PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS

SKILLION 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT ROOF AREA FOOTING SIZE (PC CAST IN) SLAB THICKNESS (PC FIXING ON TOP)
ALTERNATIVE 76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT 8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN UNREINFORCED SLAB
B PP B PP B
90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m² 600 x 600 x 600 DEEP MASS CONCRETE 100mm MIN REINFORCED SLAB
100 x 50 x 2.0 SHS PATIOS (OR LARGER COLUMN FOR
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² 700 x 700 x 700 DEEP MASS CONCRETE N/A
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 700 x 700 x 700 DEEP MASS CONCRETE
DOME TRUSS FREESTANDING OR N/A
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT
PP PP Ø300 x 1200 DEEP MASS CONCRETE PILE

STEEL PATIO OR CARPORT

ALTERNATIVE PP PP PP PP
B B B 150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS

TRUSS
E N G I N E E R P E R T H
GABLE TRUSS PP
(GABLE ROOF - WIND REGION A)
PP PP
PP PP
PP PP
PP
Suite 26, Upper Floor, 443 Albany Hwy, Victoria Park, WA 6100
p: 08 6424 8129 e: [email protected]
w: www.engineerperth.com
B B B B
PP
BEAM

PURLIN

EXISTING
3m MAX BEAM SPAN FOR HOUSE
PC PC PC PC
FASCIA CONNECTION
PF
GENERAL NOTES
PF PF PF
STRUCTURAL SET
PF

CONCRETE SHEET DRAWING

1. CONCRETE FOOTING TO BE OF GRADE 20MPa, MAX AGGREGATE SIZE 20mm AND SLUMP 100mm.
TYPICAL ELEVATION AT TRUSS (TR) - 1:100
2. COLUMN TO BE CAST INTO FOOTING. COLUMN MAY BE FIXED TO CONCRETE SLAB AS SHOWN ON END ELEVATION S1.1 TERRAIN CATEGORY 3 (FS) - 1kN MAX POINT LOAD
DETAILS.
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE.
3. ROOF AREA = FB SPAN/2 x TR SPAN S1.2 TERRAIN CATEGORY 3 (FS) - NO POINT LOAD

EXISTING FASCIA & GUTTER S1.3

3m MAX BEAM SPAN FOR TERRAIN CATEGORY 2 (FS), 2.5 (FS, PS), 3 (PS, NS) - 1kN MAX POINT
MEMBERS
(ADD FASCIA PLATE) FASCIA CONNECTION LOAD
1.GENERAL
a) STEEL GRADE TO BE 350MPa FOR ALL PATIO TUBE MEMBERS AND DURAGAL 450MPa FOR
S1.4 TERRAIN CATEGORY 2 (FS), 2.5 (FS, PS), 3 (PS, NS) - NO POINT LOAD
ALL RHS/SHS MEMBERS U.N.O. 1,000 1,000
PP FOR STEELWORK"
PP PP PP PP OF PP PP PP TRUSS
b) TABLE 3.4.4.7 "PROTECTIVE COATINGS OF THE BUILDING CODE MAX MAX
S1.5 TERRAIN CATEGORY 2 (PS, NS), 2.5 (NS) - 1kN MAX POINT LOAD
AUSTRALIA TO BE FOLLOWED FOR THE TREATMENT OF ALL STEELWORK AND FASTENERS.

3m MAX BEAM SPAN

c) ALL SCREWS TO BE TO No.10 x 16, No.12 x 20 OR No.14 x 20 TEKS, AS PER DETAILS. S1.6 TERRAIN CATEGORY 2 (PS, NS), 2.5 (NS) - NO POINT LOAD

END ELEVATION
(COATING TO SUIT PPEXPOSURE CLASSIFICATION)
2. BEAMS OVER 6m SPAN MAY BE PRECAMBERED TO AVOID NOTICEABLE DEFLECTION.
S2.1 BEAM SECTIONS / OPTION WITH POST SETBACK
BEAM

BEAM

BEAM

BEAM
3. IF EXISTING HOUSE HAS TRUSSED ROOF & EAVES OVERHANG, STRENGHEN OVERHANG TO ACCEPT
LOADS FROM PATIO, AS REQUIRED BY TRUSS MANUFACTURER.
EXTENSION OF S2.2 PURLIN PC BASE FIXING DETAILS
4. ROOF CLADDING - METAL SHEET U.N.O.
PP PC & PEB
S2.3 PC FIXING TO RETAINING WALLS
FABRICATION AND ERECTION SETBACK OF
PC ON PEB OR TRUSS EXISTING
1. AS4100 TO BE FOLLOWED FOR ALL STEELWORK. S2.4 PATIO CONNECTIONS / RAISED
HOUSEGABLE OPTION
2. BUILDING CODE OF AUSTRALIA AND ALL RELEVANT STANDARDS TO BE FOLLOWED FOR ALL
PP
STEELWORK. S2.5 PATIO CONNECTIONS / EXTENSIONS / FIXING BRACKETS
3. STEELWORK COATING TO BE SELECTED AS PER EXPOSURE CLASSIFICATIONS.
4. ALL MEMBERS AFTER SITE WELDING TO BE TREATED WITH COLD GALVANIZING PAINT. PATIO COLUMN & PF PF S2.6 PATIO ROOF RISER AND OVERLAP OPTIONS
5. ALL HOLLOW SECTIONS TO BE SEALED AT OPEN ENDS. PATIO FOOTING)
S2.7 PATIO CONNECTIONS / EXTENSIONS
INSULATED ROOF TRUSS
1. MAX ALLOWABLE SPAN OF ALL MEMBERS TO BE REDUCED BY 20% FOR INSULATED PANELS WEIGHING S2.8 FREESTANDING / ATTACHED ELEVATIONS
TYPICAL PLAN
UP TO - 1:100
0.15kPa MAX. U.N.O. END ELEVATION - OPTION POST EXTENSION/POST SETBACK
S2.9 TRUSS DETAILS
NOTES: 2. SELECT INSULATED PANEL TO SUIT SPAN.
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS.
DESIGN CRITERIA S2.10 PATIO ENCLOSURE: SINGLE SKIN & SOLARSPAN INSULATED
- STEEL GR350 FOR 76 x 38 x 1.2 / 1.6 MEMBERS, & GR450 DURAGAL FOR OTHERS U.N.O.
1. WIND REGION TO AS 1170.2 = A. IMPORTANCE LEVEL 2 TO BCA. WALLS (OPTION)
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. TRUSS
- OPTION 2. SITEEXTENSION
WITH CLASSIFICATION
ANDA,SETBACK
S, M, OR HOF
TOPC
AS2870
ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE. S2.11 USE OF TIMBER POSTS / BUSH POLES
3. MAX DEAD LOAD DEFLECTION: - TRUSS = SPAN
250
- PURLINS = SPAN S3.1 DIMENSIONS WHEN ADDING SOLAR PANELS ON ROOF
180 BEAM
4. TOTAL DEAD LOAD 0.1kPa, TOTAL LIVE LOAD 0.15kPa. S3.2 DIMENSIONS FOR ECODECK/SOLARSPAN TYPE ROOF OR
PE & CRITERIA
5. GABLE PITCH TO BE FROM 12 TO 30° MAX. PURLIN TIMBER/GYPROCK CEILINGS
S DESIGN APPLIES TO TO
6. REFER A REGULAR PATIO ATTACHED
MANUFACTURER'S TO A
SPECIFICATIONS FOR FIXING OF ROOF CLADDING.
ULAR HOUSE.7. REFER TO BUILDER'S DETAILS FOR FIXING OF FLASHING AND GUTTERS. SETBACK OF
SIGN LOADINGS ARE AS/NZS 1170. PC ON BEAM
8. NO CEILING LOADS INCLUDED IN DESIGN. NO POINT LOADS ALLOWED.
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN
9. ADDITIONAL TIE DOWNS FOR THE EXISTING ROOF MAY BE REQUIRED WHEN:
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS
- CONNECTED TO AN EXISTING BUILDING
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED.
ARTURE FROM - THE EXISTING
THESE ROOF CLADDING
SPECIFICATIONS VOIDS IS STEEL SHEETING
THE PP - PATIO PURLIN
TIFICATION. - THE PATIO BEAM (PB) SPAN EXCEEDS 6.0m END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM PF - PATIO FOOTING
- WHEN
EXISTING HOUSE HASFIXED
TRUSSTOROOF
AN EXISTING
& EAVESTILED ROOF
OVERHANG, PC - PATIO COLUMN
- WHERE CONNECTED
ENGTHEN OVERHANG TO A STEEL
TO ACCEPT LOADS FROMTRUSSED
PATIO AS ROOF TR - TRUSS
IT IS MANUFACTURER.
UIRED BY TRUSS THE BUILDER'S RESPONSABILITY TO CONTACT THE ENGINEER FOR PROPER ADVICE IF UNSURE. B - BEAM
10. PATIO BUILDER TO ENSURE THE EXISTING HOUSE ROOF IS ADEQUATELY TIED DOWN TO RESIST Approved by:

COPYRIGHT
UPLIFT. IF ROOF IS NOT ADEQUATELY TIED DOWN CONTACT THE ENGINEER. IF UNSURE CONTACT THE
COPYRIGHT
Address: Address:
STEEL PATIO OR CARPORT (COMBINATION) Approved by:

ENGINEER. G A Gaynor MIEAust, CPEng, NER

11. FREESTANDING PATIOS ARE DESIGNED AS OPEN ON 4 SIDES AND MUST NOT BE ENCLOSED WITHOUT Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920
FURTHER ENGINEERING VERIFICATION.
without thewithout
permission of Engineer
of Perth Pty Perth
Ltd. Contractor shall 12 (15/07/20)
Revision:
AND the permission Engineer Pty Ltd. Contractor shall
11 (01.07.19)
Revision:
12. CONNECTIONS INCLUDE BRICK VENEER, STEEL STUD FRAME TIMBER STUD FRAME HOUSING.
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
[email protected]
p: 08 8129 e: [email protected] signature from an authorised Engineer Perth signatory.
signature from an authorised Engineer Perth signatory.
1:100 S1.1
Scale: Scale: Sheet: Sheet:
w: www.engineerperth.com.au
w: www.engineerperth.com.au
ionGSPublisherVersion
0.0.100.100 0.0.100.100
 CRANKED BEAMS (CB) MAX SPAN TABLE - 1kN MAX POINT LOAD PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS(PC) BASE FIXINGS
COLUMN

RAFTER / BEAM SKILLION

76 x 38 x 1.2 76 x 38 x 1.6 76 x 38 x 2.0 90 x 38 x 1.2 76xx3.0
38 x 1.2100
90 x 38 x 1.6
75 x 50 PATIO
x 50TUBE 100 x 50 xTO
75 x 50 x 1.6
x 1.6 2.03000 MAX
75 x 50 x 2.0100 xHEIGHT
50 x 3.0 ROOF150
150 x 50 x 2.0 AREA
x 50 x 3.0 FOOTING SIZE (PC CAST IN)
ROOF AREA SLAB
FOOTING SIZE THICKNESS
(PC CAST IN) (PC FIXING ON THICKNESS
SLAB TOP) (PC
SPACING ALTERNATIVE
PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE
DURAGAL76 xRHS DURAGAL RHS
DURAGAL
38 x 1.6 PATIO TUBE DURAGAL RHS
RHS DURAGALTO RHS3600DURAGAL
MAX HEIGHTRHS DURAGAL RHS DURAGAL RHS FIXING ON TOP)
8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN UNREINFORCED SLAB
1800 3400 PP
4800 B 4400 5100 PP 4700 4400 B 5600 5900 B
6300 5000 7100 8800 8800 8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN
90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m² 600 x 600 x 600 DEEP MASS CONCRETE 100mm MIN REINFORCED SLAB
UNREINFORCED SLAB
2400 3300 4000 4300 4200 4600 4200 4500 5100 100 x 50 x 2.05400
SHS 5700(OR LARGER 6400
PATIOS COLUMN FOR 8100 8200
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² DEEP MASS600
14m²
700 x 700 x 700 x 600 x 600 DEEP MASS CONCRETE
CONCRETE N/A 100mm MIN REINFORCED
3000 3200 3700 4000 3900 4300 3900 4200 4700 5000 5300 6000 7500 7700 SLAB
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 700 x 700 x 700 DEEP MASS700CONCRETE
x 700 x 700 DEEP MASS CONCRETE
3600 3100 3500 3800 3700 4100 3700 4000 4400 4700 5000 5600 7000 7400 20m² N/A
DOME TRUSS FREESTANDING OR N/A
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT
4200 ALTERNATIVE
3000 3300 PP PP
3600 PP 3500 PP 3900 PP PP
3500 3800 4200 4400 4700 5300 6700 7100 Ø300 x 1200 DEEP MASS 700 x
CONCRETE 700 x 900
PILE DEEP MASS CONCRETE
150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS FREESTANDING OR N/A
B B B
NOTE: FOR SOLARSPAN TYPE ROOF OR TIMBER/GYPROCK CEILINGS REDUCE THESE SPAN VALUES BY 20%. SOLARSPAN TO BE INSTALLED TO MANUFACTURER'S SPECIFICATIONS Ø300 x 1200 DEEP MASS CONCRETE PILE

RAFTER BRACKETS TO BE FIXED

TRUSS
TO EVERY 3RD EXISTING RAFTER A EDGE BEAMS (PEB) MAX SPAN TABLE - 1kN MAX POINT LOAD
(1800 CRS MAX) PP PP PP PP
GABLE TRUSS PP EXISTING RAFTERS PP 100 x 50 x 1.6 100 x 50 x 2.0 100 x 50 x 3.0 150 x 50 x 2.0 150 x 50 x 3.0 150 x 50 x 4.0 150 x 100 x 4.0 C20015 C20019 C25019
PP PP
DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS LYSAGHT G450 LYSAGHT G450 LYSAGHT G450
B B B B
PATIO WIDTH MAX = 4000 5400 6200 6700 8400 9300 9700 10900 8100 9000 9600
PP EXISTING WALL
PATIO WIDTH MAX = 6000 4500 5200 6000 7000 8400 BEAM 8800 10000 7200 8100 8700
PATIO WIDTH MAX = 8000 3900 4500 5400 6100 7700 PURLIN 8200 9000 6600 7300 8100
PATIO WIDTH MAX = 10000 3500 4100 5000 5500 7000 7700 8600 6100 6800 7500
NOTE: FOR SOLARSPAN TYPE ROOF OR TIMBER/GYPROCK CEILINGS REDUCE THESE SPAN VALUES BY 20%. MAXIMUM CANTILEVER OF
EXISTING
PEB/GT/CB FROM OFFSET PC TO GABLE END TRUSS IS 15% OF THE BACKSPAN (MAX 1000) HOUSE
PC PC PC PC 3m MAX BEAM SPAN FOR
FASCIA CONNECTION

EXTENDED SPAN TRUSS SPAN AS PER SPAN TABLE

PF PF PF PF

TRUSS SPAN AS PER SPAN TABLE

FROM EXISTING BRICKWORK

EXISTING FASCIA PLATE PURLIN (PP) MAX SPAN TABLE - 1kN MAX POINT LOAD
W/ NEW FASCIA PLATE PF

FROM EXISTING FASCIA

MAX PURLIN 76 x 38 x 1.2 76 x 38 x 1.6 76 x 38 x 2.0 90 x 38 x 1.2 90 x 38 x 1.6 75 x 50 x 1.6 75 x 50 x 2.0 100 x 50 x 1.6 150 x 50 x 3.0
TRUSSES OR CRANKED BEAM SPACING PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS
SPACING TO BE 4500 MAX
1200 3700 4500 4800 4500 5300 4800 5200 6600 9500
C
TYPICAL ELEVATION C
AT TRUSS (TR) - 1:100 END ELEVATION
1800 3400 4400 4700 4300 5100 4700 5000 5600 8800
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE. -25%
FASCIA BEAM 2400 3300 4000 4300 4100 4600 4200 4500 5100 8200
3000 3200 3700 4000 3m MAX3900
BEAM SPAN FOR4300 3900 4200 4700 7700
EXISTING FASCIA & GUTTER
(ADD FASCIA PLATE) MAXIMUM PURLIN FASCIA CONNECTION
GUTTER OVERHANG AT 600 (OR 20% OF THE BACKSPAN - WHICHEVER IS LESS) 900 (OR 20% OF THE BACKSPAN - WHICHEVER IS LESS)
GABLE END
1,000 CEILINGS
NOTE: FOR SOLARSPAN TYPE ROOF OR TIMBER/GYPROCK 1,000 REDUCE TOTAL SPAN VALUE BY THESE PERCENTAGES (OR HALVE THE PURLIN SPACING)
1.8m MIN

