1.

1 Installation dimensions
CF805T Series User’s All following annotation dimensions’ units are millimeter (mm).

Manual
609AH

Safety Precautions
For your safe use of this instrument be sure to comply with the
following safety precautions. If the instrument is used in a manner
not specified in this manual, the protection provided by the
instrument may be impaired. We assume no responsibility for the
customer‘s failure to comply with these requirements.

Do Not Operate in the following places

1．Do not exposed to the sun's rays.
2．Temperature or humidity exceed the planned.
3．Corrosive or flammable gas.
4．Highly dense dust, salt or metal powder.
5．The situation that could be spattered by water or oil and chemical 2. Wiring
liquid.
6．Direct tremble or shock.
Warning
7 ． Do not operate the instrument in the presence of flammable
 To prevent bad connection, please carefully tighten the screws
liquids or vapors. Operation in such an environment constitutes a after wiring, press the terminal connection tightly.
safety hazard. Prolonged use in a highly dense corrosive gas (H2S,
SOx, etc.) will cause a malfunction. 2.1 Wiring attention
Damage to the protection
 input signal lines should be far away from power supply line
Operating the instrument in a manner not described in this manual
and heavy load line to minimize interference
may damage the instrument’s protection.
 Shielded wires should be used to minimize noise caused by
Warning
electrostatic induction.
When installing protection and/or safety circuits such as  To minimize noise caused by electromagnetic induction, twist
lightning protection devices and equipment for the product and the measurement circuit wires at short, equal intervals.
control system or designing or installing separate protection and/or  Noise filter on the power line is recommended:
safety circuits for fool-proof design and fail-safe design of the  - Make sure the noise filter is correctly grounded
processes and lines that use the product and the control system,  - Make sure the wiring between the output side of the noise
the user should implement these using additional devices and filter and the power supply terminal is the shortest
equipment. - do not install the fuse, switch, etc. on the output side of the
If you are replacing parts or consumable items of the product, noise filter, otherwise it will reduce the effect of the filter
make sure to use parts specified by our company.  No fuse inside this instrument. External fuse with specifications

This product is not designed or manufactured to be used in below is recommended:

critical applications that directly affect or threaten human lives.  Connecting the input wires in parallel with other devices can

Such applications include nuclear power equipment, devices using cause signal degradation, affecting all connected devices.

radioactivity, railway facilities, aviation equipment, air navigation

2.2 Input
facilities, aviation facilities, and medical equipment. If so used, it is
the user’s responsibility to include in the system additional  4-wires load cell
equipment and devices that ensure personnel safety.
Do not modify this product.

1. Installation

Warning
2.3 Intelligent sensor
Be sure to turn off the power supply to prevent electric shock or instrument
failure

P-1 P-2 P-3 P-4

 Display screen is divided into the following picture:
1 main screen
Display
2 2 configuration screen
Window
3 help screen
4 prompt screen
Power
3 Hold key to turned on or off
key

2.4 Output ENTER Press key to setting or the next layer menu

EXIT Press key to exit or return to the menu

HELP Press key to display the helpful information

PICTURE Press keys to change display state of details

Functi In the measurement condition, peel them In the

 Switch input wiring diagram： 4 on condition of setting
key In the display parameters symbol，move the cursor
down or reduce the value
In the measurement condition, short press to reset
measured value，press key more than 2second to
Reset peak value and valley value
In the display parameters symbol，move the cursor
down or reduce the value
Move the cursor to the left or move the cursor to the
description page

Move the cursor right or move the cursor to the

specification.
Charging Meter in the use of the power adapter to charge this
indicator indicator light, brightness reaction charging current
5
When the instrument is turned on, the indicator light
Power indicator
is bright.Flashing indicates that it is in standby mode
commu RS232 or RS485 communication interface, support
 Switch output wiring diagram:
nication TC-ASC protocol or RTU MODBUS protocol
Output Digital
6 Nulling、Taring etc
port input
Digital
External control
output
Power adapter
7
port

4. Parameter Tables

1st Parameter group：Alarm output control parameters

★ Power supply range of VCC is 9~32VDC Group symbols Setting Range Default Addr.
H:Upper limit L:Lower limit
BH:Biased upper limit BL:Biased

3. Operations
lower limit ABH:Absolute biased
upper limit ABL: Absolute biased H:Upper
Alarm mode 02H
lower limit PH:Standby upper limit limit
PL: Standby lower limit PBH:
■ Descriptions on Faceplate & Keys Standby biased upper limit PBL:
Standby biased lower limit
-999999~0.00000
Alarm Set Value 10000 03H
0.00000~999999
Alarm Hysterisis 0.00000~999999 0 04H
Alarm-
Alarm Delay 0~60 0 05H
1
-999999~0.00000
Alarm Bias 0 06H
Alarm 0.00000~999999
GROSS、NET、PEAK、VALLEY、
PEAK-VALLEY、PEAK-PATH、
VALLEY-PATH、Averaged GROSS、
Averaged NET、Captured Max、
Averaged
Alarm Source Captured Min、Captured Inflection-1、 07H
GROSS
Captured Inflection-2、Captured
Inflection-3、Captured Inflection-4、
Captured Inflection-5、Captured
Inflection-6
H:Upper limit L:Lower limit
Name Remarks Alarm- BH:Biased upper limit BL:Biased H:Upper
Alarm mode 08H
1 Input port 4-wires load cell 2 lower limit ABH:Absolute biased limit
upper limit ABL: Absolute biased

