MSI Electronics (Kunshan) Co.

,Ltd

NB PCBA
REPAIRER
TRAINING
GUIDE
www.teknisi-indonesia.com
 Department of
RMA E.E.

Catalogue
Item Table Of Content Page

1 Introduction Of NB PCBA basic repair measure tools 2

2 Introduction Of Basic NB PCBA Repair Technique 3

3 Introduction Of NB PCBA Architecture 5

4 Introduction Of NB PCBA power sequence 7

5 Introduction Of NB PCBA repair process 8

6 NB PCBA repair share case 39

1. Introduction of NB PCBA Basic Measure tools

Multi-meter： Multi-meter is a useful tool for electronic industry,

it is used for measuring the most three important factors of circuit-Voltage、

Resistance and Current, therefore we called it“multi-meter”. Actually it is

also an electronic device with many functions. it can measure transistor、

reaction of inductor and value of Diode, so learning how to use it is very

important.

www.teknisi-indonesia.com
oscilloscope： In circuit, we must understand the action of frequency and
the reaction of waveform to find where is the problem and the precise

location. But using multi-meter to measure the action of waveform is not

accurate enough, especially in high frequency and fast reaction circuit,

that’s why we need oscilloscope to make measurement more accurate.

www.teknisi-indonesia.com
TL113 & TL309 Debug Card:
7-Segment LED display 16-decimal error post code, it can help you to find the

problem and solve it quickly。

TL113 TL309

2. Basic NB PCBA Repair Technique

Compare：When we are not sure this signal is regular, we can compare with another

good one to confirm it

Press：Use hand to press failure area, check bad connection of chip。

Touch：Touch component to check whether temperature is too high
Measure: Measure value of diode by multi-meter to check circuit is open or short

Besides the 4 basic ways we mention above, there’s more methods we use: exclude

possibility、replacement, etc. Generally speaking，we not only use one method,

but also use many methods at the same time. Especially when have used one method

but can not find the problem. We should have clear thinking for repairing. Repair

any block of circuit, first of all we should measure voltage、frequency and

phase.

if these three factors was satisfied, then check the block of BUS(ADDRESS BUS、

www.teknisi-indonesia.com
DATA BUS、CONTROL BUS)。As these six conditions were satisfied, it’s easily
to find out the problem.

Notice：When measure signal and voltage with power, prevent signal make short
with voltage, check signal accurately and make probe-stick vertical to M/B
test point, prevent m/b being made short by improper operation。

3. Introduction of NB PCBA Architecture

For the use of CPU, here are two main streams: INTEL and AMD. By study NB PCBA

architecture will save your time and work more efficiently.

3.1. INTEL Architecture

www.teknisi-indonesia.com
www.teknisi-indonesia.com
3.2. AMD Architecture

www.teknisi-indonesia.com
 4. Introduction of NB PCBA Power Sequence
NB PCBA power sequence will show you the relationship between voltage、clock

and phase position, it is a key point of notebook booting.

www.teknisi-indonesia.com
 5. Introduction of NB PCBA repair process
NO. Code Description Page

5.1 NBP01 No Power 8

5.2 NBP02 System Can't Power On 12

5.3 NBP06 No Display 18

5.4 NBL02 LCD Display Abnormally 20

5.5 NBB01 Battery Pack Can't Charge 23

5.6 NBK01 Keyboard Can't Work 24

5.7 NBI01 Internal L/R Speaker Fail 26

5.8 NBI05 USB Port Function Fail 28

5.9 NBI11 Card Reader Function Fail 30

5.10 NBI17 Earphone-Out Jack Function Fail 31

5.11 NBI21 RJ45 <Network> Jack Function Fail 33

5.12 NBH01 System Can't Detect HDD 35

www.teknisi-indonesia.com
5.1 NBP01 No Power
Method of repair
5.1.1 Check PCB board burned or damaged.

5.1.2 Check NBP01 (no power) issue in Troubleshooting Guide

5.1.3 Plug AC Adapter and measure PWR_SRC (19v) whether it’s regular. If

voltage is bounced, therefore the PCB has been made short.

5.1.4 Measure basic voltage (+3VALW, +5VALW) to make sure whether it’s regular

5.1.5 Measure KBC crystal (8M) and south bridge (ICH) 、crystal (32.768KHZ)

whether it’s regular and generate clock.

5.1.6 Check KBC data is lost or error

5.1.7 Measure SUS(3VSUS、5VSUS、2.5VSUS、1.2VSUS) voltage to make sure whether

it’s regular?

5.1.8 Trigger PWRSW and measure PWRBT-(3V) signal to make sure whether it’s

regular?

5.1.9 Measure PM_SLP_S3# (3V) signal to make sure whether it’s regular?

5.1.10 Measure RUN_ON (3V) signal to make sure whether it’s regular?

www.teknisi-indonesia.com
Repair Flowchart:

www.teknisi-indonesia.com
 NBP01(no power)

Y
Check co mponent Swap burned and damaged
burned or damaged component，if series then
announce material invalidated
N

Check NBP01 issue in Y

According to Troubleshooting
Troubleshooting guide Guide, change related component.
Guideolution 變更相關零件
N

N
Measure PWR_SRC is If voltage bounced show this circuits

regular? short.

Measure basic voltage N

If irregular, refer the related circuit
(+3VALW,+5VALW)
is regular?

Measure crystal (8M) N

If irregular, refer the related circuit
and (32.768KHZ) is
generate clock ?

