Scribd
Upload
11 views

ASK Code:-: All All

This document presents code for amplitude shift keying (ASK) modulation and demodulation. It defines binary information as input and uses loops to represent it as a digital signal. It then modulates a carrier signal by varying the amplitude based on the binary values. Demodulation is done by multiplying with the carrier, integrating, and thresholding to recover the binary values. Plots are shown for the transmitted signal, modulated signal, and demodulated output.

Uploaded by

Omkar Patil
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
11 views

ASK Code:-: All All

This document presents code for amplitude shift keying (ASK) modulation and demodulation. It defines binary information as input and uses loops to represent it as a digital signal. It then modulates a carrier signal by varying the amplitude based on the binary values. Demodulation is done by multiplying with the carrier, integrating, and thresholding to recover the binary values. Plots are shown for the transmitted signal, modulated signal, and demodulated output.

Uploaded by

Omkar Patil
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

ASK

Code:-
clc; clear all; close all;

x=[1 0 0 1 1 0 1]; % Binary Information


bp=0.000001; % bit period
disp('Binary information at Transmitter :');
disp(x);

%% representation of transmitting binary information as digital signal


bit=[];
for n=1:1:length(x)
if x(n)==1
se=ones(1,100);
elseif x(n)==0
se=zeros(1,100);
end
bit=[bit se];
end

t1=bp/100:bp/100:100*length(x)*(bp/100);
subplot(3,1,1);
plot(t1,bit,'r','linewidth',2.5);
grid on;
axis([0 bp*length(x) -.5 1.5]);
ylabel('amplitude(volt)');
xlabel('time(sec)');
title('transmitting information as digital signal');

%% ASK modulation
A1=10; % Amplitude of carrier signal for information 1
A2=0; % Amplitude of carrier signal for information 0
br=1/bp; % bit rate
f=br*10; % carrier frequency
t2=bp/99:bp/99:bp;
ss=length(t2);
m=[];
for i=1:1:length(x)
if x(i)==1
y=A1*cos(2*pi*f*t2);
else
y=A2*cos(2*pi*f*t2);
end
m=[m y];
end
t3=bp/99:bp/99:bp*length(x);
subplot(3,1,2);
plot(t3,m,'b','linewidth',2.5);
xlabel('time(sec)');
ylabel('amplitude(volt)');
title('ASK modulated waveform');

%% ASK demodulation
mn=[];
for n=ss:ss:length(m)
t=bp/99:bp/99:bp;
y=cos(2*pi*f*t); % carrier signal
mm=y.*m((n-(ss-1)):n);
t4=bp/99:bp/99:bp;
z=trapz(t4,mm); % integration
zz=round((2*z/bp));
if(zz>5) % logic level = (A1+A2)/2=5
a=1;
else
a=0;
end
mn=[mn a];
end
disp('Binary information at Receiver :');
disp(mn);

%% Representation of binary information as digital signal which achieved after ASK


demodulation
bit=[];
for n=1:length(mn)
if mn(n)==1
se=ones(1,100);
else
se=zeros(1,100);
end
bit=[bit se];
end
t4=bp/100:bp/100:100*length(mn)*(bp/100);
subplot(3,1,3)
plot(t4,bit,'g','linewidth',2.5);
grid on;
axis([0 bp*length(mn) -.5 1.5]);
ylabel('amplitude(volt)');
xlabel('time(sec)');
title('ASK demodulated waveform');

waveform:-

You might also like