P-5 P-6 P-7 P-8

 lower limit PH:Standby upper limit HIST:save after CaptRUN state e by key
PL: Standby lower limit PBH: HIST:save by key action action
Standby biased upper limit PBL: HIST:save after breakdown
Standby biased lower limit Volatile single buffer
-999999~0.00000 Volatile dual buffers
Alarm Set Value 20000 09H
0.00000~999999 AutoSave Threshold 0.00000~999999 100000 99H
Alarm Hysterisis 0.00000~999999 0 0AH Show Save Warning Disabled、Enabled Enabled 9AH
Alarm Delay 0~60 0 0BH Clear All Date Disabled、Enabled Disabled 9BH
-999999~0.00000 Digital Value、0~100%、 -100%~+
Alarm Bias 0 0CH Y-Axis Style A0H
0.00000~999999 -100%~+100% 100%
GROSS、NET、PEAK、VALLEY、 Y Upper Limit -999999~999999 100000 A1H
PEAK-VALLEY、PEAK-PATH、 Y Down Limit -999999~999999 -100000 A2H
VALLEY-PATH、Averaged GROSS、 Series Color 60 colors A3H
Averaged NET、Captured Max、 Do PASS/FAIL Test Disabled、Enabled Disabled B0H
Averaged
Alarm Source Captured Min、Captured Inflection-1、 0DH Show PASS/FAIL result Disabled、Enabled Enabled B1H
GROSS
Captured Inflection-2、Captured Show Template Series Disabled、Enabled Enabled B2H
Inflection-3、Captured Inflection-4、 PASS UpperOffset 0~999999 1000 B3H
Captured Inflection-5、Captured
PASS LowerOffset 0~999999 1000 B4H
Inflection-6
Passed Range Color 60 colors B5H
Alarm-1、Alarm-1
Failed Range Color 60 colors B6H
OC1 Output and !Alarm-2、!Alarm-1 and Alarm-2、 Alarm-1 2EH
Noise Filter Points 0~1000 0 B7H
OC Alarm-1 and Alarm-2
Noise Filter Threshold 0~999999 0 B8H
Output Alarm-2、Alarm-1
Inflection Points 0~6（only in password settings 2027） 0 B9H
OC2 Output and !Alarm-2、!Alarm-1 and Alarm-2、 Alarm-2 2FH
Show Analysis Disabled、Enabled Enabled BAH
Alarm-1 and Alarm-2

2nd Parameter group：Measurement 4nd Parameter group：Inflection Analysis

protected by Security code 1111 protected by Security code 1111
Group symbols Setting Range Default Addr. Group symbols Setting Range Default Addr.
Unit Kg、Ton、g、KN、N Kg 32H
Peak、Valley、Upwards Inflection、
Zero Tracking Period 0.0~10.0 0.0 33H Inflection Type Peak 200H
Downwards Inflection
Zero Tracking Range 0~200 0 34H
-999999~0.00000
NULL Range Percent 0.00~0.99 0.10 35H Y Upper Limit 0 201H
0.00000~999999
Digital Filter 1~20 1 36H -999999~0.00000
Stable Threshold 1~200 1 37H Y Dower Limit 0 202H
0.00000~999999
ARMA Filter 1~10 1 38H X Start Port 0~19199 0 203H
-999999~0.00000 X End Point 0~19199 0 204H
PreLoad Threshold 0.00000 39H
0.00000~999999 Irrelevant to Max,Min、Before Max、
-999999~0.00000 After Max、Before Min、After Min、
PreLoad MODI 0.00000 3AH Inflection Before
0.00000~999999 X Zone Between Max Min、Before prior 205H
10 times per sec、20 times per sec、 10 times Point 1 Max
Measu Display Update Rate 3BH inflection point、After prior inflection
40 times per sec per sec point
remen
15SPS、120 SPS、240 SPS、480
t Sample Rate 15 SPS 3CH Pre Interval A 0~9999 100 206H
SPS、960 SPS、1920 SPS Post Interval B 0~9999 100 207H
-999999~0.00000 Value
PEAK Threshold -999999 3EH 0.00000~999999 1000 208H
0.00000~999999 Difference C
PEAK Hysteresis 0.00000~999999 0 3FH Value
-999999~0.00000 0.00000~999999 1000 209H
VALLEY Threshold 999999 40H Difference D
0.00000~999999 Matching
VALLEY Hysteresis 0.00000~999999 0 41H -32~32 1 20AH
Ordinal
NONE、NULL、TARE、Alarm Peak、Valley、Upwards Inflection、
Digital Input Function Permission、Display Lock、Reset NONE 42H Inflection Type Valley 220H
Downwards Inflection
PEAK,VALLEY、Capture VaitTrig -999999~0.00000
ALARM Para Unlock Disabled、Enabled Enabled 43H Y Upper Limit 0 221H
0.00000~999999
NULL at Power-Up Disabled、Enabled Disabled 101H Inflecti
-999999~0.00000
on Y Dower Limit 0 222H
0.00000~999999
Analys
3 Parameter group：Capture
nd
is
X Start Port 0~19199 0 223H
protected by Security code 1111 X End Point 0~19199 0 224H
Group symbols Setting Range Default Addr. Irrelevant to Max,Min、Before Max、
0.0~1280.0 sec After Max、Before Min、After Min、
Inflection Before
Capture Duration （restricted to sample rate，save 1.6 90H X Zone Between Max Min、Before prior 225H
Point 2 Max
mode ，pass/fail test） inflection point、After prior inflection
Capture Unit Same as UNIT、KPa、MPa、GPa MPa 91H point

