Scribd
Upload
43 views3 pages

Controlcable 16C 1.5sqmm

Uploaded by

chida moha
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
43 views3 pages

Controlcable 16C 1.5sqmm

Uploaded by

chida moha
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 3

1 APPLICATION/ PART NO.

CONTROL as per IS - 1554


2 NO. OF PAIRS/Core 8 PAIR / 16 core
General

3 TWISTED PAIRS/ OVER LAY >10 twists or more per Meter / yes
4 CABLE O.D. 21 mm
5 INDIVIDUAL PAIR SHIELDING/ MATL. NOT APPLICABLE
6 OVERALL SHIELD / MATL. YES / AL. MYLAR TAPE
7 TYPE OF SCREENING 100% COVERAGE WITH 25%OVERLAP
8 CONDUCTOR MATL. / TYPE TINNED COPPER / Stranded
9 CONDUCTOR STANDARD IS- 8130
Conductor

10 CONSTRUCTION STRANDED 7 X 0.53 mm DIA


11 CONDUCTOR CROSS SECTION 1.5 mm2
12 CONDUCTOR INSULATION / STANDARD LDPE / IS 6474
13 INSULATION COLOR BLACK (+ve) & LIGHT BLUE(-ve)
14 INNER SHEATH / COLOUR (ST2 - IS5831) FRLS PVC / BLACK(ST-2-IS5831/IEC-502)
Construction

15 OUTER SHEATH / COLOUR FRLS PVC 1.6 mm THK * / GREY(ST-2-IS5831/IEC-502)


16 DRAIN WIRE MATL. & SIZE TINNED COPPER 7 X 0.3 mm DIA
17 RIP CORD REQUIRED BELOW INNER SHEATH
18 ARMOUR TYPE IS - 3975 GALVANISED STEEL WIRE 1.6mm DIA.
19 CORE IDENTIFICATION / NUMBERING PAIR NO. ON EACH CORE AT EVERY 50mm
20 INSULATION RESISTANCE OHM/Km >5000 MEGA OHM /KM at 20 Deg C. AS PER BS-5308
21 FLAME RETARDANCE IEC 332 PART III TYPE A
22 VOLTAGE GRADE (Volts) 600 V / 1100 V
23 ELECTROSTATIC NOISE REJECTION
24 CONDUCTOR RESISTANCE Ohm / Km @ 20 C 12.3 OHMS / KM
25 MUTUAL CAPACITANCE max.
(a) BETWEEN CORE TO CORE
(b) BETWEEN CORE TO SCREEN
26 INDUCTANCE AT 1 kHz mH/Km max. 1.2
Testing

27 L / R RATIO μH / OHM max 40


28 DIELECTRIC TEST VOLTAGE Tests as per IS- 1554 Part I
(a) CORE TO CORE **
(b) CORE TO SHIELD
(c) ARMOUR TO SHIELD
(d) SHIELD TO SHIELD
(e) SPARK TEST DURING PRODUCTION
29 OXYGEN INDEX (%) >29 AS PER ASTM D 2863
30 TEMPERATURE INDEX (OC) AS PER ASTM D 2863
31 ACID GAS EMISSION (%) AS PER IEC- 754 - 1
32 SMOKE INDEX (% ABSORBANCE) AS PER ASTM D 2843
33 OVERALL OUTER DIAMETER (mm) ± 1 mm *
34 DIAMETER BELOW ARMOUR (mm) ± 1 mm *
35 DIAMETER ABOVE ARMOUR (mm) ± 1 mm *
36 NET WEIGHT OF CABLE PER KM *
1) * Manuf. To specify.
NOTES
2) THE SUPPLIED CABLE SHALL NOT HAVE VARIATION IN DIAMETER FROM PLACE TO PLACE MORE THAN ±0.
3) NEGATIVE TOLERANCE IN LENGTH IS NOT ACCEPTABLE.
NOTES

4) ALL CABLES SHALL WATER, OIL & SUNLIGHT RESISTANT, GAS & VAPOUR TIGHT.

THE DRAIN WIRE RESISTANCE INCLUDING SHIELD SHALL NOT EXCEED 30 OHMS/ KM. THE DRAIN WIRE
5)
SHALL BE IN CONTINEOUS CONTACT WITH THE SIDE OF THE SHIELD.

EMBOSSING MARKING PER METER OF THE CABLE SHALL BE CLEAR & PROMINENT.RUNNING LENGTH OF
6)
CABLE SHALL BE PRINTED AT LEAST EVERY 5 METER INTERVAL.

You might also like