Y
Check data error or Refresh KBC data
data lost in KBC

Measure SUS(3VSUS、 N
If irregular, refer the related circuit
5VSUS、2.5VSUS 、

www.teknisi-indonesia.com
1.2VSUS) voltage is ok?
 Y

N
Strobe PWRSW-and
If irregular, refer the related circuit
measure PWRBT-(3V)
signal is regular?

N
MeasurePM_SLP_S3#(3si If irregular, refer the related circuit
gnal is regular

Measure RUN_ON(3V) N
If irregular, refer the related circuit
signal is regular?

www.teknisi-indonesia.com
5.2 NBP02 System Can't Power On
5.2.1 NBP02 Debug Card display“FF”

Method of repair:
(1) check component on PCB board: burned or damaged?

(2) check NBP02 issue on Troubleshooting Guide

(3) follow these principle of voltage、frequency and phase to check voltage

of CPU、SB and NB if it’s regular.

(4) measure these signal in order: ALW、SUS、RUN、Vcore、CPU_RST，to down

sizing the area of bad signal

(5) check CPU_PWRGD，PCI_RST，CPU_RST to make sure whether it’s regular?

(6) check data is error or lost in bios?

(7) check every bus signal is regular? LPC_BUS、PCI_BUS、DMI_BUS。

(8) check the diode value under CPU socket(compare with good PCB board)。

Repair Flowchart:

www.teknisi-indonesia.com
 NBP02(system can not
power on)

Y
Check component is Swap burned and damaged
burned or damaged? component，if series then
announce material
N invalidated

Check NBP02 issue in Y

According to
Troubleshooting Guide
Troubleshooting Guide,
change related component.

N
Measure the voltage of If irregular, refer the related
CPU、NB、SB is regular? circuit

N
Measure ALW、SUS、
refer the related circuit and
RUN、Vcore、CPU_RST by
repair with power sequence
order is regular?

Check CPU_PWRGD， N
If irregular, refer the
PCI_RST，CPU_RST is
related circuit
regular?

Check BIOS data is error or Y

Update BIOS data
lost?

www.teknisi-indonesia.com
 Check these bus signal ： N
If irregular, refer the related
LPC_BUS、PCI_BUS、
circuit
DMI_BUS

Check the value of diode under CPU socket

(compare with good PCB)

5.2.2 NBP02 Debug Card display“D1/D2”

Method of repair：
(1) Insert Debug Card and display“D1/D2”it should be bios data error result

in “checksum can not pass”

(2) Refresh bios data and check if component is burned or damaged around bios

(3) Measure if LPC BUS signal and component around SB is short、open or component

broken

Repair Flowchart:

www.teknisi-indonesia.com
 NBP02(Debug Card display

D1/D2)

Refresh BIOS and check Y

Swap burned and damaged
component around bios
component，if series then
is burned or damaged?
announce material
invalidated
N

N
Measure connection of LPC
If irregular, refer to related circuit
BUS and component

around SB is regular?

5.2.3 NBP02 Debug Card display“D3/D4/D5”

Method of repair：
(1) Insert Debug Card and display“D3/D4/D5”stands for “memory not pass”

(2) check DIMM slot and component around DIMM slot is burned or damaged?

(3) check if memory is inserted accurately or test with the other memory

(4) measure VCC_DDR and 1.8VDIMM is regular?

(5) test with other version bios

(6) measure diode value of AD bus between NB and DIMM is regular?

Repair Flowchart:

www.teknisi-indonesia.com
 NBP02( Debug Card display
“D3/D4/D5”)

()

Memory not pass, check Y

) DIMM slot and Swap burned and damaged

component around DIMM component，if series then

slot is burned or damaged announce material

invalidated

N
Re-insert memory
Check memory is insert

accurate or change another

one
Y

N
If irregular, refer to related
Check voltage of VCC_DDR circuit
and 1.8VDIMM is ok

Test with another version of bios

Check diode value of AD bus N

If irregular, refer to related
between NB and DIMM is ok?
circuit

www.teknisi-indonesia.com
5.2.4 NBP02 Debug Card display“E0/E9/EA”

Method of repair：
(1) Insert Debug Card and display“E0/E9/EA”means trying to read data from

HDD, read the information of HDD directory

(2) most of the reason is bios data fail result to Debug Card display

“E0/E9/EA”；

(3) refresh BIOS data；

(4) Measure with memory circuit

Repair Flowchart:

NBP02(Debug Card

displayE0/E9/EA)

Because of bios data fail result in

Debug Card display“E0/E9/EA”

Y
If irregular, refer to related
Check component around
circuit
bios is burned or damaged

Swap burned and damaged

N component，if series then
Refresh BIOS data
announce material
invalidated

www.teknisi-indonesia.com
5.2.5 NBP02 Debug Card display“2A/2E”

Method of repair：
(1) Insert debug card and display“2A/2E”:can not detect graphic card

(2) check component around NB、Clock and graphic card BGA is burned or damaged

(3) Measure the working voltage of BGA and frequency of oscillator 27MKHz is

ok?

(4) Check PCI_E BUS signal between NB and graphic card is ok?

Repair Flowchart:

www.teknisi-indonesia.com
 NBP02(Debug Card

display2A/2E)

Insert debug card and display

“2A/2E”, can not detect graphic

card

Swap burned and damaged

component，if series then
announce material
check component around Y
invalidated
NB、Clock and BGA is ok?

