ae |

~ ON-SITE
mee)To BS 7671 : 2001 (2004)
mM eras eee ny
irae CUCU LC ae
No1:2002
and No 2: rt Aes
Ms
ae = -
ig -*

= rd
3 5
a (Pe
eae,
2r ay wy
= 7 Peas =,
 re en mn

|(ANTIFpeey Prerereer PNP any

}1 TALE LELG t et i . BD «=e Doy
DEP AL

|
i
IAMwT!
HAR Lor
os
Wak,
3 ; =
Weeyeurviil.
at LAID

“To BS 7671 : 2001 (2004)

16th Edition Wiring Regulations
_...ncluding Amendments
No 1 : 2002
and No 2 : 2004

WWI
Published by: The IEE, LONDON, UK

©2004 The Institution of Electrical Engineers

Printed February 1992

Reprinted May 1993, with amendments
Reprinted July 1993, with amendment (Appendix 9)
Reprinted February 1994, with amendments
Revised February 1995 to incorporate Amendment No 1 to BS 7671
Revised June 1996, new cover only
Revised June 1998 to incorporate Amendment No 2 to BS 7671
Revised Feb 2002 to incorporate BS 7671 : 2001, inc Amd No 1 : 2002
Reprinted July 2003, new cover only
Revised April 2004 to incorporate BS 7671 : 2001, inc Amd No 2 : 2004

This publication is copyright under the Berne Convention 2003 and the Universal
Copyright Convention. All rights reserved. Apart from any fair dealing for the purposes
of research or private study, or criticism or review, as permitted under the Copyright,
Designs and Patents Act, 1988, this publication may be reproduced, stored or
transmitted, in any form or by any means, only with the prior permission in writing of
the publishers, or in the case of reprographic reproduction in accordance with the terms
of licences issued by the Copyright Licensing Agency. Inquiries concerning reproduction
outside those terms should be sent to the publishers at the undermentioned address:
The IEE, Michael Faraday House, Six Hills Way, STEVENAGE, SG1 2AY, United Kingdom

Copies may be obtained from The IEE:

The IEE
P.O. Box 96
Stevenage
SG1 2SD, UK
Tel: +44 (0)1438 767 328
Email: [email protected]
http:/Awww.iee.org/Publish/Books/WireAssoc/

While the publisher and contributors believe that the information and
guidance given in this work is correct, all parties must rely upon their
own skill and judgement when making use of it. Neither the publisher
nor any contributor assume any liability to anyone for any loss or
damage caused by any error or omission in the work, whether such
error or omission is the result of negligence or any other cause. Where
reference is made to legislation it is not to be considered as legal
advice. Any and all such liability is disclaimed.

ISBN 0 86341 3749

2
 CONTENTS
Page

PREFACE

FOREWORD

SECTION 1. INTRODUCTION 11
Scope 11
i Basic Information Required 13

SECTION 2. THE SERVICE POSITION 14

2.1 General Layout of Equipment 14
22 Function of Components: 14

SECTION 3. PROTECTION wz,

31 Types of Protective Device(s) LZ,
3.2 Overload Protection 17
33 Fault Current Protection 17
3.4 Protection Against Electric Shock ty
3D Disconnection Times 19
3.6 Residual Current Devices (RCD) 19

SECTION 4. BONDING AND EARTHING 24

4.1 Main Equipotential Bonding of Metal
Services (Figs 4a, 4b, 4c) 24
4.2 Main Earthing and Main Equipotential
Bonding Conductor Cross-sectional Areas 24
4.3 Main Equipotential Bonding - Plastic Services 25
4.4 Earthing . as
4.5 Supplementary Equipotential Bonding in
Locations of Increased Shock Risk - Metal
Pipework 25
4.6 Supplementary Bonding in other Locations -
Metal Pipework 26
4.7 Supplementary Bonding of Plastic Pipe
Installations 26
4.8 Earth Electrode (Fig 4c) 32
4.9 Types of Earth Electrode SZ
4.10 Typical Earthing Arrangements 33
SECTION 5. ISOLATION AND SWITCHING 34
Dal Isolation 34
a2 Functional Switching 35
Sp5) Switching Off for Mechanical Maintenance 35
5.4 Emergency Switching 35
SECTION 6. LABELLING 37
6.1 Labels to be Provided 37
SECTION 7. FINAL CIRCUITS 40
7.1 Final Circuits 40
Tid Using the Tabulated Final Circuits 41
23 Installation Considerations 52
74 Smoke Alarms and Emergency Lighting 56
SECTION 8. SPECIAL LOCATIONS GIVING RISE TO
INCREASED RISK OF ELECTRIC SHOCK 58
8.1 Locations Containing a Bath or Shower 58
8.2 Shower Cubicles in a Room used for Other
Purposes 60
8.3 Temporary and Garden Buildings, Domestic
Garages, Buildings of Lightweight
Construction etc 60
8.4 Earthing requirements of Equipment
having High Protective Conductor Current 60
SECTION 9. INSPECTION AND TESTING 62
oA Inspection and Testing 62
9:2 Inspection 62
os Testing 65
SECTION 10. GUIDANCE NOTES ON INITIAL TESTING OF
INSTALLATIONS 66
10.1 Safety and equipment 66
10.2 Sequence of Tests 66
10.3 Test Procedures 67
SECTION 11. OPERATION OF RESIDUAL CURRENT
OPERATED DEVICES(RCDs) AND
RESIDUAL CURRENT BREAKERS WITH
OVERCURRENT PROTECTION (RCBOs) 81
11.1 General Test Procedure
11.2 General purpose RCDs to BS 4293 81
11.3 General purpose RCCBs to BS EN 61008 or
RCBOs to BS EN 61009 81
11.4 RCD protected socket-outlets to BS 7288 81
11.5 Additional Requirement for Supplementary
Protection 82
11.6 Integral Test Device 82
 Page

APPENDICES

Maximum demand and diversity 84

2 Maximum permissible measured earth

fault loop impedance 88

3 Notes on the selection of types of

cable and flexible cord for particular
uses and external influences 94

4 Notes on methods of support for

cables, conductors and wiring systems 100

5 Cable capacities of conduit and

trunking 109

6 Current-carrying capacities and

voltage drop for copper conductors 115

7 Certification and reporting Za

8 Standard circuit arrangement for

household and similar installations 150

9 Resistance of copper and aluminium

conductors 157

10 Protective conductor sizing 161

11. Identification of conductors 164

INDEXES

(i) The installation 170

(ii) Bonding and earthing 173

(iii) Special locations and RCDs 174

(iv) Inspection and testing 176

(vy) Alphabetical 178

 Co-operating Organisations
The IEE acknowledges the contribution made by the following organisations
in the preparation of this guide.
Association of Manufacturers of Domestic Electrical Appliances
S A MacConnacher BSc CEng MIEE
BEAMA Installation Ltd
Eur Ing MH Mullins BA CEng FIEE FIIE
British Cables Association
C K Reed | Eng MIIE
British Electrotechnical & Allied Manufacturers Association Ltd
R F B Lewington MIEE
British Electrotechnical Approvals Board
P D Stokes MA CEng MRAeS
British Standards Institution
M R Danvers
City & Guilds of London Institute
H R Lovegrove IEng FIIE
Electrical Contractors’ Association
D Locke IEng MIIE ACIBSE
Electrical Contractors’ Association of Scotland t/a SELECT
D Millar IEng MIIE MILE
Electricity Association Limited
D J Start BSc CEng MIEE
ERA Technology Ltd
M W Coates BEng
Federation of the Electronics Industry
F W Pearson CEng MIIE
The GAMBICA Association Ltd
K A Morriss BSc CEng MIEE
Health & Safety Executive
Eur Ing J A McLean BSc CEng FIEE FIOSH
Institution of Incorporated Engineers
P Tootill IEng MIIE
Lighting Association
K R Kearney IEng MIIE
National Inspection Council for Electrical Installation Contracting
Safety Assessment Federation Limited
J Gorman BSc (Hons) CEng MIEE
Society of Electrical and Mechanical Engineers serving Local Government
C J Tanswell CEng MIEE MCIBSE

Editor P RL Cook CEng FIEE MCIBSE

 PREFACE
The On-Site Guide is one of a number of publications prepared by
the IEE to simplify some aspects of BS 7671 : 2001 (2004) Requirements
for Electrical Installations (IEE Wiring Regulations Sixteenth Edition).
BS 7671 is a joint publication of the British Standards Institution and
the Institution of Electrical Engineers.

The scope generally follows that of BS 7671. It includes material not

included in BS 7671, provides background to the intentions of BS 7671,
and gives other sources of information.

However, this guide does not ensure compliance with BS 7671. It is a

simple guide to the requirements of BS 7671, and electricians should
always consult BS 7671 to satisfy themselves of compliance.

It is expected that persons carrying out work in accordance with this

guide will be competent to do so.
Electrical installations in the United Kingdom which comply with the
IEE Wiring Regulations, BS 7671, should also comply with the
Statutory Regulations such as the Electricity at Work Regulations 110-01-01
1989. It cannot be guaranteed that BS 7671 complies with all
relevant Regulations and it is stressed that it is essential to establish
what statutory and other Regulations apply and to_ install
accordingly. For example, an installation in Licensed Premises may App 2(vi)
have requirements different from or additional to BS 7671 and these
will take precedence over BS 7671.
 FOREWORD
This Guide is concerned with limited application of BS 7671 in
accordance with para 1.1 Scope. Part|

BS 7671 and the On-Site Guide are not design guides. It is essential to
prepare a schedule of the work to be done prior to commencement
or alteration of an electrical installation and to provide all necessary
information and operational manuals of any equipment supplied to
the user on completion.

Any specification should set out the detailed design and provide
sufficient information to enable competent persons to carry out the
installation and to commission it. The specification must include a
description of how the system is to operate and all of the design and
operational parameters.

The specification must provide for all the commissioning procedures

that will be required and for the production of any operational
manual.

It must be noted that it is a matter of contract as to which person

or organisation is responsible for the production of the parts of the
design, specification and any operational manual.

The persons or organisations who may be concerned ‘in the

preparation of the specification include:

The Designer(s)
The Installer(s)
The Electricity Distributor
The Installation Owner and/or User
The Architect
The Fire Prevention Officer
The Planning Supervisor
All Regulatory Authorities
Any Licensing Authority
The Health and Safety Executive
In producing the specification advice should be sought from the
installation owner and/or user as to the intended use. Often, such
as in a speculative building, the detailed intended use is unknown. In
those circumstances the specification and/or the operational manual
must set out the basis of use for which the installation is suitable.

Precise details of each item of equipment should be obtained from

the manufacturer and/or supplier and compliance with appropriate
standards confirmed.

The operational manual must include a description of how the

system as installed is to operate and all commissioning records. The
manual should also include manufacturers’ technical data for all
items of switchgear, luminaires, accessories, etc and any special
instructions that may be needed. The Health and Safety at Work etc
Act 1974 Section 6 and the Construction (Design and Management)
Regulations 1994 are concerned with the provision of information.
Guidance on the preparation of technical manuals is given in BS 4884
(Specification for technical manuals) and BS 4949 (Recommendations
for the presentation of technical information about products and
services in the construction industry). The size and complexity of the
installation will dictate the nature and extent of the manual.

10
 ON-SITE GUIDE
SECTION 1. INTRODUCTION

pat Scope

This Guide is for electricians (skilled persons). It covers the

following installations:

(a) domestic installations generally, including off-peak

supplies, and supplies to associated garages,
out-buildings and the like

(b) industrial and commercial single- and three-phase

installations where the distribution board(s) or
consumer unit is located at or near the distributor's
cut-out.

Note: Special Installations or Locations (Part 6 of BS 7671) are generally Part 6

excluded from this Guide. Advice is given on installations in locations
containing a bath or shower (8.1), temporary and garden buildings etc (8.3)
and personal computer circuits in office locations (8.4).

This Guide is restricted to installations : 313-01-01

(i) at a supply frequency of 50 Hertz

(ii) at a nominal single-phase voltage of 230 V a.c.

single-phase and 230/400 V a.c. three-phase

(iii) | fed through a distributor's cut-out having a fuse or

fuses to BS 1361 Type II or through fuses to BS 88-2 or
BS 88-6

(iv) | with a maximum value of the earth fault loop

impedance outside the consumer's installation as
follows:
Earth return via sheath (TN-S system): 0.8 ohm
Earth return via combined neutral and earth conductor
(TN-C-S system): 0.35 ohm
TT systems: 21 ohms excluding consumer's earth
electrode

11
Sec 1
 This Guide contains information which may be required in
general installation work, e.g. conduit and trunking capacities,
bending radii of cables.

This Guide introduces the use of conventional circuits, which

are discussed in Section 7.

Because of simplification this Guide may not give the most

economical result.

This Guide is not a replacement for BS 7671, which should always

be consulted. Defined terms according to Part 2 of BS 7671 are
used in this Guide.

In conformance with the definitions of BS 7671, throughout

this Guide the term ‘live part’ is used to refer to a conductor or
conductive part intended to be energised in normal use,
including a neutral conductor. For convenience in use, and in
accordance with current UK manufacturing practice, the Part2
terminals of electrical equipment shown in Figs 10.1 to 10.5 figs
3to 7
have been identified by the letters L, N and E.

Further information is available in the series of Guidance Notes

published by the Institution.

For new domestic installations and major refurbishments

account should be taken of the recommendations in Approved
Document B, issued as guidance on the Building Regulations
1991. Part B1, Section 1 advises that, if dwellings are not
protected by an automatic fire detection and alarm system to
Part 6 of BS 5839, a suitable number of mains operated
self-contained smoke alarms to BS 5446 be installed.

In Scotland the Building Standards (Scotland) Regulations 1990

apply and installations must comply with The Scottish Office
Technical Standards .

12
Sec 1
 Part 3
{2 Basic Information Required

Before starting work on an installation that requires a new

supply, the electrician should obtain the following information
from the distributor:
312-02-01
(i) the number of phases to be provided
313-01-01((iii)
(ii) the distributor’s requirement for cross-sectional area
and length of meter tails
313-01-01(iii)
(iii) | the maximum prospective fault current (pfc) at the
supply terminals
313-01-01('v)
(iv) | the maximum earth loop impedance (Ze) of the earth
fault path outside the consumer's installation
313-01-01(vi)
(v) the type and rating of the distributor's fusible cut-out
or protective device

(vi). the distributor’s requirement regarding the size of main 947-0201

equipotential bonding
312-03-01
(vii) the earthing arrangement and type of system

(viii) the arrangements for the incoming cable and metering. 3130101)

For existing installations, electricians should satisfy themselves

as to the suitability of the supply including the earthing
arrangement.

13
Sec 1
 SECTION 2. THE SERVICE POSITION

ail General Layout of Equipment

The general layout of the equipment at the service position is

shown in Figs 2a and 2b.

2.2. Function of Components:

(i) Distributor’s Cut-out

This will be sealed to prevent the fuse being withdrawn 3130101)

by unauthorised persons. When the meter tails and
consumer unit are installed in accordance with the
requirements of the distributor the cut-out may be
assumed to provide fault current protection up to the
consumer's main switch.

(ii) Supplier’s Meter

This will be sealed by the supplier to prevent

interference by unauthorised persons.

(iii) | Meter Tails

These are part of the consumer’s installation. They 473-02-04(v)

should be insulated and sheathed or insulated and 521-07-03
enclosed in conduit or trunking.

Polarity should be indicated by the colour of the 514-06

insulation and the minimum cable size should be
25 mm<2. The distributor may specify the maximum length
and the minimum cross-sectional area (see 1.2(ii)).

Where the meter tails are protected against fault current 473-02-04(v)
by the distributor’s cut-out the method of installation,
maximum length and minimum cross-sectional area
must comply with the requirements of the distributor.

14
Sec 2
Fig 2a: Layout when the supplier does not provide a main switch
Note: Earthing arrangements have been omitted for clarity. Tails between the
meter and the consumer’s installation are provided by the consumer

meter consumer's
installation
ee ne supplier’s
ine:
terminals

consumer's meter tails

distributor's
cut-out

Fig 2b: Layout when the supplier does provide a main switch
Note: Earthing arrangements have been omitted for clarity. Tails between any
main switch provided by the supplier and the consumer's installation are
provided by the consumer

consumer’s
installation

consumer's
tails

ee supplier's
main switch terminals
distributor's
cut-out

15
Sec 2
 (iv) Supplier’s Switch

Some suppliers may provide and install a suitable switch

between the meter and the consumer unit. This permits 476-01-01
the supply to the installation to be interrupted without
withdrawing the distributor's fuse in the cut-out.

(v) Consumer’s Controlgear

A consumer unit is for use on single-phase installations. Part 2

It contains a double-pole main switch and fuses or
circuit-breakers (cbs) and perhaps residual current
devices (RCDs) or residual current breakers with integral
overcurrent protection (RCBOs) for the protection of
each final circuit. Alternatively, a separate main switch
and distribution board may be provided.

16
Sec 2
 SECTION 3. PROTECTION

3.1. Types of Protective Device(s)

The consumer unit (or distribution board) contains devices for ch 43

the protection of the final circuits against:

(i) overload 433

(ii) short-circuit 434
(iii) earth fault. 434

Functions (i) and (ii) are carried out usually by one device, a fuse
or circuit-breaker.

Function (iii) may be carried out by the fuse or circuit-breaker 413-02-04

provided for functions (i) and (ii), or by an RCD.

An RCBO being a combined circuit-breaker and RCD will carry

out functions (i), (ii) and (iii).
3.2 Overload Protection

Overload protection is given by the following devices:

Fuses to BS 88-2.1 or BS 88-6; BS 1361 and BS 3036; App 3

miniature circuit-breakers to BS 3871-1 Types 1, 2 and 3;
circuit-breakers to BS EN 60898 types B, C and D; and
residual current circuit-breakers with integral
overcurrent protection (RCBOs) to BS EN 61009-1.

3.3 Fault Current Protection

When a consumer unit to BS EN 60439-3 or BS 5486 : Part 13, 473-02-04

or a fuseboard having fuselinks to BS 88-2.1 or BS 88-6 or BS 1361
is used, then fault current protection will be given by the
overload protective device.

For other protective devices the breaking capacity must be

adequate for the prospective fault current at that point.

3.4 Protection Against Electric Shock

(i) Direct Contact 412

Electrical insulation and enclosures and barriers give 412-01-01

protection against direct contact. Non-sheathed
insulated conductors must be protected by conduit or 521-07-03

17
Sec 3
 trunking or be within a suitable enclosure. A 30 mA
RCD may be provided to give supplementary protection 412-06
against direct contact, but must not be relied upon for
primary protection.

(ii) Indirect Contact 413

Protection against indirect contact is given by limiting

to safe values the magnitude and duration of voltages
that may appear under earth fault conditions between
simultaneously accessible exposed-conductive-parts of
equipment, and between them and_ extraneous-
conductive-parts or earth. This may be effected by the:

(a) co-ordination of protective devices and circuit 413-02-04

impedances, or

(b) use of RCDs to limit the disconnection time, or 413-02-07

(c) | use of Class Il equipment or equivalent insulation. 413-03

(iii) SELV and PELV

SELV 411-02
Separated extra-low voltage (SELV) systems

(a) aresupplied from isolated safety sources such as 4111-02-02

a safety isolating transformer to BS 3535

(b) have no live part connected to earth or the 411-02-05

protective conductor of another system

(c) are enclosed in an insulating sheath additional to 411-02-06

their basic insulation

(d) have no exposed-conductive-parts connected to —_411-02-07

earth, to exposed-conductive-parts or protective
conductors of other systems or to extraneous-
conductive-parts.

PELV. 471-14-01
Protective extra-low (PELV) systems must meet all the 471-14-02
requirements for SELV, except that the circuits are not
electrically separated from earth.

18
Sec 3
 For SELV and PELV systems protection against direct 411-02-09
contact need not be provided if voltages do not exceed 471-14-02
the following:

Dry areas 25 V a.c. or 60 V d.c. 25 Va.c. or 60 V d.c. 411-02-09

Bathrooms, swimming Protection required at Protection required at 601-03-02

pools, saunas all voltages all voltages 602-03-01
603-03-01

Other areas 12 Va.c. or 30

V d.c. 6Va.c. or 15
V d.c. 471-01-01
471-14-02

Sao Disconnection Times

3.5.1. Conventional Circuits

For the conventional circuits given in Section 7, the correct

disconnection time in seconds (0.4 s or 5s) is obtained by using
the protective devices and related maximum circuit lengths in
Table 7.1.

3.5.2 Special Circuits

A disconnection time of not more than 0.4 s is required for final

circuits supplying:
(i) portable equipment intended to be moved by hand 413-02-09
while in use
(ii) hand-held metal-cased equipment requiring an earth, —413-02-09
and supplied directly or through a socket-outl et
(iii) fixed equipment outside the equipotential zone with — 4711-08-03
accessible exposed-conductive-parts

3.6 Residual Current Devices (RCD)

Note: Residual current device (RCD) is a device type that includes residual current
circuit-breakers (RCCBs) and residual current circuit-breakers with integral
overcurrent protection (RCBOs).

3.6.1 Protection by an RCD

There are a number of instances where an installation is

required to incorporate one or more RCDs (RCCB or RCBO).
These instances include:

19
Sec 3
 (i) where the earth fault loop impedance is too high to 413-02-19
provide the required disconnection time e.g. where the
distributor does not provide an earth - TT systems
(ii) on socket-outlet circuits in TT systems 471-08-06

(iii) | on all socket-outlets that may reasonably be expected 471-16-01

to supply portable equipment used outdoors
(iv) circuits supplying portable equipment for use outdoors 471-16-02
by means of a flexible cable.
(v) on socket-outlets in a room, other than a bathroom or 601-08-02
shower room, containing a shower cubical.

3.6.2 Applications of RCDs

Installations are required to be divided into circuits to avoid 314-01-01
danger and minimise inconvenience in the event of a fault and
to take account of hazards that might arise from the failure of 314-01-02
a single circuit, e.g. a lighting circuit.

30 mA RCDs installed to provide protection to socket-outlets

likely to feed portable equipment outdoors should protect only
those sockets, see Fig 3b.

Where an RCD is fitted only because the earth loop impedance

is too high for shock protection to be provided by an
overcurrent device, for example in a TT system, the rated
residual operating current should not be less than 100 mA.
If two RCDs are installed they should preferably control
separate circuits, see Fig 3a(i), or a time delay 100 mA or
greater RCD (S type) should be installed, see Fig 3a(ii).

The use of RCBOs, see Fig 3a(iii), will minimise inconvenience

in the event of a fault.

The enclosures of RCDs or consumer units incorporating RCDs

in TT installations should be of an all-insulated or Class II
construction. Otherwise, additional precautions recommended
by the manufacturer need to be taken to prevent faults to
earth on the supply side of the RCD.

20
Sec 3
Fig 3a: Installing RCDs in a TT installation

i) consumer unit with separate isolator Pe

consumer unit with insulated enclosure or
additional protection to meter and isolator tails

note 1

labelled
“main
switch”

ii) consumer unit using time delayed RCD as main switch

consumer unit with insulated enclosure or
additional protection to meter tails

note 1

labelled
“main
switch’

note 1 circuits to lights, cooker, water heater, smoke alarms

2 circuits to portable equipment outdoors and socket-outlets that may reasonably supply
portable equipment outdoors (ground floor socket-outlets)
3 time delay (S-type) double-pole RCD to BS EN 61008. This RCD must be clearly identified
(labelled) as the main switch for the installation

21
Sec 3
Fig 3a cont'd: Installing RCDs in a TT installation

iii) consumer unit with RCBOs

consumer unit with insulated enclosure or
additional protection to meter tails

lAn 2 100 mA
note 4

labelled
“main
switch’

note 4 Circuits to lights, cooker, water heating, smoke alarms

5 Circuits to portable equipment outdoors and socket-outlets that may reasonably supply
equipment outdoors, and certain equipment in bathrooms - see Table 8.1

3.6.3 Applications of residual current circuit-breakers with

overload current protection (RCBOs)

In TN systems it is preferable for reliable operation for indirect 413-02-04

shock protection to be provided by overcurrent devices,
including RCBOs operating as overcurrent devices; that is, with
loop impedances complying with Table 2D of Appendix 2. RCBOs
are then providing indirect shock protection as overcurrent
devices and supplementary protection against direct contact as 471-16
residual current circuit-breakers (RCCBs).

When the designer intends that indirect shock protection is to 413-02-16

be provided by a residual current circuit-breaker (RCCB) or the
residual current element of an RCBO, loop impedances are as
for an RCD, that is appropriate to the rated residual operating
current (Z; < 50 V/ Ian), and not more than 200 ohms.

22
Sec 3
Fig 3b: Installing RCDs in a TN-S or TN-C-S installation

note 1 The 30 mA RCD and associated cbs may be replaced by residual current breakers with
overcurrent protection (RCBOs) on the main switch busbar rail
2 Circuits to lights, cooker, water heating, smoke alarms
3 Circuits to portable equipment outdoors and socket-outlets that may reasonably supply
equipment outdoors

23
Sec 3
 SECTION 4. BONDING AND EARTHING

4.1. Main Equipotential Bonding of Metal Services (Figs 4a,

4b, 4c)
Main equipotential bonding conductors are required to 413-02-02
connect the following metallic parts to the main earthing
terminal, where they are extraneous-conductive-parts:
(i) metal water service pipes
(ii) metal gas installation pipes
(iii) | other metal service pipes (including oil and gas supply
pipes) and ducting
(iv) | metal central heating and air conditioning systems
(v) exposed metallic structural parts of the building
(vi) lightning protection systems.

4.2. Main Earthing and Main Equipotential Bonding

Conductor Cross-Sectional Areas

The minimum cross-sectional area (csa) of the main equipotential 547-02-01

bonding conductor is half that of the main earthing
conductor. For 100 A TN installations, the main earthing
conductor csa needs to be 16 mm? and that of the main
bonding conductors 10 mm? where the size of the supply Table 54H
neutral conductor is not more than 35 mm2. However, local
public electricity distribution network conditions may require
larger conductors. For other conditions see Table 10A of
Appendix 10. For TT installations see Fig 4c.

Note that:
(i) only copper conductors should be used; copper covered 542-03-03
aluminium conductors or aluminium conductors or
structural steel can only be used if special precautions
outside the scope of this Guide are taken
(ii) bonding connections to incoming metal services should 547-02-02
be as near as possible to the point of entry of the
services to the premises, but on the consumer's side of
any insulating section
(iii) the connection to the gas, water, oil, etc service should 5547-02-02
be within 600 mm of the service meter, or at the point
of entry to the building if the service meter is external,

24
Sec 4
 and must be on the consumer’s side before any branch
pipework and after any insulating section in the service.
The connection must be made to hard pipe, not to soft
or flexible meter connections
(iv) | the connection must be made using clamps (to BS 951) —542-03-03
which will not be subject to corrosion at the point of
contact
(v) if incoming gas and water services are of plastic, main
bonding connections are to be made to metal
installation pipes only.

4.3 Main Equipotential Bonding - Plastic Services

There is no requirement to main bond an incoming service

where both the incoming service pipe and the pipework
within the installation are both of plastic. Where there is a
plastic incoming service and a metal installation within the
premises, main bonding must be carried out, the bonding
being applied on the customer's side of any meter, main stop
cock or insulating insert.

4.4 Earthing

Every exposed-conductive-part (a conductive part of equipment 413-02-06

which can be touched and which is not a live part but which 413-02-18
may become live under earth fault conditions) shall be
connected by a protective conductor to the main earthing
terminal.

4.5 Supplementary Equipotential Bonding in Locations of

Increased Shock Risk - Metal Pipework

Supplementary equipotential bonding is required only in

locations of increased shock risk such as some of those in Part 6
of BS 7671 (471-08-01). In domestic premises, the locations 471-08-01
identified as having increased shock risks are rooms containing
a bath or shower (bathrooms) and around swimming pools.

In a bathroom or shower room, local supplementary equipotential 601-04-01

bonding is required to be provided connecting together the
terminal of protective conductors of each circuit supplying
Class | and Class Il equipment in zones 1, 2 or 3, and extraneous-
conductive-parts in these zones including the following:
(i) metal pipes supplying services and metallic waste pipes
(e.g. water, gas)

25
Sec 4
 (ii) metal central heating pipes and air conditioning systems
(iii) | accessible metal structural parts of the building (metal
door architraves, metal handrails, window frames and
similar parts are not considered to be extraneous-
conductive-parts unless they are connected to metallic
structural parts of the building)
(iv) metal baths and metal shower basins.

Circuit protective conductors may be used as supplementary

bonding conductors.

The supplementary equipotential bonding may be provided in

close proximity to the location.

See Section 8.1 for locations containing a bath or shower.

A typical installation is shown in Figure 4d. 601-04-01

4.6 Supplementary Bonding in other Locations - Metal 471-08-01

Pipework

There is no specific requirement in BS 7671 to supplementary

bond the following
kitchen pipes, sinks or draining boards
metal furniture in kitchens
metal pipes and wash hand basins in domestic locations
other than bathrooms.
Note: Metal waste pipes in contact with earth should be main bonded back to
the main earthing terminal.

4.7. Supplementary Bonding of Plastic Pipe Installations

Supplementary bonding is not required to metal parts

supplied by plastic pipes, such as metal hot and cold water taps
supplied from plastic pipes. A metal bath not connected to
extraneous-conductive-parts (such as structural steelwork) with
plastic hot and cold water pipes and plastic waste pipes does
not require supplementary bonding. Supplementary bonding
in a bathroom or shower room will still be required between
the protective conductors of circuits supplying Class | and Class II
equipment in the zones e.g. heaters, showers and accessible
luminaires, see Figure 4e.

26
Sec 4
 Hi4 :ep jedidA, Hulypyelsa sjusWAaHUe.e
puke 3AI}39}01d 40}9NPUOD
&S>
- S-NL

Ja}9W
Ja}aWsje}GZ ZU

A2UINsSUOD
uN
UO!}NqLJ}sIp
paeog
10
Bulyyes
Jeq

14dV1
387
| OL! ZU (a7
|| }UI! ae | (73a¥7
Hulyyes
JaY}O

je}oW

149V11 gk
sebadid

ule JEUILUI9}
sued

ulew
ulew
-SNOSUPIIXO

Joy
-3AIPNpuUuod

Hulyyes

Npuod
:S-NL payyeyZ
O} INOW
AO I1]/e}9W Y}eaYsS

yyea
Hulpuog

Ajddns
:a720/V(i uieyy jeljuaj}odinba
Hulpuog s1O}INPUOD
AeWaq a}e1edas
se) (UMOYs
Jo Paedoo]YIM UBHOIQUN *$JOJINPUOD
$40}INpuod
jelzuazodinba

(!! | -[TFGVT
Ajayes Je914999/3 UO!PaUUOD
- O JON ‘AAOWAY

ae
Sec 4
 N
00

Sec 4
614 :qy jerIdA, Hulyzies s}yuswWabH
pue uewe 3AI}39}01d 40}9NPUOdD
&S2
- S-“D-NL

Ja}
Ja}OWsje}GZ ZWIW

|
| sauinsuod
lun
JO Uuol}Nq!}sS
paeog
Ip
138V1 bulyyes
Jeq
aye}UI [1387] [138
OL WW C+ 14aV1 a
OL ZUW
| J9UO
'
ule ulew JeUa}odinba -
Bbulyyes Hulpuog S10}NPUOD -
Ajddns yea JEUIWI9} sued
oud jejow jezowW oy)
UO!}DaUUOD Jayem seb
adid adid

:S-D-NLFINd Yes
:a20//(| uleyy jeuaiodinba
HuIpUuog s10JINpUOD
Ae aq a}eJedas
se) (UMoYs
Jo padoo|YIM USYOIGUN "SJOJINPUOD
(I [207 Ayid144D9]a UO!INGIYSIP
y4OMJaU suol}IPUOd
AewW a4inbas JabHJe] "sJOPNPUOD
(1! 1) -[FAGVT
Aayes 231499919 UO!}DBUUOD
- O JON "BAOWAY
 614 :>p jeriIdAy Buiypes s}UaWabUeWe
pue 3AI}39}01d 10}9NPUOD
&S)
- LL
49}9W

GZ
7WW
sjle}
Ja}9W
}IUN

p1eogJeq
JaUINsSUOD

JO Bulyyes
UO!}NqLIA}sSIp

ulew
ZW 9 T349V1

Hulyyes
JO}NpuOD
DOL a1Ge1 Bas [138V7 |

[av]
148V1

uleuw
je}OW
jeyou
BGs rUy
seb
JayeM
yee
apoupaja adid BAid ee.
-SNOdUPI}XA
-LL YW UAN}94
SIA YPWeS 8pO1}D9]9 -89AIINPUOD
:a2ZO/y(| uley~y jeljuajodinba
Hulpuog ssO}DNPUOD
AeWaq a}eJedas
Se) (UMOYS
JO padoo|YIM UBYOIQUN “SJOJNPUOD syed
"BAOWAY JON O - UO!}D9UUOD JeI1I9/9 Ayayes -| TIGVT | (1!

