—

T&B® Cable Tray

Nonmetallic cable tray systems
—
B

T&B Cable Tray

Nonmetallic cable tray systems
—
Table of contents
Section B
Overview B5
Technical information B7
FRP cable tray specifications B13
Nonmetallic cable tray - Straight lengths B14
Nonmetallic cable tray - Fittings B23
Nonmetallic cable tray - Splice plates B38
Nonmetallic cable tray systems B42
Nonmetallic cable tray - Covers B44
Nonmetallic cable tray - Accessories B45
Nonmetallic channel tray - Straight lengths B46
Nonmetallic channel tray - Fittings B48
Nonmetallic channel tray systems B50
Nonmetallic strut systems B52
 B4 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S
SECTION 19
 N O N M E TA L L I C - C A B L E T R AY - O V E R V I E W B5

—
Nonmetallic - Cable tray
Overview
Why specify our cable tray?
Nonmetallic cable tray systems have been tested Mat
and proven in the harsh environment of the offshore Veil
oil and gas industry. This tray is ideally suited to Unidirectionally
aligned glass
withstand the corrosive conditions inherent in the fibers bonded
petroleum, mining, and fertilizer industries. In with resin
these applications, nonmetallic tray is exposed
daily to wind, weather, and saltwater.

Nonmetallic cable tray gives you the load capacity

of steel plus the inherent characteristics afforded
by our pultrusion technology: non-conductive,
non-magnetic and corrosion-resistant. Although
light in weight, their strength-to-weight ratio Polyester or vinylester surface
surpasses that of equivalent steel products.

—
01

—
01 A surface veil is applied
during the pultrusion
process to ensure a resin
rich surface for superior
corrosion resistance
as well as an ultraviolet
exposure barrier.
B6 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray
Overview (continued)

Why specify our cable tray?

Nonmetallic cable tray systems have been
tested and proven in the harsh environment of
the offshore oil and gas industry. This tray is ideally
suited to withstand the corrosive conditions
inherent in the petroleum, mining, and fertilizer
industries. In these applications, nonmetallic tray is
exposed daily to wind, weather, and saltwater.

Nonmetallic cable tray gives you the load

capacity of steel plus the inherent characteristics
afforded by our pultrusion technology:
non-conductive, non-magnetic and
corrosion-resistant. Although light in weight,
their strength-to-weight ratio surpasses that of
equivalent steel products.

—
Table 1 – Typical properties of pultruded components gland

Isophthalic Polyester
Properties Test method Unit/value Longitudinal Transverse
Tensile strength ASTM D638 psi 30,000 7,000
Tensile modulus ASTM D638 psi x 10⁶ 2.5 0.8
Flexural strength ASTM D790 psi 30,000 10,000
Flexural modulus ASTM D790 psi x 10⁶ 1.6 0.8
Izod impact ASTM D256 ft.-lbs/in 25 4
Compressive strength ASTM D695 psi 30,000 15,000
Compressive modulus ASTM D695 psi x 10⁶ 2.5 1.0
Barcol hardness ASTM D2583 – 50 45
Shear strength ASTM D732 psi 5,500 5,500
Density ASTM D1505 lbs/in3 0.065 –
Coefficient of thermal expansion ASTM D696 in/in/°F 5.0 x 10-6 –
Water absorption ASTM D570 Max % 0.5 –
Dielectic strength ASTM D149 V/mil (vpm) 200 –
Flammability classification UL94 VO (both resins) – –
Flame spread ASTM E-84 20 Max (both resins) – –
T&B nonmetallic cable tray systems are manufactured from glass fiber-reinforced plastic shapes that meet the ASTM E-84 Class 1 flame rating and self-extinguishing
requirements of ASTM D-635. A surface veil is applied during pultrusion to ensure a resin-rich surface and ultraviolet resistance.

—
Table 1 – Typical properties of pultruded components gland

Avg. Extent
Properties Ignition Burning Rating of Burning
Flame resistance (FTMS 406-2023) 75 seconds 75 seconds – –
Intermittent flame test (HLT- 15) – – 100 –
Flammability test (ASTM D635) – 5 seconds – 15mm
 T E C H N I C A L I N F O R M AT I O N - C O R R O S I O N G U I D E B7

—
Technical information
Corrosion guide

The information shown in this corrosion guide is based on full immersion laboratory tests
and data generated from resin manufacturers. It should be noted that in some of the
environments listed, splashes and spills may result in a more corrosive situation than indicated
due to the evaporation of water. Regular wash down is recommended in these situations.

—
Chemical resistance

75°F 75°F
Chemical environment (24°C) 160F° (71°C) Chemical environment (24°C) 160F° (71°C)
Acetic Acid 5% FR-P FR-P Methyl Alcohol 10% FR-P FR-VE-150° (*)
Acetic Acid 25% FR-P FR-VE-210° (*) Naphtha FR-P FR-P
Aluminum Potassium Sulfate 5% FR-P FR-P Nitric Acid 5% FR-P FR-P
Ammonium Hydroxide 10% FR-P FR-VE-150° Nitric Acid 20% FR-VE FR-VE-120° (*)
Ammonium Nitrate FR-P FR-P Phosphoric Acid 10% FR-P FR-P
Benzenesulfonic Acid 5% FR-P FR-P Phosphoric Acid 30% FR-P FR-P
Calcium Chloride FR-P FR-P Phosphoric Acid 85% FR-P FR-P
Carbon Tetrachloride FR-VE FR-VE-100° (*) Sodium Bicarbonate 10% FR-P FR-P
Chlorine Dioxide 15% FR-P FR-VE-150° (*) Sodium Bisulfate FR-P FR-P
Chromic Acid 5% FR-P FR-VE-150° (*call) Sodium Carbonate FR-P FR-VE
Copper Sulfate FR-P FR-P Sodium Chloride FR-P FR-P
Diesel Fuel No. 1 FR-P FR-P Sodium Hydroxide 1-50% FR-VE FR-VE-120° (*)
Diesel Fuel No. 2 FR-P FR-P Sodium Hypochlorite 5% FR-P FR-VE-120° (*)
Ethylene Glycol FR-P FR-P Sodium Nitrate FR-P FR-P
Fatty Acids 100% FR-P FR-P Sodium Silicate FR-P FR-VE-210° (*)
Ferrous Sulfate FR-P FR-P Sodium Sulfate FR-P FR-P
Fluosilicic Acid 0-20% FR-VE FR-VE (call) Sulfuric Acid 0-30% FR-P FR-P
Hydrochloric Acid 1% FR-P FR-P Sulfuric Acid 30-50% FR-VE FR-VE
Hydrochloric Acid 15% FR-P FR-VE-180° (*) Sulfuric Acid 50-70% FR-VE FR-VE-180° (*)
Hydrochloric Acid 37% FR-P FR-VE-150° (*) Trisodium Phosphate 25% FR-P FR-VE-210° (*)
Hydrogen Sulfide FR-P-140° FR-VE-210° Trisodium Phosphate - All FR-VE FR-VE-210° (*)
Kerosene FR-P FR-P Water, Distilled FR-P FR-P
Magnesium Chloride FR-P FR-P
Symbols:
FRP - Polyester fire-retardant
FRVE - Vinyl Ester fire-retardant

All data represents the best available information and is believed to be correct. The data
should not be construed as a warranty of performance for that product as presented
in these tables. User tests should be performed to determine suitabiity of service if there
is any doubt or concern. Such variables as concentration, temperature, time of exposure
and combined chemical effects of mixtures of chemicals make it impossible to specify the
exact suitability of fiber-reinforced plastics in all environments. ABB
will be happy to supply material samples for testing. These recommendations should only
be used as a guide, and ABB does not take responsibility for design or suitability of
materials for service intended. In no event will ABB be liable for any consequential or
special damages for any defective material or workmanship including, without limitation,
labor charges or other expenses or damage to property
resulting from loss of materials or profits or increased expenses of operations.
B8 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Technical information
CSA and NEMA loading classes
The standard classes of cable trays, as related to their maximum design loads and to the
associated design support spacing based on a simple beam span requirement, shall
be designated in accordance with Table 1.

— Costs vary between different load classes.

Selection process Since labor and coupling costs are similar for
a given length of tray, the heavier classes are less
Please note the load ratings in Table 1 are those cost-effective on a load length basis. The designer
most commonly used. Other load ratings are should therefore specify the lightest class of
acceptable. (according to NEMA VE-1/CSA tray compatible with the weight requirements
C22.2 No 126.1-02). of the cable tray.

— —
Table 1 – Span/load class designation – USA Table 1 – Span/load class designation – CANADA

Load Span m (ft.) Load Span m (ft.)

kg/m (lb/ft.) 1.5 (5) 2.4 (8) 3.0 (10) 3.7 (12) 6.0 (20) kg/m (lb/ft) 1.5 (5) 2.0 (6.5) 2.5 (8.2) 3.0 (10) 4.0 (13) 5.0 (16.4) 6.0 (20)
37 (25) 5AA 8AA 10AA 12AA 20AA 37 (25) – – – A – – –
74 (50) 5A 8A 10A 12A 20A 45 (30) – – A – – – –
112 (75) – 8B – 12B 20B 62 (42) – A – – – – –
149 (100) – 8C – 12C 20C 67 (45) – – – – – – D
NOTE: These ratings are also used in Mexico. 82 (55) – – – – – D –
97 (65) – – – C – – –
99 (67) A – – – – – –
112 (75) – – – – – – E
113 (76) – – – – D – –
119 (80) – – C – – – –
137 (92) – – – – – E –
164 (110) – C – – – – –
179 (120) – – – D – – –
189 (127) – – – – E – –
259 (174) C – – – –
299 (200) – – – E – – –

Deflection

Span
T E C H N I C A L I N F O R M AT I O N - C S A A N D N E M A LO A D I N G C L A S S E S B9

— —
Loading capacity Concentrated loads
Cable loads A concentrated static load is not included in Table 1
The cable load is the total weight, expressed in (following page). Some user applications may
(lb/ft.), of all the cables that will be placed in require that a given concentrated static load be
the cable tray. imposed over and above the working load.

Snow loads Such a concentrated static load represents a static

Depending on the area, snowfall could indicate weight applied on the centerline of the tray at
an additional design load. If snowfall is a factor and midspan. When so specified, the concentrated
the tray has a solid cover in outdoor installations, static load may be converted to an equivalent
a minimum load of 5 lb (2.27kg). per square foot uniform load (We) in kilograms/meter (pounds),
should be used. using the following formula, and added to the
static weight of cable in the tray:
Ice loads
If a cable tray system is subject to icing conditions, We = 2 x (concentrated static load, kg (lb)
usually only the top surface or cover and the
windward side will be coated with any significant Span length, m (ft.)
amount. It is generally assumed that ice
weighs 57 lb (25.85kg) per cubic foot. This combined load may be used to select a
suitable load/span designation. If the combined
Wind loads load exceeds the working load shown on the
All outdoor cable tray installations should factor following page, the manufacturer should
in wind loads, especially the pressure exerted be consulted.
on side rails of ladder trays. There have also been
instances of strong winds lifting covers off trays,
—
which can be minimized with the use of Effect of temperature
wraparound cover clamps.
Strength properties of reinforced plastics are
reduced when continuously exposed to elevated
temperatures. Working loads shall be reduced
based on table 2.

—
Table 2 – Effect of temperature

Temperature Approximate % of strength

(oC) (oF) Isophthalic polyester Vinylester
23.8 75 100 100
37.7 100 90 100
51.6 125 78 100
65.5 150 68 90
79.4 175 60 90
93.3 200 52 75
NEMA Standard 8-10-1986.
If unusual temperature conditions exist, the manufacturer should be consulted.
B10 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Technical information
Thermal contraction and expansion
It is important that thermal contraction and expansion be considered when installing
cable tray systems. The length of the straight cable tray runs and the temperature
differential govern the number of expansion splice plates required (see Table 1 below).

—
01 Typical cable tray
The cable tray should be anchored at the support Accurate gap setting at the time of installation
installation nearest to its midpoint between the expansion is necessary for the proper operation of the
splice plates and secured by expansion guides at all expansion splice plates. The following procedure
other support locations (see diagram 01). The cable should assist the installer in determining the
tray should be permitted longitudinal movement in correct gap (see Figure 1):
both directions from that fixed point. 1. Plot the highest expected tray temperature on
the maximum temperature line.
2. Plot the lowest expected tray temperature on the
minimum temperature line.
Figure 1 - Proper gap settings
3. Draw a line between the maximum and
Max. Min. minimum points.
temp. °F
°F °F temp.
°F 4. Plot the tray temperature at the time of installa-
130 130
tion to determine the gap setting.

110 110
Tray temperature at time of installation

—
90 90 Table 1 - Expansion or contraction for various temperature differences
Tray temperature at time of installation

70 70
Max. distance between Max. distance between
Temperature expansion connector* expansion connector*
50 50
differential for 1" (25.4mm) expansion for 5⁄8" (15.9mm) expansion

30 30 oF oC (ft.) (m) (ft.) (m)

14 25 667 203.3 417 127.1
10 10
28 50 333 101.5 208 63.3

-10 -10 42 75 222 67.6 139 42.3

56 100 167 50.9 104 31.7
-30 83
70 125 133 40.5 25.2
83 150 111 33.8 69 21
1/8 1/4 3/8 1/2
97 175 95 28.9 59 17.9
NOTE: These ratings are also used in Mexico.
0 5/8
—
01

l = expansion guide clamp at support = hold-down clamp (anchor) at support

Expansion joint
 T E C H N I C A L I N F O R M AT I O N - I N S TA L L AT I O N G U I D E L I N E S B11

—
Technical information
Installation guidelines
Installation of T&B nonmetallic cable tray should be made in accordance with the
standards set by the NEMA VE2 publication and CSA standards.

Always observe common safety practices when Drill nonmetallic as you would drill hardwood.
assembling tray and fittings. Installations generally Standard twist drills are more than adequate.
require some field cutting. Dust created during Any surface that has been drilled, cut, sanded or
fabrication presents no serious health hazard, but otherwise broken must be sealed with a
skin irritation may be experienced by compatible resin. Carbide-tipped saw blades
some workers. and drill bits are recommended when cutting
large quantities.
Operators of saws and drills should wear masks,
long-sleeve shirts or coveralls. Support the nonmetallic cable tray material
firmly during cutting operations to keep material
Fabrication with nonmetallic cable tray is relatively from shifting, which may cause chipping at the
easy and comparable to working with wood. cut edge.
Ordinary hand tools may be used in most cases.
Each tray section length should be equal to or
Avoid excessive pressure when sawing or drilling. greater than the support span. When possible, the
Too much force can rapidly dull tools and also splice should be located at quarter span.
produce excessive heat, which softens the bonding
resin in the nonmetallic cable tray, resulting in a Fittings should be supported as per NEMA VE2.
ragged edge rather than a clean-cut edge.

Field cutting is simple and can be accomplished

with a circular power saw with an abrasive
cut-off wheel (masonry type) or hack saw
(24 to 32 teeth per inch).
B12 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Technical information
Cable tray support locations

Horizontal elbow Vertical elbow Horizontal tee

2 ft..
2 ft.

2/3R

ø
22 ft.
ft..
..
fftt

ø
22

1/22Øø
1/ 2/3L
1/2 L
2 2ft.
ft..

22ft.
ft.. 2 ft..
L

Horizontal wye Horizontal cross Horizontal reducer

22ft.
ft.. 2 ft.

2/3R
2/3R

2 ft. 2 ft.
2 ft.
2 ft. 2 ft.

2 ft. 2 ft.

2/3R
2/3R

—
*NOTE: ø = 30°, 45°, 60°,
90° (degree of fitting)
 F R P C A B L E T R AY S P E C I F I C AT I O N S - E X T E R N A L R E V I S I O N 1 B13

—
FRP Cable Tray specifications
External revision 1
—
*Dimension
— 3.05 Loading classifications and test specimens
Conversion Table:
2" = 50.8mm
Section 1 - Acceptable manufacturers shall be per CSA/NEMA.

3" = 76.2mm
4" = 101.6mm 1.01 Cable tray system will be made of straight 3.06 Rung spacing shall be 6, 9.25, 12 or 18.5" (*mm)
5" = 127mm
sections, fittings and accessories as defined
7" = 177.8mm
6" = 152.4mm in the latest CSA/NEMA standards publication.
—
8" = 203.2mm
9" = 228.6mm
Section 4 - Dimensions
9.25" = 235mm 1.02 All manufacturing practices will be in
12" = 304.8mm
accordance with CSA/NEMA. 4.01 All fittings shall be of mitered design type
18" = 355.6mm
18.5" = 470mm
with a minimum 3" (76.2mm) tangent
24" = 457.2mm
1.03 Cable trays will be by ABB, or following the radius.
30" = 762mm
36" = 914.4mm approved CSA/NEMA member.
42" = 1,066.8mm 4.02 All fittings shall have a nominal 9.25"
— rung spacing.
Section 2 - Cable tray design
4.03 Width (usable inside tray width) shall be
2.01 Straight section structural elements; side 6, 9, 12, 18, 24, 30 or 36" (*mm).
rails, rungs and splice plates shall be pultruded
from glass fiber reinforced polyester or 4.04 Outside width shall not exceed inside width
vinylester resin. by more than a total of 2" (50.8mm).