N
Check work voltage of BGA If irregular, refer to related
and frequency circuit

If irregular, refer to related

Check PCI_E between NB N
circuit
and graphic card

5.3 NBP06 No Display

Method of repair：
5.3.1 Check component on PCB is burned or damaged

5.3.2 Check NBP06 issue in Troubleshooting Guide

5.3.3 Check voltage of graphic card (1.2v) or (1.8v) is regular and crystal

(27M)is working;

www.teknisi-indonesia.com
5.3.4 Check diode value between VGA connector and graphic card chip is ok
5.3.5 Check diode value of bus between SB and graphic card is ok

5.3.6 Check bios data is correct

Repair Flowchart:

www.teknisi-indonesia.com
 NBP06 (no display)

Check component on PCB Y

Swap burned and damaged
is burned or damaged component，if series then
announce material

N invalidated

Check NBP06 issue in Y

According to Troubleshooting
Troubleshooting Guide
Guide, change related component.

Check (1.2v) or (1.8v) N

If irregular, refer to related
on graphic card and
circuit
crystal (27M)

Check diode value N

If irregular, refer to related
between graphic ic and
circuit
VGA connector

Check diode value N

If irregular, refer to related
between NB and
circuit
graphic card

Check bios data is correct

www.teknisi-indonesia.com
5.4 NBL02 LCD Display Abnormally
Method of repair:
5.4.1 Check component on PCB is burned or damaged?

5.4.2 Check LCD connector is regular

5.4.3 Check NBL02 issue on Troubleshooting Guide

5.4.4 Check voltage、frequency on graphic card is ok?

5.4.5 Check voltage of LCD connector

5.4.6 Check diode value between graphic card and LCD connector

Repair Flowchart:

www.teknisi-indonesia.com
 NBL02(LCD display abnormal)

Check component on Y
Swap burned and damaged
PCB is good? component，if series then
announce material

N invalidated

Y
Check LCD connector
Swap bad connector

Check NBL02 issue on N

According to Troubleshooting
Troubleshooting Guide
Guide, change related
component.

N
Check voltage of graphic
If irregular, refer to related
card and frequency is ok
circuit

N
Check voltage of LCD If irregular, refer to related
connector transistor circuit

N
Check diode value If irregular, refer to related
between LCD circuit
connector and graphic

card

www.teknisi-indonesia.com
5.5 NBB01 Battery Pack Can't Charge：
5.5.1 Check component around battery connector on PCB is burned or damaged

5.5.2 Check NBB01 issue on Troubleshooting Guide

5.5.3 Check diode value of battery connector

5.5.4 plug in AC Adapter and battery，measure voltage and phase between

MAX1772 chip and inductor

5.5.5 Check version of KBC

Repair Flowchart:

www.teknisi-indonesia.com
 NBB01(can not charge)

Check component Y

around battery Swap burned and damaged

connector component，if series then

announce material
invalidated
N

Check NBB01 issue on Y

According to Troubleshooting Guide,
Troubleshooting Guide
change related component.
Guide

Measure diode value of N

If irregular, refer to related r
battery connector is
circuit
regular

Plug in battery and AC， N

If irregular, refer to chip
measure voltage between
1772 circuit
chip 1772 and inductor

Check version of KBC Y

Refresh KBC

www.teknisi-indonesia.com
5.6 NBK01 Keyboard Can't Work：
5.6.1 Check component around keyboard connector is burned or damaged?

5.6.2 Check NBk01 issue on Troubleshooting Guide

5.6.3 Check version of KBC

5.6.4 Measure diode value of keyboard

5.6.5 Check voltage of keyboard connector

5.6.6 check EC_KBRST#、KB_SCI#、KB_SMI# and K/B Connector DATA BUS signal

is ok

Repair Flowchart:

www.teknisi-indonesia.com
 NBK01(k/b not working)

Check component Y

around k/b connector Swap burned and damaged

component，if series then
announce material
invalidated
N

Check NBK01 issue in Y

According to Troubleshooting Guide,
Troubleshooting Guide
change related component.

Y
Check version of KBC Refresh KBC data

Check diode value of N

If irregular, refer to KBC
k/b connector
circuit

Check K/B Connector N

If irregular, refer to
DATA BUS signal
related circuit

www.teknisi-indonesia.com
5.7 NBI01 Internal L/R Speaker Fail
Method of repair：
5.7.1 Check component around audio chip

5.7.2 Check NBI01 issue by Troubleshooting Guide

5.7.3 Check bios data and audio driver

5.7.4 measure voltage、frequency of audio chip and amplifier

5.7.5 Check diode value between amplifier and audio connector

5.7.6 Check voltage and waveform of speaker jack connect with capacity

Repair Flowchart:

www.teknisi-indonesia.com
 NBI01 (internal R/L audio fail)

Y Swap burned and damaged

Check component
component，if series then
around amplifier
announce material invalidated

Check NBI01 issue by Y

According to Troubleshooting Guide,
Troubleshooting Guide
change related component.

N
Check bios data and Update bios and install audio
audio driver driver

N
Check voltage of
If irregular, refer to related
audio chip is regular
circuit

Check diode value of N

If irregular, refer to related
audio connector
circuit

check voltage of audio N If irregular, refer to related

jack and waveform circuit

www.teknisi-indonesia.com
5.8 NBI05 USB Port Function Fail
Method of repair：
5.8.1 Check component around USB Connector

5.8.2 Check NBI05 issue by Troubleshooting Guide

5.8.3 Check connection of USB Connector with VCC(5V) and GND

5.8.4 Check diode value of USB Connector

5.8.5 Check SB generate frequency (48M) to USB

Repair Flowchart:

www.teknisi-indonesia.com
 NBI05(USB port fail)

Check component around Y

USB Connector Swap burned and damaged

component，if series then
announce material invalidated

Check NBI05 issue by Y

According to Troubleshooting Guide,
Troubleshooting
change related component.
Guide

