Data sheet 6ES7135-6TD00-0CA1
SIMATIC ET 200SP, analog HART output module, AQ 4xI HART
High Feature, suitable for BU type A0, A1, Color code CC00, channel
diagnostics, 16 bit, +/-0.3%
General information
Product type designation AQ 4xI HART HF
Firmware version V1.0
● FW update possible Yes
usable BaseUnits BU type A0, A1
Color code for module-specific color identification CC00
plate
Product function
● I&M data Yes; I&M0 to I&M3
Engineering with
● STEP 7 TIA Portal configurable/integrated from V15 SP1
version
● STEP 7 configurable/integrated from version V5.6 and higher
● PCS 7 configurable/integrated from version V9.0 SP1
● PROFIBUS from GSD version/GSD revision V04.02.14
● PROFINET from GSD version/GSD revision GSDML V2.34
CiR - Configuration in RUN
6ES7135-6TD00-0CA1 Subject to change without notice
Page 1/4 12/10/2020 © Copyright Siemens
Reparameterization possible in RUN Yes
Calibration possible in RUN No
Supply voltage
Rated value (DC) 24 V
permissible range, lower limit (DC) 19.2 V
permissible range, upper limit (DC) 28.8 V
Reverse polarity protection Yes
Input current
Current consumption (rated value) 115 mA
Current consumption, max. 125 mA
Power loss
Power loss, typ. 1.7 W
Address area
Address space per module
● Address space per module, max. 8 byte; + 1 byte for QI information
● Address space per module with HART, max. 28 byte; + 1 byte for QI information
Analog outputs
Number of analog outputs 4
Current output, no-load voltage, max. 28 V
Cycle time (all channels), min. 3 ms
Output ranges, current
● 0 to 20 mA Yes; 16 bit incl. sign
● -20 mA to +20 mA No
● 4 mA to 20 mA Yes; 16 bit incl. sign
Connection of actuators
● for current output two-wire connection Yes
Load impedance (in rated range of output)
● with current outputs, max. 750 Ω
● with current outputs, inductive load, max. 10 mH
Destruction limits against externally applied voltages and currents
● Voltages at the outputs 30 V
Cable length
● shielded, max. 800 m
Analog value generation for the outputs
Settling time
● for resistive load 2 ms; 750 ohm
● for capacitive load 2 ms
● for inductive load 2 ms
Errors/accuracies
6ES7135-6TD00-0CA1 Subject to change without notice
Page 2/4 12/10/2020 © Copyright Siemens
Output ripple (relative to output range, bandwidth 0 to 0.02 %
50 kHz), (+/-)
Linearity error (relative to output range), (+/-) 0.03 %
Temperature error (relative to output range), (+/-) 0.003 %/K
Crosstalk between the outputs, min. -50 dB
Repeat accuracy in steady state at 25 °C (relative to 0.03 %
output range), (+/-)
Operational error limit in overall temperature range
● Current, relative to output range, (+/-) 0.3 %; 0 ... 60 °C: 0.2 %
Basic error limit (operational limit at 25 °C)
● Current, relative to output range, (+/-) 0.1 %
Protocols
HART protocol Yes
Interrupts/diagnostics/status information
Diagnostics function Yes
Substitute values connectable Yes
Alarms
● Diagnostic alarm Yes
Diagnoses
● Monitoring the supply voltage Yes; Module-wise
● Wire-break Yes; channel by channel
● Short-circuit Yes
● Overflow/underflow Yes; channel by channel
Diagnostics indication LED
● Monitoring of the supply voltage (PWR-LED) Yes; green PWR LED
● Channel status display Yes; green LED
● for channel diagnostics Yes; red LED
● for module diagnostics Yes; green/red DIAG LED
Potential separation
Potential separation channels
● between the channels No
● between the channels and backplane bus Yes
● Between the channels and load voltage L+ Yes
Permissible potential difference
between different circuits 60 V DC/30 V AC
Isolation
Isolation tested with 707 V DC (type test)
Ambient conditions
Ambient temperature during operation
● horizontal installation, min. -30 °C
6ES7135-6TD00-0CA1 Subject to change without notice
Page 3/4 12/10/2020 © Copyright Siemens
● horizontal installation, max. 60 °C
● vertical installation, min. -30 °C
● vertical installation, max. 50 °C
Altitude during operation relating to sea level
● Installation altitude above sea level, max. 5 000 m; restrictions for installation altitudes > 2 000 m, see ET
200SP system manual
Dimensions
Width 15 mm
Height 73 mm
Depth 58 mm
Weights
Weight, approx. 31 g
last modified: 12/09/2020
6ES7135-6TD00-0CA1 Subject to change without notice
Page 4/4 12/10/2020 © Copyright Siemens