2.02 Pultruded shapes will be constructed with a 4.05 Straight and expansion splice plates will be of
surface veil to ensure a resin-rich and stainless steel or fiberglass design with an
ultravioletresistant surface. eight-bolt pattern in 5" (127mm) fill systems
and four-bolt pattern for 3, 4, 6 and 8"
2.03 Pultruded shapes shall meet the ASTM E-84 tray depths.
Class 1 flame rating and self-extinguishing
requirements of ASTM D-635. 4.06 Dimension tolerances will be per CSA/NEMA.

— 4.07 Cable tray must have integral connection

Section 3 - Construction between side rails and rungs consisting of
nonmetallic mechanical fasteners and
3.01 Straight section lengths will be 120" adhesive bonding.
(10 ft. (3.05m)) or 240" (20 ft. (6.10m)) standard.

3.02 Side rails will be inward “C” configuration and

be predrilled to accept splice plates.

3.03 Overall heights shall be 8, 6, 4 or 3" (*mm)

respectively.

3.04 Loading depths for cable tray systems

shall be 7, 5, 3 or 2" (*mm) as per CSA/NEMA
tolerances.
B14 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray
Straight lengths
—
Applications
Nonmetallic cable tray systems
Nonmetallic cable tray systems have been tested
and proven in the harsh environment of the
offshore oil and gas industry – subject to the
corrosive conditions inherent in petroleum products,
plus the daily punishment of exposure to wind,
weather and saltwater.

Nonmetallic cable tray systems have stood up to

these challenges.
 N O N M E TA L L I C - C A B L E T R AY S T R A I G H T L E N G T H S B15

— —
Selection guide Straight fittings number selection
1. Nonmetallic cable tray system. To order
2. Select the correct T&B series cable tray using To order a straight section of cable tray, select the
the load data for straight sections found on appropriate size and material from the charts
page B16-B20. below and place those symbols in the sequence
3. Select the resin required. Refer to corrosion shown to form the complete catalog number.
guide on page B7 of the technical information
section for the effect of environmental Example:
conditions on the desired material. For the • NM-4P0924-120 for
effective temperature range, see page B9 • 4" (101.6mm) side rail, polyester resin
of the same section. • 9" (228.6mm) rung spacing
4. Select the rung spacing required to properly • 24" (609.6mm) wide, 120" (10 ft. (36.58m)) length
support cables in tray.
5 Select the desired width in inches. NOTE: One pair of nonmetallic splice plates with
6 Select the straight section length in inches. SS6 hardware included with each length.
For other types of splice plates, see pages B38-B41.

NM - 4 P - 09 24 - 120

Cable tray system Series Material Width Length

Nonmetallic 3 Polyester resin P 6" (152.4mm) 06 10 ft. (3.05m) 120
4 Vinylester resin V 9" (228.6mm) 09 20 ft. (6.10m) 240
6B 12" (304.8mm) 12
H6C 18" (457.2mm) 18
8 Rung spacing 24" (609.6mm) 24
6" (152.4mm) 06 30" (762mm) 30
9.25" (235mm) 09 36" (914.4mm) 36
12" (304.8mm) 12
18.5" (470mm) 18

Series 3 cable tray does not have UL listing.

B16 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray straight lengths
3" (76.2mm) Straight sections - Series 3

Splice plates
One pair of nonmetallic splice plates with SS6
(316 stainless steel) hardware included.

Deflection factor: To calculate deflection at any

span length for lighter loads than listed, multiply
the load by the K factor. When trays are used
in continuous spans, the deflection of the tray is
reduced by as much as 50%.

Loading
• CSA load class: A/3M
• NEMA 8A

—
3" (76.2mm) Straight sections – Series 3: Loading - NEMA 8A

Support span ft. (m)

Safety 8'
Series Factor (2.4m)
Side rail height: 3" (76.2mm) 3 Load (lb)/ft.) 1.5 50
(113/16" (46.04mm) loading depth) Load (kg)/m) 1.5 74
Deflection (in.) 1.5 2.35
1" Deflection (mm) 1.5 59.69
K factor 1.5 0.0162
NEMA
113/16" Fill 3"

—
Straight section number selection

NM - 3 P - 09 24 - 120

Cable tray system Series Material Rung spacing Width Length

Nonmetallic NM 3 Polyester resin P 6" (152.4mm) 06 6" (152.4mm) 06 10 ft. (3.05m) 120
Vinylester resin V 9.25" (235mm) 09 9" (228.6mm) 09 20 ft. (6.10m) 240
12" (304.8mm) 12 12" (304.8mm) 12
18.5" (470mm) 18 18" (457.2mm) 18
24" (609.6mm) 24
30" (762mm) 30
36" (914.4mm) 36
Series 3 cable tray does not have UL listing.
 N O N M E TA L L I C - C A B L E T R AY S T R A I G H T L E N G T H S B17

—
Nonmetallic - Cable tray straight lengths
4" (101.6mm) Straight sections - Series 4

Splice plates
One pair of nonmetallic splice plates with SS6
(316 stainless steel) hardware included.

Deflection factor: To calculate deflection at any

span length for lighter loads than listed, multiply
the load by the K factor. When trays are used
in continuous spans, the deflection of the tray is
reduced by as much as 50%.

Loading
• CSA load class: D/3M
• NEMA 12C
• UL Listing load class C
—
4" (101.6mm) Straight sections – Series 4: Loading - NEMA 12C

Support span ft (m)

Safety 8' 10' 12'

Series Factor (2.4m) (3m) (3.7m)
Side rail height: 4" (101.6mm) 4 Load (lb)/ft.) 1.5 205 144 100
(23/4" (69.85mm) loading depth) Load (kg)/m) 1.5 303 214 148
Deflection (in.) 1.5 1.18 2.03 2.92
1 1/8"
Deflection (mm) 1.5 29.972 51.562 74.168
K factor 1.5 0.005 0.014 0.029
NEMA
23/4" Fill 4"

—
Straight section number selection

NM - 4 P - 09 24 - 120

Cable tray system Series Material Rung spacing Width Length

Nonmetallic NM 6C Polyester resin P 6" (152.4mm) 06 6" (152.4mm) 06 10 ft. (3.05m) 120
Vinylester resin V 9.25" (235mm) 09 9" (228.6mm) 09 20 ft. (6.10m) 240
12" (304.8mm) 12 12" (304.8mm) 12
18.5" (470mm) 18 18" (457.2mm) 18
24" (609.6mm) 24
30" (762mm) 30
36" (914.4mm) 36
B18 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray straight lengths
6" (152.4mm) Straight sections - Series 6

Splice plates
One pair of nonmetallic splice plates with
stainless hardware included.

Deflection factor: To calculate deflection at any

span length for lighter loads than listed, multiply
the load by the K factor. When trays are used
in continuous spans, the deflection of the tray is
reduced by as much as 50%.

Loading
• CSA load class: E/6M
• NEMA 20C
• UL Listing load class C
—
6" (152.4mm) Straight sections – Series 6B: Loading - NEMA 20C

Support span ft. (m)

Safety 14' 16' 18' 20'

Series Factor (4.3m) (4.9m) (5.5m) (6.1m)
Side rail height: 6" (152.4mm) 6B Load (lb)/ft.) 1.5 204 156 123 100
(43/4" (120.65mm) loading depth) Load (kg)/m) 1.5 304 233 184 149
1 5/8" Deflection (in.) 1.5 2.59 3.4 4.3 5.28
Deflection (mm) 1.5 86.36 86.36 109.22 134.112
K factor 1.5 0.0139 0.0237 0.038 0.058
NEMA
43/4" Fill 6"

—
Straight section number selection

NM - 6B P - 09 24 - 120

Cable tray system Series Material Rung spacing Width Length

Nonmetallic NM 6B Polyester resin P 6" (152.4mm) 06 6" (152.4mm) 06 10 ft. (3.05m) 120
Vinylester resin V 9.25" (235mm) 09 9" (228.6mm) 09 20 ft. (6.10m) 240
12" (304.8mm) 12 12" (304.8mm) 12
18.5" (470mm) 18 18" (457.2mm) 18
24" (609.6mm) 24
30" (762mm) 30
36" (914.4mm) 36
 N O N M E TA L L I C - C A B L E T R AY S T R A I G H T L E N G T H S B19

—
Nonmetallic - Cable tray straight lengths
6" (152.4mm) Straight sections - Series H6C

Splice plates
One pair of nonmetallic splice plates with SS6
(316 stainless steel) hardware included.

Deflection factor: To calculate deflection at any

span length for lighter loads than listed, multiply
the load by the K factor. When trays are used
in continuous spans, the deflection of the tray is
reduced by as much as 50%.

Loading
• CSA load class: E/6M
• NEMA 20C
• UL Listing load class C
—
6" (152.4mm) Straight sections – Series H6C: Loading - NEMA 20C

Support span ft. (m)

Safety 14' 16' 18' 20'

Series Factor (4.3m) (4.9m) (5.5m) (6.1m)
Side rail height: 6" (152.4mm) H6C Load (lb)/ft.) 1.5 272 208 164 133
(4 11/16" (119.1mm) loading depth) Load (kg)/m) 1.5 405 310 244 198
1 5/8" Deflection (in.) 1.5 3.64 4.76 6.01 7.45
Deflection (mm) 1.5 92.456 120.904 152.654 189.23
K factor 1.5 0.0129 0.022 0.0352 0.0536
NEMA
4 11/16" Fill 6"

—
Straight section number selection

NM - H6C P - 09 24 - 120

Cable tray system Series Material Rung spacing Width Length

Nonmetallic NM H6C Polyester resin P 6" (152.4mm) 06 6" (152.4mm) 06 10 ft. (3.05m) 120
Vinylester resin V 9.25" (235mm) 09 9" (228.6mm) 09 20 ft. (6.10m) 240
12" (304.8mm) 12 12" (304.8mm) 12
18.5" (470mm) 18 18" (457.2mm) 18
24" (609.6mm) 24
30" (762mm) 30
36" (914.4mm) 36
B20 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray straight lengths
8" (203.2mm) Straight sections - Series 8

Splice plates
One pair of nonmetallic splice plates with SS6
(316 stainless steel) hardware included.

Deflection factor: To calculate deflection at any

span length for lighter loads than listed, multiply
the load by the K factor. When trays are used
in continuous spans, the deflection of the tray is
reduced by as much as 50%.

Loading
• CSA load class: E/6M
• NEMA 20C
• UL Listing load class C
—
8" (203.2mm) Straight sections – Series 8: Loading - NEMA 20C

Support span ft. (m)

Safety 14' 16' 18' 20'

Series Factor (4.3m) (4.9m) (5.5m) (6.1m)
Side rail height: 8" (203.2mm) 8 Load (lb)/ft.) 1.5 204 156 123 100
(6 11/16" (119.1mm) loading depth) Load (kg)/m) 1.5 304 233 184 149
1 3/4" Deflection (in.) 1.5 2.03 3.47 5.47 7.02
Deflection (mm) 1.5 51.562 88.138 138.938 178.308
K factor 1.5 0.0057 0.0097 0.0155 0.0236
NEMA
6 11/16" Fill 8"

—
Straight section number selection

NM - 8 P - 09 24 - 120

Cable tray system Series Material Rung spacing Width Length

Nonmetallic NM 8 Polyester resin P 6" (152.4mm) 06 6" (152.4mm) 06 10 ft. (3.05m) 120
Vinylester resin V 9.25" (235mm) 09 9" (228.6mm) 09 20 ft. (6.10m) 240
12" (304.8mm) 12 12" (304.8mm) 12
18.5" (470mm) 18 18" (457.2mm) 18
24" (609.6mm) 24
30" (762mm) 30
36" (914.4mm) 36
 N O N M E TA L L I C - C A B L E T R AY S T R A I G H T L E N G T H S B21

—
Nonmetallic - Cable tray straight lengths
Marine rung & strut rung cable tray

Top view
1" 13/4"

1" Marine rung

Channel
1" Rung

1"
End view

23/4"
Channel

—
01

Isometric view Section view 1 15/8’’

5
⁄8 "
6" Channel
Strut

1" Rung
6’’ CHANNEL
6" Channel

RUNG PLUG
Rung plug NEMA
NEMA
45’’
11/16''
FILL Fill
6’’
6"
1’’Rung
1" RUNG

6" Channel
1/4" (rung
pin head
thickness)

—
02

—
01 Marine rung cable tray
— —
—
02 Strut rung cable tray
Marine rung cable tray Strut rung cable tray
• Meets U.S. Coast Guard requirements • Catalog Number: Add SR after rung spacing
• Catalog Number: Add MR after rung spacing • Call your ABB representative for documentation
• Example: NM-4P-09MR-24-120
• Call your ABB representative for documentation
B22 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S
 N O N M E TA L L I C - C A B L E T R AY F I T T I N G S B23

—
Nonmetallic - Cable tray
Fittings
— — —
NOTE: Splice plates NOT
included. See pages
B38-B41 for type of splice
Selection guide Straight fittings number selection
plates available.
Covers are available. 1. Nonmetallic cable tray system. To order
Please consult your ABB
representative.
2. For mitered fittings when available. To order a straight section of cable tray, select the
3. Select height of fitting required for application. appropriate size and material from the charts
This should match tray series and height selection. below and place those symbols in the sequence
4. Select the resin required. Refer to corrosion shown to form the complete catalog number.
guide on page B7 of the technical
information section for the effect of Example:
environmental conditions on the desired NM-4P0924-120
material; for the effective temperature range, • 4" (101.6mm) side rail, polyester resin
see page B9 of the same section. • 9" (228.6mm) rung spacing
5. Select the desired width in inches. • 24" (609.6mm) wide, 120" (10 ft.) length
6. Angle of fitting required for application.
7. Type of fitting required for application. NOTE: One pair of nonmetallic splice plates with
See choices below. SS6 hardware included with each length.
8. Radius required for application. This would be For other types of splice plates,
determined by allowable radius of cables being see pages B38-B41.
installed. Standard radius is 24" (609.6mm).

NM - M 4 - P - 09 - 90 - HB 24

Cable tray system Side rail height Material Type Radius

Nonmetallic NM 3" (76.2mm) 3* Polyester resin P Horizontal bend HB 12" (304.8mm) 12
4" (101.6mm) 4 Vinylester V Horizontal tee HT 24" (609.6mm) 24
6" (152.4mm) 6 Horizontal cross HX 36" (914.4mm) 36
8" (203.2mm) 8 Vertical inside bend VI
Vertical outside bend VO
Vertical tee VT
Mitered Width Angle Vertical tee, down VTD
When available M 6" (152.4mm) 06 30o Right reducer RR
9" (228.6mm) 09 45o Left reducer LR
12" (304.8mm) 12 60o Straight reducer SR
18" (457.2mm) 18 90o Cable support fitting CSF
24" (609.6mm) 24
30" (762mm) 30
36" (914.4mm) 36

*Series 3 cable tray does not have UL or CSA listing.

B24 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray fittings
3" (76.2mm), 4" (101.6mm), 6" (152.4mm) & 8" (203.2mm) - 90o Horizontal bend fittings

—
90o Horizontal bend

Bend radius (R) Tray width (W) Dimensions

(in.) (mm) (in.) (mm) Cat. No. A (in.) A (mm) L (in.) L (mm)
12 304.8 6 152.4 NM-M(*)-(Matl)-06-90HB12 335⁄8 854 471⁄2 1,207
12 304.8 9 228.6 NM-M(*)-(Matl)-09-90HB12 365/8 930 513/4 1,314
12 304.8 12 304.8 NM-M(*)-(Matl)-12-90HB12 395/8 1,006 56 1,422

L 12 304.8 18 457.2 NM-M(*)-(Matl)-18-90HB12 455/8 1,159 641/2 1,638

12 304.8 24 609.6 NM-M(*)-(Matl)-24-90HB12 515/8 1,311 73 1,854
12 304.8 30 762 NM-M(*)-(Matl)-30-90HB12 575/8 1,464 811/2 2,070
12 304.8 36 914.4 NM-M(*)-(Matl)-36-90HB12 635/8 1,616 90 2,286
R 24 609.6 6 152.4 NM-M(*)-(Matl)-06-90HB24 4 55⁄8 1,159 641⁄2 1,638
R 24 609.6 9 228.6 NM-M(*)-(Matl)-09-90HB24 485/8 1,235 683/4 1,746
W
A 24 609.6 12 304.8 NM-M(*)-(Matl)-12-90HB24 515/8 1,311 73 1,854
24 609.6 18 457.2 NM-M(*)-(Matl)-18-90HB24 575/8 1,464 811/2 2,070
24 609.6 24 609.6 NM-M(*)-(Matl)-24-90HB24 635/8 1,616 90 2,286
24 609.6 30 762 NM-M(*)-(Matl)-30-90HB24 695/8 1,768 981/2 2,502
24 609.6 36 914.4 NM-M(*)-(Matl)-36-90HB24 755/8 1,921 107 2,718
36 914.4 6 152.4 NM-M(*)-(Matl)-06-90HB36 575⁄8 1,464 811⁄2 2,070
36 914.4 9 228.6 NM-M(*)-(Matl)-09-90HB36 605/8 1,540 853/4 2,178
36 914.4 12 304.8 NM-M(*)-(Matl)-12-90HB36 635/8 1,616 90 2,286
36 914.4 18 457.2 NM-M(*)-(Matl)-18-90HB36 695/8 1,768 981/2 2,502
36 914.4 24 609.6 NM-M(*)-(Matl)-24-90HB36 755/8 1,921 107 2,718
36 914.4 30 762 NM-M(*)-(Matl)-30-90HB36 815/8 2,073 1155/8 2,931
36 914.4 36 914.4 NM-M(*)-(Matl)-36-90HB36 875/8 2,226 1237/8 3,146
(*) Side Rail Height. One pair of fiberglass splice plates with SS6 hardware included.
Dimensions for reference only; when critical, contact your ABB representative. Consult your ABB representative for availability of molded fittings.
Standard rung spacing for fittings is 91/4" nominal (235mm). For other types of splice plates, see pages B38-B41.

