Copyright

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable.
However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or
other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications
at any time without notice.

Copyright © 2005 by
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618

All rights reserved. Printed in Taiwan

Trademarks:
SMC is a registered trademark; and EZ Connect is a trademark of SMC Networks,
Inc. Other product and company names are trademarks or registered trademarks of their respective holders.
 LIMITED WARRANTY
Limited Warranty Statement: SMC Networks, Inc. (.SMC.) warrants its products to be free
from defects in workmanship and materials, under normal use and service, for the applicable
warranty term. All SMC products carry a standard 90-day limited warranty from the date of
purchase from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or
replace any product not operating as warranted with a similar or functionally equivalent
product, during the applicable warranty term. SMC will endeavor to repair or replace any
product returned under warranty within 30 days of receipt of the product.

The standard limited warranty can be upgraded to a Limited Lifetime* warranty by registering
new products within 30 days of purchase from SMC or its Authorized Reseller. Registration
can be accomplished via the enclosed product registration card or online via the SMC Web
site. Failure to register will not affect the standard limited warranty. The Limited Lifetime
warranty covers a product during the Life of that Product, which is defined as the period of
time during which the product is an .Active. SMC product. A product is considered to be
.Active. while it is listed on the current SMC price list. As new technologies emerge, older
technologies become obsolete and SMC will, at its discretion, replace an older product in its
product line with one that incorporates these newer technologies. At that point, the obsolete
product is discontinued and is no longer an .Active. SMC product. A list of discontinued
products with their respective dates of discontinuance can be found at:
http://www.smc.com/index.cfm?action=customer_service_warranty.

All products that are replaced become the property of SMC. Replacement products may be
either new or reconditioned. Any replaced or repaired product carries either a 30-day limited
warranty or the remainder of the initial warranty, whichever is longer. SMC is not responsible
for any custom software or firmware, configuration information, or memory data of
Customer contained in, stored on, or integrated with any products returned to SMC pursuant
to any warranty. Products returned to SMC should have any customer-installed accessory or
add-on components, such as expansion modules, removed prior to returning the product for
replacement. SMC is not responsible for these items if they are returned with the product.

Customers must contact SMC for a Return Material Authorization number prior to returning
any product to SMC. Proof of purchase may be required. Any product returned to SMC
without a valid Return Material Authorization (RMA) number clearly marked on the outside
of the package will be returned to customer at customer.s expense. For warranty claims within
North America, please call our toll-free customer support number at (800) 762-4968.
Customers are responsible for all shipping charges from their facility to SMC. SMC is
responsible for return shipping charges from SMC to customer.

ii
WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS
WARRANTED ABOVE, CUSTOMER.S SOLE REMEDY SHALL BE REPAIR OR
REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC.S OPTION. THE
FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN
LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED,
EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE,
INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR
AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION,
MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL NOT BE LIABLE
UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE
ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY
CUSTOMER.S OR ANY THIRD PERSON.S MISUSE, NEGLECT, IMPROPER
INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR
ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY
ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.

LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT

OR TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR
INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE
DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE
SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR
INTERRUPTION OF ITS PRODUCTS, EVEN IF SMC OR ITS AUTHORIZED
RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES

OR THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR
CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS
MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS
WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.

* SMC will provide warranty service for one year following discontinuance from the active
SMC price list. Under the limited lifetime warranty, internal and external power supplies, fans,
and cables are covered by a standard one-year warranty from date of purchase.

SMC Networks, Inc.

38 Tesla
Irvine, CA 92618

iii
COMPLIANCES
FCC - Class A
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that the interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

• Reorient the receiving antenna

• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help
•
EC Conformance Declaration - Class A
SMC contact for these products in Europe is:
SMC Networks Europe,
Edificio Conata II,
Calle Fructuós Gelabert 6-8, 2o, 4a,
08970 - Sant Joan Despí,
Barcelona, Spain.
This information technology equipment complies with the requirements of the Council
Directive 89/336/EEC on the Approximation of the laws of the Member States relating to
Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain
voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the
compliance with these Directives, the following standards were applied:
RFI Emission:
• Limit class A according to EN 55022:1998, IEC 60601-1-2 (EMC,medical)
• Limit class A for harmonic current emission according toEN 61000-3-2/1995
• Limitation of voltage fluctuation and flicker in low-voltage supply system according to
EN 61000-3-3/1995
Immunity:
• Product family standard according to EN 55024:1998