TRUSS

INCL. IN TOTAL
RAFTER SPAN
PP PP PP PP PP PP PPPURLINS
PP MAX MAX
FULLY WELDED OUTRIGGERS REFER TO PURLIN MAX SPAN TABLE
TO REFER TO NOTES

3m MAX BEAM SPAN

END ELEVATION
PP FIX FASCIA PLATE
W/ SADDLE BRACKET GABLE TRUSS (GT) MAX SPAN TABLE
BEAM
BEAM

BEAM

BEAM

BEAM
RAFTER BRACKET EACH SIDE BOUNDARY
OF FB FIXING POSITION LINE EXTENSION OF TRUSS MEMBERS
PURLIN SPAN TO RHS SECTIONS REQUIRED
PP PC & PEB 6000 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. 400 TOP
UNLESS FASCIA PLATE EXTENDED TO SETBACK OF OR BOTTOM CHORD EXTENSIONS.
CORNER AND A RAFTER BRACKET STEEL COLUMNS LOCATION PC ON PEB OR TRUSS EXISTING
INSTALLED AT THE EXISTING HIP RAFTER. (IF TRUSS EXTENDED TO BOUNDARY) 8000 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. NO
HOUSE
EXTENSIONS.
PP
TYPICAL PLAN 76 x 38 x 1.6 PATIO TUBE 8000 (WITH FOR TOP / BOTTOM CHORD EXTENSIONS TO 1000mm,
NOTES: OR
GT/CB 1000 MAX FOR USE 100 x 50 x 2.0 RHS.
- PROVIDE COLUMNS AT EACH TRUSS FOR FREESTANDING ROOF. PATIO COLUMN & PF PF 100 x 50 x 2.0 RHS DURAGAL
LENGTH TO BE 6000 MAX EXTENSIONS) OTHERWISE AS PER 8000 SPAN ABOVE.
- FULLY WELDED OUTRIGGERS TO TRUSS @ 1200 CRS MAX. TO REFER TO SECTION B. PATIO FOOTING)
- ROOF PITCH TO BE FROM 12 TO 30° MAX. 10000 TOP CHORD 76 x 38 x 1.6 RHS Gr350 - NO EXTENSIONS.
- WHERE NO WALL OR ROOF FIXING ON SIDE OF PATIO, REFER TO FREESTANDING DETAIL. TRUSS WEBS 76 x 38 x 1.6 RHS OR 30 x 1.6 SHS. BOTTOM
- OPTION: RAFTER BRACKETS TO BE FIXED TO EVERY 2ND EXISTING RAFTER (1200 CRS MAX). CHORD 100 x 50 x 2.0 RHS. NO EXTENSIONS.
TYPICAL PLAN - 1:100 BEAM SPACING PATIO PURLIN END ELEVATION - OPTION POST EXTENSION/POST SETBACK
NOTES: CL (REFER TO TABLE) CL
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN
BEAM SPACING TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS.
BEAM SPACING PATIO COLUMN (PC) PATIO CONDITIONS (TOPOGRAPHICAL FACTOR OF 1.0)
- STEEL GR350 FOR CL
76 x(REFER
38 x 1.2
TO/ TABLE)
1.6 MEMBERS, & GR450
CL (REFER DURAGALCL
TO TABLE) FOR OTHERS U.N.O.
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT TRUSS TERRAIN CATEGORY FULL PARTIAL NO
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE. SHIELDING SHIELDING SHIELDING
76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT
GT/CB
PURLINS CTRS TO 90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING
TERRAIN CATEGORY - 3
¸
REFER TO TABLE

TERRAIN CATEGORY - 2.5

SUIT CLADDING 100 x 50 x 2.0 SHS PATIOS (OR LARGER COLUMN FOR
EDGE PATIO B (REFER TO MAX SPAN 150 x 50 x 2.0 SHS AESTHETIC REASONS) BEAM TERRAIN CATEGORY - 2
BEAM PURLIN
PURLIN TABLE)
PE & CRITERIA GT/CB 90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHTPURLIN - 1kN MAX POINT LOAD
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO APATIO PATIO FOOTING
(REFER TO TYPICAL 100SETBACK
x 100 x 3.0OF
SHS (G350) TO 6000 MAX HEIGHT
ULAR HOUSE. COLUMN
SIGN LOADINGS ARE AS/NZS 1170. PC BASE FIXING PC ON BEAM
PATIO COLUMNS 150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN DETAIL) 6000 MAX
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED. GT/CB FOR FREE-STANDING STRUCTURES THE
MAXIMUM COLUMN SPACING IN EACH PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS VOIDS THE PP - PATIO PURLIN
DIRECTION IS 6 METRES. PEB - EDGE BEAM
TIFICATION.
FRONT ELEVATION FREESTANDING PLAN OPTION END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG, PC - PATIO COLUMN
PF - PATIO FOOTING
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 1:100
Scale: Sheet:
S1.1 Sheet:
S1.1
ionGSPublisherVersion
0.0.100.100 0.0.100.100
 CRANKED BEAMS (CB) MAX SPAN TABLE - NO POINT LOAD PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS(PC) BASE FIXINGS
COLUMN

RAFTER / BEAM SKILLION

76 x 38 x 1.2 76 x 38 x 1.6 76 x 38 x 2.0 90 x 38 x 1.2 90 x 38 x 1.6 75 x 50 x 1.6 75 x 50 x 2.0 76xx3.0
75 x 50 38 x 1.2100
PATIO
x 50TUBE
x 1.6 100 x 50 xTO
2.03000 MAX
100 xHEIGHT
50 x 3.0 ROOF150
150 x 50 x 2.0 AREA
x 50 x 3.0 FOOTING SIZE (PC CAST IN)
ROOF AREA SLAB
FOOTING SIZE THICKNESS
(PC CAST IN) (PC FIXING ON THICKNESS
SLAB TOP) (PC
SPACING ALTERNATIVE
PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE DURAGAL RHS DURAGAL RHS DURAGAL76 xRHS DURAGAL
38 x 1.6 PATIO TUBERHS DURAGALTO RHS3600DURAGAL
MAX HEIGHTRHS DURAGAL RHS DURAGAL RHS FIXING ON TOP)
8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN UNREINFORCED SLAB
1800 4100 B 4400 PP
4700 4700 B 5100 PP 4700 B 5000 5600 5900 6300 7100 8900 8800 8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN
90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m² 600 x 600 x 600 DEEP MASS CONCRETE 100mm MIN REINFORCED SLAB
UNREINFORCED SLAB
2400 3700 4000 4300 4300 4600 4200 4500 5100 100 x 50 x 2.05300
SHS 5700(OR LARGER 6400
PATIOS COLUMN FOR 8100 8200
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² DEEP MASS600
14m²
700 x 700 x 700 x 600 x 600 DEEP MASS CONCRETE
CONCRETE N/A 100mm MIN REINFORCED
3000 3400 3700 4000 4000 4300 3900 4200 4700 5000 5300 6000 7500 7700 SLAB
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 700 x 700 x 700 DEEP MASS700CONCRETE
x 700 x 700 DEEP MASS CONCRETE
3600 3200 3500 3800 3700 4000 3700 3900 4400 4700 5000 5600 7000 7400 20m² N/A
DOME TRUSS FREESTANDING OR N/A
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT
4200 ALTERNATIVE
3000 3300 PP PP
3600 PP 3500 PP 3800 PP PP
3500 3700 4200 4400 4700 5300 6700 7100 Ø300 x 1200 DEEP MASS 700 x
CONCRETE 700 x 900
PILE DEEP MASS CONCRETE
150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS FREESTANDING OR N/A
B B B
Ø300 x 1200 DEEP MASS CONCRETE PILE

RAFTER BRACKETS TO BE FIXED

TRUSS
TO EVERY 3RD EXISTING RAFTER A EDGE BEAMS (PEB) MAX SPAN TABLE - NO POINT LOAD
(1800 CRS MAX) PP PP PP PP
GABLE TRUSS PP EXISTING RAFTERS PP 100 x 50 x 1.6 100 x 50 x 2.0 100 x 50 x 3.0 150 x 50 x 2.0 150 x 50 x 3.0 150 x 50 x 4.0 C20015 C20019 C25019
PP PP 150 x 100 x 4.0
DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS LYSAGHT G450 LYSAGHT G450 LYSAGHT G450
B B B B
PATIO WIDTH MAX = 4000 5400 6100 6700 8400 9300 9700 10900 8100 9000 9600
PP EXISTING WALL
PATIO WIDTH MAX = 6000 4500 5200 6000 7000 8400 BEAM 8800 10000 7200 8100 8700
PATIO WIDTH MAX = 8000 3900 4500 5400 6100 7700 PURLIN 8200 9000 6600 7300 8100
PATIO WIDTH MAX = 10000 3500 4100 5000 5500 7000 7700 8600 6100 6800 7500
* NO BEAM CANTILEVER ALLOWED EXISTING
3m MAX BEAM SPAN FOR HOUSE
PC PC PC PC
FASCIA CONNECTION

EXTENDED SPAN TRUSS SPAN AS PER SPAN TABLE

PF PF PF PF

TRUSS SPAN AS PER SPAN TABLE

FROM EXISTING BRICKWORK

EXISTING FASCIA PLATE PURLIN (PP) MAX SPAN TABLE - NO POINT LOAD
W/ NEW FASCIA PLATE PF

FROM EXISTING FASCIA

76 x 38 x 1.2 76 x 38 x 1.6 76 x 38 x 2.0 90 x 38 x 1.2 90 x 38 x 1.6 75 x 50 x 1.6 75 x 50 x 2.0 100 x 50 x 1.6 150 x 50 x 3.0
TRUSSES OR CRANKED BEAM MAX PURLIN SPACING PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS
SPACING TO BE 4500 MAX
1200 4600 5100 5400 5300 5800 5300 5700 6700 9500
C
TYPICAL ELEVATION C
AT TRUSS (TR) - 1:100 END ELEVATION
1800 4100 4400 4700 4700 5100 4700 5000 5600 8800
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE.
FASCIA BEAM 2400 3700 4000 4300 4300 4600 4200 4500 5100 8200
MAXIMUM PURLIN 3m MAX BEAM SPAN FOR
EXISTING FASCIA & GUTTER OVERHANG AT GABLE END 600 (OR 20% OF THE BACKSPAN - WHICHEVER IS LESS) 900 (OR 20% OF THE BACKSPAN - WHICHEVER IS LESS)
(ADD FASCIA PLATE) FASCIA CONNECTION
GUTTER

1,000 1,000
1.8m MIN

TRUSS

INCL. IN TOTAL
RAFTER SPAN
PP PP PP PP PP PP PPPURLINS
PP MAX MAX
FULLY WELDED OUTRIGGERS REFER TO PURLIN MAX SPAN TABLE
TO REFER TO NOTES

3m MAX BEAM SPAN

END ELEVATION
PP FIX FASCIA PLATE GABLE TRUSS (GT) MAX SPAN TABLE
W/ SADDLE BRACKET
BEAM
BEAM

BEAM

BEAM

BEAM
TRUSS MEMBERS SPAN TO RHS SECTIONS REQUIRED
RAFTER BRACKET EACH SIDE BOUNDARY
OF FB FIXING POSITION LINE EXTENSION OF PURLIN 6000 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. 400 TOP
PP PC & PEB OR BOTTOM CHORD EXTENSIONS.
UNLESS FASCIA PLATE EXTENDED TO SETBACK OF 8000 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. NO
CORNER AND A RAFTER BRACKET STEEL COLUMNS LOCATION PC ON PEB OR TRUSS EXISTING EXTENSIONS.
INSTALLED AT THE EXISTING HIP RAFTER. (IF TRUSS EXTENDED TO BOUNDARY) HOUSE
76 x 38 x 1.6 PATIO TUBE
TYPICAL PLAN
PP OR
8000 (WITH FOR TOP / BOTTOM CHORD EXTENSIONS TO 1000mm,
NOTES: 1000 MAX FOR USE 100 x 50 x 2.0 RHS.
100 x 50 x 2.0 RHS DURAGAL
- PROVIDE COLUMNS AT EACH TRUSS FOR FREESTANDING ROOF. EXTENSIONS) OTHERWISE AS PER 8000 SPAN ABOVE.
PATIO COLUMN & GT/CB
- FULLY WELDED OUTRIGGERS TO TRUSS @ 1200 CRS MAX. TO REFER TO SECTION B. PF PF
PATIO FOOTING) LENGTH TO BE 6000 MAX 10000 TOP CHORD 76 x 38 x 1.6 RHS Gr350 - NO EXTENSIONS.
- ROOF PITCH TO BE FROM 12 TO 30° MAX. WEBS 76 x 38 x 1.6 RHS OR 30 x 1.6 SHS. BOTTOM
- WHERE NO WALL OR ROOF FIXING ON SIDE OF PATIO, REFER TO FREESTANDING DETAIL. CHORD 100 x 50 x 2.0 RHS. NO EXTENSIONS.
- OPTION: RAFTER BRACKETS TO BE FIXED TO EVERY 2ND EXISTING RAFTER (1200 CRS MAX). TRUSS

TYPICAL PLAN - 1:100 BEAM SPACING PATIO PURLIN END ELEVATION - OPTION POST EXTENSION/POST SETBACK
NOTES: CL (REFER TO TABLE) CL PATIO COLUMN (PC) PATIO CONDITIONS (TOPOGRAPHICAL FACTOR OF 1.0)
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN
BEAM SPACING TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS.
BEAM SPACING
- STEEL GR350 FOR CL
76 x(REFER
38 x 1.2
TO/ TABLE)
1.6 MEMBERS, & GR450
CL (REFER DURAGALCL
TO TABLE) FOR OTHERS U.N.O. 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT TERRAIN CATEGORY FULL PARTIAL NO
SHIELDING SHIELDING SHIELDING
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. TRUSS
76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE.
90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING
TERRAIN CATEGORY - 3
¸
GT/CB TERRAIN CATEGORY - 2.5
PURLINS CTRS TO 100 x 50 x 2.0 SHS PATIOS (OR LARGER COLUMN FOR
REFER TO TABLE

SUIT CLADDING 150 x 50 x 2.0 SHS AESTHETIC REASONS) TERRAIN CATEGORY - 2

EDGE PATIO B (REFER TO MAX SPAN 90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT BEAM - NO GYPROCK OR TIMBER CEILING
BEAM PURLIN
PURLIN TABLE) - NO SOLARSPAN OR ECLIPSE TYPE ROOF
PE & CRITERIA GT/CB 100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHTPURLIN - NO POINT LOADS
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO APATIO PATIO FOOTING
ULAR HOUSE. COLUMN (REFER TO TYPICAL 150SETBACK
x 50 x 3.0 OF
SHS (Gr450) WHEN ADDING SOLAR PANELS
SIGN LOADINGS ARE AS/NZS 1170. PC BASE FIXING PC ON BEAM
PATIO COLUMNS
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN DETAIL) 6000 MAX
FOR FREE-STANDING STRUCTURES THE
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS MAXIMUM COLUMN SPACING IN EACH
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED. GT/CB DIRECTION IS 6 METRES. PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS VOIDS THE PP - PATIO PURLIN
PEB - EDGE BEAM
TIFICATION.
FRONT ELEVATION FREESTANDING PLAN OPTION END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG, PC - PATIO COLUMN
PF - PATIO FOOTING
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 1:100
Scale: Sheet:
S1.1 Sheet:
S1.2
ionGSPublisherVersion
0.0.100.100 0.0.100.100
 CRANKED BEAMS (CB) MAX SPAN TABLE - 1kN MAX POINT LOAD PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS(PC) BASE FIXINGS
COLUMN