Check VCC(5V) and N

If irregular, refer to related
GND of USB connector
circuit

Check diode value of N

If irregular, refer to R、L and
USB connector
inductor circuit

Check frequency 48M N

If irregular, refer to related circuit
（clock No. 15pin）

between USB and SB

www.teknisi-indonesia.com
5.9 NBI11 Card Reader Function Fail
Method of repair：
5.9.1 Check component around card reader

5.9.2 Check NBI11 issue by Troubleshooting Guide

5.9.3 measure V3S.V5S, PCI_RST# and CB_48M from CLOCK

5.9.4 check diode value of card reader

5.9.5 measure diode value between card reader chip and SB PCI BUS

Repair Flowchart:

www.teknisi-indonesia.com
 NBI11(card reader fail)

Check component around Y

card reader Swap burned and damaged

component，if series then announce
material invalidated

Check NBI11 issue by Y

According to Troubleshooting
Troubleshooting
Guide, change related component.
Guide

Check V3S.V5S, PCI_RST#

N
signal and CB_48M from If irregular, refer to related circuit
CLOCK

Measure diode value of card N

If irregular, refer to related
reader
circuit

Check diode value between N

If irregular, refer to related
card reader chip and SB
circuit
PCI BUS

www.teknisi-indonesia.com
5.10 NBI17 Earphone-Out Jack Function Fail
Method of repair：
5.10.1 check component around earphone-out jack

5.10.2 check NBI17 issue in Troubleshooting Guide

5.10.3 check BIOS data and driver；

5.10.4 measure voltage: +V5_AUDIO、+V3_AUDIO and crystal (24M)

5.10.5 check diode value between AUDIO chip and LINEIN_R ,LINEIN_L signal

5.10.6 check signal between AUDIO chip to SB

Repair Flowchart:

www.teknisi-indonesia.com
 NBI17(earphone-out jack fail

Swap burned and damaged

component，if series then
announce material invalidated
Check component around Y
earphone-out jack

Check NBI17 issue by Y

According to Troubleshooting
Troubleshooting Guide
Guide, change related component.

N
Check BIOS data and drivers Re-install drivers or refresh bios

Measure +V5_AUDIO， N
If irregular, refer to related circuit
+V3AUDIO and crystal

(24M)

Check signal LINEIN_R , N

If irregular, refer to related
LINEIN_L
circuit

N
Check signal between AUDIO If irregular, refer to related
chip to SB circuit

www.teknisi-indonesia.com
5.11 NBI21 RJ45 <Network> Jack Function Fail
Method of repair：
5.11.1 check component around network connector and network chip is burned

or damaged

5.11.2 Check NBI21 issue in Troubleshooting Guide

5.11.3 Measure voltage of network chip: VCC(3.3V)，clock (25M)，network

connector、network inductor and diode value of network chip

5.11.4 check signal LAN_RST# is regular?

5.11.5 check signal PCIE BUS between network chip and SB is regular?

Repair Flowchart:

www.teknisi-indonesia.com
 NBI21 (RJ45 function fail)

Check component around Y

Swap burned and damaged
network chip and
component，if serious then
connector
announce material invalidated

Check NBI21 issue in Y According to Troubleshooting Guide,

Troubleshooting Guide change related component.

check voltage of network

N
chip 、network inductor、 If irregular, refer to related
network connector and diode circuit
value of network chip

Check signal LAN_RST# (pin N If irregular, refer to related circuit

20)

Check signal PCIE BUS N

If irregular, refer to related
between network chip and SB
circuit

www.teknisi-indonesia.com
5.12 NBH01 System Can't Detect HDD
Method of repair：
5.12.1 Check component around HDD connector is burned or damaged?

5.12.2 Check NBH01 issue in Troubleshooting Guide

5.12.3 Check working voltage of HDD +5VRUN and GND is regular?

5.12.4 Check signal IDE1_RST# is regular?

5.12.5 Check signal INT_IRQ14 and other control signals are ok?

5.12.6 Check signal HDD DATA BUS between HDD connector to SB

Repair Flowchart:

www.teknisi-indonesia.com
 NBH01( system can not detect HDD)

Swap burned and damaged

Y
check component around HDD component，if serious then
)
connector announce material invalidated

Y
Check NBH01 issue in According to Troubleshooting Guide,
Troubleshooting Guide change related component.

N
Check voltage of HDD If irregular, refer to _5V RUN
+5VRUN and GND is ok circuit

N
Check IDE1_RST# If irregular, refer to IDE1_RST
circuit

Check signal N
If irregular, refer to related
INT_IRQ14 and related
circuit
circuit

Check HDD DATA BUS N

If irregular, refer to related
between network chip and
circuit
network connector

www.teknisi-indonesia.com
 6. PCBA repair case
6.1 repair case share
NO. Code Description Page
6.1.1 NBI01 MS-10581 Internal L/R Speaker Fail 40
6.1.2 NBP02 MS-10321 System Can't Power On 43
6.1.3 NBP01 MS-10341 NO Power 46
6.1.4 NBP02 MS-10341 System Can't Power On 50
6.1.5 MS-14121 New Card Function Fail 54
6.1.6 NBP01 MS-10341 No Power 57
6.1.7 NBP01 MS-10571 No Power 60
6.1.8 NBP06 MS-10341 No Display 63
6.1.9 NBP02 MS-10571 System Can't Power On 66
6.1.10 NBP06 MS-16331 No Display
6.1.11 NBP02 MS-163A1 System Can't Power On
6.1.12 NBL02 MS-14141 LCD Display Abnormally

www.teknisi-indonesia.com
6.1.1 NBI01 Internal L/R Speaker Fail
1. Model No.： 607-10581－070

2. problem： NBI01（internal speaker fail）

3. process： (Refer to circuit：MS-10581 Version. A20)

3-1.check appearance、check troubleshooting Guide and Update Bios

3-2. play audio file in WINDOWS and use oscilloscope to measure

chip U23 PIN14(SPKˍOUT－R+) and PIN18(SPKˍOUT－R－), the output

signal is 2.5v high level “non-waveform”, but should be high level

2.5v “waveform”。

High level 2.5v waveform 2.5v high level

non-waveform

These two signals should be

2.5v high level waveform

3-3.measure input voltage of U23，get AVDO_5V 5V is regular ，but

pin 17 no signal detect.