N
si

uy
75,

(III
aas

a
‘OL'y

Yea

Sec 4
apOUpaja
‘pauinsai

aduejsIsad
Hulpaaaxa
UdeuBesed
 “SJOJPINPUOI ‘
“SQUOZ dU} OPISINO Iv ‘[OO} B JO ASN oY} YA ATUO sIqQISsadoR “IWR ay) JapuN seoeds
BHuipuog Aieyuawajddns ‘J00] B JO ISN JY} INOYIIM o]qGIssadov st aovds ay] Jf | WUOZ, ,
:
se pasn aq Aew siojonpuod *
BAIPDI9}OId YINDIID. 7
sulseq ve aysem jejaw
Jamoyus je}yaw pue syjyeq
fll Ld ofiii Ud
je}oOW pue ‘sadid buleay LLL” Y;—;QQutaaeeEEEEELLLdddd ddd
jesjUa> pue Ja}eM ‘ajsem .
jeyaw Bulpnyou! ‘seuoz ne ||
ay} Ul Sued-aAl}2NpuOod ‘ sadid jeyau OS
-snoauedj}xa ||e 0} papuog pes
Aueyuaweajddns ag ysnw —
SOUOZ 94} UIY}IM s}UIod
Huljy61| pue samod je 4o
SJOPNPUOD dAI}D9}0OId SUL “1
‘SOLON ,
UW 6Z'Z ¥ € QUOZ yun zouoz ss [| oUOZ we
SoUOZ apisingQ.:
: Janeys =
:
KR
@
p10 ay
: a

ASS
JaMous
€ QU0Z, Z Uu0Z

gq
souoZ apIsInC, Janne eS
sieate ap= wn aiene'= Deeeeeeaciocses
adid
Eee YD}IMs pod Te jeyow
aseUIWUN|

SS
Zi
SUH! Mee MCC
uol}E]]e}SUI adid jeyaw - WoosY}eq & Ul HUIpUOg AueyUaWa|ddns :pr BIJ

Sec 4
mo
 614 707 Aue}UsWwajddns
Hulpuog
Ul e WoOo1Yy}eq
- 31}Sse;dadid uol}e]]/e}sul

UU
CO
suo
a1yse\d UDUMs P4od ||Nd

adid

3
&
ee
ee
eb
ede
ee
ewe
wee

y Y YyY y y
weet
eee
eee
SOuO7Z,
Z OUOZ, € QUOZ

SpisynO
y

VY
y
U
couse tardeeeJamoyusSac
‘
eee ete meee eR en RECUR
Uc otaSulese Ween tc iaac Raveltsb
Y JueIPeY
diy
UIMS
YD :.
G Te a e ----|------+
fein a

y YyY
YA : :
U 13 = ; us
Jane

y —::
i:
yun
U0Z
Y .
;
‘Sa1ON
ra

woe
Y ;

¢QUOZ,
|SOUOZ
UniCE
ZTWUO0Z
9pIsINgQ
y Ao “| aU, BAIPa}OId SJO
YA
y 4o je samodpue Hulj
] Ss}UIOd UIYLIM
JU} SQUOZ
y }snuwaq Asey
y al
ay

;
0}
aq
34}

Sedid
—=
Aew

opsejd
eyo

‘papuogq
Hulpuog

ajsem
d14se|d
yes

OS
410
Wpaims

j YYY Y Yy y
oat(eeta ef eq@ LLL. Uddddddddeddddddddddddddddddddddddddddddlddddbflef
dd "juowd inba
jeuIW23
uol~aUUOD

-°Z. YINDIID 9AI9OId

Spelt wise. eeSe2
2npuod
aq
pasn
sso}
se
Aew
BulAjddns
Ayossaaoe

Pe
eee

*[00}
JO
st
ajqissaoor
Jl
ay}
5|9UOZ,
Bayy
asn
aouds
sadeds JopuN
dy) ‘YR IQISsador
ATUO YIM dy} ASN JOB ‘JOO]div OPIsINO
IU} “SQUOZ
BHulpuog

31
Sec 4
"$10}DNPUODd
Aueyuawayddns
 4.8 Earth Electrode (Fig 4c)

This is connected to the main earthing terminal by the earthing 542-01-04

conductor and provides part of the earth fault loop for a TT
installation.

It is recommended that the earth fault loop impedance for TT 542-02-02

installations does not exceed 200 ohms.

Metal gas or water or other metal service pipes are not to be 542-02-04
used as the earth electrode, although they must be bonded as
paragraph 4.1.

4.9 Types of Earth Electrode

The following types of earth electrode are recognised:

(i) earth rods or pipes 542-02-01

(ii) earth tapes or wires 542-02-01

(iii) | earth plates 542-02-01

(iv) | underground structural metalwork embedded in 542-02-01

foundations

(v) welded metal reinforcement of concrete embedded in 542-02-01

the earth (excluding pre-stressed concrete)

(vi) lead sheaths and metal coverings of cables, which must 542-02-05
meet the following conditions:
(a) the sheath or covering shall be in effective contact —542-02-05(ii)
with earth,
(b) the consent of the owner of the cable shall be 5A2-02-05\ii)
obtained, and
(c) arrangements shall be made for the owner of 542-02-05(\v)
the cable to warn the owner of the electrical
installation of any proposed change to the cable
or its method of installation which might affect
its suitability as an earth electrode.

32
Sec 4
4.10 Typical Earthing Arrangements
for Various Types of Earthing System (Figs 4a, 4b, 4c)

Figs 4a, 4b and 4c show the single-phase arrangements, but three-

phase arrangements are similar.

The protective conductor sizes shown in Figures refer to copper Table 54G
conductors and are related to 25 mmé2 supply tails from the Table 54H
meter. 547-02-01

For TT systems protected by an RCD with an earth electrode 542-03-01

resistance 1 ohm or greater, the earthing conductor size need 543-01-03
not exceed 2.5 mm¢ if protected against corrosion by a sheath
and if also protected against mechanical damage; otherwise,
see Table 10C of Appendix 10.

The earthing bar is sometimes used as the main earthing

terminal; however, means must be provided in an accessible
position for disconnecting the earthing conductor to facilitate 542-04-02
testing of the earthing.
Note: For TN-S and TN-C-S installations, advice about the availability of an
earthing facility and the precise arrangements for connection should be
obtained from the distributor or supplier.

33
Sec 4
 SECTION 5. ISOLATION AND SWITCHING

Sal Isolation

A means of isolation must be provided to enable electrically 460-01-01

skilled persons to carry out work on, or near, parts which
would otherwise normally be energised. Isolating devices must
comply with the isolation requirements of BS 1363-4, BS 3676, 511
BS EN 60669-2-4, BS EN 60898, BS EN 60947-2, BS EN 60947-3, 537-02-02
BS EN 61008-1 or BS EN 61009-1. The position of the contacts 537-02-04
must either be externally visible or be clearly, positively and 476-02-02
reliably indicated. If it is installed remotely from the
equipment to be isolated, the device must be capable of being
secured in the OPEN position.

Means of isolation should be provided as follows:

(i) at the origin of the installation, a main linked switch or 460-01-02

circuit-breaker should be provided as a means of
isolation and of interrupting the supply on load. For
single-phase household and similar supplies that may —476-01-03
be operated by unskilled persons, a double-pole device
must be used for both TT and TN systems. For
three-phase supplies an isolator must interrupt the phase 460-01-04
and neutral conductors in a TT system; in a TN-S or TN-C-S
system only phase conductors need be interrupted.
Provision shall be made for disconnecting the neutral — 460-01-06
conductor. Where this is a joint it shall be such that it is
accessible, can only be disconnected by means of a tool,
is mechanically strong and will reliably maintain
electrical continuity

(ii) other than at the origin of the installation every circuit, 476-01-02
or group of circuits, which may have to be isolated
without interrupting the supply to other circuits should
be provided with its own isolating device, which must —537-02-01
switch all live conductors in a TT system and all phase
conductors in a TN system

Every motor circuit should be provided with a readily accessible 131-14-02

device to switch off the motor and all associated equipment
including any automatic circuit-breaker.

34
Sec 5
 5.2. Functional Switching 537-05

A means of switching for interrupting the supply on load is 476-01-02

required for every circuit and final circuit.

One common switch may be used to interrupt the supply to 2476-01-01

group of circuits. Additionally, a separate switch must be
provided for every circuit which, for safety reasons, has to be 476-01-02
switched independently.

5.3 Switching Off for Mechanical Maintenance 462

A means of switching off for mechanical maintenance is 462-01-01

required where mechanical maintenance may involve a risk of
burns or of injury from mechanical movement, and may be
required for lamp replacement.

Each device for switching off for mechanical maintenance

must:
(i) be capable of switching full load current 537-03-04
(ii) be suitably located in a readily accessible position 462-01-02
(ili) be identified with a permanent label unless its purpose 462-01-02
is obvious
(iv) have either an externally visible contact gap or a 537-03-02
clearly and reliably indicated OFF position. An
indicating light should not be relied upon
(v) be selected and installed to prevent unintentional 537-03-03
reclosure, such as might be caused by mechanical
shock or vibration.

5.4 Emergency Switching 463

An emergency switch is to be provided for every part of an 476-01-01

installation which may have to be disconnected rapidly from 476-03-04
the supply to prevent or remove danger. Where there is a risk
of electric shock the emergency switch is to disconnect all live 463-01-01
conductors, except in three-phase TN-S and TN-C-S systems 460-01-04
where the neutral need not be switched.

A means of emergency stopping is also to.be provided where 463-01-05

mechanical movement of electrically actuated equipment may 476-03-02
give rise to danger.

35
Sec 5
 A plug and socket-outlet or similar device shall not be selected 537-04-02
as a device for emergency switching.

An emergency switch must be:

(i) readily accessible from the place where the danger 537-04-04
may occur
(ii) marked, preferably with a red handle or pushbutton 537-04-04
(iii) | capable of cutting off the full load current 537-04-01
(iv) of the latching type or capable of being restrained in —_537-04-05
the ‘OFF’ or ‘STOP’ position
(v) double-pole for single-phase systems 463-01-01
(vi) if operated via a relay or contactor, of adesign which —537-04-03
has fail-safe characteristics.

A fireman’s switch must be provided to disconnect the supply to 476-03-05

a high voltage installation, e.g. a neon sign, but such installations
are outside the scope of this Guide (see Regulations 476-03-05
to 07 and 537-04-06 of BS 7671). 537-04-06

36
Sec5
SECTION 6. LABELLING

6.1 Labels to be Provided

The following durable labels are to be securely fixed on or

adjacent to equipment installed in final circuits.

(i) Unexpected presence of nominal voltage (U or Uo) 514-10-01

exceeding 230 V
Where the nominal voltage (U or Uo) exceeds 230 V,
e.g. 400 V phase-to-phase, and it would not normally be
expected to be so high, a warning label stating the
maximum voltage present shall be provided where it
can be seen before gaining access to live parts.

7) Nominal voltage exceeding 230 volts (U or Uo) 514-10-01

between simultaneously accessible equipment
For simultaneously accessible equipment with terminals
or other fixed live parts having a nominal voltage (U or Uo)
exceeding 230 volts between them, e.g. 400 V phase-to-
phase, a warning label shall be provided where it can
be seen before gaining access to live parts.
(iii) Presence of different nominal voltages in the same 514-10-01
equipment

Where equipment contains different nominal voltages,

e.g. both low and extra-low, a warning label stating the
voltages present shall be provided so that it can be seen
before gaining access to simultaneously accessible live parts.

(iv) Connection of earthing and bonding conductors 514-13

A label to BS 951 durably marked with the words as follows 514-13-01

SAFETY ELECTRICAL CONNECTION - DO NOT REMOVE

shall be permanently fixed in a visible position at or near

the point of connection of
(1) every earthing conductor to an earth
electrode or other means of earthing, and
(2) every bonding conductor to extraneous-
conductive-parts, and
(3) at the main earth terminal, where it is not part
of the main switchgear.

37
Sec 6
 (v) Purpose of switchgear and controlgear 514-01-01

Unless there is no possibility of confusion, a label

indicating the purpose of each item of switchgear and
controlgear shall be fixed on or adjacent to the gear. It
may be necessary to label the item controlled, as well as
its controlgear.

(vi) Identification of protective devices 514-08-01

A protective device, e.g. fuse or circuit-breaker, shall be

arranged and labelled so that the circuit protected may
be easily recognised.
(vii) Identification of isolators 461-01-05
: , 537-02-09
All isolating devices shall be clearly and durably marked
to indicate the circuit or circuits which they isolate.
(vili) Isolation requiring more than one device 514-11-01

A durable warning notice must be permanently fixed in

a clearly visible position to identify the appropriate
isolating devices, where equipment or an enclosure
contains live parts which cannot be isolated by a single
device.

(ix) Periodic inspection and testing 514-12-01

A notice of durable material indelibly marked with the
words as follows, and no smaller than the example
shown in BS 7671,

IMPORTANT

This installation should be periodically inspected and

tested and a report on its condition obtained, as
prescribed in BS 7671 Requirements for Electrical
Installations published by the Institution of Electrical
Engineers.

Date of last inspection

Recommended date of next inspection

shall be fixed in a prominent position at the origin of

every installation. The electrician carrying out the initial

38
Sec 6
 verification must complete the notice, and it must be
updated after each periodic inspection.
(x) Diagrams 514-09

A diagram, chart or schedule shall be provided showing:

(a) the number of points, size and type of cables for
each circuit
(b) the method of providing protection against
indirect contact
(c) any circuit vulnerable to an insulation test.
The schedules of test results (Form F4) of Appendix 7 meets the
above requirement for a schedule.
(xi) | Residual current devices 514-12-02
Where an installation incorporates an RCD a notice
with the words as follows, and no smaller than the
example shown in BS 7671,

This installation, or part of it, is protected by a device

which automatically switches off the supply if an earth
fault develops. Test quarterly by pressing the button
marked ‘T’ or ‘Test’. The device should switch off the
supply and should then be switched on to restore the
supply. If the device does not switch off the supply
when the button is pressed, seek expert advice.

shall be fixed in a prominent position at or near the origin

of the installation.
(xii) | Warning notice - non-standard colours 514-14-01
If alterations or additions are made to an installation so that
some of the wiring complies with the harmonized
colours of Table 11A and there is also wiring in the old
colours, a warning notice shall be affixed at or near the
appropriate distribution board with the following
wording:

CAUTION

This installation has wiring colours to two versions of BS 7671.

Great care should be taken before undertaking extension,
alteration or repair that all conductors are correctly identified.

39
Sec 6
 SECTION 7. FINAL CIRCUITS

Tag Final Circuits 413-02-08

413-02-12
Table 7.1 has been designed to enable a radial or ring final 525-91-02
circuit to be installed without calculation where the supply is543-91-03
at 230 V single-phase or 400 V three-phase. For other voltages, app 4
the maximum circuit length given in the table must be Table ap2A
corrected by the application of the formula Table 4D2B
i ws Lt x Uo

230
where:

Lp is the permitted length for voltage Uo,

Lt is the tabulated length for 230 V
Uo is the supply voltage.

The conditions assumed are that:

(i) the installation is supplied

(a) bya TN-C-S system with a maximum external earth
fault loop impedance, Ze, of 0.35 ohm, or
(6) bya TN-Ssystem with a maximum Ze of 0.8 ohm, or
(c) aTT system with RCDs installed as described in
Section 3.6.

(ii) the final circuit is connected to a distribution board or

consumer unit at the origin of the installation

(iii) | the method of installation complies with Reference App 4

Methods 1, 3 or 6 of Appendix 4 of BS 7671:
(a) Reference Method 1 (M1)
Sheathed cables, armoured or unarmoured
clipped direct or embedded in plaster
(b) Reference Method 3 (M3)
Cables run in conduit or trunking
Single-core or insulated and sheathed

(c) Reference Method 6 (M6)

Multicore thermoplastic (pvc) insulated and sheathed — Table apsA

flat twin cable with protective conductor in conduit in
an insulating wall and also direct in a thermally

40
Sec 7
 insulating wall, or single-core thermoplastic (pvc)
insulated cables enclosed in conduit in a thermally
insulating wall (Method 15).

(iv) the ambient temperature throughout the length of the Table 4c1
circuit does not exceed 30 °C

WY) the characteristics of protective devices are in App 3

accordance with Appendix 3 of BS 7671, with a fault
current tripping time for circuit-breakers of 0.1 s or less

(vi) the cable conductors are of copper.

72 Using the Tabulated Final Circuits
72 Grouping of Cables

(i) In domestic premises, except for heating cables, the Table 4B1
conventional circuit design permits any number of
single-layer circuits when the spacing between
adjacent surfaces of the cables exceeds one cable
diameter, and, for other than semi-enclosed fuses,
(BS 3036) up to 5 touching, single-layer, circuits, when
clipped to a non-metallic surface (Installation Method 1)

(ii) up to four, 5A or 6 A circuits of enclosed or bunched Table 481

cables (Methods 3 and 6) are allowed for circuits
protected by semi-enclosed fuses to BS 3036 and up to
6 circuits when protected by BS 88 or BS 1361 fuses or
by circuit-breakers to BS 3871-1 or BS EN 60898 or
RCBOs to BS EN 61009

(iii) for other groupings and/or high ambient temperatures

and/or enclosure in thermal insulation cable sizes will
need to be increased per Appendix 6 of this Guide.

41
Sec 7
 SS
WYO GE'0 5 °Z

(BE
S-D-NL

Hua}
y
Ul
LWUNWIXe|/]
sojjoW

|
|UOID@UUODSIp
UO!}DBUUODSIP
|UO!}D@UUODSIP
UO!PaUUODSIP
(11106
LN
Buljjas

3|qe>
-OWJ9U}
uol}ze}|e3SU|
314e>

8}0u)
(!
poyjaw

984’
(and)
d13se|d
-OWJ9U}
398 984
SPINIAID

4’€’'Z‘L
JEUOIBUSAUOD

43 389 a3 38 '€'7'‘L
‘1 ‘7
BAIYE}OJg

| € 1 €
edAL
adhqd

edkl
ed, ed adAl edAL edAL
O9DY/G2
Ogd4/92

adf}
OGDU/G2Ogdu/q?
OgDu/G2 OgDU/G2 OMDHY/G2O9DH/92
ad1Aap
88
Sd
azisajqe>

Sa q>
9E0E
Zadh, qo
zadh,
|

2UuW
|°/
JIGVL

adIN0q
|

SHINDIID SHINDIID
Huizes jeipey
Bury
Ze
ad>/aseyud
2}0uU)
(A
Vv OE
Sa
LOEL S
SA
‘LOEL
Sa
QE0E S
SE
‘LOEL
SA
9E0E Sdsre
988

42
Sec 7
 F1GV1L
[7 PaNU!}UOD JEUOHUBAU
S}INIAID
OD
adIAaq
| AazIsajqeD
| BAI2}OJg a1qeD wnwixeyy
y}6ua]
ul saJjew
Burjes
|} zwiw ad!Aapadi} uoljze}/2}su|
Vv dd>jaseud
| (Aajou) pouyew 57= 80 Igo 22 SEO
9}0u)
(] S-NL S-D-NL

-OWJ2Y} -OWJ2Y} S$
Bulas | (2nd) a1se\d UoPaUUODSIP |UOIPEUUOISIp |UOHaUUODsIP |UOPEUUODsIP|
ajqe> aiqe>
leipey
9 Sd 88
OgDuU/q>
adAL ’€'Z‘L D4

s}INI4ID
Ogdu/q?
edf)
gd
OL 88S
OGDy/G2
edAL
‘L ‘7 ’€ 384
Ogdy/q?
edfj
ad
OL Sq 88
OgDuU/G>
adAL
‘L ‘7 ’€ 324
O9dy/q>
edA,
g
Sl SA 9E0E
OGDyY/G2
adAL
‘tL Z
OGDY/G>
dA]
€ g@

a8
)
Sl SA 9E0E
Sa LOEL OGDW/9?
edALZ‘L 48
OgDU/q>
edA)
€ 28
91 aL/Si Sa 88
SA LOEL OgOU/G?
edAL
‘L 2 8 ig
OgDU/G>?
edAl
€ 28
O9p4/q?
ed,
a

43
Sec 7
 (16 I qd edA| Ogdu/G?
€€ I! I! 9g € edAL OgDU/G?
€€ 9972 ‘L edAL OgDU/q>
€€ 88 Sd Sz
ZL qd adh} OgdH/9?
(WZ I > 3 ¢ adk, ODU/G>?
ev Z adh, q>
€v g 91 adh, OgDuU/G?
€v LOEL Sd ‘88S
ev 9E0E SA 0z
(OL I d edt Ogd4/9?
LZ I! I 398 ¢€ adkl OGDU/G>?
LZ 992 ‘L edAL OgDH/G?
€N 9E0E SA
12 LOEL Sa ‘'88sa 0z
(1!1)0Z (11)0Z a edAj Ogdu/9?
()9P (1)9S I I > 3 € adh, OgDH/G?
9S 9S 987 ‘L edAL O9DU/G2
9S 9S 88 Sq ol
S}INIIID
jeipey
3jqeo
UOIPsUUODSIP UOIP9UUODSIP UOIPSUUODSIP UO!P2UUODSIP Buijjas
SS -OWJ9U}
S-D-NL ((] 2}0U)
WYO SE°0 > °Z pouj}aw (Aajou) | sd>/eseyd Vv
uolze}|e}SuU| adf} ad1Aap zu Buljes
saijaw ul y}Hua] WNWwixe/\| 21Ge> 9AI}D2}01d azis ajqeD> | a21Aeq
S}INIAID FLUOMUGAUOD Peanul}uod |°/ FEVL

Sec 7
 J1gVL
17 PANU!}UOD [EUOIJUBAUOD
S}IND4ID
adINagG
| AZISajged
| BAIP2}OJg ajqe> Wnwixeyy
yyHus;
Ul seujewW
Buljzes zwiw a21Aapadf} uol}e}/e}Su|
Vv >d>/eseyd
| (Aajou) poyjew °Z> GEO WYO
. 910u)
(| S-D-NL

-OWJ2U} -OWJ9Y} ; SG
aIAse}d(2d)
| —Huljas |UOMP@UUODsIP| |UOPEUUOIsIp |UOIPaUUOdSIP UO!PSUUODSIp
ajqe> ajqe
leipey
S}INDUID
SZ ; Sd 88
Ogdy/G>
adAl
| a8
q> adA|
z
OgDy/q>
adA|
€ 8>
Ogdy/92
adhqd
O€ SE 9E0E
S@ L9EL
OgDu/G>
edAl
1 a8
q> adh,
Zz
OGDY/G>
adh|
€ 8>
O€ 0'v/0'0L SA 9E0E
SA LOEL
OgDy/G2
adAl
| a8
q> adh,
Zz
OMDU/G>
adk|
€ 28
z€ Sq 88
OgDyY/G>
adAL
| 49
qo adh,
Zz
OgDU/G>?
adh]
€ 38
Ogdy/q>
edA,
gd

45
Sec 7
 (EZ 38 € edAL O@DH/G>
60 60 z adh gD
6t 60 g adh, OgDU/9?
6t 6v a9 1 edAL OgDU/q>
6v (WE 9E0E SA
60 (W)ZE LOEL Sd Sv
(6 (W617 > 8 € adAL OGDH/9?
88 88 Z adh, q>
88 g adh Ogdu/9>
88 , adh, qo
88 88 Sd 0°9/0°91 Ov
(W)ZE > 3 € edAL O9DU/9?
€S z adh q>
€S g adAl OgDu/9>
€S | edAy qo
€S 88 Sq 0'v/0'0L Ov
(N)LS > 3 € adAL OGDH/G?
69 z edAy qo
69 a3 | edAL OgDU/9>
69 88 Sd 0'v/0'0L ze
S}INIIID
jeipey

3|qe>
Huljjes

-OWJ9Y}
UONDEUUODSIP |UOIDBUUODsIP |UOID@ULODSIP |UO!BUUODSIP
SNL (] 9}0U)
WYO 8'0 5 °Z pouyew (Aajou) | do/aseyd Vv
uo!}e}/E}SU| adh} ad1Aap zu Bulzed
sasjaw Ul yyHus] WNWwIxXe//\| 3)qeD 8A1}D9}O1d azIs ajqe> | adIAeq
S}INDAID JEUOIZUBAUOD Panu!}UOD |°/ F1GVL

Sec 7
46
Notes to Table 7.1

(i) Installation reference method

M6 indicates methods of cable installation M1, M3 and M6
may be used .
M3 indicates methods of cable installation M1 and M3 may
be used
M1 indicates method of cable installation M1 only may be
used

All the circuits are limited by voltage drop other than those marked
as below:

(ii) Length is limited by earth fault loop impedance

(iii) Alternative method of Regulation 413-02-12 applied, 413-02-12
R2 + 4 to be less than 0.30 ohm

(iv) Alternative method of Regulation 413-02-12 applied, 413-02-12

R2 + 4 to be less than 0.36 ohm

(v) Application of RCBOs, see 3.6.3

(vi) Alternative method of Regulation 413-02-12 applied, 413-02-12
R2 + 4 to be less than 0.28 ohm

N1 NOT PERMISSIBLE as 0.4 s disconnection required for

socket-outlet circuits

N2 NOT PERMISSIBLE as earth fault loop impedance too high

N3 NOT PERMISSIBLE cable overloaded

If the alternative method ((iii) or (iv)) is used, R2 must be recorded on

the installation schedule.

Reference to BS 88 fuses is to BS 88-2.1 or BS 88-6

BS 88 fuses are not available in Consumer Units.

47
Sec 7
 Table 4A2
7.2.2 Thermosetting cables (e.g. to BS 5467 or BS 7211)

Cable sizes must not be reduced when cables with

thermosetting insulati on are used, as the cable operating
tempera ture may exceed the maximu m tolerate d by the
accessory to which it is connected.

7.2.3 Checklist

Before installing a conventional final circuit the following

questions must be answered:

(i) what is the load current and can the distribution board
and supply arrangements accommodate it? (See
Appendix 1 for guidance on assessing load currents)

(ii) which kind of protective device is to be used?

(iii) | what cable type and installation method are to be used?

(iv) what rating of the protective device is equal to or next

higher than the load current of the circuit?

(v) which type of earthing arrangement is employed?

(vi) isthe maximum required disconnection time 0.4 s or Bis?

Maximum 0.4 s disconnection time is required for circuits 413-02-09
feeding socket-outlets and circuits feeding fixed 471-08-03
equipment outside the equipotential zone.
(vii) what are the isolation and switching requirements?
(See Section 5)

(viii) what labels are required? (See Section 6)

(ix) is the earth loop impedance value below the values

given in 7.1(i) or 7.2.4(ii)?

(x) is an RCD or RCBO required? All socket-outlets on a TT 471-08-06

system must be protected by an RCD or RCBO.
Socket-outlets in all systems, that may reasonably be 471-16-01
expected to supply equipment outdoors need to be
protected by an RCD or RCBO with a rated residual
operating current of 30 mA (all RCDs or RCBOs to comply
with BS 4293, BS 7288, BS EN 61008 or BS EN 61009).

Certain equipment in bathrooms requires RCD protection. 601-09-02

601-09-03

48
Sec 7
7.2.4 TT Systems

For TT systems the figures for TN-C-S systems, with 5 s disconnection

time, may be used provided that:

(i) the circuit is controlled by an RCD to BS 4293,

BS EN 61008 or BS EN 61009 with a rated residual
Operating current not exceeding 200 mA, and

(ii) the total earth fault loop impedance is verified as being

less than 200 ohms, and

(iii) a device giving both overload and short-circuit

protection is installed in the circuit. This may be an
RCBO.

7.2.5 Choice of Protective Device

The selection of protective device depends upon:

(i) prospective fault current

(ii) circuit load characteristics
(iii) cable current-carrying capacity
(iv) disconnection time limit.

Whilst these factors have generally been allowed for in the

conventional final circuits in Table 7.1, the following additional
guidance is given:

(i) prospective fault current

lf a protective device is to operate safely its rated short- 434-03-01

circuit capacity must exceed the prospective fault
current at the point it is installed.

At the origin of the installation the distributor needs to 313-01-01

be consulted as to the prospective fault current. Except
for London and some other major city centres, the
maximum fault current for 230 V single-phase supplies
up to 100 A will not exceed 16 kA.

Consumer units including protective devices complying

as a whole assembly with BS 5486-13 or BS EN 60439-3
are suitable for locations with fault currents up to 16 kA
when supplied through a type Il fuse to BS 1361 : 1971
(1992) rated at no more than 100 A.

49
Sec 7
 TABLE 7.2A

Rated Short-Circuit Capacities

Device type Device Rated

designation | short-circuit
capacity kA

Semi-enclosed fuse to BS 3036

with category of duty

Cartridge fuse to BS 1361 type | 16.5

type Il 33.0

General purpose fuse to BS 88-2.1 50 at 415 V

General purpose fuse to BS 88-6 16.5 at 240 V

80 at 415 V

Circuit-breakers to BS 3871
(replaced by BS EN 60898)

Circuit-breakers to BS EN 60898* and Ics

RCBOs to BS EN 61009 5 (1.5)
3.0 (3.0)
6 (6.0)
10 (7.5)
15 (7.5)
20 (10.0)
25 (235)
* Two rated short-circuit rating are defined in BS EN 60898 and BS EN 61009
(a) Icn the rated short-circuit capacity (marked on the device).
(b) les the service short-circuit capacity.
The difference between the two is the condition of the circuit-breaker after manufacturer's testing.
Icn is the maximum fault current the breaker can interrupt safely, although the breaker may no
longer be usable.
Ics is the maximum fault current the breaker can interrupt safely without loss of performance.
The Icn.value is normally marked on the device in a rectangle e.g.[ 6000| and for the majority of
applications the prospective fault current at the terminals of the circuit-breaker should not
exceed this value.
For domestic installations the prospective fault current is unlikely to exceed 6 kA up to which
value the Icn and Ics values are the same.
The short-circuit capacity of devices to BS EN 60947-2 is as specified by the manufacturer.

50
Sec 7
(ii) circuit load characteristics

(a) semi-enclosed fuses - fuses should preferably be of the 533-01-04

cartridge type. Semi-enclosed fuses are still commonly
used in domestic and similar premises only

(b) cartridge fuses to BS 1361 - these are for use in

domestic and similar premises

(c) cartridge fuses to BS 88 - three types are specified:

gG fuse links with a full-range breaking capacity for

general application

gM _ fuse links with a full-range breaking capacity for

the protection of motor circuits

aM fuse links with partial range breaking capacity for

the protection of motor circuits.
(d) circuit-breakers to BS 3871-1 or BS EN 60898 and RCBOs
to BS EN 61009 - guidance on the selection is given in
Table 7.2B below.

TABLE 7.2B

Instantaneous Application
trip current

domestic and commercial installations

having little or no switching surge

4.0 to 7.0 |, general use in commercial/industrial

5 to 10 In installations where the use of fluorescent
7 to 10 In lighting, small motors etc can produce
switching surges that would operate a Type
1 or B circuit-breaker. Type C or 3 may be
necessary in highly inductive circuits such as
banks of fluorescent lighting

10 to 50 In suitable for transformers X-ray machines,

10 to 20 I, industrial welding equipment etc where
high inrush currents may occur

Where In is the nominal rating of the device.

51
Sec 7
 (iii) | cable current-carrying capacities

For guidance on the co-ordination of device and cable App 3

ratings see Appendix 6 App 4

(iv) disconnection times 413-02-09

413-02-13
The protective device must operate within 0.4 or 5 seconds
as appropriate for the circuit. Appendix 2 provides
maximum permissible measured earth fault loop
impedances for fuses, circuit-breakers and RCBOs.

TES Installation Considerations

7.3.1 Floors and ceilings

When a cable is installed under a floor or above a ceiling it shall be 522-06-05

run in such a position that it is not liable to damage by contact with
the floor or ceiling or their fixings. Unarmoured cables passing
through ajoist shall be at least 50 mm from the top or bottom as
appropriate or enclosed in earthed steel conduit. Alternatively, the
cables can be provided with mechanical protection sufficient to
prevent penetration of the cable by nails, screws and the like. (Note,
the requirement to prevent penetration is difficult to meet.)
Fig 7.3.1: Cables through joists

cable in earthed insulated

steel conduit and
sheathed
y cable

greater than
50 mm joists

Notes:

ile Maximum diameter of hole should be 0.25 x joist depth.

Da Holes on centre line in a zone between 0.25 and 0.4 x span.
BF Maximum depth of notch should be 0.125 x joist depth.
4. Notches on top in a zone between 0.1 and 0.25 x span.
5s Holes in the same joist should be at least 3 diameters apart.

52
Sec 7
 7.3.2. Walls

Where a cable is concealed in a wall or partition at a depth of less 522-06-06

than 50 mm from any surface it must be enclosed in earthed metal
conduit (trunking or ducting) or installed either horizontally within
150 mm of the top of the wall or partition or vertically within 150
mm of the angle formed by two walls, or run horizontally or
vertically to an accessory or consumer unit (see Fig 7.3.2).
Fig 7.3.2: Permitted cable routes

no protection
required

wall

~<# protection required

unless depth greater
than 50 mm

Note:

A Zone formed on one side of a partition wall of 100 mm or less thickness 522-06-06
extends to the reverse side only if the location of the accessory can be
determined from the reverse side.

7.3.3 Telecommunication Circuits 528-01-02

528-01-04
An adequate separation between telecommunication wiring
(Band 1) and electric power and lighting (Band II) circuits must
be maintained. This is to prevent mains voltage appearing in
telecommunication circuits with consequent danger to personnel.
BS 6701: 1994 recommends that the minimum separation
distances given in Tables 7.3A and 7.3B should be maintained:

53
Sec 7
 TABLE 7.3A External Cables
Minimum separation distances between external low voltage
electricity supply cables operating in excess of 50 V a.c. or 120 V d.c.
to earth, but not exceeding 600 V a.c. or 900 V d.c. to earth (Band II),
and Telecommunications cables (Band 1).