RAFTER / BEAM SKILLION

76 x 38 x 1.2 76 x 38 x 1.6 76 x 38 x 2.0 90 x 38 x 1.2 76xx3.0
38 x 1.2100
90 x 38 x 1.6
75 x 50 PATIO
x 50TUBE 100 x 50 xTO
75 x 50 x 1.6
x 1.6 2.03000 MAX
75 x 50 x 2.0100 xHEIGHT
50 x 3.0 ROOF150
150 x 50 x 2.0 AREA
x 50 x 3.0 FOOTING SIZE (PC CAST IN)
ROOF AREA SLAB
FOOTING SIZE THICKNESS
(PC CAST IN) (PC FIXING ON THICKNESS
SLAB TOP) (PC
SPACING ALTERNATIVE
PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE
DURAGAL76 xRHS DURAGAL RHS
DURAGAL
38 x 1.6 PATIO TUBE DURAGAL RHS
RHS DURAGALTO RHS3600DURAGAL
MAX HEIGHTRHS DURAGAL RHS DURAGAL RHS FIXING ON TOP)
8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN UNREINFORCED SLAB
1800 3400 PP
4700 B 4300 5100 PP 4700 3900 B 5600 5900 B
6300 5000 7100 8900 8700 8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN
90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m² 600 x 600 x 600 DEEP MASS CONCRETE 100mm MIN REINFORCED SLAB
UNREINFORCED SLAB
2400 3300 4000 4300 3700 4600 4200 4500 5100 100 x 50 x 2.05300
SHS 5700(OR LARGER 6400
PATIOS COLUMN FOR 8100 8100
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² DEEP MASS600
14m²
700 x 700 x 700 x 600 x 600 DEEP MASS CONCRETE
CONCRETE N/A 100mm MIN REINFORCED
3000 3000 3700 4000 3600 4300 3900 4200 4700 5000 5300 6000 7500 7700 SLAB
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 700 x 700 x 700 DEEP MASS700CONCRETE
x 700 x 700 DEEP MASS CONCRETE
3600 2900 3500 3800 3500 4000 3700 3900 4400 4700 5000 5600 7000 7300 20m² N/A
DOME TRUSS FREESTANDING OR N/A
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT
4200 ALTERNATIVE
2800 3300 PP PP
3600 PP 3400 PP 3800 PP PP
3500 3700 4200 4400 4700 5300 6700 7100 Ø300 x 1200 DEEP MASS 700 x
CONCRETE 700 x 900
PILE DEEP MASS CONCRETE
150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS FREESTANDING OR N/A
B B B
NOTE: FOR SOLARSPAN TYPE ROOF OR TIMBER/GYPROCK CEILINGS REDUCE THESE SPAN VALUES BY 20%. SOLARSPAN TO BE INSTALLED TO MANUFACTURER'S SPECIFICATIONS Ø300 x 1200 DEEP MASS CONCRETE PILE

RAFTER BRACKETS TO BE FIXED

TRUSS
TO EVERY 3RD EXISTING RAFTER A EDGE BEAMS (PEB) MAX SPAN TABLE - 1kN MAX POINT LOAD
(1800 CRS MAX) PP PP PP PP
GABLE TRUSS PP EXISTING RAFTERS PP 100 x 50 x 1.6 100 x 50 x 2.0 100 x 50 x 3.0 150 x 50 x 2.0 150 x 50 x 3.0 150 x 50 x 4.0 150 x 100 x 4.0 C20015 C20019 C25019
PP PP
DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS LYSAGHT G450 LYSAGHT G450 LYSAGHT G450
B B B B PATIO WIDTH MAX = 4000 5400 6100 6700 8400 9300 9700 10900 8100 9000 9600
PP EXISTING WALL
PATIO WIDTH MAX = 6000 4500 5200 6000 7000 8400 BEAM 8800 10000 7200 8100 8700
PATIO WIDTH MAX = 8000 3900 4500 5400 6100 7700 PURLIN 8200 9000 6600 7300 8100
PATIO WIDTH MAX = 10000 3500 4100 5000 5500 7000 7700 8600 6100 6800 7500
NOTE: FOR SOLARSPAN TYPE ROOF OR TIMBER/GYPROCK CEILINGS REDUCE THESE SPAN VALUES BY 20%. MAXIMUM CANTILEVER OF
EXISTING
PEB/GT/CB FROM OFFSET PC TO GABLE END TRUSS IS 15% OF THE BACKSPAN (MAX 1000)
3m MAX BEAM SPAN FOR HOUSE
PC PC PC PC
FASCIA
(PP)CONNECTION

TRUSS SPAN AS PER SPAN TABLE

PURLIN MAX SPAN TABLE - 1kN MAX POINT LOAD
PF PF PF PF

TRUSS SPAN AS PER SPAN TABLE

FROM EXISTING BRICKWORK

EXISTING FASCIA PLATE
W/ NEW FASCIA PLATE MAX PURLIN 76 x 38 x 1.2 76 x 38 x 1.6 76 x 38 x 2.0
PF 90 x 38 x 1.2 90 x 38 x 1.6 75 x 50 x 1.6 75 x 50 x 2.0 100 x 50 x 1.6 150 x 50 x 3.0

FROM EXISTING FASCIA

SPACING PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS
TRUSSES OR CRANKED BEAM 1200 3800 4500 4800 4500 5300 4800 5200 6600 9400
SPACING TO BE 4500 MAX
1800 3400 4300 4700 3900 5100 4700 5000 5600 8700
C
TYPICAL ELEVATION C
AT TRUSS (TR) - 1:100 END ELEVATION -25%
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE. 2400 3300 4000 4300 3700 4600 4200 4500 5100 8100
FASCIA BEAM
3000 3000 3700 4000 3600 4300 3900 4200 4700 7700
MAXIMUM PURLIN 3m MAX BEAM SPAN FOR 900 (OR 20% OF THE BACKSPAN - WHICHEVER IS LESS)
EXISTING FASCIA & GUTTER OVERHANG AT 600 (OR 20% OF THE BACKSPAN - WHICHEVER IS LESS)
(ADD FASCIA PLATE) GABLE END FASCIA CONNECTION
GUTTER
NOTE: FOR SOLARSPAN TYPE ROOF OR TIMBER/GYPROCK CEILINGS REDUCE TOTAL SPAN VALUE BY THESE PERCENTAGES (OR HALVE THE PURLIN SPACING)
1,000 1,000

EXTENDED SPAN
1.8m MIN

TRUSS

INCL. IN TOTAL
RAFTER SPAN
PP PP PP PP PP PP PPPURLINS
PP MAX MAX
FULLY WELDED OUTRIGGERS REFER TO PURLIN MAX SPAN TABLE
TO REFER TO NOTES

3m MAX BEAM SPAN

END ELEVATION
PP FIX FASCIA PLATE
W/ SADDLE BRACKET GABLE TRUSS (GT) MAX SPAN TABLE
BEAM
BEAM

BEAM

BEAM

BEAM
RAFTER BRACKET EACH SIDE BOUNDARY
OF FB FIXING POSITION LINE EXTENSION OF TRUSS MEMBERS
PURLIN SPAN TO RHS SECTIONS REQUIRED
PP PC & PEB 6000 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. 400 TOP
UNLESS FASCIA PLATE EXTENDED TO SETBACK OF OR BOTTOM CHORD EXTENSIONS.
CORNER AND A RAFTER BRACKET STEEL COLUMNS LOCATION PC ON PEB OR TRUSS EXISTING
INSTALLED AT THE EXISTING HIP RAFTER. (IF TRUSS EXTENDED TO BOUNDARY) 8000 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. NO
HOUSE
EXTENSIONS.
TYPICAL PLAN
PP
76 x 38 x 1.6 PATIO TUBE
NOTES: 8000 (WITH FOR TOP / BOTTOM CHORD EXTENSIONS TO 1000mm,
OR
- PROVIDE COLUMNS AT EACH TRUSS FOR FREESTANDING ROOF. GT/CB 1000 MAX FOR USE 100 x 50 x 2.0 RHS.
PATIO COLUMN & PF PF 100 x 50 x 2.0 RHS DURAGAL
- FULLY WELDED OUTRIGGERS TO TRUSS @ 1200 CRS MAX. TO REFER TO SECTION B. LENGTH TO BE 6000 MAX EXTENSIONS) OTHERWISE AS PER 8000 SPAN ABOVE.
- ROOF PITCH TO BE FROM 12 TO 30° MAX. PATIO FOOTING)
- WHERE NO WALL OR ROOF FIXING ON SIDE OF PATIO, REFER TO FREESTANDING DETAIL. 10000 TOP CHORD 76 x 38 x 1.6 RHS Gr350 - NO EXTENSIONS.
- OPTION: RAFTER BRACKETS TO BE FIXED TO EVERY 2ND EXISTING RAFTER (1200 CRS MAX). TRUSS WEBS 76 x 38 x 1.6 RHS OR 30 x 1.6 SHS. BOTTOM
CHORD 100 x 50 x 2.0 RHS. NO EXTENSIONS.
TYPICAL PLAN - 1:100 BEAM SPACING PATIO PURLIN END ELEVATION - OPTION POST EXTENSION/POST SETBACK
NOTES: CL (REFER TO TABLE) CL PATIO COLUMN (PC)
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN
BEAM SPACING TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS.
BEAM SPACING
- STEEL GR350 FOR CL
76 x(REFER
38 x 1.2
TO/ TABLE)
1.6 MEMBERS, & GR450
CL (REFER DURAGALCL
TO TABLE) FOR OTHERS U.N.O. 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT PATIO CONDITIONS (TOPOGRAPHICAL FACTOR OF 1.0)
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. TRUSS FULL PARTIAL NO
76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT TERRAIN CATEGORY
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE. SHIELDING SHIELDING SHIELDING
GT/CB
PURLINS CTRS TO
90 x 90 x 2.0 SHS (Gr450)
100 x 50 x 2.0 SHS
TO 4000 MAX HEIGHT & FREESTANDING
PATIOS (OR LARGER COLUMN FOR
TERRAIN CATEGORY - 3
¸ ¸
¸ ¸
REFER TO TABLE

150 x 50 x 2.0 SHS AESTHETIC REASONS) TERRAIN CATEGORY - 2.5

SUIT CLADDING
EDGE PATIO B
BEAM PURLIN
(REFER TO MAX SPAN
PURLIN TABLE)
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT BEAM TERRAIN CATEGORY - 2
¸
PE & CRITERIA GT/CB 100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHTPURLIN - 1kN MAX POINT LOAD
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO APATIO PATIO FOOTING
ULAR HOUSE. COLUMN (REFER TO TYPICAL 150SETBACK
x 50 x 3.0 OF
SHS (Gr450) WHEN ADDING SOLAR PANELS
SIGN LOADINGS ARE AS/NZS 1170. PC BASE FIXING PC ON BEAM
PATIO COLUMNS
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN DETAIL) 6000 MAX
FOR FREE-STANDING STRUCTURES THE
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS MAXIMUM COLUMN SPACING IN EACH
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED. GT/CB DIRECTION IS 6 METRES. PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS VOIDS THE PP - PATIO PURLIN
PEB - EDGE BEAM
TIFICATION.
FRONT ELEVATION FREESTANDING PLAN OPTION END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG, PC - PATIO COLUMN
PF - PATIO FOOTING
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 1:100
Scale: Sheet:
S1.1 Sheet:
S1.3
ionGSPublisherVersion
0.0.100.100 0.0.100.100
 CRANKED BEAMS (CB) MAX SPAN TABLE - NO POINT LOAD PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS(PC) BASE FIXINGS
COLUMN

RAFTER / BEAM SKILLION

76 x 38 x 1.2 76 x 38 x 1.6 76 x 38 x 2.0 90 x 38 x 1.2 90 x 38 x 1.6 75 x 50 x 1.6 75 x 50 x 2.0 76xx3.0
75 x 50 38 x 1.2100
PATIO
x 50TUBE
x 1.6 100 x 50 xTO
2.03000 MAX
100 xHEIGHT
50 x 3.0 ROOF150
150 x 50 x 2.0 AREA
x 50 x 3.0 FOOTING SIZE (PC CAST IN)
ROOF AREA SLAB
FOOTING SIZE THICKNESS
(PC CAST IN) (PC FIXING ON THICKNESS
SLAB TOP) (PC
SPACING ALTERNATIVE
PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE DURAGAL RHS DURAGAL RHS DURAGAL76 xRHS DURAGAL
38 x 1.6 PATIO TUBERHS DURAGALTO RHS3600DURAGAL
MAX HEIGHTRHS DURAGAL RHS DURAGAL RHS FIXING ON TOP)
8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN UNREINFORCED SLAB
1800 4100 B 4400 PP
4700 4700 B 5100 PP 4700 B 5000 5600 5900 6300 7100 8900 8700 8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN
90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m² 600 x 600 x 600 DEEP MASS CONCRETE 100mm MIN REINFORCED SLAB
UNREINFORCED SLAB
2400 3700 4000 4300 4300 4600 4200 4500 5100 100 x 50 x 2.05300
SHS 5700(OR LARGER 6400
PATIOS COLUMN FOR 8100 8100
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² DEEP MASS600
14m²
700 x 700 x 700 x 600 x 600 DEEP MASS CONCRETE
CONCRETE N/A 100mm MIN REINFORCED
3000 3400 3700 4000 4000 4300 3900 4200 4700 5000 5300 6000 7500 7700 SLAB
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 700 x 700 x 700 DEEP MASS700CONCRETE
x 700 x 700 DEEP MASS CONCRETE
3600 3200 3500 3800 3700 4000 3700 3900 4400 4700 5000 5600 7000 7300 20m² N/A
DOME TRUSS FREESTANDING OR N/A
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT
4200 ALTERNATIVE
3000 3300 PP PP
3600 PP 3500 PP 3800 PP PP
3500 3700 4200 4400 4700 5300 6700 7100 Ø300 x 1200 DEEP MASS 700 x
CONCRETE 700 x 900
PILE DEEP MASS CONCRETE
150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS FREESTANDING OR N/A
B B B
Ø300 x 1200 DEEP MASS CONCRETE PILE

RAFTER BRACKETS TO BE FIXED

TRUSS
TO EVERY 3RD EXISTING RAFTER A EDGE BEAMS (PEB) MAX SPAN TABLE - NO POINT LOAD
(1800 CRS MAX) PP PP PP PP
GABLE TRUSS PP EXISTING RAFTERS PP
PP PP 100 x 50 x 1.6 100 x 50 x 2.0 100 x 50 x 3.0 150 x 50 x 2.0 150 x 50 x 3.0 150 x 50 x 4.0 150 x 100 x 4.0 C20015 C20019 C25019
DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS LYSAGHT G450 LYSAGHT G450 LYSAGHT G450
B B B B
PATIO WIDTH MAX = 4000 5400 6100 6700 8400 9300 9700 10900 8100 9000 9600
PP EXISTING WALL
PATIO WIDTH MAX = 6000 4500 5200 6000 7000 8400 BEAM 8800 10000 7200 8100 8700
PATIO WIDTH MAX = 8000 3900 4500 5400 6100 7700 PURLIN 8200 9000 6600 7300 8100
PATIO WIDTH MAX = 10000 3500 4100 5000 5500 7000 7700 8600 6100 6800 7500
* NO BEAM CANTILEVER ALLOWED EXISTING
3m MAX BEAM SPAN FOR HOUSE
PC PC PC PC

TRUSS SPAN AS PER SPAN TABLE

FASCIA CONNECTION
PF PF PF PF

TRUSS SPAN AS PER SPAN TABLE

FROM EXISTING BRICKWORK

EXISTING FASCIA PLATE PURLIN (PP) MAX SPAN TABLE - NO POINT LOAD
W/ NEW FASCIA PLATE PF

FROM EXISTING FASCIA

76 x 38 x 1.2 76 x 38 x 1.6 76 x 38 x 2.0 90 x 38 x 1.2 90 x 38 x 1.6 75 x 50 x 1.6 75 x 50 x 2.0 100 x 50 x 1.6 150 x 50 x 3.0
TRUSSES OR CRANKED BEAM MAX PURLIN SPACING PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS
SPACING TO BE 4500 MAX
4600 5100 5400 5300 5800 5300 5700 6700 9400
C
TYPICAL ELEVATION C
AT TRUSS (TR) - 1:100 1200 END ELEVATION
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE. 1800 4100 4400 4700 4700 5100 4700 5000 5600 8700
FASCIA BEAM
2400 3700 4000 4300 4300 4600 4200 4500 5100 8100

EXISTING FASCIA & GUTTER MAXIMUM PURLIN 3m MAX BEAM SPAN FOR
600 (OR 20% OF THE BACKSPAN - WHICHEVER IS LESS) 900 (OR 20% OF THE BACKSPAN - WHICHEVER IS LESS)
(ADD FASCIA PLATE) OVERHANG AT GABLE END FASCIA CONNECTION
GUTTER

1,000 1,000

EXTENDED SPAN
1.8m MIN

TRUSS

INCL. IN TOTAL
RAFTER SPAN
PP PP PP PP PP PP PPPURLINS
PP MAX MAX
FULLY WELDED OUTRIGGERS REFER TO PURLIN MAX SPAN TABLE
TO REFER TO NOTES