—
Fitting number selection

NM - M 4 - P - 24 - 90 - HB 12

Nonmetallic Mitered Height Material Width Angle Type Radius

 N O N M E TA L L I C - C A B L E T R AY F I T T I N G S B25

—
Nonmetallic - Cable tray fittings
3" (76.2mm), 4" (101.6mm), 6" (152.4mm) & 8" (203.2mm) - 45o Horizontal bend fittings

—
45o Horizontal bend

Bend radius (R) Tray width (W) Dimensions

(in.) (mm) (in.) (mm) Cat. No. A (in.) A (mm) L (in.) L (mm)
12 304.8 6 152.4 NM-M(*)-(Matl)-06-45HB12 2011/16 525 387/8 987
12 304.8 9 228.6 NM-M(*)-(Matl)-09-45HB12 2311/16 602 41 1,041
12 304.8 12 304.8 NM-M(*)-(Matl)-12-45HB12 2611/16 678 431/8 1,095
12 304.8 18 457.2 NM-M(*)-(Matl)-18-45HB12 3211/16 830 473/8 1,203

L 12 304.8 24 609.6 NM-M(*)-(Matl)-24-45HB12 3811/16 983 515/8 1,311

R 12 304.8 30 762 NM-M(*)-(Matl)-30-45HB12 4411/16 1,135 557/8 1,419

12 304.8 36 914.4 NM-M(*)-(Matl)-36-45HB12 5011/16 1,287 601/8 1,527
R 24 609.6 6 152.4 NM-M(*)-(Matl)-06-45HB24 241/4 616 473/8 1,203
24 609.6 9 228.6 NM-M(*)-(Matl)-09-45HB24 271/4 692 491/2 1,257
24 609.6 12 304.8 NM-M(*)-(Matl)-12-45HB24 301/4 768 515/8 1,311
W
A 24 609.6 18 457.2 NM-M(*)-(Matl)-18-45HB24 361/4 921 557/8 1,419
24 609.6 24 609.6 NM-M(*)-(Matl)-24-45HB24 421/4 1,073 601/8 1,527
24 609.6 30 762 NM-M(*)-(Matl)-30-45HB24 481/4 1,226 643/8 1,635
24 609.6 36 914.4 NM-M(*)-(Matl)-36-45HB24 541/4 1,378 685/8 1,743
36 914.4 6 152.4 NM-M(*)-(Matl)-06-45HB36 273/4 705 557/8 1,419
36 914.4 9 228.6 NM-M(*)-(Matl)-09-45HB36 303/4 781 58 1,473
36 914.4 12 304.8 NM-M(*)-(Matl)-12-45HB36 333/4 857 601/8 1,527
36 914.4 18 457.2 NM-M(*)-(Matl)-18-45HB36 393/4 1,010 643/8 1,635
36 914.4 24 609.6 NM-M(*)-(Matl)-24-45HB36 453/4 1,162 685/8 1,743
36 914.4 30 762 NM-M(*)-(Matl)-30-45HB36 513/4 1,314 7213/16 1,846
36 914.4 36 914.4 NM-M(*)-(Matl)-36-45HB36 573/4 1,467 771/16 1,957
(*) Side Rail Height. One pair of fiberglass splice plates with SS6 hardware included.
Dimensions for reference only; when critical, contact your ABB representative. Consult your ABB representative for availability of molded fittings.
Standard rung spacing for fittings is 91/4" nominal (235mm). For other types of splice plates, see pages B38-B41.

—
Fitting number selection

NM - M 4 - P - 24 - 45 - HB 12

Nonmetallic Mitered Height Material Width Angle Type Radius

B26 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray fittings
3" (76.2mm), 4" (101.6mm), 6" (152.4mm) & 8" (203.2mm) - Horizontal tee fittings

—
Horizontal tee

Bend radius (R) Tray width (W) Dimensions

(in.) (mm) (in.) (mm) Cat. No. A (in.) A (mm) L (in.) L (mm)
12 304.8 6 152.4 NM-M(*)-(Matl)-06-HT12 305/8 780 551/2 1,410
B
12 304.8 9 228.6 NM-M(*)-(Matl)-09-HT12 335/8 850 551/2 1,410

W 12 304.8 12 304.8 NM-M(*)-(Matl)-12-HT12 365/8 930 551/2 1,410

R 12 304.8 18 457.2 NM-M(*)-(Matl)-18-HT12 425/8 1,080 643/4 1,640
A R
R 12 304.8 24 609.6 NM-M(*)-(Matl)-24-HT12 485/8 1,240 74 1,880

W 12 304.8 30 762 NM-M(*)-(Matl)-30-HT12 545/8 1,390 74 1,880

W 12 304.8 36 914.4 NM-M(*)-(Matl)-36-HT12 605/8 1,540 831/4 2,110
A
24 609.6 6 152.4 NM-M(*)-(Matl)-06-HT24 425/8 1,080 74 1,880
24 609.6 9 228.6 NM-M(*)-(Matl)-09-HT24 455/8 1,160 831/4 2,110
24 609.6 12 304.8 NM-M(*)-(Matl)-12-HT24 485/8 1,240 831/4 2,110
24 609.6 18 457.2 NM-M(*)-(Matl)-18-HT24 545/8 1,390 921/2 2,350
24 609.6 24 609.6 NM-M(*)-(Matl)-24-HT24 605/8 1,540 921/2 2,350
24 609.6 30 762 NM-M(*)-(Matl)-30-HT24 665/8 1,690 1013/4 2,580
24 609.6 36 914.4 NM-M(*)-(Matl)-36-HT24 725/8 1,840 111 2,820
36 914.4 6 152.4 NM-M(*)-(Matl)-06-HT36 545/8 1,390 1013/4 2,580
36 914.4 9 228.6 NM-M(*)-(Matl)-09-HT36 575/8 1,460 1013/4 2,580
36 914.4 12 304.8 NM-M(*)-(Matl)-12-HT36 605/8 1,540 111 2,820
36 914.4 18 457.2 NM-M(*)-(Matl)-18-HT36 665/8 1,690 111 2,820
36 914.4 24 609.6 NM-M(*)-(Matl)-24-HT36 725/8 1,840 1201/4 3,050
36 914.4 30 762 NM-M(*)-(Matl)-30-HT36 785/8 2,000 1291/2 3,290
36 914.4 36 914.4 NM-M(*)-(Matl)-36-HT36 845/8 2,150 1291/2 3,290
(*) Side Rail Height. Two pairs of fiberglass splice plates with SS6 hardware included.
Dimensions for reference only; when critical, contact your ABB representative. Consult your ABB representative for availability of molded fittings.
Standard rung spacing for fittings is 91/4" nominal (235mm). For other types of splice plates, see pages B38-B41.

—
Fitting number selection

NM - M 4 - P - 24 - HT 12

Nonmetallic Mitered Height Material Width Type Radius

 N O N M E TA L L I C - C A B L E T R AY F I T T I N G S B27

—
Nonmetallic - Cable tray fittings
3" (76.2mm), 4" (101.6mm), 6" (152.4mm) & 8" (203.2mm) - Horizontal cross fittings

—
Horizontal cross

Bend radius (R) Tray width (W) Dimensions

(in.) (mm) (in.) (mm) Cat. No. A (in.) A (mm) L (in.) L (mm)
12 304.8 6 152.4 NM-M(*)-(Matl)-06-HX12 543/4 1,390 551/2 1,410
12 304.8 9 228.6 NM-M(*)-(Matl)-09-HX12 573/4 1,470 551/2 1,410
R 12 304.8 12 304.8 NM-M(*)-(Matl)-12-HX12 603/4 1,540 551/2 1,410
R 12 304.8 18 457.2 NM-M(*)-(Matl)-18-HX12 663/4 1,700 643/4 1,640

W W 12 304.8 24 609.6 NM-M(*)-(Matl)-24-HX12 723/4 1,850 74 1,880

L A 12 304.8 30 762 NM-M(*)-(Matl)-30-HX12 783/4 2,000 74 1,880
12 304.8 36 914.4 NM-M(*)-(Matl)-36-HX12 843/4 2,150 831/4 2,110
24 609.6 6 152.4 NM-M(*)-(Matl)-06-HX24 783/4 2,000 74 1,880
24 609.6 9 228.6 NM-M(*)-(Matl)-09-HX24 813/4 2,080 831/4 2,110
24 609.6 12 304.8 NM-M(*)-(Matl)-12-HX24 843/4 2,150 831/4 2,110
24 609.6 18 457.2 NM-M(*)-(Matl)-18-HX24 903/4 2,310 921/2 2,350
24 609.6 24 609.6 NM-M(*)-(Matl)-24-HX24 963/4 2,460 921/2 2,350
24 609.6 30 762 NM-M(*)-(Matl)-30-HX24 1023/4 2,610 1013/4 2,580
24 609.6 36 914.4 NM-M(*)-(Matl)-36-HX24 1083/4 2,760 111 2,820
36 914.4 6 152.4 NM-M(*)-(Matl)-06-HX36 1023/4 2,610 1013/4 2,580
36 914.4 9 228.6 NM-M(*)-(Matl)-09-HX36 1053/4 2,690 1013/4 2,580
36 914.4 12 304.8 NM-M(*)-(Matl)-12-HX36 1083/4 2,760 111 2,820
36 914.4 18 457.2 NM-M(*)-(Matl)-18-HX36 1153/4 2,914 111 2,820
36 914.4 24 609.6 NM-M(*)-(Matl)-24-HX36 1203/4 3,070 1201/4 3,050
36 914.4 30 762 NM-M(*)-(Matl)-30-HX36 1263/4 3,220 1291/2 3,290
36 914.4 36 914.4 NM-M(*)-(Matl)-36-HX36 1323/4 3,370 1291/2 3,290
(*) Side Rail Height. Three pairs of fiberglass splice plates with SS6 hardware included.
Dimensions for reference only; when critical, contact your ABB representative. Consult your ABB representative for availability of molded fittings.
Standard rung spacing for fittings is 91/4" nominal (235mm). For other types of splice plates, see pages B38-B41.

—
Fitting number selection

NM - M 4 - P - 24 - HX 12

Nonmetallic Mitered Height Material Width Type Radius

B28 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray fittings
3" (76.2mm), 4" (101.6mm), 6" (152.4mm) & 8" (203.2mm) - Horizontal reducer fittings

—
Horizontal reducer - 4" (101.6mm)

Tray widths
W1 W2 Left-hand reducer Dim. Dim. Straight reducer Dim. Dim. Right-hand reducer Dim. Dim.
(in.) (mm) (in.) (mm) Cat. No. A (in.) L (mm) Cat. No. A (in.) L (mm) Cat. No. A (in.) L (mm)
9 228.6 6 152.4 NM-M(*)-(Matl)-09-LR06 273⁄4 705 NM-M(*)-(Matl)-09-SR06 263⁄8 670 NM-M(*)-(Matl)-09-RR06 273⁄4 705
12 304.8 6 152.4 NM-M(*)-(Matl)-12-LR06 37 940 NM-M(*)-(Matl)-12-SR06 263⁄4 679 NM-M(*)-(Matl)-12-RR06 37 940
12 304.8 9 228.6 NM-M(*)-(Matl)-12-LR09 273⁄4 705 NM-M(*)-(Matl)-12-SR09 263⁄8 670 NM-M(*)-(Matl)-12-RR09 273⁄4 705
18 457.2 6 152.4 NM-M(*)-(Matl)-18-LR06 37 940 NM-M(*)-(Matl)-18-SR06 341⁄2 876 NM-M(*)-(Matl)-18-RR06 37 940
18 457.2 9 228.6 NM-M(*)-(Matl)-18-LR09 37 940 NM-M(*)-(Matl)-18-SR09 33 838 NM-M(*)-(Matl)-18-RR09 37 940
18 457.2 12 304.8 NM-M(*)-(Matl)-18-LR12 273⁄4 705 NM-M(*)-(Matl)-18-SR12 263⁄4 679 NM-M(*)-(Matl)-18-RR12 273⁄4 705
24 609.6 6 152.4 NM-M(*)-(Matl)-24-LR06 461⁄4 1,175 NM-M(*)-(Matl)-24-SR06 371⁄2 953 NM-M(*)-(Matl)-24-RR06 461⁄4 1,175
24 609.6 9 228.6 NM-M(*)-(Matl)-24-LR09 37 940 NM-M(*)-(Matl)-24-SR09 36 914 NM-M(*)-(Matl)-24-RR09 37 940
24 609.6 12 304.8 NM-M(*)-(Matl)-24-LR12 37 940 NM-M(*)-(Matl)-24-SR12 36 914 NM-M(*)-(Matl)-24-RR12 37 940
24 609.6 18 457.2 NM-M(*)-(Matl)-24-LR18 273⁄4 705 NM-M(*)-(Matl)-24-SR18 263⁄4 679 NM-M(*)-(Matl)-24-RR18 273⁄4 705
30 762 6 152.4 NM-M(*)-(Matl)-30-LR06 461⁄4 1,175 NM-M(*)-(Matl)-30-SR06 401⁄2 1,029 NM-M(*)-(Matl)-24-RR06 461⁄4 1,175
30 762 9 228.6 NM-M(*)-(Matl)-30-LR09 461⁄4 1,175 NM-M(*)-(Matl)-30-SR09 39 991 NM-M(*)-(Matl)-24-RR09 461⁄4 1,175
30 762 12 304.8 NM-M(*)-(Matl)-30-LR12 37 940 NM-M(*)-(Matl)-30-SR12 371⁄2 953 NM-M(*)-(Matl)-24-RR12 37 940
30 762 18 457.2 NM-M(*)-(Matl)-30-LR18 37 940 NM-M(*)-(Matl)-30-SR18 353⁄4 908 NM-M(*)-(Matl)-24-RR18 37 940
30 762 24 152.4 NM-M(*)-(Matl)-30-LR24 273⁄4 705 NM-M(*)-(Matl)-30-SR24 263⁄4 679 NM-M(*)-(Matl)-18-RR24 273⁄4 705
36 914.4 6 152.4 NM-M(*)-(Matl)-36-LR06 551⁄2 1,410 NM-M(*)-(Matl)-36-SR06 431⁄2 1,105 NM-M(*)-(Matl)-36-RR06 551⁄2 1,410
36 914.4 9 228.6 NM-M(*)-(Matl)-36-LR09 461⁄4 1,175 NM-M(*)-(Matl)-36-SR09 42 1,067 NM-M(*)-(Matl)-36-RR09 461⁄4 1,175
36 914.4 12 304.8 NM-M(*)-(Matl)-36-LR12 461⁄4 1,175 NM-M(*)-(Matl)-36-SR12 401⁄2 1,029 NM-M(*)-(Matl)-36-RR12 461⁄4 1,175
36 914.4 18 457.2 NM-M(*)-(Matl)-36-LR18 37 940 NM-M(*)-(Matl)-36-SR18 371⁄2 953 NM-M(*)-(Matl)-36-RR18 37 940
36 914.4 24 609.6 NM-M(*)-(Matl)-36-LR24 37 940 NM-M(*)-(Matl)-36-SR24 353⁄4 908 NM-M(*)-(Matl)-36-RR24 37 940
36 914.4 30 762 NM-M(*)-(Matl)-36-LR30 273⁄4 705 NM-M(*)-(Matl)-36-SR30 263⁄4 679 NM-M(*)-(Matl)-36-RR30 273⁄4 705
(*) Side Rail Height. One pair of fiberglass splice plates with SS6 hardware included. Dimensions for reference only; when critical, contact your ABB representative.
Consult your ABB representative for availability of molded fittings. Standard rung spacing for fittings is 91/4" nominal (235mm).
For other types of splice plates, see pages B38-B41.