Area Under Stress 1.00~9999.99 1.00 92H Pre Interval A 0~9999 100 226H

Gravitation Constant 9.7000~9.9000 9.8012 93H Post Interval B 0~9999 100 227H

-999999~0.00000 Value
Start Threshold 10000 94H 0.00000~999999 1000 228H
0.00000~999999 Difference C

≥Start Judgement、cross Start ≥Start Value

0.00000~999999 1000 229H
Start Judgement Judgement upwards、cross Start Judgeme 9CH Difference D
Judgement downwards nt Matching
Captur -32~32 1 22AH
-999999~0.00000 Ordinal
e End Threshold 0 9DH Peak、Valley、Upwards Inflection、
0.00000~999999 Inflection Type Peak 240H
≤End Judgement、cross End Downwards Inflection
Capture -999999~0.00000
Judgement upwards、cross End Y Upper Limit 0 241H
End Judgement Duration 9EH 0.00000~999999
Judgement downwards、Capture
timeout
Duration timeout -999999~0.00000
Inflection Y Dower Limit 0 242H
View Duration -1~600 sec 600 95H 0.00000~999999
Point 3
output through OC1、output through X Start Port 0~19199 0 243H
Breakdown Alarm no output 96H
OC2、no output X End Point 0~19199 0 244H
-999999~0.00000 Irrelevant to Max,Min、Before Max、
Breakdown Threshold 100000 97H Between
0.00000~999999 X Zone After Max、Before Min、After Min、 245H
Max Min
Save Mode HIST:save by AutoSave Threshold HIST:sav 98H Between Max Min、Before prior