3m MAX BEAM SPAN

END ELEVATION
PP FIX FASCIA PLATE GABLE TRUSS (GT) MAX SPAN TABLE
W/ SADDLE BRACKET
BEAM
BEAM

BEAM

BEAM

BEAM
TRUSS MEMBERS SPAN TO RHS SECTIONS REQUIRED
RAFTER BRACKET EACH SIDE BOUNDARY
OF FB FIXING POSITION LINE EXTENSION OF PURLIN 6000 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. 400 TOP
PP PC & PEB OR BOTTOM CHORD EXTENSIONS.
UNLESS FASCIA PLATE EXTENDED TO SETBACK OF 8000 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. NO
CORNER AND A RAFTER BRACKET STEEL COLUMNS LOCATION PC ON PEB OR TRUSS EXISTING EXTENSIONS.
INSTALLED AT THE EXISTING HIP RAFTER. (IF TRUSS EXTENDED TO BOUNDARY) HOUSE
76 x 38 x 1.6 PATIO TUBE
TYPICAL PLAN
PP OR
8000 (WITH FOR TOP / BOTTOM CHORD EXTENSIONS TO 1000mm,
NOTES: 1000 MAX FOR USE 100 x 50 x 2.0 RHS.
100 x 50 x 2.0 RHS DURAGAL
- PROVIDE COLUMNS AT EACH TRUSS FOR FREESTANDING ROOF. EXTENSIONS) OTHERWISE AS PER 8000 SPAN ABOVE.
PATIO COLUMN & GT/CB
- FULLY WELDED OUTRIGGERS TO TRUSS @ 1200 CRS MAX. TO REFER TO SECTION B. PF PF
PATIO FOOTING) LENGTH TO BE 6000 MAX 10000 TOP CHORD 76 x 38 x 1.6 RHS Gr350 - NO EXTENSIONS.
- ROOF PITCH TO BE FROM 12 TO 30° MAX. WEBS 76 x 38 x 1.6 RHS OR 30 x 1.6 SHS. BOTTOM
- WHERE NO WALL OR ROOF FIXING ON SIDE OF PATIO, REFER TO FREESTANDING DETAIL. CHORD 100 x 50 x 2.0 RHS. NO EXTENSIONS.
- OPTION: RAFTER BRACKETS TO BE FIXED TO EVERY 2ND EXISTING RAFTER (1200 CRS MAX). TRUSS

TYPICAL PLAN - 1:100 BEAM SPACING PATIO PURLIN END ELEVATION - OPTION POST EXTENSION/POST SETBACK
NOTES: CL (REFER TO TABLE) CL PATIO COLUMN (PC)
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN
BEAM SPACING TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS.
BEAM SPACING
- STEEL GR350 FOR CL
76 x(REFER
38 x 1.2
TO/ TABLE)
1.6 MEMBERS, & GR450
CL (REFER DURAGALCL
TO TABLE) FOR OTHERS U.N.O. 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT PATIO CONDITIONS (TOPOGRAPHICAL FACTOR OF 1.0)
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. TRUSS FULL PARTIAL NO
76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT TERRAIN CATEGORY
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE. SHIELDING SHIELDING SHIELDING

GT/CB
PURLINS CTRS TO
90 x 90 x 2.0 SHS (Gr450)
100 x 50 x 2.0 SHS
TO 4000 MAX HEIGHT & FREESTANDING
PATIOS (OR LARGER COLUMN FOR
TERRAIN CATEGORY - 3
¸ ¸
¸ ¸
REFER TO TABLE

150 x 50 x 2.0 SHS TERRAIN CATEGORY - 2.5

SUIT CLADDING AESTHETIC REASONS)
EDGE PATIO B
BEAM PURLIN
(REFER TO MAX SPAN
PURLIN TABLE)
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT BEAM TERRAIN CATEGORY - 2
¸
PE & CRITERIA GT/CB 100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHTPURLIN - NO GYPROCK OR TIMBER CEILING
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO APATIO PATIO FOOTING - NO SOLARSPAN OR ECLIPSE TYPE ROOF
ULAR HOUSE. COLUMN (REFER TO TYPICAL SETBACK
150 x 50 x 3.0OF
SHS (Gr450) WHEN ADDING SOLAR PANELS - NO POINT LOADS
SIGN LOADINGS ARE AS/NZS 1170. PC BASE FIXING PC ON BEAM
PATIO COLUMNS
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN DETAIL) 6000 MAX
FOR FREE-STANDING STRUCTURES THE
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS MAXIMUM COLUMN SPACING IN EACH
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED. GT/CB DIRECTION IS 6 METRES. PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS VOIDS THE PP - PATIO PURLIN
PEB - EDGE BEAM
TIFICATION.
FRONT ELEVATION FREESTANDING PLAN OPTION END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG, PC - PATIO COLUMN
PF - PATIO FOOTING
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 1:100
Scale: Sheet:
S1.1 Sheet:
S1.4
ionGSPublisherVersion
0.0.100.100 0.0.100.100
 CRANKED BEAMS (CB) MAX SPAN TABLE - 1kN MAX POINT LOAD PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS(PC) BASE FIXINGS
COLUMN

RAFTER / BEAM SKILLION

76 x 38 x 1.2 76 x 38 x 1.6 76 x 38 x 2.0 90 x 38 x 1.2 76xx3.0
38 x 1.2100
90 x 38 x 1.6
75 x 50 PATIO
x 50TUBE 100 x 50 xTO
75 x 50 x 1.6
x 1.6 2.03000 MAX
75 x 50 x 2.0100 xHEIGHT
50 x 3.0 ROOF150
150 x 50 x 2.0 AREA
x 50 x 3.0 FOOTING SIZE (PC CAST IN)
ROOF AREA SLAB
FOOTING SIZE THICKNESS
(PC CAST IN) (PC FIXING ON THICKNESS
SLAB TOP) (PC
SPACING ALTERNATIVE
PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE
DURAGAL76 xRHS DURAGAL RHS
DURAGAL
38 x 1.6 PATIO TUBE DURAGAL RHS
RHS DURAGALTO RHS3600DURAGAL
MAX HEIGHTRHS DURAGAL RHS DURAGAL RHS FIXING ON TOP)
8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN UNREINFORCED SLAB
1800 3400 PP
4700 B 4300 5100 PP 4700 3900 B 5600 5900 B
6300 5000 7100 8900 8700 8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN
90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m² 600 x 600 x 600 DEEP MASS CONCRETE 100mm MIN REINFORCED SLAB
UNREINFORCED SLAB
2400 3300 4000 4300 3700 4600 4200 4500 5100 100 x 50 x 2.05300
SHS 5700(OR LARGER 6400
PATIOS COLUMN FOR 8100 8100
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² DEEP MASS600
14m²
700 x 700 x 700 x 600 x 600 DEEP MASS CONCRETE
CONCRETE N/A 100mm MIN REINFORCED
3000 3000 3700 4000 3600 4300 3900 4200 4700 5000 5300 6000 7500 7700 SLAB
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 700 x 700 x 700 DEEP MASS700CONCRETE
x 700 x 700 DEEP MASS CONCRETE
3600 2900 3500 3800 3500 4000 3700 3900 4400 4700 5000 5600 7000 7300 20m² N/A
DOME TRUSS FREESTANDING OR N/A
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT
4200 ALTERNATIVE
2800 3300 PP PP
3600 PP 3400 PP 3800 PP PP
3500 3700 4200 4400 4700 5300 6700 7000 Ø300 x 1200 DEEP MASS 700 x
CONCRETE 700 x 900
PILE DEEP MASS CONCRETE
150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS FREESTANDING OR N/A
B B B
NOTE: FOR SOLARSPAN TYPE ROOF OR TIMBER/GYPROCK CEILINGS REDUCE THESE SPAN VALUES BY 20%. SOLARSPAN TO BE INSTALLED TO MANUFACTURER'S SPECIFICATIONS Ø300 x 1200 DEEP MASS CONCRETE PILE

RAFTER BRACKETS TO BE FIXED

TRUSS
TO EVERY 3RD EXISTING RAFTER A EDGE BEAMS (PEB) MAX SPAN TABLE - 1kN MAX POINT LOAD
(1800 CRS MAX) PP PP PP PP
GABLE TRUSS PP EXISTING RAFTERS PP 100 x 50 x 1.6 100 x 50 x 2.0 100 x 50 x 3.0 150 x 50 x 2.0 150 x 50 x 3.0 150 x 50 x 4.0 150 x 100 x 4.0 C20015 C20019 C25019
PP PP
DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS LYSAGHT G450 LYSAGHT G450 LYSAGHT G450
B B B B PATIO WIDTH MAX = 4000 5400 6100 6700 8400 9300 9700 10900 8100 9000 9600
PP EXISTING WALL
PATIO WIDTH MAX = 6000 4500 5200 6000 7000 8400 BEAM 8800 10000 7200 8100 8700
PATIO WIDTH MAX = 8000 3900 4500 5400 6100 7700 PURLIN 8200 9000 6600 7300 8100
PATIO WIDTH MAX = 10000 3500 4100 5000 5500 7000 7700 8600 6100 6800 7500
NOTE: FOR SOLARSPAN TYPE ROOF OR TIMBER/GYPROCK CEILINGS REDUCE THESE SPAN VALUES BY 20%. MAXIMUM CANTILEVER OF
EXISTING
PEB/GT/CB FROM OFFSET PC TO GABLE END TRUSS IS 15% OF THE BACKSPAN (MAX 1000)
3m MAX BEAM SPAN FOR HOUSE
PC PC PC PC
FASCIA CONNECTION

TRUSS SPAN AS PER SPAN TABLE

PF PF PF PF

TRUSS SPAN AS PER SPAN TABLE

FROM EXISTING BRICKWORK

PURLIN (PP) MAX SPAN TABLE - 1kN MAX POINT LOAD
EXISTING FASCIA PLATE
W/ NEW FASCIA PLATE PF

FROM EXISTING FASCIA

MAX PURLIN 76 x 38 x 1.2 76 x 38 x 1.6 76 x 38 x 2.0 90 x 38 x 1.2 90 x 38 x 1.6 75 x 50 x 1.6 75 x 50 x 2.0 100 x 50 x 1.6 150 x 50 x 3.0
TRUSSES OR CRANKED BEAM SPACING PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS
SPACING TO BE 4500 MAX 1200 3800 4500 4800 4500 5300 4800 5200 6600 9400
C
TYPICAL ELEVATION C
AT TRUSS (TR) - 1:100 1800 3400 END
4300 ELEVATION
4700 3900 5100 4700 5000 5600 8700
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE. -25%
FASCIA BEAM 2400 3300 4000 4300 3700 4600 4200 4500 5100 8100
3000 3000 3700 4000 3600 4300 3900 4200 4700 7700
EXISTING FASCIA & GUTTER 3m MAX BEAM SPAN FOR
MAXIMUM PURLIN
(ADD FASCIA PLATE) FASCIA CONNECTION
600 (OR 20% OF THE BACKSPAN - WHICHEVER IS LESS) 900 (OR 20% OF THE BACKSPAN - WHICHEVER IS LESS)
GUTTER OVERHANG AT
GABLE END
NOTE: FOR SOLARSPAN TYPE ROOF OR TIMBER/GYPROCK
1,000 CEILINGS
1,000 REDUCE TOTAL SPAN VALUE BY THESE PERCENTAGES (OR HALVE THE PURLIN SPACING)

EXTENDED SPAN
1.8m MIN

TRUSS

INCL. IN TOTAL
RAFTER SPAN
PP PP PP PP PP PP PPPURLINS
PP MAX MAX
FULLY WELDED OUTRIGGERS REFER TO PURLIN MAX SPAN TABLE
TO REFER TO NOTES

3m MAX BEAM SPAN

END ELEVATION
PP FIX FASCIA PLATE
W/ SADDLE BRACKET GABLE TRUSS (GT) MAX SPAN TABLE
BEAM
BEAM

BEAM

BEAM

BEAM
RAFTER BRACKET EACH SIDE BOUNDARY
OF FB FIXING POSITION LINE EXTENSION OF TRUSS MEMBERS
PURLIN SPAN TO RHS SECTIONS REQUIRED
PP PC & PEB 6000 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. 400 TOP
UNLESS FASCIA PLATE EXTENDED TO SETBACK OF OR BOTTOM CHORD EXTENSIONS.
CORNER AND A RAFTER BRACKET STEEL COLUMNS LOCATION PC ON PEB OR TRUSS EXISTING
INSTALLED AT THE EXISTING HIP RAFTER. (IF TRUSS EXTENDED TO BOUNDARY) 8000 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. NO
HOUSE
EXTENSIONS.
TYPICAL PLAN
PP
76 x 38 x 1.6 PATIO TUBE
NOTES: 8000 (WITH FOR TOP / BOTTOM CHORD EXTENSIONS TO 1000mm,
OR
- PROVIDE COLUMNS AT EACH TRUSS FOR FREESTANDING ROOF. GT/CB 1000 MAX FOR USE 100 x 50 x 2.0 RHS.
PATIO COLUMN & PF PF 100 x 50 x 2.0 RHS DURAGAL
- FULLY WELDED OUTRIGGERS TO TRUSS @ 1200 CRS MAX. TO REFER TO SECTION B. LENGTH TO BE 6000 MAX EXTENSIONS) OTHERWISE AS PER 8000 SPAN ABOVE.
- ROOF PITCH TO BE FROM 12 TO 30° MAX. PATIO FOOTING)
- WHERE NO WALL OR ROOF FIXING ON SIDE OF PATIO, REFER TO FREESTANDING DETAIL. 10000 TOP CHORD 76 x 38 x 1.6 RHS Gr350 - NO EXTENSIONS.
- OPTION: RAFTER BRACKETS TO BE FIXED TO EVERY 2ND EXISTING RAFTER (1200 CRS MAX). TRUSS WEBS 76 x 38 x 1.6 RHS OR 30 x 1.6 SHS. BOTTOM
CHORD 100 x 50 x 2.0 RHS. NO EXTENSIONS.
TYPICAL PLAN - 1:100 BEAM SPACING PATIO PURLIN END ELEVATION - OPTION POST EXTENSION/POST SETBACK
NOTES: CL (REFER TO TABLE) CL PATIO COLUMN (PC)
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN
BEAM SPACING TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS.
BEAM SPACING
- STEEL GR350 FOR CL
76 x(REFER
38 x 1.2
TO/ TABLE)
1.6 MEMBERS, & GR450
CL (REFER DURAGALCL
TO TABLE) FOR OTHERS U.N.O. 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT PATIO CONDITIONS (TOPOGRAPHICAL FACTOR OF 1.0)
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. TRUSS FULL PARTIAL NO
76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT TERRAIN CATEGORY
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE. SHIELDING SHIELDING SHIELDING
GT/CB 90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING TERRAIN CATEGORY - 3
PURLINS CTRS TO 100 x 50 x 2.0 SHS PATIOS (OR LARGER COLUMN FOR
¸
REFER TO TABLE

150 x 50 x 2.0 SHS AESTHETIC REASONS) TERRAIN CATEGORY - 2.5

SUIT CLADDING
EDGE PATIO B
BEAM PURLIN
(REFER TO MAX SPAN
PURLIN TABLE)
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT BEAM TERRAIN CATEGORY - 2
¸ ¸
PE & CRITERIA GT/CB 100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHTPURLIN - 1kN MAX POINT LOAD
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO APATIO PATIO FOOTING
ULAR HOUSE. COLUMN (REFER TO TYPICAL 150SETBACK
x 50 x 3.0 OF
SHS (Gr450) WHEN ADDING SOLAR PANELS
SIGN LOADINGS ARE AS/NZS 1170. PC BASE FIXING PC ON BEAM
PATIO COLUMNS
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN DETAIL) 6000 MAX
FOR FREE-STANDING STRUCTURES THE
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS MAXIMUM COLUMN SPACING IN EACH
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED. GT/CB DIRECTION IS 6 METRES. PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS VOIDS THE PP - PATIO PURLIN
PEB - EDGE BEAM
TIFICATION.
FRONT ELEVATION FREESTANDING PLAN OPTION END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG, PC - PATIO COLUMN
PF - PATIO FOOTING
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 1:100
Scale: Sheet:
S1.1 Sheet:
S1.5
ionGSPublisherVersion
0.0.100.100 0.0.100.100
 CRANKED BEAMS (CB) MAX SPAN TABLE - NO POINT LOAD PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS(PC) BASE FIXINGS
COLUMN