Voltage to earth Normal Exceptions to normal separation

separation distances, plus conditions to
distances exception
Exceeding 50 V a.c. or Below this figure a non-conducting
120 V d.c., but not divider should be inserted between
exceeding 600 V a.c. the cables.
or 900 V d.c.

TABLE 7.3B Internal Cables

Minimum separation distances between internal low voltage
electricity supply cables operating in excess of 50 V a.c. or 120 V d.c.
to earth, but not exceeding 600 V a.c. or 900 V d.c. to earth (Band Il)
and Telecommunications cables (Band 1).

Voltage to earth Normal Exceptions to normal separation

separation distances, plus conditions to
distances exception

Exceeding 50 V a.c. or 50 mm separation need not be

120 V d.c., but not maintained, provided that
exceeding 600 V a.c.
or 900 V ae (i) the LV cables are enclosed in
separate conduit which if metallic
is earthed in accordance with
BS 7671, OR
the LV cables are enclosed in
separate trunking which if
metallic is earthed in accordance
with BS 7671, OR
(iii) the LV cable is of the mineral
insulated type or is of earthed
armoured construction

il. Where the LV cables share the same tray then the normal
separation should be met.
Zs Where LV and telecommunications cables are obliged to cross
additional insulation should be provided at the crossing point;
this is not necessary if either cable is armoured.

54
Sec 7
 7.3.4 Proximity to Other Systems 528-02
Electrical and all other services must be protected from any
harmful mutual effects foreseen as likely under conditions of
normal service. For example, cables should not be in contact 528-02-02
with or run alongside hot pipes.

The installation must comply with BS 7671, Chapter 52 and

Chapter 54, regarding separation and bonding.

A particular form of harmful effect may occur when an

electrical installation shares the space occupied by a hearing
aid induction loop.

Under these circumstances, if phase(s) and neutral or switch

feeds and switch wires are not close together, there may be
interference with the induction loop.

This can occur when a conventional two-way circuit is installed.

This effect can be reduced by connecting as shown in Fig 72314:

Fig 7.3.4: Circuit for reducing interference with induction loop

switch
feed
neutral

switch wire light

r
point

2 way switch

common

3 cores
grouped
together

pee
strappers

2 way switch

circuit shown switched

off

55
Sec7
 7.3.5 Height of switches, sockets etc

Accessories for general use, such as light switches and socket-

outlets, are required by the Building Regulations to be
located so that they can be used by people whose reach is
limited. A way of satisfying this requirement is to install
switches for lights and similar equipment and socket-outlets 553-01-06
at a height of between 450 mm and 1200 mm from finished
floor level. See Figure 8A in Appendix 8.

7.4 Smoke Alarms and Emergency Lighting

7.4.1 Smoke alarms in single dwellings

The Building Regulations 1991 and the Building Standards

(Scotland) Regulations 1990 require all new and refurbished
dwellings to be fitted with mains operated smoke alarms. The
requirements for single family dwellings of not more than two
storeys are that self-contained smoke alarms should be
installed as follows:
1) at least one on each floor
2) within 7 m of kitchens and living rooms or other areas
where fires may start e.g. integral garages
3) within 3 m of all bedroom doors.

The smoke alarm must be installed in accordance with the

manufacturer's instructions, generally on ceilings and at least
300 mm from any wall or ceiling luminaire.

The alarms are required to:-

- be interconnected so that detection of smoke by one
unit operates the alarm in all units
- be permanently wired to a separate way in the
distribution board (consumer unit), or supplied from a
local, regularly used lighting circuit.
- have battery backup

Except for TT supplies, the circuit supplying a smoke alarm

should not be protected by an RCD. For TT supplies the smoke
alarm must be supplied from the fixed equipment section, that
is not through a 30 mA RCD, see Figure 3a.

56
Sec 7
 The cable for the power supply to each self-contained unit and
for the interconnections need have no fire retardant
properties, and needs no special segregation. Otherwise, fire 528-01-04
alarm system cables generally are required to be segregated as
per BS 5839-1 and BS 5839-6, see Table 7.4.

TABLE 7.4 Segregation requirements of fire alarm and emergency

lighting standards

Fire alarms Emergency lighting

BS 5839 BS 5266

a__ installation in conduit, ducting, trunking or a channel a_ physical segregation by a

reserved for fire alarms, or minimum distance of 300 mm,
or
b amechanically strong, rigid and continuous partition
of non-combustible material, or b use of mineral cables, or

€ mounting at a distance of at least 300 mm from c cables to BS 6387 Cat B

conductors of other systems, or

d__ wiring in cables complying with BS 7629, or

e wiring in mineral insulated copper sheathed cable

with an insulating sheath or barrier. The exposed-to- Table 4J1A
touch rating of the IEE Wiring Regulations should not
be exceeded.

7.4.2. Emergency lighting

The wiring to self-contained emergency lighting luminaires is

not considered part of the emergency lighting installation and
needs no special segregation. Otherwise, emergency lighting 528-01-04
and fire alarm circuits must be separated from other cables
and from each other, in compliance with BS 5266,
see Table 7.4.

57
Sec 7
 SECTION 8. SPECIAL LOCATIONS GIVING RISE TO INCREASED
RISK OF ELECTRIC SHOCK

8.1 Locations Containing a Bath or Shower

Outed Because of the presence of water these locations are

onerous for equipment and there is an increased danger of
electric shock because of immersion of the body in water.
The additional requirements can be summarised as follows:
(i) No socket-outlets are allowed other than SELV and 601-08-01
shaver supply units — see Table 8.1.

(ii) Supplementary bonding of the terminals of the 601-04-01

protective conductors of circuits to Class | and Class II 601-04-02
equipment in the zones (see Figure 4d) to exposed-
conductive-parts in the zones is required, including:
- metal pipes both water and central heating
- metal baths and shower basins
- accessible metal structural parts of the building.
The supplementary bonding must be carried out in or in
close proximity to the zones. See Figures 4d and 4e.

(iii) Protection against ingress of moisture is specified for 601-06-01

equipment installed in the zones — see figure 4d and
Table 8.1. The requirements apply to appliances,
switchgear and wiring accessories.

(iv) There are restrictions as to where appliances, 601-08

switchgear and wiring accessories may be installed — see 601-09
Table 8.1.
8.1.2 Underfloor heating installations in these areas should 601-09-04
have an overall earthed metallic grid or the heating cable
should have an earthed metallic sheath, which must be
supplementary bonded.

58
Sec 8
 d18Vl
8
syUaWasINbay
4104 JUadINb~a
}UasIN>)
Huisnpuke (SalJOSsa22e
Ul suO!}ed0] Hulule}UOd
& y}eq40 4aMoys
s}uaWasINnbay
10} JUaLUdINba
Ul 3y} S2UO0Z
winwiiull,Al uaesindBusy (sodueljddy) 1e3a6yr}IMsS
pue SalIOssad>.y
avaibap
jo
uo1}39}0:1d
L0-80-L09
AJUO A195 paxit JUaLUCINb~a
}eU} JoUUeD
8q pa}ed0] YyMasja
‘ee| SUON ‘PaMo||e L0-60-L09
A745 }uawdinba‘pamoyjje AjUOZ| A “d°e Pue OE A *D°P SAYIUMS
JO TAS S}INDIIDL0-80-L09
e/\\193 ‘sia}eay
L0-
‘siaMous samous ‘sduind ‘pamoj|e ‘pamoyye
au} a2iNos Bulag apis}noSaUOZ
‘9| pue‘Z
AYO pexi} JUaWiNbea
Jey} JOUUeD Aj\qeuoseai
aq pazed0|
aiaymasyjapamojje
41 papajoud
Aqe OE VW Gou
A745 }uawdinba‘pemoyje /A71FS SayIUMS
pue s}ayd0s ‘paMmo}|e
ay} 841NOs Hulaq
413}e/\/\ ‘sia}eay ‘siamous Jamous ‘sduund ‘sasieuiun|
‘suey apisynosauoz
‘9| pue‘Z pue saneys Ajddnssyiun
0}
Huijesy ‘sadueljdde
syiunJo} jOod|4IyM
syzeq ‘pamoyje SA Na ZPZ09
UDZ 28S| Pamoje
AJUO
4! paxi} aJayM
; a1 Aeids WO} s4aMoUs
si ‘Aja1]UN
L0-80-109

JayIO paxil} JUaWINba

ey} JOUUeD Ajqeuosea
aq paj}ed0|
€0-60-109

siaymasja‘pamoj|e
A745 puawdinba“‘pamoyjje saliossay
pamoyjje Jdadxa
10} “S}8]JNO-18905s
B1BU|
SI

€
ON
»
OU

Aq
o}|
Jo}

e
‘pue
IsnWW

OE
‘pax

Aq
OF
Sd
NJ

ssajuN
L0-80-L09

pue

Z|

"adu
ag 13S
SHUN
ajqeyiod
77409

UOIsIAoId

pas
Janeys

P2}22I0Jd
s}a30s

deyd

sa2ue!|ddY]
Gul3298uUOd

Uauasinbau
“Juadinba

ON
‘pamoyle

|
0}
Sg
NJ

JdadxKB

Z|
pue

apisino
pamojle pamoyje
pamoj|e

A795
syiun

sauoz
ZvZ09

Pas
janeys
Ajddns JO} Ajddns

deyd

Vw sadueiddy
sjaxI0s

a10/V
:/ B1aU/\
e JaMmoys 3j2IGNI
Ss! Paj|je}SU!
U! & WOOL J8Y4}O UY}
& WOOJY}e
10 JaMoYs ‘WOO APIs}NOSAUOZ
saluossaddV

‘0 ‘| Z JO € & -J9N0S
‘}a]]NO 1830 UCU}
& A7J¥S 38]}NO-Ja4D0s
JO Janeys Ajddns‘yun |jeysaq payda}0Id
Aqe
‘pamole

jenpised }US1IND ad!AapYUM payed

"$19|1NO-}990S

Jenpisos BuleiadoJUaIIND
(4V}) JOU Hulpeaedxe
QE YWU!

“\uawasinbai
adUePIODIe
YM UO!E|NBay
py ‘90-ZL
aloyy
:z aas SauNHl4
PH pUe dp JO} “SQUOZ
€0-60-L09 LO-80-L09 c0-80-109
90-CLV

ao
Sec 8
 8.2. Shower Cubicles in a Room used for Other Purposes _—_601-08-02

Where a shower cubicle is installed in a room other than a

bathroom or shower room the requirements for bathrooms
and shower rooms are generally to be complied with, except
that socket-outlets are allowed outside zones 0, 1, 2 and 3
provided they are protected by a 30 mA RCD, and no
supplementary bonding is required in zone 3. 601-04-02

8.3 Temporary and Garden Buildings, Domestic Garages, 300-01

Buildings of Lightweight Construction etc

The use of a temporary building does not permit a lower

standard of electrical installation. The standards of installation
and maintenance need to be higher to cope with the more
onerous conditions. Particular attention must be paid to:

(i) suitability of the equipment for the environment

(ii) earthing and bonding
(iii) | connection to the supply
(iv) | use of accessories of the appropriate Degree of
Protection (IP code) to suit the particular external
influences.

8.4 Earthing requirements of Equipment having High 607

Protective Conductor Current

Equipment
Equipment having a protective conductor current exceeding 607-02-02
3.5 mA shall be either permanently connected to the fixed
wiring or connected by means of an industrial plug and socket
to BS EN 60309-2.

Equipment having a protective conductor current exceeding 607-02-03

10 mA shall be connected preferably by a permanent connection,
or an industrial plug and socket to BS EN 60309-2 with a protective
conductor csa of at least 2.5 mm? for plugs up to 16 A and at
least 4 mm2 for plugs rated above to 16 A.
Circuits
The wiring of every final circuit and distribution circuit having 607-02-04
a protective conductor current likely to exceed 10 mA shall
have high integrity protective conductor connections
comprising either:
(i) a single protective conductor complying with Section 543
and of csa not less than 10 mm2, or
60
Sec 8
 (ii) a single copper protective conductor complying with
Section 543 and of csa not less than 4 mmé2 enclosed in
conduit, or
(iii) | duplicate protective conductors, each complying with
Section 543.

Socket-outlet final circuits

For socket-outlet final circuits requiring a high integrity protective 607-03-01
conductor connection, the following arrangements are acceptable:
(i) a ring circuit with a ring protective conductor (Fig 8.4a), or
(il) a radial circuit with a single protective conductor (Fig 8.4b)
connected as a ring or an additional protective conductor
provided by conduit, trunking or ducting.

When the two protective conductors are provided the ends

must be terminated independently of each other at all
connection points e.g. distribution board and socket-outlet.
Accessories are required to have two separate earth terminals.

Fig 8.4a: Ring final circuit supplying socket-outlets

(total protective conductor current exceeding 10 mA)
DISTRIBUTION BOARD
PE
separate, i
connections

Socket-outlets must have two

terminals for protective conductors.
One terminal to be used for each
protective conductor, of a minimum
size of 1.5 mm2

Fig 8.4b: Radial circuit supplying socket-outlets

with duplicate protective conductor
DISTRIBUTION BOARD (total protective conductor current exceeding 10 mA)
PE

a
Ny
separate
connections °
a

Socket-outlets must have two

terminals for protective conductors.
Duplicate protective conductor. One terminal to be used for each
Keep close to circuit conductors protective conductor, of a minimum
to reduce emc effects. size of 1.5 mm2

61
Sec 8
 SECTION 9. INSPECTION AND TESTING Part 7

9.1. Inspection and Testing

Every installation must be inspected and tested during erection 711-01-01

and on completion before being put into service.

Precautions shall be taken to avoid danger to persons and to 711-01-01

avoid damage to property and installed equipment during
inspection and testing.

If the inspection and tests are satisfactory, a signed Electrical 741

Installation Certificate together with a Schedule of Inspections
and a Schedule of Test Results (as in Appendix 7) are to be
given to the person ordering the work.

9.2 Inspection

9.2.1. Procedure and Purpose

Inspection shall precede testing and shall normally be done 712-01-01

with that part of the installation under inspection disconnected
from the supply.

The purpose of the inspection is to verify that equipment is: —_712-01-02

(i) correctly selected and erected in accordance with

BS 7671 (and if appropriate its own standard)

(ii) not visibly damaged or defective so as to impair safety.

9.2.2 Inspection Checklist 712-01-03

The inspection shall include at least the checking of relevant

items from the following checklist:

(i) connection of conductors

(ii) identification of conductors

(iii) | routing of cables in safe zones or protected against

mechanical damage

(iv) selection of conductors for current-carrying capacity

and voltage drop, in accordance with the design

(v) connection of single-pole devices for protection or

switching in phase conductors only

62
Sec 9
(vi) correct connection of accessories and equipment
(including polarity)

(vii) presence of fire barriers, suitable seals and protection

against thermal effects

(viii) methods of protection against electric shock

(a) protection against both direct contact and indirect

contact, i.e.:

- SELV
- limitation of discharge of energy

(b) protection against direct contact (including

measurement of distances where appropriate),
1.@.:

- protection by insulation of live parts

- protection by barriers or enclosure
- protection by PELV

(c) protection against indirect contact:

- earthed equipotential bonding and automatic

disconnection of supply
presence of earthing conductor
presence of protective conductors
presence of main equipotential bonding
conductors
presence of supplementary equipotential
bonding conductors
- use of Class Il equipment or equivalent
insulation
- electrical separation

(ix) prevention of mutual detrimental influence 515

Account must be taken of the proximity of other 528

electrical services of a different voltage band and of
non-electrical services and influences.

Fire alarm and emergency lighting circuits must be 528-01-04

separated from other cables and from each other, in
compliance with BS 5839 and BS 5266, see 7.4.1 and
7.4.2.

63
Sec 9
 Band | and Band II circuit cables may not be present in 528-01-02
the same enclosure or wiring system unless they are
either separated by an effective barrier or wired with
cables suited to the highest voltage present. Where 528-01-07
common boxes are used for Band | and Band II circuits,
the circuits must be segregated by an insulating or
earthed partition.

Mixed categories of circuits may be contained in 528-01-02

multicore cables, subject to specific requirements.

Definitions of voltage bands Part 2

Band |circuit:

Circuits that are nominally extra-low i.e. not exceeding 50 V

ac or 120 V dc e.g. SELV, PELV, telecommunications, data
and signalling.

Band II circuit:

Circuits that are nominally low voltage, that is 51 to

1000 V.ac and 120 to 1500 V dc. Telecommunication
cables that are generally ELV but have ringing voltages
exceeding 50 V are Band I.

(x) presence of appropriate devices for isolation and 131-14-01

switching correctly located

(xi) presence of undervoltage protective devices (where 451

appropriate)

(xil) choice and setting of protective and monitoring devices

(for protection against indirect contact and/or
protection against overcurrent)

(xiii) labelling of circuits, cbs, RCDs, fuses, switches and 514

terminals, main earthing and bonding connections

(xiv) selection of equipment and protective measures 522

appropriate to external influences

(xv) adequacy of access to switchgear and equipment

(xvi) presence of danger notices and other warning signs

(see Section 6)

64
Sec 9
 (xvii) presence of diagrams, instructions and similar 514-09
information

(xviii) erection methods 522

(xix) requirements for special locations. 600

9.3 Testing 713

Testing must include the relevant tests from the following

checklist.

When atest shows a failure to comply, the installation must be 713-01-01

corrected. The test must then be repeated, as must any earlier
test that could have been influenced by the failure.

9.3.1 Testing Checklist

(i) continuity of protective conductors (including main and 713-02-01

supplementary equipotential bonding conductors)

(ii) continuity of ring final circuit conductors including 713-03-01

protective conductors

(iii) insulation resistance (between live conductors and 713-04

between each live conductor and earth)

(iv) polarity; this includes checks that single-pole control 713-09

and protective devices (e.g. switches, circuit-breakers,
fuses) are connected in the phase conductor only, that
bayonet and Edison-screw lampholders (except for E14
and E27 to BS EN 60238) have their outer contacts
connected to the neutral conductor and that wiring has
been correctly connected to socket-outlets and other
accessories

(v) earth electrode resistance 713-10

(vi) earth fault loop impedance 713-11

(vii) prospective fault current, if not determined by enquiry 713-12

of the distributor

(viii) functional testing (including RCDs and RCBOs). 713-13

65
Sec 9
SECTION 10. GUIDANCE NOTES ON INITIAL TESTING OF
INSTALLATIONS

10.1 Safety and equipment 711-01-01

Electrical testing involves danger. It is the tester’s duty to

ensure his or her own safety, and the safety of others, in the
performance of the test procedures. When using test
instruments, this is best achieved by precautions such as:
(i) an understanding of the correct application and use of
the test instrumentation, leads, probes and accessories
to be employed
(ii) checking that the test instrumentation is made in
accordance with the appropriate safety standards such
as BS EN 61243-3 for two-pole voltage detectors and
BS EN 61010 or BS EN 61557 for instruments
(iii) | checking before use that all leads, probes, accessories
(including all devices such as crocodile clips used to
attach conductors) and instruments are clean,
undamaged and functioning
(iv) observing the safety measures and procedures set out in
HSE Guidance Note GS 38 for all instruments, leads, probes
and accessories. It should be noted that some test
instrument manufacturers advise that their instruments
be used in conjunction with fused test leads and probes.
Other manufacturers advise the use of non-fused leads
and probes when the instrument has in-built electrical
protection, but it should be noted that such electrical
protection does not extend to the probes and leads.
10.2. Sequence of Tests 713-01-01

Note: The advice given does not preclude other test methods.

Tests should be carried out in the following sequence:

10.2.1 Before the supply is connected

(i) continuity of protective conductors, including main and
supplementary bonding
(ii) continuity of ring final circuit conductors, including
protective conductors
(iii) insulation resistance
(iv) — polarity (by continuity methods)

66
Sec 10
(v) earth electrode resistance, when using an earth
electrode resistance tester (see also vii).

10.2.2 With the supply connected

(vi) re-check of polarity
(vii) earth electrode resistance, when using a loop
impedance tester
(vill) earth fault loop impedance
(ix) prospective fault current measurement, if not
determined by enquiry of the distributor
(x) functional testing.

Results obtained during various tests should be recorded in the 741-01-01

Schedule of Test Results (Appendix 7) for future reference.

10.3. Test Procedures

10.3.1 Continuity of protective and bonding conductors 713-02-01

(except ring final circuits, see Para 10.3.2)

Test Methods 1 and 2 are alternative ways of testing the continuity

of protective conductors.

Every protective conductor including the earthing conductor,

main and supplementary bonding conductors should be tested
to verify that the conductors are electrically sound and correctly
connected.

Test Method 1 detailed below, as well as checking the continuity

of the protective conductor, also measures (Ri + R2) which,
when added to the external impedance (Ze), enables the earth-
fault loop impedance (Zs) to be checked against the design, see
Section 10.3.6. Note: (R1 + R2) is the sum of the resistances of the
phase conductor (R1) and the circuit protective conductor (R2)
between the point of utilisation and origin of the installation.

Use an ohmmeter capable of measuring a low resistance for

these tests.

Test Method 1 can only be used to measure (Ri + R2) for an ‘all
insulated’ installation. Installations incorporating steel conduit,
steel trunking, micc and pvc/swa cables will produce parallel
paths to protective conductors. Such installations should be
inspected for soundness of construction and Test Method 1 or
2 used to prove continuity.

67
Sec 10
 Jy ssayeaug |e
JO JNO sasnj {je
pseog Uol}Nq!3sIp $yO YOUMs Ue JUSWNJYsUl
$9}
UO UDd1IMs 4
Oo

poaowsal
sdwe|
ull
Asesodwia}
}INDID
‘ Jo pua je
asoJ Bulla.

-
L POUzaIA] $10}2NPUOD 3AI}39}0.1d yo A}INUIZUOD
Buljsa} 10} SUO!}DBUUOD :L'OL Bi

Sec 10
68
10.3.1(i) To test the continuity of protective conductors 713-02-01

Test Method 1

Bridge the phase conductor to the protective conductor at the

distribution board so as to include all the circuit. Then test
between phase and earth terminals at each point in the circuit.
The measurement at the circuit's extremity should be recorded
and is the value of (Ri + R2) for the circuit under test (see Fig 10.1).

If the instrument does not include an “auto-null” facility, or

this is not used, the resistance of the test leads should be
measured and deducted from the resistance readings obtained.

Test Method 2

Connect one terminal of the continuity test instrument to a

long test lead and connect this to the consumer’s main earthing
terminal.

Connect the other terminal of the instrument to another test

lead and use this to make contact with the protective
conductor at various points on the circuit, such as luminaires,
switches, spur outlets etc.

The resistance of the protective conductor R2 is recorded on

the Schedule of Test Results, form F4.

10.3.1(ii) To test the continuity of bonding conductors 713-02-01

Use Test Method 2

10.3.2. Continuity of ring final circuit conductors 713-03-01

A three step test is required to verify the continuity of the

phase, neutral and protective conductors and correct wiring of
every ring final circuit. The test results show if the ring has
been inter-connected to create an apparently continuous ring
circuit which is in fact broken, or wrongly wired.

Step 1:
The phase, neutral and protective conductors are identified
and the end-to-end resistance of each is measured separately
(see Fig10.2a). These resistances are r1, fn and r2 respectively. A
finite reading confirms that there is no open circuit on the ring
conductors under test. The resistance values obtained should
be the same (within 0.05 ohm) if the conductors are the same

69
Sec 10
 size. If the protective conductor has a reduced csa the
resistance 12 of the protective conductor loop will be
proportionally higher than that of the phase and neutral loops
e.g. 1.67 times for 2.5/1.5 mm cable. If these relationships are
not achieved then either the conductors are incorrectly
identified or there is something wrong at one or more of the
accessories.

Step 2:
The phase and neutral conductors are then connected together
so that the outgoing phase conductor is connected to the
returning neutral conductor and vice-versa (see Fig 10.2b). The
resistance between phase and neutral conductors is measured
at each socket-outlet. The readings at each of the sockets
wired into the ring will be substantially the same and the value
will be approximately one quarter of the resistance of the
phase plus the neutral loop resistances, i.e. (r1 + rn)/4. Any
sockets wired as spurs will have a higher resistance value due
to the resistance of the spur conductors.
Note: Where single-core cables are used, care should be taken to verify that the phase and
neutral conductors of opposite ends of the ring circuit are connected together. An error
in this respect will be apparent from the readings taken at the socket-outlets,
progressively increasing in value as readings are taken towards the midpoint of the
ring, then decreasing again towards the other end of the ring.

Step 3:
The above step is then repeated, this time with the phase and
cpc cross-connected (see Fig 10.2c). The resistance between
phase and earth is measured at each socket. The readings
obtained at each of the sockets wired into the ring will be
substantially the same and the value will be approximately one
quarter of the resistance of the phase plus cpc loop resistances,
i.e. (r1 + 12)/4. As before, a higher resistance value will be
recorded at any sockets wired as spurs. The highest value
recorded represents the maximum (Ri + R2) of the circuit and is
recorded on Form F4. The value can be used to determine the
earth loop impedance (Zs) of the circuit to verify compliance with
the loop impedance requirements of BS 7671 (see Appendix 9).

This sequence of tests also verifies the polarity of each socket,

except that if the testing has been carried out at the terminals
on the reverse of the accessories, a visual inspection is required
to confirm correct polarity connections, and dispenses with the
need for a separate polarity test.

70
Sec 10
Fig 10.2: Connections for testing continuity of ring final circuit conductors

10.2a

L N

EB

initial check for

continuity at
ends of ring

test
instrument

10.2¢

10.2b

N Laer N Le

connection for
taking readings of R1 + R2
at sockets

71
Sec 10
 10.3.3 Insulation resistance 713-04

Pre-test checks

10.3.3(i)

(a) pilot or indicator lamps, and capacitors are

disconnected from circuits to avoid misleading test
values being obtained
(b) if a circuit includes voltage-sensitive electronic devices
such as dimmer switches, touch switches, delay timers,
power controllers, electronic starters or controlgear for
fluorescent lamps etc either:
(1) the devices must be temporarily disconnected, or
(2) ameasurement should be made between live
conductors (phase and neutral) connected
together and the protective earth only
It should also be confirmed that there are no RCDs
incorporating electronic amplifiers, before the test is made.

10.3.3(ii)
Tests should be carried out using the appropriate d.c. test
voltage specified in Table 10.1.
The tests should be made at each distribution with the main
switch off, all fuses in place, switches and _ circuit-breakers
closed, lamps removed and other current-using equipment
disconnected. Where the removal of lamps and/or the
disconnection of current-using equipment is impracticable, the
local switches controlling such lamps and/or equipment should
be open.

72
Sec 10
Where any circuits contain two-way switching the two-way
switches must be operated one at a time and further
insulation resistance tests carried out to ensure that all the
circuit wiring is tested.

TABLE 10.1 TABLE 71A

Minimum values of insulation resistance

Circuit nominal Test Minimum

voltage voltage insulation
V d.c. resistance
(M ohms)

SELV and PELV

Up to and including 500 V with the

exception of SELV and PELV, but
including FELV

Although an insulation resistance value of not less than 0.5

megohm complies with BS 7671, where an insulation resistance
of less than 2 megohms is recorded the possibility of a latent
defect exists. Each circuit should then be tested separately, and
its insulation resistance should be greater than 2 megohms.

Where electronic devices are disconnected for the purpose of 713-04-04

the tests on the installation wiring (and the devices have
exposed-conductive-parts required by BS 7671 to be connected
to the protective conductors) the insulation resistance between
the exposed-conductive-parts and all live parts of the device
(phase and neutral connected together) should be measured
separately and should not be less than the values stated in
Table 10.1.

10.3.3(iii) Insulation resistance between live conductors 713-04

Single-phase and three-phase

Test between all the live (phase and neutral) conductors at the
distribution board (see Fig 10.3).

73
Sec 10
 74
Sec 10
B14 :¢"OL UOI}LINSU] BdDUL}SISA1
S}Sa} UBIM}9q
AAI] $10}INPUOD
JO© }INIAID

£i_|S \
LAY ee
Buljia2 Bulla.
asol asol
Ge (B) | A
Banoo, Aem-om} sayrzimMs sdwe|
paAowad
we,

3]
eee eereer PP

ule UDd}IMs
$40 . Coe Voce
asnj-}INIIID
3NO uolynq!sjs!
Jeoq
JO suayxeasg
$jO

3}OU
=], 3AI}99}01d S$410}INPUOD
O} S9YI}IMS
SACY
uaaq pa}}Iwo
10} Aj}l4e]>
a}OU
:7 }So}
3y} sa} pynoys Ajjeiziul
aq palsed
}NO UO
jUawn}sul

ay}
uo}
e]]e}SU!
3}a;dWI0
Resistance readings obtained should be not less than the
minimum values referred to in Table 10.1.

10.3.3(iv) Insulation resistance to Earth 713-04

Single-phase

Test between the live conductors (phase and neutral) and the
circuit protective conductors at the distribution board
(see Fig 10.4).

For circuits containing two-way switching or two-way and

intermediate switching the switches must be operated one at a
time and the circuit subjected to additional insulation resistance
tests.

Three-phase

Test to earth from all live conductors (including the neutral)

connected together. Where a low reading is obtained it is
necessary to test each conductor separately to earth, after
disconnecting all equipment.

Resistance readings obtained should be not less than the

minimum values referred to in Table 10.1.

10.3.3(v) SELV and PELV circuits Table 71A

Test between SELV and PELV circuits and live parts of other
circuits at 500 V d.c.

Test between SELV or PELV conductors at 250 V d.c. and between

PELV conductors and protective conductors of the PELV circuit
at 250 V d.c.

10.3.3(vi) FELV circuits 471-14-03

FELV circuits are tested as LV circuits at 500 V d.c.

75
Sec 10
 HI4 :y"OL UOI}EINSU] d2uUe}SISA1
S}S9}
O} Yes

Sec 10
ae }---
r a | ae ease
i
ee jit i
vf
Do Ks K
BS fea asol
Buia.

Bsa
Buijia.
A

|
sdwe|
paaowsas
ial

sauryums

Aem-om}
pavowa

OLE Ona eed

bcc ae

3}0U
:1 9AI}I9}01d S10}INPUOD
O} S29YI}IMS
BALY
uaeq pazzIwo
40} Ajlie]> }S9}
a}OU
:7 9y} Sa} pynoys AjjeiIUu!
aq palsies
}NO UO jUaUUNI}sSUI
ay} 3}a;dWI0>d UO!}L]]/e}SUI
 uosipZ
8€Z09
*P2IJLIBA
SAapjoyduie;
yo Ly pue £7]
O} Sd NJ
uo!3Nq!3sSIp

O} 3q
pieog

Ayiiejod
BAeY
suayeaug
JO
Ul]

S280p}OU
maids
Asesodwa}
Stel
18h
Ts]
18)
ie
U8
IS
Tsls

= ay}
40}INPUOD

YdIMs
sasnj

:a}0u
|e
ule
JNO
$40
BAI}I9}O1d {je
JO
:310N
iND419
0} 40}
payiwo
ugaqAjse}9
Y}IMS
sey

Hurzyb1

e
Uo
3s9}
zu
Ayejod

:¢°OL }S9}
USIP
M2J9S
Japjoudwe|
jUauNIysuUl
B14

77
Sec 10
 10.3.4 Polarity 713-09

See Figure 10.5.

The method of test prior to connecting the supply is the same

as Test Method 1 for checking the continuity of protective
conductors which should have already been carried out (see
10.3.1, 10.3.2 and Figs 10.1 and 10.2). For ring circuits a visual
check may be required (see 10.3.2 following step 3).

It is important to confirm that:

(i) overcurrent devices and single-pole controls are in the —713-09-01
phase conductor
(ii) except for E14 and E27 lampholders to BS EN 60238, 713-09-01
centre contact screw lampholders have the outer
threaded contact connected to the neutral and
(iii) | socket polarities are correct. 713-09-01

After connection of the supply polarity must be checked using

a voltmeter or a test lamp (both with leads complying with
~ HSE Guidance Note GS 38).

10.3.5 Earth Electrode Resistance 713-10

If the electrode under test is being used in conjunction with an

RCD protecting an installation, the following method of test
may be applied.

A loop impedance tester is connected between the phase

conductor at the origin of the installation and the earth
electrode with the test link open, and a test performed. This
impedance reading is treated as the electrode resistance and is
then added to the resistance of the protective conductor for
the protected circuits. The test should be carried out before
energising the remainder of the installation.

The measured resistance should meet the following criteria and 542-02-02
those of 10.3.6 but in any case should not exceed 200 ohms:

For TT systems, the value of the earth electrode resistance Rain 413-02-20
ohms multiplied by the operating current in amperes of the
protective device IAn shall not exceed 50 V e.g. if Ra = 200 Q, then
the maximum RCD operating current should not exceed 250 mA.

Remember to replace the test link.