P-9 P-10 P-11 P-12

 inflection point、After prior inflection ation Parity NONE、ODD、EVEN NONE 4AH
point ALARM Controll Disabled、Enabled Disabled 4BH
Pre Interval A 0~9999 100 246H MODBUS
Protocol TC-ASCII、MODBUS/RTU、XJC 4DH
Post Interval B 0~9999 100 247H /RTU
Value Disabled、GROSS、NET、PEAK、
0.00000~999999 1000 248H
Difference C VALLEY、PEAK-VALLEY、
Value Proactive Send PEAK-PATH、VALLEY-PATH、 Disabled 4EH
0.00000~999999 1000 249H
Difference D Averaged GROSS、Averaged NET、
Matching Captured Data
-32~32 1 24AH
Ordinal STOP bits 1、2 1 100H
Peak、Valley、Upwards Inflection、
Inflection Type Valley 260H
Downwards Inflection 6nd Parameter group：Nonlinear Correction
Y Upper Limit
-999999~0.00000
0 261H protected by Security code 1111
0.00000~999999 Group symbols Setting Range Default Addr.
-999999~0.00000
Y Dower Limit 0 262H Correction Points 0~10 0 4FH
0.00000~999999
-999999~0.00000
X Start Port 0~19199 0 263H Value-1 0.0001 50H
0.00000~999999
X End Point 0~19199 0 264H
-999999~0.00000
Irrelevant to Max,Min、Before Max、 Corrected Value-1 1 51H
0.00000~999999
After Max、Before Min、After Min、
Inflection Value-2
-999999~0.00000
0.0002 52H
X Zone Between Max Min、Before prior After Max 265H
Point 4 0.00000~999999
inflection point、After prior inflection
-999999~0.00000
point Corrected Value-2 2 53H
0.00000~999999
Pre Interval A 0~9999 100 266H
-999999~0.00000
Post Interval B 0~9999 100 267H Value-3 0.0003 54H
0.00000~999999
Value
0.00000~999999 1000 268H -999999~0.00000
Difference C Corrected Value-3 3 55H
0.00000~999999
Value
0.00000~999999 1000 269H -999999~0.00000
Difference D Value-4 0.0004 56H
0.00000~999999
Matching
-32~32 1 26AH -999999~0.00000
Ordinal Corrected Value-4 4 57H
0.00000~999999
Peak、Valley、Upwards Inflection、 Upwards
Inflection Type 280H -999999~0.00000
Downwards Inflection Inflection Value-5 0.0005 58H
0.00000~999999
-999999~0.00000
Y Upper Limit 0 281H Nonlin -999999~0.00000
0.00000~999999 Corrected Value-5 5 59H
ear 0.00000~999999
-999999~0.00000
Y Dower Limit 0 282H Correc -999999~0.00000
0.00000~999999 Value-6 0.0006 5AH
tion 0.00000~999999
X Start Port 0~19199 0 283H
-999999~0.00000
X End Point 0~19199 0 284H Corrected Value-6 6 5BH
0.00000~999999
Irrelevant to Max,Min、Before Max、 -999999~0.00000
After Max、Before Min、After Min、 Value-7 0.0007 5CH
Inflection 0.00000~999999
X Zone Between Max Min、Before prior After Max 285H
Point 5 Corrected Value-7
-999999~0.00000
7 5DH
inflection point、After prior inflection
0.00000~999999
point
-999999~0.00000
Pre Interval A 0~9999 50 286H Value-8 0.0008 5EH
0.00000~999999
Post Interval B 0~9999 50 287H
-999999~0.00000
Value Corrected Value-8 8 5FH
0.00000~999999 100 288H 0.00000~999999
Difference C
-999999~0.00000
Value Value-9 0.0009 60H
0.00000~999999 3000 289H 0.00000~999999
Difference D
-999999~0.00000
Matching Corrected Value-9 9 61H
-32~32 1 28AH 0.00000~999999
Ordinal
-999999~0.00000
Downwar Value-10 0.0010 62H
Peak、Valley、Upwards Inflection、 0.00000~999999
Inflection Type ds 2A0H
Downwards Inflection -999999~0.00000
Inflection Corrected Value-10 10 63H
0.00000~999999
-999999~0.00000
Y Upper Limit 0 2A1H mV Correction Disabled、Enabled Enabled 80H
0.00000~999999
-999999~0.00000
Y Dower Limit
0.00000~999999
0 2A2H 7nd Parameter group：Graph Display
X Start Port 0~19199 0 2A3H
protected by Security code 1111
X End Point 0~19199 0 2A4H Group symbols Setting Range Default Addr.
Irrelevant to Max,Min、Before Max、 Digital Value、0~100%、 -100%~+
Y-Axis Style 800H
Inflection After Max、Before Min、After Min、 -100%~+100% 100%
Point 6 X Zone Between Max Min、Before prior After Max 2A5H Y Upper Limit -999999~999999 100000 801H
inflection point、After prior inflection Y Down Limit -999999~999999 -100000 802H
point Enable Cursor Disabled、Enabled Enabled 803H
Pre Interval A 0~9999 50 2A6H Show Alarm State Disabled、Enabled Enabled 804H
Post Interval B 0~9999 50 2A7H NONE、GROSS、NET、PEAK、
Value VALLEY、PEAK-VALLEY、
0.00000~999999 100 2A8H
Difference C PEAK-PATH、VALLEY-PATH、
Value Graph Averaged GROSS、Averaged NET、
Averaged
Difference D
0.00000~999999 3000 2A9H Displa Series-1 Source Captured Max、Captured Min、 805H
GROSS
Matching
y Captured Inflection-1、Captured
-32~32 1 2AAH Inflection-2、Captured Inflection-3、
Ordinal
Captured Inflection-4、Captured
Inflection-5、Captured Inflection-6
5 Parameter group：Communication
nd
Series-1 Color 60 colors 806H
protected by Security code 1111
NONE、GROSS、NET、PEAK、
Group symbols Setting Range Default Addr. VALLEY、PEAK-VALLEY、
COMM Address 0~99 1 48H Series-2 Source PEAK-PATH、VALLEY-PATH、 NONE 807H
Com 2400、4800、9600、19200、38400、 Averaged GROSS、Averaged NET、
Baudrate 9600 49H
munic 57600、115200、128000、230400 Captured Max、Captured Min、

P-13 P-14 P-15 P-16

 Captured Inflection-1、Captured Inflection-2、Captured Inflection-3、
Inflection-2、Captured Inflection-3、 Captured Inflection-4、Captured
Captured Inflection-4、Captured Inflection-5、Captured Inflection-6
Inflection-5、Captured Inflection-6
Series-2 Color 60 colors 808H 10nd Parameter group：User Calibration
NONE、GROSS、NET、PEAK、 protected by Security code 1111
VALLEY、PEAK-VALLEY、
Group symbols Setting Range Default Addr.
PEAK-PATH、VALLEY-PATH、
By weight、No- weight,by load cell
Averaged GROSS、Averaged NET、 Calibration Mode By weight 64H
specifications、By smart sensor
Series-3 Source Captured Max、Captured Min、 NONE 809H
Calibration Duration 1~120 20 65H
Captured Inflection-1、Captured
Load Cell SENS 0.40000~4.00000 2.00000 66H
Inflection-2、Captured Inflection-3、
-100000~0.00000
Captured Inflection-4、Captured Zero Calibration 0.0000 67H
0.00000~100000
Inflection-5、Captured Inflection-6 User
Gain Calibration 0.00001~999999. 10.0000 68H
Series-3 Color 60 colors 80AH Calibr
Weight for Gain Cali 0.00001~999999. 100000 69H
NONE、GROSS、NET、PEAK、 ation
VALLEY、PEAK-VALLEY、 -199999~0.00000
Zero Adjustment 0 6AH
PEAK-PATH、VALLEY-PATH、 0.00000~199999