RAFTER / BEAM SKILLION

76 x 38 x 1.2 76 x 38 x 1.6 76 x 38 x 2.0 90 x 38 x 1.2 90 x 38 x 1.6 75 x 50 x 1.6 75 x 50 x 2.0 76xx3.0
75 x 50 38 x 1.2100
PATIO
x 50TUBE
x 1.6 100 x 50 xTO
2.03000 MAX
100 xHEIGHT
50 x 3.0 ROOF150
150 x 50 x 2.0 AREA
x 50 x 3.0 FOOTING SIZE (PC CAST IN)
ROOF AREA SLAB
FOOTING SIZE THICKNESS
(PC CAST IN) (PC FIXING ON THICKNESS
SLAB TOP) (PC
SPACING ALTERNATIVE
PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE DURAGAL RHS DURAGAL RHS DURAGAL76 xRHS DURAGAL
38 x 1.6 PATIO TUBERHS DURAGALTO RHS3600DURAGAL
MAX HEIGHTRHS DURAGAL RHS DURAGAL RHS FIXING ON TOP)
8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN UNREINFORCED SLAB
1800 4100 B 4400 PP
4700 4700 B 5100 PP 4700 B 5000 5600 5900 6300 7100 8900 8700 8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN
90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m² 600 x 600 x 600 DEEP MASS CONCRETE 100mm MIN REINFORCED SLAB
UNREINFORCED SLAB
2400 3700 4000 4300 4300 4600 4200 4500 5100 100 x 50 x 2.05300
SHS 5700(OR LARGER 6400
PATIOS COLUMN FOR 8100 8100
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² DEEP MASS600
14m²
700 x 700 x 700 x 600 x 600 DEEP MASS CONCRETE
CONCRETE N/A 100mm MIN REINFORCED
3000 3400 3700 4000 4000 4300 3900 4200 4700 5000 5300 6000 7500 7700 SLAB
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 700 x 700 x 700 DEEP MASS700CONCRETE
x 700 x 700 DEEP MASS CONCRETE
3600 3200 3500 3800 3700 4000 3700 3900 4400 4700 5000 5600 7000 7300 20m² N/A
DOME TRUSS FREESTANDING OR N/A
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT
4200 ALTERNATIVE
3000 3300 PP PP
3600 PP 3500 PP 3800 PP PP
3500 3700 4200 4400 4700 5300 6700 7000 Ø300 x 1200 DEEP MASS 700 x
CONCRETE 700 x 900
PILE DEEP MASS CONCRETE
150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS FREESTANDING OR N/A
B B B
Ø300 x 1200 DEEP MASS CONCRETE PILE

RAFTER BRACKETS TO BE FIXED

TRUSS
TO EVERY 3RD EXISTING RAFTER A
(1800 CRS MAX) PP PP PP PP EDGE BEAMS (PEB) MAX SPAN TABLE - NO POINT LOAD
GABLE TRUSS PP EXISTING RAFTERS PP
PP PP 100 x 50 x 1.6 100 x 50 x 2.0 100 x 50 x 3.0 150 x 50 x 2.0 150 x 50 x 3.0 150 x 50 x 4.0 150 x 100 x 4.0 C20015 C20019 C25019
DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS LYSAGHT G450 LYSAGHT G450 LYSAGHT G450
B B B B
EXISTING WALL PATIO WIDTH MAX = 4000 5400 6100 6700 8400 9300 9700 10900 8100 9000 9600
PP
BEAM
PATIO WIDTH MAX = 6000 4500 5200 6000 7000 8400 8800 10000 7200 8100 8700
PATIO WIDTH MAX = 8000 3900 4500 5400 6100 7700 PURLIN 8200
9000 6600 7300 8100
PATIO WIDTH MAX = 10000 3500 4100 5000 5500 7000 7700 8600 6100 6800 7500
* NO BEAM CANTILEVER ALLOWED EXISTING
3m MAX BEAM SPAN FOR HOUSE
PC PC PC PC

TRUSS SPAN AS PER SPAN TABLE

FASCIA CONNECTION
PF PF PF PF

TRUSS SPAN AS PER SPAN TABLE

FROM EXISTING BRICKWORK

EXISTING FASCIA PLATE PURLIN (PP) MAX SPAN TABLE - NO POINT LOAD
W/ NEW FASCIA PLATE PF

FROM EXISTING FASCIA

76 x 38 x 1.2 76 x 38 x 1.6 76 x 38 x 2.0 90 x 38 x 1.2 90 x 38 x 1.6 75 x 50 x 1.6 75 x 50 x 2.0 100 x 50 x 1.6 150 x 50 x 3.0
TRUSSES OR CRANKED BEAM MAX PURLIN SPACING PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS
SPACING TO BE 4500 MAX
1200 4600 5100 5400 5300 5800 5300 5700 6700 9400
C
TYPICAL ELEVATION C
AT TRUSS (TR) - 1:100 END ELEVATION
1800 4100 4400 4700 4700 5100 4700 5000 5900 8700
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE.
FASCIA BEAM 2400 3700 4000 4300 4300 4600 4200 4500 5300 8100

EXISTING FASCIA & GUTTER MAXIMUM PURLIN 3m MAX BEAM SPAN FOR
OVERHANG AT GABLE END 600 (OR 20% OF THE BACKSPAN - WHICHEVER IS LESS) 900 (OR 20% OF THE BACKSPAN - WHICHEVER IS LESS)
(ADD FASCIA PLATE) FASCIA CONNECTION
GUTTER

1,000 1,000

EXTENDED SPAN
1.8m MIN

TRUSS

INCL. IN TOTAL
RAFTER SPAN
PP PP PP PP PP PP PPPURLINS
PP MAX MAX
FULLY WELDED OUTRIGGERS REFER TO PURLIN MAX SPAN TABLE
TO REFER TO NOTES

3m MAX BEAM SPAN

END ELEVATION
PP FIX FASCIA PLATE GABLE TRUSS (GT) MAX SPAN TABLE
W/ SADDLE BRACKET
BEAM
BEAM

BEAM

BEAM

BEAM
TRUSS MEMBERS SPAN TO RHS SECTIONS REQUIRED
RAFTER BRACKET EACH SIDE BOUNDARY
OF FB FIXING POSITION LINE EXTENSION OF PURLIN 6000 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. 400 TOP
PP PC & PEB OR BOTTOM CHORD EXTENSIONS.
UNLESS FASCIA PLATE EXTENDED TO SETBACK OF 8000 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. NO
CORNER AND A RAFTER BRACKET STEEL COLUMNS LOCATION PC ON PEB OR TRUSS EXISTING EXTENSIONS.
INSTALLED AT THE EXISTING HIP RAFTER. (IF TRUSS EXTENDED TO BOUNDARY) HOUSE
76 x 38 x 1.6 PATIO TUBE
TYPICAL PLAN
PP OR
8000 (WITH FOR TOP / BOTTOM CHORD EXTENSIONS TO 1000mm,
NOTES: 1000 MAX FOR USE 100 x 50 x 2.0 RHS.
100 x 50 x 2.0 RHS DURAGAL
- PROVIDE COLUMNS AT EACH TRUSS FOR FREESTANDING ROOF. EXTENSIONS) OTHERWISE AS PER 8000 SPAN ABOVE.
PATIO COLUMN & GT/CB
- FULLY WELDED OUTRIGGERS TO TRUSS @ 1200 CRS MAX. TO REFER TO SECTION B. PF PF
PATIO FOOTING) LENGTH TO BE 6000 MAX 10000 TOP CHORD 76 x 38 x 1.6 RHS Gr350 - NO EXTENSIONS.
- ROOF PITCH TO BE FROM 12 TO 30° MAX. WEBS 76 x 38 x 1.6 RHS OR 30 x 1.6 SHS. BOTTOM
- WHERE NO WALL OR ROOF FIXING ON SIDE OF PATIO, REFER TO FREESTANDING DETAIL. CHORD 100 x 50 x 2.0 RHS. NO EXTENSIONS.
- OPTION: RAFTER BRACKETS TO BE FIXED TO EVERY 2ND EXISTING RAFTER (1200 CRS MAX). TRUSS

TYPICAL PLAN - 1:100 BEAM SPACING PATIO PURLIN END ELEVATION - OPTION POST EXTENSION/POST SETBACK
NOTES: CL (REFER TO TABLE) CL PATIO COLUMN (PC)
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN
BEAM SPACING TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS.
BEAM SPACING
- STEEL GR350 FOR CL
76 x(REFER
38 x 1.2
TO/ TABLE)
1.6 MEMBERS, & GR450
CL (REFER DURAGALCL
TO TABLE) FOR OTHERS U.N.O. 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT PATIO CONDITIONS (TOPOGRAPHICAL FACTOR OF 1.0)
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. TRUSS FULL PARTIAL NO
76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT TERRAIN CATEGORY
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE. SHIELDING SHIELDING SHIELDING

GT/CB 90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING TERRAIN CATEGORY - 3
PURLINS CTRS TO 100 x 50 x 2.0 SHS PATIOS (OR LARGER COLUMN FOR
¸
REFER TO TABLE

150 x 50 x 2.0 SHS TERRAIN CATEGORY - 2.5

SUIT CLADDING AESTHETIC REASONS)
EDGE PATIO B
BEAM PURLIN
(REFER TO MAX SPAN
PURLIN TABLE)
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT BEAM TERRAIN CATEGORY - 2
¸ ¸
PE & CRITERIA GT/CB 100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHTPURLIN - NO GYPROCK OR TIMBER CEILING
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO APATIO PATIO FOOTING - NO SOLARSPAN OR ECLIPSE TYPE ROOF
ULAR HOUSE. COLUMN (REFER TO TYPICAL 150SETBACK
x 50 x 3.0OF
SHS (Gr450) WHEN ADDING SOLAR PANELS - NO POINT LOADS
SIGN LOADINGS ARE AS/NZS 1170. PC BASE FIXING PC ON BEAM
PATIO COLUMNS
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN DETAIL) 6000 MAX
FOR FREE-STANDING STRUCTURES THE
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS MAXIMUM COLUMN SPACING IN EACH
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED. GT/CB DIRECTION IS 6 METRES. PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS VOIDS THE PP - PATIO PURLIN
PEB - EDGE BEAM
TIFICATION.
FRONT ELEVATION FREESTANDING PLAN OPTION END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG, PC - PATIO COLUMN
PF - PATIO FOOTING
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 1:100
Scale: Sheet:
S1.1 Sheet:
S1.6
ionGSPublisherVersion
0.0.100.100 0.0.100.100
 PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS

SKILLION1120 MAX 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT ROOF AREA FOOTING SIZE (PC CAST IN) SLAB THICKNESS (PC FIXING ON TOP)
ALTERNATIVE
GT CHORD GABLE TRUSS RAFTER BRACKETS TO BE FIXED
76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT 8m² 500 x 500 x 500 DEEP MASS CONCRETE D 75mm MIN UNREINFORCED SLAB
EXTENSIONB B B TO EVERY 2ND EXISTING RAFTER
BOUNDARY EXTENSION PP PURLIN PP GABLE TRUSS 90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING (1200 CRS MAX)
14m² 600 x 600 x 600 DEEP MASS CONCRETE 100mm MIN REINFORCED SLAB
OF GT & PEB 100 x 50 x 2.0 SHS PATIOS (OR LARGER COLUMN FOR EXISTING RAFTERS
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² 700 x 700 x 700 DEEP MASS CONCRETE N/A
FIXING TO BRICKWORK EDGE BEAM
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 700 x 700 x 700 DEEP MASS CONCRETE
OR EXISTING WALL
DOME TRUSS EDGE BEAM PURLINS 100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT FREESTANDING N/A
ALTERNATIVE PP PP PP PP FASCIA PP
FIXING TO PP Ø300 x 1200 DEEP MASS CONCRETE PILE

BOUNDARY LINE
B PATIO COLUMN B PATIOBCOLUMNS 150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS

PATIO FOOTING TRUSS EXISTING FASCIA PLATE

W/ NEW FASCIA PLATE
OFFSET FOOTING PP PP PP PP
GABLE
(REFER TO TYPICAL PC TRUSS PP PP PP PP
BASE FIXING DETAIL)
B B B B
PP
SECTION B THROUGH GABLE TRUSS (GT)

EDGE BEAM
BEAM

OR TRUSS
SECTION A THROUGH GABLE TRUSS (GT) - 1:100 1:100
NOTES: FOR FREESTANDING STRUCTURE PURLIN
- PATIO FIXED TO EXISTING HOUSE.
- SETBACK OF PC ON PEB CAN BE AT FRONT, REAR OR SIDE.
STEEL COLUMN
EXISTING SETBACK
1120 MAX 3m MAX BEAM SPAN FOR HOUSE
PC PC CRANKED BEAM PC PC
GT CHORD FASCIA CONNECTION

1,000
MAX
PF EXTENSION PF PURLIN PF PF
BOUNDARY EXTENSION CRANKED BEAM
FASCIA BEAM
OF GT & PEB PF

FIXING TO BRICKWORK 1000

EDGE BEAM MAX

TYPICAL ELEVATION AT TRUSS EDGE

(TR)BEAM
- 1:100 FIXING TO FASCIA
PURLINS END ELEVATION
BOUNDARY LINE

NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUITCOLUMN

PATIO PARTICULAR SITE. PATIO COLUMNS

PLAN - OPTION WITH POST SETBACK

EXISTING FASCIA & GUTTER PATIO FOOTING NOTE: 3m MAX BEAM SPAN FOR
(ADD FASCIA PLATE) FASCIA
- PATIO ROOF CONNECTION
ATTACHED TO RESIDENCE AS PATIO STANDARD DETAILS.
OFFSET FOOTING - SETBACK OF PC ON PEB OR TRUSS CAN BE AT FRONT, REAR OR SIDE ON PEB OR GT.
(REFER TO TYPICAL PC
BASE FIXING DETAIL) 1,000 1,000 1000 1000
PP PP PP PP PP PP PP PP TRUSS
MAX MAX MAX MAX
SECTION B THROUGH CRANKED BEAM (CB) GT OR CB

3m MAX BEAM SPAN

SECTION APPTHROUGH CRANKED BEAM (CB) - 1:100 1:100

END ELEVATION
PEB
NOTES: FOR FREESTANDING STRUCTURE
- PATIO FIXED TO EXISTING HOUSE. BEAM
BEAM

BEAM

BEAM

BEAM
- SETBACK OF PC ON PEB CAN BE AT FRONT, REAR OR SIDE. SETBACK OF
PC & PEB OR PURLIN
EXTENSION OF TRUSS
PP PC & PEB
SETBACK OF
PC ON PEB OR TRUSS PC PC EXISTINGPC PC
HOUSE
NEW BOX GUTTERPP EXISTING ROOF PF PF PF PF
RAFTER

TRUSS TOP CHORD PATIO COLUMN & PF PF

PATIO FOOTING)
SECTION B, POST SETBACK - 1:100 SECTION B, OPTION WHEN FIXED TO
TRUSS FOR FREESTANDING STRUCTURE
TRUSS JOINTS CRANKED BEAM - 1:100
TYPICAL
FULLYPLAN
WELDED - 1:100 END ELEVATION - OPTION POST EXTENSION/POST SETBACK
FOR FREESTANDING STRUCTURE
NOTES: 1000 1000
MAX MAX
- BASES, CONNECTION
TRUSS BOTTOM DETAILS & DETAILS NOT SHOWN TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS.
- STEEL GR350
CHORDFOR 76 x 38 x 1.2 / 1.6 MEMBERS, & GR450 DURAGAL FOR OTHERS U.N.O. GT OR CB
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. FIXING TO FIXING TO TRUSS
PEB
- OPTION RAFTER BRACKET AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE.
WITH EXTENSION BRICKWORK BRICKWORK
REFER TO NOTE
FIXING TO FIXING TO
FASCIA SETBACK OF FASCIA
PC ON PEB OR
TRUSS BEAM
PE & CRITERIA PURLIN
SECTION C - 1:20
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO A PC
SETBACK OF
PC
ULAR HOUSE. NOTE: RAFTER BRACKET TO BE 50 x 6.0mm x 600mm LONG AND FIXED TO
SIGN LOADINGS ARE AS/NZS 1170. PF PC ON BEAM PF
EXISTING TIMBER HOUSE RAFTERS WITH 4 x TYPE 17 14 x 50 TEK SCREWS.
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED.
PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS VOIDS THE
TIFICATION. SECTION D, POST SETBACK - 1:100 SECTION D,-OPTION
END ELEVATION OPTIONWHEN FIXED TO AND FIXED ON BEAM
POST SETBACK
PP - PATIO
PF - PATIO
PC
PURLIN
PEB - EDGE BEAM
FOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG,
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS
NOTE: PATIO FIXED TO EXISTING HOUSE.
CRANKED BEAM - 1:100 PC - PATIO COLUMN
PF - PATIO FOOTING
NOTE: PATIO FIXED TO EXISTING HOUSE. TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 1:100
Scale: Sheet:
S1.1 Sheet:
S2.1
ionGSPublisherVersion
0.0.100.100 0.0.100.100
 PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS

SKILLION 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT ROOF AREA FOOTING SIZE (PC CAST IN) SLAB THICKNESS (PC FIXING ON TOP)
ALTERNATIVE COLUMN BITUMEN PAINT ON
76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT 8m² 500 x 500 x 500 DEEP MASS
STEELCONCRETE
COLUMN 75mm MIN UNREINFORCED SLAB
B PP B PP B
90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m² 600 x 600 x 600 DEEP MASS CONCRETE 100mm MIN REINFORCED SLAB
100 x 50 x 2.0 SHS PATIOS (OR LARGER COLUMN FOR
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² 700 x 700 x 700 DEEP MASS CONCRETE N/A
INTERNAL U CLEAT 700 x 700 x 700 DEEP MASS CONCRETE
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 45°
REFER TO NOTES