78
Sec 10
 10.3.6 Earth Fault Loop Impedance 713-11

The earth fault loop impedance (Z;) is required to be 413-02-10

determined for the furthest point of each circuit. It may be 413-02-11
determined 413-02-14
- by direct measurement of Zs
- by direct measurement of Ze at the origin and adding
(R1 + R2) measured during the continuity tests (10.3.1
and 10.3.2) (Zs = Ze + (R1 + R2))
- by adding (Ri + R2) measured during the continuity
tests to the value of Ze declared by the distributor,
(see 7.1(i)). The effectiveness of the distributor’s earth
must be confirmed bya test.
The external impedance (Z.) may be measured using a phase-
earth loop impedance tester.
The main switch is opened and made secure to disconnect the
installation from the source of supply. The earthing conductor
is disconnected from the main earthing terminal and the
measurement made between phase and earth of the supply.
Remember to reconnect the earthing conductor to the
earth terminal after the tests.
Direct measurement of Z; can only be made on a live
installation. Neither the connection with earth nor bonding
conductors are disconnected. The reading given by the loop
impedance tester will usually be less than Z. + (R; + R2) because
of parallel earth return paths provided by any bonded
extraneous-conductive-parts. This must be taken into account
when comparing the results with design data.
Care should be taken to avoid any shock hazard to the testing
personnel and to other persons on site during the tests.

The values of Z; determined should be less than the value given 413-02-08
in Appendix 2 for the particular overcurrent device and cable. 543-01-03

For TN systems, when protection is afforded by an rcd, the 413-02-16

rated residual operating current in amperes times the earth
fault loop impedance in ohms should not exceed 50 V. This test
should be carried out before energising other parts of the
system.

Note: For further information on the measurement of earth fault loop

impedance, refer to Guidance Note No 3 — Inspection and Testing.

79
Sec 10
 10.3.7 Measurement of prospective fault current 713-12-01

It is not recommended that installation designs are based on 434-02-01

measured values of prospective fault current, as changes to the
distribution network subsequent to the completion of the
installation may increase fault levels.

Designs should be based on the maximum fault current 313-01-01

provided by the distributor (see 7.2.5(i)).

lf it is desired to measure prospective fault levels this should be

done with all main bonding in place. Measurements are made
at the distribution board between live conductors and between
phase conductors and earth.

For three-phase supplies the maximum possible fault level will

be approximately twice the single-phase to neutral value. (For
three-phase to earth faults, neutral and earth path impedances
have no influence.)

10.3.8 Functional testing 713-13

RCDs should be tested as described in Section 11. All assemblies 713-13-02

including switchgear, controls, and interlocks should be
functionally tested; that is, operated to check that they work
and are properly fixed etc.

80
Sec 10
SECTION 11. OPERATION OF RESIDUAL CURRENT OPERATED DEVICES
(RCDs) AND RESIDUAL CURRENT BREAKERS WITH
OVERCURRENT PROTECTION (RCBOs) 713-13-01

115] General Test Procedure

The tests are made on the load side of the RCD, as near as
practicable to its point of installation, and between the phase
conductor of the protected circuit and the associated circuit
protective conductor. The load supplied should be disconnected
during the test.

1 Je General purpose RCDs to BS 4293

(i) with a leakage current flowing equivalent to 50 % of

the rated tripping current, the device should not open.

(ii) with a leakage current flowing equivalent to 100 % of

the rated tripping current of the RCD, the device should
open in less than 200 ms. Where the RCD incorporates
an intentional time delay it should trip within a time
range from ‘50 % of the rated time delay plus 200 ms’ to
‘100 % of the rated time delay plus 200 ms’.

General purpose RCCBs to BS EN 61008 or RCBOs to

BS EN 61009

(i) with a leakage current flowing equivalent to 50 % of

the rated tripping current of the RCD the device should
not open.

(ii) with a leakage current flowing equivalent to 100 % of

the rated tripping current of the RCD, the device should
open in less than 300 ms unless it is of ‘Type S’ (or
selective) which incorporates an intentional time delay.
In this case, it should trip within a time range from 130 ms
to 500 ms

RCD protected socket-outlets to BS 7288

(i) with a leakage current flowing equivalent to 50 % of

the rated tripping current of the RCD the device should
not open

(ii) with a leakage current flowing equivalent to 100 % of

the rated tripping current of the RCD, the device should
open in less than 200 ms

81
Sec 11
 11.5 Additional Requirement for Supplementary Protection 412-06-02

Where an RCD or RCBO with a rated residual operating

current Ian not exceeding 30 mA is used to provide
supplementary protection against direct contact, with a test
current of 5lan the device should open in less than 40 ms. The
maximum test time must not be longer than 40 ms, unless the
protective conductor potential rises by less than 50 V. (The
instrument supplier will advise on compliance).

11.6 Integral Test Device 713-13-02

An integral test device is incorporated in each RCD. This device

enables the electrical and mechanical parts of the RCD to be
verified, by pressing the button marked ‘T’ or ‘Test’.

Operation of the integral test device does not provide a means

of checking:

(a) — the continuity of the earthing conductor or the

associated circuit protective conductors, or

(b) any earth electrode or other means of earthing, or

(a) any other part of the associated installation earthing.

The test button will only operate the RCD if the RCD is
energised.

Confirm that the notice to test RCDs quarterly (by pressing the 514-12-02
test button) is fixed in a prominent position ((see 6.1(xi)).

82
Sec 11
 APPENDICES
CONTENTS

Appendix Page
1 Maximum demand and diversity 84

2 Maximum permissible measured earth

fault loop impedance 88

Notes on the selection of types of cable

and flexible cord for particular uses and
external influences 94

Notes on methods of support for cables,

conductors and wiring systems 100

Cable capacities of conduit and trunking 109

Current-carrying capacities and voltage

drop for copper conductors Lil

Certification and reporting 127

Standard circuit arrangement for household

and similar installations 150

Resistance of copper and aluminium

conductors I

10 Protective conductor sizing 161

fit Identification of conductors 164

83
 APPENDIX 1

MAXIMUM DEMAND AND DIVERSITY

This Appendix gives some information on the determination of

the maximum demand for an installation and includes the
current demand to be assumed for commonly used equipment.
It also includes some notes on the application of allowances for
diversity.

The information and values given in this Appendix are intended

only for guidance because it is impossible to specify the
appropriate allowances for diversity for every type of
installation and such allowances call for special knowledge and
experience. The figures given in Table 1B, therefore, may be
increased or decreased as decided by the engineer responsible
for the design of the installation concerned. For blocks of
residential dwellings, large hotels, industrial and large
commercial premises, the allowances are to be assessed by a
competent person.

The current demand of a final circuit is determined by

summating the current demands of all points of utilisation and
equipment in the circuit and, where appropriate, making an
allowance for diversity. Typical current demands to be used for
this summation are given in Table 1A.

The current demand of a circuit supplying a number of final

circuits may be assessed by using the allowances for diversity
given in Table 1B which are applied to the total current demand
of all the equipment supplied by that circuit and not by
summating the current demands of the individual final circuits
obtained as outlined above. In Table 1B the allowances are
expressed either as percentages of the current demand or,
where followed by the letters f.l., as percentages of the rated
full load current of the current-using equipment. The current
demand for any final circuit which is a conventional circuit
arrangement complying with Appendix 8 is the rated current
of the overcurrent protective device of that circuit.

An alternative method of assessing the current demand of a

circuit supplying a number of final circuits is to summate the
diversified current demands of the individual circuits and then
apply a further allowance for diversity. In this method the
allowances given in Table 1B are not to be used, the values to

84
Appx 1
be chosen being the responsibility of the designer of the
installation.

The use of other methods of determining maximum demand is

not precluded where specified by a suitably qualified electrical
engineer. After the design currents for all the circuits have been
determined, enabling the conductor sizes to be chosen, it is
necessary to check that the limitation on voltage drop is met.

TABLE 1A
Current demand to be assumed for points of utilisation and
current-using equipment
Point of utilisation or current-using Current demand to be assumed
equipment

Socket-outlets other than Rated current

2 Asocket-outlets and other than
13 A socket-outlets see note 1

2 A socket-outlets At least 0.5 A

Lighting outlet see note 2 Current equivalent to the connected
load, with a minimum of 100 W per
lampholder
Electric clock, shaver supply unit May be neglected
(complying with BS 3535), shaver
socket-outlet (complying with
BS 4573), bell transformer, and
current-using equipment of a rating
not greater than 5 VA
Household cooking appliance The first 10 A of the rated current
plus 30 % of the remainder of the
rated current plus 5 A if a
socket-outlet is incorporated in the
control unit
All other stationary equipment British Standard rated current, or
normal current

Note 1: See Appendix 8 for the design of standard circuits using socket-
outlets to BS 1363-2 and BS 4343.
Note 2: Final circuits for discharge lighting must be arranged so as to be
capable of carrying the total steady current, viz. that of the lamp(s)
and any associated gear and also their harmonic currents. Where
more exact information is not available, the demand in volt-amperes
is taken as the rated lamp watts multiplied by not less than 1.8. This
multiplier is based upon the assumption that the circuit is corrected
to a power factor of not less than 0.85 lagging, and takes into
account control gear losses and harmonic current.

85
Appx 1
 TABLE 1B
Allowances for diversity

Purpose of Type of premises

final circuit
fed from
conductors or Individual household Small shops, Small hotels,
switchgear to installations stores, offices boarding houses,
which diversity including individual and business guest houses, etc
applies dwellings of a block premises

1. Lighting 66 % of total current 90 % of total 75 % of total

demand current demand current demand

2. Heating and 100 % of total 100 % f.l. of 100 % f.l. of

power (but see current demand up largest appliance largest appliance
3 to 8 below) to 10 amperes +50 % +75 % f.l. of +80 % f.l. of
of any current remaining second largest
demand in excess of appliances appliance +60 %
10 amperes f.l. of remaining
appliances

3. Cooking 10 amperes +30 % f.l, 100 % f.l. of 100 % f.l. of

appliances of connected cooking largest appliance largest appliance
appliances in excess +80 % f.l. of +80 % f.l. of
of 10 amperes +5 second largest second largest
amperes if appliance +60 % appliance +60 %
socket-outlet f.1. of remaining f.l. of remaining
incorporated in appliances appliances
control unit

4. Motors not applicable 100 % f.l. of 100 % f.l. of

(other than lift largest motor largest motor
motors which +80 % f.l. of +50 % f.l. of
are subject to second largest remaining motors
special motor +60 % f.1.
consideration of remaining
motors

5. Water-heaters 100 % f.|. of largest 100 % f.l. of 100 % f.l. of

(instantaneous appliance +100 % f.l. largest appliance largest appliance
type)* of second largest +100 % f.|. of +100 % f.l. of
appliance +25 % f.. second largest second largest
of remaining appliance +25 % appliance +25 %
appliances f.l. of remaining f.l. of remaining
appliances appliances

86
Appx 1
TABLE 1B continued Allowances for diversity

Purpose of Type of premises

final circuit
fed from
conductors or Individual household} Small shops, Small hotels,
switchgear to installations stores, offices boarding houses,
which diversity including individual | and business guest houses, etc
applies dwellings of a block | premises

6. Water-heaters
(thermostatically no diversity allowablet
controlled)

7. Floor warming
installations no diversity allowablet

8. Thermal
storage space no diversity allowablet
heating
installations

9. Standard 100 % of current 100 % of current demand of largest

arrangement of | demand of circuit +50 % of current demand of
final circuits in largest circuit every other circuit
accordance with | +40 % of current
Appendix 8 demand of every
other circuit

10. Socket-outlets 100 % of current 100 % of current | 100 % of current

other than those demand of demand of demand of
included in 9 largest point of largest point of | largest point of
above and utilisation , utilisation utilisation
stationary +40 % of current +70 % of current} +75 % of current
equipment other | demand of every demand of every | demand of every
than those listed | other point of other point of other point in
above utilisation utilisation main rooms
(dining rooms,
etc) +40 % of
current demand
of every other
point of
utilisation

* For the purpose of this Table an instantaneous water-heater is deemed to

be a water-heater of any loading which heats water only while the tap is
turned on and therefore uses electricity intermittently.
t It is important to ensure that the distribution boards and consumer units
are of sufficient rating to take the total load connected to them without
the application of any diversity.

87
Appx 1
APPENDIX 2

MAXIMUM PERMISSIBLE MEASURED EARTH FAULT LOOP

IMPEDANCE

The tables in this Appendix provide maximum permissible 713-11

measured earth fault loop impedances (Zs) for compliance with 413-02-05
BS 7671 where the conventional final circuits of Table 7.1 are 413-02-10
used. The values are those that must not be exceeded in the 413-02-11
tests carried out under Para 10.3.6 at an ambient temperature 413-02-14
of 10°C to 20°C. Table 2E provides correction factors for other 543-01-03
ambient temperatures.

Where the cables to be used are to Tables 4, 7 or 8 of BS 6004 or

Tables 3, 5, 6 or 7 of BS 7211 or are other thermoplastic (pvc) or
thermosetting (Isf) cables to these British Standards, and the
cable loading is such that the maximum _ operating
temperature is 70 °C, then Tables 2A, 2B and 2C give the
maximum earth loop impedances for circuits with:
(a) protective conductors of copper and having from
1 mm2 to 16 mmé2 cross-sectional area,
(b) where the overcurrent protective device is a fuse to
BS 88 Part 2 or Part 6, BS 1361 or BS 3036.

For each type of fuse, two tables are given:

- where the circuit concerned feeds socket-outlets and the
disconnection time for compliance with Regulation
413-02-09 is 0.45, and 413-02-09
- where the circuit concerned feeds fixed equipment only
and the disconnection time for compliance with Regulation
413-02-13 is 5s. 413-02-13

In each table the earth fault loop impedances given correspond

to the appropriate disconnection time from a comparison of
the time/current characteristic of the device concerned and the
equation given in Regulation 543-01-03. 543-01-03

The tabulated values apply only when the nominal voltage to

Earth (Uo) is 230 V.

Table 2D gives the maximum measured Zs for circuits protected

by circuit-breakers to BS 3871-1 and BS EN 60898, and RCBOs
to BS EN 61009.

88
Appx 2
Note: The impedances tabulated in this Appendix are lower than those in
Table 41B1, Table 41B2 and Table 41D of BS 7671 as these are measured
values at an assumed conductor temperature of 10 °C, whilst those in
BS 7671 are design figures at the conductor normal operating temperature.

TABLE 2A Semi enclosed fuses

Maximum measured earth fault loop impedance (in ohms) when
overcurrent protective device is a semi-enclosed fuse to BS 3036 (see Note)

(i) 0.4 second disconnection 413-02-05

Table 41B1

Protective Fuse rating (amperes) eae

conductor

1.0
1:5 8.00 2.14 1.48 0.91 NP
2.5 to 16.0 1.48

(ii) 5 seconds disconnection 413-02-05

Table 41D
Protective Fuse rating (amperes) 5943-01-03
conductor
(mm?)

1.0
des NP
2 1.20
4.0 to 16.0

Note: A value of k of 115 from Table 54C of BS 7671 is used. This is suitable for Table 54C
pvc insulated and sheathed cables to Tables 4, 7 or 8 of BS 6004 and for
Isf insulated and sheathed cables to Tables 3, 5, 6 or 7 of BS 7211. The k
value is based on both the thermoplastic (pvc) and thermosetting (Isf)
cables operating at a maximum temperature of 70 °C.

NP protective conductor, fuse combination NOT PERMITTED.

89
Appx 2
 TABLE 2B BS 88 fuses
Maximum measured earth fault loop impedance (in ohms) when
overcurrent protective device is a fuse to BS 88
A : (see Note)
(i) 0.4 second disconnection 413-02-05
Table 41B1
; . 543-01-03
Protective Fuse rating (amperes)
conductor

1.0 lila 22©) |e) | EAS) | 20) | ORGS NP

eS eit |et2© e222.6}|e 4S) |e 20)| OL Si7, ne NP
2.5 to 16.0 7.11] 4.26] 2.26] 1.48} 1.20} 0.87} 0.69] 0.51

(ii) 5 seconds disconnection 413-02-05

Table 41D
543-01-03
Protective Fuse rating (amperes)
conductor

6.0 to 16.0

Note: A value of k of 115 from Table 54C of BS 7671 is used. This is suitable for Table 54C
pvc insulated and sheathed cables to Tables 4, 7 or 8 of BS 6004 and for
Isf insulated and sheathed cables to Tables 3, 5, 6 or 7 of BS 7211. The k
value is based on both the thermoplastic (pvc) and thermosetting (Isf)
cables operating at a maximum temperature of 70 °C.

NP protective conductor, fuse combination NOT PERMITTED.

90
Appx 2
TABLE 2C
Maximum measured earth fault loop impedance (in ohms) when
overcurrent protective device is a fuse to BS 1361
: see Note
(i) 0.4 second disconnection ( 413-02-05
Table 41B1

Protective Fuse rating (amperes) 5943-01-03

conductor
(mm?)
5 15 20 30

1.0 8.72 2.74 1.42 0.80 NP

1-5 8.72 2.74 1.42 0.96 0.34
255) tOmioL0 8.72 Zale ea 0.96

(ii) 5 seconds disconnection

Table 41D

Protective Fuse rating (amperes)

conductor
(mm?)

6.0 to 16.0

Note: A value of k of 115 from Table 54C of BS 7671 is used. This is suitable for Table 54C
pvc insulated and sheathed cables to Tables 4, 7 or 8 of BS 6004 and for
Isf insulated and sheathed cables to Tables 3, 5, 6 or 7 of BS 7211. The k
value is based on both the thermoplastic (pvc) and thermosetting (Isf)
cables operating at a maximum temperature of 70 °C.

NP protective conductor, fuse combination NOT PERMITTED.

91
Appx 2
 92
Appx 2
F1EVL
dé eI9GeL CaLy
WuNWIXeEY peunseaw
YES 3jNe} doo] a2Uepaduu!
Ul) (SUYO UDYM JUSLINI4aAOBAI}39}01d
B21ABpP
St & 499C94G-}1NI419
0}
Sa L-LZ8E
AO Sd NA 86809
40 & OdDH
Lv S0-Z0-€
9} Sd NI 600L9
1)( 4IOq70 pue
¢ Spuodas UOI}DBUUODS
S@UI1}IP

-VINDID

ad}
Jayeaigq
(Seuedwe)

J9C31G-INDIID
:azloy anjeny
Jo4 Jo SLL WO4} 1421DyG40 Sd L/9/ SI “Pasn SIU]
SI ajqeyins
JOJ IAd pajze/nsu!
pue payyeays
saiqe>
0} $O
PUB
/8JO}
Sd
7009
410
S9|qe1
v7'
4s| pajejnsul
pue payjyeaus
sajqe>
0} S9/qe]
‘¢ 4109's4O SG “LLZZ AUL¥ ANjeA
si paseq
UO YOG ay} 313se|dowUay}
(rAd) pue Bulneso
(S|)
sajqed Huljeiado
je e WnuwIxew Bunjzesadwa}
$O OL ‘Do
TABLE 2E

Ambient temperature correction factors

Ambient Correction factors (from

temperature °C 10 °C) notes 1, 2

Notes:
1 - The correction factor is given by: {1 + 0.004 (Ambient temp - 10} where
0.004 is the simplified resistance coefficient per °C at 20 °C given by BS 6360
for both copper and aluminium conductors

2 - The factors are different to those of Table 9B because Table 2E corrects

from 10 °C and Table 9B from 20 °C. The values in Tables 2A to 2D are for a 10 °C
ambient.

The ambient correction factor of Table 2E is applied to the

earth fault loop impedances of Tables 2A to 2D if the ambient
temperature is not within the range 10 °C, to 20 °C. For
example, if the ambient temperature is 25 °C the measured
earth fault loop impedance of a circuit protected by a 32 A
type 1 mcb should not exceed 1.50 x 1.06 = 1.59 Q.

93
Appx 2
 APPENDIX 3

NOTES ON THE SELECTION OF TYPES OF CABLE AND

FLEXIBLE CORD FOR PARTICULAR USES AND EXTERNAL
INFLUENCES

For compliance with the requirements of Chapter 52 for the ch52

selection and erection of wiring systems in relation to risks of
mechanical damage and corrosion, this Appendix lists in two
tables types of cable and flexible cord suitable for the uses
intended. These tables are not intended to be exhaustive and
other limitations may be imposed by the relevant Regulation
of BS 7671, in particular those concerning maximum permissible
operating temperatures.

Information is also included in this Appendix on protection

against corrosion of exposed metalwork of wiring systems.

TABLE 3A
Applications of cables for fixed wiring

Type of cable Comments

Thermoplastic (pvc) In conduits, cable ducting or (i) intermediate support may be

or thermosetting trunking required on long vertical runs
insulated (ii) 70 °C maximum conductor
non-sheathed temperature for normal wiring
grades — including thermosetting
types (4)
(iii)cables run in pvc conduit shall not
operate with a conductor
temperature greater than 70 °C (4)

Flat thermoplastic (i) general indoor use in dry (i) additional protection may be
(pvc) or or damp locations. May necessary where exposed to
thermosetting, be embedded in plaster mechanical stresses
insulated and (ii) on exterior surface walls, (ii) protection from direct sunlight may
sheathed boundary walls and the be necessary. Black sheath colour is
like better for cables in sunlight
(iii)overhead wiring (iii)see Note (4)
between buildings (6) (iv) unsuitable for embedding directly
(iv) underground in conduits in concrete
or pipes (v) may need to be hard drawn (HD)
(v) in building voids or ducts copper conductors for overhead
formed in situ wiring (Note 6)

94
Appx 3
 TABLE 3A continued
Applications of cables for fixed wiring

Split-concentric General (i) additional protection may be

thermosetting (pvc) necessary where exposed to
insulated and mechanical stresses
sheathed (ii) protection from direct sunlight may
be necessary. Black sheath colour is
better for cables in sunlight

Mineral insulated General With overall pvc covering where

exposed to the weather or risk of
corrosion, or where installed
underground, or in concrete ducts

Thermoplastic or General (i) additional protection may be

thermosetting necessary where exposed to
insulated, mechanical stresses
armoured, (ii) protection from direct sunlight may
thermoplastic be necessary. Black sheath colour is
sheathed better for cables in sunlight

Paper insulated, General, for main With armouring where exposed to

lead sheathed and | distribution cables severe mechanical stresses or where
served installed underground
Notes:
1 - The use of cable covers (preferably conforming to BS 2484) or equivalent
mechanical protection is desirable for all underground cables which might
otherwise subsequently be disturbed. Route marker tape should also be installed,
buried just below ground level.
2 - Cables having thermoplastic (pvc) insulation or sheath should preferably not be
used where the ambient temperature is consistently below 0 °C or has been
within the preceding 24 hours. Where they are to be installed during a period of
low temperature, precautions should be taken to avoid risk of mechanical
damage during handling. A minimum ambient temperature of 5 °C is advised in
BS 7540 : 1994 for some types of pvc insulated and sheathed cables
3 - Cables must be suitable for the maximum ambient temperature, and shall be protected
from any excess heat produced by other equipment, including other cables.
4 - Thermosetting cable types (to BS 7211 or BS 5467) can operate with a conductor
temperature of 90 °C. This must be limited to 70 °C when drawn into a conduit
etc. with thermoplastic (pvc) insulated conductor (521-07-03) or connected to
electrical equipment (512-02-01 and 523-01-01), or when such cables are installed
in plastic conduit or trunking.
5 - For cables to BS 6004, BS 6007, BS 7211, BS 6346, BS 5467 and BS 6724, further
guidance may be obtained from those standards. Additional advice is given in
BS 7540 : 1994 "Guide to use of cables with a rated voltage not exceeding 450/750 V"
for cables to BS 6004, BS 6007 and BS 7211.

95
Appx 3
 6 - Cables for overhead wiring between buildings must be able to support their own
weight and any imposed wind or ice/snow loading. A catenary support is usual
but hard drawn copper types may be used.

Migration of plasticiser from thermoplastic (pvc) materials

Thermoplastic (pvc) sheathed cables, including thermosetting

insulated with thermoplastic sheath e.g. Isf, must be separated
from expanded polystyrene materials to prevent take up of
the cable plasticiser by the polystyrene as this will reduce the
flexibility of the cables.

Thermal insulation

Thermoplastic (pvc) sheathed cables in roof spaces must be

clipped clear of any insulation made of expanded polystyrene
granules.

Cable clips

Polystyrene cable clips are softened by contact with

thermoplastic (pvc). Nylon and polypropylene are unaffected.

Grommets

Natural rubber grommets can be softened by contact with

thermoplastic (pvc). Synthetic rubbers are more resistant.
Thermoplastic (pvc) grommets are not affected, but could
affect other plastics.

Wood preservatives

Thermoplastic (pvc) sheathed cables should be covered to

prevent contact with preservative fluids during application.
After the solvent has evaporated (good ventilation is
necessary) the preservative has no effect.

Creosote

Creosote should not be applied to thermoplastic (pvc)

sheathed cables because it causes decomposition, solution,
swelling and loss of pliability.

96
Appx 3
TABLE 3B
Applications of flexible cables and cords to BS 6500 : 2000 and BS 7919 : 2001 generally

Type of flexible cord Uses

Light thermoplastic (pvc) insulated Indoors in household or commercial premises in

and sheathed dry situations, for light du

Ordinary thermoplastic (pvc) (i) indoors in household or commercial premises,

insulated and sheathed including damp situations, for medium duty
(ii) for cooking and heating appliances where not
in contact with hot parts
(iii)for outdoor use other than in agricultural or
industrial applications
(iv) electrically powered hand tools

60 °C thermosetting (rubber) Indoors in household or commercial premises

insulated braided twin where subject only to low mechanical stresses
and three-core

60 °C thermosetting (rubber) (i) indoors in household or commercial premises

insulated and sheathed where subject only to low mechanical stresses
(ii) occasional use outdoors
(iii)electrically powered hand tools

60 °C thermosetting (rubber) (i) general, unless subject to severe mechanical

insulated oil-resisting and stresses
flame retardant sheath (ii) fixed installations protected in conduit or other
enclosure

85 °C thermosetting (rubber) General, including hot situations, e.g. night

insulated HOFR sheathed storage heaters and immersion heaters

85 °C heat resisting thermoplastic General, including hot situations, e.g. for pendant
(pvc) insulated and sheathed luminaires

150 °C thermosetting (rubber) (i) at high ambient temperatures

insulated and braided (ii) in or on luminaires

185 °C glass fibre insulated For internal wiring of luminaires only and then
single-core twisted twin and only where permitted by BS 4533
three-core

185 °C glass fibre insulated braided (i) dry situations at high ambient temperatures
circular and not subject to abrasions or undue flexing
(ii) wiring of luminaires
Notes:
1 - Cables and cords having thermoplastic (pvc) insulation or sheath should preferably
not be used where the ambient temperature is consistently below 0 °C. Where
they are to be installed during a period of low temperature, precautions should
be taken to avoid risk of mechanical damage during handling.

97
Appx 3
 2 - Cables and cords shall be suitable for the maximum ambient temperature, and
shall be protected from any excess heat produced by other equipment, including
other cables.
3 - For flexible cords and cables to BS 6007, BS 6141 and BS 6500 further guidance may
be obtained from those standards, or from BS 7540 : 1994 "Guide to use of cables
with a rated voltage not exceeding 450/750 V".
4 - When used as connections to equipment flexible cables and cords should be of the
minimum practical length to minimise danger and in any case of such a length
that allows the protective device to operate correctly.
5 - When attached to equipment flexible cables and cords should be protected against
tension, crushing, abrasion, torsion and kinking particularly at the inlet point to
the electrical equipment. At such inlet points it may be necessary to use a device
which ensures that the cable is not bent to an internal radius below that given in
the appropriate part of Table 4 of BS 6700. Strain relief, clamping devices or cord
guards should not damage the cord.
6 - Flexible cables and cords should not be used under carpets or other floor
coverings, or where furniture or other equipment may rest on them. Flexible
cables and cords should not be placed where there is a risk of damage from traffic
passing over them.
7 - Flexible cables and cords should not be used in contact with or close to heated
surfaces, especially if the surface approaches the upper thermal limit of the cable
or cord.

Protection against corrosion of exposed metalwork or 522

wiring systems

In damp situations, where metal cable sheaths and armour of 522-03

cables, metal conduit and conduit fittings, metal ducting and 522-05
trunking systems, and associated metal fixings, are liable to
chemical deterioration or electrolytic attack by materials of a
structure with which they may come in contact, it is necessary
to take suitable precautions against corrosion.

Materials likely to cause such attack include:

- materials containing magnesium chloride which are used

in the construction of floors and dadoes,

- plaster undercoats contaminated with corrosive salts,

- lime, cement and plaster, for example on unpainted walls,

- oak and other acidic woods,

- dissimilar metals likely to set up electrolytic action.

98
Appx 3
Application of suitable coatings before erection, or prevention
of contact by separation with plastics, are recognized as
effective precautions against corrosion.

Special care is required in the choice of materials for clips and 522-05-02
other fittings for bare aluminium sheathed cables and for 522-05-03
aluminium conduit, to avoid risk of local corrosion in damp
situations. Examples of suitable materials for this purpose are
the following:

- porcelain,

- plastics,

- aluminium,

- corrosion-resistant aluminium alloys,

- zinc alloys complying with BS 1004,

- iron or steel protected against corrosion by galvanizing,

sherardizing etc.

Contact between bare aluminium sheaths or aluminium 522-05-02

conduits and any parts made of brass or other metal having a
high copper content should be especially avoided in damp
situations, unless the parts are suitably plated. If such contact is
unavoidable, the joint should be completely protected against
ingress of moisture. Wiped joints in aluminium sheathed cables
should always be protected against moisture by a suitable
paint, by an impervious tape, or by embedding in bitumen.

99
Appx 3
APPENDIX 4 522-08

NOTES ON METHODS OF SUPPORT FOR CABLES,

CONDUCTORS AND WIRING SYSTEMS

This Appendix describes examples of methods of support for 522-08

cables, conductors and wiring systems which should satisfy the
relevant requirements of Chapter 52 of BS 7671. The use of
other methods is not precluded where specified by a suitably
qualified electrical engineer.

Cables generally
Items 1 to 8 below are generally applicable to supports on
structures which are subject only to vibration of low severity
and a low risk of mechanical impact.

de For non-sheathed cables, installation in conduit

without further fixing of the cables, precautions being
taken against undue compression or other mechanical
stressing of the insulation at the top of any vertical
runs exceeding 5 m in length.

2 For cables of any type, installation in ducting or

trunking without further fixing of the cables, vertical
runs not exceeding 5 m in length without
intermediate support.

33 For sheathed and/or armoured cables installed in

accessible positions, support by clips at spacings not
exceeding the appropriate value stated in Table 4A.

4. For cables of any type, resting without fixing in

horizontal runs of ducts, conduits, cable ducting or
trunking.

5: For sheathed and/or armoured cables in horizontal

runs which are inaccessible and unlikely to be disturbed,
resting without fixing on part of a building, the surface
of that part being reasonably smooth.

6. For sheathed-and-armoured cables in vertical runs

which are inaccessible and unlikely to be disturbed,
supported at the top of the run by aclip anda
rounded support of a radius not less than the
appropriate value stated in Table 4E.

100
Appx 4
 For sheathed cables without armour in vertical runs
which are inaccessible and unlikely to be disturbed,
supported by the method described in Item 6 above;
the length of run without intermediate support not
exceeding 2 m for a lead sheathed cable or 5 m for a
thermosetting or thermoplastic sheathed cable.

For thermosetting or thermoplastic (pvc) sheathed

cables, installation in conduit without further fixing of
the cables, any vertical runs being in conduit of suitable
size and not exceeding 5 m in length.

Cables in particular conditions

oh In caravans, for sheathed cables in inaccessible spaces

such as ceiling, wall and floor spaces, support at
intervals not exceeding 0.25 m for horizontal runs
and 0.4 m for vertical runs.

10. In caravans, for horizontal runs of sheathed cables

passing through floor or ceiling joists in inaccessible
floor or ceiling spaces, securely bedded in thermal
insulating material, no further fixing is required.

ile For flexible cords used as pendants, attachment to a

ceiling rose or similar accessory by the cord grip or other
method of strain relief provided in the accessory.

12; For temporary installations and installations on

construction sites, supports so arranged that there is
no appreciable mechanical strain on any cable
termination or joint.

Overhead wiring

a3: For cables sheathed with thermosetting or

thermoplastic material, supported by a separate
catenary wire, either continuously bound up with the
cable or attached thereto at intervals; the intervals not
exceeding those stated in Column 2 of Table 4A.

101
Appx 4
 14. Support by a catenary wire incorporated in the cable
during manufacture, the spacings between supports
not exceeding those stated by the manufacturer and
the minimum height above ground being in accordance
with Table 4B.

15: For spans without intermediate support (e.g. between

buildings) of thermoplastic (pvc)-insulated
thermoplastic (pvc)-sheathed cable, or thermosetting-
insulated cable having an oil-resisting and
flame-retardant or HOFR sheath, terminal supports so
arranged that no undue strain is placed upon the
conductors or insulation of the cable, adequate
precautions being taken against any risk of chafing of
the cable sheath, and the minimum height above
ground and the length of such spans being in
accordance with the appropriate values indicated in
Table 4B.

16; Bare or thermoplastic (pvc)-covered conductors of an

overhead line for distribution between a building and a
remote point of utilisation (e.g. another building)
supported on insulators, the lengths of span and
heights above ground having the appropriate values
indicated in Table 4B or otherwise installed in
accordance with the Electricity Supply Regulations 1988
(as amended).

ee For spans without intermediate support (e.g. between

buildings) and which are in situations inaccessible to
vehicular traffic, cables installed in heavy gauge steel
conduit, the length of span and height above ground
being in accordance with Table 4B.