Averaged GROSS、Averaged NET、 Gain Adjustment 0.50000~2.50000 1.00000 6BH

Series-4 Source Captured Max、Captured Min、 NONE 80BH Scale Interval 1、2、5、10、20、50 1 6CH
Captured Inflection-1、Captured MAX Disp Capacity 0.00001~999999. 100000 6DH
Inflection-2、Captured Inflection-3、 Calibration Lock Disabled、Enabled Disabled 6EH
Captured Inflection-4、Captured
Inflection-5、Captured Inflection-6 11nd Parameter group：System Setup
Series-4 Color 60 colors 80CH protected by Security code 1111 or 2027
Group symbols Setting Range Default Addr.
8nd Parameter group：Bar Display Replace Password 0~999999 1111 1100H
protected by Security code 1111 Default Function 0~999999 2027 1101H
Group symbols Setting Range Default Addr. Graph Display、Bar Display、Digital
Ddfault Function Capture 1102H
Digital Value、0~100%、 -100%~+ Display、Capture
Y-Axis Style 900H
-100%~+100% 100% Color Scheme Black、White Black 1103H
Y Upper Limit -999999~999999 100000 901H Reversal Display Disabled、Enabled Disabled 1104H
Y Down Limit -999999~999999 -100000 902H Backlight Duration 0~20 min 10 1105H
Show Percent Disabled、Enabled Enabled 903H MessageBox Duration 2~20 sec 10 1106H
NONE、GROSS、NET、PEAK、 Enable KEY Beep Disabled、Enabled Disabled 1107H
VALLEY、PEAK-VALLEY、 Enable Overload Sound Disabled、Enabled Enabled 1108H
Bar
PEAK-PATH、VALLEY-PATH、 Error Suppression Time 1~30 min 3 1109H
Displa
Averaged GROSS、Averaged NET、 Data & Time 2001H
y Averaged
Bar Source Captured Max、Captured Min、 904H Show Brief Introductio Disabled、Enabled Enabled 110AH
GROSS
Captured Inflection-1、Captured
Syste Show Power Oper Hint Disabled、Enabled Enabled 110BH
Inflection-2、Captured Inflection-3、
m Show Guidance Disabled、Enabled Disabled 1112H
Captured Inflection-4、Captured
Setup AutoOFF Duration 0~120min 30 1113H
Inflection-5、Captured Inflection-6
Show KEY Lock State Disabled、Enabled Disabled 1114H
Indicator-1 Color 60 colors 980H
Backlight Normal 70~100 85 1115H
Indicator-2 Color 60 colors 981H
Backlight Dimmed 33~50 35 1116H
Lanaguage Chinese、English Chinese 1117H
9nd Parameter group：Digital Display Battery Voltage 110CH
protected by Security code 1111 Firmware Ver 110DH
Group symbols Setting Range Default Addr. S/N For read only 110EH
NONE、GROSS、NET、PEAK、 A/D Reset Counter 110FH
VALLEY、PEAK-VALLEY、 Para Reset Counter 1110H
PEAK-PATH、VALLEY-PATH、 Show Welcome Picture Disabled、Enabled Enabled 1111H
Averaged GROSS、Averaged NET、 Smart Senor Oper Resul For read only 1304H
Averaged
Digital-1 Source Captured Max、Captured Min、 A00H Smart Senor Operation NONE、Save、Load NONE 1305H
GROSS
Captured Inflection-1、Captured
Enable TEDS Disabled、Enabled Disabled 1306H
Inflection-2、Captured Inflection-3、
Enable Inflection Disabled、Enabled Enabled
Captured Inflection-4、Captured
Inflection-5、Captured Inflection-6
NONE、GROSS、NET、PEAK、 12nd Parameter group：Parameters Backup
VALLEY、PEAK-VALLEY、 protected by Security code 2027
PEAK-PATH、VALLEY-PATH、 Group symbols Setting Range Default Addr.
Averaged GROSS、Averaged NET、 Param Backup Curr Paras Disabled、Enabled Disabled 1300H
Digital-2 Source Captured Max、Captured Min、 NONE A01H eters Restore Backup Disabled、Enabled Disabled 1301H
Captured Inflection-1、Captured Backu
Restore Factory Paras Disabled、Enabled Disabled 1302H
Digital Inflection-2、Captured Inflection-3、 p
Displa Captured Inflection-4、Captured
y Inflection-5、Captured Inflection-6
NONE、GROSS、NET、PEAK、 5. Instrument picture
VALLEY、PEAK-VALLEY、
PEAK-PATH、VALLEY-PATH、 ■ Block diagram
Averaged GROSS、Averaged NET、
Digital-3 Source Captured Max、Captured Min、 NONE A03H
Captured Inflection-1、Captured
Inflection-2、Captured Inflection-3、
Captured Inflection-4、Captured
Inflection-5、Captured Inflection-6
NONE、GROSS、NET、PEAK、
VALLEY、PEAK-VALLEY、
PEAK-PATH、VALLEY-PATH、
Digital-4 Source NONE A04H
Averaged GROSS、Averaged NET、
Captured Max、Captured Min、
Captured Inflection-1、Captured