100
DOME TRUSS FREESTANDING OR N/A
BITUMEN PAINT ON 100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT
ALTERNATIVE PP PP PP COLUMN PP PP PP Ø300 x 1200 DEEP MASS CONCRETE PILE
STEEL NGL
150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS

75

300 MIN
B B B

0.25D
CONCRETE SLAB TRUSS
45°
PP PP PP PP

100
GABLE TRUSS PP PP PP PP COLUMN TO CONCRETE
NGL
EXISTING CONNECTION - 1:20

300 MIN
B B B B

1,200 MIN
0.25D
POOL
NOTES:
PP
- COLUMN FIXED TO CONCRETE SLAB WITH BEAM
2 x M12 STAINLESS STEEL DYNA BOLTS
THROUGH 2.0mm INTERNAL U-CLEAT. PURLIN
- COLUMN FIXED WITH 4 x 14 TEK SCREWS.
1200 MIN

EXISTING
3m MAX BEAM SPAN FOR HOUSE
PC PC PC PC
COLUMN FASCIA CONNECTION
PF PF PF PF

100
NGL
200SQ x 6PL PF
Ø 300

TYPICAL ELEVATION AT TRUSS (TR) - 1:100 END ELEVATION

NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE.
100

EXISTING FASCIA & GUTTER

Ø 300 3m MAX BEAM SPAN FOR
(ADD FASCIA PLATE) FASCIA CONNECTION
FIXING ON TOP OF EXISTING STEEL COLUMN/PILE FOOTING ADJACENT TO RETAINING
STEEL COLUMN/PILEPPFOOTING ADJACENT TOPPPOOL 1:20 CONCRETE SLAB - 1:20 1,000 1,000 WALL - 1:20 TRUSS
PP PP PP PP PP PP NOTE: TO REFER TO THE BASE FIXINGS TABLE MAX MAX
NOTE: DROP FOOTING TO SUIT IF THE POOL IS UNDER THE 45° LINE. CONTACT ENGINEER FOR NOTE: DROP FOOTING TO SUIT IF THE TOE OF THE RETAINING WALL IS UNDER THE 45° LINE.
ADVICE IF NEEDED. FOR SLAB THICKNESS. CONTACT ENGINEER FOR ADVICE IF NEEDED.

3m MAX BEAM SPAN

- 200SQ x 6PL: ALL OTHER PC PROVIDE MIN

END ELEVATION
PP 50SQ x 6PL.4M8 MASONRY ANCHORS. 40mm MIN
EMBEDMENT.
BEAM
BEAM

BEAM

BEAM

BEAM
EXTENSION OF PURLIN
PP PC & PEB
PATIO
SETBACK OF COLUMN
PC ON PEB OR TRUSS EXISTING
COLUMN PACKER
TO SUIT. HOUSE
PP NGL

PATIO COLUMN & PF PF

3c
NGL 1 x 150 LONG PATIO FOOTING)
¤
50
MIN

50 x 30 x 1.6mm ANGLE EXISTING

NGL
MIN
100

FIXED OR SIMILAR TO THE TRUSS RETAINING WALL

2cMIN
50 x 50 x 1.6 G.S.S. ANGLE
COLUMN WITH 2No. 14
x 150 LONG TO BE FIXED TO 150
TEKS END ELEVATION - OPTION POST EXTENSION/POST SETBACK

450 MAX
TYPICAL PLAN - 1:100
500

STUB COLUMN EXISTING

NOTES: USING 4 No.12 TEKS FOOTING
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS.
- STEEL GR350 FOR 76 x 38 x 1.2 / 1.6 MEMBERS, & GR450 DURAGAL FOR OTHERS U.N.O.

250MIN

=
¤ TRUSS
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS.
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE.
100

=
500
150
STANDARD OFFSET ALONG BOUNDARY BEAM
PE & CRITERIA PURLIN
TYPICAL STEEL COLUMN BASE FIXING DETAILS - 1:20
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO A PATIO COLUMN
SETBACK OF
FIXED TO EXISTING RETAINING WALL (ALTERNATIVE) - 1:20
ULAR HOUSE. NOTES: NOTES:
SIGN LOADINGS ARE AS/NZS PC ON BEAM
- TO REFER1170.
TO SCHEDULE FOR DIMENSIONS OF FOOTINGS. ¤ = 300 x 100 x 8PL FULLY WELDED TO REAR OF PC. FIX TO RETAINING WALL VIA 2M12 CHEMICAL ANCHORS, 150mm MIN EMBEDMENT
ORK TO COMPLY WITH BCA,
- STUB RELEVANT
COLUMN: SIZEAUSTRALIAN
TO MATCH PATIO COLUMN AND TO BE FULLY WELD ON BOTH SIDES. INTO EXISTING RETAINING WALL. LOCATE PLATE @ 450c/c MAX VERTICALLY.
NDARDS & STATUTORY REQUIREMENTS,
- OPTION: 50 x 50 x 1.6 OUTSIDE THISx 150 LONG TO BE FIXED TO STEEL COLUMN USING 4 No.12 TEKS.
G.S.S. ANGLE
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED.
PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS VOIDS THE PP - PATIO PURLIN
PEB - EDGE BEAM
TIFICATION. END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG, PC - PATIO COLUMN
PF - PATIO FOOTING
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 1:20
Scale: Sheet:
S1.1 Sheet:
S2.2
ionGSPublisherVersion
0.0.100.100 0.0.100.100
 PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS
PATIO COLUMN 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT
SKILLION 100 MIN ROOF AREA FOOTING SIZE (PC CAST IN) SLAB THICKNESS (PC FIXING ON TOP)
PATIO COLUMN
ALTERNATIVE 76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT 8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN UNREINFORCED SLAB
B PP B PP B
UPPER GL 90GL
UPPER x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m² 600 x 600 x 600 DEEP
NGLMASS CONCRETE 100mm MIN REINFORCED SLAB
100 x 50 x 2.0 SHS PATIOS (OR LARGER COLUMN FOR
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² 700 x 700 x 700 DEEP MASS CONCRETE N/A

3c
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 700 x 700 x 700 DEEP MASS CONCRETE
DOME TRUSS FREESTANDING OR N/A
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT
ALTERNATIVE PP PP PP PP PP PP Ø300 x 1200 DEEP MASS CONCRETE PILE
¤
E1 150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS

500 MIN

500 MIN
B B B

450 MAX
TRUSS 150
PP PP PP PP

75
2S12 CRANKED BARS @ 300c/c

600 MIN
GABLE TRUSS PP100 PP PP PP ¤

=
B B B B 150 x 100 x 6.0 EA

450 MAX
4M12 ANCHOR RODS.
PP GROUT 200 MIN
DRILL & EPOXY BEAM
CENTRALLY INTO EXISTING

=
LIMESTONE BLOCKS. PURLIN

700
200 ¤

100
4M12 ANCHOR RODS.

=
EXISTING
DRILL & EPOXY GROUT 200 MIN RETAINING NGL
CENTRALLY INTO EXISTING EXISTING
WALL HOUSE
PC PC PC PC
LIMESTONE BLOCKS. 3m MAX BEAM SPAN FOR

=
FASCIA CONNECTION ¤
75

PF PF PF PF
LOWER GL
350 (TYP)

EMBEDMENT
LOWER GL PF
(BEYOND) 75 75

250
600 MIN

TYPICAL ELEVATION AT TRUSS (TR) - 1:100 END ELEVATION

NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT 350
PARTICULAR
(TYP) SITE.
ELEVATION 1
EXISTING FASCIA & GUTTER 3m MAX BEAM SPAN FOR
PATIO COLUMN FIXED TO EXISTING
PATIO COLUMN/FOOTING SUPPORTED BY EXISTING LIMESTONE RETAINING WALL - 1:20
(ADD FASCIA PLATE) FASCIA CONNECTION RETAINING WALL - 1:20
NOTES: NOTES:
- PROPOSED STEEL PATIO POST & CONCRETE FOOTING MINIMUM TOTAL VOLUME TO BE AS PER ENGINEER PERTH PATIO DETAILS. ¤ = 300 x 100 x 8PL FULLY WELDED TO REAR OF PC. FIX TO RETAINING WALL
1,000 1,000
- CONCRETE FOOTING TO BE POURED IN DIRECT
PP CONTACT WITH HORIZONTAL
PP PP PP AND VERTICAL
PP SURFACES
PP PP OF PPRETAINING WALL. TRUSS
VIA 2M12 CHEMICAL ANCHORS, 150mm MIN EMBEDMENT INTO EXISTING
MAX MAX
- POUR FOOTING TO FULL DEPTH BEHIND WALL. RETAINING WALL. LOCATE PLATE @ 450c/c MAX VERTICALLY.
- NO SOIL ALLOWED BETWEEN UNDERSIDE OF FOOTING AND RETAINING WALL BLOCKS.

3m MAX BEAM SPAN

- CAST INTO FOOTING CRANKED S12 REINFORCING BARS @300c/c MAXIMUM FOR FULL DEPTH OF FOOTING, ENSURING COLUMN BASEPLATE OVERLAP.

END ELEVATION
- TIE CRANKEDPP
BARS TOGETHER WITH TRANSVERSE S12 BARS.
- CORROSION PROTECT BASE OF PATIO COLUMN COVERED BY SOIL WITH BITUMEN OR EPOXY PAINT.
BEAM
BEAM

BEAM

BEAM

BEAM
PATIO COLUMN PURLIN PATIO COLUMN
EXTENSION OF 200 x 90 x 10PL BASEPLATE. FULLY WELD TO PATIO POST.
PP PC & PEB
PATIO COLUMN PATIO COLUMN 2.0mm INTERNAL U-CLEAT
200 x 90 x 10PL BASEPLATE. SETBACK OF
FULLY WELD TO PATIO POST. PC ON PEB OR TRUSS EXISTING
(TYPICAL) HOUSE
UPPER GL UPPER GL
PP
2M12 ANCHOR RODS.
UPPER GL UPPER GL DRILL RECONSTITUTED LIMESTONE
2M12 ANCHOR RODS. PATIO COLUMN & BLOCKS & CHEMICAL ANCHOR
PF PF
DRILL RECONSTITUTED LIMESTONE PATIO FOOTING) RODS 600mm INTO WALL.

600

600
BLOCKS & CHEMICAL ANCHOR
RODS 600mm INTO WALL. TRUSS
600

600
TYPICAL PLAN - 1:100 E2 END ELEVATION - OPTION POST EXTENSION/POST SETBACK
NOTES:
E2

100
100
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS.
- STEEL GR350 FOR 76 x 38 x 1.2 / 1.6 MEMBERS, & GR450 DURAGAL FOR OTHERS U.N.O.
100
100

- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. LOWER TRUSS

EMBEDMENT
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE. GL LOWER GL
LOWER 150
EMBEDMENT

250
GL LOWER GL
150
250

BEAM
PE & CRITERIA PURLIN
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO A
ULAR HOUSE. SETBACK OF ELEVATION 2
PC ON BEAM
SIGN LOADINGS ARE AS/NZS 1170. ELEVATION 2
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS
PATIO COLUMN FIXED TO RECONSTITUTED LIMESTONE RETAINING / OPTION - 1:20
NOTES:
PATIO COLUMN FIXED TO RECONSTITUTED LIMESTONE RETAINING / OPTION - 1:20
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED.
- IN CASE OF HALF HEIGHT OR OTHER CAP BLOCK, MAINTAIN FULL ANCHOR ROD DEPTH. PP - PATIO PURLIN
ARTURE FROM THESE
NOTES: SPECIFICATIONS VOIDS THE PP - PATIO PURLIN
- MAXIMUM ROOF LOAD AREA TO EACH PC = 10m2. PEB - EDGE BEAM
TIFICATION. - IN CASE OF HALF HEIGHT OR OTHER CAP BLOCK, MAINTAIN FULL ANCHOR ROD DEPTH. END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM
- ALL STEELWORK TO BE GALVANISED. PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE- HAS TRUSS
MAXIMUM ROOF
ROOF & EAVES
LOAD AREAOVERHANG,
TO EACH PC = 10m2. PC - PATIO COLUMN
PF - PATIO FOOTING
ENGTHEN OVERHANG TO ACCEPT TO
- ALL STEELWORK LOADS FROM PATIO AS
BE GALVANISED. TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 1:20
Scale: Sheet:
S1.1 Sheet:
S2.3
ionGSPublisherVersion
0.0.100.100 0.0.100.100
 PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS
EXISTING ROOF FULLY WELD
SKILLION 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT ROOF AREA FOOTING SIZE (PC CAST IN) SLAB THICKNESS (PC FIXING ON TOP)
ALTERNATIVE 76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT 8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN UNREINFORCED SLAB
B PP B PP B PP PP
90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m² 600 x 600 x 600 DEEP MASS CONCRETE 100mm MIN REINFORCED SLAB
EXISTING ROOF 500 100 x 50 ROOF
EXISTING x 2.0 SHS 500 PATIOS (OR LARGER COLUMN FOR FIXING TO BRICKWORK
MAX 150 x 50 x 2.0 SHS MAX AESTHETIC REASONS) 20m² 700TO
REFER x 700 x 700 DEEP MASS CONCRETE
DETAIL N/A
OVERHANG OVERHANG
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 700 x 700 x 700 DEEP MASS CONCRETE
TIE DOWN TO OR
DOME TRUSS CB GTx TOP
100 100 xCHORD
3.0 SHS (G350) TO 6000 MAX HEIGHT FREESTANDINGSEPARATE DETAIL N/A
ALTERNATIVE PP PP PP PP PP PP Ø300 x 1200 DEEP MASS CONCRETE PILE
PP

MAX

MAX
EXISTING

300
300
B B B 150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS PC
HOUSE
PP
FIXING TO BRICKWORK FIXING TO BRICKWORK
GT BOTTOM CHORD
REFER TO DETAIL REFER TO DETAIL
TRUSS & WEB
2500 MAX
TIE DOWN TO PP PP PP PP TIE DOWN TO
SEPARATE DETAIL PP PP SEPARATE DETAIL
GABLE TRUSS PP PP 6000 MAX
EXISTING PC EXISTING PC
B HOUSE B B HOUSEB
PP
OPTION 1: CUT TRUSS - NTS
GT BOTTOM CHORD GT BOTTOM CHORD BEAM
& WEBS
PURLIN
FULLY WELD 1600 650 2250

6000 MAX 6000 MAX

EXISTING ROOF
EXISTING
3m MAX BEAM SPAN FOR HOUSE
PC PC PC PC
OPTION: RAISED GABLE - NTS FASCIA CONNECTION PP PP
PF PF PF PF
FIXING TO BRICKWORK
PF REFER TO DETAIL FULLY WELD

TIE DOWN TO
SEPARATE DETAIL
TYPICAL ELEVATION AT TRUSS (TR) - 1:100 END ELEVATION EXISTING PC
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE. HOUSE