3-4.measure signal between C536 to ALC883 LINE-R is regular。

www.teknisi-indonesia.com
3-5.the problem should be located at C536 or U23，so we swap C536
 component，test with internal speaker ok!

4.Summary ：because of C536 damaged ,result in U23 can not detect

signal，so no audio signal generation ,then internal L/R

speaker fail。

5. Repair Flowchart:

www.teknisi-indonesia.com
 NBI01 (internal R/L speaker fail)

Swap burned and damaged

component，if series then
Y
Check component around announce material invalidated

audio chip

Check NBI01 issue in Y According to Troubleshooting

Troubleshooting Guide Guide, change related

component.

N
Check bios and driver Update bios or install driver

N
Measure diode value of If irregular, refer to related
audio jack is regular circuit

Check SPKˍOUT－R+ and

N
SPKˍOUT－R－ signal， If irregular, refer to related
should be 2.5V hi-level circuit
waveform (actually we got 2.5V
non-waveformform)

Check pin 17 of u23 no signal N

found but C536 the other side If irregular, refer to related

signal LINE－R is regular circuit

Swap C536 ,pin17 of u23

www.teknisi-indonesia.com
signal ok, audio working
6.1.2 NBP02 System Can't Power On
1 Model No.： 10321

2 Problem：NBP02

3 Process： (Refer to MS-10321 Version 1.0)

3-1 This m/b no boot and display “FF”，check voltage ，no problem

found; and measure the three key factors of booting: voltage、

frequency and phase，no problem found ;check every voltage and

signal in detail to find any different，compare to voltage

sequence，we found it irregular in PIN4 of U29 with another side

of 4 Resistors。

3-2 measure input signal of U29，PIN 1 and 2 PLTRST_ signal is 3V high。

3-3 then check pin 5, 3VSUS voltage ok。PIN 4 connect to IDE1-RST_

NB_RST_ PCIEˍRSTˍ and NBˍLANˍRSTˍ signal，those signals

are connected with R320，R331，R328 and R324。It should be 3V high，

www.teknisi-indonesia.com
but this signal that connect to another side is under 3v ，output
 of pin4 of U29 is regular
Abnormal signal is
under 3v

Normal signal
is hi-3v

4-4 we have doubt about the input signal and remove those 4 Resistors

by sequence。When remove R320，R331，R328，R324, the signal should

be 3v。therefore, we found signal IDE1ˍRSTˍ is irregular。

4-5 remove R320 and measure both side of R320 by multi-meter，IDE_RST

made a short with GND。This signal connect to HDD connector (con13)

by R206。

4-6 Measure value of R206 is 47ohm，exclude this possibility，it should

be mechanic issue ，so remove CON13，and connect to AC Power，

m/b power on ok!

5. Summary: CON13 connector fail result in IDEˍRSTˍ signal

abnormal，M/B no boot。

www.teknisi-indonesia.com
6 Repair Flowchart：
 NBP02 (system can not power on)

Swap burned and damaged

component，if series then
Y
Check component is announce material

burned or damaged invalidated

Y
According to
Check NBP02 issue in
Troubleshooting Guide,
Troubleshooting Guide
change related component.
N

N
If irregular, refer to related
Check voltage of CPU、
circuit
SB、NB

N
check ALW、SUS、RUN、 If irregular, refer to power
Vcore sequence circuit

found PCIE_RST-(pin4 of u29)

signal is under 3v (it should be 3v

hi-level)

Found IDE1_RST_ fail cause

PCIE_RST-signal fail

Find PCIE_RST signal connect to

HDD con13

Swap con13 connector then

IDE1_RST_，PCIE_RST-signal is
regular, m/b power on

www.teknisi-indonesia.com
6.1.3 NBP01 No Power
1 Model No.： 10341

2 problem： NBP01

3 process ：(Refer to MS-10341 Version 0.A)

3-1 check appearance of component and VCC、GND not make short。

Measure voltage According to power sequence，the main

reason of no boot is 3V，5VRUN not working

3-2 check signal and voltage before 3V、5VRUN。When check pin2

of MAX1999，problem found with +3SUSPWROK。

4-3 In this case the signal is high level (3V)。Now is low level，

three components connected to with +3SUSPWROK，one is MAX1999

chip，another one is KBC chip，the other is Q12。Now we have

to make sure the problem is no signal or pulled down by the

other signal。So disconnect this signal and the other

www.teknisi-indonesia.com
component。
 4-4 There’s the same problem when disconnect Q12. Re-disconnect

KBC27PIN and R185, measure pin2 of MAX1999 again is regular.

Therefore, the problem is located in KBC or R185.

4-5 First take off the value of R185, it should be 0 ohm. But we

got the value of R185 is infinite, therefore swap R185 and

trigger again, trouble shooting.

5. Summary：Because of R185 defect result in +3VSUS POWER_OK is

irregular.

