82M and TCC

Enclosed Pneumatic Power Clamps | Heavy-Duty, Tolerance Compensation | Product Overview

82M Series Enclosed Power Clamp

Shown with optional U-Arms
and Cylinders with Internal
Hold Open Device

“B” Front Mount available for

82M and TCC size 40mm
Same mounting pattern as size
50 and 63mm

80mm 63mm 50mm 40mm

Max Holding Torque Max Holding Torque Max Holding Torque Max Holding Torque
3000 Nm 1800 Nm 1300 Nm 380 Nm
Max Clamping Torque Max Clamping Torque Max Clamping Torque Max Clamping Torque
850 Nm at 5bar 420 Nm at 5bar 270 Nm at 5bar 120 Nm at 5bar

NAAMS Lateral Mounting

available on 82M and TCC
in addition to narrow, wide
TCC Tolerance Compensating Power Clamp
and NAAMS Clamp Arm Shafts
Shown with optional U-Arms
and Cylinders with Internal
Hold Open Device

Tolerance
compensation
for variable part
thicknesses

• T olerance compensation for variable

63mm 50mm 40mm sheet metal thicknesses within three
Max Holding Torque Max Holding Torque Max Holding Torque degrees of arm movement
295 Nm 175 Nm 85 Nm
Max Clamping Torque Max Clamping Torque Max Clamping Torque • There is no need for shimming
295 Nm at 5bar 175 Nm at 5bar 85 Nm at 5bar

PC-PPC | 27 Dimensions and technical information are subject to change without notice
 82M and TCC
Enclosed Pneumatic Power Clamps | Heavy-Duty, Tolerance Compensation | Product Overview

Adjusting the Arm Opening Angle

Easily adjust arm opening angle with an M5 Allen wrench.

• Move clamp arm to full open position.
• Using Allen wrench, release mechanism (leave Allen wrench in place).
• Move clamp arm to desired opening.
• Tighten to 20 Nm.

Enclosed Power Clamp Hand Lever (82M-3E Models Only)

Standard Adjustable Hand Lever Weldable Hand Lever

Hand lever •  and lever can be welded into a permanent

H
position can position.
be adjusted • Handle can be mounted on the left or right side
20° up or down

•  and lever position is adjustable for improved ergonomics

H
• Handle can be mounted on the left or right side

Dimensions and technical information are subject to change without notice PC-PPC | 28
TCC-2
Enclosed Pneumatic Power Clamps | Heavy-Duty, Tolerance Compensation | Ordering Information

TCC-2 E 03 00 6A L8

Mounting Description Clamp Arm Shaft Description Hand Lever Description

E Standard Mounting 03 for U-Arms 00 No Hand lever
Common Front Mount for Size 40 only 23 for Lateral Arms
B
(same mount pattern as size 50 & 63) See below for further details
N NAAMS Side Mounting for Size 63 only

Mounting

E • Tolerance compensation
for variable sheet metal
thicknesses within three
Tolerance
degrees of arm movement
compensation
for variable part • There is no need
thicknesses for shimming

Size 40

Size 50

Size 63
Clamp Arm Shaft
B
03

Size Shaft Length (L17)

40 9 mm [0.35 in]
50 12 mm [0.47 in]
63 12 mm [0.47 in]
Size 40 Only

N 23

Size Shaft Length (L17)

40 16 mm [0.63 in] Shown with U-Arm
50 21 mm [0.83 in] 8UM634-25-144
63 21 mm [0.83 in] (order separately)
Size 63 Only

PC-PPC | 29 Dimensions and technical information are subject to change without notice
 TCC-2
Enclosed Pneumatic Power Clamps | Heavy-Duty, Tolerance Compensation | Ordering Information

Sensor Description
L8/N8 L9/N9
00 Without Sensing System
L8* PNP Sensor with In-line M12x1 Connector (8EA-146-4-B)
N8* NPN Sensor with In-line M12x1 Connector (8EA-154-4-B)
L9 PNP Sensor with 90° M12x1 Connector (8EA-147-4-B)
N9 NPN Sensor with 90° M12x1 Connector (8EA-155-4-B)
K8 PNP Sensor with M12x1 Cable Connector (8EA-158-4-B)
K9 NPN Sensor with M12x1 Cable Connector (8EA-167-4-B)
*Not available for use with 4V, 5V, 6V cylinder option.
K8/K9

Cylinder (Standard) Cylinder with Unlockable Return Valve

40 40 mm Cylinder (G1/8 Port) 4C 40 mm Cylinder (G1/8 Port)
50 50 mm Cylinder (G1/4 Port) 5C 50 mm Cylinder (G1/4 Port)
5N 50 mm Cylinder (1/4-18 NPT Port) 5D 50 mm Cylinder (1/4-18 NPT Port)
63 63 mm Cylinder (G1/4 Port) 6C 63 mm Cylinder (G1/4 Port)
6N 63 mm Cylinder (1/4-18 NPT Port) 6D 63 mm Cylinder (1/4-18 NPT Port)

Cylinder with Internal Hold Open Device

4A 40 mm Cylinder (G1/8 Port)
5A 50 mm Cylinder (G1/4 Port) Cylinder with Piston Rod Locking Device
5B 50 mm Cylinder (1/4-18 NPT Port) 4V 40 mm Cylinder (G1/8 Port)
6A 63 mm Cylinder (G1/4 Port) 5V 50 mm Cylinder (G1/4 Port)
6B 63 mm Cylinder (1/4-18 NPT Port) 6V 63 mm Cylinder (G1/4 Port)

40 50 63
Max Holding/ Max Holding/ Max Holding/
Clamping Torque Clamping Torque Clamping Torque
85 Nm [62.7 ft-lb] 175 Nm [129 ft-lb] 295 Nm [217.6 ft-lb]
at 5 bar [72 psi] at 5 bar [72 psi] at 5 bar [72 psi]

Dimensions and technical information are subject to change without notice PC-PPC | 30
 TCC-2
Enclosed Pneumatic Power Clamps | Heavy-Duty, Tolerance Compensation | Technical Specifications

Max. Clamping Air Consumption per double

Cylinder Ø Weight
Model Holding Torque Torque at 5 bar
(mm) (kg)
stroke at 5 bar
(Nm) (Nm) (liter)

TCC-2.....40..
TCC-2.....4A.. 1,6
TCC-2.....4B.. 85 85 40 0,9
TCC-2.....4C.. 1,7
TCC-2.....4V.. 1,6

Maximum Tooling Weight Maximum Clamping Force Air Consumption Control Flow
3.0 1200 3
6 bar 1 0,5 sec
2.5 1000 2,5 Open
Clamping force (N)

Air consumption per

double stroke (Nl)
5 bar 0

2.0 4 bar
800 2
Weight [kg]

1
opening / closing 3 bar Signal opened 0,5 sec.
time 2 sec 0
1.5 600 1,5
1
Close
1.0 400 1 0

1
0.5 200 0,5 Signal closed
opening / closing 0
time 1 sec
0 0 0
100 125 150 175 200 100 125 150 175 200 15° 30° 45° 60° 75° 90° 105° 120° 135°
Distance from pivot point Length of the clamping arm (mm) Opening angle (°) Internal Hold Open Device
to center of mass [mm] 4A Cylinder Option
ATTENTION: Calculation tool available. Please consult factory.

Max. Clamping Air Consumption per double

Cylinder Ø Weight
Model Holding Torque Torque at 5 bar
(mm) (kg)
stroke at 5 bar
(Nm) (Nm) (liter)

TCC-2E....50..
TCC-2E....5N..
2,8
TCC-2E....5A..
TCC-2E....5B.. 175 175 50 1,6
TCC-2E....5C..
3,0
TCC-2E....5D..
TCC-2E....5V.. 2,9

Maximum Tooling Weight Maximum Clamping Force Air Consumption Control Flow
10 2500 3
9 6 bar 1 0,5 sec
2,5 Open
Clamping force (N)

Air consumption per

8
double stroke (Nl)

2000 5 bar 0
7 4 bar 2
Weight [kg]

1
6 1500 3 bar Signal opened 0,5 sec.
opening / closing time 2 sec 0
5 1,5
1
4 1000 Close
1 0
3
2 500 1
0,5 Signal closed
1 0
opening / closing time 1 sec
0 0 0
100 125 150 175 200 225 250 275 300 100 125 150 175 200 15° 30° 45° 60° 75° 90° 105° 120° 135°
Distance from pivot point Length of the clamping arm (mm) Opening angle (°) Internal Hold Open Device
to center of mass [mm] 5A/5B Cylinder Option
ATTENTION: Calculation tool available. Please consult factory.