Conduit and cable trunking

18. Rigid conduit supported in accordance with Table 4C.

19: Cable trunking supported in accordance with Table 4D.

20. Conduit embedded in the material of the building.

Z2Ae Pliable conduit embedded in the material of the

building or in the ground, or supported in accordance
with Table 4C.

102
Appx 4
 avi
Vb
sbuideds
jo syioddns
10} Sajqe>
Ul a/qISsad.e SUO!}ISOd

winwixey| sbuldeds
Jo sdij>

||/EIBAC J3JBWIP peinowJe-uoN ‘Huljjasowsey} d1Sse|doway}

10 pea] paunowuy
sajqed |esaul|/\ pajzejnsulJaddod
fo x9/Qe) payuyeaus
sa|qe>) pay}eays
JO

sajqe
payzeays

|yjeyUuOZIIOYH
— yjerxue,
| [yjequoziuoH
= yjeraueA
| fJWUOZOH
wniuiwnye

iG € v S 9
pIe2!19A 8
6
glee

4/&}U0ZLOH

WWW
Jon Bulpaa.xa
6 008

2x3 Bulpsa
6
pue jou BHulpasoxea
GL 0SZ 00” 0021
JO)|je (SAZIS
| 404)||P (SEZIS
Bulpsaax3
G|
pue jou Hulpaadxa
OZ 0002

Bulpaaaxy
0z@
pue jou Hulpaasxa
Ov

:a20/) 104 ay} Hulseds

jo soddns
404 sajqe> Bulaey
ue |je1aA0 Jajaweip Hulpaedxe
Oy ‘WW pue 10} 3109-a|buls
Sa|qe>
HulAeYy sIOJINPUOD
JO |EUO!}DAS-ssO1D
BAJe OYE ,WLW pue ‘Jabse]
34} $,jain}2ej;NUeW suoiwepuawWWoOdal
pjnoys
aq ‘paMasqo
y JOY JeI} Sa}qed UdHxe}
Se 34} UOISUBWIP
JO BY} JOfeWW"sixe
4 ay) sHulsedspayeys
JO} je}UOZIOY
sun Aewaq paljddeOsjeO} suNJJe Ue ajHue
Jo BOW ULY}OE WO} BY} “EIA
JO4 SUNIJE
ue ajHue
JO ,OE JO Ssaj WO} BY} ‘}EdIVAA
ay} jed1L198A sbudedsaie “ajqeoi|dde

103
Appx 4
TABLE 4B
Maximum lengths of span and minimum heights above ground for overhead
wiring between buildings etc

Minimum height of span above

ground

In positions
accessible
to vehicular In positions
Maximum traffic, inaccessible
length of At road | other than to vehicular
Type of system span crossings] crossings traffic*
1 2 3 4 5

¥ i‘

Cables sheathed with

thermoplastic (pvc) or
having an oil-resisting and 3.5
flame-retardant or HOFR
sheath, without
intermediate support.
(Item 15)
|

Cables sheathed with

thermoplastic (pvc) or
having an oil-resisting and 5.8 5.8
flame-retardant or HOFR 3 3
sheath, in heavy gauge
steel conduit of diameter
not less than 20 mm and
not jointed in its span.
(Item 17)

Thermoplastic (pvc) covered

overhead lines on insulators
without intermediate 30 5.8 5.8 3.5
support.
(Item 16)

Bare overhead lines on

insulators without
intermediate support. 5.8 5r2Z
(Item 16)

104
Appx 4
TABLE 4B continued
Maximum lengths of span and minimum heights above ground for overhead
wiring between buildings etc

Minimum height of span above

ground

In positions
accessible
to vehicular | In positions
Maximum traffic, inaccessible
length of At road | otherthan | to vehicular
Type of system span crossings| crossings traffic *
1

Cables sheathed with

thermoplastic (pvc) or
having an oil-resisting and No limit 3.5
flame-retardant or HOFR
sheath, supported by a
catenary wire. (Item 13)

Aerial cables incorporating Subject to

a catenary wire. (Item 14) Item 14 3.5

Bare or thermoplastic (pvc)

covered overhead lines
installed in accordance with No limit Be.
the Overhead Line
Regulations (Item 16).

* This column is not applicable in agricultural premises.

Note: In some special cases, such as in yacht marinas or where large cranes are present,
it will be necessary to increase the minimum height of span above ground given
in Table 4B. It is preferable to use underground cables in such locations.

105
Appx 4
 “LINPUOD aU} JO Ja}@WEIP apIs}NO ay} Saw} G°Z UEY} $S2] JOU aq PjNoys puaq }NPUOd e 4O sniped JSUU! aul
‘und sy ul payoddns aq 0} paau jou saop }! Jey} Y}HuUa] YINs Jo aq PINOYs HNPUOD 9/q!xe}} VE
“sBUITY JO spUag JO WLU QOE UIYIM PauO!}isod aq pynoys syuoddns ‘uni s} ul payuoddns
aq 0} pasinbad AjjewsOU JOU SI }INPUOD a/qIxXEI} VY ‘pasn ae s4ajdnod Huluay}Huaijs jeisads a18yM JO ‘pamo)|O}
ay ‘7
ag snw suOo!NJYsU! SJaun}eynueW ay} asayM ‘Hulyunsy uolsuadsns 6ulzy61| 0 Ajdde you op sasnbiy aroge
U!
"ssd.1]S JEDIUCYIOWW 19Y}O 0} pasodxe Jou Ss! HupyjuNds} JO JINPUOD 84} 3e4} eluNsse Aaul ‘spaepueys ysiziig JUeAS|a1 34}
ay]*|
paipoeds s}iwl| jewUJay} ay} pue suo!}zejnBay au Aq payqiwuad sajqed 40 [ly wWinwIxeW Jo} Moje pazejnge} sbuldeds
'Sa10N
OL Ov Dulpaasx3
30 Ot Hulpea sxe jou pue Gz Bulpee dx
90 Gz Bulpeedxe JOU pue 9| Hulpee 2x4
S‘0 9| Bulpae axe JON

WWW
fs 9 S v € ¢c
jedV2/\ je}UOZIIOH jeriwa/ je}UOZIIOH jera/ je}UOZIIOH
UINpuUOd JO azis |eUILION
a!G2lld Burejnsur pibry jeyows pibiy
suioddns uaamjaq a2uejsIp WNWIXe|\
s}iInpuOd 410} sjioddns jo shuldeds
ov 1dVL

Appx 4
106
 Appx 4
107
‘sBulnqly JO spuagq Jo WW OE UUM pauOl}sod aq pjnoys syioddns “uni s} ul peyoddns
aq 0} pauinbas AjjeWOU }OU SI }INPUOD a|qIXaI} V ‘Pasn aie siajdnod Buluay}buaijs jeIdeds a194yM 10 ‘pamo}|O}
JaunpeynueW ay} aiaym ‘Hulyuns} uoisuadsns Huljy61| 0} Ajdde you op sainbiy aroge au *Z
ag ysnw suoINJysU! S$
"§S}S |EDIUPYIOW J9Y}O O} pasodxa }OU Ss! HulyUNJ} JO JINPUOD ay} Fey} atuNsse ABY] “spsepueys Ysiiig JUeAS|94 34} U!
paijioads sjiwl| eWay} ay} pue suo!}e;nBay au} Aq payjiwuad sajqed Jo ||lJ WNWIXeW 104 Mo||e pazeinge} sbuldeds ay] “|

‘S810
07 0005 BHulpaaax
072 0005 Bulpaaaxea jou pue 90¢z Hulpsedx3
GOL 00SZ BHulpaesxe you pue QOS] Hulpas 2x3
S‘0 00S| Buipeasxe jou pue 99/ +Hulpeedx3
00Z S5uipeasxe jou pue 99¢ Hulpaedx3
v € ¢c
S

jena je}UOZIIOH jed1V9/\ Je}UOZIIOH Huryuns} Jo ease |eUO!P~aS-ssolD

Bulzeynsul
suioddns usamjeq a duejsip WNwIxey\|
BHuiyjuns} ajqe> 103 syioddns jo shulseds
ar J1aVL
TABLE 4E
Minimum internal radii of bends in cables for fixed wiring

Finish Overall diameter* Factor to be

Insulation
applied to
overall diameter
of cable to
determine
minimum internal
radius of bend

Not exceeding
Thermosetting or 10 mm
thermoplastic (pvc) Non-armoured
(circular, or circular Exceeding 10 mm
stranded copper or but not 4(3)t
aluminium exceeding 25 mm
conductors)
exceeding 25 mm 6

Thermosetting or Armoured or
thermoplastic (pvc) non-armoured
(solid aluminium or
shaped copper
conductors)

Mineral Copper sheath | Any

with or
without
covering

* For flat cables the diameter refers to the major axis.

+ The figure in brackets relates to single-core circular conductors of stranded
construction installed in conduit, ducting or trunking.
+ Mineral insulated cables may be bent to a radius not less than 3 times the cable
diameter over the copper sheath, provided that the bend is not re-worked, i.e.
straightened and re-bent.

108
Appx 4
APPENDIX 5

CABLE CAPACITIES OF CONDUIT AND TRUNKING

A number of variable factors affect any attempt to arrive at a 522-08-01

standard method of assessing the capacity of conduit or 522-08-02
trunking. 522-08-03

Some of these are:

- reasonable care (of drawing-in)
- acceptable use of the space available
- tolerance in cable sizes
- tolerance in conduit and trunking.

The following tables can only give guidance of the maximum

number of cables which should be drawn in. The sizes should
ensure an easy pull with low risk of damage to the cables.

Only the ease of drawing-in is taken into account. The

electrical effects of grouping are not. As the number of
circuits increases the installed current-carrying capacity
of the cable decreases. Cable sizes have to be increased
with consequent increase in cost of cable and conduit.

It may therefore be more attractive economically to divide the

circuits concerned between two or more enclosures.

If thermosetting cables are installed in the same conduit or

trunking as thermoplastic (pvc) insulated cables, the conductor
operating temperature of any of the cables must not exceed
that for thermoplastic (pvc) i.e. thermosetting cables must be
rated as thermoplastic (pvc).

The following three cases are dealt with:

Single-core thermoplastic (pvc) insulated cables

(i) in straight runs of conduit not exceeding 3 m in length.

Tables 5A & 5B

(ii) in straight runs of conduit exceeding 3 m in length, or

in runs of any length incorporating bends or sets.
Tables 5C & 5D

(iii) in trunking. Tables 5E & 5F.

109
Appx 5
 For cables and/or conduits, not covered by this Appendix advice
on the number of cables which can be drawn in should be
obtained from the manufacturers.

Single-core thermoplastic (pvc) insulated cables in straight

runs of conduit not exceeding 3 m in length.

For each cable it is intended to use, obtain the factor from

Table 5A.

Add the cable factors together and compare the total with the
conduit factors given in Table 5B.

The minimum conduit size is that having a factor equal to or

greater than the sum of the cable factors.

TABLE 5A TABLE 5B
Cable factors for use Conduit factors for use
in conduit in in
short straight runs short straight runs

Conductor Conduit
Type of cross-sectional diameter | Conduit
conductor area mm? mm factor

16 290

20 460

25 800

32 1400

Stranded . 38 | 1900
50 3500

63 5600

110
Appx 5
Single-core thermoplastic (pvc)-insulated cables in straight
runs of conduit exceeding 3 m in length or in runs of any
length incorporating bends or sets.

For each cable it is intended to use, obtain the appropriate

factor from Table 5C.

Add the cable factors together and compare the total with the
conduit factors given in Table 5D, taking into account the
length of run it is intended to use and the number of bends
and sets in that run.

The minimum conduit size is that size having a factor equal to

or greater than the sum of the cable factors. For the larger
sizes of conduit multiplication factors are given relating them
to 32 mm diameter conduit.

TABLE 5C

Cable factors for use in conduit in long straight runs over 3 m, or

runs of any length incorporating bends

Type of Conductor cross-sectional Cable

conductor area mm? factor

Solid 16
or 22
Stranded

The inner radius of a conduit bend should be not less than 2.5
times the outside diameter of the conduit.

111
Appx 5
 (40}De} WW ZE) XZ BSN Jay@WeIP WLU EQ JOJ
(40}9e4 WwW ZE€) X: ONC te aia osn J9}IWEeIpP WW Qs 404
(40pe} WLW ZE) X pL °° BSN Ja}OWeIP WWW BE 1O4 s10Pe4 [EUOIIPPY
OL

ce v Sv S 9 l 8 6
g pue Vv €
Sc
c69009 vLV

09c_ ~=oiLHL 98
sajqgel a
6¢S

c6~ Ss OSL 16
c€€ BL LLL cL
88E ELC O€L Aq pasenoD L
spueq Jno4 spueg ses, spueg OML puagq aud qyb1e135 WW

jo und
ce Sc 0c QL SZ Oza OL CGM OCEEEOL SZ 0c GZ 0Z~—OPLs Huy
Ww ‘Ja}aWeIp JINPUOD
sun }461e13s Huo] pue spuaq Hulzesodooul suns 104 s10}zDe4 B]qQeD
as a1aVl

Appx 5
112
Single-core thermoplastic (pvc)-insulated cables in
trunking

For each cable it is intended to use, obtain the appropriate

factor from Table 5E.

Add all the cable factors so obtained and compare with the
factors for trunking given in Table 5F.

The minimum size of trunking is that size having a factor equal

to or greater than the sum of the cable factors.

TABLE 5E
Cable factors for trunking

Conductor PVC, Thermosetting

Type of conductor cross-sectional BS 6004 BS 7211
area mm? Cable factor Cable factor

Stranded

Note:

(i) These factors are for metal trunking and may be optimistic for
plastic trunking where the cross-sectional area available may be
significantly reduced from the nominal by the thickness of the wall
material.

(ii) The provision of spare space is advisable; however, any circuits

added at a later date must take into account grouping. Appendix 4,
BS 7671.

113
Appx 5
 TABLE 5F
Factors for trunking

Dimensions of Dimensions of
trunking trunking Factor
mm xmm mm
x mm
Ea

50 x 38 200 x 100
50 x 50 200 x 150 13001
75x25 200 x 200 17429
75 x 38 225 x 38 3474
75x50 225 x 50 4671
7 Xa 225x75 7167
100 x 25 225 x 100 9662
100 x 38 225 x 150 14652
100 x 50 225 x 200 19643
100 x 75 225 x 225 22138
100 x 100 300 x 38 4648
150 x 38 300 x 50 6251
150 x 50 300 x 75 9590
150x 75 300x 100 12929
150 x 100 300 x 150 19607
150 x 150 300 x 200 26285
200 x 38 300 x 225 29624
200 x 50 300 x 300 39428
200 x 75

Space factor - 45 % with trunking thickness taken into account

For other sizes and types of cable or trunking

For sizes and types of cable trunking other than those given in
Tables 5E and 5F, the number of cables installed should be such
that the resulting space factor does not exceed 45 % of the
net internal cross-sectional area.

Space factor is the ratio (expressed as a percentage) of the sum

of the overall cross-sectional areas of cables (insulation and
any sheath) to the internal cross-sectional area of the trunking
or other cable enclosure in which they are installed. The
effective overall cross-sectional area of a non-circular cable is
taken as that of a circle of diameter equal to the major axis of
the cable.

Care should be taken to use trunking bends etc which do not

impose bending radii on cables less than those required by
Table 4E.

114
Appx 5
 APPENDIX 6 Ch 52

CURRENT-CARRYING CAPACITIES AND VOLTAGE DROP FOR

COPPER CONDUCTORS

Current-carrying Capacity

For full information on the selection of cables including 523-01-01

calculation of voltage drop see Appendix 4 of BS 7671. App 4

In this simplified approach it is presumed that the overcurrent

device will be providing both fault and overload current
protection.

Procedure

(1) the design current lb of the circuit must be established

(2) the overcurrent device rating In is then selected so 433-02-01

that In is greater than or equal to Ib 433-02-02

In = Ib

The tabulated current-carrying capacity of the selected

cable kt is then given by

Ik> Bide
C3 Cj Cg Cr

for simultaneously occurring factors.

Where :
Ca _ is the correction factor for ambient temperature, App 4,4
see Tables 6A1 and 6A2
CG is the correction factor for thermal insulation,
see Table 6B
Cg is the correction factor for grouping,
see Table 6C
Cr isthe correction factor 0.725 for semi-enclosed fuses 433-02-03
to BS 3036

115
Appx 6
 Voltage Drop

To calculate the voltage drop in volts the tabulated value of

voltage drop (mV/A/m) has to be multiplied by the design App 4,7
current of the circuit (Ib), the length of run in metres (L), and
divided by 1000 (to convert to volts)
(mV/A/m) x Ib x L
voltage drop = 1000

The requirements of BS 7671 are deemed to be satisfied for a

230 V supply, if the voltage drop between the origin of the
installation and a_ socket-outlet or fixed current-using
equipment does not exceed 9.2 V at full load. 525-01-02

TABLE 6A1 Ambient Temperature Factors

Correction factors for ambient temperature where protection is
Table 4C1
against short-circuit and overload

Ambient temperature °C

Type of Operating
insulation temperature 5)SOR|ES5 Als || 5X0) |] (S55 65

Thermoplastic
(general
purpose pvc)
le adel é.

Note: Where the device is a semi-enclosed fuse to BS 3036 the table only
applies where the device is intended to provide short-circuit protection only.

TABLE 6A2 Ambient Temperature Factors

Correction factors for ambient temperature where the overload
protective device is a semi-enclosed fuse to BS 3036 Table 4C2

Ambient temperature °C

Type of Operating
insulation temperature | 25 | 30 | 35 | 40] 45] 50] 55 65

Thermoplastic
(general
purpose pvc)

116
Appx 6
Thermal Insulation 523-04

Where a cable is to be run in a space to which thermal insulation

is likely to be applied, the cable shall wherever practicable be
fixed in a position such that it will not be covered by the
thermal insulation. Where fixing in such a position is
impracticable the cross-sectional area of the cable shall be
appropriately increased.

For a cable installed in a thermally insulated wall or above a

thermally insulated ceiling, the cable being in contact with a
thermally conductive surface on one side, current-carrying
capacities are tabulated in Tables 6D and 6E, Method 4 being
the appropriate Reference Method; and Table 6F Installation
Methods 6 and 15.

For a single cable likely to be totally surrounded by thermally

insulating material over a length of more than 0.5 m, the
current-carrying capacity shall be taken, in the absence of more
precise information, as 0.5 times the current-carrying capacity
for that cable clipped direct to a surface and open (Reference
Method 1).

Where a cable is totally surrounded by thermal insulation for

less than 0.5 m the current-carrying capacity of the cable shall
be reduced appropriately depending on the size of cable length
in insulation and thermal properties of the insulation. The
derating factors in the table are appropriate to conductor sizes
up to 10 mm? in thermal insulation having a thermal
conductivity (A) greater than 0.0625 Wm'K"!.

TABLE 6B Thermal Insulation Table 52A

Cables surrounded by thermal insulation

Length in insulation Derating factor

(mm)

50
100 0.81
200 0.68
400 0.55
500 and over

117
Appx 6
 (EL pours) suoddns
=> LL0 | 8£0 | 8Z:0 | 8Z°0 | 6Z'0 | 08'0 | Z8'0 | 98°0 Jappe| Uo Buly ano} a40313;NW Jahe| ajHuls
jedII9/\ (LL pouraw)
S30
Hulyono} ‘Aes} ajqed
je}owW pa}esojied e
s8'0 jejuozOH| uo a109-a/buys 4ahe| aj6uls
xpareds (LL Pour)

oa
So
JEJUOZIIOY JO |edIJ8A
Res} ajqed je}awW pa}esojed
Hulysnol| e uo a709/7/NW JaKe| ajHuls

co :
De

Xe)
So
o
xpeoeds

So
or
=
(L Pour)
ade LNs 51|)/e}@W-UOU
BulysnoL 2 0} paddy) saAe] ajbuis

co
So
a)
(L Pours)
80 | 6E'0 | Lv'0 | Ev'0 | Sv’'0 | 8r'0 | 050 | Z5°0 | 7S'0 | Z9°0 S90 | 0Z'0 | 080 e0} Paulp paddl|>
adepns d1|]2}aWW-UOU
pue paysung JO (710 € POUJsI/|) Peso}>uy
S8|qeD B4OIII|NW JO S}INIIID JO JAQUINN
(8) 40392} UO!}D9II0D
xx 2]/Qe) 341031}/NW SUO UCU} sJOW JO ‘sojqe> 3109-a]6uis JO }INDAID BUO ULY} DIOW JO sdnoib AO} S10}IE} UOIPIIAIOD
Lay age siopey Buldnos5 59 31EVL

Appx 6
118
 Appx 6
119
* pajejnge} jou 10e} UO!}DIIIOD
‘LZ9L SG 40 ZAP BIGeL Bas sajqe> pazejnsul jesaUuIW 104
"$2|GeD (W-N) 0} Hulpuodsas0d 1039e4 Huljzes dnoib ay} Bulsn Aq pazis aq ued sajqed 19430 34}
saiaduue 455 ¢'9 Ue} Ja}2016 JOU aJe YDIYM speo| Aed dnosb ay} Ul Sajqe> [I 4! ‘JAABMOH “4 payejnqe} ay}
0} patjdde ®> yo 10;9e} UOIINpas dnoJb e auinbas AjjewsOU pjnom sajqe) pepeo| N Jo dnoJb e ‘ajdwexa 104
‘dnoi6 au} 40 3sa4 ay} JO} Jopey Hulzes ay} Hurureygo yo asodind ay} Joy pasoubl aq Aew 7! ‘burjes
padnoib sil Jo % OF UeY} a10W JOU AuJed 0} payadxea SI ajqed e ‘suo!}puo? Hul}e4ado UMOUY 0} Buimo ‘}}
‘dnoib
ay} ul sajqe> ay} $o Aue Aq pale aq 0} JUaIIND WINWIXeWW a4} SI S1O}Ie} ayelidoudde ay} 4o uoljed1|dde
WOJJ PAALAP }UIIUND JO aNjeA BY] “aZIs BUO Jo |]e Sa}qe>d Jo sdnoJb 0} ajqedijdde ae 9/qe} ay} U! SOP! BYL
‘dnos6 au} ul ajqed Aue jo asnzesadua} Buljzesado ysamo| ay} UOdN paseq aq |jeys
Burzes JUaLND ay} 494}960} pednosb ase sainjesadiua} Hulyesado 10JNpuOD Hulayjip Huirey sajqed Usy
‘paijdde aq paau 1032} UO!}DI1I09 OU ®qZ Spaedxa sajqed Juare[pe UBaMjeq sadUeJeAa|>
j2JUOZOY ay} aay “2q Ja}@WeIP a]/GeD aUO jsea] Je JO SadeJUNs JUaDe[pe UBaMjeq adUeJea]9 e Aq pardeds
‘D9 ATAVL OL SALON
 LL OL
‘ye aseud | d°e aseyd } |!0j,01] 10 }!0494} 10
-334Y} -3ajy} | Buryonoy | Hurysno} | Burysno} | Hurydno}
sa}qe> € JO]sajqed € 10] pue ie} pue pue je}, | pue .ej}
‘ye aseyd | “dp Jo *2°e | ‘d"p Jo “d"e| “d"e ase |e] “D"p 40] “d°e aseyd | “d"p JO “D°e| ‘De aseud |‘D"p Jo ‘3"e} ‘d"e aseud | *d"p 40 “d°e
-334Y} aseud aseud -901y} | ‘de aseyd| -aa1y} aseud -33JU} aseud -991U} aseud
“10421 -3|6uls -3|6uls ‘sajqeo -3|Huls ‘sajqeo -9|6uls ‘sa|qe> -9|/6uls ‘sajqeo -9|/Huls
sajqed¢€ | ‘sajqedz | ‘sajqed 7 pjioe ‘sa|qed Z p4jioe ‘Sa|qed Z p4joe ‘Sa|qed Z p4jioe ‘Sa|qed Z
paseds podeas (JEd!SA JO (918 bulyunsy (a3 [Jem Huljzeynsul eve
el} +e|} jezuozioy Aes} ajqed Ul JO [JEM e UO Ajjeway} ul Jeuolpes
Lopes jedwap |je}UOZIOH po}eJOjJad e uo) (Wes1p paddy) }INPUOD UI paso|dUe) }INPUOD UI Paso|dUa) -SSOJD
(ule 8844) ZL POUJSI) BDUDIIJOY LL pou BuaJajoy | POU] BDUSIBJaY | € POYJS/\| BdUSIBJOyY p Pou BuUdJeJay |40}DNpUOD
7009 S@ (Sesedwy) ALIDWdVD ONIAYYVD-LNIYYND
J. OL iaunjzessdwa} Huljzesado 10]9NPuUOD ‘dD, OF :eunjyesodwa} JusIquy
(SHOLDNGNOD YAddOD)
yzeays }NoYM JO YM ‘pasnowue-uOU ‘(| 3}0U) UORe]NSU! HUIZZaSOWIAY} JO (2d) 21)se]dou494} Bulaey sajqe> 2402-2/6uls
aigeL VLOr Lqg9
414aVL

Appx 6
120
 Appx 6
121
“suolze}je}sul
paXl} Ul pasn ase sajqed ay} Baym 6 pure g Saige] LEZI Sg O} Sajqed IAd BHuljsisas Jeay D, 06 O} pue
(2)L PIG2L pO09 Sg 0} Sajqed a/q!xa]} 0} ajqerijdde osje ase g 0} Z SUUNIOD UI Sai}19eded HulAsed-JUaIND BYyL
‘xipueddy
SIU} O} UOIPNPOJ}U! BY} as ‘9EOE Sg O} ASN} pasojrua-ias e Aq pa}da}01d aq O} S| JOJINPUOD ay} B19Y/\\
“LLOL SE $9 VLAV PIGeL 92S -
Vat
siqel
dn
ae
sainjessdwa}
0}
Buljyesado
10}9nNpuod
JUIN.
06
D,
ajqeydade
ay}
Huljes
S|
paseaidul
JIU "D. OL Hulpaaoxa jou aunzesadua} e }e UNI YDdIYM Sajqe> YIM a}e1ado 0} paubisap saliossaq7e
JO JUaWAINba 0} payeUUOD sajqed JO} ajqedi|dde ase uO!}eiNsul HulZesOWaY} YIM sajqed oJ sHuljes BY
‘149 HIE VL OL SALON
 “LLOL Sd 40 v XIpueddy aas JUaW}eaJ} JA}/N}
2 104 “AYID1|AWIs 404 pa}!WoO SI ‘8ZIS JOJINpUOD aAoge pue ,WW GZ JO} papiAold Ajjensn dosp aberOA jo JUawaja 9AI}De9J BY] :@JON 4
‘doip a6ei0A sa61e] Ul 3)NSad [IM (D9 ajqe| 0} sajoU das) Z| POU BDUaIJAJayY UI Palji9ads asou} UeY} JabHie; sHuldeds :a}0N x

v
(JJeM e UO JO (Buryono} (J2EM e& UO JO uae
(6ulysno} (10243 Ul) Ul *D}9 JINPUOD ‘sKe1} UO O | Ul D}9 JINPUOD as

aseud-ajbuls
(,pareds 7e}}) pue 3e}}) ZL U! paso|>ua) (xpareds) =| Paulp padd)|>) | ul pasojdua) -SSOJD

aiadweaseyd-aaiy}
ZL POY =| LLB L SPOUISI PS LL ‘L SPOYISIN] 78 € SPOYISII CL POUIPIN, | LLB L SPOUIN] 78 ESPOUIPIN| 2°P | 4039Np
adudIajay aduaIajay aduasajoy adudJaoy adudJajay aduaJajay aouasiajay = |S9/Ge2 Z| -yo>

:aunyesodwa}
abeijoa
:(84}aW
doip
Jad)
Jad
Do.
OL ‘sajqed
‘sajqe>
JOJNPUOD
7€pD"e
Hulzesado ‘de
JO
aLar aiqeL cd9 41gVL

Appx 6
122
 Appx 6
123
JES|ABAO SOJON 99S
‘de aseud de aseud ‘de aseud ‘ye aseud
-aaiyy ‘ajqe> | “2p4o‘re | -aeiy} ‘ajqed | ‘D2 p4ode | -sesy}‘aj]GQe> | “Dp4so‘ve | -9e14} ‘sjqQe> | "Pp JO “2'e
3109-INO} aseyd-ajbuis 9409-INOJ aseyd-ajbuls 94109-INOJ aseyd-ajbuls 9109-INOJ aseyd-a|buls
| 10 xajqe> | ‘ya]qe> e102 | 1 Jo yajqed | ‘yajqed e109 | 140 xa|qQe> | ‘ya/Ge> 910 | | JO x9/Ge> | “~2/Ge2 2109
9409-994} | -OM} | 9109-991} | -OM} | 9109-3914} | -OM} | 9109-391U} | -OM} |
(4le Ba44) EL POUR (Burjunsy ul so
QDUdIBJ9yY 1O ‘Huljlad JO [jem e UO (D}9 “|JeM pezejnsul ease
(Aes} 8]qe) pazesOjjed e uo) (as1p peddi)>) }INPUOD UI paeso|>dUs) ue Ul paso|duUe) jeUOI}DAS-sso1D
LL pou Ls edusiefay | pou sdUsIaJ9y € POUJ2/\| BDUSIBJ9Y py POUJS B2Us19}9y Jo}DNpuoD
6Z9ZL SE ‘7009 Sa :(Sesedwiy) ALIDVdVD ONIAYYVI-LNAYYND
>, OL aunyesadwa} Buljesado J0JNPUOD *D, OE :eun}pesodwWea} Jusiquiy
(SHOLDNGNOD YaddOD) ‘P24noue-uoU ‘(| a}0U) UOHZe]NSU! HUI}}aSOUI9Y} 40 (20d) 2143se}dow4eY} Buiaey sajqe> 2410913/nNWI
Ved 9|GeL 149 F1aVL
 124
Appx 6
SHLON
OL HIEAVL
-TH9

=“ BYL sHulyes
40} SajqerYUM HulyWasOWaY}
uo!}e|Nsu!
ase ajqedi|dde
4104 sajqed pa}aUUOD
0} JUaWAINb~a
JO
saiiossanzepaubisap
0} a}e1ado
YIM Sajqe> YDIYMUNI 7e e aiN}esadW9}
OU Hulpaeadxa
OL D. JOUM
paseasoul si Huljes }UaIIND 9} ajqeydadde ae Dd, YG 0} dn saunjesadwia} Huljzesado 10}9Npuod ye
“LLOL SE 40 VAP PIGe] Ves -

SI

°Z
0}
O}
O}

Sg

9q

ss
Aq
Bas

BY}
BY}
S14}

BSN}
‘QEOE

DIBUN
“Ex YUMJO JNOYUM 9AI}D9}OJd “1OJINPUOD
JE|NIIID $10JINPUOD
a4e pawinsse
10, sazisdn 0} pue Bulpnj>u!
9} ‘pw

pa}da}01d

JOPNPUOD
sanje/A
10} 1a6se]sazis a}ejai
0} padeys siopNpuoOd
pue Aew Ajayesaq patjdde
0} JE|NIIID "SJOPNPUOD

*‘xipueddy
UOIJINPOJ}U!

PasojUa-IWas
TABLE 6E2 Table 4D2B
Voltage drop: Conductor operating
(per ampere per metre): temperature: 70 °C

Conductor Two-core Two-core cable, Three- or four-core

cross-sectional] cable, d.c. single-phase a.c. cable, three-phase
area

Note: The reactive element of voltage drop usually provided for 25 mm?
and above conductor sizes is omitted for simplicity. For a fuller
treatment see Appendix 4 of BS 7671.

125
Appx 6
 TABLE 6F Table 4D5A
70 °C thermoplastic (pvc) insulated and sheathed flat cable
with protective conductor
(COPPER CONDUCTORS)
BS 6004 Table 8
CURRENT-CARRYING CAPACITY Ambient temperature: 30 °C
(amperes): Conductor operating temperature: 70 °C

Installation Installation Reference Voltage drop:

Method 6* Method 15* Method 1 (per ampere
(Enclosed in (Installed (clipped direct) per metre)
Conductor conduit inan | directly in an
cross-sectional insulated wall) | insulated wall)

area 1 two-core cable,

single-phase a.c. or d.c.

(mV/A/m)

1 44
1.5 29

2.5 18
4 11
6 78
10 4.4
2.8

Notes:

1 Where the conductor is to be protected by a semi-enclosed fuse to BS 3036,

see the introduction to this Appendix.
2 * These methods are regarded as Reference Methods for the cable types
specified by the table.

126
Appx 6
 APPENDIX 7 App 6
CERTIFICATION AND REPORTING
The certificates are used with the kind permission of the BSI.

The introduction to Appendix 6 of BS 7671 : 2001 (Model forms for certification and
reporting) is reproduced on this page.