6 Repair Flowchart：

www.teknisi-indonesia.com
 NBP01( no power)

Swap burned and damaged

component，if series then
Y
Check appearance announce material invalidated
of component

Y According to Troubleshooting
check NBP01 by
Guide, change related component.
Troubleshooting

Check PW R_SRC N
If voltage bounced, it made short
(19v)

N
Check voltage
If irregular, refer to related circuit
(+3VALW,+5VALW)

Check crystal (8M) and N

If irregular, refer to related circuit
(32.768KHZ) is regular

Y
Check KBC lost or error Refresh KBC DATA

Measure SUS(3VSUS、 N
If irregular, refer to related circuit
5VSUS、2.5VSUS、

www.teknisi-indonesia.com
1.2VSUS) is regular
 Y

Check PM_SLP_S3#(3V) N
If irregular, refer to related circuit
Signal is regular

Measure +3SUSPWROK is low level (3v high level is

normal)

Check related circuit (pin2 of max1999、Q12、R185) find resistance

of R185 is irregula r and limitless (0 ohm is normal)

Swap R185 and n/b power on ok

www.teknisi-indonesia.com
6.1.4 NBP02 System Can't Power On
1 Model No.：10341

2 problem： NBP02

3 Process： (Refer to MS-10341 Version 0.A)

3-1 this M/B display error code“FF”, measure voltage of CPU but

no voltage found and also no being made short. Therefore fix

to mount all equipment and measure CPU voltage control chip

PU6.Two main reasons for CPU without voltage, one is voltage

chip not working; the other one is voltage that pulled down

by other reason.

4-2 First of all, we take first consideration to focus on in/output

of CPU voltage, firstly measure signal of PIN20、PWR－SRC、

＋5VRUN of PIN22、＋3VRUN of PIN48 ,they are regular.

www.teknisi-indonesia.com
 4-3 check signal SYS－PG、VR－ON ok. Signals are also regular from

CPU－VID0 to CPU－VID6.

www.teknisi-indonesia.com
 4-4 When check PIN12、13 of PU6 and find voltage irregular

(0v)(normal is 0.5v)

4-5 therefore remove all equipments and take the diode value of this

BUS, find resistance of PR116 limitless, regular is 2K. therefore

judge PR116 defect, trigger again after changed, pin12、13 of PU6

generate voltage 0.5V. Mount all equipments and power on, booting.

5. Summary：Because of resistor PR116 defect result in CPU have no

voltage, no booting.

6 Repair Flowchart：

www.teknisi-indonesia.com
 NBP02( no power )

Y Swap burned and damaged

Check component
component，if series then
appearance
announce material
invalidated
N

Y
Check NBP02 issue in

Troubleshooting Guide According to Troubleshooting

Guide, change related
component.

Check CPU voltage is irregular

(0v) (should be 1v)

Measure CPU voltage PU6 PWR－

SRC.+5vRUN.+3vRUN.SYS_PG.V

R_ON.CPU_VID0~CPU_VID6 are
all regular

Find voltage of PU6 12 and PIN13

Are irregular (0v) (should be 0.5v)

Measure value of pin12 that

connect to PR116 is limitless

(2k is normal)

Swap PR116, voltage of CPU is

regular, power on

www.teknisi-indonesia.com
 6.1.5 New Card Function Fail
1 Model No.： 14121

2 problem： NB (NEW card function fail)

3 Process： (Refer to MS-14121 Version 1.1)

4-1 the m/b can not detect new card，check appearance ok。Test with

all equipments and measure every pin of new card slot CNT8. first

take three voltage：＋3RUNˍPCIE，＋3VSUSˍPCIE，＋1.5VPCIE

ˍCARD, no problem found.

4-2 measure pin25，24，22，21 of new card slot: PCIEˍTXPO，PCIE

ˍTXNO，PCIEˍRXPO，PCIEˍRXNO are regular. Those signals are

communicate by NB. That’s proving no problem between NB to

slot.

4-3 check CLKˍNEWˍCARDˍ is irregular. This signal have no

voltage and waveform form (0.5v is normal)。

4-4 track this signal to CLKT5, check signal of PIN13 CLKˍNEW

ˍCARD is regular.

www.teknisi-indonesia.com
 signal transit to slot by pass three component RT163，R880、CI864.

4-5 check RT163, have the same result with another side of CLKT5,the

other side no signal found.

4-6 Therefore the problem located in R880、CI864 and RT163. remove

all equipment and measure resistance of RT163. remove RT163 but

regular, so can exclude RT163 and check diode value from another

side of RT163, resistance is 300 more than average value 75,

now the problem locate in R880、CI864。

4-7 resistance is 400s when measure R880, more than average value

www.teknisi-indonesia.com
50, remove R880 and solder on RT163 check again, diode value
 is regular, therefore swap R880 and fix all equipment and

booting, problem shooting.

5. Summary：Because of R880 defect result in new card can not

detect.

6 Process：

www.teknisi-indonesia.com
 (New card function fail)

Check connector of new card Y

and component appearance Swap burned and damaged

component，if series then announce
material invalidated

Update related issue by Y

According to Troubleshooting
Troubleshooting Guide Guide, change related component.

Measure voltage of new card：

N
＋3RUNˍPCIE，＋3VSUSˍ If irregular, refer to related circuit
PCIE，＋1.5VPCIEˍCARD

whether or not regular

Measure connector of New Card , CLK

ˍNEWˍCARDˍ have no voltage

and waveform (0.5v is regular)

Measure related circuit of R880, get

resistance 400 ohm (50 ohm is

normal)

Swap resistor R880 ok, resistance is 50

ohm, trouble shooting

www.teknisi-indonesia.com
6.1.6 NBP01 No Power
1. Model No.： 607-10341-030

2. problem： NBP01（no power）

3. Process： (Refer to：MS-10341-220)

3-1 check appearance、check Troubleshooting Guide and Update Bios.