PC-PPC | 31 Dimensions and technical information are subject to change without notice
 TCC-2
Enclosed Pneumatic Power Clamps | Heavy-Duty, Tolerance Compensation | Technical Specifications

Max. Clamping Air Consumption per double

Cylinder Ø Weight
Model Holding Torque Torque at 5 bar
(mm) (kg)
stroke at 5 bar
(Nm) (Nm) (liter)

TCC-2.....63..
3,8
TCC-2.....6N..
TCC-2.....6A..
4,0
TCC-2.....6B.. 295 295 63 2,6
TCC-2.....6C..
4,6
TCC-2.....6D..
TCC-2.....6V.. 4,2

Maximum Tooling Weight Maximum Clamping Force Air Consumption Control Flow
14 4000 3
6 bar 1 0,5 sec
12 3500
2,5 Open
Clamping force (N)

Air consumption per

5 bar

double stroke (Nl)

0
10 3000
4 bar
2
Weight [kg]

1
2500 3 bar Signal opened 0,5 sec.
8
opening / closing 0
time 2 sec 2000 1,5
6 1
1500 Close
1 0
4
1000
1
2 0,5 Signal closed
opening / closing 500
0
time 1 sec
0 0 0
100 125 150 175 200 225 250 275 300 100 125 150 175 200 15° 30° 45° 60° 75° 90° 105° 120° 135°
Distance from pivot point Length of the clamping arm (mm) Opening angle (°) Internal Hold Open Device
to center of mass [mm] 6A/6B Cylinder Option
ATTENTION: Calculation tool available. Please consult factory.

Center of Mass

A B
Model Weight
Closed Open Closed Open
TCC-2E....40.. 23 55 69
24 1,5
TCC-2B....40.. 24 54 68
TCC-2E....4A.. 22 86
A A A
23 72 C 1,6
A
TCC-2B....4A.. 23 85
TCC-2E....4C.. 25 77 89
26 1,7
TCC-2B....4C.. 26 76 88
TCC-2E....4V.. 80
24 24 66 1,6
B

TCC-2B....4V.. 79
B

B
B

TCC-2E....50..
70 87 2,6
TCC-2E....5N..
24 25
TCC-2E....5A..
83 99 2,8
TCC-2E....5B..
TCC-2E....5C..
27 27 96 110 3,0
TCC-2E....5D..
TCC-2E....5V.. 25 26 84 99 2,9
TCC-2.....63..
closed position opened position (135°) closed position 89
opened position (135°) 105 3,7
TCC-2.....6N..
27 28
TCC-2.....6A..
98 114 3,9
TCC-2.....6B..
TCC-2.....6C..
30 30 116 130 4,4
TCC-2.....6D..
TCC-2.....6V.. 28 28 103 119 3,9

Dimensions and technical information are subject to change without notice PC-PPC | 32
82M-3
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Ordering Information

82M-3 E 23 H0 50 L8

Mounting Description Clamp Arm Shaft Description Hand Lever Description

E Standard Mounting 03 for U-Arms 00 No Hand lever
Common Front Mount for Size 40 only for U-Arms (required H0 Hand Lever
B 13
(same mount pattern as size 50 & 63) for 40 NAAMS N only) HS Weldable
N NAAMS Side Mounting for Size 40 & 63 only 23 for Lateral Arms See below for further details
for Lateral Arms
D0
(size 63 NAAMS N only)
Mounting
See below for further details
E
Clamp Arm Shaft

03

Size 40

Size Shaft Length (L17)

40 9 mm [0.35 in]
50 12 mm [0.47 in]
63 12 mm [0.47 in]

Size 50 13 Hand Lever

E H0

Size Shaft Length

40 9 mm [0.35 in]
Size 63/80

B 23/D0

Size 40 Only 23 Shown with U-Arm

HS 8UM504-25-144
Size Shaft Length (L17)
N 40 16 mm [0.63 in]
(order separately)
Hand Lever Description
50 21 mm [0.83 in]
00 No Hand Lever
63 21 mm [0.83 in]
80 32 mm [1.26 in] Standard Hand Lever
H0 (not compatible with
cylinder options *A, *B)
D0
Size Shaft Length (L17) Weldable Hand Lever
HS (not compatible with
Size 40/63 Only 63 26 mm [1.02 in] cylinder options *A, *B)

PC-PPC | 33 Dimensions and technical information are subject to change without notice
 82M-3
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Ordering Information

Sensor Description L8/N8 L9/N9

00 Without Sensing System
L8 PNP Sensor with In-line M12x1 Connector (8EA-146-4-B)
N8 NPN Sensor with In-line M12x1 Connector (8EA-154-4-B)
L9 PNP Sensor with 90° M12x1 Connector (8EA-147-4-B)
N9 NPN Sensor with 90° M12x1 Connector (8EA-155-4-B)
K8 PNP Sensor with M12x1 Cable Connector (8EA-158-4-B)
K9 NPN Sensor with M12x1 Cable Connector (8EA-167-4-B) K8/K9

Cylinder - Standard Cylinder with Internal Hold Open Device

40 40 mm Cylinder (G1/8 Port) 4A 40 mm Cylinder (G1/8 Port)
50 50 mm Cylinder (G1/4 Port) 5A 50 mm Cylinder (G1/4 Port)
5N 50 mm Cylinder (1/4-18 NPT Port) 5B 50 mm Cylinder (1/4-18 NPT Port)
63 63 mm Cylinder (G1/4 Port) 6A 63 mm Cylinder (G1/4 Port)
6N 63 mm Cylinder (1/4-18 NPT Port) 6B 63 mm Cylinder (1/4-18 NPT Port)
80 80 mm Cylinder (G1/4 Port) 8A 80 mm Cylinder (G1/4 Port)
8N 80 mm Cylinder (1/4-18 NPT Port) 8B 80 mm Cylinder (1/4-18 NPT Port)

40 50 63 80
Max Holding Torque Max Holding Torque Max Holding Torque Max Holding Torque
380 Nm [280 ft-lb] 1300 Nm [959 ft-lb] 1800 Nm [1328 ft-lb] 3000 Nm [2213 ft-lb]
Max Clamping Torque Max Clamping Torque Max Clamping Torque Max Clamping Torque
120 Nm [89 ft-lb] 270 Nm [199 ft-lb] 420 Nm [310 ft-lb] 850 Nm [627 ft-lb]
at 5 bar [72 psi] at 5 bar [72 psi] at 5 bar [72 psi] at 5 bar [72 psi]

Dimensions and technical information are subject to change without notice PC-PPC | 34
 82M-3
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Technical Specifications

Max. Clamping Air Consumption per double

Cylinder Ø Weight
Model Holding Torque Torque at 5 bar
(mm) (kg)
stroke at 5 bar
(Nm) (Nm) (liter)
82M-3E....4...
82M-3B....4... 380 120 40 1,5 0,9
82M-3N....4...

Maximum Tooling Weight Maximum Clamping Force Air Consumption Control Flow
3.0 1400 7

5 bar 1 0,5 sec

2.5 1200 6 Open
Clamping force (N)

Air consumption per

double stroke (Nl)
4 bar 0
1000 5
2.0 3 bar
Weight [kg]

1
opening / closing Signal opened 0,5 sec.
time 2 sec 800 4 0
1.5
600 3 1
Close
1.0 0
400 2
1
0.5 200 1 Signal closed
opening / closing 0
time 1 sec
0 0 0
100 125 150 175 200 100 125 150 175 200 15° 30° 45° 60° 75° 90° 105° 120° 135°
Distance from pivot point Length of the clamping arm (mm) Opening angle (°) Internal Hold Open Device
to center of mass [mm] 4A Cylinder Option
ATTENTION: Calculation tool available. Please consult factory.