iv
 • Electrostatic Discharge according to EN 61000-4-2:1995
(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)
• Radio-frequency electromagnetic field according to EN 61000-4-3:1996
(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)
• Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/DC
power supply: ±1 kV, Data/Signal lines: ±0.5 kV)
• Surge immunity test according to EN 61000-4-5:1995
(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)
• Immunity to conducted disturbances, Induced by radio-frequency fields:
EN 61000-4-6:1996 (0.15 - 80 MHz with
1 kHz AM 80% Modulation: 3 V/m)
• Power frequency magnetic field immunity test according to
EN 61000-4-8:1993 (1 A/m at frequency 50 Hz)
• Voltage dips, short interruptions and voltage variations immunity test
according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%
Reduction @500 ms, >95% Reduction @5000 ms)
LVD:
• EN 60950-1:2001

Industry Canada - Class A

This digital apparatus does not exceed the Class A limits for radio noise emissions from
digital apparatus as set out in the interference-causing equipment standard entitled .Digital
Apparatus,. ICES-003 of the Department of Communications.
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils
numériques de Classe A prescrites dans la norme sur le matériel brouilleur: .Appareils
Numériques,. NMB-003 édictée par le ministère des Communications.

v
EZ Switch 10/100
User Guide
From SMC’s EZ line of low-cost workgroup LAN solutions

38 Tesla
Irvine, CA 92618 November 2005
Phone: (949) 679-8000 Pub #: 150001624DT0H R01
Please read the following safety information carefully
before installing the Switch:

WARNING: Installation and removal of the unit must be carried out by

qualified personnel only.
• This guide is intended for use by network administrators who are
responsible for setting up and installing network equipment;
consequently it assumes a basic working knowledge of LANs (Local
Area Networks).
• The unit must be connected to an earthed (grounded) outlet to
comply with international safety standards.
• Do not connect the unit to an A.C. outlet (power supply) without an
earth (ground) connection.
• The appliance coupler (the connector to the unit and not the wall plug)
must have a configuration for mating with an EN 60320/IEC 320
appliance inlet.
• The socket outlet must be near to the unit and easily accessible. You
can only remove power from the unit by disconnecting the power
cord from the outlet.
• This unit operates under SELV (Safety Extra Low Voltage) conditions
according to IEC 60950. The conditions are only maintained if the
equipment to which it is connected also operates under SELV
conditions.

vi
France and Peru only
This unit cannot be powered from IT. supplies. If your supplies are of IT type, this unit must
be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the secondary connection
point labelled Neutral, connected directly to earth (ground).
†Impédance à la terre

Power Cord Set

U.S.A. and Canada The cord set must be UL-approved and CSA certified.
The minimum specifications for the flexible cord are: - No. 18
AWG - not longer than 2 meters, or 16 AWG. - Type SV or SJ -
3-conductor

The cord set must have a rated current capacity of at least 10A.
The attachment plug must be an earth-grounding type with
NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V)
configuration.
Denmark The supply plug must comply with Section 107-2-D1, Standard
DK2-1a or DK2-5a.

Switzerland The supply plug must comply with SEV/ASE 1011.

U.K. The supply plug must comply with BS1363 (3-pin 13 A) and be
fit-ted with a 5 A fuse which complies with BS1362.

The mains cord must be <HAR> or <BASEC> marked and be

of type HO3VVF3GO.75 (minimum).
Europe The supply plug must comply with CEE7/7 (.SCHUKO.).

The mains cord must be <HAR> or <BASEC> marked and be

of type HO3VVF3GO.75 (minimum).

IEC-320 receptacle.

Veuillez lire à fond l’information de la sécurité

suivante avant d’installer le Switch:
AVERTISSEMENT: L.installation et la dépose de ce groupe doivent être
confiés à un personnel qualifié.
• Ne branchez pas votre appareil sur une prise secteur (alimentation
électrique) lorsqu’il n’y a pas de connexion de mise à la terre (mise à la
masse).

vii
 • Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la
masse) afin de respecter les normes internationales de sécurité.
• Le coupleur d.appareil (le connecteur du groupe et non pas la prise
murale) doit respecter une configuration qui permet un branchement
sur une entrée d.appareil EN 60320/IEC 320.
• La prise secteur doit se trouver à proximité de l.appareil et son accès
doit être facile. Vous ne pouvez mettre l.appareil hors circuit qu.en
débranchant son cordon électrique au niveau de cette prise.
• L.appareil fonctionne à une tension extrêmement basse de sécurité qui
est conforme à la norme IEC 60950. Ces conditions ne sont
maintenues que si l.équipement auquel il est raccordé fonctionne dans
les mêmes conditions.