P-17 P-18 P-19 P-20

 Locking display: “display lock”
Alarm state，red is OC ON,white is OC OFF
（2）
If display “××”, All OC output is not allowed
（3） Buttons can prompt the state, if the "x" shut down the sound

（4） Communication，↑ send data，↓ receive data

（5） Time (H:M:S)

（6） Show the current state of power supply, battery and power supply state

 Graph Display

■ Functional specifications

Bar Digital
Graph Display Capture
Display Display

 Wait trigger state：display of real-time data No. Function

curve after the unit conversion
GROSS、NET、PEAK、VALLEY、PEAK （1） Default function: “BAR”
 Catching state
Display - VALLEY、PEAK -Path、VALLEY
 Waveform preview state：display the （2） channel
comment -Path、Averaged GROSS、Averaged
capture the waveform （3） Measured value
NET
 History waveform state：waveform
（4） Y-Axis Style
playback
（5） Sample period
Channel 0~4 0~1 1~4 1
（6） Sample rate
10 times per （7） Unit
Display
sec、20 times per
Update 10 times per sec same as Sample Rate
sec、40 times per
Rate
sec
Unit Kg、T、g、KN、N Same as UNIT、KPa、MPa、GPa
 Bra display
Alarm Alarm-1、Alarm-2 Alarm-1、Alarm-2、Breakdown Alarm
1 capture the peak valley value record: 167
largest group, keep when power supply drop

2 capture data:

Record —— Maximum 6144 points, keep when power

supply drop

3, When “Save Mode” be set “Volatile single

buffer” or “Volatile dual buffers”,record data
can not hold

■ Picture and function description

 Title

No. Function

（1） 2 a.m. alarm percent

No. Function （2） Measured percent

Default function: “BAR” （3） Sample rate

（1） the weighing value is in motion/variation: Blink between “BAR” and （4） Measured value

“unstable” （5） Series-N Source and Unit

P-21 P-22 P-23 P-24

 automatically to the maximum by hold down the DOWN key
 Digital display  Display “ capturing ” or “ waveform preview ”， waveform can be adjusted
automatically to the minimum by hold down the DOWN key
 Display “capturing ”，press EXIT key to end capturing

 Capture list

No. Function

（1） Alarm state

（2） Measured value

（3） Alarm state and alarm mode

（4） Sample rate

（5） Digital-N Source and Unit

No. Function

 Capture display （1） Record data

 Setting parameters

No. Function

（1） Default function: “Capture”

（2） channel

（3） Measured value  Security Code

（4） Y-Axis Style 1. In measurement mode，press ENTER key to enter “Set Password”.

（5） Capture unit 2. Modify the value to 1111 by pressing UP, DOWN, LEFT, RIGHT keys
3. Press the ENTER key to save the Security Code,then Instrument display Setting
（6） Capture rate
picture
（7） Capture state
 Setting parameters
1. Instrument display Setting picture
 Function
2. Modify the cursor position by pressing UP、DOWN keys.
 Capture state is divided into four display status, wait trigger, capturing, waveform
3. Short press the ENTER key to enter the parameter list or child parameters
preview, history waveform
GROUP
 View Duration must be set to 0 when you want to see history waveform
4. In parameters goup，Short press UP、DOWN keys to modify the cursor position.
 Function key
5. Short press ENTER key to enter parameter value mode.
 Display“capturing ”or “waveform preview”，press UP key to restart wait trigger. 6. Modify the parameter value by pressing UP, DOWN, LEFT, RIGHT keys.
 Display “waveform preview”，press DOWN key to save capture data 7. Short press 2 times to save the change value.
 Display “ capturing ” or “ waveform preview ”， waveform can be adjusted 8. Press EXIT key to exit out of change when you don’t want to modify the

P-25 P-26 P-27 P-28

 parameter value.  The filtering process ArmA→FLtr
9. In setting password，short press EXIT to exit setting picture.
10. In child parameters group，hold down the EXIT key to exit setting picture.
 Display Update Rate：Display refreshing rate
 In“setting”、
“parameters group”picture，you can press HELP key to view button
 PreLoad Threshold：Measurement correction threshold
or parameters description.
 PreLoad MODI：Measurement correction value

If measured value ＜ PreLoad Threshold，gross value = raw value

If measured value ≥ PreLoad Threshold，gross Value = raw value + PreLoad MODI

6. Calibration ■ 7.1.3 Sampling rate

 Sample Rate：Sampling & output rate, 15、120、240、480、960、1920 times per second

Calibration should be performed at first use or after any change made to measurement
7.2 Peak value and Valley value detection
apparatus, especially after replacing load cell .