Max. Clamping Air Consumption per double

Cylinder Ø Weight
Model Holding Torque Torque at 5 bar
(mm) (kg)
stroke at 5 bar
(Nm) (Nm) (liter)
82M-3E....5... 1300 270 50 2,8 1,6

Maximum Tooling Weight Maximum Clamping Force Air Consumption Control Flow
10 3000 7
9 1 0,5 sec
5 bar 6
2500 Open
Clamping force (N)

Air consumption per

8
double stroke (Nl)

4 bar 0
7 5
2000 3 bar
Weight [kg]

1
6 Signal opened 0,5 sec.
opening / closing time 2 sec 4 0
5 1500
4 3 1
Close
3 1000 0
2
2 1
500 1 Signal closed
1 0
opening / closing time 1 sec
0 0 0
100 125 150 175 200 225 250 275 300 100 125 150 175 200 225 250 275 300 15° 30° 45° 60° 75° 90° 105° 120° 135°
Distance from pivot point Length of the clamping arm (mm) Opening angle (°) Internal Hold Open Device
to center of mass [mm] 5A/5B Cylinder Option
ATTENTION: Calculation tool available. Please consult factory.

Max. Clamping Air Consumption per double

Cylinder Ø Weight
Model Holding Torque Torque at 5 bar
(mm) (kg)
stroke at 5 bar
(Nm) (Nm) (liter)
82M-3E....6...
1800 420 63 3,8 2,6
82M-3N....6...

Maximum Tooling Weight Maximum Clamping Force Air Consumption Control Flow
14 4500 7

12 4000 5 bar 6
1 0,5 sec
Open
Clamping force (N)

Air consumption per

double stroke (Nl)

3500 4 bar 0
10 5
3000 3 bar
Weight [kg]

1
8 4 Signal opened 0,5 sec.
opening / closing 2500 0
time 2 sec
6 2000 3 1
Close
1500 0
4 2
1000 1
2 1 Signal closed
opening / closing 500 0
time 1 sec
0 0 0
100 125 150 175 200 225 250 275 300 100 125 150 175 200 225 250 275 300 15° 30° 45° 60° 75° 90° 105° 120° 135°
Distance from pivot point Length of the clamping arm (mm) Opening angle (°) Internal Hold Open Device
to center of mass [mm] 6A/6B Cylinder Option
ATTENTION: Calculation tool available. Please consult factory.

PC-PPC | 35 Dimensions and technical information are subject to change without notice
 82M-3
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Technical Specifications

Max. Clamping Air Consumption per double

Cylinder Ø Weight
Model Holding Torque Torque at 5 bar
(mm) (kg)
stroke at 5 bar
(Nm) (Nm) (liter)
82M-3E....80..
8,7
82M-3E....8N..
3000 850 80 6,3
82M-3E....8A..
8,8
82M-3E....8B..

Maximum Tooling Weight Maximum Clamping Force Air Consumption Control Flow
25 9000 7

8000 5 bar 6
1 0,5 sec
Open
Clamping force (N)

Air consumption per

20

double stroke (Nl)

7000 4 bar 0
5
6000 3 bar
Weight [kg]

1
15 Signal opened 0,5 sec.
5000 4 0
opening / closing
time 2 sec 4000 3 1
10 Close
3000 0
2
2000 1
5
1 Signal closed
opening / closing 1000 0
time 1 sec
0 0 0
100 150 200 250 300 350 400 100 150 200 250 300 350 400 15° 30° 45° 60° 75° 90° 105° 120° 135°
Distance from pivot point Length of the clamping arm (mm) Opening angle (°) Internal Hold Open Device
to center of mass [mm] 8A/8B Cylinder Option
ATTENTION: Calculation tool available. Please consult factory.

Center of Mass

A A A A A A C C
A A

B
B
B
B

B
B
B
B

closed positionclosed position

opened opened
position (135°) position (135°) closed positionclosed position
opened opened
position (135°) position (135°)

Without Handle With Handle

A B A B C
Model Weight Model Weight
Closed Open Closed Open Closed Open Closed Open
82M-3E....40.. 82M-3E....40.. 22 25 49 70
23 55 69 1,6
82M-3N....40.. 24 1,5 82M-3B....40.. 24 27 46 67
4
82M-3B....40.. 24 54 68 82M-3E....50..
23 30 62 85 3,1
82M-3E....4A.. 22 86 82M-3E....5N..
23 72 1,6
82M-3B....4A.. 23 85 82M-3.....63..
26 30 80 102 3 4,2
82M-3E....50.. 82M-3.....6N..
70 87
82M-3E....5N.. 82M-3E....80..
24 25 2,8 35 38 93 122 2 9,2
82M-3E....5A.. 82M-3E....8N..
83 99
82M-3E....5B..
82M-3.....63..
88 103 3,8
82M-3.....6N..
27 28
82M-3.....6A..
98 114 3,9
82M-3.....6B..
82M-3E....80..
98 123 8,7
82M-3E....8N..
36 37
82M-3E....8A..
104 129 8,9
82M-3E....8B..

Dimensions and technical information are subject to change without notice PC-PPC | 36
82M-3N13, 40mm
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions

82M-3N13..40..

97 Dimensions of the
19 85 driven shaft

SW16 h9

50 ±0,1
54,5
9
33

82,5
60±0,1
±0,1

8
12±0,1 35 ±0,02 for Ø6H7

34,5
Pivot point
7,5±0,1
25±0,05

45±0,1

15 3,5
38,5 ±0,1
35 ±0,1

47±0,1

M6
±0,02 for Ø6H7

136
±0,02 for Ø6H7

10 3,5
+0,1
0

16 10
98

40

±0,1
25

8 N9

21 33 4
±0,1

Ø6 H7

M6

10
25

Ø6H7
10
Ø6H7

mm [INCH] mm [INCH]

See page PC-PPC-40 for

THIRD ANGLE
PROJECTION
FIRST ANGLE
PROJECTION
4 cylinder options 40 and 4A.

with Handle Option

82M-3N13H*40**

Power by compressed air, max. 6 bar operation with oil-free air is permissible.
The connector socket and the cable are not supplied with the unit.

PC-PPC | 37 Dimensions and technical information are subject to change without notice
 U-Arms Center (Steel)
82M-3N13, 40mm accessories
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions and Technical Specifications

45 For Size 40mm NAAMS*

Ø7 20 U-Arm (Steel)
Ø6H7
90° Right
16

(7) 80
20 ±0,02 90,1±0,1

180° version
Opening 180° Right
L5 Area of interference
117 Hold-down piece
must not protrude
22 ±0,1

0
in the interior area "R70"
~R7

due to the area of

interference
90° version
Opening
L5

8UM408-00-117
+0,020 8UM408-15-117
SW16 - 0,009
8UM408-25-117
8UM408-45-117
Pivot point
Arm Max. Opening Max. Opening Weight
L5
Model No. 90º Version 180º Version (kg)
8UM408-00-117 105º 0,46 0
8UM408-15-117 135° 120º 0,51 15
8UM408-25-117 0,52 25
135°
8UM408-45-117 130° 0,58 45
*Compatible with NAAMS Clamp Arm Shaft option 13 only.

117 ±1,5 Counter Support

20 ±0,02
90 ±0,1
20

View:
16

Counter support
without screws and pins Ø7
Ø6 H7
(2x)
(2x)
Pivot point
Holding force
6,5

38,5
Ø6 H7
(2x)

40
45

19

Deformation
25 ±0,1

22,7
±0,1
(4x)
Ø7

38

2
22

35 ±0,1
48 f. Ø6H7 ±0,02 Arm Holding Force Deformation Weight
Model No. (N) (mm) (kg)
82ZB-190-1 2000 0,4 0,22

For Handle and Anti-Ramming device Accessories see pages PC-PPC-47 & 48.

Dimensions and technical information are subject to change without notice PC-PPC | 38
82M-3./TCC-2, 40mm
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions

82M-3E/TCC-2E....4. 97 Dimensions of the

driven shaft
19 85

L17

B23 max.
50 ±0,1

SW16 h9
33
B23
Model L17
Max.
82M-3.03/TCC-2.03..4... 54,5 9
TCC-2 Series 82,5 82M-3.23/TCC-2.23..4... 66,5 16
-3° tolerance
compensation. 60±0,1

8,5
±0,1
12±0,1 35 ±0,02 for Ø6H7

34,5
Pivot point
7,5±0,1
25±0,05

45±0,1

15 3,5

38,5 ±0,1
35 ±0,1

47±0,1

M6
±0,02 for Ø6H7

136
±0,02 for Ø6H7
10 3,5
+0,1
0

16 10
98

40

±0,1
25

8 N9
21 33 4
±0,1

Ø6 H7

M6

10
25

Ø6H7
10

mm [INCH] mm [INCH]

THIRD ANGLE FIRST ANGLE Power by compressed air, max. 6 bar operation with oil-free air is permissible.
PROJECTION PROJECTION The connector socket and the cable are not supplied with the unit.
Safe “holding/clamping” only under pressurization (for TCC models only).