France et Pérou uniquement:

Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos alimentations
sont du type impédance à la terre, ce groupe doit être alimenté par une tension de 230 V
(2 P+T) par le biais d.un transformateur d.isolement à rapport 1:1, avec un point secondaire
de connexion portant l.appellation Neutre et avec raccordement direct à la terre (masse).

Cordon électrique - Il doit être agréé dans le pays d.utilisation

Etats-Unis et Can- Le cordon doit avoir reçu l′homologation des UL et un
ada: certificat de CSA.
Les spe’cifications minimales pour la corde flexible sont AWG
No. 18, ou AWG No. 16 pour une longueur infe’rieure a‘ 2
me’tres:
- type SV ou SJ
- 3 conducteurs
Le cordon doit être en mesure d.acheminer un courant nominal
d.au moins 10 A.

La prise femelle de branchement doit être du type à mise à la terre

(mise à la masse) et respecter la configuration NEMA 5-15P (15 A,
125 V) ou NEMA 6-15P (15 A, 250 V).
Danemark: La prise mâle d.alimentation doit respecterla la section 107-2
D1 de norme DK2 1a ou DK2 5a.

viii
 Cordon électrique - Il doit être agréé dans le pays d.utilisation
La prise mâle d.alimentation doit
Suisse:
respecter la norme SEV/ASE 1011.
La prise secteur doit être conforme aux normes CEE 7/7 (.SCHU-
Europe
KO.
LE cordon secteur doit porter la mention <HAR> ou <BASEC>
et doit être de type HO3VVF3GO.75 (minimum).

Bitte unbedingt vor dem Einbauen des RPU die

folgenden Sicherheitsanweisungen durchlesen:

WARNUNG: Die Installation und der Ausbau des Geräts darf nur durch
Fachpersonal erfolgen.
• Diese Anleitung ist fr die Benutzung durch Netzwerkadministratoren
vorgesehen, die fr die Installation und das einstellen von
Netzwerkkomponenten verantwortlich sind; sie setzt Erfahrung bei der
Arbeit mit LANs (Local Area Networks) voraus.
• Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose
angeschlossen werden.
• Das Gerät muß an eine geerdete Steckdose angeschlossen werden,
welche die internationalen Sicherheitsnormen erfüllt.
• Der Gerätestecker (der Anschluß an das Gerät, nicht der
Wandsteckdosenstecker) muß einen gemäß EN 60320/IEC 320
konfigurierten Geräteeingang haben.
• Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich
sein. Die Stromversorgung des Geräts kann nur durch Herausziehen des
Gerätenetzkabels aus der Netzsteckdose unterbrochen werden.
• Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen
(Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind
nur gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter
SELV-Bedingungen betrieben werden

ix
Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft werden:
Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen ein-
Schweiz
halten.
Europe Das Netzkabel muß vom Typ HO3VVF3GO.75 (Mindestan-
forderung) sein und die Aufschrift <HAR> oder <BASEC>
tragen
Der Netzstecker muß die Norm CEE 7/7 erfüllen (.SCHUKO.).

Warnings and Cautionary Messages

Warning: This product does not contain any serviceable user parts.
Warning: Installation and removal of the unit must be carried out by qualified personnel
only.
Warning: When connecting this device to a power outlet, connect the field ground lead
on the tri-pole power plug to a valid earth ground line to prevent electrical
hazards.
Caution: Wear an anti-static wrist strap or take other suitable measures to prevent
electrostatic discharge when handling this equipment.
Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this
device. Les raccordeurs ne sont pas utilisé pour le système téléphonique!
Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC
standards.