6.1 Calibration method  Peak value and valley value detection

 Shortcut to calibration parameters

1. Press the ENTER key in measurement mode
2. Modify the value to 1111 by pressing UP, DOWN, LEFT, RIGHT keys
3. Press the ENTER key to save the password
Example：the range of sensor 0~10000kg , load cell sensitivity 2.00010 mV／V
 By weight
4. Zero Calibration：

Press the ENTER key to“Zero Calibration”，，input signal value is displayed (in millivolts) and
★ Peak value and Valley value will be automatically refreshed at every
refresh constantly
threshold crossing
Clear out weighing platform，Press the ENTER key to confirm zero signal when the display is
stable ★ In peak detection status, the Peak process value is always updated
★ In measurement mode，hold DOWN key for more than 2 seconds to reset the
5. Gain Calibration：
peak value and valley value to current gross value
Press the ENTER key to“Gain Calibration”，input signal value is displayed (in millivolts) and

refresh constantly
7.3 Digital input

Add weights A to the platform

 Digital Input(K1) Function：
Press the ENTER key to confirm gain when the display is stable No. symbols Item
6. Weight Calibration： 0 NONE No function

Press the ENTER key to“Weight for Gain Cali”, ，modify the value to weights A by pressing Nulling，peak value、valley value、peak process value and
1 NULL
UP, DOWN, LEFT, RIGHT keys Valley process value also be reset to zero.
2 TARE Taring
Press the ENTER key to save weight。
Alarm output function is valid when the digital input is active.
 No- weight,by load cell specifications Alarm
3 Otherwise, alarm output status is locked and unit indication LED
Permission
4. Sensitivity Calibration： blinks as a hint.
when the digital input is active, display is locked to current state.
Press the ENTER key to“Load Cell SENS”, ，modify the value to 2.0001 by pressing UP, 4 Display Lock
GROSS and NET indicator LED blink as a hint
DOWN, LEFT, RIGHT keys Reset Peak value 、valley value、peak process value and valley process
5
5. Weight Calibration： PEAK,VALLEY value be reset to current gross value when digital input is active
Press the ENTER key to“Weight for Gain Cali”, ，modify the value to weights A by pressing 6 Capture VaitTrig Enter and start capture

UP, DOWN, LEFT, RIGHT keys

7.3 Alarm outputs
6. Manual calibration can further be corrected by “Zero Adjustment” and “Gain Adjustment”

Each alarm output has 6 parameters in 1st parameter group. These parameters can be changed

only when parameter “ALARM Para Unlock” is set to ON

7. Instructions on Functions & Parameters  Upper limit alarm  Lower limit alarm

7.1 Measurement
■ 7.1.1 Zero tracking , Nulling and Motion/Variation Detection

 Zero Tracking：Zero tracking range, in the unit of scale interval. If the measurement
weight is within the zero tracking range for more than or equal to zero

tracking time, the reading will be tracked to zero. If this parameter is

 Upper alarm with deviation  Lower alarm with deviation
set to 0, zero tracking function will be turned off

 NULL Range： In measurement mode, if the measured value is in nulling range of

maximum capacity “ MAX Disp Capacity ” , the display value can be
nulled to zero by ZERO key or digital input k1（if parameter di0F be se to
Zero）. However,。
 Stable Threshold： When the fluctuation of the measured value in 1 second exceeds set
value, in the unit of scale interval, the measurement is unstable, and
operations like Nulling, Taring and Zero Tracking cannot be fulfilled。
 Absolute upper limit alarm  Absolute lower limit alarm
■ 7.1.2 Filtering
with deviation with deviation
 Digital Filter： The setting range is 1~20. Bigger value brings about strong filter effect
but slower response. Value of 1 means inertial filtering function is turned off

 ARMA Filter： Response time is better than inertial filtering but filtering effect is not so
strong. Value of 1 means moving averaging function is turned off