82M-3B/TCC-2B....4. Dimensions below for “B” mounting surfaces. See above for additional base unit dimensions.

10
±0,1

M6
7,5

8
36,5
11±0,1

±0,1
45 ±0,1

±0,05

30 ±0,02 for Ø8H7

47±0,1
63,5 ±0,1

10
1,5
Ø8 H7

5
Ø6H7

+0,1
0
32±0,1

55
8 N9

25 ±0,1

"X"
4,5
10
M8

12

View "X"

PC-PPC | 39 Dimensions and technical information are subject to change without notice
 82M-3./TCC-2, 40mm
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Cylinder Options Dimensions

82M-3/TCC-2.....40 82M-3/TCC-2.....4A
Standard Cylinder Cylinder with Internal Hold Open Device
Securely holds clamp in the open position.

265
251
Internal Open
Holding Device:
115

For manual

129
G 1/8 unlocking this G 1/8
area has to be
accessible.

30
65 34

74,5 34

TCC-2.....4C TCC-2.....4V
Cylinder with Unlock-able Return Valve Cylinder with Rod Locking Device
Pneumatically holds clamp arm in the Uses friction to clamp rod at any point
closed position when air is released. between open and closed positions.
275

M5
274,6

70,3
To centerline
Manual of pivot point
139

Unlocking
138,6

G 1/8

2 G 1/8
21
2
1 14
12
80 34 65 34
4 2 4 2
14 12
14 12
51 3
5 1 3

Dimensions and technical information are subject to change without notice PC-PPC | 40
82M-3/TCC-2, 50mm
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions

82M-3E/TCC-2E....5. 107
Dimensions of the
26,5 95 driven shaft

B23 max.
L17

48 ±0,1

SW19 h9
47,6

B23
L17
Model
Max.
82M-3E03/TCC-2E03..5... 72 12
82M-3E23/TCC-2E23..5... 90 21
111,5
80±0,1
13±0,1
10±0,1

9,5
48

Pivot point

5
36,5±0,05

63,5 ±0,1

11 ±0,1

9
55 ±0,1

71,5 ±0,1 30±0,1

21,5

M10
±0,02 for Ø8H7
170

12 3,5
32 ±0,1
+0,1
125

55 0

25
±0,02 for Ø10H7

13 9,5
45 ±0,1

10
12 N9

12
M8
Ø8 H7

5 50±0,1

Ø10 H7
±0,02 for Ø10H7

5 45±0,1
±0,02 for Ø8H7

TCC-2 Series
-3° tolerance
compensation.

mm [INCH] mm [INCH]
10 deep
Ø8 H7

40 ±0,1

THIRD ANGLE FIRST ANGLE

PROJECTION PROJECTION
±0,02 for Ø8H7
45±0,1
10 deep
M8

Power by compressed air, max. 6 bar operation with oil-free air is permissible.
The connector socket and the cable are not supplied with the unit.
Safe “holding/clamping” only under pressurization (for TCC models only).

PC-PPC | 41 Dimensions and technical information are subject to change without notice
 82M-3/TCC-2, 50mm
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Cylinder Options Dimension

82M-3E/TCC-2E....50/5N 82M-3E/TCC-2E....5A/5B
Standard Cylinder Cylinder with Internal Hold Open Device
Securely holds clamp in the open position.

316

325
14,2
To centerline
of pivot point
146

Internal Open
Holding Device: C

155
C For manual
unlocking this
area has to be
accessible.
72 44
78,5 44
Ports C Important! For optimal cushioning, Ports C
external pneumatic one-way flow Important! For optimal cushioning,
50 G1/4 5A G1/4 external pneumatic one-way flow
control valves should be used.
5N 1/4-18 NPT 5B 1/4-18 NPT control valves should be used.

TCC-2E....5C/5D TCC-2E....5V
Cylinder with Unlock-able Return Valve Cylinder with Rod Locking Device
Pneumatically holds clamp arm in the Uses friction to clamp rod at any point
closed position when air is released. between open and closed positions.
342

G1/8 344

88,8
Manual To centerline
Unlocking of pivot point
174
172

G1/4

2
C
21
2
1 14
12

89,5 4 2 44 72 14
4 2
12
44
14 12
51 3
Important! For optimal
5 1 3
Ports C
cushioning,external pneumatic
5C G1/4 one-way flow control valves
5D 1/4-18 NPT should be used.

Dimensions and technical information are subject to change without notice PC-PPC | 42
82M-3./TCC-2, 63mm
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions

82M-3/TCC-2.....6.

112,5

26,5 101,5

Dimensions of the
driven shaft

B23 max.
54 ±0,1
52

7
L1

SW22 h9
B7a B23
Model L17
±0,1 Max.
82M-3E03/TCC-2E03..6... 50
78 12
82M-3N03/TCC-2N03..6... 55
82M-3E23/TCC-2E23..6... 50
96 21
82M-3N23/TCC-2N23..6... 55
82M-3ND0..6... 55 106 26
111,5
80 ±0,1

70,5 (TCC Only)

TCC-2 Series 13±0,1
11,5

-3° tolerance
compensation. 10±0,1

54

Pivot point

5
36,5 ±0,05

63,5 ±0,1

11±0,1

55 ±0,1

9 30
71,5±0,1

±0,1
±0,02 for Ø8H7 M10
187

12 3,5
32 ±0,1
+0,1
0
137

10
±0,02 for Ø10H7

8,5
55

45 ±0,1

B7a
±0,02 for Ø10H7
10
12
12 N9
M8
H7
Ø8

Ø10 H7

mm [INCH] mm [INCH]

THIRD ANGLE FIRST ANGLE

PROJECTION PROJECTION Power by compressed air, max. 6 bar operation with oil-free air is permissible.
The connector socket and the cable are not supplied with the unit.
Safe “holding/clamping” only under pressurization (for TCC models only).

PC-PPC | 43 Dimensions and technical information are subject to change without notice
 82M-3./TCC-2, 63mm
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Cylinder Options Dimension

82M-3/TCC-2.....63/6N 82M-3/TCC-2.....6A/6B
Standard Cylinder Cylinder with Internal Hold Open Device
Securely holds clamp in the open position.

351

350
Internal Open
Holding Device:
C For manual C
164

163
unlocking this
area has to be
accessible.

100 52 100 52

Ports C Important! For optimal cushioning, Ports C Important! For optimal cushioning,
external pneumatic one-way flow external pneumatic one-way flow
63 G1/4 6A G1/4
control valves should be used. control valves should be used.
6N 1/4-18 NPT 6B 1/4-18 NPT

TCC-2.....6C/6D TCC-2.....6V
Cylinder with Unlock-able Return Valve Cylinder with Rod Locking Device
Pneumatically holds clamp arm in the Uses friction to clamp rod at any point
closed position when air is released. between open and closed positions.

378,5
370

G1/8

93,3
To centerline
Manual of pivot point
Unlocking
191,5

G1/4
183

C
2

21
2
1 14
12
117 4 2 52 100 4 2 52
14 12
14 12
51 3
5 1 3 Ports C Important! For optimal
cushioning,external pneumatic
6C G1/4 one-way flow control valves
6D 1/4-18 NPT should be used.

Dimensions and technical information are subject to change without notice PC-PPC | 44
82M-3., 80mm
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions

82M-3E....8.

140
35 128
Plan view
Dimensions of
the driven shaft

76 ±0,1

140
72

h9
32

SW28
153
21 113±0,1
±0,1 76
8

15 ±0,1

Pivot point
50 ±0,05

5
15 ±0,1

65 ±0,1
90 ±0,1

5 15
96,5 ±0,1
245

15 70 ±0,1
50±0,1
175
+0,1

±0,02 for Ø8H7

0

M12

±0,02 for Ø12H7

±0,02 for Ø12H7
80

75±0,1
50 ±0,1

3,5 15
12 N9

15
M10
Ø8 H7

5
Ø12 H7

mm [INCH] mm [INCH]

THIRD ANGLE FIRST ANGLE

PROJECTION PROJECTION

Power by compressed air, max. 6 bar operation with oil-free air is permissible.
The connector socket and the cable are not supplied with the unit.

PC-PPC | 45 Dimensions and technical information are subject to change without notice
 82M-3., 80mm
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Cylinder Options Dimension

82M-3E....80/8N 82M-3E....8A/8B
Standard Cylinder Cylinder with Internal Hold Open Device
Securely holds clamp in the open position.