Warnings (in German)

Achtung: Dieses Produkt enthält keine Teile, die eine Wartung vom Benutzer benötigen.
Achtung: Installation und Deinstallation des Gerätes müssen von qualifiziertem
Servicepersonal durchgeführt werden.
Achtung: Wenn das Gerät an eine Steckdose angeschlossen wird, muß der Masseanschluß
n Netzstecker mit Schutzerde verbunden werden, um elektrische
Gefahren zu vermeiden.

x
Environmental Statement
The manufacturer of this product endeavours to sustain an environmentally-friendly policy
throughout the entire production process. This is achieved though the following means:
• Adherence to national legislation and regulations on environmental production standards.
• Conservation of operational resources.
• Waste reduction and safe disposal of all harmful un-recyclable by-products.
• Recycling of all reusable waste content.
• Design of products to maximize recyclables at the end of the product.s life span.
• Continual monitoring of safety standards.

End of Product Life Span

This product is manufactured in such a way as to allow for the recovery and disposal of all included
electrical components once the product has reached the end of its life.

Manufacturing Materials
There are no hazardous nor ozone-depleting materials in this product.

Documentation
All printed documentation for this product uses biodegradable paper that originates from
sustained and managed forests. The inks used in the printing process are non-toxic.

Purpose
This guide details the hardware features of the switch, including Its physical and
performance-related characteristics, and how to install the switch.

Audience
The guide is intended for use by network administrators who are responsible for installing and
setting up network equipment; consequently, it assumes a basic working knowledge of LANs
(Local Area Networks).
Diese Anleitung ist für die Benutzung durch Netzwerkadministratoren vorgesehen, die für die
Installation und das einstellen von Netzwerkkomponenten verantwortlich sind; sie setzt
Erfahrung bei der Arbeit mit LANs (Local Area Networks) voraus.

xi
TABLE OF CONTENTS
Introduction 1
Features and Benefits 1
Front Panel LED’s 2
Unit Drawings 3
Rear Panel 3

Installing the Switch 4

Package Contents 4
Selecting a Site 4
Instructions 5

Troubleshooting 7
Diagnosing Switch Indicators 7

Cables 8
Cable Specifications 8

Product Specifications 10
 INTRODUCTION
The EZ Switch™ 10/100 SMC-EZ1024DT and SMC-EZ1016DT are 24/16-
port Fast Ethernet switches. The 10BASE-T/100BASE-TX ports deliver
dedicated 10/100 Mbps links to each attached LAN segment – all with
conventional cabling and adapters.
Auto-negotiation is used to select the optimal communication mode for
each connection. Auto-sensing is used to select the optimal transmission
speed for each connection. With store-and-forward switching and flow
control, maximum data integrity is always maintained, even under heavy
loading. Easy installation and reliability make this plug-and-play switch an
ideal choice for smooth Fast Ethernet integration.

Features and Benefits

• Auto-negotiation of half or full duplex, and auto-sensing of
transmission speed, on all ports

• Auto configuration for MDI/MDI-X cable connection allows

connections to servers, workstations, hubs or switches to be made
with straight-through cabling

• ANSI/IEEE 802.3u compliance ensures compatibility with

standards-based hubs, switches and cards from any vendor

• Store-and-forward switching ensures error-free transmission

• Half- and full-duplex flow control prevents packets from being

dropped under heavy loading

• Plug-and-play

• “At-a-glance” LEDs for port and system status monitoring

• Desktop and rack mountable

1
Front Panel LEDs
The front panel of the switch provides a link status LED for each RJ-45
port. In addition, the front panel also contains status LEDs for
“at-a-glance” system monitoring. The following table details the functions
of the various indicators:

Port and Switch Status LEDs

LED Condition Status

Power On Green The switch is receiving power.
Ports
Link/Act On The port has established a valid network
connection.
Flashing Traffic is passing through the port.
Off The port has not established any network
connection.
10/100 On Indicates the port is operating at 100Mbps
Off Indicates the port is operating at 10 Mbps.

2
Front Panel
SMC-EZ1024DT

SMC-EZ1016DT

Rear Panel
The AC power connector is located on the rear panel of the switch.

3
 INSTALLING THE SWITCH
Before installing the switch, verify that you have all the items listed under
“Package Contents.” Note that the switch can be installed on any suitably
large flat surface or in a standard EIA 19-inch rack.