Dimensions (4" & 6")

Left-hand reducer Straight reducer Right hand reducer

W₁ W₁ W₁

L L
L
W₂ W₂
W₂

—
Fitting number selection

NM - M 4 - P - 24 - LR 12

Nonmetallic Mitered Height Material Width 1 Type Width 2

 N O N M E TA L L I C - C A B L E T R AY F I T T I N G S B29

—
Nonmetallic - Cable tray fittings
3" (76.2mm), 4" (101.6mm), 6" (152.4mm) & 8" (203.2mm) - Horizontal reducing tee fittings

—
Horizontal reducing tee – 12" (304.8mm) radius

Tray width (W1) Tray width (W2) 12" (304.8mm) Radius

(in.) (mm) (in.) (mm) Cat. No. A (in.) A (mm) L (in.) L (mm)
9 228.6 6 152.4 NM-M(*)-(Matl)-06-06-HT12 305/8 777.87 551/2 1,409.7
L
12 304.8 6 152.4 NM-M(*)-(Matl)-09-06-HT12 335/8 854.07 551/2 1,409.7
12 304.8 9 228.6 NM-M(*)-(Matl)-09-09-HT12 335/8 854.07 551/2 1,409.7
W₁
18 457.2 6 152.4 NM-M(*)-(Matl)-12-06-HT12 365/8 930.27 551/2 1,409.7
A
R 18 457.2 9 228.6 NM-M(*)-(Matl)-12-09-HT12 365/8 930.27 551/2 1,409.7
18 457.2 12 304.8 NM-M(*)-(Matl)-12-12-HT12 365/8 930.27 551/2 1,409.7

W₂

(*) Side Rail Height. Two pairs of fiberglass splice plates with SS6 hardware included.
Dimensions for reference only; when critical, contact your ABB representative. Consult your ABB representative for availability of molded fittings.
Standard rung spacing for fittings is 91/4" nominal (235mm). For other types of splice plates, see pages B38-B41.

—
Horizontal reducing tee – 24" (609.6mm) & 36" (914.4mm) radius

Tray width (W1) Tray width (W2) 24" (609.6mm) Radius 36" (914.4mm) Radius
Cat. No.
(in.) (mm) (in.) (mm) (**) Insert radius 24" or 36" A (in.) A (mm) L (in.) L (mm) A (in.) A (mm) L (in.) L (mm)
9 228.6 6 152.4 NM-M(*)-(Matl)-06-06-HT(**) 425/8 1,082.55 74 1,879.6 545/8 1,387.35 1013/4 2,584.45
12 304.8 6 152.4 NM-M(*)-(Matl)-09-06-HT(**) 455/8 1,158.87 74 1,879.6 575/8 1,463.55 1013/4 2,584.45
12 304.8 9 228.6 NM-M(*)-(Matl)-09-09-HT(**) 455/8 1,158.87 831/4 2,114.55 575/8 1,463.55 1013/4 2,584.45
18 457.2 6 152.4 NM-M(*)-(Matl)-12-06-HT(**) 485/8 1,235.07 74 1,879.6 605/8 1,540.00 1013/4 2,584.45
18 457.2 9 228.6 NM-M(*)-(Matl)-12-09-HT(**) 485/8 1,235.07 831/4 2,114.55 605/8 1,540.00 1013/4 2,584.45
18 457.2 12 304.8 NM-M(*)-(Matl)-12-12-HT(**) 485/8 1,235.07 831/4 2,114.55 605/8 1,540.00 111 2,819.4
(*) Side Rail Height. (**) NOTE: Insert radius, 24" (609.6mm) or 36" (914.4mm). Two pairs of fiberglass splice plates with SS6 hardware included.
Dimensions for reference only; when critical, contact your ABB representative. Consult your ABB representative for availability of molded fittings.
Standard rung spacing for fittings is 91/4" nominal (235mm). For other types of splice plates, see pages B38-B41.

Sample mitered fitting

—
Fitting number selection

NM - M 4 - P - 24 - 12 - HT 12

Nonmetallic Mitered Height Material Width 1 Width 2 Type Radius

B30 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray fittings
3" (76.2mm), 4" (101.6mm), 6" (152.4mm) & 8" (203.2mm) - Horizontal expanding tee fittings

—
Horizontal expanding tee – 12" (304.8mm) & 24" (609.6mm) radius

Tray width (W1) Tray width (W2) 12" (304.8mm) Radius 24" (609.6mm) Radius
Cat. No.
(in.) (mm) (in.) (mm) (**) Insert radius 12" or 24" A (in.) A (mm) B (in.) B (mm) A (in.) A (mm) B (in.) B (mm)
9 228.6 12 304.8 NM-M(*)-(Matl)-09-12-HT(**) 335/8 854 551/2 1,410 455/8 1,159 831/4 2,115
9 228.6 18 457.2 NM-M(*)-(Matl)-09-18-HT(**) 335/8 854 643/4 1,645 455/8 1,159 921/2 2,350
9 228.6 24 609.6 NM-M(*)-(Matl)-09-24-HT(**) 335/8 854 74 1,880 455/8 1,159 921/2 2,350
9 228.6 30 762 NM-M(*)-(Matl)-09-30-HT(**) 335/8 854 74 1,880 455/8 1,159 1013/4 2,584
9 228.6 36 914.4 NM-M(*)-(Matl)-09-36-HT(**) 335/8 854 831/4 2,115 455/8 1,159 111 2,819
12 304.8 18 457.2 NM-M(*)-(Matl)-12-18-HT(**) 365/8 930 643/4 1,645 485/8 1,235 921/2 2,350
12 304.8 24 609.6 NM-M(*)-(Matl)-12-24-HT(**) 365/8 930 74 1,880 485/8 1,235 921/2 2,350
12 304.8 30 762 NM-M(*)-(Matl)-12-30-HT(**) 365/8 930 74 1,880 485/8 1,235 1013/4 2,584
12 304.8 36 914.4 NM-M(*)-(Matl)-12-36-HT(**) 365/8 930 831/4 2,115 485/8 1,235 111 2,819
18 457.2 24 609.6 NM-M(*)-(Matl)-18-24-HT(**) 425/8 1,083 74 1,880 545/8 1,387 921/2 2,350
18 457.2 30 762 NM-M(*)-(Matl)-18-30-HT(**) 425/8 1,083 74 1,880 545/8 1,387 1013/4 2,584
18 457.2 36 914.4 NM-M(*)-(Matl)-18-36-HT(**) 425/8 1,083 831/4 2,115 545/8 1,387 111 2,819
24 609.6 30 762 NM-M(*)-(Matl)-24-30-HT(**) 485/8 1,235 74 1,880 605/8 1,540 1013/4 2,584
24 609.6 36 914.4 NM-M(*)-(Matl)-24-36-HT(**) 485/8 1,235 831/4 2,115 605/8 1,540 111 2,819
30 762 36 914.4 NM-M(*)-(Matl)-30-36-HT(**) 545/8 1,387 831/4 2,115 665/8 1,692 111 2,819
(*) Side Rail Height. * NOTE: Insert radius, 12" (304.8mm) or 24" (609.6mm). Two pairs of fiberglass splice plates with SS6 hardware included.
Dimensions for reference only; when critical, contact your ABB representative. Consult your ABB representative for availability of molded fittings.
Standard rung spacing for fittings is 9" (228.6mm). For other types of splice plates, see pages B38-B41.

Dimensions Sample mitered fitting

B

W₁
A R

W₂

—
Fitting number selection

NM - M 4 - P - 12 - 24 - HT 12

Nonmetallic Mitered Height Material Width 1 Width 2 Type Radius

 N O N M E TA L L I C - C A B L E T R AY F I T T I N G S B31

—
Nonmetallic - Cable tray fittings
3" (76.2mm), 4" (101.6mm), 6" (152.4mm) & 8" (203.2mm) - Horizontal expanding tee fittings

—
Horizontal expanding tee – 36" (914.4mm) radius

Tray width (W1) Tray width (W2) 36" (914.4mm) Radius

(in.) (mm) (in.) (mm) Cat. No. A (in.) A (mm) B (in.) B (mm)
9 228.6 12 304.8 NM-M(*)-(Matl)-09-12-HT36 575/8 1,464 111 2,819
B 18 457.2 NM-M(*)-(Matl)-09-18-HT36 575/8 1,464 111 2,819
9 228.6
W₁ 9 228.6 24 609.6 NM-M(*)-(Matl)-09-24-HT36 575/8 1,464 1201/4 3,054

A R 9 228.6 30 609.6 NM-M(*)-(Matl)-09-30-HT36 575/8 1,464 1291/2 3,289

9 228.6 36 762 NM-M(*)-(Matl)-09-36-HT36 575/8 1,464 1291/2 3,289

W₂ 12 304.8 18 457.2 NM-M(*)-(Matl)-12-18-HT36 605/8 1,540 111 2,819

12 304.8 24 609.6 NM-M(*)-(Matl)-12-24-HT36 605/8 1,540 1201/4 3,054
12 304.8 30 609.6 NM-M(*)-(Matl)-12-30-HT36 605/8 1,540 1291/2 3,289
12 304.8 36 762 NM-M(*)-(Matl)-12-36-HT36 605/8 1,540 1291/2 3,289
18 457.2 24 609.6 NM-M(*)-(Matl)-18-24-HT36 665/8 1,692 1201/4 3,054
18 457.2 30 609.6 NM-M(*)-(Matl)-18-30-HT36 665/8 1,692 1291/2 3,289
18 457.2 36 762 NM-M(*)-(Matl)-18-36-HT36 665/8 1,692 1291/2 3,289
24 609.6 30 609.6 NM-M(*)-(Matl)-24-30-HT36 725/8 1,845 1291/2 3,289
24 609.6 36 762 NM-M(*)-(Matl)-24-36-HT36 725/8 1,845 1291/2 3,289
30 762 36 762 NM-M(*)-(Matl)-30-36-HT36 785/8 1,997 1291/2 3,289
(*) Side Rail Height. Two pairs of stainless steel SS6 splice plates with SS6 hardware included.
Dimensions for reference only; when critical, contact your ABB representative. Consult your ABB representative for availability of molded fittings.
Standard rung spacing for fittings is 9" (228.6mm). For other types of splice plates, see pages B38-B41.

Sample mitered fitting

—
Fitting number selection

NM - M 4 - P - 24 - 12 - HT 36

Nonmetallic Mitered Height Material Width 1 Width 2 Type Radius

B32 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray fittings
3" (76.2mm), 4" (101.6mm), 6" (152.4mm) & 8" (203.2mm) - Horizontal expanding/
reducing cross fittings
—
Horizontal expanding/reducing cross – 12" (304.8mm) & 24" (609.6mm) radius

Tray width (W1) Tray width (W2) 12" (304.8mm) Radius 24" (609.6mm) Radius
Cat. No.
(in.) (mm) (in.) (mm) *Insert radius (12" or 24") A (in.) A (mm) B (in.) B (mm) A (in.) A (mm) B (in.) B (mm)
6 152.4 9 228.6 NM-M(*)-(Matl)-06-09-HX* 543/4 1,391 551/2 1,410 783/4 2,000 831/4 2,115
6 152.4 12 304.8 NM-M(*)-(Matl)-06-12-HX* 543/4 1,391 551/2 1,410 783/4 4,972 831/4 2,115
6 152.4 18 457.2 NM-M(*)-(Matl)-06-18-HX* 543/4 1,391 643/4 1,645 783/4 2,000 921/2 2,350
6 152.4 24 609.6 NM-M(*)-(Matl)-06-24-HX* 543/4 1,391 74 1,880 783/4 2,000 921/2 2,350
6 152.4 30 762 NM-M(*)-(Matl)-06-30-HX* 543/4 1,391 74 1,880 783/4 2,000 1013/4 2,584
6 152.4 36 914.4 NM-M(*)-(Matl)-06-36-HX* 543/4 1,391 831/4 2,115 783/4 2,000 111 2,819
9 228.6 12 304.8 NM-M(*)-(Matl)-09-12-HX* 573/4 1,467 551/2 1,410 813/4 2,076 831/4 2,115
9 228.6 18 457.2 NM-M(*)-(Matl)-09-18-HX* 573/4 1,467 643/4 1,645 813/4 2,076 921/2 2,350
9 228.6 24 609.6 NM-M(*)-(Matl)-09-24-HX* 573/4 1,467 74 1,880 813/4 2,076 921/2 2,350
9 228.6 30 762 NM-M(*)-(Matl)-09-30-HX* 573/4 1,467 74 1,880 813/4 2,076 1013/4 2,584
9 228.6 36 914.4 NM-M(*)-(Matl)-09-36-HX* 573/4 1,467 831/4 2,115 813/4 2,076 111 2,819
12 304.8 18 457.2 NM-M(*)-(Matl)-12-18-HX* 603/4 1,543 643/4 1,645 843/4 2,153 921/2 2,350
12 304.8 24 609.6 NM-M(*)-(Matl)-12-24-HX* 603/4 1,543 74 1,880 843/4 2,153 921/2 2,350
12 304.8 30 762 NM-M(*)-(Matl)-12-30-HX* 603/4 1,543 74 1,880 843/4 2,153 1013/4 2,584
12 304.8 36 914.4 NM-M(*)-(Matl)-12-36-HX* 603/4 1,543 831/4 2,115 843/4 2,153 111 2,819
18 457.2 24 609.6 NM-M(*)-(Matl)-18-24-HX* 663/4 1,695 74 1,880 903/4 2,305 921/2 2,350
18 457.2 30 762 NM-M(*)-(Matl)-18-30-HX* 663/4 1,695 74 1,880 903/4 2,305 1013/4 2,584
18 457.2 36 914.4 NM-M(*)-(Matl)-18-36-HX* 663/4 1,695 831/4 2,115 903/4 2,305 111 2,819
24 609.6 30 609.6 NM-M(*)-(Matl)-24-30-HX* 723/4 1,848 74 1,880 963/4 2,457 1013/4 2,584
24 609.6 36 914.4 NM-M(*)-(Matl)-24-36-HX* 723/4 1,848 831/4 2,115 963/4 2,457 111 2,819
30 762 36 914.4 NM-M(*)-(Matl)-30-36-HX* 783/4 2,000 831/4 2,115 1023/4 2,610 111 2,819
(*) Side Rail Height. * NOTE: Insert radius, 12" (304.8mm) or 24" (609.6mm). Three pairs of fiberglass splice plates with SS6 hardware included.
Dimensions for reference only; when critical, contact your ABB representative. Consult your ABB representative for availability of molded fittings.
Standard rung spacing for fittings is 91/4" nominal (235mm). For other types of splice plates, see pages B38-B41.

Dimensions Sample mitered fitting

B

A W₂

W₁

—
Fitting number selection

NM - M 4 - P - 24 - 30 - HX 12

Nonmetallic Mitered Height Material Width 1 Width 2 Type Radius

 N O N M E TA L L I C - C A B L E T R AY F I T T I N G S B33

—
Nonmetallic - Cable tray fittings
3" (76.2mm), 4" (101.6mm), 6" (152.4mm) & 8" (203.2mm) - Horizontal expanding/
reducing cross fittings
—
Horizontal expanding/reducing cross – 36" (914.4mm) radius

Tray width (W1) Tray width (W2) 36" (914.4mm) Radius

(in.) (mm) (in.) (mm) Cat. No. A (in.) A (mm) B (in.) B (mm)
6 152.4 9 228.6 NM-M(*)-(Matl)-06-09-HX36 1023/4 2,610 1013/4 2,584
B
6 152.4 12 304.8 NM-M(*)-(Matl)-06-12-HX36 1023/4 2,610 111 2,819
6 152.4 18 457.2 NM-M(*)-(Matl)-06-18-HX36 1023/4 2,610 111 2,819
6 152.4 24 609.6 NM-M(*)-(Matl)-06-24-HX36 1023/4 2,610 1201/4 3,054
A W₂ 6 152.4 30 609.6 NM-M(*)-(Matl)-06-30-HX36 1023/4 2,610 1291/2 3,289

R 6 152.4 36 762 NM-M(*)-(Matl)-06-36-HX36 1023/4 2,610 1291/2 3,289

9 228.6 12 304.8 NM-M(*)-(Matl)-09-12-HX36 1053/4 2,686 111 2,819
W₁ 9 228.6 18 457.2 NM-M(*)-(Matl)-09-18-HX36 1053/4 2,686 111 2,819
9 228.6 24 609.6 NM-M(*)-(Matl)-09-24-HX36 1053/4 2,686 1201/4 3,054
9 228.6 30 609.6 NM-M(*)-(Matl)-09-30-HX36 1053/4 2,686 1291/2 3,289
9 228.6 36 762 NM-M(*)-(Matl)-09-36-HX36 1053/4 2,686 1291/2 3,289
12 304.8 18 457.2 NM-M(*)-(Matl)-12-18-HX36 1083/4 2,762 111 2,819
12 304.8 24 609.6 NM-M(*)-(Matl)-12-24-HX36 1083/4 2,762 1201/4 3,054
12 304.8 30 609.6 NM-M(*)-(Matl)-12-30-HX36 1083/4 2,762 1291/2 3,289
12 304.8 36 762 NM-M(*)-(Matl)-12-36-HX36 1083/4 2,762 1291/2 3,289
18 457.2 24 609.6 NM-M(*)-(Matl)-18-24-HX36 1153/4 2,940 1201/4 3,054
18 457.2 30 609.6 NM-M(*)-(Matl)-18-30-HX36 1153/4 2,940 1291/2 3,289
18 457.2 36 762 NM-M(*)-(Matl)-18-36-HX36 1153/4 2,940 1291/2 3,289
24 609.6 30 609.6 NM-M(*)-(Matl)-24-30-HX36 1203/4 3,067 1291/2 3,289
24 609.6 36 762 NM-M(*)-(Matl)-24-36-HX36 1203/4 3,067 1291/2 3,289
30 762 36 762 NM-M(*)-(Matl)-30-36-HX36 1263/4 3,219 1291/2 3,289
(*) Side Rail Height. Three pairs of fiberglass splice plates with SS6 hardware included. Dimensions for reference only; when critical, contact your ABB representative.
Consult your ABB representative for availability of molded fittings. Standard rung spacing for fittings is 91/4" nominal (235mm). For other types of splice plates, see pages B38-B41.