Introduction

(i) The Electrical Installation Certificate required by Part 7 of BS 7671 shall be made out
and signed or otherwise authenticated by a competent persons or persons in respect
of the design, construction, inspection and testing of the work.
(ii) | The Minor Works Certificate required by Part 7 of BS 7671 shall be made out and
signed or otherwise authenticated by a competent person in respect of the
inspection and testing of an installation.
(iii) |The Periodic Inspection Report required by Part 7 of BS 7671 shall be made out and
signed or otherwise authenticated by a competent persons in respect of the
inspection and testing of an installation.
(iv) Competent persons will, as appropriate to their function under (i) (ii) and (iii) above,
have a sound knowledge and experience relevant to the nature of the work
undertaken and to the technical standards set down in this British Standard, be fully
versed in the inspection and testing procedures contained in this Standard and
employ adequate testing equipment.
(v) Electrical Installation Certificates will indicate the responsibility for design,
construction, inspection and testing, whether in relation to new work or further
work on an existing installation.
Where design, construction and inspection and testing is the responsibility of one person a
Certificate with a single signature declaration in the form shown below may replace the
multiple signatures section of the model form.
FOR DESIGN, CONSTRUCTION, INSPECTION & TESTING.
| being the person responsible for the Design, Construction, Inspection & Testing
of the electrical installation (as indicated by my signature below), particulars of
which are described above, having exercised reasonable skill and care when
carrying out the Design, Construction, Inspection & Testing, hereby CERTIFY that
the said work for which | have been responsible is to the best of my knowledge
and belief in accordance with BS 7671: ............ , amended to ...........+ (date)
except for the departures, if any, detailed as follows.
(vi) A Minor Works Certificate will indicate the responsibility for design, construction,
inspection and testing of the work described in Part 4 of the certificate.
(vii) A Periodic Inspection Report will indicate the responsibility for the inspection and
testing of an installation within the extent and limitations specified on the form
report.
(viii) A Schedule of Inspections and a Schedule of Test Results as required by Part 7 shall be
issued with the associated Electrical Installation Certificate or Periodic Inspection Report.
(ix) When making out and signing a form on behalf of a company or other business
entity, individuals shall state for whom they are acting.
(x) | Additional forms may be required as clarification, if needed by non-technical
persons, or in expansion, for larger or more complex installations.
on
(xi) The IEE Guidance Note 3 provides further information on inspection and testing
completion and for periodic inspections.

127
Appx 7
ELECTRICAL INSTALLATION CERTIFICATES
NOTES FOR SHORT FORM F1 AND STANDARD FORM F2:

The Electrical Installation Certificate is to be used only for the initial

certification of a new installation or for an alteration or addition to an
existing installation where new circuits have been introduced.
It is not to be used for a Periodic Inspection for which a Periodic
Inspection Report form should be used. For an alteration or addition
which does not extend to the introduction of new circuits, a Minor
Electrical Installation Works Certificate may be used.
The original Certificate is to be given to the person ordering the work
(Regulation 742-01-03). A duplicate should be retained by the
contractor.

This Certificate is only valid if accompanied by the Schedule of

Inspections and the Schedule(s) of Test Results.
The signatures appended are those of the persons authorised by the
companies executing the work of design, construction and inspection
and testing respectively. A signatory authorised to certify more than
one category of work should sign in each of the appropriate places.
The time interval recommended before the first periodic inspection
must be inserted (see IEE Guidance Note 3 for guidance).

The page numbers for each of the Schedules of Test Results should be
indicated, together with the total number of sheets involved.
The maximum prospective fault current recorded should be the greater
of either the short-circuit current or the earth fault current.
The proposed date for the next inspection should take into
consideration the frequency and quality of maintenance that the
installation can reasonably be expected to receive during its intended
life, and the period should be agreed between the designer, installer
and other relevant parties.

128
Appx 7
Form Fl Form No 123/1
ELECTRICAL INSTALLATION CERTIFICATE (notes 1 and 2)
(REQUIREMENTS FOR ELECTRICAL INSTALLATIONS - BS 7671 [IEE WIRING REGULATIONS])

Postcode AB] 2CD

DESCRIPTION AND EXTENT OF THE INSTALLATION Tick boxes as appropriate
D : New installation
Description of installation: lomestic

Extent of installation covered by this Certificate: Addition to an

existing installation
Complete electrical, including
smoke andintruder alarms
Alteration to an
existing installation
Use continuation sheet if necessary) see continuation sheet No: ........
FOR DESIGN, CONSTRUCTION, INSPECTION & TESTING
| being the person responsible for the Design, Construction, Inspection & Testing of the electrical installation (as indicated by my
signature below), particulars of which are described above, having exercised reasonable skill and care when carrying out the Design,
Construction, Inspection & Testing, hereby CERTIFY that the said work for which | have been responsible is to the best of my knowledge
and belief in accordance with BS 7671: .20Q1.., amended to ..2004... (date) except for the departures, if any, detailed as follows:

Details of departures from BS 7671 (Regulations 120-01-03, 120-02):

None

The extent of liability of the signatory is limited to the work described above as the subject of this Certificate.

Name (IN BLOCK LETTERS).... Position: ...pane

DMTOCLOT.....ccssecccceeese0
Signature (note 3):. Date riences VA ersten
nc
For and on behalf 0
Address:

: (Cotttttiin one Postcode...E.B.4GH. TalNoster ete are ar eee

=|
a INSPECTION
4 and 7)
| recommend that this installation is further inspected and tested after an interval of not more than AQ....... years/mronens. (notes
SUPPLY CHARACTERISTICS AND EARTHING ARRANGEMENTS SeKboves aucieiiey celal aeteppontela
Number and Type of Live Nature of Supply Parameters Supply
Earthing arrangements
g Conductors Protective Device
TN-C Characteristics
TN-S O a.c. wx d.c. O Nominal voltage, U/US" ...
wa Type: BS 1361
TN-C-S uw
TT L] | 1-phase, 2-wire 2-pole C1 | Nominal frequency, fs 50... Hz fuse
O .6...kA
iB 1-phase, 3-wire O 3pole O Prospective fault current, ly Nominal current rating
note 6)
Alternative source oO 2-phase, 3-wire CO other O (
of supply (to be detailed
External loop impedance,
Z, 20.350
on attached schedules) 3-phase, 3-wire Oo Re a
oO (Note: (1) by enquiry, (2) by enquiry or by measurement)
3-phase, 4-wire
Page | of 4 (note 5)

129
Appx 7
 PARTICULARS OF INSTALLATION REFERRED TO IN THE CERTIFICATE '* Boxesjand ertor oetate 25 Peo
Means of Earthing Maximum Demand

Distributor’s facility uy Maximum demand (load) .............:0.. 60. Amps per phase

Details of Installation Earth Electrode (where applicable)

Installation Type Location Electrode resistance to earth
earth electrode O (e.g. rod(s), tape etc)
ee Note aan ee ee ee

Earthing conductor: material --- Copper eae CSA) oo... f Gr mm2 connection verified My

Main equipotential bonding

conductors material ......Capper. ae csaee A0........mm? connection verified wy

To incoming water and/or gas service wy MO OtMSriGlOMENUS! aes -cescecccsvescoctscevursaceacecsestuccseccsusseusvsceensseuanrerves

Main Switch or Circuit-breaker

BS, Type
yl BS EN 60439-3 No. of poles oie Current rating ........ S0...A Voltage rating ......230...V

Location . GATage PEE etescaveat Cosersorewosrarennivonesueet Fuse rating or setting... A

(applicable only where an RCD issuitable and is used as a main circuit-breaker)
Rated residual operating current lan = 3... mA, andoperating time of 200 ms (at lan
COMMENTS ON EXISTING INSTALLATION (in the case of an alteration or additions see Section 743):

SCHEDULES (note 2)
The attached Schedules are part of this document and this Certificate is valid only when they are attached to it.
ie ecu Schedule(s) of Inspections and ......... Schedule(s) of Test Results are attached.
(Enter quantities of schedules attached).

Page 2 of 4 (note 5)

GUIDANCE FOR RECIPIENTS

This safety Certificate has been issued to confirm that the electrical installation work to which it relates has been designed,
constructed and inspected and tested in accordance with British Standard 7671 (the IEE Wiring Regulations).

You should have received an original Certificate and the contractor should have retained a duplicate Certificate. If you were the
person ordering the work, but not the user of the installation, you should pass this Certificate, or a full copy of it including the
schedules, immediately to the user.

The "original" Certificate should be retained in a safe place and be shown to any person inspecting or undertaking further work
on the electrical installation in the future. If you later vacate the property, this Certificate will demonstrate to the new owner that
the electrical installation complied with the requirements of British Standard 7671 at the time the Certificate was issued. The
Construction (Design and Management) Regulations require that for a project covered by those Regulations, a copy of this
Certificate, together with schedules is included in the project health and safety documentation.

For safety reasons, the electrical installation will need to be inspected at appropriate intervals by a competent person. The
maximum time interval recommended before the next inspection is stated on Page 1 under "Next Inspection”.

This Certificate is intended to be issued only for a new electrical installation or for new work associated with an alteration or
addition to an existing installation. It should not have been issued for the inspection of an existing electrical installation. A
"Periodic Inspection Report" should be issued for such a periodic inspection.

The Certificate is only valid if a Schedule of Inspections and a Schedule of Test Results is appended.

130
Appx 7
 Form F3 Form No123 /3
SCHEDULE OF INSPECTIONS
Methods of protection against electric shock Prevention of mutual detrimental influence

(a) Protection against both direct and indirect (a) Proximity of non-electrical services and other influences
contact: (b) Segregation of band I and band II circuits or band II

N
insulation used
(i) SELV (note 1)
WZal (ii) Limitation of discharge of energy
(c) Segregation of safety circuits

(b) Protection against direct contact: (note 2)

Identification
(a) Presence of diagrams, instructions, circuit charts and
(i) Insulation of live parts
similar information
(ii) Barriers or enclosures
(b) Presence of danger notices and other warning notices
(iii) Obstacles (note 3)

NNNN
(c) Labelling of protective devices, switches and terminals
(iv) Placing out of reach (note 4)
(d) Identification of conductors

NSSISINS
(Vv) PEEV:
Cables and conductors
(vi) Presence of RCD for supplementary
protection = Routing of cables in prescribed zones or within
mechanical protection
(c) Protection against indirect contact:
S Connection of conductors
(i) | EEBAD including: Erection methods
Presence of earthing conductor
CO Selection of conductors for current-carrying capacity and

AN
NAN
N
Presence of circuit protective conductors voltage drop

Presence of main equipotential bonding (e) Presence of fire barriers, suitable seals and protection
conductors against thermal effects

Presence of supplementary equipotential General

Bl
NINN
N
bonding conductors
(a) Presence and correct location of appropriate devices for
Presence of earthing arrangements for isolation and switching
combined protective and functional
(b) Adequacy of access to switchgear and other equipment
purposes
\ (c) Particular protective measures for special installations
eS Presence of adequate arrangements for
and locations
alternative source(s), where applicable
(d) Connection of single-pole devices for protection or
Presence of residual current device(s)
switching in phase conductors only
L (il) | Use of Class I! equipment or equivalent
(e) Correct connection of accessories and equipment
insulation (note 5)
(f) | Presence of undervoltage protective devices
hal (iii) Non-conducting location: (note 6)
Absence of protective conductors (g) Choice and setting of protective and monitoring devices
for protection against indirect contact and/or overcurrent
(iv) Earth-free equipotential bonding: (note 7)
Presence of earth-free equipotential (h) Selection of equipment and protective measures

AN
AN
N
NsIN
NN
bonding conductors appropriate to external influences

\ (v) Electrical separation (note 8) (i) Selection of appropriate functional switching devices

Inspected by tt. Surith Seo ins iS pate ....20/4/2004 |

Notes:
v to indicate an inspection has been carried out and the result is satisfactory
x to indicate an inspection has been carried out and the result was unsatisfactory
N/A to indicate the inspection is not applicable
LIM to indicate that, exceptionally, a limitation agreed with the person ordering the work prevented the inspection or test
being carried out.
SELV An extra-low voltage system which is electrically 5: Use of Class II equipment - infrequently adopted and only
separate from earth and from other systems. The when the installation is to be supervised
particular requirements of the Regulations must be (see Regulations 413-03 and 471-09)
checked (see Regulations 411-02 and 471-02) Non-conducting locations - not applicable in domestic
Method of protection against direct contact - will include 7a premises and requiring special precautions
measurement of distances where appropriate (see Regulations 413-04 and 471-10)
Obstacles - only adopted in special circumstances Earth-free local equipotential bonding - not applicable in
(see Regulations 412-04 and 471-06) domestic premises, only used in special circumstances
(see Regulations 413-05 and 471-14)
Placing out of reach - only adopted in special
circumstances (see Regulations 412-05 and 471-07) Electrical separation (see Regulations 413-06 and 471-12)

Page 3 of 4

131
Appx 7
 O ,o5R,
paopeoe d 5]|NsaJ 4S9} $O BjNPays UO $a}0U Bas x

aud
:sejou jeloeds pue suonejnBey Burs wos suoiyeineq
iz eee aaa ses
| aes [ome ae Bou: 5
GL L|_ 00% | #0F p| 0 — 7 ; 2 D
50 as: Ov — fm fi D 4amoys
IMoHITL SE 00c
Os i a f D 4ayooD
Yi 50 Ta OF
y
‘GM Vu 00c 60 - O€ — €0 i ‘ i D umop s7ayI0S
Agua,
ee HO) Cm Oa ea. #0 GATOS, ae G dn s1ayo0S
Lou, f,i= De ZS Oca as = Lies Orbe \isar or & unop sy
A es nO: os = = re Gitano or D dn syybiT
tL ar ra 1 re 6» gx | Lx 9% S v € z 1
St OW | 6 Oo Oo gui | 7Wwu Vv
sui oO AK OW
+ u
awl} ! yyeqz | any \ 4
4ayuyO | Gdy SZ i Jeary | aan uy zy} @y+ ty od> any | Burney | adAy
aoue e
Busey -paduu} | a2ueysisay s40}NpuoD wg
syseway jeuonoun4 dooq ° uolje|nsu| AyinuryuoD Buin :Ayoedes
yyeq ‘al PINDIID-OYS , uoljdidsag WNUID
a0lneq
syjnsay JsoL JUALINDBAO,
Jif; PHON\ 40 uonduoseq
seseereerereneseeseneeaeeenenneriyig tit ous 14 mdi jiassaiont pin TaIuIp F pub 7 syina1is SIG Kil OE Buse} 0} ajqesoujna juewdinbS
‘i 98]U09 JOAJIPU! JsuLeBe UONDa}Od jo poay
‘Cope 40180 GO" wy aunyeuBbis
ee ore uoleinsul
pee oe :Aynuluod suo ep cituoye 97, BP: Ss Y
e0uepeduut doo} eb/S-O-NL/Sehit Adding jo edAl , FOOT t/0d 2a sel
TIDE
S]UaUINASU] aaa 0 Sua ie 110}0B4JU0D,
SLINSAY LS3L AO AINGAHIS
v/ exp ON WHOA p WLIO4

Appx 7
132
NOTES ON SCHEDULE OF TEST RESULTS
* Type of supply is ascertained from the distributor or by inspection.
* Ze at origin. When the maximum value declared by the distributor is used, the effectiveness of the earth must be confirmed by a
test. If measured the main bonding will need to be disconnected for the duration of the test.

* Short-circuit capacity of the device is noted, see Table 7.2A of the On-Site Guide or 2.7.15 of GN3
* Prospective fault current (PFC). The value recorded is the greater of either the short-circuit current or the earth fault current.
Preferably determined by enquiry of the distributor.
The following tests, where relevant, shall be carried out in the following sequence:

Continuity of protective conductors, including main and supplementary bonding

Every protective conductor, including main and supplementary bonding conductors, should be tested to verify that they are continuous
and correctly connected.

*6 Continuity
Where Test Method 1 is used, enter the measured resistance of the phase conductor plus the circuit protective conductor (R1+ R2).
See 10.3.1 of the On-Site Guide or 2.7.5 of GN3.
During the continuity testing (Test Method 1) the following polarity checks are to be carried out:
(a) every fuse and single-pole control and protective device is connected in the phase conductor only
(b) centre-contact bayonet and Edison screw lampholders have outer contact connected to the neutral conductor
(.) _ wiring is correctly connected to socket-outlets and similar accessories.
Compliance is to be indicated by a tick in polarity column 11.

(R1 + R2) need not be recorded if R2 is recorded in column 7.

*7 Where Test Method 2 is used, the maximum value of R2 is recorded in column 7.

Where the alternative method of Regulation 413-02-12 is used for shock protection, the resistance of the circuit
protective conductor R2 is measured and recorded in column 7.
See 10.3.1 of the On-Site Guide or 2.7.5 of GN3.

*8 Continuity of ring final conductors

A test shall be made to verify the continuity of each conductor including the protective conductor of every ring final circuit.
See 10.3.2 of the On-Site Guide or 2.7.6 of GN3.
*9,*10 Insulation Resistance
All voltage sensitive devices to be disconnected or test between live conductors (phase and neutral) connected together and earth.
The insulation resistance between live conductors is to be inserted in column 9.
The minimum insulation resistance values are given in Table 10.1 of the On-Site Guide or Table 2.2 of GN3.
See 10.3.3(iv) of the On-Site Guide or 2.7.7 of GN3.

All the preceding tests should be carried out before the installation is energised.
*11 Polarity
A satisfactory polarity test may be indicated bya tick in column 11.
polarity.
Only in a Schedule of Test Results associated with a Periodic Inspection Report is it acceptable to record incorrect
*12 Earth fault loop impedance Zs
column 6 to
This may be determined either by direct measurement at the furthest point of a live circuit or by adding (Ri + R2) of
used.
Ze. Ze is determined by measurement at the origin of the installation or preferably the value declared by the distributor
or App 2 of GN3.
Z, = Ze + (R1 + R2). Zs should be less than the values given in Appendix 2 of the On-Site Guide
*13 Functional testing
in the device.
The operation of RCDs (including RCBOs) shall be tested by simulating a fault condition, independent of any test facility
Record operating time in column 13. Effectiveness of the test button must be confirmed.
See Section 11 of the On-Site Guide or 2.7.16 of GN3.
that they are properly
*14 All switchgear and controlgear assemblies, drives, control and interlocks, etc must be operated to ensure
mounted, adjusted, and installed.
Satisfactory operation is indicated bya tick in column 14.
;
Earth electrode resistance
required.
The earth electrode resistance of TT installations must be measured, and normally an RCD is
value on Forms 1, 2 or 6 as
For reliability in service the resistance of any earth electrode should be below 200 2. Record the
appropriate. See 10.3.5 of the On-Site Guide or 2.7.13 of GN3.

133
Appx 7
 Form F 2 Form No124 /2
ELECTRICAL INSTALLATION CERTIFICATE (notes 1 and 2)
(REQUIREMENTS FOR ELECTRICAL INSTALLATIONS - BS 7671 [IEE WIRING REGULATIONS])
DETAILS OF THE CLIENT (note1) 7 /,,,
dev loper Ltd.
ei

INSTALLATION ADDRESS

DESCRIPTION AND EXTENT OF THE INSTALLATION Tick boxes as appropriate

(note 1) 7 : - New installation

Description of installation:
Warehouse/factory with
Extent of installation covered by this Ce: Addition to an
existing installation

Alteration to an
existing installation

FOR DESIGN
of which are described
\We being the person(s) responsible for the design of the electrical installation (as indicated by my/our signatures below), particulars
have been responsible is to
above, having exercised reasonable skill and care when carrying out the design hereby CERTIFY that the design work for which I/we
the best of my/our knowledge and belief in accordance with BS 7671 : 4 .., amended to. 201 (date) except for the departures, if any, detailed
as follows:

Details of departures from BS 7671 (Regulations 120-01-03, 120-02):

None

The extent of liability of the signatory or the signatories is limited to the work described above as the subject of this Certificate.

For the DESIGN oftheinstallation: **(Where there is mutual responsibility for the design)
C Me
Signature: ...S OU pate.2/4/2004 Name (BLOCK LETTERS): ......../ B BR . Designer No 1

Signature:.. Name (BLOCK LETTERS): ....-.-..:.csc00 Designer No 2°*

FOR CONSTRUCTION
are de-
We being the person(s) responsible for the construction of the electrical installation (as indicated by my/our signatures below), particulars of which
scribed above, having exercised reasonable skill and care when carrying out the construction her CERTIFY that theconsitugion work for which I/we have
responsible is to the best of my/our knowledge and belief in accordance with BS 7671: amended to (date) except for the
been
departures, if any, detailed as follows:

Details of departures from BS 7671 (Regulations 120-01-03, 120-02):

. None
The extent of liability of the signatory is limited to the work described above as the subject of this Certificate.

W White 6/4/2004
For CONSTRUCTION ofthe installation:

Signature... -0...c.2
2 Date.....

Name (BLOCK LETTERS): NTe W

A anes WHIT:
occas cousecotewesseagateceaoscaxenanouchvereseesbsrasn¥acus enesemmececrestanfSiasusdssvireyaaaesenesasiine Constructor
FOR INSPECTION & TESTING
\We being the person(s) responsible for the inspection & testing of the electrical installation (as indicated by my/our signatures below), particulars of which
are described above, having exercised reasonable skill and care when carrying out the inspection & Js5hn9 hereby CERTIFY that he,work for which I/we
have been responsible is to the best of my/our knowledge and belief in accordance with BS 767 Alainteurenars , AMENdEM tO «.....se.eee 2004 (date) except for the
departures, if any, detailed as follows:

Details
of departures from BS 7671 (Regulations 120-01-03, 120-02):
None

The extent of liability of the signatory is limited to the work described above as the subject of this Certificate.
For INSPECTION AND TEST of the installation:
Signature:..
Name (BLOCK LETTERS): .
NEXT INSPECTION (notes 4 and 7) 3
\We the designer(s), recommend that this installation is further inspected and tested after an interval of not more than years/inions.

Page | of 4

134
Appx 7
PARTICULARS OF SIGNATORIES TO THE ELECTRICAL INSTALLATION CERTIFICATE
Designer (No 1)
Name: BBrown. t Company:
AddressC )
ee County...
Designer (No 2)
(if applicable)

. Postcode:
Constructor
Company: ...

. Postcode:
Inspector
Name: eS Company:

. Postcode:
SUPPLY CHARACTERISTICS AND EARTHING ARRANGEMENTS (~<0%°° 20 onler detail, a5 sppropral
Earthing arrangements Number and Type of Live Nature of Supply Parameters Supply
Conductors Protective Device
TN-C O ro ae Characteristics
TN-S oO ae; dc. (© | Nominal voltage, U/Us"” 400230V ee
TN-C-S cg eC] Type: BS 1361
tt oO 1-phase, 2-wire 2-pole(1]_ | Nominal frequency, f ........-..- 30 uz Fuse
IT ; (note 6) ’
O 1-phase, 3-wireL] 3-pole F] Nominal current
‘ source O
Alternative 2-phase, 3-wireL] other 1 Prospective
Pp fault current, pf
lpr ..£9 ka ting ...L00...A
rating
of supply (to be detailed 0.2
on attached schedules) | 3.phase, 3-wire L] External loop impedance, Ze 0/5.
A (Note: (1) by enquiry, (2) by enquiry or bymeasurement)
3-phase, 4-wire
PARTICULARS OF INSTALLATION REFERRED TO IN THE CERTIFICATE “00s S77ene"SIs. @8 appropriate
Means of Earthing Maximum Demand
pe b a me - 40
Distributor’s facility Maximum demand (load) .....-....-.sesseeneo Amps per phase
Details of Installation Earth Electrode (where applicable)
Installation oO Type Location Electrode resistance to earth
earth electrode e.g. rod(s), tape
ae
etc
— DE ae Thet ns

Earthing conductor: material ...

Main equipotential bonding

conductors material ... Dppe 68a ative: LOLs mm? connection verified

x To other Clement: .........-.-ss.s-cecesseseceesenesesrsnsseseceesscsesesssecsneeseenes =

To incoming water and/or gas service
Main Switch or Circuit-breaker

No. of poles no Current rating ....... 125.4 Voltage rating pe OU any

BS, Type

Location .. S71tchroam..adjacent.main.office. Fuse rating or setting.....as0.....A

current lan = Pe /aeiiAv and operatina ur

mete eee
tial ot earns (ext hi. erre cece
Rated residual operating
Section 743):
COMMENTS ON EXISTING INSTALLATION (in the case of an alteration or additions see
Not-applicabte.

SCHEDULES (note 2)
when they are attached to it.
The attached Schedules are part of this document and this Certificate is valid only
sattnelace Schedule(s) of Inspections and ...-L...... Schedule(s) of Test Results are attached.
(Enter quantities of sct Ss attached).
alae le

Page 2 of 4

135
Appx 7
ELECTRICAL INSTALLATION CERTIFICATE
GUIDANCE FOR RECIPIENTS (to be appended to the Certificate)

This safety Certificate has been issued to confirm that the electrical installation
work to which it relates has been designed, constructed and inspected and tested
in accordance with British Standard 7671 (the IEE Wiring Regulations).

You should have received an original Certificate and the contractor should have
retained a duplicate Certificate. If you were the person ordering the work, but
not the user of the installation, you should pass this Certificate, or a full copy of
it including the schedules, immediately to the user.

The "original" Certificate should be retained in a safe place and be shown to any
person inspecting or undertaking further work on the electrical installation in
the future. If you later vacate the property, this Certificate will demonstrate to
the new owner that the electrical installation complied with the requirements of
British Standard 7671 at the time the Certificate was issued. The Construction
(Design and Management) Regulations require that for a project covered by
those Regulations, a copy of this Certificate, together with schedules is included
in the project health and safety documentation.

For safety reasons, the electrical installation will need to be inspected at

appropriate intervals by a competent person. The maximum time interval
recommended before the next inspection is stated on Page 1 under "Next
Inspection".

This Certificate is intended to be issued only for a new electrical installation or

for new work associated with an alteration or addition to an existing installation.
It should not have been issued for the inspection of an existing electrical
installation. A "Periodic Inspection Report" should be issued for such a periodic
inspection.

The Certificate is only valid if a Schedule of Inspections and a Schedule of Test Results
is appended .

136
Appx 7
 Form F3 Form No 124/3
SCHEDULE OF INSPECTIONS
Methods of protection against electric shock Prevention of mutual detrimental influence

(a) Protection against both direct and indirect [Vv] (a) Proximity of non-electrical services and other influences
contact: v ] (b) Segregation of band I and band II circuits or band II
insulation used
[NZA (i) SELV (note 1)
Vv (c) Segregation of safety circuits
(ii) Limitation of discharge of energy
Identification
(b) Protection against direct contact: (note 2)
[Vv] (a) Presence of diagrams, instructions, circuit charts and
v1 (i) Insulation of live parts similar information
Vv] (ii) | Barriers or enclosures [Vv (b) Presence of danger notices and other warming notices
[NZA| (iii) Obstacles (note 3) Vv (c) Labelling of protective devices, switches and terminals
A (iv) Placing out of reach (note 4) Vv ] (d) Identification of conductors
(v) PELV Cables and conductors
(vi) Presence of RCD for supplementary
protection Vv ] (a) Routing of cables in prescribed zones or within
mechanical protection
(c) Protection against indirect contact:
Vv (b) Connection of conductors
(i) | EEBAD including: (c) Erection methods
Presence of earthing conductor Vv] (d) Selection of conductors for current-carrying capacity and
Presence of circuit protective conductors voltage drop

Presence of main equipotential bonding (e) Presence of fire barriers, suitable seals and protection
conductors against thermal effects
Presence of supplementary equipotential General

SSS
SN
E
bonding conductors (a) Presence and correct location of appropriate devices for
Presence of earthing arrangements for isolation and switching
combined protective and functional
(b) Adequacy of access to switchgear and other equipment
purposes
(c) Particular protective measures for special installations
Presence of adequate arrangements for
and locations
alternative source(s), where applicable
(d) Connection of single-pole devices for protection or

&
EE
Presence of residual current device(s)
switching in phase conductors only
(ii) Use of Class Il equipment or equivalent
(e) Correct connection of accessories and equipment
insulation (note 5)
(f) |Presence of undervoltage protective devices
(iii) |Non-conducting location: (note 6)
Absence of protective conductors (g) Choice and setting of protective and monitoring devices
for protection against indirect contact and/or overcurrent
(iv) Earth-free equipotential bonding: (note 7)
Presence of earth-free equipotential (h) Selection of equipment and protective measures

S
SSIS
RSS
NS
bonding conductors appropriate to external influences

(v) Electrical separation (note 8) (i) Selection of appropriate functional switching devices
10/4/2004
Inspected by Snes ceca caotldepicese

Notes:
Y toindicate an inspection has been carried out and the result is satisfactory
X to indicate an inspection has been carried out and the result was unsatisfactory
N/A _ to indicate the inspection is not applicable
the work prevented the inspection or test
LIM _ to indicate that, exceptionally, a limitation agreed with the person ordering
being carried out.
5. Use of Class II equipment - infrequently adopted and only
as SELV An extra-low voltage system which is electrically
when the installation is to be supervised
separate from earth and from other systems. The
particular requirements of the Regulations must be (see Regulations 413-03 and 471-09)
checked (see Regulations 411-02 and 471-02) 6. Non-conducting locations - not applicable in domestic
premises and requiring special precautions
2. Method of protection against direct contact - will include
measurement of distances where appropriate (see Regulations 413-04 and 471-10)
te Earth-free local equipotential bonding - not applicable in
3. Obstacles - only adopted in special circumstances domestic premises, only used in special circumstances
(see Regulations 412-04 and 471-06)
(see Regulations 413-05 and 471-14)
4, Placing out of reach - only adopted in special
8. Electrical separation (see Regulations 413-06 and 471-12)
circumstances (see Regulations 412-05 and 471-07)
Page 3 of 4

137
Appx 7
f JOp ase S}]NSBJ }S9} JO B/NPEs UO SB}OU 99S x
aUuONG
:sajou jejoeds pue suojejnbey Buys wos suojjeiAaeq
agony,
yueg | aay
SHIeW3Y jean | jean any | Buney
92ue
Buljsal -padwy a2uP}sIisoy ss0}Npuoy
uoljze|nsu| Ayinuiuo> Budi :Aywedes

JUBNDIBAOC
Jeuonpuny doo
yueq pindsid-WWo0Yys , uoldis9sag WNUID
a01Aeq
s}|NsoyY Jsol]
ase ceeeecenscceseacccesesccsenes . ep UD Pi “sHopaliy, OM JO uonduoseq
Ess eeeecae cee seoreaty anaes
anova sea np reenereanasskeocgtaz cent rnc aa ITD wey aa TIO LTO Sepp OS Oona Ltn EAT aT :Bunjse} 0} a|qeseujnn juawidinb3
Dk :48188} GOY “OU DD Dr Oe \u0o yoo pu! ysurebe uoyjoajo1d jo pouyeyy
Vi Sunes
~ gunyeuBis
Dis suoweinsut
no :Aynulyuoo swyo' ‘(7 :ulBUO ye 87 ,
sgouepedw! doo} —~—tL/S-O-NLG-NL :Alddngs jo adfy , emeoremseneree HOQC/H/OT :818C SOL
Sjueunysuy jg. I RSOSHORREHISIB-FO-HEHESOT/SSOIPPY PVT SIIDNUOY IAT, 40\eUOD,
S11NSAY LSAL JO FINGSHDS
p WO
b/PeT ON UO{

Appx 7
138
NOTES ON SCHEDULE OF TEST RESULTS
* Type of supply is ascertained from the distributor or by inspection.
* Ze at origin. When the maximum value declared by the distributor is used, the effectiveness of the earth must be confirmed by a
test. If measured the main bonding will need to be disconnected for the duration of the test.

* Short-circuit capacity of the device is noted, see Table 7.2A of the On-Site Guide or 2.7.15 of GN3

* Prospective fault current (PFC). The value recorded is the greater of either the short-circuit current or the earth fault current.
Preferably determined by enquiry of the distributor.
The following tests, where relevant, shall be carried out in the following sequence:

Continuity of protective conductors, including main and supplementary bonding

Every protective conductor, including main and supplementary bonding conductors, should be tested to verify that they are continuous
and correctly connected.

*6 Continuity
Where Test Method 1 is used, enter the measured resistance of the phase conductor plus the circuit protective conductor (R4+ R2).
See 10.3.1 of the On-Site Guide or 2.7.5 of GN3.
During the continuity testing (Test Method 1) the following polarity checks are to be carried out:
(a) every fuse and single-pole control and protective device is connected in the phase conductor only
(b) centre-contact bayonet and Edison screw lampholders have outer contact connected to the neutral conductor
(a) wiring is correctly connected to socket-outlets and similar accessories.
Compliance is to be indicated by a tick in polarity column 11.

(Rj + R2) need not be recorded if R2 is recorded in column 7.

*7 Where Test Method 2 is used, the maximum value of R2 is recorded in column 7.

Where the alternative method of Regulation 413-02-12 is used for shock protection, the resistance of the circuit
protective conductor R2 is measured and recorded in column 7.
See 10.3.1 of the On-Site Guide or 2.7.5 of GN3.

*8 Continuity of ring final conductors

A test shall be made to verify the continuity of each conductor including the protective conductor of every ring final circuit.
See 10.3.2 of the On-Site Guide or 2.7.6 of GN3.

*9,*10 Insulation Resistance

All voltage sensitive devices to be disconnected or test between live conductors (phase and neutral) connected together and earth.
The insulation resistance between live conductors is to be inserted in column 9.
The minimum insulation resistance values are given in Table 10.1 of the On-Site Guide or Table 2.2 of GN3.
See 10.3.3(iv) of the On-Site Guide or 2.7.7 of GN3.