Package Contents
The EZ Switch 10/100 includes:
• EZ Switch 10/100 (SMC-EZ1016DT or SMC-EZ1024DT)
• Four rubber foot pads
• Rack-mount bracket kit
• Appropriate AC power cord
• This User Guide
• SMC Warranty Registration Card

Selecting a Site
Be sure to follow the site selection guidelines below when choosing a
location:
• Select a suitable location for the switch:
o It should be accessible for installing, cabling and maintaining the
switch.

o The temperature and humidity should be within the ranges listed

in the specifications.

o The status LEDs should be clearly visible.

o There should be adequate space (approximately two inches) on all

sides for proper air flow.

4
 • Make sure twisted-pair cable is always routed away from power lines,
fluorescent lighting fixtures and other sources of electrical
interference such as radios, transmitters, etc.
• Make sure that a properly grounded power outlet is within 2.44 meters
(8 feet) of the switch and is powered from an independent circuit
breaker. As with any equipment, using a filter or surge suppressor is
recommended.

Instructions
1. Positioning the Switch: For desktop or shelf mounting, attach the
four adhesive foot pads to the bottom of the switch. For rack
mounting, install into a standard EIA 19-inch rack using the included
brackets.

2. Applying Power: Plug one end of the power adapter into the socket
on the switch.s rear panel, and the other end into an appropriate
electrical outlet. Check the Power LED to be sure power is on.

Note: It is not necessary to power off the switch before connecting or

disconnecting any UTP cables, as these actions will not disrupt
the operation of other devices attached to the switch.

3. Connecting PCs: Connect each PC to an RJ-45 port on the switch

using Category 5 or 5e shielded or unshielded twisted-pair (UTP or
STP) cable, maximum length 100 meters (328 ft). The EZ Switch 10/
100 will support up to 16 or 24 PCs. All ports on the switch support
automatic MDI/MDI-X operation, so you can use straight-through
cables for all network connections to PCs or servers, or to other
switches or hubs.

Note: If an attached device does not support auto-negotiation, the data

rate will be sensed automatically and the communication mode
will default to half duplex.

5
4. Cascading Switches and Other Network Devices: All the ports on
the switch support automatic MDI/MDI-X configuration for cable
connections. This allows you to use straight-through cable to connect
to other switches or hubs from any port on the switch. No crossover
cables or other device settings are needed. See the Cable
Specifications.

Caution: Do not plug a phone jack connector into any RJ-45 port. This
the switch. Instead, use only twisted-pair cables
with RJ-45 connectors that conform with FCC standards.

6
 TROUBLESHOOTING
Diagnosing Switch Indicators
1. Symptom
Power LED does not light after power on.

Probable Causes
o AC power cord may be defective.

Possible Solutions
o Check for loose connections.
o Check the power outlet by using it for another device.
o Replace the AC power cord.

2. Symptom
Link LED does not light after connection is made.

Probable Causes
o Switch port, network card or cable may be defective.

Possible Solutions
o Check that the switch and attached device are both powered
on.
o Be sure the network cable is connected to both devices.
o Verify that Category 5 or better cable is used for 10/100
Mbps connections and that the length of any cable does not
exceed 100 meters (328 feet).
o Check the network card and cable connections for defects.
o Replace the defective card or cable if necessary.

7
 CABLES
Cable Specifications

Cable Types and Specifications

Cable Type Max. Length Connector
2-pair Cat. 3 or better 100-ohm
10BASE-T 100 m (328 ft) RJ-45
UTP
2-pair Cat. 5 or better 100-ohm
100BASE-TX 100 m (328 ft) RJ-45
UTP

10BASE-T/100BASE-TX Pin Assignments

Caution: DO NOT plug a phone jack connector into any RJ-45 port.
Use only twisted-pair cables with RJ-45 connectors that
conform with FCC standards.

Use unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable for

RJ-45 connections: 100-ohm Category 3 or better cable for 10 Mbps
connections or 100-ohm Category 5 or better cable for 100 Mbps
connections. Also be sure that the length of any twisted-pair connection
does not exceed 100 meters (328 feet).

Because all ports on this switch support automatic MDI/MDI-X

operation, you can use straight-through cables for all network connections
to PCs or servers, or to other switches or hubs. In straight-through cable,
pins 1, 2, 3, and 6, at one end of the cable, are connected straight through
to pins 1, 2, 3 and 6 at the other end of the cable.