Sample mitered fitting

—
Fitting number selection

NM - M 4 - P - 24 - 30 - HX 36

Nonmetallic Mitered Height Material Width 1 Width 2 Type Radius

B34 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray fittings
3" (76.2mm), 4" (101.6mm), 6" (152.4mm) & 8" (203.2mm) - 90o Vertical inside/
outside bend fittings
—
90o Vertical inside bend fittings

Vertical bend 90°

Bend radius (R) Tray Height Vertical inside bend
(in.) (mm) (in.) (mm) Cat. No. A (in.) A (mm) L (in.) L (mm)
12 304.8 NM-M3-(Matl)-(*)-90VI12 18 5/16 465 25 15/16 659
24 609.6 3 76.2 NM-M3-(Matl)-(*)-90VI24 30 5/16 770 42 7/8 1089
W 36 914.4 NM-M3-(Matl)-(*)-90VI36 42 5/16 1075 59 7/8 1521
A
12 304.8 NM-M4-(Matl)-(*)-90VI12 20 7/8 530 29 1/2 749
24 609.6 4 101.6 NM-M4-(Matl)-(*)-90VI24 32 7/8 835 46 1/2 1181
36 914.4 NM-M4-(Matl)-(*)-90VI36 44 5/8 1133 63 5/16 1608
R 12 304.8 NM-M6-(Matl)-(*)-90VI12 20 7/8 530 29 1/2 749
24 609.6 6 152.4 NM-M6-(Matl)-(*)-90VI24 32 7/8 835 46 1/2 1181
L
36 914.4 NM-M6-(Matl)-(*)-90VI36 44 5/8 1133 63 5/16 1608
12 304.8 NM-M8-(Matl)-(*)-90VI12 20 7/8 530 29 1/2 749
24 609.6 8 203.2 NM-M8-(Matl)-(*)-90VI24 32 7/8 835 46 1/2 1181
36 914.4 NM-M8-(Matl)-(*)-90VI36 44 5/8 1133 63 5/16 1608
(*) Cable tray Width offered in 6'', 9'', 12'', 18'', 24'', 30'', 36''
One pair of fiberglass splice plates with SS6 hardware included.
Dimensions for reference only; when critical, contact your ABB representative. Consult your ABB representative for availability of molded fittings.
Standard rung spacing for fittings is 91/4" nominal (235mm). For other types of splice plates, see pages B38-B41.

—
90o Vertical outside bend fittings

Vertical bend 90°

Bend radius (R) Tray Height Vertical outside bend
(in.) (mm) (in.) (mm) Cat. No. A (in.) A (mm) L (in.) L (mm)
12 304.8 NM-M3-(Matl)-(*)-90VO12 18 15/16 481 26 3/4 679
24 609.6 3 76.2 NM-M3-(Matl)-(*)-90VO24 30 15/16 786 43 3/4 1111
36 914.4 NM-M3-(Matl)-(*)-90VO36 42 15/16 1091 60 11/16 1541
W 12 304.8 NM-M4-(Matl)-(*)-90VO12 19 7/8 505 28 1/8 714
L 24 609.6 4 101.6 NM-M4-(Matl)-(*)-90VO24 31 7/8 810 45 1/16 1145
36 914.4 NM-M4-(Matl)-(*)-90VO36 43 7/8 1114 62 1/16 1576
12 304.8 NM-M6-(Matl)-(*)-90VO12 21 7/8 556 30 15/16 786
A
R 24 609.6 6 152.4 NM-M6-(Matl)-(*)-90VO24 33 7/8 860 47 15/16 1218
36 914.4 NM-M6-(Matl)-(*)-90VO36 45 7/8 1165 64 7/8 1648
12 304.8 NM-M8-(Matl)-(*)-90VO12 23 7/8 606 33 3/4 857
24 609.6 8 203.2 NM-M8-(Matl)-(*)-90VO24 35 7/8 911 50 3/4 1289
36 914.4 NM-M8-(Matl)-(*)-90VO36 47 7/8 1216 67 3/4 1721
(*) Cable tray Width offered in 6'', 9'', 12'', 18'', 24'', 30'', 36''
One pair of fiberglass splice plates with SS6 hardware included.
Dimensions for reference only; when critical, contact your ABB representative. Consult your ABB representative for availability of molded fittings.
Standard rung spacing for fittings is 91/4" nominal (235mm). For other types of splice plates, see pages B38-B41.

—
Fitting number selection

NM - M 4 - P - 24 - 90 VI 12

Nonmetallic Mitered Height Material Width Angle Type Radius

 N O N M E TA L L I C - C A B L E T R AY F I T T I N G S B35

—
Nonmetallic - Cable tray fittings
3" (76.2mm), 4" (101.6mm), 6" (152.4mm) & 8" (203.2mm) - 45o/30o Vertical inside bend fittings

—
45o Vertical inside bend

Vertical bend 45°

Bend radius (R) Tray Height Vertical inside bend
(in.) (mm) (in.) (mm) Cat. No. A (in.) A (mm) L (in.) L (mm)
12 304.8 NM-M3-(Matl)-(*)-45VI12 9 5/8 244 18 1/16 459
R 24 609.6 3 76.2 NM-M3-(Matl)-(*)-45VI24 13 1/8 333 29 9/16 751
36 914.4 NM-M3-(Matl)-(*)-45VI36 16 5/8 422 35 1/16 891
12 304.8 NM-M4-(Matl)-(*)-45VI12 11 1/16 281 19 7/8 505
A
24 609.6 4 101.6 NM-M4-(Matl)-(*)-45VI24 14 5/8 371 28 3/8 721
W 36 914.4 NM-M4-(Matl)-(*)-45VI36 18 1/8 460 36 7/8 937
L 12 304.8 NM-M6-(Matl)-(*)-45VI12 12 1/2 318 19 7/8 505
24 609.6 6 152.4 NM-M6-(Matl)-(*)-45VI24 16 406 28 3/8 721
36 914.4 NM-M6-(Matl)-(*)-45VI36 19 1/2 495 36 7/8 937
12 304.8 NM-M8-(Matl)-(*)-45VI12 13 7/8 352 19 7/8 505
24 609.6 8 203.2 NM-M8-(Matl)-(*)-45VI24 17 7/16 443 28 3/8 721
36 914.4 NM-M8-(Matl)-(*)-45VI36 20 15/16 532 36 7/8 937
(*) Cable tray Width offered in 6'', 9'', 12'', 18'', 24'', 30'', 36''
One pair of fiberglass splice plates with SS6 hardware included.
Dimensions for reference only; when critical, contact your ABB representative. Consult your ABB representative for availability of molded fittings.
Standard rung spacing for fittings is 91/4" nominal (235mm). For other types of splice plates, see pages B38-B41.

—
30o Vertical inside bend

Vertical bend 30°

Bend radius (R) Tray Height Vertical inside bend
(in.) (mm) (in.) (mm) Cat. No. A (in.) A (mm) L (in.) L (mm)
12 304.8 NM-M3-(Matl)-(*)-30VI12 8 203 18 457
24 609.6 3 76.2 NM-M3-(Matl)-(*)-30VI24 9 229 24 610
36 914.4 NM-M3-(Matl)-(*)-30VI36 11 279 30 762
A 12 304.8 NM-M4-(Matl)-(*)-30VI12 9 229 18 457
W 24 609.6 4 101.6 NM-M4-(Matl)-(*)-30VI24 10 254 24 610
36 914.4 NM-M4-(Matl)-(*)-30VI36 12 305 30 762
L 12 304.8 NM-M6-(Matl)-(*)-30VI12 10 254 18 457
24 609.6 6 152.4 NM-M6-(Matl)-(*)-30VI24 12 305 24 610
36 914.4 NM-M6-(Matl)-(*)-30VI36 14 356 30 762
12 304.8 NM-M8-(Matl)-(*)-30VI12 12 305 18 457
24 609.6 8 203.2 NM-M8-(Matl)-(*)-30VI24 14 356 24 610
36 914.4 NM-M8-(Matl)-(*)-30VI36 15 381 30 762
(*) Cable tray Width offered in 6'', 9'', 12'', 18'', 24'', 30'', 36''
One pair of fiberglass splice plates with SS6 hardware included.
Dimensions for reference only; when critical, contact your ABB representative. Consult your ABB representative for availability of molded fittings.
Standard rung spacing for fittings is 91/4" nominal (235mm). For other types of splice plates, see pages B38-B41.

—
Fitting number selection

NM - M 4 - P - 24 - 45 VI 12

Nonmetallic Mitered Height Material Width Angle Type Radius

B36 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray fittings
3" (76.2mm), 4" (101.6mm), 6" (152.4mm) & 8" (203.2mm) - 35o/45o Vertical outside bend fittings

—
45o Vertical outside bend

Vertical bend 45°

Bend radius (R) Tray Height Vertical outside bend
(in.) (mm) (in.) (mm) Cat. No. A (in.) A (mm) L (in.) L (mm)
12 304.8 NM-M3-(Matl)-(*)-45VO12 9 3/4 248 18 1/2 470
24 609.6 3 76.2 NM-M3-(Matl)-(*)-45VO24 13 5/16 338 27 686
L
36 914.4 NM-M3-(Matl)-(*)-45VO36 16 13/16 427 35 1/2 902
12 304.8 NM-M4-(Matl)-(*)-45VO12 10 3/4 273 19 3/16 487
A 24 609.6 4 101.6 NM-M4-(Matl)-(*)-45VO24 14 5/16 364 27 11/16 703
R 36 914.4 NM-M4-(Matl)-(*)-45VO36 17 13/16 452 36 1/8 918
12 304.8 NM-M6-(Matl)-(*)-45VO12 12 3/4 324 20 9/16 522
W
24 609.6 6 152.4 NM-M6-(Matl)-(*)-45VO24 16 5/16 414 29 1/16 738
36 914.4 NM-M6-(Matl)-(*)-45VO36 19 13/16 503 37 9/16 954
12 304.8 NM-M8-(Matl)-(*)-45VO12 14 3/4 375 22 559
24 609.6 8 203.2 NM-M8-(Matl)-(*)-45VO24 18 5/16 465 30 1/2 775
36 914.4 NM-M8-(Matl)-(*)-45VO36 21 13/16 554 39 991
(*) Cable tray Width offered in 6'', 9'', 12'', 18'', 24'', 30'', 36''
One pair of fiberglass splice plates with SS6 hardware included.
Dimensions for reference only; when critical, contact your ABB representative. Consult your ABB representative for availability of molded fittings.
Standard rung spacing for fittings is 91/4" nominal (235mm). For other types of splice plates, see pages B38-B41.

—
30o Vertical outside bend

Vertical bend 30°

Bend radius (R) Tray Height Vertical outside bend
(in.) (mm) (in.) (mm) Cat. No. A (in.) A (mm) L (in.) L (mm)
12 304.8 NM-M3-(Matl)-(*)-30VO12 7 178 17 432
L
24 609.6 3 76.2 NM-M3-(Matl)-(*)-30VO24 9 229 23 584
36 914.4 NM-M3-(Matl)-(*)-30VO36 11 279 29 737
12 304.8 NM-M4-(Matl)-(*)-30VO12 8 203 17 432
24 609.6 4 101.6 NM-M4-(Matl)-(*)-30VO24 10 254 23 584
36 914.4 NM-M4-(Matl)-(*)-30VO36 12 305 29 737
A
W 12 304.8 NM-M6-(Matl)-(*)-30VO12 10 254 18 457
24 609.6 6 152.4 NM-M6-(Matl)-(*)-30VO24 12 305 24 610
36 914.4 NM-M6-(Matl)-(*)-30VO36 14 356 30 762
12 304.8 NM-M8-(Matl)-(*)-30VO12 10 254 18 457
24 609.6 8 203.2 NM-M8-(Matl)-(*)-30VO24 12 305 24 610
36 914.4 NM-M8-(Matl)-(*)-30VO36 14 356 30 762
(*) Cable tray Width offered in 6'', 9'', 12'', 18'', 24'', 30'', 36''
One pair of fiberglass splice plates with SS6 hardware included.
Dimensions for reference only; when critical, contact your ABB representative. Consult your ABB representative for availability of molded fittings.
Standard rung spacing for fittings is 91/4" nominal (235mm). For other types of splice plates, see pages B38-B41.

—
Fitting number selection

NM - M 4 - P - 24 - 45 VO 12

Nonmetallic Mitered Height Material Width Angle Type Radius

 B37

—
Nonmetallic - Cable tray fittings
3" (76.2mm), 4" (101.6mm), 6" (152.4mm) & 8" (203.2mm) - Vertical tee fittings

—
Vertical tee

Bend
radius (R) Tray Height Vertical tee Up Vertical tee Down

(in.) (mm) (in.) (mm) A (in.) A (mm) B(in) B(mm) A (in.) A (mm) B(in) B(mm)
12 304.8 3 76.2 NM-M3-(Matl)-(*)-(**)12 26 15/16 684 50 7/8 1292 23 15/16 608 50 7/8 1292
VTU vertical tee up 12 304.8 NM-M4-(Matl)-(*)-(**)12 23 1/4 591 42 1/2 1080 19 1/4 489 42 1/2 1080
W
24 609.6 4 101.6 NM-M4-(Matl)-(*)-(**)24 35 1/4 895 66 1/2 1689 31 1/4 794 66 1/2 1689

A R 36 914.4 NM-M4-(Matl)-(*)-(**)36 41 3/4 1060 79 1/2 2019 37 3/4 959 79 1/2 2019
12 304.8 NM-M6-(Matl)-(*)-(**)12 32 813 58 1473 26 660 58 1473
W
24 609.6 6 152.4 NM-M6-(Matl)-(*)-(**)24 37 1/4 946 68 1/2 1740 31 1/4 794 68 1/2 1740
B 36 914.4 NM-M6-(Matl)-(*)-(**)36 43 1/2 1105 92 1/2 2350
49 1/2 1257 92 1/2 2350
12 304.8 NM-M8-(Matl)-(*)-(**)12 27 7/8 708 43 3/4 1111 19 1/2 495 43 3/4 1111
24 609.6 8 203.2 NM-M8-(Matl)-(*)-(**)24 33 7/8 860 61 3/4 1568 25 1/2 648 61 3/4 1568
VTD vertical tee down
36 914.4 NM-M8-(Matl)-(*)-(**)36 45 7/8 1165 85 3/4 2178 37 1/2 953 85 3/4 2178
B

R A

(*) Cable tray Width offered in 6'', 9'', 12'', 18'', 24'', 30'', 36''
(**) Add: "VTD" for vertical tee down or "VTU" for vertical tee up to complete Cat. No. Two pairs of fiberglass splice plates with SS6 hardware included.
Standard rung spacing for fittings is 91/4" nominal (235mm). For other types of splice plates, see pages 353-355

—
Fitting number selection

NM - M 4 - P - 24 - VTD 12

Nonmetallic Mitered Height Material Width Type Radius

B38 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray
Splice plates
— —
01 6" (152.4mm)
Splice plate (comes with
nonmetallic hardware)
Splice plate number selection
Example:
NM-XSS4004SS6
• 316 stainless steel
• 4 holes supplied with 316 stainless steel hardware
for a 4" (101.6mm) deep straight section.