430 4,7

437
Internal Open
Holding Device:
For manual
unlocking this
area has to be
accessible.
C
185

192
32

134 66 134 66

Ports C Important! For optimal cushioning, Ports C Important! For optimal cushioning,
80 G1/4 external pneumatic one-way flow 8A G1/4 external pneumatic one-way flow
control valves should be used. control valves should be used.
8N 1/4-18 NPT 8B 1/4-18 NPT

Dimensions and technical information are subject to change without notice PC-PPC | 46
 ±10°
Hand lever left Hand lever right

82M-3. accessories
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions and Technical Specifications
~R
1

Hand Lever ±10°

Hand lever left Hand lever right

~a
2
~R
L20

11 ±10°
±10°
1

Hand
Hand
lever
lever
leftleft

Ø38
~a~R1
E**H040**

~R
2
1111

1
L20

Ø38

Ø38

~a
~a
B28

2
2
82M-3E**H040**
L20
L20

B21
20° 20° 838
Ø3Ø

Ø38
Ø38
60°
Pneumatic circuit required for
manual and pneumatic actuation.

82M-3E**H040**
82M-3E**H040**
open B28

B21
20° 20°
60°
closed Pneumatic circuit required for
manual and pneumatic actuation.
g of the hand lever: Hand lever can be B28
B28
e in 60° increments. mounted in 3 positions. Note: Hand lever is supplied unassembled. Allows for easy,
custom left hand or right hand mountingopen
for desired position.
B21
B21
20°20° 20°20°
60°60°
Pneumatic circuit
Pneumatic required
circuit for for
required
manual andand
manual pneumatic
pneumatic actuation.
actuation.
closed

Mounting of the hand lever: Hand lever can be open

open
rotatable in 60° increments. mounted in 3 positions.
Hand lever
position is
adjustable to
±20
closed
degrees
closed
for improved
Mounting
Mountingof the
of the
hand
hand
lever:
lever: Hand
Hand
lever
lever
cancan
be be ergonomics.
rotatable
rotatable
in 60°
in 60°
increments.
increments. mounted
mountedin 3inpositions.
3 positions.

Swivel Angle a2
Model No. (with reference to opening angle of clamp arm)
B21 B28 L20 ~R1 0° 15° 30° 45° 60° 75° 90° 105° 120° 135°
82M-3...H040.. 27 24 48,5 160 0° 31° 41° 49° 58° 69° 88° 113° 134° 144°
82M-3...H05... 52 20 70 218 -1° 30° 39° 46° 53° 61° 70° 81° 92° 103°
82M-3...H06.. 52 20 70,5 218 0° 30° 39° 47° 56° 66° 79° 94° 108° 119°
82M-3...H08.. 56 24 82 268 -1° 28° 37° 45° 53° 63° 75° 92° 107° 117°

PC-PPC | 47 Dimensions and technical information are subject to change without notice
 82M-3. accessories
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions and Technical Specifications

Situation of installation:
handlever left-hand side
Situation of installation:
handlever right-hand side
~a2 Locking Device
locking device right-hand side locking device left-hand side L5 for Hand Lever
180° version

Adjustment of locking device

at opening angle 135°

a1
~R
1
90° version

R3

B6
B3
B2
D1

~R
2

B4 B1
~B5
Limited Setting Options
Height of the clamping arm: L5 max.
B1 B2 B3 B4 B5 B6 ØD1 R1 R2 R3 a2
Order No. For Model 90° version 180° version
~ ~ ~ ~
45 75 00 15 25 45
82ZB-162-1 82M-3...H040..* 50 11 48,5 25Order31
No. 38,5For10,5
Model 81 B1 160
B2 27 B4 6 B5 120°
B3 B6 ØD1 –R1 R2 105° R3 120°
a1 a2120° Limited
120°setting options at 180
Height of the clamping arm
82ZB-084-1 82M-3...H05... 48 7 70 30 36 55 11,5 107 218 32,5 6 ~ 120° –~ ~ – max.
105° ~120° 00 – 15
82ZB-039-1 82M-3...H06... 54 9 70,5 3082ZB-162-1
36 82M-3E**H040**
55 11,5 107 50 210 11 48,5 25 6 31 110°
32,5 38,5 10,5
105°81 160 – 27 105° 6120°max.105° – max.120°
82ZB-084-1 82M-3E**H05*** 48 7 70 30 36 55 11,5 107 218 32,5 135° 5 - max.105°
*Not compatible with Size 40 Option N NAAMS Side Mounting. 82ZB-039-1 82M-3E**H06*** 54 9 70,5 30 36 55 11,5 107 210 32,5 5 - max.105°

Anti-Ramming Device
B3

Pivot point

B4
Anti-ramming device
is only available for
standard cylinder
B5

with 82M-3...00..00
and 82M-3...00..L8

Order No. For Model B1 B2 B3 B4 B5

8AB-151-1 82M-3.....40.. 53 66,5 89,5 65,5 210,5

8AB-152-1 82M-3.....5... 51 73 100 92,5 271
8AB-153-1 82M-3.....6... 57 79 120 104,5 296
B1
8AB-154-1 82M-3.....8... 79 105,5 148 142,5 360 B2

Cable and Connector

Order No. Description

8EL-002-1 M12x1, Straight, 5-pin Connector with 5m Cable

8EL-003-1 M12x1, Angular, 4-pin Connector with 5m Cable
8EL-002-1 8EL-003-1

Dimensions and technical information are subject to change without notice PC-PPC | 48
U-Arms Center (aluminum) U-Arms Center (Aluminium)

Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions and Technical Specifications

For Size 40mm* 90°

45
20
6 H7

+ 0,2
34,6 0
16

(7) B26
20 ±0,02 B11 180°
180° version
L5 Area of interference
B2 Hold-down piece
must not protrude
22 ±0,1

~ R70 in the interior area "R70"

due to the area of
interference
90° version
Opening
L5

8UM404-00-117
+0,020
SW16- 0,009

8UM404-15-117
8UM404-25-117
Pivot point
8UM404-45-107

Arm Max. Opening Max. Opening Weight B11

B2 B26 L5
Model No. 90º Version 180º Version (kg) ±0,1

8UM404-00-117 105º 0,23 0

8UM404-15-117 135° 120º 0,24 117 90 82 15
8UM404-25-117 0,25 25
135°
8UM404-45-107 130° 0,24 107 80 72 45
*Not compatible with NAAMS Clamp Arm Shaft option 13.

For Size 50mm 90°

64,5
30 ±0,2

6 H7
9

+ 0,2
0
20

48,1

(9) 90,5
30 ±0,02 105 ±0,1
180°
180° version Area of interference
Hold-down piece
L5 must not protrude
~ R75

144 in the interior area "R75"

28 ±0,1

due to the area of

interference.
90° version

Opening
L5

8UM504-15-144
8UM504-25-144
+ 0,020
SW19 - 0,009

8UM504-45-144
Pivot point

Arm Max. Opening Max. Opening Weight

L5
Model No. 90º Version 180º Version (kg)
8UM504-15-144 105º 0,44 15
8UM504-25-144 135° 120º 0,45 25
8UM504-45-144 135° 0,48 45

PC-PPC | 49 Dimensions and technical information are subject to change without notice
 +
54,1
20
30 ±0,02
(9)
B11
B26
U-Arms Center(Aluminium)
U-Arms Center (aluminum)
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions and Technical Specifications
B4
90° 30 ±0,2 For Size 63mm
L5

~R 80
B2 6 H
7

+0,2
54,1 0
20
~19
L5 L4

(9) B26
30 ±0,02 B11
20
180°
+0,020
SW22 -0,009

±1 ,2

Dimensions are only for

Pivot point 8UM631-75-204
L5

~R 80
B2

~19
L5 L4

8UM634-15-144
8UM634-25-144
20
8UM634-45-144
+0,020
SW22 -0,009

±1
,2
8UM631-75-204* Dimension
Pivot point 8UM631-7

Arm Max. Opening Max. Opening Weight B11 L4

B2 B4 B26 L5
Model No. 90º Version 180º Version (kg) ±0,1 ±0,1

8UM634-15-144 105º 0,50 15

8UM634-25-144 120º 0,53 144 64,5 105 90,5 28 25
135°
8UM634-45-144 0,56 45
135°
8UM631-75-204* 1,7 204 82 165 107 30 75
*only steel version available.

