BASIC TECHNOLOGY

Class: JSS 1

OBJECTIVE

1. _______ is any types of structure that has a roof and walls (a) Bus (b) Building (c) Lorry (d) Car
2. ________ is the type of house built completely on one level (e.g. ground) (a) Bungalow

(b) Semi-detached (c) Hut (d) High – rise

3. __________ is used as the drawing horizontal lines and supporting set squares (a) Drawing

Board (b) Tee Square (c) Protractor (d) French curve

4. The tee square consists of two parts namely the stock and _________ (a) The saw (a) The blade
c) The top (d) The bottom
5. A skyscraper is made up of how many floors a) 30 b) above 40 c) above 50 d) above 100
6. The protractor is used to measure angle between 0 and _______ (a) 32 (b) 180 (c) 90(d) 30
7. French curves are used to draw ____ curved lines (a) Regular (b) Straight (c) Irregular (d) Circle
8. ________ is used to transfer measurement from one past of the drawing to another
(a) Divides (b) Compass (c) Protractor (d) Steel rule
9. _________ is drawn to identify drawing (a) Title block (b) Box (c) Circle (d) Rectangles
10. _________ contains name, school, class and date (a) Title block (b) Title book (c) Box name
(d) Box school
11. Mixture of sand, cement, gravel with water is called (a) Concrete (b) Alloy (c) Gum (d) Ceramics
12. This is used for beautification of houses (a) Ceramics (b) Calendar (c) Curtin (d) Wall Clock
13. __________ can be defined as a room or building in which things are made repaired

and maintained a) workshop b) sitting room c) house d) workshop layout

14. The following are the operation performed in the workshop except (a) construction
(a) Repair (c) maintenance (d) surgery
15. Wood can be classified into ________ and ______ (a) hard and wet wood ( b) soft and wet
c)Hard and softwood (d) Cheap and expensive wood
16. ___________ can be defined as a technical language used for describing things with the aid of
drawing (a) Technical drawing (b) Drawing materials (c) drawing instrument (d) Drawing board
17. _________ is used for determining angle at various degrees. (a) Protractor (b) steel rule c)
Steel lapel (d) Caliper
18. This is used for planning rough wood (a) Rip Saw (b) Jack plane (c) Force plane (d) Tee Square
19. The table on which wood worker perform their operation is called (a) workbench (b) Bench
box c) workshop table (d) Construction table
20. A title block is drawn at the (a) top left corner (b) bottom right corner (c) bottom left corner (d)
top right corner
21. Which of these instruments is used for free-hand sketching? (a) set square and pencil (b) tee
square and pencil (c) pencil and eraser (d) compass and pencil
22. The term ‘technology’ can be classified into (a) natural technology and artificial (b) rural
technology and urban technology (c) biological and physical technology (d) under-developed
and high developed technology
23. The instrument used for picking measurement from the ruler to the drawing is called (a)
compass (b) tee square (c) divider (d) scriber
24. Which of the following drawing instruments is used for vertical and diagonal lines? (a) steel rule
(b) set square (b) divider (d) metre rule
25. A metal which contains iron is known as (a) ferrous (b) aluminium (c) bronze (d) copper
26. The stock and blade of a Tee-square form an angle of (a) 30° (b) 60° (c) 90° (d) 120°
27. Natural rubber is made from a milky liquid called (a) latex (b) solution (c) plasticine (d) moisture
28. Curves line are drawn with (a) French curves (b) Set square (c) Ruler (d) Divider
29. The most commonly used hand tool is __________ a) hammer b) punches c) saw d) chisel
30. The title block is always at the _______ a) top right corner b) top left corner c) bottom right
corner d) bottom left corner
31. ______ is used on rough surfaces of wood a) Fore plane b) spoke plane c) Jack plane d) Try plane
32. ________ is used for taking linear measurements a) caliper b) protractor c) screw guage d) steel
rule
33. ______ is used to measure angles a) caliper b) protractor c) screw guage d) compass
34. _______ is an all purpose saw a) Rip b) Panel c) Cross-cut d) Hack
35. _______ is used to drive a slotted screw a) hammer b) punches c) screwdriver d) compass
36. ______ is used for making small holes in wood for screws and nails a) drill bit b) brace c) bradawl
d) ratchet
37. Which of these is an example of a screwdriver a) ball peen b) straight peen c) blocking head d)
Off-set
38. Checking the oil level in the engine of a car is a kind of _____ maintenance a) preventive b)
routine c) predictive d) corrective
39. There are _____ types of maintenance a) 2 b) 3 c) 4 d) 6
40. The saw shown below is a ______ saw

A)Dovetail b) fret c) bow d) rip

45. The language of communication used among technical people is a) English language b)
French language c) German language d) Technical drawing
46. To draw regular circles and curves, ____ is used a) set square b) a pair of compasses c)
French curve d) ruler
 47. The following materials can be used for making roofs except ____ a) leaves b) metals c)
concrete d) sand
48. Lettering in technical drawing should be in single stroke _____ lines a) upright b) inclined c)
upright or inclined d) inverted
49. _____ is used to hold down the drawing sheet to the board after setting a) paper clip b)
divider c) scales drawing d) eraser
50. A box that contains all the information of a drawing is a) drawing box b) information box c)
title block d) title box
51. The kind of drawing that does not involve the use of drawing instruments is called a)
isometric drawing b) oblique drawing c) fine art d) freehand sketching
52. When a car is scanned to detect possible fault is called ______ maintenance a) preventive b)
routine c) predictive d) corrective
53. The kind of maintenance done when there is a breakdown of equipment is called a)
Preventive b) routine c) predictive d) corrective
54. Which of the following is not a kind of preventive maintenance? a) oiling of sewing machines
b) gauging the water level in the radiator c) gauging the oil level in the radiator d) replacing
damaged parts of a machine
55. Which of the following is a corrective maintenance? a) adjusting the bolts and nuts b) oiling
the chain of bicycle c) removing a damaged chain of a bicycle d) none of the above
56. The following are hand tools used for mixing concrete except a) head pan b) hand trowel c)
shovel d) mixing truck
57. The following are drawing instruments except a) drawing board b) T-square c) safety pin d)
divider
58. One of the following is not needed in the title block a) name b) class c) age d) title of drawing
59. Writing of letters and numerals on drawing without the templates is known as a) freehand
sketching b) freehand drawing c) freehand lettering d) all of the above
60. Which of these saw has a steel back a) Dovetail saw b) Tenon saw c) back saw d) Fret saw

THEORY

Answer all questions

INSTRUCTIONS :

I. Make sure your pencils are sharp

QUESTION 1a : On an A4 paper make the following 1. Border lines 2. A title block with the following I.
Name II. School III. Class iv.Subject v. Date
b. Sketch the diagram below

QUESTION 2: Mention 5 importance of maintaining tools and machines