NOTE: Splice plates shown on pages B38-B41

represent splices for 6" (152.4mm) side rail
height. Number of holes may vary with other side
rail heights.

—
01

NM - X SS 4 00 4 ( ) SS6

Cable tray No. of holes¹ Type / Angle Tray Series Hardware

system in plate Straight 4 step down 00 3" (76.2mm) 3 316 Stainless steel SS6
Nonmetallic 4 Slotted straight 01 4" (101.6mm) 4 Fiberglass FR³
NM Tray to box (90o horz.) 05 6" (152.4mm) 6
Vertical adjustable 02 8" (203.2mm) 8
30o Angle 30
Accessory Material Horizontal adjustable 03
number X Stainless steel SS 45o Angle 45 Type²
Polyester resin FP 90o Angle 90 Vertical V
Vinylester resin FV 22.5o Angle 22 Horizontal H

1 : 4 holes for series 3 and 4 only. 8 holes for series 6 and 8 only.
2 : Only noted for angled splice plates, do not include for straight, expansion and adjustable splice plates.
3 : Minimum order quantity of 7 is required.
 N O N M E TA L L I C - C A B L E T R AY S P L I C E P L AT E S B39

—
Nonmetallic - Cable tray
Splice plates

—
Standard splice plates

Cat. No. Material Height (in.) Height (mm)

(32mm)
NM-XSS-8008* Stainless steel 8 203.2
NM-XSS-4006* Polyester resin 6 152.4
Vinylester resin
(54
mm) NM-XSS-4004* 4 101.6
(225mm) (108
mm)
(162mm) NM-XSS-4003* 3 76.2

7/16”(11mm)

* Hardware suffix needed to complete catalog number. All splice plate hardware is 3⁄8". Quantity required supplied with each tray section. Order only pairs of splice plates needed for
field modifications. SS6 hardware supplied as standard - use SS6 suffix. Other hardware available; specify by hardware suffix.

—
Expansion splice plates

Cat. No. Material Height (in.) Height (mm)

7/16" x 1"
(11mm x 25mm)
NM-XSS-8018* Stainless steel 8 203.2
slot
NM-XSS-8016* Polyester resin 6 152.4
Vinylester resin
NM-XSS-4014* 4 101.6
NM-XSS-4013* 3 76.2

Allow for up to 1" (25.4mm) expansion or contraction of tray system. For correct gap setting procedure, see page B10.
* Hardware suffix needed to complete catalog number.

—
Horizontal adjustable splice plates

Cat. No. Material Height (in.) Height (mm)

NM-XSS-8038* Stainless steel 8 203.2
6"
NM-XSS-4036* Polyester resin 6 152.4
(152mm)
Vinylester resin
NM-XSS-4034* 4 101.6
NM-XSS-4033* 3 76.2

Provide for changes in the horizontal direction that do not conform to standard fittings. Furnished in pairs.
* Hardware suffix needed to complete catalog number.

—
Vertical adjustable splice plates

Cat. No. Material Height (in.) Height (mm)

7/16" x 1"
51/16" 1" NM-XSS-8028* Stainless steel 8 203.2
(129mm) (25mm)
(11mm x 25mm)
slot, typ. NM-XSS-4026* Polyester resin 6 152.4
1"
(25mm)
Vinylester resin
NM-XSS-4024* 4 101.6
45/8"
25/8"
(117mm)
(67mm) NM-XSS-4023* 3 76.2

63/8" 21/8"
(162mm) (54mm)

Provide for changes in elevation that do not conform to standard vertical fittings. Furnished in pairs.
* Hardware suffix needed to complete catalog number.
 B40 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray
Splice plates

• Used to attach the end of a tray run to a

57/16"
(138mm)
distribution box or control center
11/4"
(32mm) • Furnished in pairs

57/16"
21/8" (138mm)
(54mm)

—
Tray-to-box splice plates

Cat. No. Cat. No. Cat. No.

Stainless steel Polyester resin Vinylester resin Height (in.) Height (mm)
NM-XSS8058* NM-XFP8058* NM-XFV8058* 8 203.2
NM-XSS4056* NM-XFP4056* NM-XFV4056* 6 152.4
NM-XSS4054* NM-XFP4054* NM-XFV4054* 4 101.6
NM-XSS4053* NM-XFP4053* NM-XFV4053* 3 76.2
Hardware other than SS6 is considered special. * Hardware supplied: 1 bolt and 1 springless strut nut 3/8 diameter.

• Easy-to-install design
• Compatible with all series of T&B Cable Tray
• Available in aluminum, pre-galvanized steel,
hot-dipped galvanized steel and
stainless steel 316
• Versatile use for strut and beam installations
Clamp position
on cable tray • Functional in all cable tray positions including
vertical installations

—
Combo hold down guide clamp

Cat. No. Material Hardware size (in.) Std. pkg. qty.

SSWCHGC Stainless steel type 316L 3/8 1
SSWCHGC-HDW* Stainless steel type 316L 3/8 1
* Hardware supplied: 1 bolt and 1 springless strut nut 3/8 diameter.

21/8" 21/8" 21/8" 21/8" 21/8" 21/8" 21/8" 11/4" 21/8" 21/8" 21/8" 21/8" 21/8" 21/8" 21/8" 11/4" 23/4"(69mm)
(54mm) (54mm) (54mm) (54mm) (54mm) (54mm) (54mm) (32mm) (54mm) (54mm) (54mm) (54mm) (54mm) (54mm) (54mm) (32mm)

B+-1/16"

A+-1/16" 25/8"(67mm)

7/16"(11mm) hole
171/4" (438mm) 171/4" (438mm)

—
Heavy duty splice plate

Cat. No. Polyester resin Description Height (in.) Height (mm)

NM-ESP-4C-180 4 101.6
NM-ESP-6C-180 Standard Splice Plate 6 152.4
NM-ESP-8C-180 8 203.2
NM-EEP-4C-180 4 101.6
NM-EEP-6C-180 Expansion Splice Plate 6 152.4
NM-EEP-8C-180 8 203.2
 N O N M E TA L L I C - C A B L E T R AY S P L I C E P L AT E S B41

—
Nonmetallic - Cable tray
Splice plates

45/8"
90o (117mm) 45o 7/16"
30o 22.5o
(11mm) 21/8"
hole (54mm)

30° 22.5°

107/8"
(276mm) 11/4"
(32mm)

47/8"
(124mm)

—
Vertical splice plate

Cat. No. Cat. No. Cat. No. Height Height Cat. No. Cat. No. Cat. No. Height Height
Stainless steel Polyester resin Vinylester resin (in.) (mm) Stainless steel Polyester resin Vinylester resin (in.) (mm)
90° 30°
NM-XSS-8908V* NM-XFP-8908V* NM-XFV-8908V* 8 203.2 NM-XSS-8308V* NM-XFP-8308V* NM-XFV-8308V* 8 203.2
NM-XSS-8906V* NM-XFP-8906V* NM-XFV-8906V* 6 152.4 NM-XSS-8306V* NM-XFP-8306V* NM-XFV-8306V* 6 152.4
NM-XSS-4904V* NM-XFP-4904V* NM-XFV-4904V* 4 101.6 NM-XSS-4304V* NM-XFP-4304V* NM-XFV-4304V* 4 101.6
NM-XSS-4903V* NM-XFP-4903V* NM-XFV-4903V* 3 76.2 NM-XSS-4303V* NM-XFP-4303V* NM-XFV-4303V* 3 76.2
45° 22.5°
NM-XSS-8458V* NM-XFP-8458V* NM-XFV-8458V* 8 203.2 NM-XSS-8228V* NM-XFP-8228V* NM-XFV-8228V* 6 152.4
NM-XSS-8456V* NM-XFP-8456V* NM-XFV-8456V* 6 152.4 NM-XSS-8226V* NM-XFP-8226V* NM-XFV-8226V* 6 152.4
NM-XSS-4454V* NM-XFP-4454V* NM-XFV-4454V* 4 101.6 NM-XSS-4224V* NM-XFP-4224V* NM-XFV-4224V* 4 101.6
NM-XSS-4453V* NM-XFP-4453V* NM-XFV-4453V* 3 76.2 NM-XSS-4223V* NM-XFP-4223V* NM-XFV-4223V* 3 76.2
* Hardware suffix needed to complete catalog number. * Hardware suffix needed to complete catalog number.

90o 45o 30o 22.5o

47/8"
11/4" (124mm)
(32mm)
57/16" 11/4"
(138mm) (32mm) 21/8"
(54mm)

21/8" 57/16"
(54mm) (138mm)

7/16"
(11mm)
hole

—
Horizontal splice plates

Cat. No. Cat. No. Cat. No. Height Height Cat. No. Cat. No. Cat. No. Height Height
Stainless steel Polyester resin Vinylester resin (in.) (mm) Stainless steel Polyester resin Vinylester resin (in.) (mm)
90° 30°
NM-XSS-8908H* NM-XFP-8908H* NM-XFV-8908H* 8 203.2 NM-XSS-8308H* NM-XFP-8308H* NM-XFV-8308H* 8 203.2
NM-XSS-8906H* NM-XFP-8906H* NM-XFV-8906H* 6 152.4 NM-XSS-8306H* NM-XFP-8306H* NM-XFV-8306H* 6 152.4
NM-XSS-4904H* NM-XFP-4904H* NM-XFV-4904H* 4 101.6 NM-XSS-4304H* NM-XFP-4304H* NM-XFV-4304H* 4 101.6
NM-XSS-4903H* NM-XFP-4903H* NM-XFV-4903H* 3 76.2 NM-XSS-4303H* NM-XFP-4303H* NM-XFV-4303H* 3 76.2
45° 22.5°
NM-XSS-8458H* NM-XFP-8458H* NM-XFV-8458H* 8 203.2 NM-XSS-8228H* NM-XFP-8228H* NM-XFV-8228H* 6 152.4
NM-XSS-8456H* NM-XFP-8456H* NM-XFV-8456H* 6 152.4 NM-XSS-8226H* NM-XFP-8226H* NM-XFV-8226H* 6 152.4
NM-XSS-4454H* NM-XFP-4454H* NM-XFV-4454H* 4 101.6 NM-XSS-4224H* NM-XFP-4224H* NM-XFV-4224H* 4 101.6
NM-XSS-4453H* NM-XFP-4453H* NM-XFV-4453H* 3 76.2 NM-XSS-4223H* NM-XFP-4223H* NM-XFV-4223H* 3 76.2
* Hardware suffix needed to complete catalog number. * Hardware suffix needed to complete catalog number.
B42 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray systems
Drop outs and barrier strips

Specially designed ladder drop outs provide a

rounded surface with adequate radius to
protect cable as it exits from the tray, preventing
damage to insulation.

—
Ladder drop out

Cat. No. Material

NM-XDOP1104-W* Pultruded fiberglass
* Supplied with a 4in. Radius
W = Tray width.
—
Barriers

Cat. No. Material Side rail height (in.) Side rail height (mm)
NM-BS08P-120 Polyester resin 8 203.2
NM-BS06P-120 Polyester resin 6 152.4
NM-BS04P-120 Polyester resin 4 101.6
NM-BS03P-120 Polyester resin 3 76.2
NM-BS08V-120 Vinylester resin 8 203.2
NM-BS06V-120 Vinylester resin 6 152.4
NM-BS04V-120 Vinylester resin 4 101.6
NM-BS03V-120 Vinylester resin 3 76.2
Barriers are provided in 10 ft. lengths and supplied for field installation using 3/16" SS rivets (ref. part # TPDR) or use of an adjustable clamp ref. part # XXX
(for 3, 4, 6 and 8" deep ladder tray).

Kit contents
• 1 pc. 72" (1,828.8mm) straight barrier
• 4 pc. XF-9002 barrier strip clip
• 8 pc. SS6 pop rivets
• 4 pc. #10 x 3⁄4" stainless steel self-tapping screw
• Assembly required - directions included
—
Flexible horizontal barrier kit

Cat. No. Material Side rail height (in.) Side rail height (mm) Loading depth (in.) Loading depth (mm)
NM-BS08P-90HBFL Polyester resin 8 203.2 611/16 169.86
NM-BS06P-90HBFL Polyester resin 6 152.4 411⁄16 119.06
NM-BS04P-90HBFL Polyester resin 4 101.6 211⁄16 68.26
NM-BS03P-90HBFL Polyester resin 3 76.2 13⁄4 44.45
NM-BS08V-90HBFL Vinylester resin 8 203.2 611/16 169.86
NM-BS06V-90HBFL Vinylester resin 6 152.4 411⁄16 169.86
NM-BS04V-90HBFL Vinylester resin 4 101.6 211⁄16 68.26
NM-BS03V-90HBFL Vinylester resin 3 76.2 13⁄4 44.45
One kit allows up to 38 (965.2mm) radius position of the barrier.
For larger than 38 (965.2mm) radius barrier position, two kits are required.
 N O N M E TA L L I C - C A B L E T R AY S Y S T E M S B43

—
Nonmetallic - Cable tray systems
Barrier strips and blind end plates

—
Barrier mounting angle clips with fasteners

Cat. No. Material

NM-PK-BAC Pultruded fiberglass
(polyester & vinylester)

VO
• Barriers for vertical fitting
• Please add angle (X) and radius (†) to
catalog number
• Furnished with #10 x 3⁄4" self-tapping stainless
steel screws

VI
—
Vertical barrier

Cat. No. Material Height (in.) Height (mm)

NM-BS08P(X)VI/VO Polyester resin 8 203.2
NM-BS06P(X)VI/VO Polyester resin 6 152.4
NM-BS04P(X)VI/VO Polyester resin 4 101.6
NM-BS03P(X)VI/VO Polyester resin 3 76.2
NM-BS08V(X)VI/VO Vinylester resin 8 203.2
NM-BS06V(X)VI/VO Vinylester resin 6 152.4
NM-BS04V(X)VI/VO Vinylester resin 4 101.6
NM-BS03V(X)VI/VO Vinylester resin 3 76.2
VI = inside vertical, VO = outside vertical.

—
Blind end plates

Cat. No. Material Height (in.) Height (mm)

NM-XBE*1088W** Polyester/ Vinylester 8 203.2
NM-XBE*1086W** Polyester/ Vinylester 6 152.4
NM-XBE*1084W** Polyester/ Vinylester 4 101.6
NM-XBE*1083W** Polyester/ Vinylester 3 76.2

Forms a closure for any tray that dead ends. Furnished as one plate.
* Material suffix, P=Polyester, V= Vinylester. ** Hardware suffix needed to complete catalog number.
W = Tray width
B4 4 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Cable tray covers
Covers

Covers for straight sections

• Material thickness: 1/8" (3.18mm)
• Standard cover length: 120" (10 ft.)
• 1/4" (6.35mm) diameter stainless fasteners with
flat washers included

Covers for fittings

• Material thickness: 1/8" (3.18mm)
• 1/4" (6.35mm) diameter stainless fasteners with
flat washers included

Covers for straight sections - Selection guide

NM - FC P 12 120

Cable tray system: Type of cover Material: Tray width: Length:

Nonmetallic Flat FC Polyester resin P 6 to 36 10 ft. (3.05m)
Peaked PC Vinylester resin V

Covers for fittings - Selection guide

NM - FC P 12 HB 90 24

Cable tray system: Type of cover Material: Tray width: Fitting Angle: Radius:
Nonmetallic Flat FC Polyester resin P 6 to 36 designation: 30 12
Vinylester resin V HB 45 24
VI/VO 60 36
HT 90
HX

—
NOTE: Peaked fitting
covers not available.
Other fitting covers are
available. Please consult
your ABB representative.
 N O N M E TA L L I C - C A B L E T R AY - A C C E S S O R I E S B45

—
Nonmetallic - Cable tray
Accessories

2" (51mm) • Recommended for outdoor service

1/4" bolt
3/16" (5mm) • Heavy-duty cover clamp available for flat
covers only
• Available in stainless steel only

—
Heavy-duty cover clamp

Cat. No. Material Side rail width (in.) Side rail width (mm)
NM-XWC-P-08-9034 Stainless steel 8 203.2
NM-XWC-P-W6-9034 6 152.4
NM-XWC-P-04-9034 4 101.6
NM-XWC-P-03-9034 3 76.2

—
Pop rivets

Cat. No. Material

TPDR Stainless steel
Thermoplastic

Raised cover clamps available.

Please consult your ABB representative.

Kit contents
• Resin
• Catalyst
• Stir stick and applicator

—
Brush-on resin seal kit

Cat. No. Description

NM-RSK-QT 946 ml
To reseal fiberglass after field modifications.
Vinylester resin.
B46 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Channel tray
Straight lengths
— —
NOTE: Splice plates NOT
included. See pages
B38-B41 for type of splice
Channel tray
plates available.
Covers are available. ABB offers nonmetallic cable channel in solid or
Please consult your ABB
representative.
ventilated straight sections. Horizontal and vertical
solid bottom fittings are also available to complete
your system layout.