EXISTING FASCIA & GUTTER 3m MAX BEAM SPAN FOR 6000 MAX
(ADD FASCIA PLATE) FASCIA CONNECTION

1,000 1,000
PP PP PP PP PP PP PP PP MAX MAX OPTION TRUSS
2: CUT TRUSS - NTS

3m MAX BEAM SPAN

FLASHING

END ELEVATION
PP
GUTTER
BEAM
BEAM

BEAM

BEAM

BEAM

10c MIN TO TOP OF WALL

(20c FOR SPANS > 6m)
PURLIN PURLIN PURLIN
EXTENSION OF PURLIN
TO REFER
PPTO NOTES TO REFER TO NOTES
PC & PEB
SETBACK OF
FASCIA BEAM
PC ON PEB OR TRUSS EXISTING
HOUSE
EDGEPP
BEAM
(WHERE APPLICABLE) ALTERNATIVE GT
ARRANGEMENT GUTTER
TRUSS TOP CHORD TO REFER TO PATIO
NOTESCOLUMN & PF PF TRUSS BOTTOM
ANGLE BRACKET PATIO FOOTING) CHORD
EDGE BEAM
TO REFER TO NOTES TRUSS BOTTOM TRUSS TOP CHORD
CHORD TRUSS
PATIO
Ø10 GALV. ROD IN PIER TRUSS TOP CHORD COLUMN
TYPICAL PLAN - 1:100
TO REFER TO NOTES MIN 190 x 290 END ELEVATION - OPTION POST EXTENSION/POST SETBACK
NOTES: BRICK PIER
TRUSS BOTTOM CHORD
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS.
- STEEL GR350 FOR 76 x 38 x 1.2 / 1.6 MEMBERS, & GR450 DURAGAL FOR OTHERS U.N.O.
PIER
- MIN ROOF SLOPE FIXING (ALTERNATIVE
TO MANUFACTURER'S TO STEEL COLUMN) - 1:20
SPECIFICATIONS. BRICK WALL CONNECTIONS - NO EAVES - 1:20 TRUSS
PC/PEB/GT CONNECTIONS - 1:20
- OPTION WITH NOTES:
EXTENSION AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE.NOTES: NOTES:
- ALTERNATIVELY FIX PURLINS TO FACE OF BEAM WITH INTERNAL - FIX GABLE TRUSS TO WALL USING SADDLE BRACKET. - ALTERNATIVELY PURLINS MAY BE FIXED TO FACE OF GT/CB WITH INTERNAL
BRACKETS. - FIX PURLIN TO GT VIA 1No.14 x 90 TEK OR VIA PURLIN BRACKET. BRACKETS.
- PIER MAY SUPPORT EDGE BEAM IF REQUIRED. FIX BRACKET TO EDGE - ALTERNATIVELY MITRE CUT & FULLY WELDED TOP CHORD IF PURLINS FIXED - FIX TRUSS DIRECTLY TO PATIO COLUMN (WITH INTERNAL BRACKET), IF NO EDGE
BEAM WITH 4 No. 14 TEK SCREWS. TO FACE OF GABLE TRUSS CHORD. BEAM. BEAM
PE & CRITERIA - Ø10 GALV. ROD IN PIER: THREAD AT TOP & FIX TO BRACKET OVER. COG - FIX PURLIN TO GT VIA 1No.14 x 90 TEK OR VIA PURLIN BRACKET.
PURLIN
- FIX TRUSS TO FASCIA BEAM WITH INTERNAL BRACKET.
S DESIGN APPLIES ROD
TO A 150mm
REGULARINTO FOOTING.
PATIO ALTERNATIVELY
ATTACHED TO A DRILL AND EPOXY GROUT
ULAR HOUSE. ROD 200mm INTO FOOTING BELOW. SETBACK OF - NOTCH PATIO COLUMN AND LEAVE FACE SHELL. FIX EDGE BEAM TO PATIO COLUMN
SIGN LOADINGS ARE- ANGLE
AS/NZSBRACKET:
1170. 100 x 75 x 5 PL x 75mm LONG. Ø10 ROD IN PIER. FIX PC ON BEAM WITH 4No. 12 TEKS (USE 14 TEK IF BEAM SPAN > 5.0m)
ORK TO COMPLY WITHWITH NUT
BCA, & WASHER.
RELEVANT FIX TO RAFTER VIA 4 No. 12 TEK SCREWS.
AUSTRALIAN
NDARDS & STATUTORY- FIXREQUIREMENTS,
PURLIN TO GT VIA 1No.14 xTHIS
OUTSIDE 90 TEK OR VIA PURLIN BRACKET.
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED.
PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS VOIDS THE PP - PATIO PURLIN
PEB - EDGE BEAM
TIFICATION. END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG, PC - PATIO COLUMN
PF - PATIO FOOTING
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 AS SHOWN
Scale: Sheet:
S1.1 Sheet:
S2.4
ionGSPublisherVersion
0.0.100.100 0.0.100.100
 PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS

4 No. SCREWS ON INTERNAL

SKILLION BRACKET 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT ROOF AREA FOOTING SIZE (PC CAST IN) SLAB THICKNESS (PC FIXING ON TOP)
45
TO CONTINUOUSALTERNATIVE
MEMBER 1.6 INTERNAL U-CLEAT
76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT 8m² 500 x 500 x 5002 DEEP
No.12MASS CONCRETE
TEKS/INTERFACE 75mm MIN UNREINFORCED SLAB
2 No. SCREWS ON EACH SIDE B PP B PP B
90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m² 600 x 600 x 600PURLIN
DEEP MASS CONCRETE 2 No.12
100mm MIN REINFORCED TEKS
SLAB
OF THE INTERSECTING MEMBER
100 x 50 x 2.0 SHS PATIOS (OR LARGER COLUMN FOR
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² 700 x 700 x 700 DEEP MASS CONCRETE N/A
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 100 700 x 700 x 700 DEEP MASS CONCRETE

TO SUIT
EXISTING RAFTER OR
DOME TRUSS 100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT FREESTANDING N/A 2 No.12 TEKS
ALTERNATIVE PP PP PP PP PP PP Ø300 x 1200 DEEP
SLOTMASS CONCRETE
COLUMN PILE PURLIN,
FOR TRUSS,
Ø10 THREADED ROD 150 TRUSS
B B B 150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS RAFTER/EDGE BEAM
TO REFER TO NOTES
NEW FASCIA
35 PLATE TRUSS
PP PP PP PP PLAN
INTERNAL BRACKET
GABLE TRUSS PP PP SADDLE
PP BRACKET PP 100
MIN
B NOTES: B B NOTES: B RAFTER BRACKET
- WIDTH AND HEIGHT
PP TO SUIT INTERNAL DIMENSIONS OF INTERSECTING - WIDTH AND HEIGHT TO SUIT DIMENSIONS OF INTERSECTING TRUSS/RAFTER, PURLIN & EDGE BEAM
MEMBER. MEMBER. BEAM
- USE 1.6mm THICK GALVANIZED STEEL PLATE. - USE 2.5mm THICK GALVANIZED STEEL PLATE.
NOTES:
- 50 x 6 PL x 600 LONG RAFTER BRACKET TO BE FIXED TO EXISTING
TO COLUMN CONNECTION - 1:20
- No. 10 TEK SCREWS (OR No. 12) TO BE USED FOR R (No. 14 TEK SCREWS IF - FIX SADDLE BRACKET TO WALL VIA 3M10 MASONRY PURLIN
NOTE: 90 x 2.0 SHS
RAFTER VIA 4 x TYPE 17 14 x 50.
RAFTER ANCHORS TO WALL. - Ø10 THREADED ROD: 100mm MIN. WELD TO 50 x 6PL. ONE NUT
> 4m). - FIX SADDLE BRACKET TO FASCIA PLATE VIA 4 No.12 TEKS INSIDE EXISTING FASCIA PLATE. ONE NUT OUTSIDE NEW FASCIA
- No. 10 TEK SCREWS (OR No. 12) TO BE USED FOR FIXING OF FB TO C (No. 14 (No.14 TEK SCREWS FOR RAFTER SPAN > 4m) PLATE. EXISTING
TEK SCREWS IF FB SPAN > 4m). - FIX SADDLE BRACKET TO BEAM VIA 2 No.12 TEKS ON EACH - OPTION: THE USE OF 50 x 6 PL x 750 LONG RAFTER BRACKET. 3m MAX BEAM SPAN FOR TRUSS /RAFTER HOUSE
PC- 2 No. 14 TEK SCREWS TO BE USED EACH
PC SIDE OF C FOR C TO SLAB PC SIDE OF BRACKET (No. 14 TEK FOR BEAM
PC SPAN > 4m)
FASCIA CONNECTION TOP CHORD
PF CONNECTION. PF PF PF
PURLIN/
EDGE BEAM
FIXING BRACKETS DETAILS - NTS PF
NOTES: 2 No.12 TEKS
- FABRICATE BRACKETS FROM 1.6 GSS, U.N.O.
- BRACKET DIMENSIONS TO SUIT THE MEMBERS BEING FIXED TO. 2 No.12 TEKS
TYPICAL ELEVATION AT TRUSS (TR) - 1:100 END ELEVATION
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE. INTERNAL U CLEAT
REFER TO NOTE

3m MAX BEAM SPAN FOR

COLUMN
EXISTING FASCIA & GUTTER NEW GUTTER 90 x 2.0 SHS
(ADD FASCIA PLATE) FASCIA CONNECTION
TRUSS TOP CHORD EXISTING ROOF
PURLIN RAFTER SECTION
1,000 1,000
PPTRUSSPP PP PP PP PP PP PP TRUSS
JOINTS MAX MAX
ALTERNATIVE GT
FULLY WELDED ARRANGEMENT
TRUSS/RAFTER, PURLIN & EDGE BEAM

3m MAX BEAM SPAN

TO REFER TO NOTES

END ELEVATION
PP
TRUSS BOTTOM CHORD
TO COLUMN CONNECTION - 1:20
NOTE: INTERNAL U CLEAT TO BE FIXED VIA 2No.12
BEAM
BEAM

BEAM

BEAM

BEAM
TEKS/INTERFACE
EXTENSION OF PURLIN
PP PC & PEB
SETBACK OF
PC/PEB/GT CONNECTIONS - NTS PC ON PEB OR TRUSS EXISTING
HOUSE
PP GT/CB
PATIO
PB/PEB COLUMN
PATIO COLUMN & PF PF
PATIO FOOTING)
GABLE TRUSS
BOTTOM CHORD
TRUSS
GABLE TRUSS FIX GT/PEB TO WALL
PC PB/PEB
TYPICAL PLAN - 1:100 TOP CHORD USING SADDLE BRACKET END ELEVATION - OPTION POST EXTENSION/POST
INT/EXT (SHOWN)
U CLEAT
SETBACK
INT/EXT (SHOWN)
NOTES: PATIO U CLEAT
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS. COLUMN
70 MAX

- STEEL GR350 FOR 76 x 38 x 1.2 / 1.6 MEMBERS, & GR450 DURAGAL FOR OTHERS U.N.O.
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. TRUSS
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE. PLAN ELEVATION
45° MIN

BRICK WALL CONNECTIONS (EAVES) - 1:20 ALTERNATEBEAM

TRUSS/RAFTER, PURLIN & EDGE BEAM TO
NOTES:
PE & CRITERIA MITRE CUT 700 MAX - FIX PURLIN TO GABLE TRUSS VIA 1 No. 14 x 90 TEK OR VIA PURLIN BRACKET. COLUMN CONNECTION
PURLIN - 1:20
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO A - ALTERNATIVE GABLE TRUSS ARRANGEMENT (MITRE CUT & FULLY WELDED) IF PURLINS FIXED NOTE: U CLEAT TO BE FIXED VIA 2No.12 TEKS/INTERFACE
ULAR HOUSE. PC SETBACK OF
TO FACE OF GABLE TRUSS CHORD. PC ON BEAM
SIGN LOADINGS ARE AS/NZS 1170.
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN
CRANKED POST
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED.
45° MIN ANGLE - 1:20
ARTURE FROM THESE SPECIFICATIONS VOIDS THE
PP - PATIO PURLIN
PP - PATIO PURLIN
PEB - EDGE BEAM
TIFICATION. END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG, PC - PATIO COLUMN
PF - PATIO FOOTING
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 AS SHOWN
Scale: Sheet:
S1.1 Sheet:
S2.5
ionGSPublisherVersion
0.0.100.100 0.0.100.100
 PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS

SKILLION 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT ROOF AREA FOOTING SIZE (PC CAST IN) SLAB THICKNESS (PC FIXING ON TOP)
ALTERNATIVE NEW GUTTER 76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT 8m² 500 x 500 x 500 DEEP MASS CONCRETE NEW GUTTER
75mm MIN UNREINFORCED SLAB
B PP B PP B
90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m² 600 x 600 x 600 DEEP MASS CONCRETE 100mm MIN REINFORCED SLAB
100 x 50 x 2.0 SHS PATIOS (OR LARGER COLUMN FOR
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² 700 x 700 x 700 DEEP MASS CONCRETE EXISTING ROOF N/A
EXISTING ROOF RAFTER
RAFTER 90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 700 x 700 x 700 DEEP MASS CONCRETE
DOME TRUSS FREESTANDING OR N/A
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT
ALTERNATIVE PP PP PP PP PP PP Ø300 x 1200 DEEP MASS CONCRETE PILE
B B B 150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS

600 MAX
GABLE TRUSS

600 MAX
TOP CHORD GABLE TRUSS
TOP CHORD
GABLE TRUSS TRUSS
BOTTOM CHORD GABLE TRUSS
PP PP PP PP BOTTOM CHORD
GABLE TRUSS PP PP PP PP

B B B B
PP
LATERALLY BRACE END BAYS TO
LATERALLY BRACE END BAYS TO BEAM
PREVENT SWAY ALONG PATIO.
PREVENT SWAY ALONG PATIO.
PURLIN
150 LONG 1.6 C CHANNEL
VIA 6 No.12 TEKS TO POLE
INTERNAL (SHOWN) /EXTERNAL/ PLATE
C BRACKET EXISTING
HOUSE
PC PC PC PCPOLE PLATE 3m MAX BEAM SPAN
FIX FORTO WALL
GT/PEB
NEW FASCIA PLATE FASCIA CONNECTION
PF 76 x 38 x 1.2 RHS PF PF PF USING SADDLE BRACKET

RAFTER BRACKET PF
TO REFER TO NOTES

OPTION FOR ROOF RISER -

TYPICAL ELEVATION
OPTION FORATROOF
TRUSS (TR) -- 1:100
RISER FIXED TO EAVES - 1:20 FIXED TO EAVE - NTS END ELEVATION
OPTION FOR ROOF RISER - FIXED TO BRICKWORK - 1:20
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE.
NOTES: NOTE: FIX PURLIN TO GABLE TRUSS WITH 1 No. 14 x 90 TEK OR WITH PURLIN BRACKET.
- FIX PURLIN TO GABLE TRUSS WITH 1 No. 14 x 90 TEK OR WITH PURLIN BRACKET.
- 600mm LONG RAFTER BRACKET: FIX TO EVERY 3RD EXISTING ROOF RAFTER WITH 3M-10
EXISTING
BOLTS. FIX THROUGH FASCIAAND
EXISTING & GUTTER
NEW FASCIA PLATE. 3m MAX BEAM SPAN FOR
(ADDRAFTER
- OPTION: 750mm LONG FASCIA BRACKET:
PLATE) FIX TO EVERY 2nd EXISTING ROOF RAFTER WITH 3- FASCIA CONNECTION
M10 BOLTS. FIX THROUGH EXISTING AND NEW FASCIA PLATE.
1,000 1,000
PP PP PP PP PP PP PP PP TRUSS
MAX MAX

3m MAX BEAM SPAN

END ELEVATION
PP

NEW GUTTER BEAM

BEAM

BEAM

BEAM

BEAM
NEW GUTTER
EXTENSION OF PURLIN
PP EXISTING ROOF EXISTING ROOF
RAFTER PC & PEB
RAFTER
SETBACK OF
PC ON PEB OR TRUSS EXISTING
HOUSE
GABLE TRUSS NEW 200 WIDE
PP
TOP CHORD BOX GUTTER
GABLE TRUSS
BOTTOM CHORD PATIO COLUMN & PF PFTRUSS
GABLE
PATIO FOOTING)
TOP CHORD
TRUSS GABLE TRUSS
BOTTOM CHORD

TYPICAL PLAN - 1:100

LATERALLY BRACE END BAYS TO
TRUSS
END ELEVATION - OPTION POST EXTENSION/POST SETBACK
PREVENT SWAY ALONG PATIO.
NOTES:
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS.
- STEEL GR350 FOR 76 x 38 x 1.2 / 1.6 MEMBERS, & GR450 DURAGAL FOR OTHERS U.N.O. LATERALLY BRACE END BAYS TO
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. PREVENT SWAY ALONG PATIO. TRUSS
INTERNAL/EXTERNAL/ C BRACKET 6 No.14 TEKS
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE. TO END CHANNEL
NEW FASCIA PLATE
76 x 38 x 1.2 RHS
TRUSS CONNECTION WITH EX 1.6 FIX GT/PEB TO WALL
BEAM
RAFTER BRACKET
PE & CRITERIA TO REFER TO NOTES
CHANNEL TO FASCIA PLATE - NTS USING SADDLE BRACKET
PURLIN
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO A
ULAR HOUSE. SETBACK OF
PC ON BEAM
SIGN LOADINGS ARE AS/NZS 1170. OPTION FOR ROOF OVERLAP - FIXED TO EAVES - 1:20
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN
OPTION FOR ROOF RISER - FIXED TO BRICKWORK - 1:20
NOTES: NOTE: FIX PURLIN TO GABLE TRUSS WITH 1 No. 14 x 90 TEK OR WITH PURLIN BRACKET.
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS
- FIX PURLIN TO GABLE TRUSS WITH 1 No. 14 x 90 TEK OR WITH PURLIN BRACKET.
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED.
- 600mm LONG RAFTER BRACKET: FIX TO EVERY 3RD EXISTING ROOF RAFTER WITH 3M-10 BOLTS. PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS VOIDS THE PP - PATIO PURLIN
FIX THROUGH EXISTING AND NEW FASCIA PLATE. PEB - EDGE BEAM
TIFICATION.
- OPTION: 750mm LONG RAFTER BRACKET: FIX TO EVERY 2nd EXISTING ROOF RAFTER WITH 3-M10 BOLTS. FIX THROUGH END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG, PC - PATIO COLUMN
PF - PATIO FOOTING
EXISTING AND NEW FASCIA PLATE.
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 AS SHOWN
Scale: Sheet:
S1.1 Sheet:
S2.6
ionGSPublisherVersion
0.0.100.100 0.0.100.100
 PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS

