 4800
baud, continuously.
Unit 3- CO3
1)Draw the interfacing diagram for LEDs connected to microcontroller
in common anode configuration and write a program to chase LEDs
from Left to Right.

2).List the difference between 8 bit interfacing mode and state their
advantages and disadvantages.

3)In 16x2 LCD, which of the following command is used to move the
cursor to the last line last column?
a. 0x89
b. 0xC0
c. 0x8F
d. 0xCF
4). Write a function list to initialize the LCD
5) Draw and explain interfacing of 16x2 LCD with 8051 microcontroller
in 8-bit mode and also write program to display word "PCCOE".

5) Explain detect and Key identification Logic in keypad


6) Explain Interfacing Techniques for stepper Motor
7) Write a program to rotate stepper Motor in clockwise direction with
45 &90 step angle
8) Write a program to rotate stepper Motor in anticlockwise direction
with 45 &90 step angle.
9) Write an ALP to rotate stepper motor 90 degree in the clockwise and
then anti-clockwise direction which is interfaced to 8051
microcontroller. with highest delay generated by Timer1 in Mode 1

10) Write a program in embedded C to toggle LEDs with a delay of


100ms when switch1 is pressed and blink the LEDs with a delay of
100ms when switch2 is pressed.
11) Write an program to display Hex counter on the LED
connected to port 2
12) Write an embedded c program to display “HELLO WORLD” on
16x2 LCD interfaced with 8051
13)list down Steps for Sending Command & Data to LCD
14) ) Write short notes on
I) Verification of Keypad
II) Key detection process
III) Key identification process

Unit 4- CO4
1What is the need of DAC in a microcontroller based systems?
2. Draw and explain DAC interfacing with 8051?
3) Write a program to generate a staircase waveform for 5 steps.
5) Draw and explain the block diagram of DAS system.
6) Draw and explain the block diagram of robot Control System
8) Draw &Explain PIC 18f4520 Micro controller architecture in detail
9)List down the features of PIC 18f4520 microcontroller
10) Draw &Explain PIC 18f4520 Micro controller pin diagram in
detail
11)Draw &Explain AVR Micro controller architecture in detail
9)List down the features of AVR microcontroller
10) Draw &Explain AVR Micro controller pin diagram in detail
11) Explain in detail the registers used to control the working of ADC
12) Draw and explain relay & Buzzer interfacing with 8051?
13) Write short note on Opto-isolator ?
14) List out difference between serial &parallel communication ?

You might also like