Insulated
Roller Shutter
Description:This shutter is designed to
207 Version 5
comply with the current British and EEC
safety regulations. Optional specification
levels can be varied to meet any special
operational requirements.
Standards & Quality: Compliant with Speedor Super
prEN 13241-1:2003 & manufactured
and installed to iso 9001/2001 and is
CE marked.
Door Curtain: Constructed from
100 x 25 double skin interlocking
galvanised steel sections and retained
at ends by nylon end locks. The door Speedor Mini
curtain is made up from an insulated lath
section giving a thermal insulation value
of 0.69w/m.sq.k across the lath section
and an acoustic value reduction of 18db
SELF LOCK GUIDE
across the lath section. SYSTEM
Bottom Rail: Fitted with a SECURITY
VISION
purpose-designed extrusion complete WIND
ENDLOCK PANEL
with interlocking (EPDM) rubber weatherseal. Speedor Combi
Drive System: The Safedrive
Door Guides: Continuous steel angle bolted to unit has been specially
the door jamb supporting an 88mm deep guide channel. The channel developed for roller shutter
has nylon seals down internal edges of the guide mouth. Guides are pre- doors which are non-spring counter balanced. The drive is provided by
galvanized prior to rolling and can be optionally powder coated at extra hollow shaft keyed drive through the door axle. It has been designed for
cost to match the door colour. a long service life and has a built in safety brake device which conforms
to all current BSEN industrial and commercial safety standards. The unit
End Plates: Circa 500mm square shutter steel end plate with steel angle also has a build in limit switch.
fixing to door frame. The end plates support the weight of the shutter and Roller Shutters Fire
and/or Security
are fixed through the angles by 3 No. M12 hex bolts. Manual Override: All doors are supplied as standard with a Ground
Floor Hand Chain Operation with floor level engagement, or crank handle
Roller: A 140 x 5mm steel tube adequate to prevent deflection of less operation at the motor, for emergency operation. (Note: this is heavy and
than 400:1 of welded construction with steel supporting axles on ball slow to operate)
bearings, non counterbalanced i.e. no springs. The assembly will be
prime painted with exception of the axles which will be wax coated. Control Panel: The IP 65 enclosure incorporates open, close and stop
buttons with the provision for installing a key switch and/or latching stop
Seal at Head: A brush seal will be provided across the head of the door button if required. It houses a digital control system which allows for limit Automatic Conveyor
to close the opening from outside. switch setting from ground level, has a programmable door maintenance Door
indicator, load monitoring in the open direction, digital display of door
Hoods: Supplied as an option in 0.9mm pre-galvanised sheet steel, status and/or fault diagnosis, and meets the requirements of BS EN
folded around the end plate assemblies to form a three sided enclosure 12453.
and fixed directly to the door support frame through a flange provided
along its top edge . The sections will be joined with a vertical joggle Normal Operation: Press buttons in full view of door. Impulse open and
connection. The hood may be powder coated, at extra cost, to match the “hold to run” close. Options include key switch. To operate by momentary
door colour. pressure, safety systems need to be included.
Machine Guard
Power Supply: The 3 phase, neutral and earth, 16amp 380/440V AC Safety: As standard, fitted with either an integral motor safety brake or Automated
power supply will terminate in a Euro 5 pin industrial socket within 1 an auxiliary safety brake, depending on motor choice. Optional optical
meter of the door control panel on the motor side at approximately 1.5M safe edge on the bottom rail, photo cell protection, warning signs, and
above floor level. The press button controls will be mounted at increased protection levels as required.
approximately 1.2M above floor level. The wiring connections between
the control panel and the motor will be in braided cable with plug and Operating Speed: The standard travel speed is circa 100-200mm/sec
sockets arrangements to allow for easy site installation. The cable will depending on door size and weight
then be surface clipped.
High Speed Fire
Finishes: Galvanised steel as standard with options for Plastisol or RAL Resistant Conveyor
powder coated finish to one or both sides of the curtain.
Optional Automatic Operation: Full automatic operation via control
panel by remote induction loop, radio control, with full safety systems.
Fire Shutter to UK or
US Standards
Hart Door Systems Limited
Westerhope Industrial Estate, Newcastle upon Tyne NE5 1PJ UK
Tel: +44 (0)191 214 0404 Fax: +44 (0)191 2711611
[email protected] www.hartdoors.com
These datasheets are generated internally so that the information we provide is as up-to-date as possible, incorporating all changes
introduced by continuous improvement of our products. We reserve the right to change specifications at any time without notice.
Datasheet 207 Version 5
TS961
DOOR CONTROL
Architectural Shortform:
Electrically operated steel roller shutter with 100mm x 25mm double skin interlocking galvanised steel laths and nylon end locks.
Lath section with insulating layer giving a thermal insulation value of 0.69w/m sq k and acoustic reduction of 18Db.
To be driven via Safedrive direct drive motor unit with built in safety brake and complete with surface clipped braided cable pre-
wired control panel with up, down press buttons and emergency stop.
Options: hoods, finish, safety, automatic operation.
Assessed to ISO 9001 Approved to LPS 1056. LPCB ref.016a/01
LPCB ref. no 016 Approved to LPS 1271. LPCB ref.016b/01