—
Channel tray fitting selection
Example:
NM-FCCVP04-120 for polyester resin cable channel,
4" (101.6mm) wide ventilated bottom,
120" (10 ft. / 3.05m) length. NOTE: Straights are
provided without splice plate.
 N O N M E TA L L I C - C H A N N E L T R AY S T R A I G H T L E N G T H S B47

—
Specifications - Ventilated

Width Height Length Material

(in.) (mm) (in.) (mm) (ft.) (m) Polyester Vinylester
3 76.2 1 25.4 10 3.05 NM-FCCVP-03-120 NM-FCCVV-03-120
3 76.2 1 25.4 20 6.10 NM-FCCVP-03-240 NM-FCCVV-03-240
4 101.6 11/8 28.6 10 3.05 NM-FCCVP-04-120 NM-FCCVV-04-120
4 101.6 11/8 28.6 20 6.10 NM-FCCVP-04-240 NM-FCCVV-04-240
6 152.4 15/8 41.3 10 3.05 NM-FCCVP-06-120 NM-FCCVV-06-120
6 152.4 15/8 41.3 20 6.10 NM-FCCVP-06-240 NM-FCCVV-06-240
8 203.2 23/16 55.6 10 3.05 NM-FCCVP-08-120 NM-FCCVV-08-120
8 203.2 23/16 55.6 20 6.10 NM-FCCVP-08-240 NM-FCCVV-08-240

—
Specifications - Non-ventilated

Width Height Length Material

(in.) (mm) (in.) (mm) (ft.) (m) Polyester Vinylester
3 76.2 1 25.4 10 3.05 NM-FCCNP-03-120 NM-FCCNV-03-120
3 76.2 1 25.4 20 6.10 NM-FCCNP-03-240 NM-FCCNV-03-240
4 101.6 11/8 28.6 10 3.05 NM-FCCNP-04-120 NM-FCCNV-04-120
4 101.6 11/8 28.6 20 6.10 NM-FCCNP-04-240 NM-FCCNV-04-240
6 152.4 15/8 41.3 10 3.05 NM-FCCNP-06-120 NM-FCCNV-06-120
6 152.4 15/8 41.3 20 6.10 NM-FCCNP-06-240 NM-FCCNV-06-240
8 203.2 23/16 55.6 10 3.05 NM-FCCNP-08-120 NM-FCCNV-08-120
8 203.2 23/16 55.6 20 6.10 NM-FCCNP-08-240 NM-FCCNV-08-240

NM - FCC V - P - 04 - 120

Cable tray system Series Material Width Length

Nonmetallic NM Fiberglass cable channel FCC Polyester P 3" (76.2mm) 03 10ft. (3.05m) 120
Vinylester V 4" (101.6mm) 04 20ft. (6.10m) 240
6" (152.4mm) 06
8" (203.2mm) 08

Bottom type
Ventilated V
Non-ventilated N
B48 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Channel tray fittings
Horizontal bends and vertical bend fittings

22o-30'
• One pair of splice plates included
• For vinylester resin, use “V” instead of “P” in
45o catalog number
A
R • Example: FCCNV-04-90HB12

10"
22o-30'

W
—
Horizontal bends

Cat. No. Material Angle Side rail width (in.) Side rail width (mm)
NM-FCCNP-03-90HB12 Polyester / Vinylester resin 90o 3 76.2
NM-FCCNP-04-90HB12 Polyester / Vinylester resin 90o 4 101.6
NM-FCCNP-06-90HB12 Polyester / Vinylester resin 90o 6 152.4
NM-FCCNP-08-90HB12 Polyester / Vinylester resin 90o 8 203.2
NM-FCCNP-03-45HB12 Polyester / Vinylester resin 45o 4 76.2
NM-FCCNP-04-45HB12 Polyester / Vinylester resin 45o 4 101.6
NM-FCCNP-06-45HB12 Polyester / Vinylester resin 45o 6 152.4
NM-FCCNP-08-45HB12 Polyester / Vinylester resin 45o 8 203.2

VO VI W • One pair of splice plates included

22o-30' • For vinylester resin, use “V” instead of “P” in
catalog number
45o • Example: FCCNV-04-90VI12
R
R 22o-30' A
10"
A 10"
22o-30'

45o
22o-30'
W
—
Vertical bends

Cat. No. Material Angle Side rail width (in.) Side rail width (mm)
NM-FCCNP-03-90VI12* Polyester / Vinylester resin 90o 3 76.2
NM-FCCNP-04-90VI12* Polyester / Vinylester resin 90o 4 101.6
NM-FCCNP-06-90VI12* Polyester / Vinylester resin 90o 6 152.4
NM-FCCNP-08-90VI12* Polyester / Vinylester resin 90o 8 203.2
NM-FCCNP-03-45VI12* Polyester / Vinylester resin 45o 4 76.2
NM-FCCNP-04-45VI12* Polyester / Vinylester resin 45o 4 101.6
NM-FCCNP-06-45VI12* Polyester / Vinylester resin 45o 6 152.4
NM-FCCNP-08-45VI12* Polyester / Vinylester resin 45o 8 203.2
* For vertical outside bends, replace VI with VO
 N O N M E TA L L I C - C H A N N E L T R AY F I T T I N G S B49

—
Nonmetallic - Channel tray fittings
Horizontal tee and cross fittings

W
• Two pairs of splice plates included
• For vinylester resin, use “V” instead of “P” in
catalog number
18"
(457mm)
• Example: FCCNV-04-HT12

18" (457mm)
—
Horizontal tees

Cat. No. Material Side rail width (in.) Side rail width (mm)
NM-FCCNP-03-HT12 Polyester / Vinylester resin 3 76.2
NM-FCCNP-04-HT12 Polyester / Vinylester resin 4 101.6
NM-FCCNP-06-HT12 Polyester / Vinylester resin 6 152.4
NM-FCCNP-08-HT12 Polyester / Vinylester resin 8 203.2

W
• Three pairs of splice plates included
18" • For vinylester resin, use “V” instead of “P” in
(457mm) catalog number
• Example: FCCNV-04 -HX12
W

18" (457mm)

—
Horizontal crosses

Cat. No. Material Side rail height (in.) Side rail height (mm)
NM-FCCNP-03-HX12 Polyester / Vinylester resin 3 76.2
NM-FCCNP-04-HX12 Polyester / Vinylester resin 4 101.6
NM-FCCNP-06-HX12 Polyester / Vinylester resin 6 152.4
NM-FCCNP-08-HX12 Polyester / Vinylester resin 8 203.2
B50 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Channel tray systems
Standard and horizontal 90o, 45o, 30o & 22.5o splice plates

— —
Standard splice plates Horizontal 90o splice plates

Cat. No. Material Cat. No. Material

NM-XSS-1001-SS6 Stainless steel NM-XSS-1901H-SS6 Stainless steel
NM-XFP-1001-SS6 Polyester resin NM-XFP-1901H-SS6 Polyester resin
NM-XFV-1001-SS6 Vinylester resin NM-XFV-1901H-SS6 Vinylester resin
Supplied in pairs. Supplied with standard hardware, 1⁄4" stainless steel 316. Supplied in pairs. Supplied with standard hardware, 1⁄4" stainless steel 316.

— —
Horizontal 45o splice plates Horizontal 30o splice plates

Cat. No. Material Cat. No. Material

NM-XSS-1451H-SS6 Stainless steel NM-XSS-1301H-SS6 Stainless steel
NM-XFP-1451H-SS6 Polyester resin NM-XFP-1301H-SS6 Polyester resin
NM-XFV-1451H-SS6 Vinylester resin NM-XFV-1301H-SS6 Vinylester resin
Supplied in pairs. Supplied with standard hardware, 1⁄4" stainless steel 316. Supplied in pairs. Supplied with standard hardware, 1⁄4" stainless steel 316.

—
Horizontal 22.5o splice plates

Cat. No. Material

NM-XSS-1221H-SS6 Stainless steel
NM-XFP-1221H-SS6 Polyester resin
NM-XFV-1221H-SS6 Vinylester resin
Supplied in pairs. Supplied with standard hardware, 1⁄4" stainless steel 316.
 N O N M E TA L L I C - C H A N N E L T R AY S Y S T E M S B51

—
Nonmetallic - Channel tray systems
Expansion and vertical 90o, 45o, 30o & 22.5o splice plates

— —
Expansion splice plates Vertical 90o splice plates

Cat. No. Material Cat. No. Material

NM-XSS-1011-SS6 Stainless steel NM-XSS-1901V-SS6 Stainless steel
NM-XFP-1011-SS6 Polyester resin NM-XFP-1901V-SS6 Polyester resin
NM-XFV-1011-SS6 Vinylester resin NM-XFV-1901V-SS6 Vinylester resin
Supplied in pairs. Supplied with standard hardware, 1⁄4" stainless steel 316. Supplied in pairs. Supplied with standard hardware, 1⁄4" stainless steel 316.

— —
Vertical 45o splice plates Vertical 30o splice plates

Cat. No. Material Cat. No. Material

NM-XSS-1451V-SS6 Stainless steel NM-XSS-1301V-SS6 Stainless steel
NM-XFP-1451V-SS6 Polyester resin NM-XFP-1301V-SS6 Polyester resin
NM-XFV-1451V-SS6 Vinylester resin NM-XFV-1301V-SS6 Vinylester resin
Supplied in pairs. Supplied with standard hardware, 1⁄4" stainless steel 316. Supplied in pairs. Supplied with standard hardware, 1⁄4" stainless steel 316.

—
Vertical 22.5o splice plates

Cat. No. Material

NM-XSS-1221V-SS6 Stainless steel
NM-XFP-1221V-SS6 Polyester resin
NM-XFV-1221V-SS6 Vinylester resin
Supplied in pairs. Supplied with standard hardware, 1⁄4" stainless steel 316.
B52 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Strut systems
Channels
—
Channels
ABB is proud of its line of nonmetallic strut and ac-
cessories. You’ll find a complete
selection of nonmetallic accessories, fasteners,
hangers, pipe clamps and channels.

Most ABB strut products are available in a choice of

resins – either vinylester or
polyester. Our design and engineering staff is
ready to help you select the material that
best suits your needs.

—
Channel fitting selection
Example:
— NM-SSP-100-120, 1" (25.5mm) single strut, 120"
*NOTE: The U-style and
H-style systems are
(10 ft. / 3.05m) NOTE: Stocked in 120" (10 ft. /
interchangeable. 3.05m) and 240" (20 ft. / 6.10m) lengths.

NM - SS P - 120 - ( ) - ( ) - 120

Strut system Type of system Size Holes/insert Length

Nonmetallic NM Strut system SS 1" (25.5mm) 100 Holes H 10ft. (3.05m) 12
15/8" (41.3mm) 158 Insert I 20ft. (6.10m) 24

Material Double
Polyester P Double D
Vinylester V Single Blank
 N O N M E TA L L I C - S T R U T S Y S T E M S B53

—
Nonmetallic - Strut systems
Channels - Combinations and hole pattern

—
Solid – Single strut

Weight
Cat. No. Material/resin Color (lb/ft.) (kg/m)
NM-SS(*)-100 NM-SS(*)-158 NM-SSP-100-(L) Polyester Gray 0.47 0.70
7/16" 3/4" 7/16" 3/4" NM-SSP-158-(L) Polyester Gray 0.63 0.94
(11mm) (19mm) (11mm) (19mm)
NM-SSV-100-(L) Vinylester Beige 0.47 0.70
9/32" 11/8" (28mm) 9/32"
(7mm) (7mm) 15/8" (41mm) NM-SSV-158-(L) Vinylester Beige 0.63 0.94
15/8"
(41mm) 15/8"
(41mm)

*Add P for polyester or V for vinylester.

(L) Add desired length 120 (10 ft.) or 240 (20 ft.)
Cut-to-length channel also available.

—
Solid – Back to back

Weight
Cat. No. Material/resin Color (lb/ft.) (kg/m)
NM-SS(*)-100-D NM-SS(*)-158-D NM-SSP-100-D-(L) Polyester Gray 0.86 1.28
7/16" 3/4" 7/16" 3/4" (19mm) NM-SSP-158-D-(L) Polyester Gray 1.17 1.75
(11mm) (19mm) (11mm)
NM-SSV-100-D-(L) Vinylester Beige 0.86 1.28
11/8" 9/32" 9/32"
(7mm) 15/8" (7mm) NM-SSV-158-D-(L) Vinylester Beige 1.17 1.75
21/4"
(56mm) 31/4"
(28mm)

(41mm) (82mm)

15/8"
(41mm)
15/8"
(41mm)

*Add P for polyester or V for vinylester.

(L) Add desired length 120 (10 ft.) or 240 (20 ft.)
Cut-to-length channel also available.

—
Punched

Weight
Cat. No. Material/resin Color (lb/ft.) (kg/m)

NM-SS(*)-100-H NM-SS(*)-158-H NM-SSP-100-H-(L) Polyester Gray 0.47 0.67

7/16" 3/4" 7/16" 3/4" (19mm) NM-SSP-158-H-(L) Polyester Gray 0.63 0.91
(11mm) (19mm) (11mm)
NM-SSV-100-H-(L) Vinylester Beige 0.45 0.67
9/32" 11/8" (28mm) 9/32"
(7mm) (7mm) 15/8" (41mm) NM-SSV-158-H-(L) Vinylester Beige 0.61 0.91

15/8"
(41mm) 15/8"
(41mm)
2"
(51mm)
1"
(25mm)

9/16"
(14mm)

*Add P for polyester or V for vinylester.

(L) Add desired length 120 (10 ft.) or 240 (20 ft.)
Cut-to-length channel also available.
B54 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Strut systems
Superstrut™ fittings and brackets

— — — —
01 02 03 04
41mm
mm
41mm
mm 41mm
mm 140mm
0mm
15/8"
15/8 82mm
mm
15/8"
15/8 15/8"
15/8 51/2"
51/2
31/4"
31/4

11mm
mm 14mm
mm
7/16"
7/16 9/16" hole
9/16

— — — —
05 06 07 08
117mm
mm 89mm
mm
45/8"
45/8 31/2"
31/2
203mm
mm 117mmmm
254mm
mm 45/8"
45/8
8"
10"
10

136mm
mm
53/8"
53/8

— — — —
09 10 11 12
117mm
mm 178mm
mm 89mm
mm 117mm
mm
45/8"
45/8 7" 31/2"
31/2
89mm
mm 45/8"
45/8
31/2"
31/2

152mm
mm
6" 178mm
mm 152mm
mm
7" 6"

— —
13 14
89mm
mm
137mm
mm 31/2"
31/2
— 53/8"
53/8
01 NM-SFP-1S7
—
02 NM-SFP-1S9 137mmmm
—
03 NM-SFP-2S 53/8"
53/8 89mm
mm
— 31/2"
31/2
04 NM-SFP-3S
—
05 NM-SFP-4S
—
06 NM-SFP-5S
—
07 NM-SFP-3HL
—
08 NM-SFP-4HL — —
— 15 16
09 NM-SFP-4HT 89mm
mm
— 31/2"
31/2
10 NM-SFP-5HX 178mm
mm
— 7"
11 NM-SFP-3HCG
—
12 NM-SFP-4HCG
— —
13 NM-SFP-5HCG NOTE: Based on individual applications, changes 136mm
mm
— may be required on dimension and thickness 53/8"
53/8 7"
14 NM-SFP-3HTG of material. All fittings are 1⁄4" (6mm) thick unless
— mm
178mm
specified otherwise. All holes are drilled to
15 NM-SFP-4HTG
— accept 3/8" and 1/2" bolts with washers. Not supplied
16 NM-SFP-5HTG with hardware.
 N O N M E TA L L I C - S T R U T S Y S T E M S B55

—
Nonmetallic - Strut systems
Superstrut fittings and brackets

— — — —
01* 02* 03* 04*
253mm
mm 41mm
mm
10"
10 254mm
mm 15/8"
15/8 101mm
mm
10"
10 4"
117mm
mm
45/8"
45/8 127mm
mm
5" 101mm
mm
4"
178mm
mm
7"
7

— — — —
41mm
mm 05* 06* 07* 08*
114mm
mm 41mm
mm
15/8"
15/8 102mm
mm 102mm
mm
41/2"
41/2 15/8"
15/8
4" 4"

56mm
mm 102mm
mm
21/4"
21/4 4"
114mm
mm 114mmmm
41/2"
41/2 41/2"
41/2
82mm
mm
41mm
mm
15/8"
15/8

— — — —
09 10 All holes 7/16" 11 All holes 7/16" 12
38mm
mm or 11mm or 11mm
11/2"
11/2
27mm
mm 76mm
mm 76mm
mm
11/16"
11/16 3" 3"
69mm
mm
133mm
mm
23/4" 4
23/4 4"
51/4"
51/4
mm
101mm 127mm
mm 127mm
mm
13/4
13/4" 6.5"
6.5 5"
44mm
mm 5" 5"
66mm
mm 165mm
mm mm
127mm
89mmmm
25/8"
25/8 31/2"
31/2

—
01 NM-SFP-6HTG
—
02 NM-SFP-7HXG
—
03 NM-SFP-3VL
—
04 NM-SFP-4VL
—
05 NM-SFP-4VLD
—
06 NM-SFP-4VGL
—
07 NM-SFP-4VGR
—
08 NM-SFP-4VTG
— —
09 NM-SFP-3CB * Items 2 thru 8 (FRP angle components) will not
— support tensile loads or forces.
10 NM-SWC-158 —
— NOTE: Based on individual applications, changes
11 NM-SSV-DBASE may be required on dimension and thickness
— of material. All fittings are 1⁄4" (6mm) thick unless
12 NM-SSV-SBASE specified otherwise. All holes are drilled to
accept 3/8" and 1/2" bolts with washers. Not supplied
with hardware.
B56 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Strut systems
Nonmetallic threaded hardware

—
Hex head bolt

Bolt
Thread length Design load Max. torque Weight / C
Cat. No. size (in.) (lb) N in - lb N-m (lb) (g)
NM-F516100 5/16" - 18 5/16 x 1 190 845 30 3.4 0.4 181
NM-F516114 5/16" - 18 5/16 x 11/4 190 845 30 3.4 0.4 181
NM-F38100 3/8" - 16 3/8 x 1 300 1,334 45 5.1 0.9 408
NM-F38114 3/8" - 16 3/8 x 11/4 300 1,334 45 5.1 1.1 499
NM-F38212 3/8" - 16 3/8 x 21/2 300 1,334 45 5.1 1.5 680
NM-F12100 1/2" - 13 1/2 x 1 490 2,180 110 12.4 1.4 635
NM-F12114 1/2" - 13 1/2 x 11/4 490 2,180 110 12.4 1.8 816
NM-F12212 1/2" - 13 1/2 x 21/2 490 2,180 110 12.4 3.7 1,678
Safety factor of 3 on design load.