B26
90° For Size 80mm
30±0,2
6 H7
+ 0,2
9

76,1 0
25 ±1,2

(9)
30±0,02 B11
64,5 Area of interference
180° 180° version Hold-down piece
must not protrude
in the interior area "R108"
due to the area of
B2 interference.
~ R108
35 ±0,1

9
3,5

90° version
25
±
1,2
3,5
L5

Opening
8JG-169-2-01
J7

~ 23,
SW28

8UM801-45-204 7
Pivot point

Arm Max. Opening Max. Opening Weight B11 L5**

B2 B26
Model No. 90º Version 180º Version (kg) ±0,1 ±0,2

8JG-169-2-01 105º 3,5 179 140 129 20

135°
8UM801-45-204* 135º 4,1 204 165 154 45
*only steel version available.
** Tolerance measured 80mm from pivot point.

Dimensions and technical information are subject to change without notice PC-PPC | 50
 U-Arms, left and right (Aluminium)

U-Arms Offset (aluminum)

Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions and Technical Specifications

For Size 40mm* 90° Left 90° Right

B26
U-clamp arm, right

+0,2
H7 20

34,6 0
23±0,1

7
16

(7)
20 ±0,02 B11
U-clamp arm, left 45 180° Right* 180° Left*
Area of interference
180° version Hold-down piece
must not protrude
in the interior area "R70"
L5 due to the area of
interference
B2
22 ±0,1

~R70

90° version
Opening 8UL404-00-117 8UR404-00-117
L5

8UL404-15-117 8UR404-15-117
+ 0,020
SW16 - 0,009

8UL404-25-117 8UR404-25-117
8UL404-45-107 8UR404-45-107
*90° left/180° right uses same clamp arm.
Pivot point
U-Arms, left and right
(Aluminium) 90° right/180° left uses same clamp arm.
Arm Max. Opening Max. Opening Weight B11
B2 B26 L5
Model No. 90º Version 180º Version (kg) ±0,1

8U(•)404-00-117 105º 0,23 0

8U(•)404-15-117 135° 120º 0,24 117 90 82 15
8U(•)404-25-117 0,25 25
135°
8U(•)404-45-107 130° 0,25 107 80 72 45
*Not compatible with NAAMS Clamp Arm Shaft option 13.

For Size 50mm 90,5 90° Left 90° Right

U-clamp arm, right

6 30±0,2
+0,2

H7
48,1 0

9
34 ±0,1
20

(9)
30 ±0,02 105 ±0,1
64,5 180° Right* 180° Left*
U-clamp arm, left Area of interference
180° version Hold-down piece
must not protrude
in the interior area "R75"
L5 due to the area of
~ R75

144 interference
L5 28±0,1

90°version

Opening 8UL504-15-144 8UR504-15-144

8UL504-25-144 8UR504-25-144
+ 0,020
SW19 - 0,009

8UL504-45-144 8UR504-45-144
*90° left/180° right uses same clamp arm.
Pivot point 90° right/180° left uses same clamp arm.

Arm Max. Opening Max. Opening Weight

L5
Model No. 90º Version 180º Version (kg)
8U(•)504-15-144 105º 0,45 15
8U(•)504-25-144 135° 120º 0,46 25
8U(•)504-45-144 135° 0,49 45

PC-PPC | 51 Dimensions and technical information are subject to change without notice
 U-clamp arm,
right

+ 0,2
54,1 0
U-Arms Offset (aluminum)
6 H 7 9 30 ±0,2

37±0,1
20
(9)
Enclosed Pneumatic
30
Power Clamps
B11
| Heavy-Duty Modular | Dimensions and Technical Specifications
±0,02

U-clamp arm, B4
90° Left
left 90° Right For Size 63mm
B26
Area of interference
180° version
Hold-down piece must not protrude
U-clamp arm, in the interior area "R80" due to the
L5 right area of interference ~ 19

~ R80

+ 0,2
B2

54,1 0
6 H 7 9 30 ±0,2

37±0,1
90°
L5 L4

version 20

20
(9)
Opening
±1,2

180° Right* 180° Left* 30 ±0,02 B11

Dimensions are only for
U-clamp arm, B4 8U(.)631-75-204
+ 0,020
SW22 - 0,009

left
180°point
version Area of interference
Pivot Hold-down piece must not protrude
in the interior area "R80" due to the
L5 area of interference ~

~ R80
B2

90°
8UL634-15-144 8UR634-15-144 version L5 L4
8UL634-25-144 8UR634-25-144 Opening
8UL634-45-144 8UR634-45-144

+ 0,020
SW22 - 0,009
8UL631-75-204** 8UR631-75-204**
U-Arms, left and right(Steel)
*90° left/180° right uses same clamp arm.
Pivot point
90° right/180° left uses same clamp arm.

Arm Max. Opening Max. Opening Weight B11 L4

B2 B4 B26 L5
Model No. 90º Version 180º Version (kg) ±0,1 ±0,1

8U(•)634-15-144 105º 0,52 15

8U(•)634-25-144 120º 0,54 144 64,5 105 90,5 28 25
135°
8U(•)634-45-144 0,58 45
135°
8U(•)631-75-204** 1,9 204 82 165 119 30 75
**only steel version available.

90° Left 90° Right For Size 80mm

129
U-Clamp arm, right

30 ±0,2
+0,2

30 ±0,02
76,1 0

25
6 H7 9
±
1,2
50,5 ±0,1
25 ±1,2

(9) 140 ±0,1 ~23,

180° Right* 180° Left* 7
65
U-Clamp arm, left 180° version
Area of interference
Hold-down piece
~R108

179 must not protrude

in the interior area "R108"
35 ±0,1
3,5

9 due to the area of interference.

90° Opening
8JG-170-2-01 8JG-171-2-01 version
*90° left/180° right uses same clamp arm.
J7
3,5

SW28
20 ±0,2

90° right/180° left uses same clamp arm.

Pivot point

Arm Max. Opening Max. Opening Weight

Model No. 90º Version 180º Version (kg)
8JG-17(•)-2-01** 135° 105º 3,5
**only steel version available.

Dimensions and technical information are subject to change without notice PC-PPC | 52
Lateral (Side) Arms
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions and Technical Specifications

For Size 40mm* 90° Left 90° Right

Clamp arm on the right

Ø 20 ±0,2
6 H7
Ø
7
16

0,25
(7)
20 ±0,02 90 ±0,1
Clamp arm on the left 180° Left 180° Right
180° version

Area of interference
15 hold-down pieces
which must be fixed
on the clamp arm
0

117 must not exceed

~ R7

90° version the width "16" of

the clamp arm in
22±0,1

the swivelling range

"R70" on the inner 8S401-15-117
side of the clamp arm.
Opening
45
15

SW16 H8

4
R2

Pivot point

Arm Max. Opening Max. Opening Weight

Model No. 90º Version 180º Version (kg)
8S401-15-117 135° 120º 0,5
1 clamp arm per set. Models with 2 lateral clamp arms requires 2 clamp arm sets.
*Not compatible with NAAMS Clamp Arm Shaft option 13.

For Size 50mm 90° Left 90° Right

Clamp arm on the right

30 ±0,2
Ø

Ø6
9

H7
20

10

(9) 30±0,02 105 ±0,1

Clamp arm on the left

180° version 180° Left 180° Right

Area of interference
hold-down pieces
144 which must be fixed
on the clamp arm
74 must not exceed
~R

L5 the width "20" of

75

the clamp arm in

the swivelling range
"R75" on the inner
28±0,1

side of the clamp arm

8JG-070-1-01
L5

Opening
8S501-25-144
90° version R2
8
SW19H8

Pivot point

Arm Max. Opening Max. Opening Weight

L5
Model No. 90º Version 180º Version (kg)
8JG-070-1-01 0,9 15
135° 135º
8S501-25-144 1,0 25
1 clamp arm per set. Models with 2 lateral clamp arms requires 2 clamp arm sets.