All the preceding tests should be carried out before the installation is energised.
*11 Polarity
A satisfactory polarity test may be indicated bya tick in column 11.
incorrect polarity.
Only in a Schedule of Test Results associated with a Periodic Inspection Report is it acceptable to record
*12 Earth fault loop impedance Zs
+ R2) of column 6 to
This may be determined either by direct measurement at the furthest point of a live circuit or by adding (Ri
the distributor used.
Ze. Ze is determined by measurement at the origin of the installation or preferably the value declared by
in Appendix 2 of the On-Site Guide or App 2 of GN3.
Z; = Ze + (R1 + R2). Zs should be less than the values given
*13 Functional testing
of any test facility in the device.
The operation of RCDs (including RCBOs) shall be tested by simulating a fault condition, independent
Record operating time in column 13. Effectiveness of the test button must be confirmed.
See Section 11 of the On-Site Guide or 2.7.16 of GN3.
to ensure that they are properly
*14 All switchgear and controlgear assemblies, drives, control and interlocks, etc must be operated
mounted, adjusted, and installed.
Satisfactory operation is indicated by a tick in column 14.
Earth electrode resistance
RCD is required.
The earth electrode resistance of TT installations must be measured, and normally an
value on Forms 1, 2 or 6 as
For reliability in service the resistance of any earth electrode should be below 200 Q. Record the
appropriate. See 10.3.5 of the On-Site Guide or 2.7.13 of GN3.

139
Appx 7
 NOTES ON COMPLETION OF MINOR ELECTRICAL INSTALLATION WORKS
CERTIFICATE

Scope

The Minor Works Certificate is intended to be used for additions and alterations to an
installation that do not extend to the provision of a new circuit. Examples include the addition
of a socket-outlet or lighting point to an existing circuit, the relocation of a light switch etc.
This Certificate may also be used for the replacement of equipment such as accessories or
luminaires, but not for the replacement of distribution boards or similar items. Appropriate
inspection and testing, however, should always be carried out irrespective of the extent of the
work undertaken.

Part 1 Description of minor works

1,2 The minor works must be so described that the work that is the subject of the certification
can be readily identified.

4 See Regulations 120-01-03 and 120-02. No departures are to be expected except in most
unusual circumstances. See also Regulation 743-01-03.

Part 2 Installation details

2 The method of protection against indirect contact shock must be clearly identified e.g.
earthed equipotential bonding and automatic disconnection of supply using fuse/circuit
breaker/RCD

4 If the existing installation lacks either an effective means of earthing or adequate main
equipotential bonding conductors, this must be clearly stated. See Regulation 743-01-02.

Recorded departures from BS 7671 may constitute non-compliance with the Electricity
Supply Regulations 1988 as amended or the Electricity at Work Regulations 1989. It is
important that the client is advised immediately in writing.

Part 3 Essential Tests

The relevant provisions of Part 7 (Inspection and Testing) of the BS 7671 must be applied in full
to all minor works. For example where a socket-outlet is added to an existing circuit it is
necessary to:
1 establish that the earthing contact of the socket-outlet is connected to the main earthing
terminal
2 measure the insulation resistance of the circuit that has been added to, and establish that
it complies with Table 71A of BS 7671
3 measure the earth fault impedance to establish that the maximum permitted
disconnection time is not exceeded
4 check that the polarity of e.g. the socket-outlet, is correct
5 (if the work is protected by an RCD) verify the effectiveness of the RCD.

Part 4 Declaration

1,3 The Certificate shall be made out and signed by a competent person in respect of the
design, construction, inspection and testing of the work.

1,3. The competent person will have a sound knowledge and experience relevant to the
nature of the installation undertaken and to the technical standards set down in BS 7671,
be fully versed in the inspection and testing procedures contained in the Regulations and
employ adequate testing equipment.

2 When making out and signing a form on behalf of a company other business entity,
individuals shall state for whom they are acting.

140
Appx 7
Form 5 Form No ..125./5
MINOR ELECTRICAL INSTALLATION WORKS CERTIFICATE
(REQUIREMENTS FOR ELECTRICAL INSTALLATIONS - BS 7671 [IEE WIRING REGULATIONS])
To be used only for minor electrical work which does not include the provision of a new circuit

PART 1 : Description of minor works

. Description of the minor works :

. Location/Address :

. Date minor works completed :

. Details of departures, if any, from BS 7671

‘Gr

PART 2: Installation details

. System earthing arrangement TN-C-S [TY INST

. Method of protection against indirect contact: ee BA Ds

. Protective device for the modified circuit : Type BS ...-

. Comments on existing installation, including adequacy of earthing and bonding arrangements : (See Regulation 130-07)

PART 3 : Essential Tests

1 Earth continuity : satisfactory

me Insulation resistance:
Phase/neutral

Phase/earth

Neutral/earth

. Earth fault loop impedance ............... OS ps Q

. Polarity : satisfactory re

. RCD operation (if applicable) : Rated residual operating current lan ens and operating time of ms (at lan)

PART 4: Declaration

have been
i We CERTIFY that the said works do not impair the safety of the existing installation, that the said works
designed, constructed, inspected and tested in accordance with BS 7671 : .2QQJ. (IEE Wiring Regulations),
of
amended to .........-+ ADA. .coseceese and that the said works, to the best of my/our knowledge and belief, at the time
my/our inspection, complied with BS 7671 except as detailed in Part 1.

Names CUAIVHECE:

For and on behalf of: .COUstY. FLCCEICS. scence Position... FLCCHUCUAM .eeesssessnescnneesneeene
Address: ..... 182. Industrial
Lane
Date: 1042004...

141
Appx 7
MINOR ELECTRICAL INSTALLATION WORKS CERTIFICATE
GUIDANCE FOR RECIPIENTS (to be appended to the Certificate)
This Certificate has been issued to confirm that the electrical installation work to
which it relates has been designed, constructed and inspected and tested in
accordance with British Standard 7671, (the IEE Wiring Regulations.)

You should have received an ‘original’ Certificate and the contractor should have
retained a duplicate. If you were the person ordering the work, but not the owner
of the installation, you should pass this Certificate, or a copy of it, to the owner. A
separate Certificate should have been received for each existing circuit on which
minor works have been carried out. This Certificate is not appropriate if you
requested the contractor to undertake more extensive installation work, for which
you should have received an Electrical Installation Certificate.

The Certificate should be retained in a safe place and be shown to any person
inspecting or undertaking further work on the electrical installation in the future. If
you later vacate the property, this Certificate will demonstrate to the new owner
that the minor electrical installation work carried out complied with the
requirements of British Standard 7671 at the time the Certificate was issued.

142
Appx 7
PERIODIC INSPECTION REPORT
NOTES:

1. This Periodic Inspection Report form shall only be used for the reporting on the
condition of an existing installation.
2. The Report, normally comprising at least four pages, shall include schedules of
both the inspection and the test results. Additional sheets of test results may be
necessary for other than a simple installation. The page numbers of each sheet
shall be indicated, together with the total number of sheets involved. The
Report is only valid if a Schedule of Inspections and a Schedule of Test Results
are appended.
3. The intended purpose of the Periodic Inspection Report shall be identified,
together with the recipient's details in the appropriate boxes.
4. The maximum prospective fault current recorded should be the greater of
either the short-circuit current or the earth fault current.
5. The ‘Extent and Limitations’ box shall fully identify the elements of the
installation that are covered by the report and those that are not; this aspect
having been agreed with the client and other interested parties before the
inspection and testing is carried out.

6. The recommendation(s), if any, shall be categorised using the numbered coding

1-4 as appropriate.

7. The ‘Summary of the Inspection’ box shall clearly identify the condition of the
installation in terms of safety.
8. Where the periodic inspection and testing has resulted in a satisfactory overall
assessment, the time interval for the next periodic inspection and testing shall
be given. The IEE Guidance Note 3 provides guidance on the maximum interval
between inspections for various types of buildings. If the inspection and testing
reveal that parts of the installation require urgent attention, it would be
appropriate to state an earlier re-inspection date having due regard to the
degree of urgency and extent of the necessary remedial work.
9. If the space available on the model form for information on recommendations
is insufficient, additional pages shall be provided as necessary.

143
Appx 7
 Form F 6 FormNo 126/6

PERIODIC INSPECTION REPORT FOR AN ELECTRICAL INSTALLATION (note 1)

(REQUIREMENTS FOR ELECTRICAL INSTALLATIONS - BS 7671 [IEE WIRING REGULATIONS))

DETAILS OF THE CLIENT =

Client; sss... NVA A DIO TU ee esa ces TE ee SOA career
Addresses eed Ld. Ante Street. TOWty,, COLES INT(aBIR x ct ete etcetera eat oar
Purpose for which this Report is required: ..... Mortg: OB EAS ase ides caus rete aia dusts 2 aadames pte t eee cannes (note 3)
DETAILS OF THE INSTALLATION "*P%°= 25 appropriate
Occupier: PA ADD ected en ter eRe Eee RRR REO OER ene etre cee Pe ye aero ate SU
Ar
iStelll
AtiCory SoS
5 IODA ese ates ee ea Pe PoC OTPe df N sea cassascu cerscdase ssn
NAAT OSS Tee OIE I er tee eR Een OT Renee ere ee ed See ene cerseeeeateeteneTT es
Description of Premises: Domestic (X Commercial [1] Industrial Other Oo
sores PLOOISORLIELTE
OTAe:tes ean tc bela cam Ses els ol es Sires, ce Sasa
Estimated age of the Electrical —seeeeseenes ALSa ae years
Installation:
Evidence of Alterations or Additions: Yes No [1 _ Notapparent O
If "Yes", estimate age: _............. Dine years
Date of last inspection: _........ ae cee Records available Yes L1 No ra
EXTENT AND LIMITATIONS OF THE INSPECTION (note 5)
Extent of electrical installation covered by this report: ....... installation to house, garage.and garden. Sic

Limitations: ....... NO. desmmanctlizeg

orGftiTigOfHOOTDORTAS. oo cccccccnssncssrcecseretnsotensegsenenssneceenrerteentetsneeeentsenet

This inspection has been carried out in accordance with BS 7671: 2001 (IEE Wiring Regulations), amended to 2004
Cables concealed within trunking and conduits, or cables and conduits concealed under floors, in roof spaces and
generally within the fabric of the building or underground have not been inspected.
NEXT INSPECTION (note 8)
We recommend that this installation is further inspected and tested after an interval of not more than 20... THortns/years,
provided that any observations ‘requiring urgent attention’ are attended to without delay.

DECLARATION
INSPECTED AND TESTED BY
Naricaen) (aViltc eee en eee tereeener
eine Signature: ......... UME Cee
For and on behalf of: .......cowmty, Flectrics ......... Position: ........ SEIT ONEN oot cccroseereereeteasotereeee
Address: .....287, Udustrigl Lane os cccssssssee
AA Re
cL OUTS An A Wa! Jabber os connve ter atee ASS cn eG UO ccoconeoececectcorcomonpmmmmmeesnens

Page lof 4

144
Appx 7
SUPPLY CHARACTERISTICS AND EARTHING ARRANGEMENTS 1% ?0%29 and enter details, as appropriate
Earthing arrangements Number and Type of Live Nature of Supply Parameters Supply
Conductors Protective Device
Characteristics
TN-C Oo alc. Mac Nominal voltage, U/Up!”) ........230......V
TN-S Ot j Nominal frequency, f"” .. Type: BS.1361......
TN-C-S 1-phase, 2-wire %2-pole oO Prospective fault current, lp‘? ...4:4%...kKA |... SM 6 ee
TT oO (note 4)
IT O
1-phase, 3 wire [] 3-pol
nese) Sewltenial}Si0o.e! ia) External loop impedance, Z, ...0.24.0 Nominal current
2-phase, 3-wire [Jother C] rating ...200......A
Alternative source [] (Note: (1) by enquiry, (2) by enquiry or by
of supply (to be detailed 3-phase, 3-wire [] measurement)
on attached schedules)
3-phase, 4-wire O
LLATION REFERRED TO IN THE REPORT Tick boxes and enter details, as appropriate
PARTICULARS OF INSTA
Means of Earthing Details of Installation Earth Electrode (where applicable)
Distributor's facility Type Location Electrode resistance
Installation oO (e.g. rod(s), tape etc) to earth
earthelectrode | nsssane SES Renee eee PeaSaRTT reese Beene nane ee eTeee Q
Main Protective Conductors
Earthing conductor: material von COPPET.... connection verified eh
Main equipotential bonding conductors material von COPPEM.... connection verified

To incoming water service wy To incoming gas service wy To incoming oil service al To structural steel ]
Tolightning protection (1 To other incoming service(s)L_] (state details... ec-ceeesesessieseseerersereteeeeeney )
Main Switch or Circuit-breaker

BS,Type.. 0486. seca ai se Pend neces ay No. of poles Meee Current rating 80...A Voltage rating ....... 240.N
Location... Meter.cupboard. Sorep ere Peco UceecLERCCCAER EceReO=tn Fuse rating or setting .===....
Rated residual operating current lan = . a
OBSERVATIONS AND RECOMMENDATIONS 119%? 2° approprisie ; Recommendations as
(note 9) detailed below
Referring to the attached Schedule(s) of Inspection and Test Results, and subject to the limitations specified at | note 6
the Extent and Limitations of the Inspection sgction
LINo remedial work is required The following observations are made:
conductors sizedper 15 editi

“Light pendants and lam pholder

“He EES
‘Broken sockett 1 in lou

One of the following numbers, as appropriate, is to be allocated to each of the observations made above to indicate to the person(s)
responsible for the installation the action recommended.
requires urgent attention requires improvement requires further investigation

does not comply with BS 7671: 2001 amended to 4204 This does not imply that the electrical installation inspected is unsafe.
SUMMARY OF THE INSPECTION E004
Date(s) of the inspection: ...... 28/6/2.00: geese arenes wepapndtieisnehcidsalnsaonxees pars
General condition of the installation: .... le urgent repairs and improve

Overall assessment: Sattstactery/Unsatisfactory (note 8)

SCHEDULE(S)
The attached Schedules are part of this document and this Report is only valid when they are attached to it.
suse 1... Schedule(s) of Inspections and .....L..... Schedule(s) of Test Results are attached.
(Enter quantities of schedules attached),

Page 2of 4

145
Appx 7
PERIODIC INSPECTION REPORT
GUIDANCE FOR RECIPIENTS (to be appended to the Report)
This Periodic Inspection Report form is intended for reporting on the condition of an
existing electrical installation.

You should have received an original Report and the contractor should have retained
a duplicate. If you were the person ordering this Report, but not the owner of the
installation, you should pass this Report, or a copy of it, immediately to the owner.

The original Report is to be retained in a safe place and be shown to any person
inspecting or undertaking work on the electrical installation in the future. If you later
vacate the property, this Report will provide the new owner with details of the
condition of the electrical installation at the time the Report was issued.

The ‘Extent and Limitations’ box should fully identify the extent of the installation
covered by this Report and any limitations on the inspection and tests. The contractor
should have agreed these aspects with you and with any other interested parties
(Licensing Authority, Insurance Company, Building Society etc) before the
inspection was carried out.

The Report will usually contain a list of recommended actions necessary to bring the
installation up to the current standard. For items classified as ‘requires urgent
attention’, the safety of those using the installation may be at risk, and it is
recommended that a competent person undertakes the necessary remedial work
without delay.

For safety reasons, the electrical installation will need to be re-inspected at

appropriate intervals by a competent person. The maximum time interval
recommended before the next inspection is stated in the Report under ‘Next
Inspection.’

The Report is only valid if a Schedule of Inspections and a Schedule of Test Results
is appended.

146
Appx 7
 Form F3 Form No 126/3
SCHEDULE OF INSPECTIONS
Methods of protection against electric shock Prevention of mutual detrimental influence

(a) Protection against both direct and indirect [Vv] (a) Proximity of non-electrical services and other influences
contact: [Vv] (b) Segregation of band | and band II circuits or band
insulation used
(i) SELV (note1)
Vv] (c) Segregation of safety circuits
(il) Limitation of discharge of energy
Identification
(b) Protection against direct contact: (note 2)

VW] (i) Insulation of live parts

B Presence of diagrams, instructions, circuit charts and
similar information
[X] (ii) Barriers or enclosures
(b) | Presence of danger notices and other warning notices
(iii) Obstacles (note 3)
NW
NNN
(c) Labelling of protective devices, switches and terminals
INA (iv) Placing out of reach (note 4)
(d) Identification of conductors
(vy) PELV
Cables and conductors
x (vi) Presence of RCD for supplementary
protection (a) Routing of cables in prescribed zones or within
mechanical protection
(c) Protection against indirect contact:
(b) Connection of conductors
(i) | EEBAD including: (c) Erection methods
(4) Presence of earthing conductor (d) Selection of conductors for current-carrying capacity and
VY
ANNNN
Presence of circuit protective conductors voltage drop

7] Presence of main equipotential bonding (e) Presence of fire barriers, suitable seals and protection
conductors against thermal effects

CX] Presence of supplementary equipotential General

bonding conductors
(a) Presence and correct location of appropriate devices for
Presence of earthing arrangements for isolation and switching
combined protective and functional
(b) Adequacy of access to switchgear and other equipment
purposes
(c) Particular protective measures for special installations
Presence of adequate arrangements for
and locations
alternative source(s), where applicable

Ss
& Presence of residual current device(s)
(d) Connection of single-pole devices for protection or
switching in phase conductors only
(ii) Use of Class Il equipment or equivalent
(e) Correct connection of accessories and equipment
insulation (note 5)
(f) | Presence of undervoltage protective devices
(iii) Non-conducting location: (note 6)
Absence of protective conductors (g) Choice and setting of protective and monitoring devices
for protection against indirect contact and/or overcurrent
(iv) Earth-free equipotential bonding: (note 7)
Presence of earth-free equipotential (h) Selection of equipment and protective measures

A
BN
N
NaN
N&
bonding conductors appropriate to external influences

(v) Electrical separation (note 8) (i) Selection of appropriate functional switching devices

Inspected by ..... W. White.

Notes:
v to indicate an inspection has been carried out and the result is satisfactory
x to indicate an inspection has been carried out and the result was unsatisfactory
NN to indicate the inspection is not applicable
LIM to indicate that, exceptionally, a limitation agreed with the person ordering the work prevented the inspection or test
being carried out.
SELV An extra-low voltage system which is electrically 5: Use of Class I] equipment - infrequently adopted and only
separate from earth and from other systems. The when the installation is to be supervised
particular requirements of the Regulations must be (see Regulations 413-03 and 471-09)
checked (see Regulations 411-02 and 471-02) 6. Non-conducting locations - not applicable in domestic
Method of protection against direct contact - will include premises and requiring special precautions
measurement of distances where appropriate (see Regulations 413-04 and 471-10)
Obstacles - only adopted in special circumstances re Earth-free local equipotential bonding - not applicable in
(see Regulations 412-04 and 471-06) domestic premises, only used in special circumstances
(see Regulations 413-05 and 471-14)
Placing out of reach - only adopted in special
circumstances (see Regulations 412-05 and 471-07) 8. Electrical separation (see Regulations 413-06 and 471-12)

Page 3of 4

147
Appx 7
 p JOp,aseg $}|NSaJ 4S} JO ajNPays UO Sa}OU aa x
Fiurrydas paou sunpuad unyby
sydyaos Loo punowl of GX ou
suoonpog 07 Furpuog hivyuamaddns ou
qos 00} sajquo Fuspuog uy; :sajou jejoeds pue suojenBoy Burs, wos suoyeiAoq
=a mal
——-
— £0 ST (ce aa = SL sz |09 oF i samoys
a v0 ST OC |)comemsl| es ws ST |Ss ST " Ol HA
Ws 70 Aes fh Ses Wu sz |09 0 u 4ayoo)
GX ou Sig #0 ci ra — Tr ican ||Shas og i umop Fux
spuoptiad fayrof — 20 ST ST _— scgTam |aes 0E f dn fury
spuepuadfara = er Z | | |S or |st § \ umopsrybiT
sneoputad fyyrof —l| ¢f Le |g Or OL NST Ss asf dn sryPrT
vis |e kan tbs | Obx 6x Ba | Le oe S v € 2 t
‘I zw | 7ww Vv
su o A OW OW | 6 wo wo
} u
awl} 1 | yuez | aan | | yy
4ayio | addy sZ 4 JRA | /2AIT fy] tytty ad> any | Buney | adAy
aoue e i
Burjsay -peduyj | a2uejsisay s10}Npuod wg
syseway jeuolpun4 dooq ° uoljejnsu} Ayinuijuo> Buin :Aypeded
yyeq d pind412-Yoys , uo} dis2seq PND
901Aeq
JUBIINIIBAC
sUNsoy jsoL
Pays pia wiiwh “Asidjg ~~ VOM 30 uondiuoseq
Aesauien casoscgnp taguabicon suvanehs wochiips GuniesmaAcnsmaW sm bacioxesea -Bunse} 0} e|qeloujna juewidinb3
Rea ceasaxsnsasecoeviceeseapcerentenys eneamae OT WT 381891 GOW
PT WT ‘uoneinsuy
TT WT ~ :Aynuluod tuiBlo ye 87 ,
So yy E79 aranenveet sayeq sel
+1 /S-O-NL/S=he :A\ddng jo adh, r
OT WT” seourpediu! doo}
sjuewunySU]
eae
sommzap
fpumo;y"*30\9e y,
UOD
S11Nsja¥ 1S31 40 JINGAHIS
ON WHOA p WOT
v/9ZE

Appx 7
148
NOTES ON SCHEDULE OF TEST RESULTS

* Type of supply is ascertained from the distributor or by inspection.

* Ze at origin. When the maximum value declared by the distributor is used, the effectiveness of the earth must be confirmed by a
test. If measured the main bonding will need to be disconnected for the duration of the test.

* Short-circuit capacity of the device is noted, see Table 7.2A of the On-Site Guide or 2.7.15 of GN3

* Prospective fault current (PFC). The value recorded is the greater of either the short-circuit current or the earth fault current.
Preferably determined by enquiry of the distributor.
The following tests, where relevant, shall be carried out in the following sequence:

Continuity of protective conductors, including main and supplementary bonding

Every protective conductor, including main and supplementary bonding conductors, should be tested to verify that they are continuous
and correctly connected.

*6 Continuity
Where Test Method 1 is used, enter the measured resistance of the phase conductor plus the circuit protective conductor (R1+ R2).
See 10.3.1 of the On-Site Guide or 2.7.5 of GN3.
During the continuity testing (Test Method 1) the following polarity checks are to be carried out:
(a) every fuse and single-pole control and protective device is connected in the phase conductor only
(b) centre-contact bayonet and Edison screw lampholders have outer contact connected to the neutral conductor
(¢) wiring is correctly connected to socket-outlets and similar accessories.
Compliance is to be indicated by a tick in polarity column 11.

(Rj + R2) need not be recorded if R2 is recorded in column 7.

*7 Where Test Method 2is used, the maximum value of R2 is recorded in column 7.
Where the alternative method of Regulation 413-02-12 is used for shock protection, the resistance of the circuit
protective conductor R2 is measured and recorded in column 7.
See 10.3.1 of the On-Site Guide or 2.7.5 of GN3.

*8 Continuity of ring final conductors

A test shall be made to verify the continuity of each conductor including the protective conductor of every ring final circuit.
See 10.3.2 of the On-Site Guide or 2.7.6 of GN3.

*9,*10 Insulation Resistance

All voltage sensitive devices to be disconnected or test between live conductors (phase and neutral) connected together and earth.
The insulation resistance between live conductors is to be inserted in column 9.
The minimum insulation resistance values are given in Table 10.1 of the On-Site Guide or Table 2.2 of GN3.
See 10.3.3(iv) of the On-Site Guide or 2.7.7 of GN3.

All the preceding tests should be carried out before the installation is energised.

*11 Polarity
A satisfactory polarity test may be indicated by a tick in column 11.
Only in a Schedule of Test Results associated with a Periodic Inspection Report is it acceptable to record incorrect polarity.
*12 Earth fault loop impedance Zs
This may be determined either by direct measurement at the furthest point of a live circuit or by adding (Ry + R2) of column 6 to
Ze. Ze is determined by measurement at the origin of the installation or preferably the value declared by the distributor used.
Z; = Ze + (R1 + Ra). Zs should be less than the values given in Appendix 2 of the On-Site Guide or App 2 of GN3.
*13 Functional testing
The operation of RCDs (including RCBOs) shall be tested by simulating a fault condition, independent of any test facility in the device.
Record operating time in column 13. Effectiveness of the test button must be confirmed.
See Section 11 of the On-Site Guide or 2.7.16 of GN3.
they are properly
*14 All switchgear and controlgear assemblies, drives, control and interlocks, etc must be operated to ensure that
mounted, adjusted, and installed.
Satisfactory operation is indicated by a tick in column 14.

Earth electrode resistance

The earth electrode resistance of TT installations must be measured, and normally an RCD is required.
on Forms 1, 2 or 6 as
For reliability in service the resistance of any earth electrode should be below 200 ©. Record the value
appropriate. See 10.3.5 of the On-Site Guide or 2.7.13 of GN3.

149
Appx 7
 APPENDIX 8

STANDARD CIRCUIT ARRANGEMENT FOR HOUSEHOLD AND

SIMILAR INSTALLATIONS

Introduction

This appendix gives advice on standard circuit arrangements

for households and similar premises. The circuits satisfy the
requirements of Chapter 43 for overload protection and
Chapter 46 for isolation and switching, together with the
requirements as regards current-carrying capacities of
conductors prescribed in Chapter 52 for the selection and
erection of wiring systems of BS 7671.

It is the responsibility of the designer and installer when

adopting these circuit arrangements to take the appropriate
measures to comply with the requirements of other chapters
or sections which are relevant, such as Chapter 41, Protection
against electric shock, Section 434, Protection against fault
current, Chapter 54, Earthing arrangements and protective
conductors, and the requirements of Chapter 52, Selection and
erection of wiring systems, other than those concerning
current-carrying capacities.

Circuit arrangements other than those detailed in this

appendix are not precluded when specified by a suitably
qualified electrical engineer, in accordance with the general
requirements of Regulation 314-01-03.

The standard circuit arrangements are:

- Final circuits using socket-outlets complying with BS 1363-2
and fused connection units complying with BS 1363-4
- Cooker final circuits.

- Final radial circuits using socket-outlets complying with

BS 4343 (BS EN 60309-2)

150
Appx 8
Final circuits using socket-outlets complying with BS 1363-2
and fused connection units complying with BS 1363-4

General

A ring or radial circuit, with spurs if any, feeds permanently

connected equipment and an unlimited number of socket-outlets
and fused connection units.

The floor area served by the circuit is determined by the known

or estimated load and does not exceed the value given in
Table 8A.

A single 30 A or 32 A ring circuit may serve a floor area of up to 433-02-04

100 m2. Sockets for washing machines, tumble dryers and
dishwashers should be located so as to provide reasonable
sharing of the load in each leg of the ring, or consideration
should be given to a separate circuit.

The number of socket-outlets is such as to ensure compliance

with Regulation 553-01-07, each socket-outlet of a twin or
multiple socket-outlet being regarded as one socket-outlet.

Diversity between socket-outlets and permanently connected

equipment has already been taken into account in Table 8A
and no further diversity should be applied.

TABLE 8A
Final circuits using BS 1363 socket-outlets and connection units
Minimum conductor
cross-sectional area*
Copper Copper
Overcurrent conductor conductor Maximum
Type of circuit protective | thermoplastic or mineral floor area
device thermosetting |insulated cables served
insulated cables
Rating A
3 4 5

A2

*The tabulated values of conductor size may be reduced for fused spurs

151
Appx
 Where two.or more ring final circuits are installed the socket-
outlets and permanently connected equipment to be served
are to be reasonably distributed among the circuits.

Circuit protection

Table 8A is applicable for circuits protected by:

- fuses to BS 3036, BS 1361 and BS 88 and
- circuit-breakers
Types B and C to BS EN 60898 or BS EN 61009-1 and
BS EN 6 0947-2 and
Types 1, 2 and 3 to BS 3871.

Conductor size

The minimum size of conductor cross-sectional area in the

circuit and in non-fused spurs is given in Table 8A. However,
the actual size of cable is determined by the current-carrying
capacity for the particular method of installation, after
applying appropriate correction factors from Appendix 6. The
current-carrying capacity so calculated shall be not less than:
20 A for circuit A1,
30 A or 32 A for circuit A2 (i.e. the rating of the
overcurrent protective device),
20 A for circuit A3 (i.e. the rating of the overcurrent
protective device).

The conductor size for a fused spur is determined from the total
current demand served by that spur, which is limited to a
maximum of 13 A.

When a fused spur serves socket-outlets the minimum conductor

size Is:
1.5 mm? for cables with thermosetting or thermoplastic
insulated cables, copper conductors,
1 mm2 for mineral insulated cables, copper conductors.

The conductor size for circuits protected by BS 3036 fuses is

determined by applying the 0.725 factor of Regulation 433-2-03;
that is, the current-carrying capacity must be at least 27 A for
circuits A1 and A3, and 41 Afor circuit A2.

152
Appx 8
Spurs

The total number of fused spurs is unlimited but the number

of non-fused spurs should not exceed the total number of
socket-outlets and items of stationary equipment connected
directly in the circuit.

A non-fused spur feeds only one single or one twin or multiple

socket-outlet or one permanently connected equipment. Such
a spur is connected to a circuit at the terminals of a
socket-outlet or junction box or at the origin of the circuit in
the distribution board.

A fused spur is connected to the circuit through a fused

connection unit, the rating of the fuse in the unit not exceeding
that of the cable forming the spur and, in any event, not
exceeding 13 A.

Permanently connected equipment

Permanently connected equipment is locally protected by a

fuse complying with BS 1362 of rating not exceeding 13 A or
by a circuit-breaker of rating not exceeding 16 A and of a type
listed above and is controlled by a switch meeting the
requirements of Regulation 476-03-04. A separate switch is not
required where compliance with 476-03-04 is provided by the
circuit-breaker.

Final radial circuits using 16 A socket-outlets

complying with BS 4343 (BS EN 60309-2)

General

Where a radial circuit feeds equipment the maximum demand

of which, having allowed for diversity, is known or estimated
not to exceed the rating of the overcurrent protective device
and in any event does not exceed 20 A, the number of
socket-outlets is unlimited.

Circuit protection

The overcurrent protective device is to have a rating not

exceeding 20 A.

153
Appx 8
 Conductor size

The minimum size of conductor in the circuit is given in Table 8A.

Where cables are grouped together the limitations of Para 7.2.1
and Appendix 6 apply.

Types of socket-outlets

Socket-outlets should have a rated current of 16 A and be of

the type appropriate to the number of phases, circuit voltage
and earthing arrangements. Socket-outlets incorporating pilot
contacts are not included.

Cooker circuits in household or similar premises

The circuit supplies a control switch or a cooker unit complying

with BS 4177, which may incorporate a socket-outlet.

The rating of the circuit is determined by the assessment of the

current demand of the cooking appliance(s), and cooker
control unit socket-outlet if any, in accordance with Table 1A of
Appendix 1. A 30 or 32 A circuit is usually appropriate for
household or similar cookers of rating up to 15 kW.

A circuit of rating exceeding 15 A but not exceeding 50 A may

supply two or more cooking appliances where these are
installed in one room. The control switch or cooker control
unit should be placed within two metres of the appliance, but
not directly above it. Where two stationary cooking appliances
are installed in one room, one switch may be used to control
both appliances provided that neither appliance is more than
two metres from the switch. Attention is drawn to the need to
provide discriminative operation of protective gear as stated in
Regulation 533-01-06.

Water and space heating

Water heaters fitted to storage vessels in excess of 15 litres

capacity, or permanently connected heating appliances
forming part of a comprehensive space heating installation, are
to be supplied by their own separate circuit.

Immersion heaters are to be supplied through a switched cord-

outlet-connection-unit complying with BS 1363-4.

154
Appx 8
Heights of switches and sockets

The Building Regulations require switches and socket-outlets

in dwellings to be installed so that all persons including those
whose reach is limited can easily use them. A way of satisfying the
requirement is to install switches and socket-outlets in
habitable rooms at a height of between 450 mm and 1200 mm 553-01-06
from the finished floor level - see Figure 8A. Unless the dwelling
is for persons whose reach is limited the requirements would
not apply to kitchens and garages but specifically only to
rooms that visitors would normally use.

The Building Regulations are not applicable in Scotland where

the Building Standards (Scotland) Regulations apply. The
Scottish regulations do not have specific minimum heights for
accessories, installations are required to generally comply with
BS 7671.

Fig 8A: Height of switches, sockets etc

Sockets
entry phon TV sockets
switches
doorbells a telephone jack points
1200 mm maximum

AAS0)GUTS) ee eee eerie | eeeeeea oe Mle WO IGE co terosccseaone minimum _.......

From Approved Document M, 1999 edition Section 8.

Number of socket-outlets

Sufficient socket-outlets are required to be installed so that all

equipment likely to be used can be supplied from a reasonably
accessible socket-outlet, taking account of the length of flexible
cords normally fitted to appliances and luminaires. (Regulation
553-01-07). Table 8B provides guidance on the number of 553-01-07
socket-outlets that are likely to meet this requirement.