8
The table below shows the 10BASE-T/100BASE-TX MDI-X and MDI
port pinouts.

Pin MDI-X Signal Name MDI Signal Name

1 Receive Data plus (RD+) Transmit Data plus (TD+)
2 Receive Data minus (RD-) Transmit Data minus (TD-)
3 Transmit Data plus (TD+) Receive Data plus (RD+)
6 Transmit Data minus (TD-) Receive Data minus (RD-)
4,5,7,8 Not used at 10/100 Mbps Not used at 10/100 Mbps

9
 PRODUCT SPECIFICATIONS
EZ Switch 10/100
Standards Conformance
IEEE 802.3-2002
Ethernet, Fast Ethernet
Full-duplex flow control

Communication Rate
10 and 100Mbps

Communication Mode
Full or half duplex at 10/100 Mbps

Media Supported
10BASE-T: 100-ohm Category 3 or better twisted-pair
100BASE-TX: 100-ohm Category 5 or better twisted pair

Number of Ports
SMC-EZ1016DT: 16 RJ-45 10/100 BASE-T ports
SMC-EZ1024DT: 24 RJ-45 10/100 BASE-T ports

Indicator Panel
Power
Ports: Link/Act, 10/100M

Dimensions
28x17.3x4.4 cm (11x6.8x1.7 in.)

Weight
SMC-EZ1016DT: 1.6 kg (3.5 lbs)
SMC-EZ1024DT: 1.7 kg (3.7 lbs)

10
MAC Address Table
8 K entries

Memory Buffer
SMC-EZ1016DT: 1.25 Mbits on-chip frame buffer
SMC-EZ1024DT: 1.25 Mbits on-chip frame buffer

Power Consumption
SMC-EZ1016DT: 11 Watts
SMC-EZ1024DT: 13 Watts

Power Requirement
Input Voltage: 100 - 240 VAC@50-60 Hz

Temperature
Operating: 0 ~ 50 ºC / 32 ~ 122 ºF
Storage: -20 ~ 70 ºC / -4 ~ 158 ºF

Humidity
5% to 95% non-condensing

EMC/Safety Compliances
CE Mark

Immunity
EN 61000-4-2/3/4/5/6/8/11

Emissions
FCC Class A, CISPR Class A, EN 61000-3-2/3

Safety
CSA/CUS (CSA60950-1 & UL60950-1)
TUV / GS EN60950-1
CB IEC60950-1

11
FOR TECHNICAL SUPPORT, CALL:
From U.S.A. and Canada (24 hours a day, 7 days a week)
(800) SMC-4-YOU; Phn: (949) 679-8000; Fax: (949) 679-1481
From Europe : Contact details can be found on www.smc.com

INTERNET
E-mail address:
[email protected]

Driver updates:
http://www.smc.com/index.cfm?action=tech_support_drivers_downloads

World Wide Web:

http://www.smc.com

For Literature or Advertising Response, Call:

U.S.A. and Canada: (800) SMC-4-YOU Fax (949) 679-1481

Spain: 34-91-352-00-40 Fax 34-93-477-3774
UK: 44 (0) 1932 866553 Fax 44 (0) 118 974 8701
France: 33 (0) 41 38 32 32 Fax 33 (0) 41 38 01 58
Italy: 39 (0) 3355708602 Fax 39 02 739 14 17
Benelux: 31 33 455 72 88 Fax 31 33 455 73 30
Central Europe: 49 (0) 89 92861-0 Fax 49 (0) 89 92861-230
Nordic: 46 (0) 868 70700 Fax 46 (0) 887 62 62
Eastern Europe: 34 -93-477-4920 Fax 34 93 477 3774
Sub Saharan Africa: 216-712-36616 Fax 216-71751415
North West Africa: 34 93 477 4920 Fax 34 93 477 3774
CIS: 7 (095) 7893573 Fax 7 (095) 789 357
PRC: 86-10-6235-4958 Fax 86-10-6235-4962
Taiwan: 886-2-87978006 Fax 886-2-87976288
Asia Pacific: (65) 238 6556 Fax (65) 238 6466
Korea: 82-2-553-0860 Fax 82-2-553-7202
Japan: 81-45-224-2332 Fax 81-45-224-2331
Australia: 61-2-8875-7887 Fax 61-2-8875-7777
India: 91-22-8204437 Fax 91-22-8204443

If you are looking for further contact information, please visit www.smc.com

Model Number: SMC-EZ1016DT / SMC-EZ1024DT

38 Tesla
Irvine, CA 92618
Phone: (949) 679-8000