PC-PPC | 53 Dimensions and technical information are subject to change without notice
 lateral (Side) arms
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions and Technical Specifications

90° Left 90° Right Clamp arm on the right For Size 63mm

Ø9
Ø
6H 30±0,2

10
7

20
(9)
30±0,02 B11
180° Left 180° Right Clamp arm on the left

180° version
Area of interference
hold-down pieces
which must be fixed
B2 on the clamp arm
must not exceed
B4 the width "20" of
L5 the clamp arm in
the swivelling range
"R80" on the inner
8JG-080-1-01

~R
L4
side of the clamp arm

80
8S631-25-144
L5

8S631-45-144 Opening
8S631-75-204 90° version R2
8

SW22 H8
Pivot point

Arm Max. Opening Max. Opening Weight B11 L4

B2 B4 L5
Model No. 90º Version 180º Version (kg) ±0,1 ±0,1

8JG-080-1-01 0,9 15
8S631-25-144 1,0 144 74 105 28 25
135° 135º
8S631-45-144 1,1 45
8S631-75-204 1,5 204 78 165 30 75
1 clamp arm per set. Models with 2 lateral clamp arms requires 2 clamp arm sets.

90° Left 90° Right For Size 80mm

30 ±0,2
Ø9

Ø
6H
7
L10

(9)

30 ±0,02 B11

180° version

180° Left 180° Right L5 Area of interference

B2 hold-down pieces
which must be fixed
D9 on the clamp arm
L21

must not exceed

the width "L10" of
±0,1

the clamp arm in

90° version
~R

the swivelling range

35

"R108" on the inner

081

B4 side of the clamp arm

L5

L21

Opening
SW28 H8

R2

8JG-1179-1-01
8S801-45-204
Pivot point

Arm Max. Opening Max. Opening Weight B11

B2 B4 D9 L5 L10 L21 R2
Model No. 90º Version 180º Version (kg) ±0,1

8JG-1179-1-01 179 74 - 140 20 30 - 35

135° 135º 2,1
8S801-45-204 204 78 9 165 45 25 3,5 33
1 clamp arm per set. Models with 2 lateral clamp arms requires 2 clamp arm sets.

Dimensions and technical information are subject to change without notice PC-PPC | 54
Lateral (Side) Arms, NAAMS-Style
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions and Technical Specifications

For Size 50mm

50 OFFSET SERIES XXX-XXXX-X

25 OFFSET SERIES XXX-XXXX-X

75.00
50.00
R 20.00

0 OFFSET SERIES XXX-XXXX-X

15.00

25.00
15.00
A

Ø11.00 THRU TYP

Ø8.00 F7 TYP
110.00

125.00

140.00
50.00

65.00

80.00

95.00

20.00
0.00

120.00

150.00
90.00

9mm Thru Hole (6.00 H7 Dowel)

90mm [3.54”] Arm Length 120mm [4.72”] Arm Length 150mm [5.90”] Arm Length
Series Arm Style Model Series Arm Style Model Series Arm Style Model
50 Offset s • 3256 B8JG-3256-1 50 Offset s • 3257 B8JG-3257-1 50 Offset s • 3258 B8JG-3258-1
25 Offset s • 3246 B8JG-3246-1 25 Offset s • 3247 B8JG-3247-1 25 Offset s • 3248 B8JG-3248-1
0 Offset s • 3236 B8JG-3236-1 0 Offset s • 3237 B8JG-3237-1 0 Offset s • 3238 B8JG-3238-1

11mm Thru Hole (8.00 F7 Dowel)

90mm [3.54”] Arm Length 120mm [4.72”] Arm Length 150mm [5.90”] Arm Length
Series Arm Style Model Series Arm Style Model Series Arm Style Model
50 Offset s • 1226 B8JG-1226-1 50 Offset s • 1227 B8JG-1227-1 50 Offset s • 1228 B8JG-1228-1
25 Offset s • 1216 B8JG-1216-1 25 Offset s • 1217 B8JG-1217-1 25 Offset s • 1218 B8JG-1218-1
0 Offset s • 1206 B8JG-1206-1 0 Offset s • 1207 B8JG-1207-1 0 Offset s • 1208 B8JG-1208-1

s Common in North America (•) STANDARD ARM OFFERING

Maximum Opening Angle (shown in locked position)

Arm Styles
1206-1208/3236-3238­ 135° 135° 100° 100° N/A N/A
1216-1218/3246-3248 135° N/A 50° 125° N/A 30°
1226-1228/3256-3258 125° N/A 35° 135° N/A 50°

PC-PPC | 55 Dimensions and technical information are subject to change without notice
 Lateral (Side) Arms, NAAMS-Style
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions and Technical Specifications

For Size 63mm with 23 Clamp Arm Shaft Option

120 OFFSET SERIES XXX-XXXX-X

70 OFFSET SERIES XXX-XXXX-X

150.00
[5.91]
120.00
[4.72]
100.00
[3.94]
25 OFFSET SERIES XXX-XXXX-X

70.00
[2.76]
0 OFFSET SERIES XXX-XXXX-X

18.00 [0..71]
15.00 [0.59]

55.00 [2.17]
25.00 [0.98]
A
R 28.00
[1.10]

Ø9.00 [0.35] THRU TYP

Ø6.00 [0.24] H7 TYP
110.00 [4.33]

125.00 [4.92]

140.00 [5.51]

155.00 [6.10]

170.00 [6.69]

185.00 [7.28]

200.00 [7.87]

215.00 [8.46]

230.00 [9.06]
245.00 [9.65]

260.00 [10.24]
275.00 [10.83]
65.00 [2.56]
80.00 [3.15]

95.00 [3.74]

20.00
[0.79]
0.00

[10.04]

[11.22]
135.00

165.00

195.00

225.00

255.00

285.00
[5.31]

[6.50]

[7.68]

[8.86]

135mm [5.31”] Arm Length 165mm [6.50”] Arm Length 195mm [7.68”] Arm Length
Series Arm Style Model Series Arm Style Model Series Arm Style Model
120 Offset s 1543 B8JG-1543-1 120 Offset s 1544 B8JG-1544-1 120 Offset s 1545 B8JG-1545-1
70 Offset s 1531 B8JG-1531-1 70 Offset s 1532 B8JG-1532-1 70 Offset s 1533 B8JG-1533-1
25 Offset s 1519 B8JG-1519-1 25 Offset s 1520 B8JG-1520-1 25 Offset s 1521 B8JG-1521-1
0 Offset s 1507 B8JG-1507-1 0 Offset s 1508 B8JG-1508-1 0 Offset
STANDARD s 1509
BLANK ARM OFFERING B8JG-1509-1
OFFSET ARM STYLE PART NUMBER
(•) STANDARD ARM OFFERING 20 •018
225mm [8.86”] Arm Length 255mm [10.04”] Arm Length 285mm 8JG-1018-1
[11.22”] Arm Length
Series Arm StyleARM STYLEModel
OFFSET PART NUMBER Series Arm Style Model OFFSET Series ArmNUMBER
ARM STYLE PART Style Model
120 Offset s120
1546
70
•043 8JG-1043-1
B8JG-1546-1
•031 8JG-1031-1 120 Offset s 1547 B8JG-1547-1 120
70
120 048
Offset
036
8JG-1048-1
s 1548
8JG-1036-1
B8JG-1548-1
70 Offset 25
s 1534 •019 8JG-1019-1
B8JG-1534-1 70 Offset s 1535 B8JG-1535-1 25 70 Offset
024 s 1536
8JG-1024-1 B8JG-1536-1
0 •007 8JG-1007-1 0 012 8JG-1012-1
25 Offset s 1522 B8JG-1522-1 25 Offset s 1523 B8JG-1523-1 25 Offset s 1524 B8JG-1524-1
OFFSET ARM STYLE PART NUMBER OFFSET ARM STYLE PART NUMBER
0 Offset 1510
s120 B8JG-1510-1
044 8JG-1044-1 0 Offset s 1511 B8JG-1511-1 120
0 Offset
047
s 1512
8JG-1047-1
B8JG-1512-1
70 •032 8JG-1032-1 70 •035 8JG-1035-1
25 •020 8JG-1020-1 25 023 8JG-1023-1
s Common in North0 America
•008 8JG-1008-1 0 011 8JG-1011-1

OFFSET ARM STYLE PART NUMBER OFFSET ARM STYLE PART NUMBER
120 045 8JG-1045-1 120 046 8JG-1046-1
70 •033 8JG-1033-1 70 •034 8JG-1034-1
25 021 Maximum
8JG-1021-1 Opening Angle (shown in locked position)
25 022 8JG-1022-1
0 •009 8JG-1009-1 0 010 8JG-1010-1

Arm Styles
1510-1512/1507-1509 135° 135° 100° 100° N/A N/A
1522-1524/1519-1521 135° N/A 50° 130° N/A 40°
1534-1536/1531-1533 115° N/A 25° 135° N/A 75°
1546-1548/1543-1545 110° N/A 20° 135° N/A 85°