155
Appx 8
 TABLE 8B
Recommended provision of socket-outlets
(All socket-outlets are twin)

Location No. of outlets

Lounge (1) (2) (3) (9)

Dining
Kitchen (3) (4) (5) (9)
Double Bedroom (3)
Single Bedroom (3) (6) (9)
Bedsitter
Hall 2 (7)
Stairs/Landing
Loft (7)
Study/Home office (7) (8) (9)
Garage
Utility Room (5)
(This table was prepared with the kind assistance of the ECA, Select, NHBC,
CDA and EIEMA).
Notes:
(1) The number of outlets depends on the size of the room.
(2) Two twin socket-outlets should be located close to the TV aerial outlet to allow
for TV, video etc. and ancillary equipment supplies

(3) Larger dwellings will require proportionally more socket-outlets than smaller
dwellings.

(4) Kitchens should be fitted with socket-outlets above work surfaces as well as
specific socket-outlets for built in appliances.

(5) A lower number of socket-outlets may be appropriate in a kitchen where the

washing machine, dryer, freezer etc. are expected to be installed in a separate
utility room.

(6) Bedrooms intended for younger persons should have adequate provision of
socket-outlets for computer and electronic equipment.

(7) One twin socket-outlet should be installed near any telephone outlet to supply
mains powered telecommunication equipment.

(8) The provisions for an office at home may require more consideration with the
user to identify and locate all necessary equipment than is the case with an
ordinary domestic installation.

(9) The use of IT and other electrical equipment with high earth protective 607-02
conductor currents may require the application of Regulation 607 to
accommodate cumulative leakage currents.

156
Appx 8
APPENDIX 9

RESISTANCE OF COPPER AND ALUMINIUM CONDUCTORS

To check compliance with Regulation 434-03-03 and/or 434-03-03

Regulation 543-01-03, i.e. to evaluate the equation s? = I? tk, it 543-01-03
is necessary to establish the impedances of the circuit
conductors to determine the fault current | and hence the
protective device disconnection time t.

Fault current | = Ud/Zs

where

Uo is the nominal voltage to earth,

Zs; is the earth fault loop impedance.

Z; = Ze + R1 + R2

where

Ze is that part of the earth fault loop impedance external to

the circuit concerned,

Riis the resistance of the phase conductor from the origin of

the circuit to the point of utilization,

R2 is the resistance of the protective conductor from the

origin of the circuit to the point of utilization.

Similarly, in order to design circuits for compliance with BS 7671

limiting values of earth fault loop impedance to those given in
Tables 41B1, 41B2 and 41D of BS 7671, or for compliance with
the limiting values of the circuit protective conductor given in
Table 41C, it is necessary to establish the relevant impedances
of the circuit conductors concerned at their operating
temperature.

Table 9A gives values of (R1 + R2) per metre for various

combinations of conductors up to and including 50 mm?
cross-sectional area. It also gives values of resistance
(milliohms) per metre for each size of conductor. These values
are at 20 °C.

157
Appx 9
 TABLE 9A
Value of resistance/metre for copper and aluminium conductors and
of R1 + R2 per metre at 20 °C in milliohms/metre

Cross-sectional area Resistance/metre

(mm?) or (R1 + R2)/metre (mQ/m)

Phase Protective
conductor conductor Aluminium

ree
aera
aE mau

4
4
4 Ul
ul
4
6
6 ul

6
6 a
Pn

158
Appx 9
TABLE 9B
Ambient temperature multipliers to Table 9A

Expected ambient temperature Correction factor

note

Note:
The correction factor is given by:
{1 + 0.004 (ambient temp - 20 °C}
where 0.004 is the simplified resistance coefficient per °C at 20 °C given by BS 6360
for copper and aluminium conductors.

For verification purposes the designer will need to give the

values of the phase and circuit protective conductor resistances
at the ambient temperature expected during the tests. This
may be different from the reference temperature of 20 °C
used for Table 9A. The correction factors in Table 9B may be
applied to the Table 9A values to take account of the ambient
temperature (for test purposes only).

Multipliers for conductor operating temperature

Table 9C gives the multipliers to be applied to the values given

in Table 9A for the purpose of calculating the resistance at
maximum operating temperature of the phase conductors
and/or circuit protective conductors in order to determine
compliance with, as applicable:

(a) earth fault loop impedance of Table 41B1, Table 41B2 — Table 4181
or Table 41D of BS 7671 Table 41B2
Table 41D
(b) earth fault loop impedance and resistance of protective
conductor of Table 41C of BS 7671. Table 41C

Where it is known that the actual operating temperature under

normal load is less than the maximum permissible value for the
type of cable insulation concerned (as given in the Tables of

159
Appx 9
 current-carrying capacity) the multipliers given in Table 9C may
be reduced accordingly.

TABLE 9C Standard devices

Multipliers to be applied to Table 9A to calculate conductor Table 41B1
resistance at maximum operating temperature Table 41B2
Table 41C
Conductor Insulation Table 41D

Conductor sone
Installation thermoplastic |thermosetting | thermosetting
(rubber)

Table 54B
Not incorporated
in a cable and
not bunched -
note 1

Table 54C
Incorporated ina
cable or bunched
- note 2

Note 1 See Table 54B of BS 7671: applies where the protective conductor is Table 54B
not incorporated or bunched with cables, or for bare protective
conductors in contact with cable covering.

Note 2 See Table 54C of BS 7671: applies where the protective conductor is a Table 54C
core in a cable or is bunched with cables.

The multipliers given-in Table 9C for both copper and

aluminium conductors are based on a simplification of the
formula given in BS 6360, namely that the resistance-
temperature coefficient is 0.004 per deg C at 20 °C.

160
Appx 9
APPENDIX 10

PROTECTIVE CONDUCTOR SIZING

TABLE 10A
Main earthing and main equipotential bonding conductor sizes
(copper equivalent) for TN-S and TN-C-S supplies

Phase conductor or
neutral conductor of
PME supplies

Earthing conductor 542-03-01

not buried or buried
protected against Gul 6 10m 16) 16. 169 25m 25) oa
corrosion and
mechanical damage
see notes

Main equipotential
bonding conductor Go Ge peor 1013 10s IOS Om e?> ato
see notes

Main equipotential
bonding conductor 1 Wo GT 1 WW Ws 2s Mls
for PME supplies
(TN-C-S)

Notes to Table 10A:

le Protective conductors (including earthing and bonding conductors) 543-02-03
of 10 mm? cross-sectional area or less shall be copper.

2 Regional electricity companies may require a minimum size of

earthing conductor at the origin of the supply of 16 mm? copper or
greater for TN-S and TN-C-S supplies

3: Buried earthing conductors must be at least : 542-03-01

2 : : Table 54A
25 mm? copper if not protected against mechanical damage or
corrosion
50 mm? steel if not protected against mechanical damage or corrosion
16 mm2 copper if not protected against mechanical damage but
protected against corrosion
16 mm2 coated steel if not protected against mechanical damage but
protected against corrosion

4. The distributor should be consulted when in doubt.

161
Appx 10
 ‘py JO € SUWUNJOD - Sed-aAIIDNPUOI-pasodxa UBAaMIaq sPpUOg 10} pasinbad }eUy
eu} Ja||eWS OU aq JsNnW PUOG au} ‘Wed-anly2NnpUOd-pasodxe Ue O} Pa}2BULOD SI! SLed-BAIJDNPUOI-SNOSUeIIX9 BUY} JO BUO }] 1 940N
zuwiw zuiw 7 WU
papeajoid pape}o01d papeajoid , papeaj}oid papeajoid papejoid JoyNpuo?
Ajjed1ueudaW JOU Ajjed1ueydaui | Ajjediueydaw YOU Ajjed1ueyraw | Ajje.!ueydaWwW JOU Ajjyed1ueydoW aAipejoid
}INDIID $O 9ZIS
(L) Wed-anljInpuod-snosuel}X9 yed-anijpnpuod-pasodxa yed-anipnpuod-snosuesxa}
0} ed-aAlyNpUOd-sNoOsuUeIIXA 01 Yed-aAlpNpuod-pasodxy 0} Wed-anl~npuod-pasodxy
Bulpuog Aueyuawajddns jo ease jeUuO!DAaS-ssO1D WUINWIUII
$10}2npuo> Hulpuog Aie}uawiajddns
€0-LvS d0l F1aVL

Appx 10
162
 Appx 10
163
WW 9 UeY} ssa] JOU pu JOP NPUOD Huiyyea
au} 10} pasinbay yey} Jey UY} ssa] JOU JO ease [eUOIIDAS-ssoJD eB BAY ||EYsS JOP NPUOD Hulpuog jeljua}odinba ujew sy

~
‘Z0-L0-€7S UONe|nBay Jad se aulwuajap WYO | Ue} Ssa| SeQUepad! 104
“yjyeaus e Aq uolsoijo2 ysulebe pa}a}014

‘SOON
jediueydow
jediueyudowW

oabewep
abewep

7Uu
UOo!lsolo>

UO1SO1109

Z
pue

pue Uolso1105 UOISOIIOD

ysuieBe payde3}01g =~} ysulebe pa}de}01q4 papej}oiduy ysulebe pa}de}0ld ysureBe pay9}0ld pepes}oidup
paling 10N paiing
(0) Wyo L
uey} ssa] Jou sa2uepadu! doo] 3jne} Yea 4105 saljddns 1} 404 (es>) Ease [eEUO!}IaS-SsO‘D 10}2NPUOD Hulyzies saddoD
LO-ZvS DOL JIESVL
 App7
APPENDIX 11

IDENTIFICATION OF CONDUCTORS

1. Introduction

The requirements of BS 7671 have been harmonized with the

technical intent of CENELEC Standard HD 384.5.514:
Identifica tion, including 514.3: Identific ation of conductors.
The cable standards have been harmonized with CENELEC
Harmonization Document HD 308 $2: 2001 Identification of cores
in cables and flexible cords. These standards specify the cable
core marking including cable core colours to be implemented
in the CENELEC countries.

This appendix provides guidance on marking at the interface

between old and harmonized colours, and general guidance
on the colours to be used for conductors.

British Standards for fixed and flexible cables have been

harmonized with the colours in HD 308 $2. BS 7671 has been
modified to align with these cable colours, but also allows
other suitable methods of marking connections by colours
(tapes, sleeves or discs), or by alphanumerics (letters and/or
numbers). Methods may be mixed within an installation.

Installations commencing on-site after 31 March 2004 and

before 1 April 2006 may use the new harmonized identification
or the old, but not both. Installations commencing on-site
after 1 April 2006 must use harmonized identification.

164
Appx 11
 Table 51
TABLE 11A 514-03-01
Identification of conductors (harmonized)

Function Alphanumeric Colour

Protective conductors Green-and-yellow

Functional earthing conductor Cream

a.c. power circuit")

Phase of single-phase circuit Brown
Neutral of single- or three-phase circuit Blue
Phase 1 of three-phase a.c. circuit Brown
Phase 2 of three-phase a.c. circuit Black
Phase 3 of three-phase a.c. circuit Grey

Two-wire unearthed d.c. power circuit

Positive of two-wire circuit Brown
Negative of two-wire circuit Grey

Two-wire earthed d.c. power circuit

Positive (of negative earthed) circuit Brown
Negative (of negative earthed) circuit? Blue

Positive (of positive earthed) circuit? Blue

Negative (of positive earthed) circuit Grey

Three-wire d.c. power circuit

Outer positive of two-wire circuit
derived from three-wire system Brown
Outer negative of two-wire circuit
derived from three-wire system Grey
Positive of three-wire circuit Brown
Mid-wire of three-wire circuit\?@) Blue
Negative of three-wire circuit Grey

Control circuits, ELV and other applications

Phase conductor Brown, Black, Red,
Orange, Yellow,
Violet, Grey, White,
Neutral or mid-wire™) Pink or Turquoise
Blue

4) Power circuits include lighting circuits.

2) Miidentifies either the mid-wire of a three-wire d.c. circuit, or the earthed
conductor of a two-wire earthed d.c. circuit.
3) Only the middle wire of three-wire circuits may be earthed.
(4) An earthed PELV conductor is blue .

165
Appx 11
 2. Alteration or addition to an existing installation

2.1. Single-phase

An alteration or an addition made to a single-phase

installation need not be marked at the interface provided that:
i) the old cables are correctly identified by the colour red
for phase and black for neutral, and
ii) the new cables are correctly identified by the colour
brown for phase and blue for neutral.

2.2. Two-or three-phase installation

Where an alteration or an addition is made to a two- or a

three-phase installation wired in the old core colours with
cable to the new core colours, unambiguous identification is
required at the interface. Cores shall be marked as follows:
Neutral conductors
Old and new conductors: N
Phase conductors
Old and new conductors: Me Le 3:

TABLE 11B Table 7A

Example of conductor marking at the interface for additions and
alterations to an a.c. installation identified with the old cable colours

Function New conductor

Marking Colour
Phase 1 of a.c. Red L1 L1 Brown")
Phase 2 of a.c. Yellow L2 L2 Black‘)
Phase 3 of a.c. Blue L3 L3 Grey‘)
Neutral of a.c. Black N Blue
Protective conductor] Green-and-Yellow Green-and-Yellow
'
™) Three single-core cables with insulation of the same colour may be used if
identified at the terminations.

3. Switch wires in a new installation or an alteration

or addition to an existing installation

Where a two-core cable with cores coloured brown and blue is

used as a switch wire, both conductors being phase conductors,
the blue conductors shall be marked brown or L at its
terminations.

166
Appx 11
 4. Intermediate and two-way switch wires in a new
installation or an alteration or addition to an
existing installation

Where a three-core cable with cores coloured brown, black

and grey is used as a switch wire, all three conductors being
phase conductors, the black and grey conductors shall be
marked brown or L at their terminations.

5. Phase conductors in a new installation or an

alteration or addition to an existing installation

Power circuit phase conductors should be coloured as in Table 11A.

Other phase conductors may be brown, black, red, orange,
yellow, violet, grey, white, pink or turquoise.

In a two- or three-phase power circuit the phase conductors

may all be of one of the permitted colours, either identified L1,
L2, L3 or marked brown, black, grey at their terminations to
show the phases.

6. Changes to cable core colour identification

TABLE 11C Table 7B

Cable to BS 6004 (flat cable with bare cpc)

Cable type New core colours

Single-core + bare cpc Brown or Blue

Two-core + bare cpc Brown, Blue

Alt. two-core + bare cpc Brown, Brown

Three-core + bare cpc Brown, Black, Grey

Table 7C
TABLE 11D
Standard 600/1000V armoured cable BS 6346, BS 5467 or BS 6724

Cable type New core colours

Single-core Brown or Blue

Two-core Brown, Blue

Three-core Brown, Black, Grey

Four-core Brown, Black, Grey, Blue

Five-core Red, Yellow, Blue, Black, | Brown, Black, Grey, Blue,

Green-and-Yellow Green-and-Yellow

167
Appx 11
 TABLE ALE Table 7D
Flexible cable to BS 6500
Cable type Old core colours New core colours
Two-core Brown, Blue No change
Three-core Brown, Blue, No change
Green-and-Yellow
Four-core Black, Blue, Brown, Brown, Black, Grey,
Green-and-Yellow Green-and-Yellow
Five-core Black, Blue, Brown, Black Brown, Black, Grey, Blue,
Green-and-Yellow Green-and-Yellow

7. Alteration or addition to a d.c. installation

When an alteration or an addition is made to a d.c. installation

wired in the old core colours with cable to the new core
colours, unambiguous identification is required at the interface.
Cores shall be marked as follows:
Neutral and mid-point conductors
Old and new conductors: M
Phase conductors
Old and new conductors: Brown or Grey, or
old and new conductors: L, L+ or L-.

TABLE TIF Table 7E

Example of conductor marking at the interface for additions and
alterations to a d.c. installation identified with the old cable colours
Function Old conductor New conductor
Colour Marking | Marking Colour
Two-wire unearthed d.c. power circuit
Positive of two-wire circuit L+ Brown
Negative of two-wire circuit L- Grey

Two-wire earthed d.c. power circuit

Positive (of negative earthed) circuit L+ Brown
Negative (of negative earthed) circuit M Blue
Positive (of positive earthed) circuit M Blue
Negative (of positive earthed) circuit L- Grey

Three-wire d.c. power circuit

Outer positive of two-wire circuit
derived from three-wire system L+ Brown
Outer negative of two-wire circuit
derived from three-wire system L- Grey
Positive of three-wire circuit L+ Brown
Mid-wire of three-wire circuit M Blue
Negative of three-wire circuit

168
Appx 11
 PICTORIAL INDEX

A four part pictorial index follows comprising the following

schematic diagrams:
Page

The installation Indexi 170

Bonding and earthing Index ii 173

Special locations and RCDs Index iii 174

Inspection and testing Index iv 176

To use the index, turn to the relevant index, and find paragraph
references against the appropriate schematic drawing.

169
 Shere
sejqeo

J
VIVO
sebe}on

~~
JUSIOSJI
JEUILUOU

aouesaid
Bumjeqey

a
Lg jo
(1)
BHuipeseoxe
peyoedxeun

(I!) abeljon

AOE

Lg Slemous
)

pue swoouyeq
pue

()b9
Bujeqel _
=
801Aep
LQ (WA)
e10W ue} auo Aq
Huryjaqeeiostpuliede|
uolejos! w oy
\ BAI}0E}01dSEDIABP
8o10yo
JO
Be
YOUMS
y'S
Aouebiewe
(1!) °G UOIFeIOS|
zg Bulyowms =~
jeuoljoun}
g 98S BulyouMs
pue uoyejos! |
\ SUO!}IPUCD
Hulpuog A €8 peuinsse
Buu ie <Y tae peuinbes s! LZ eqe
aunjonuys yg ums —_UB|s UoSU (Ales ‘epod d| = (XI)7'7SyNDID = UOMUEHE =—syinouio yeu
UOIPeUOJUI See ea juawidinbe jeuia}xe |pueq seinoed = peuonuanuood
Z| UONeWOJU! dISeq
NOILVTIVLSNI 3H (!) xepul

170
 JUawdinbse

171
()L'9°E

solsuajoeseuo
BdIMas
InoKe|
614
‘e}

pure (A)z’z GO 40
Jo az

SJaWUNSUOD
UleW
YOUMS

JOyeM
seb

A\ddnsbh
L°€
BOIASp
(\)Z'g yno-yno
eee
adh}
@Aoe}0Jd
Jo
(ve $J0}NqUySIP
S9DINIOS
}OB]UOD
JOAIIP jeluesse (uo?

fan ew
ysurebe
uoloe}01d 40}OWW
s]le}
(x1) 1-9 Buysse} (Al)e'%

==7)[ea2
pue
Bunoedsul YOUMS SJaijddns

S$Jaijddns
oipoued
BHuyjaqe|
(Woe

49}8W
801lAep
(pe ea10yo
Go
2g
Buiyoyms

40 L
__—
yeuonouny
(1x) L°g pure (x!) ,°9
‘(A) Lg Buyjeqe| JOB}UOD JOSJIPU!

puewep
uoloe}0
sureBe

Ajissaaip
¢Ge soul}
(Sswa\shs

UO!}JOSUUODSIP
S-9-NL

ddyf
uoWNqUsIp

Buidnosb
lb
bod

sajqeo
UOHe/OS!
S-NL

pueog
pue

‘LL

uoi08}01d
JOJ)
|°G

o9€

GOU

Aq
GOUY k'9°€
(WD L'9°E GO"

Burjjeqe|
uol0a}01d
Aq
Aq
uonoejo

syoddns
(1x)
€'€
uooejoid

LQ
uold98}01d

uonoejes
ajqeo
peo|iaAo
juewno-1jne4

ddy
ajqeo
Ge

¢ tp
iddy{
wy,
 main ventilation *
ducting

lightning protection By]

systems 4.1 (vi) i KR eon

central heating * ae other service

and air conditioning pipes 4.1 (iii)
4.1(iv)

exposed metallic *
structural parts oil
4.1(v) accessible *
structural
steelwork ese

lightning
conductor

exclusion of copper
covered aluminium
conductors 4.2(i)

.
labelling 6.1 (iv) |

Px
; earthing
lightning Ny conductor 4.2
conductor ‘ NI
test point /\ main bonding comductors|4.2

main earthing terminal

earl

Se
earth electrode 4.8 earth fault loop impedance
— maximum value 1.1 (iv),
4.8
* metal parts only require main bonding when they
are extraneous-conductive-parts, see Section 4

172
 Index (ii) BONDING AND EARTHING
See also Fig 4a, Fig 4b and Fig 4c
information
structure
wiring
bonding

gas installation
pipes 4.1(ii)

labelling 6.1 (iv)

main water pipes
4.1(i)

cooker

fal fre sl
a
Sas)
PSs

ia a Ba S46 e7en®

earthing
conductor circuit protective conductors
4.2

Exposed-conductive-parts
(cooker, switch plates, metal)

main earthing terminal may be Ea ME nes conventional final

inside the distribution board circuits
Sec 7

173
 |g pauinbeu sI z' 1g Buneey
uonueye sejnored Joo|epun
wodluyeq
woojpeq
1g ajqe) seuoz
ul juawidinbe jeoujo8|98 8 a|qe] SOUOZ JO}
gjqeyins yuewdinbe
e
Z'8 BjOIGno 4amoys Z'g wooipeq
a ec
UYIM WOO! Ul ey90S —U!_ 8J91GNd JaMoYs
Lg aiqel yyeq au}
Bulpuoq uIUIM JUsUdINbe
Bui jeoujo9a
eunjoniys
Oe SGDYU GNV SNOILVDO7 1VID3dS (1!) xepul

174
 €°g pauinbei S| cr

175
JejNoIed uolueye 9€ eel
on dou
abeiebh/peys
L'L'8(Al)
dou Gol
sedlAep 8Al}0e}01d
WH (LDLITI
pueog uoWNqUIs!p
LOE cS
sJoopj}no yuewdinbe Buryy6i
ajqeuod A\jddns Loe af ah
0} pe}0edx9 JayD0S sJoopyno juewdinbe
cGe ajqeuod A\ddns a
SyINoJIO 0} payoedxe ja490
jeloeds
4J8MOUS JOBACYS uel
J@Moys
 Le6
1SI}4OOUO 1S9}
2 ddy
gouepedtul doo} € Ol
sainpeooid se}
€'€'0} Bursa}
eoue\sised
uolye|nsul
veo
Bunse} Ayejod
ZO} pue
Leo} Bunse} 7 Ol S}S9}
Aynuyuod
jo eouanbes
LO} Busey
Huunp Ajeyes
Ol 99S
saj}ou eouepin6
Hulse} elul
Hulpuog
Bum
eunjoniys
UOIEUWOJU! DNILSAL GNV NOILD4 dSNI (A!) Xepul

176
 177
ddy
‘16
LZ

uolye}USLUNDOP UO!}e|dWo0d
syne}
€'6
JO UO!}08109 9 OL
Hulse} eouepedui!
jeul9a}xe pue
€6

sjuewalinbes Buse} doo yjney yueR

oc6

seposjoeja
yS!p4OeYO UOHOedsul

Buse}Ge
or
yee
L'Z'6 uoNoedsul
esodind
jo

jo
L6 }S9}
pure joedsul
0} JueWAaIINbe1
Buse}

08g
"SGOU

LL
40
 Index (v) ALPHABETICAL

See page 164 for pictorial indexes

Para Page
A
Alarms, smoke 7.4.1 56
Alphanumeric Table 11A 165
B
Band| 9:22
Band Il 9272
Bathrooms 4.5
4.7
fees
8.1
Bonding 4
Appx 10
BS 1363 socket-outlets Appx 8
Building Regulations det
Fig 8A
Cc
Cable
bends Table 4E
floors and ceilings e351
ratings Appx 6
resistance Appx 9
selection Appx 3
spans (overhead wiring) Table 4B
supports Appx 4
walls es2
Capacities
conduits Appx 5
trunking Appx 5
Ceilings Took
Central heating 4.1
Certificates gal
Appx 7
Checklist
circuit He2es
inspection O22
testing 55a
Circuit arrangement Appx 8
Circuit-breaker selection Table 7.2B
Circuits 7
Colours, cable core Appx 11
Corrosion Appx 3
178
Competent person Preface
Conduit supports Table 4C
Conduit capacities Appx 5
Consumer unit Bo
Figs 3a, 3b
Figs 4a, 4b, 4c
Consumer's controlgear 2.2(v)
Continuity testing 9.3
10.3.1
of rings 10.3.2
Cooker circuit Table 1A
Table 1B
Corrosion Appx 3
Current-carrying capacity Appx 6
Cut-out 1.1(iii)
2.2(i)
D
cee Appx 11(7)
Diagrams 6.1(x)
Direct contact 3.4(i)
Direct current Appx 11(7)
Disconnection times 3.5
L225
Distribution board 33
Figs 3a, 3b
Figs 4a, 4b, 4c
Distributor’s cut-out 1.1(iii)
2.2(i)
Diversity Appx 1
E
Earth electrode
testing
types
Earthing
conductor size
TN-C-S
TN-S
-
Earth fault loop impedance
circuits
RCD
supply
testing

Electrical installation certificates Appx 7

179
 Electric shock 3.4 7
58
Emergency lighting 74.2 Bi,
Emergency switching 5.4 35
Equipotential bonding 24
F

Fault current
measurement 10.3.7 80
protection 33 li?
72.5 (1) 49
Table 7.2A 50
Final circuits 7 40
Fire alarms VAA 56
Fireman’s switch 5.4 35
Fixed wiring Table 3A 94
Flexible cords Table 3B oT,
Floors el 52
Functional
extra-low voltage 10.3.3(vi) 75
switching a2 35
testing 10.3.8 80
Fuses Te2eD 49
distributor’s 1.1(ili) 11
272\\) 14
G
Garages 8.3 60
Garden buildings 8.3 60
Gas pipes 4.1 24
Gas service 4.2 24
Grouping e2s|
Table 6C 118
H
Hand-held equipment 3.5.2(ii)
Hearing aid loop 7.3.4
Height of overhead wiring Table 4B
Height of switches, sockets Fig 8A
I
Immersion heaters Appx 8
Indirect contact 3.A(ii)
Information fez
Inspection and Testing 9
Inspection certificate Appx 7
Inspection schedule SU
Appx 7

180
Insulation resistance a5
IOs
Isolation Dal
J
Joists i341
L
Labelling 6
Lighting demand Table 1A
diversity Table 1B
Lightning protection
Live part
Load characteristics
Load estimation
Loop impedance
testing
M
Main earthing
bar Figs 4a, 4b, 4c
bonding Figs 4a, 4b, 4c
terminal Figs 4a, 4b, 4c
Maximum demand Appx 1
Mechanical maintenance oye)
Metal pipework

Metal structures
Meter
Meter tails 2.2(iii)
Figs 4a, 4b, 4c
Mineral cable Table 3A
Minor works certificate Appx 7
Motors diversity Table 1B
N
Notices 6
Number of socket-outlets Table 8B

O
Oil service pipe 4.2
Overhead wiring Appx 4
Overload protection ane
P
Partition walls Pl Pe
PELV 3.A(iii)
Ddait
Table 10.1
10.3.3(v)
Periodic reports Appx 7
181
 Plastic pipes
Polarity testing

Portable equipment
Protection
Protective conductors
Protective conductor current
Protective device
Proximity
R
Radial circuits
testing
RCBO
RCD
RCD testing
Reference method
Reports
Resistance of conductors
Ring circuits
testing
S
Schedules

Scope
SELV

Table 10.1
10.3.3(v)
Sequence of tests 10.2
Service position 2
Short-circuit protection 33
Table 7.2A
Showers 8
Skilled persons 121
Smoke alarms Ae
Socket-outlets 3.6.1
Appx 8
Special locations 8
Spurs Appx 8
Standard circuits Appx 8
Supplementary bonding 4.5
4.6
4.7
Table 10B

182
Supplier's cut-out see distributor’s cut-out
Supplier’s switch oe
Supply 4
Supply tails Figs 4a, 4b, 4c
Switching 5
Switches, height of Fig 8A
T
Telecommunication circuits ase
Temporary buildings 3
Test equipment 10.1
Test results schedule onl
Appx 7
Testing a
10
Thermal insulation Appx 6
Thermoplastic (pvc) cable 7.1
Table 6D1
Table 6E1
Table 6F
Thermosetting cable 7.2.2
Table 6D1
Table 6E1
TN-C-S system Fig 4b
TN-S system Fig 4a
Trunking
capacities Appx 5
supports Table 4D
TT system Fig 4c
7.2.4
Two-way circuits Fig 7.3.4
10.3.3(ii)
U
Underfloor heating Saez 58
V
Voltage bands 9.2.2 62
Voltage drop Appx 6 115
Table 6D2 122
Table 6E2 126
Table 6F 126
Ww
Walls Das 53
Warning notices 6
Water heaters Appx 8 150
Water pipes 4.1 24

183
 eeceemmenpenee® —_—

IEE Support for BS 7671 : 2001

The IEE publishes a range of books and runs courses and services for industry to support the
use and application of BS 7671.

GUIDANCE NOTES
The IEE’s series of Guidance Notes offers extensive, industry-endorsed guidance to
designers and installers in the effective use of BS 7671.
Seven IEE Guidance Notes are currently available:
1. Selection and Erection of Equipment 5. Protection against Electric Shock
2. Isolation and Switching 6. Protection against Overcurrent
3. Inspection and Testing 7. Special Locations
4. Protection against Fire

COMMENTARY ON BS 7671 : 2001

Written for designers and managers by the IEE’s former Principal Engineer, Paul Cook, this
title provides clear interpretations of and guidance to the Regulations.

CODES OF PRACTICE
The IEE Code of Practice for In-Service Inspection and Testing of Electrical
Equipment offers guidance for the inspection, testing and maintenance of electrical
appliances, plus advice on compliance with health and safety legislation.
The IEE Electrical Maintenance - Code of Practice offers guidance on electrical aspects of
building maintenance, including electrical installation, fire alarms, emergency lighting and
more, plus detailed guidance on legal responsibilities.

CD-ROM OF IEE WIRING REGULATIONS

The CD-ROM version of BS 7671 (incorporating all amendments) is a fully-structured
electronic reference tool, hyperlinked and fully cross-referenced. As well as BS 7671, the
CD-ROM contains the On-Site Guide, all seven Guidance Notes and both IEE Codes of
Practice.

To order any of these publications, please contact the IEE:

e by telephone: 01438 767328 e by fax: 01438 742792
e by email: [email protected] e via our website: www.iee.org/shop
For free downloads, updates and to join our email list, visit www.iee.org/technical

Please send me further information on the following IEE products and/or courses:

C1 BS 7671 IEE Wiring Regulations

/ CD-ROM L] On-Site Guide
LJ Guidance Notes / Commentary L] Codes of Practice

C Part P (Building Regs) Competent Persons Scheme LJ Training Courses

LJ Please add my details to your mailing list for future product news/updates

; Name
:Company
7Address

'Post code nail

 »

TRAINING AND SHORT COURSES

The IEE offers a full range of training for BS 7671 and its amendments. Both
public and in-company courses are available.
Design — Two-day course
Level 3 Certificate in Requirements for Electrical Installations BS 7671 —
Two-day course (Qualifying C & G 2381)
Testing of Electrical Installations — One-day course.
Level 3 Certificate in Inspection, Testing and Certification of Electrical
Installations — Three-day course (Qualifying C & G 2391)
Portable Appliance Testing — Two one-day courses
(Incorporating Management of Electrical Equipment qualifying C & G 2377-001
and Inspection and Testing of Electrical Equipment qualifying C & G 2377-002)
Electrical Maintenance — Two-day course
Electricity at Work — One-day course

Dates and venues for these and other courses can be found from the IEE:
e by telephone: 01438 767288 e by fax: 01438 767291
e by email: [email protected] e via the web: www.iee.org/courses

COMPETENT PERSONS SCHEME

Under Part P of the Building Regulations, domestic installation work will have
to be inspected by Local Authority Building Control officers unless carried out
by a ‘Competent Person’ who can self-certify the work. The IEE supports the
Part P Competent Person Scheme arranged by BRE-Certification and the ECA.
Details can be received by returning the reply paid card below

BUSINESS REPLY SERVICE

License No. SG 250/18

Wiring Regulations Enquiries

The IEE
Michael Faraday House
Six Hills Way
STEVENAGE
UK
SG1 2BR
 Symbols
Socket-outlet Integrating
instrument or
Energy meter
etSwitched * function
socket-outlet Wh = Watt-hour
VArh = Volt
o& Switch
ampere reactive
hour
2 way switch,
ee single-pole Load
* details
ny Intermediate
Motor starter
switch
* indicates type
Pull switch,
Class Il
single-pole
(O] appliance
Lighting outlet Class III
O position appliance
Fluorescent Safety isolating
luminaire transformer
Wall mounted tsolating
luminaire transformer

Emergency fuse link, rated

lighting current in
luminaire (or amperes
special circuit)
Operating
Self-contained device (coil)
emergency Make contact -
lighting
normally open
luminaire
Break contact -
© Push button normally closed
Manually
a) Clock
operated switch

A Three-phase
winding - delta

YW Buzzer Three-phase
winding - Star
[kK Horn Changer,
Converter,
@ Telephone
handset

oC) Microphone

cx Loudspeaker Primary cell -

longer line
positive, shorter
otsAntenna,
line negative

@ Machine 4H Battery
* Function
M = Motor -~QD- Transformer -
G = Generator general symbol
Generator 10° giga G
10° mega M
@® Indicating 103 kilo k
instrument
* function
102 milli m
V = Voltmeter 10° micro p
A= Ammeter 10° nano n
em

The IEE
MichaekFarada
SIPaLCM MEN
Stevenage Herts
SGI 2AY.
United Kangdo

ISBN 0 86341