3-2 because of no power, V_RUN is necessary for power on, but no

+3VRUN and +5VRUN found. Measure by power sequence, check VAC_OK#

before VRUN but not found. Signal AC_OK＃ generated from MAX1772,

have the same problem by swap MAX1772.

4-3 when measure PWR_SW that we find it close to 2V low (normal is

3v). We find PWR_SW# is pass negative of D3 by check circuit.

measure diode value of D3,R1,C4. We find the values of both side

of C4 are the same, troubleshooting by swap C4.

www.teknisi-indonesia.com
5. Summary：Because of C4 defect result in PWR_SW# close to low. PCB

no power.。

6 Process：

www.teknisi-indonesia.com
 NBP01（no power）
Y

Y Swap burned and damaged

Check appearance of
component，if series then
component
announce material invalidated

Y
Check NBP01 issue
According to Troubleshooting
in Troubleshooting
Guide, change related component.
Guide

N
Check PW R_SRC (19v) is
If voltage bounced, it indicate circuit make
regular
short

Check voltage +3VRUN. +5VRUN

are not regular

Check signal AC_OK# is

regular.

Measure PWR_SW# is 2v,

not regular. (3V is normal)

Check value of diode of C4

is regular?

PWR_SW become irregular if swap

component, PCB power on

www.teknisi-indonesia.com
6.1.7 NBP01 No Power
1. Model No.： 607-1057-010

2. problem： NBP01（no power）

3. Process： (Refer to：MS-1057-0B)

4-1.check appearance, check Troubleshooting Guide and Update Bios.

4-2.ecause of no power, measure 19V is regular, but 3VALW pull down

from 3V to 1V。

4-3.because of voltage 3VALW is generate by PU7. measure voltage

of PU7, we found voltage of PWR_SRC changed from 19V to 3V，

19v connect with PU7 by PR136.check resistance of PR136 we got

200 ohm (4.7 ohm is normal)。Trouble shooting by swap PR136.

5. Summary：Because of PR136 defect result in PWR_SRC no power.

www.teknisi-indonesia.com
6 Process：
 NBP01（no power）

Y
Check appearance of Swap burned and damaged
component component，if series then
announce material invalidated
N

Check NBP01 by Y
According to Troubleshooting
Troubleshooting guide
Guide, change related component.

Check PWR_SRC (19v) is N

If voltage bounced, it indicate circuit make
regular
short

Check voltage of +3VALW is 1V(3V

is normal)

Check input voltage of PU7 is

19v (3v is irregular)

19V connect with PU7 by

PR136, resistance of PR136 is

200 ohm (4.7 is regular)

+3VALW is regular by swap PR136.

www.teknisi-indonesia.com
6.1.8 NBP06 No Display
1. Model No.： 607-1034-030

2. problem： NBP06（CRT no display）

3. Process： (Refer to：MS-10341-220)

3-1 check appearance、 check Troubleshooting Guide and Update Bios.

3-2 Signal VGA_HSYNC, VGA_VSYNC have been generate, but voltage of

VGA_VSYN is pull down by 2v (3v is regular). Check circuit, find

some thing to do with R273. measure resistance of R273 is

limitless, swap R273 。

4-3.measure pin2 of U18, find value of diode reach limitless, swap

U18, problem troubleshooting.

www.teknisi-indonesia.com
5 Summary：Because of U18 defect result in signal VGA_VSYNC is unstable,

LCD no display.

6 Process：

www.teknisi-indonesia.com
 NBP06 (No display)

Check appearance of Y
Swap burned and damaged
component component，if series then
announce material invalidated

Check NBP 06 Y According to Troubleshooting

Troubleshooting Guide Guide, change related

component.

Check signal of VGA_VSYNC

is 2V (3v is regular)

Check circuit，find signal

VGA_VSYNC connect to R273,

measure it we found value limitless

(normal is 33 ohm)

Swap R273, VGA_VSYNC irregular,

too. Then check pin2 of U18, diode

value irregular

Swap U18，signal of VGA_VSYNC is

regular. CRT display normal

www.teknisi-indonesia.com
6.1.9 NBP02 System Can't Power On
1. Model No.： MS-1057

2. problem： NBP02（system can’t power on FF）

3. Process： (Refer to：MS-1057-0B)

4-1.check appearance、check Troubleshooting Guide and Update Bios

4-2.because of FF，signal RST# can not be detect. And voltage of CPU

not generates, but VTT is regular.

4-3 Continue measure VTT_PWRGD but not generate, signal VTT_PWRGD

generated by PU4, trouble shooting by swap PU4.

5. Summary：Because of PU4 defect, result in VTT_PWRGD not generate,

6 Process：

www.teknisi-indonesia.com
 NBP02 (system can not

power on)

Check appearance of Swap burned and damaged

component，if series then
component.
announce material invalidated
N

Y
Check NBP02 issue by
According to
Troubleshooting Guide.
Troubleshooting Guide,
change related component.

Measure signal RST#, no

CPU voltage found

Check VTT_PWRGD not

generates.