Dimensions and technical information are subject to change without notice PC-PPC | 56
Lateral (Side) Arms, NAAMS-Style
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions and Technical Specifications

For Size 63mm with D0 Clamp Arm Shaft Option

120 OFFSET SERIES XXX-XXXX-X

70 OFFSET SERIES XXX-XXXX-X

150.00
[5.91]
120.00
[4.72]
100.00
[3.94]
25 OFFSET SERIES XXX-XXXX-X

70.00
[2.76]
0 OFFSET SERIES XXX-XXXX-X

18.00 [0..71]
15.00 [0.59]

55.00 [2.17]
25.00 [0.98]
A
R 28.00
[1.10]

Ø11.00 [0.43] THRU TYP

Ø8.00 [0.31] F7 TYP
110.00 [4.33]

125.00 [4.92]

140.00 [5.51]

155.00 [6.10]
170.00 [6.69]

185.00 [7.28]

200.00 [7.87]

215.00 [8.46]

230.00 [9.06]
245.00 [9.65]

260.00 [10.24]
275.00 [10.83]
65.00 [2.56]
80.00 [3.15]

95.00 [3.74]

25.00
[0.98]
0.00

[10.04]

[11.22]
135.00

165.00

195.00

225.00

255.00

285.00
[5.31]

[6.50]

[7.68]

[8.86]

135mm [5.31”] Arm Length 165mm [6.50”] Arm Length 195mm [7.68”] Arm Length
Series Arm Style Model Series Arm Style Model Series Arm Style Model
120 Offset s • 1043 B8JG-1043-1 120 Offset s 1044 B8JG-1044-1 120 Offset s 1045 B8JG-1045-1
STANDARD BLANK ARM OFFERING
70 Offset s • 1031 B8JG-1031-1 70 Offset s • 1032 B8JG-1032-1 70 Offset s • 1033 B8JG-1033-1
OFFSET ARM STYLE PART NUMBER
25 Offset s • 1019 (•) B8JG-1019-1
STANDARD ARM OFFERING 25 Offset s • 1020 B8JG-1020-1 20 25 Offset
•018 s 1021
8JG-1018-1 B8JG-1021-1
0 Offset s • 1007 OFFSETB8JG-1007-1
ARM STYLE PART NUMBER0 Offset s • 1008 B8JG-1008-1 OFFSET 0ARM
Offset • 1009
s NUMBER
STYLE PART B8JG-1009-1
120 •043 8JG-1043-1 120 048 8JG-1048-1
70 •031 8JG-1031-1 70 036 8JG-1036-1
225mm [8.86”] Arm
25
0
Length
•019
•007
255mm [10.04”] Arm Length
8JG-1019-1
8JG-1007-1
25
0
285mm
024
012
[11.22”] Arm Length
8JG-1024-1
8JG-1012-1
Series Model
Arm Style OFFSET ARM Series Arm Style Model Series Arm Style Model
STYLE PART NUMBER OFFSET ARM STYLE PART NUMBER
120 Offset s 1046 120 B8JG-1046-1
044 120 Offset
8JG-1044-1 s 1047 B8JG-1047-1 120120 Offset
047 s 1048
8JG-1047-1 B8JG-1048-1
70 •032 8JG-1032-1 70 •035 8JG-1035-1
70 Offset s • 1034 25 B8JG-1034-1
•020 70 Offset
8JG-1020-1 s • 1035 B8JG-1035-1 25 70 Offset
023 s 1036
8JG-1023-1 B8JG-1036-1
0 •008 8JG-1008-1 0 011 8JG-1011-1
25 Offset s 1022 B8JG-1022-1 25 Offset s 1023 B8JG-1023-1 25 Offset s 1024 B8JG-1024-1
OFFSET ARM STYLE PART NUMBER OFFSET ARM STYLE PART NUMBER
0 Offset s 1010 120 B8JG-1010-1
045 8JG-1045-1 0 Offset s 1011 B8JG-1011-1 120 0 Offset
046 s 1012
8JG-1046-1 B8JG-1012-1
70 •033 8JG-1033-1 70 •034 8JG-1034-1
25 021 8JG-1021-1 25 022 8JG-1022-1
s Common in North America
0 (•)
•009 STANDARD
8JG-1009-1 ARM OFFERING  NON-STANDARD0ARM OFFERING
010 (extended leadtimes apply)
8JG-1010-1

Maximum Opening Angle (shown in locked position)

Arm Styles
1010-1012/1007-1009 135° 135° 100° 100° N/A N/A
1022-1024/1019-1021 135° N/A 50° 130° N/A 40°
1034-1036/1031-1033 115° N/A 25° 135° N/A 75°
1046-1048/1043-1045 110° N/A 20° 135° N/A 85°

PC-PPC | 57 Dimensions and technical information are subject to change without notice
 Lateral (Side) Arms, NAAMS-Style
Enclosed Pneumatic Power Clamps | Heavy-Duty Modular | Dimensions and Technical Specifications

For Size 80mm

120 OFFSET

70 OFFSET

155.00
R35.00

120.00
105.00
25 OFFSET

0 OFFSET

20.00

60.00

70.00
25.00
24.00
A

Ø11.00 THRU TYP

Ø8.00 F7 TYP
100.00
115.00
130.00
145.00
160.00
175.00
190.00
205.00
220.00
235.00
250.00
265.00
280.00
295.00
310.00
325.00
340.00
355.00
370.00
385.00
85.00
0

32.00
185.00

365.00
155.00

215.00

245.00

275.00

305.00

335.00

395.00
(•) STANDARD ARM OFFERING

155mm [4.53”] Arm Length 185mm [7.28”] Arm Length 215mm [8.46”] Arm Length
Series Arm Style Model Series Arm Style Model Series Arm Style Model
120 Offset s 1170 B8JG-1170-1 120 Offset s 1171 B8JG-1171-1 120 Offset s 1172 B8JG-1172-1
70 Offset s • 1150 B8JG-1150-1 70 Offset s 1151 B8JG-1151-1 70 Offset s 1152 B8JG-1152-1
25 Offset s 1130 B8JG-1130-1 25 Offset s 1131 B8JG-1131-1 25 Offset s 1132 B8JG-1132-1
0 Offset s 1110 B8JG-1110-1 0 Offset s 1111 B8JG-1111-1 0 Offset s • 1112 B8JG-1112-1

245mm [9.65”] Arm Length 275mm [10.83”] Arm Length 305mm [12.00”] Arm Length
Series Arm Style Model Series Arm Style Model Series Arm Style Model
120 Offset s 1173 B8JG-1173-1 120 Offset s 1174 B8JG-1174-1 120 Offset s 1175 B8JG-1175-1
70 Offset s 1153 B8JG-1153-1 70 Offset s 1154 B8JG-1154-1 70 Offset s • 1155 B8JG-1155-1
25 Offset s 1133 B8JG-1133-1 25 Offset s • 1134 B8JG-1134-1 25 Offset s 1135 B8JG-1135-1
0 Offset s 1113 B8JG-1113-1 0 Offset s 1114 B8JG-1114-1 0 Offset s 1115 B8JG-1115-1

335mm [13.19”] Arm Length 365mm [14.37”] Arm Length 395mm [15.55”] Arm Length
Series Arm Style Model Series Arm Style Model Series Arm Style Model
120 Offset s 1176 B8JG-1176-1 120 Offset s 1177 B8JG-1177-1 120 Offset s 1178 B8JG-1178-1
70 Offset s 1156 B8JG-1156-1 70 Offset s 1157 B8JG-1157-1 70 Offset s • 1158 B8JG-1158-1
25 Offset s 1136 B8JG-1136-1 25 Offset s 1137 B8JG-1137-1 25 Offset s 1138 B8JG-1138-1
0 Offset s 1116 B8JG-1116-1 0 Offset s 1117 B8JG-1117-1 0 Offset s • 1118 B­8JG-1118-1

s Common in North America (•) STANDARD ARM OFFERING  NON-STANDARD ARM OFFERING (extended leadtimes apply)

Maximum Opening Angle (shown in locked position)

Arm Styles
1110 - 1118 135° 135° 100° 100° N/A N/A
1130 - 1138 135° N/A 60° 120° N/A 30°
1150 - 1158 125° N/A 35° 135° N/A 55°
1170 - 1178 115° N/A 25° 135° N/A 80°

Dimensions and technical information are subject to change without notice PC-PPC | 58