P-29 P-30 P-31 P-32

 7.6 Capture
Working mode
1） Continuous measurement
The instrument is equivalent to a standard gauge or module, can realize measurement,
alarm, communication function, can also view the measured real-time curves, no capture
process requirements, at this time without setting parameters related to capture only
according to the actual usage set related parameters measurement, alarm,
communication and so on
 Upper limit alarm under  Hysteresis  Pay attention to the application mode as does not affect the standard of alarm
armed state functions, should be "capture Settings" parameter set of "fault alarm output" should be set
to "output”
Standby lower limit Upper limit 2） Result judgment
Requiring meter automatically determine a measure in the process of peak and valley
value, fracture values, etc. Is suitable for workpiece stamping monitoring, hammer,
experiment machine, etc. This way the general measurement speed is quick, upload the
judgment.
Work process: wait trigger - > meeting Start Judgement - > start capture- > meeting End
Judgement - > end capture - > display waveform preview (if set up a fault alarm output,
the synchronous output relay) or wait for the trigger...
In this application mode, instrument related parameters can be set up as follows:
 OUT —— Alarm Set Value Group symbols Items
 HyA —— Alarm Hysterisis Measure
Sample Rate 1920SPS
 Av —— Alarm Bias ment
Capture Duration
7.4 Communication Start Threshold
Start Judgement
Communication interface RS232, RS485, optional support TC ASCII and Modbus RTU protocol End Threshold
(through the parameter Settings). End Judgement According to the actual application Settings
Instrument factory communication default mode, the instrument to receive instruction and Capture
View Duration
respond from PC communication, each received an instruction corresponds to return to the Breakdown Alarm
corresponding data to the PC.
Breakdown
Independently by instruments such as the need, has been continuously active send data to the
Threshold
PC (no longer respond to receive instruction), can be "communication Settings" in "native"
Save Mode Volatile single buffer or Volatile dual buffers
unsolicited parameter to fix from "disabled" to other numerical (can choose different sending data
 The user can be read in waveform preview or waiting for communication state trigger the
content).
last peak and valley value capture process.
 Instrument continuously active to send data only support TC ASCII protocol, if the instrument is
3） Long interval process record and result judgment
RS485 communication interface, it will no longer respond to receive instructions and take the
Work process: wait trigger - > meeting Start Judgement - > start capture- > meeting End
initiative to send the baud rate of not less than 9600 BPS.
Judgement - > end capture - > display waveform preview - > PC read capture data - > end
 Initiating mode, send data cycle is related with sample rate and Baudrate, specific
waveform preview - > wait trigger
corresponding relationship is as follows (in the table values for "every N time measuring active
send a data communications") :
Group symbols Items
Measure
Sample Sample Rate
ment
rate 15 sps 120 sps 240 sps 480 sps 960 sps 1920 sps Capture Duration
Start Threshold
Baudrate Start Judgement
According to the actual application Settings
End Threshold
9600bps 1 2 3 6 12 24
End Judgement
Capture
19200bps 1 1 2 3 6 12 Breakdown Alarm
Breakdown
38400bps 1 1 1 2 3 6
Threshold

57600bps 1 1 1 1 2 4 View Duration Value should be greater than the PC read capture data
Save Mode Volatile single buffer or Volatile dual buffers
115200bps 1 1 1 1 1 2
4） Short interval process record and result judgment
128000bps 1 1 1 1 1 2
Work process: wait trigger - > meeting Start Judgement - > start capture- > meeting End
230400bps 1 1 1 1 1 1 Judgement - > end capture - > display waveform preview - > PC read capture data - > end
waveform preview - > wait trigger

7.5 Linearization Function Group symbols Items

This function can be used to tackle the non-linearity of measurement apparatus, for Measure
Sample Rate 1920SPS
ment
example, the non-linearity of load cell.
Capture Duration
Start Threshold
Start Judgement
According to the actual application Settings
End Threshold
Capture
End Judgement
Breakdown Alarm
View Duration 0 or -1
Save Mode Volatile dual buffers

8. Specifications

For measured value less than Corrected Value-1, Linearization is performed according to the ■ General Specifications
slope rate between Corrected Value-1~ Corrected Value-2. Items Specifications
Input：AC 90~260V，50Hz or 60Hz
For measured value greater than Corrected Value-10, Linearization is performed according to Power adapter
Output：DC 12V/2A，the outside interface is negative
the slope rate between Corrected Value-9~ Corrected Value-10 Continuous use time about 18 to 36 hours, related to the
Built-in battery
use

P-33 P-34 P-35 P-36

 Charging time about 4 ~ 8 hours
Standby time is about 4 ~ 8 days
Life not less than 1000 times full charge and discharge cycle
Insulation resistance ≥100MΩ（500V DC MEGA）。
Insulation strength 2000V AC （Condition：50/60Hz，1minute）

IEC61000-4-2（Electrostatic discharge)，Ⅲ class

ECCM IEC61000-4-4（EFT），Ⅲ class
IEC61000-4-5（Surges），Ⅲ class
Protection grade IP65（front panel protection）（GB/T42-2008）

■ Input specifications

Items Specifications
Input signal 4-wires load cell
Load Cell sensitivity 0.1uV / d
Zero Adjustment －10～10 mV
Gain Adjustment 1 ～12 mV
Sample rate 15、120、240、480、960、1920SPS
Accuracy ±0.05%F•S（sample rate：15SPS）
Span Drift ＜ 10 ppm／℃
Resolution 1／100000
Digital input 1 channel
■ Output specifications

Items Specifications
Load cell excitation power DC 5V±2%，100mA（MAX）
supply
Alarm Output Two output channel of Open Collector, ≤35mA
■ Specifications on Optional Accessories Parts

Items Specifications

M1 RS232，Modbus-RTU and TC ASCII Photo-isolation

Communition Commands with weight

value: response time less
M2 RS485，Modbus-RTU and TC ASCII
than 500μs
V0 NULL
Battery
V1 built-in battery
T0 NULL
Clock
T1 RTC

P-37 P-38 P-39 P-40