—
Hex nut

Height Weight / C
Cat. No. Thread size (in.) (mm) (lb) (g)
NM-F38HN 3/8" - 16 21/64 8 0.69 136
NM-F12HN 1/2" - 13 7/16 11 0.69 318
NM-F58HN 5/8" - 11 35/64 14 0.69 635

NOTE: 3⁄4" and 1" sizes are available.

Standard lengths are 4 ft. and 8 ft. Example: NM-F38HN-4.

—
All-thread rod

Design load Max. torque Weight / C

Thread
Cat. No. size (lb) N in - lb N-m (lb) (g)
NM-F38AT 3/8" - 16 425 1,890 45 5.1 0.08 36
Weight
NM-F12AT 1/2" - 13 750 3,336 110 12.4 0.13 59
NM-F58AT 5/8" - 11 950 4,226 230 26 0.21 95

Safety factor of 3 on design load. NOTE: 3⁄4" and 1" sizes are available.
 N O N M E TA L L I C - S T R U T S Y S T E M S B57

—
Nonmetallic - Strut systems
Nonmetallic threaded hardware

—
All-thread rod hex nut

Height Weight / C
Cat. No. Thread size (in.) (mm) (lb) (g)
NM-F38ATHN 3/8" - 16 3/4 19 0.8 376
NM-F12ATHN 1/2" - 13 7/8 22 1.7 771

—
Rod coupler

Weight / C
Cat. No. Thread size (lb) (kg)
NM-FRC38 3/8" - 16 7.4 3.36
NM-FRC12 1/2" - 13 11.3 5.13
NM-FRC58 5/8" - 11 16.7 7.57

3⁄4" and 1" sizes are available.

B58 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Strut systems
Nonmetallic pipe hangers, brackets and beam clamps

—
Clevis hangers

Nominal pipe size Max. O.D. range Hanger Design load

Cat. No. (in.) (mm) (in.) (mm) rod size (lb) N
NM-SCH200 2 50.8 21/2 63.5 1/2 - 13 90 0.40
NM-SCH212 21/2 63.5 31/4 82.6 1/2 - 13 120 0.54
NM-SCH300 3 76.2 37/8 98.4 1/2 - 13 160 0.71
NM-SCH400 4 101.6 5 127 5/8 - 11 250 1.12
NM-SCH600 6 152.4 7 177.8 5/8 - 11 400 1.79
NM-SCH800 8 203.2 9 228.6 5/8 - 11 450 2.01
NM-SCH1000 10 250 113/8 288.9 5/8 - 11 500 2.24
NM-SCH1200 12 304.8 131/2 342.9 5/8 - 11 600 2.69

Safety factor of 3 on design loads at 120°F (49°C). Insulation may be required at high temperatures.
Order hanger rods and nuts separately.

—
Support brackets

Dimension “A” Dimension “B” Dimension “C” Design load

Cat. No.* (in.) (mm) (in.) (mm) (in.) (mm) (lb) N
SB 1 NM-SB1-6P 10 254 12 304.8 10 254 1,600 7,117
NM-SB1-9P 13 330.2 12 304.8 10 254 1,100 4,893
NM-SB1-12P 16 406.4 12 304.8 10 254 850 3,781
NM-SB1-18P 22 558.8 12 304.8 10 254 725 3,225
NM-SB1-24P 28 711.2 12 304.8 10 254 480 2,135
NM-SB2-24P 26 660.4 21 533.4 15 381 750 3,336
SB 2 NM-SB2-30P 32 812.8 21 533.4 15 381 750 3,336
NM-SB2-36P 38 965.2 21 533.4 15 381 750 3,336

*Substitute “V” for “P” when vinylester resin is needed. Design loads based on uniform. Allowable load is based on a total load, uniformly distributed over the length of the rack.
Safety factor = 2.0 loading with a safety factor of 3.

—
Beam clamps

Design load
Cat. No. Description (lb/ft.) (kg/m)
1/2" - 13 x 2 NM-SBC Beam clamp 800 3.56
(Clamp
Screw only) Add “RC” for
retainer clip NM-SBC-RC Beam clamp with retainer clip 800 3.56
3" (76)
3"

11/4"
1 1⁄4 "
(108)
(108)
( 2 5))
11""(2 5

1 ⁄8 "
1
Tapped for
Tapped for 11/88")
1/2"
1
⁄2 "-–13
13rod
rod 2 8)
((2

Safety factor of 3 on design load.

 N O N M E TA L L I C - S T R U T S Y S T E M S B59

—
Nonmetallic - Strut systems
Nonmetallic pipe hangers and hardware

—
U-bolt

Nominal H
pipe size height Design load A Design load B Max. torque Weight / C
Cat. No. (in.) (mm) (in.) (lb) N (lb) N in - lb N-m (lb) (kg)
NM-FUB050 1/2 12.7 2.41 300 1,334 150 667 30 3.4 3.5 1.59
Load NM-FUB075 3/4 19.1 2.60 300 1,334 150 667 30 3.4 3.9 1.77
A
NM-FUB100 1 25.4 2.85 300 1,334 150 667 30 3.4 4.4 2.00
NM-FUB114 11/4 31.8 3.16 300 1,334 150 667 30 3.4 4.8 2.18
NM-FUB112 1 1/2 38.1 3.47 300 1,334 150 667 30 3.4 5.2 2.36
H NM-FUB200 2 50.8 4.18 600 2,669 200 890 60 6.8 7.7 3.49
NM-FUB212 21/2 63.5 4.68 600 2,669 200 890 60 6.8 10.2 4.63
NM-FUB300 3 76.2 5.31 600 2,669 200 890 60 6.8 12.6 5.72
NM-FUB312 31/2 88.9 5.81 600 2,669 200 890 60 6.8 15.1 6.85
NM-FUB400 4 101.6 6.31 600 2,669 200 890 60 6.8 17.6 7.98
Load
B
Pipe

Safety factor of 3 on design load.

—
Channel nut

Weight / C Dimension “t”

Part. No. Thread size (lb) (g) (in.) (mm)
NM-FCN14 1/4-20 5.58 2,531 11/16 27
NM-FCN38 3/8-16 5.31 2,408 11/16 27
NM- FCN12 1/2-13 5.27 2,390 11/16 27

Vinyl Ester resin is the standard. Channel nuts are self locking and designed for use with strut only. Resistance to slip = 450 Lbs. per bolt Pull out strength =
700 lb per bolt . Safety factor of 3 on design load.

—
Flat washer

Weight / C
Cat. No. Hole size (in.) (lb) (g)
NM-F38W 3/8 0.5 227
NM-F12W 1/2 0.5 227
NM-F58W 5/8 0.5 227
NM-F34W 3/4 0.5 227
NM-F100W 1 0.5 227
B60 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Strut systems
Sealant

Kit contents
• Resin
• Catalyst
• Stir stick and applicator

—
Brush-on resin seal kit

Cat. No. Description

NM-RSK-QT 946 ml
To reseal fiberglass after field modifications.
Vinylester resin.
 N O N M E TA L L I C - S T R U T S Y S T E M S B61

—
Nonmetallic - Strut systems
Pipe clamps

—
Rigid pipe clamp*

Nominal pipe size Design load Max. Torque

Cat. No. (in.) (mm) (lb) (kg) N (in. - lb) (N - m)
NM-SRPC050 1⁄2 12.7 300 136 1.33 10 1.13
NM-SRPC075 3⁄4 19.1 300 136 1.33 10 1.13
NM-SRPC100 1 25.4 300 136 1.33 10 1.13
NM-SRPC114 11⁄4 31.8 300 136 1.33 10 1.13
NM-SRPC112 11⁄2 38.1 300 136 1.33 10 1.13
NM-SRPC200 2 50.8 300 136 1.33 10 1.13
NM-SRPC212 21⁄2 63.5 300 136 1.33 10 1.13
NM-SRPC300 3 76.2 300 136 1.33 10 1.13
NM-SRPC312 31⁄2 88.9 300 136 1.33 10 1.13
NM-SRPC400 4 101.6 300 136 1.33 10 1.13
Safety factor of 3 on design load.
*Fastener is included

—
Conduit swivel clamp

Cat. No. Description

NM-SCSC-(CTD) Conduit swivel clamp

Rigid pipe
clamp (sold
separately)

Conduit

Cable tray
side rail

Cable tray designation (CTD) required. (Ex. 6CP series designates 6" deep polyester resin). Pipe clamps are a separate order item.
B62 T & B C A B L E T R AY N O N M E TA L L I C C A B L E T R AY S Y S T E M S

—
Nonmetallic - Strut systems
Channel Loading Chart

Loading information
Beam loads: The charts below list the total
allowable uniform load for various simple spans
based on a minimum safety factor of 2.
If the load is concentrated at center span, multiply
the load by 0.5 and the corresponding
deflection by 0.8.

—
Channel framing loading – Beam and column data: Polyester and vinyl ester resin base

Deflection @ Uniform load @ Uniform load @

Maximum allowable Maximum allowable Maximum deflection Maximum Deflection
uniform beam load uniform beam load = 0.25 in. (6mm) = 0.50 in. (13mm) Maximum
allowable
Beam span Poly Vinyl Poly Vinyl Poly Vinyl Poly Vinyl column load
in. / (mm) Cat. No. Ib (kg) Ib (kg) Ib (kg) (kg) Ib (kg) Ib (kg) Ib (kg) Ib (kg) Ib (kg)
12 (304.8) NM-SSP-100 790 (358) 990 (449) 0.11 (3) 0.12 (3) – – – – 2,550 (1,156)
NM-SSP-158 1,720 (780) 2,150 (975) 0.07 (2) 0.07 (2) – – – – 3,650 (1,655)
NM-SSP-158-D 5,080 (2,301) 6,350 (2,880) 0.04 (1) 0.04 (1) – – – – 7,300 (3,111)
18 (457) NM-SSP-100 530 (240) 670 (304) 0.24 (6) 0.27 (7) – 620 (281) – – 2,350 (1,066)
NM-SSP-158 1,150 (521) 1,440 (653) 0.15 (4) 0.17 (4) – - – – 3,370 (1,528)
NM-SSP-158-D 5,080 (2,301) 4,240 (1,923) 0.09 (2) 0.10 (2) – – – – 6,740 (3,058)
24 (609.6) NM-SSP-100 400 (181) 500 (227) 0.43 (11) 0.48 (12) 240 (109) 270 (122) – – 2,070 (939)
NM-SSP-158 860 (390) 1,080 (490) 0.27 (7) 0.30 (8) 810 (367) 910 (412) – – 2,960 (1,342)
NM-SSP-158-D 2,540 (1152) 3,180 (1,442) 0.16 (4) 0.17 (4) – – – – 5,920 (2,685)
30 (762) NM-SSP-100 320 (145) 400 (181) 0.67 (17) 0.75 (19) 120 (54) 140 (63) 240 (109) 270 (122) 1,710 (775)
NM-SSP-158 690 (313) 870 (394) 0.42 (11) 0.48 (12) 410 (186) 460 (209) – – 2,450 (1,111)
NM-SSP-158-D 2,040 (925) 2,550 (1,156) 0.24 (6) 0.27 (7) 2,000 (907) 2,350 (1,066) – – 4,900 (2,222)
36 (914.4) NM-SSP-100 270 (122) 340 (154) 0.98 (25) 1.10 (28) 70 (31) 80 (36) 140 (63) 160 (72) 1,260 (571)
NM-SSP-158 580 (263) 730 (331) 0.61 (15) 0.69 (19) 240 (109) 270 (122) 480 (217) 540 (245) 1,800 (816)
NM-SSP-158-D 1,700 (771) 2,130 (966) 0.35 (9) 0.39 (10) 1,220 (553) 1,370 (621) – – 3,600 (1,633)
42 (1066.8) NM-SSP-100 230 (104) 290 (131) 1.32 (34) 1.49 (38) 50 (22) 55 (25) 100 (45) 115 (52) 920 (417)
NM-SSP-158 490 (222) 620 (281) 0.82 (21) 0.92 (23) 150 (68) 170 (77) 300 (136) 340 (154) 1,320 (598)
NM-SSP-158-D 1,460 (662) 1,830 (830) 0.48 (12) 0.62 (16) 770 (349) 870 (394) 1,510 (650) 1,720 (530) 2,640 (1,197)
48 (1219.2) NM-SSP-100 200 (91) 250 (113) 1.72 (44) 1.92 (49) 30 (13) 25 (16) 60 (27) 70 (31) 700 (317)
NM-SSP-158 430 (195) 540 (245) 1.07 (27) 1.20 (30) 100 (45) 115 (52) 200 (90) 230 (104) 1,010 (458)
NM-SSP-158-D 1,270 (576) 1,590 (721) 0.62 (16) 0.69 (17) 520 (236) 590 (267) 1,040 (471) 1,170 (780) 2,020 (916)
60 (1524) NM-SSP-100 160 (72) 200 (91) 2.68 (68) 2.99 (76) 20 (9) 23 (10) 40 (18) 45 (20) 180 (81)
NM-SSP-158 350 (158) 400 (200) 1.70 (43) 1.91 (48) 60 (27) 70 (32) 120 (54) 135 (61) 260 (118)
NM-SSP-158-D 1,020 (462) 1,280 (580) 0.97 (25) 1.09 (28) 270 (122) 310 (140) 540 (245) 610 (276) 520 (235)
72 (1828.8) NM-SSP-100 140 (63) 180 (81) – – 10 (4) 12 (5) 20 (9) 23 (10) –
NM-SSP-158 290 (131) 370 (168) 2.44 (62) 2.78 (71) 30 (13) 34 (15) 60 (27) 70 (32) –
NM-SSP-158-D 850 (385) 1,070 (485) 1.40 (35) 1.57 (40) 160 (72) 180 (81) 320 (145) 360 (163) –
84 (2133.6) NM-SSP-100 120 (54) 150 (68) – – NR – 12 (5) 15 (7) –
NM-SSP-158 250 (113) 320 (145) – – 20 (9) 23 (10) 40 (18) 45 (20) –
NM-SSP-158-D 730 (331) 920 (417) 1.91 (48) 2.15 (55) 100 (45) 115 (52) 200 (90) 230 (104) –
96 (2438.4) NM-SSP-100 100 (45) 130 (59) – – NR – – – –
NM-SSP-158 220 (100) 250 (113) – – 13 (6) 15 (7) 26 (12) 30 (13) –
NM-SSP-158-D 640 (290) 800 (363) 2.50 (63) 2.79 (71) 70 (32) 80 (36) 140 (63) 160 (72) –
 N O N M E TA L L I C - S T R U T S Y S T E M S - C H A N N E L F R A M I N G LO A D I N G B63

Recommended guideline
Temperature Design load multiplier
Published design loads are based on usage at
75oF (24oC) 100%
70°F (21°C) and must be reduced for continuous
100oF (38oC) 90%
exposure to higher temperatures. Refer to the chart
125oF (52oC) 78%
opposite for high temperature applications.
150oF (66oC) 68%
175oF (79oC) 60%
200oF (93oC) 52%