Swap signal output chip

PU4 of VTT_PWRGD

Signal output of VTT_PWRGD

is regular then system power on

Uu7yy

6.1.10 NBP06 No Display

1. Model No.： 607-16331-B10

2. problem： NBP06（CRT no display）

3. Process： (Refer to：MS-16331-0B)

www.teknisi-indonesia.com
4-1 check appearance、check Troubleshooting Guide and Update Bios.
 4-2.measure diode value of PCI-E bus between NB and Graphic card,

find diode value of C410 connect to NB_TXP0 is limitless

(277 is regular)。

4-3 press NB then diode value of U018 NB_TXP0 become regular. So we

determine NB un-solder。

4-4 Swap NB then diode value of NB_TXP0 become regular, CRT display

normal

5. Summary：Because of NB un-solder result in signal NB_TXP0 not

generate to U21.

6 Process：

www.teknisi-indonesia.com
 NBP06(no display

Check appearance of Y
Swap burned and damaged
PCB component，if series then
announce material invalidated

Check NBP06 issue in Y

According to Troubleshooting
Troubleshooting Guide
Guide, change related
component.

Check voltage of GPU N

If irregular, refer to related
(1.2v)、(1.8v) and crystal
circuit
(27M) is regular?

Measure diode value of N

If irregular, refer to related
VGA connector is
circuit
regular?

Measure diode value of PCI-E BUS is limitless

Signal NB_TXP0 become regular after

swap NB, display normal

www.teknisi-indonesia.com
6.1.11 NBP02 System Can't Power On
1. Model No.： 607-163A1-B10

2. problem： NBP02（no boot and no display,”38”）

3. Process： (Refer to：MS-163A1-0A)

4-1 this PCB display “38”when mount all equipments. Exclude all

possibility, we find it can not display when plug LCD.

4-2 check appearance、check Troubleshooting Guide and Update Bios

4-3 find voltage of LCD connector PIN1 and PIN2 (＋3V_LCD) is

irregular and related to Q4.Q7.

4-4.check voltage S of Q4 is regular, but voltage D is irregular.

Find component C18、C21 and Q7 are working regular by compare other

PCB. +3v_LCD become regular by swap Q4, plug on LCD booting, all

pass.

5. Summary：Because of Q4 defect result in +3V_LCD irregular, no

www.teknisi-indonesia.com
display “38”
6 Process：

NBP02 (system can power on)

Y
Swap burned and damaged
Check appearance of component，if series then announce
component material invalidated

Check NBP02 in Y According to Troubleshooting

Troubleshooting Guide.
Guide, change related
component.

Check voltage of LCD connector,

found voltage 3V_LCD is irregular

Voltage D of Q4 irregular, +3V_LCD

become regular by swap Q4, booting

with LCD

www.teknisi-indonesia.com
6.1.12 NBL02 LCD Display Abnormally
1. Model No.： 607-14141

2. problem： NBL02（LCD no display）

3. Process： (Refer to：MS-14141-0A)

4-1.check appearance then find pin10 and pin11 of CONT are connected

together but short.

4-2.those are +3V_LCD and +3VRUN of pin10 and pin11

4-3.find LCD become dark after swap CONT1, but CRT display regular.

4-4 measure voltage of +3V_LCD and +3VRUN less than average voltage

by 1V

4-5.Q4、Q3、Q1、+3V_LCD and 3VRUN are connected together, find D value

of Q4 is irregular (300 is regular, and this PCB make short with

GND) diode value become regular by swap Q4.

www.teknisi-indonesia.com
4-6 measure Pin1 of CONT1 is close to low, become regular by swap L29,
LCD display normal.

5. Summary：Because of CONT1, Q4、L29 short defect ,result in LCD

no display.

6 Process：

www.teknisi-indonesia.com
 NBL02 (LCD no display)

Swap burned and damaged

Check appearance of Y
component，if series then
PCB is burned or
announce material
damaged
invalidated
N

Check LCD connector found

PIN 10 and PIN11 make short

Measure +3V_LCD and

+3VRUN are close to low by

1V

Find diode value of Q4 is

irregular (regular is 300 and

make short with GND) swap Q4

is regular

Find PIN1 of CONT1 voltage

is close to low

Voltage become regular by

swap L29, LCD display ok

6.1.13 NBB01 Battery Pack Can't Charge

1. Model No.： 607-12211

www.teknisi-indonesia.com
2. problem： NBB01（battery can not charge）
3. Process： (Ref：MS-12211-0D)

4-1 battery pack recharge fail, check component around battery

connector and chip 1772 is burned or damaged?

4-2 check the circuit related battery recharge function, plug on

battery and AC power and use oscilloscope to measure the other

side of PL11 but only voltage no waveform (it should have

waveform on this side and the other side should have voltage)

4-3.measure voltage pin18、19 of chip 1772 is irregular. output of

18、19PIN are connect to CSIP SCIN, by PR112、PR113 and transit

signal to PL11。

4-4.remove equipments and measure resistor, find resistance of

PR112 is close to high (regular values is 1 ohm), therefore swap

www.teknisi-indonesia.com
PR112 than resistance become regular. Measure voltage and
 waveform of PL11 are regular

4-5.recharge test with battery ok

5 Summary：Because of PR112 defect, result in battery can not recharge.

6 Process：

www.teknisi-indonesia.com
 NBB01 (battery can not

charge)

Check component Y
Swap component, if serious
around battery
announce material invalidated
connector

Y
Change component by
Check NBB01 solution
Troubleshooting Guide
in Troubleshooting

Guide

Plug on battery and AC，measure

voltage and waveform of chip 1772

is regular.

Check pin 18, 19 of chip 1772 ,

find two signal CSIP SCIN are

irregular

Remove all equipments and measure resistance of PR112,

find resistance is close to high (regular is 1 ohm)

Swap PR112 than resistance 、

waveform and voltage become

regular, battery recharge test ok.

www.teknisi-indonesia.com