SKILLION 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT ROOF AREA FOOTING SIZE (PC CAST IN) SLAB THICKNESS (PC FIXING ON TOP)
ALTERNATIVE 76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT 8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN UNREINFORCED SLAB
B PP B PP B
NUT & WASHER EXISTING HOUSE 90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m² 600 x 600 x 600 DEEP MASS CONCRETE 100mm MIN REINFORCED SLAB
100 x 50 x 2.0 SHS PATIOS (OR LARGER COLUMN FOR TRUSS
REFER TO NOTES
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² 700 x 700BOTTOM
x 700 DEEP MASS CONCRETE N/A
CHORD
TRUSS BOTTOM 90 x 90 x 2.0 SHS (G350) TO 4500 MAX
EXISTING HEIGHT& FASCIA
GUTTER 700 x 700 x 700 DEEP MASS CONCRETE

4c MIN
CHORDDOME TRUSS FREESTANDING OR N/A
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT
ALTERNATIVE PP PP PP PP PP PP EXISTING ROOF Ø300 x 1200 DEEP MASS CONCRETE PILE
RAFTER BRACKET SADDLE BRACKET
B B B 150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS
RAFTER TO REFER TO DETAIL
REFER TO NOTES

150 LONG 1.6 C CHANNEL TRUSS EXISTING BRICKWALL

REFER TO NOTES
PP PP PP PP
POLE PLATEGABLE TRUSS PP PP PP PP

B B B B
PP
OPTION WITH C CHANNEL & FASCIA PLATE - NTS TRUSS
BEYOND
PATIOBEAM
BEAM/WALL CONNECTION
NOTES:
- NUT & WASHER: TO BE FIXED TO FRONT OF POLE PLATE AND BEHIND FASCIA.
ALTERNATE
PURLIN

- C CHANNEL: 150 LONG 1.6 C. TO BE FIXED TO POLE PLATE WITH 6No. 12 TEK SCREWS.
- RAFTER BRACKET: 50 x 6.0mm x 600mm. TO BE FIXED TO EXISTING TIMBER HOUSE
RAFTERS WITH 4 x TYPE 17 14 x 50 TEKS. EXISTING
3m MAX BEAM SPAN FOR HOUSE
PC PC PC PC
INTERNAL (SHOWN)/EXTERNAL/ FASCIA CONNECTION
PF PF PF PF
C BRACKET
NEW FASCIA PLATE PF
1120
76 x 38 x 1.2 RHS
TRUSS TOP CHORD
RAFTER BRACKET
TYPICAL ELEVATION AT TRUSS (TR) - 1:100 TO REFER TO NOTES END ELEVATION
TRUSS JOINTS
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE. FULLY WELDED
CLADDING
PURLINS
EXISTING FASCIA & GUTTER 3m MAX BEAM SPAN FOR
(ADD FASCIA PLATE) FASCIA CONNECTION TRUSS BOTTOM
PURLIN EAVES CONNECTION - STANDARD - 1:20 CHORD EXTENSION
NOTES:
TRUSS/RAFTER 1,000 1,000 1.6 INTERNAL U CLEAT
TRUSS/RAFTER PP PP PP PP - FIX BEAM TO NEW FASCIA PLATE WITH INTERNAL BRACKET. TRUSS
TOP CHORD PP PP PP PP MAX
- 600mm LONG RAFTER BRACKET: FIX TO EVERY 3RD EXISTING ROOF RAFTER WITH 3-M10
MAX REFER TO NOTE
BOLTS (1800 CRS MAX). FIX THROUGH EXISTING AND NEW FASCIA PLATE.

3m MAX BEAM SPAN

END ELEVATION
SECTIONPP PLAN
TYPICAL
BEAMCOLUMN TO TRUSS CONNECTION
BEAM

BEAM

BEAM

BEAM
TYPICAL PURLIN TO TRUSS/RAFTER CONNECTION - 1:20 EXTENSION OF
WITH PURLIN
BOUNDARY FRAME - 1:20
PPFIXED WITH 1.6 INTERNAL U CLEAT 2No. 12 TEKS / INTERFACE.
NOTE: PURLINS PC & PEB NOTE: COLUMN FIXED WITH 1.6 INTERNAL U CLEAT. 2 No.12 SCREW
TEKS/INTERFACE
SETBACK OF
PC ON PEB OR TRUSS EXISTING
HOUSE
PP

PATIO COLUMN & PF PF

PATIO FOOTING)
STITCH WELD 50mm IN FROM
TRUSS END THEN EVERY 1000mm
PATIO PURLIN (30mm WELDS)
TYPICAL PLAN - 1:100 PATIO
PURLIN
END ELEVATION - OPTIONTRUSS/RAFTER
POST EXTENSION/POST SETBACK
NOTES:
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN TO BE AS PER SEPARATE GABLE, EX. 1.6 (OR 2.0)
DOME AND FLAT PATIO DRAWING SETS.
- STEEL GR350 FOR 76 x 38 x 1.2 / 1.6 MEMBERS, & GR450 DURAGAL FOR OTHERS U.N.O. U CLEAT. EDGE BEAM
PATIO 1.6 GSS ANGLE TRUSS 1.6 INTERNAL U CLEAT
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS.
BEAM BRACKET. PATIO C-PURLIN REFER TO NOTES
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB ANDBEAM TRUSS CAN BE AT FRONT, REAR OR SIDE.
EX 1.6 / 2.0 / 3.0

RAFTER/TRUSS TO EDGE BEAM

BEAM
PE & CRITERIA PATIO BEAM UNDER PATIO PURLIN
CONNECTION - NTS
PATIO BEAM BETWEEN PATIO TYPICAL U NOTES: PURLIN
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO A PURLIN CLEAT/CAP PLATE - TRUSS/RAFTER TO BE NOTCHED TO SUIT EDGE BEAM &
ULAR HOUSE. SETBACK OF
PC ON BEAM FIXED WITH 1.6 INTERNAL U CLEAT.
SIGN LOADINGS ARE AS/NZS 1170.
PURLIN BRACKET DETAILS
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN DOUBLE C-PURLIN DETAIL - NTS - 2 No.12 TEKS/INTERFACE.
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED.
PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS VOIDS THE PP - PATIO PURLIN
PEB - EDGE BEAM
TIFICATION. END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG, PC - PATIO COLUMN
PF - PATIO FOOTING
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 AS SHOWN
Scale: Sheet:
S1.1 Sheet:
S2.7
ionGSPublisherVersion
0.0.100.100 0.0.100.100
 PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS

SKILLION 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT ROOF AREA FOOTING SIZE (PC CAST IN) SLAB THICKNESS (PC FIXING ON TOP)

BOUNDARY
BEAM BEAM
ALTERNATIVE 76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT 8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN UNREINFORCED SLAB
B PP B PP B WELD FLANGE TO FLANGE. STITCH
FULL EXTENSION SAME
2d x 300 x 1.6 STEEL PLATE 90 xSIZES.
90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 600 x 600 x 600 DEEP MASS CONCRETE 100mm MIN REINFORCED SLAB
WELD BETWEEN ALL BEAM 14m² SIZE AS BEAM
BOTH SIDES. 6N°10 TEK 100 x 50 x 2.0 SHS PATIOS (OR LARGER COLUMN FOR
SCREWS PER FACE. 150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² 700 x 700 x 700 DEEP MASS CONCRETE N/A
700 x 700 x 700 DEEP MASS CONCRETE

d
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT
DOME TRUSS FREESTANDING OR N/A
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT
ALTERNATIVE PP PP PP PP PP PP Ø300 x 1200 DEEP MASS CONCRETE PILE
BEAM B 150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS

d
B B EXTENSION SAME
300 3N° 50 x 150 x 1.6 GSS BOTH SIDES. 300
SIZE AS BEAM CONTINUOUS FILLET WELD.
EXTENSION SAME COLUMN TRUSS
300
SIZE AS BEAM PP PP PP PP
GABLE TRUSS PP PP PP PP

B EXTENDED PB/PC DETAILS

B - BOUNDARY B
EXTENDED
B
PB/PC DETAILS - BOUNDARY EXTENDED PB/PC DETAILS - BOUNDARY
EXTENSION
PP (NO ROOF) EXTENSION (NO ROOF) EXTENSIONBEAM
(NO ROOF)
NOTE: ALTERNATIVE 1 NOTE: ALTERNATIVE 2 NOTE: ALTERNATIVE 3
PURLIN

EXISTING
3m MAX BEAM SPAN FOR HOUSE
PC PC PC PC
FASCIA CONNECTION
PF PF PF PF

PF
100 BEAM
BEAM 1120 300 OR LARGER
1120 76 x 38 OR SIMILAR MAX MIN
MAX
TYPICAL ELEVATION AT TRUSS (TR) - 1:100 END ELEVATION
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE.

EXISTING FASCIA & GUTTER 3m MAX BEAM SPAN FOR

BOUNDARY
(ADD FASCIA PLATE) FASCIA CONNECTION
BOUNDARY

EXTENSION
1,000 1,000
PP PP PP EXTENSION SAME PP
PP PP PP PP TRUSS
MAX
76 x 38 MAX
SIZE AS BEAM COLUMN
COLUMN

3m MAX BEAM SPAN

END ELEVATION
PP

BEAM
BEAM

BEAM

BEAM

BEAM
ALTERNATE EXTENDED BEAM/COLUMN DETAILS - ALTERNATE EXTENDED BEAM/COLUMN DETAILS -
PURLIN
BOUNDARY
PP EXTENSION (NO ROOF) 1:10 BOUNDARY EXTENSION (NO ROOF) 1:10 EXTENSION
PC & PEB
OF

SETBACK OF
PC ON PEB OR TRUSS EXISTING
HOUSE
PP

PATIO COLUMN & PF PF

PATIO FOOTING)

TRUSS
SEAL END BEAM
INT/EXT
TYPICAL PLAN - 1:100 BEAM 1.6 U CLEAT END ELEVATION - OPTION POST EXTENSION/POST SETBACK
NOTES:
- BASES, CONNECTIONCOLUMN
DETAILS & DETAILS NOT SHOWN TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS.
- STEEL GR350 FOR 76 x 38 x 1.2 / 1.6 MEMBERS, & GR450 DURAGAL FOR OTHERS U.N.O.
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. TRUSS
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB EX. AND
2.5 TRUSS CAN BE AT FRONT, REAR OR SIDE.
U CLEAT. EX 3.0 CAP
PLATE
COLUMN

BEAM
SHS RHS
PE & CRITERIA PURLIN
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO A
ULAR HOUSE. ALTERNATE BEAM/SHS OR RHS
SETBACK OF
PC ON BEAM
SIGN LOADINGS ARE AS/NZS 1170.
BEAM/COLUMN
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN
BEAM/COLUMN COLUMN CONNECTIONS- NTS
CONNECTION
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS CONNECTION ALTERNATE
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED.
PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS VOIDS THE PP - PATIO PURLIN
PEB - EDGE BEAM
TIFICATION. END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG, PC - PATIO COLUMN
PF - PATIO FOOTING
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 AS SHOWN
Scale: Sheet:
S1.1 Sheet:
S2.8
ionGSPublisherVersion
0.0.100.100 0.0.100.100
 PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS

76 x 38 x 1.2 PATIO TUBE TRUSS

TO 3000 MAX(GT) 4000 MAX SPAN
HEIGHT TRUSS (GT) 5000 MAX SPAN
SKILLION
4000 MAX ROOF AREA FOOTING SIZE (PC CAST IN) SLAB THICKNESS (PC FIXING ON TOP)
ALTERNATIVE 76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT
4000 MAX 8m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN UNREINFORCED SLAB
B PP B PP B AS TOP CHORD
= 90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m² 600 x 600 x 600 (OR
DEEP
75MASS
x 50 xCONCRETE
1.6 DURAGAL RHS 100mm MIN REINFORCED SLAB
= = = 100 x 50 x 2.0 SHS 76 xCOLUMN
38 x 1.6 FOR
= PATIOS (OR LARGER IF WEBS INCLUDED)
= PP PP = = PP PP
150 x 50 x 2.0 SHS AESTHETICPATIO TUBE
REASONS) 20m² 700 x 700 x 700 DEEP MASS CONCRETE N/A
PP PP PP PP

HT
W
PP
W
PP PP PP 90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 700 x 700 x 700 DEEP MASS CONCRETE
≈ 250

HT
BC BC
TCDOMETRUSS
TC
TC
TC ≈ 200 FREESTANDING OR 1/4 HT N/A
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT TC TC
ALTERNATIVE PP PP PP 1
/4 HT TC Ø300 x 1200 DEEP MASS CONCRETE PILE
PP PP PP
FIXING TO TC
B B B 150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS
BRICKWORK 4000 MAX 5,000 MAX
1000 1000 1000
MAX MAX MAX EXISTING
PC PC PC
HOUSE TRUSS TOP CHORDS (TC) TOP CHORDS (TC)
PP PP PP PP
76 x 38 x 1.6 76 x 38 x 1.6 76 x 38 x 1.6 75 x 50 x 1.6 75 x 50 x 1.6 75 x 50 x 2.0
GABLE TRUSS PP PP PP PP PATIO TUBE PATIO TUBE PATIO TUBE DURAGAL RHS DURAGAL RHS DURAGAL RHS
TRUSS (GT) 4000 MAX SPAN TRUSS (GT) 4000 MAX SPAN
B B B B 2000 MAX SPAN 3000 MAX SPAN 4000 MAX SPAN 2000 MAX c/c 3000 MAX c/c 4000 MAX c/c
BC = BOTTOM CHORD 76 x 38 x 2.0 PATIO TUBE BC = BOTTOM CHORD 76 x 38 x 2.0 PATIO TUBE
PP
TC = TOP CHORD 76 x 38 x 1.6 PATIO TUBE TC = TOP CHORD 76 x 38 x 1.6 PATIO TUBE BEAM
W = WEBS 76 x 38 x 1.6 PATIO TUBE OR 30 x 30 x 1.6 DURAGAL SHS W = WEBS 76 x 38 x 1.6 PATIO TUBE OR 30 x 30 x 1.6 DURAGAL RHS
PC MAY BE MOVED UP TO 1000 MAX. PC MAY BE MOVED UP TO 1000 MAX. PURLIN
TRUSS (GT) 6000 MAX SPAN TRUSS (GT) 6000 MAX SPAN

AS TOP CHORD = = EXISTING

= = = = = =
PP PP PP PP (OR 75 x 50 x 1.6 DURAGAL RHS 3m MAX BEAM SPAN FOR HOUSE
PC TC PC TC PC TC PC PP TC
IF WEBS INCLUDED)
PF PP
PP
W W PFW
PP
PP PF PP
PP
W W PF W PP
FASCIA CONNECTION A
W

HT
PP 30° PP PP 30° PP TC

HT
≈ 300 TC W W
PEB/PP BC PEB/PP PEB/PP BC PF W W
1
/4 HT 1
/3 HT W BC W
FIXING TO TC TC
BRICKWORK
X
MA
1000 1000 1000 6,000 MAX 150
TYPICAL ELEVATION AT TRUSS (TR) - 1:100
PC
MAX MAX PC PC
MAX EXISTING END ELEVATION
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE. HOUSE
190MAX 6,000 MAX

END TRUSS (GT) TOP CHORDS (TC) TRUSS (GT) TO 6000 MAX SPAN
EXISTING FASCIA & GUTTER END TRUSS (GT) 3m MAX BEAM SPAN FOR
BC = BOTTOM CHORD (ADD
ASFASCIA PLATE)
PER TABLE 100 x 50 x 1.6 100 x 50 x 2.0 FASCIA
100 xCONNECTION
50 x 2.5 TC 76 x 38 x 1.6 PATIO TUBE
BC = BOTTOM CHORD AS PER TABLE DURAGAL RHS DURAGAL RHS DURAGAL RHS
TC = TOP CHORD 76 x 38 x 1.6 PATIO TUBE TC = TOP CHORD 76 x 38 x 1.6 PATIO TUBE W 35 x 35 x 1.6 DURAGAL SHS
W = WEBS 76 x 38 x 1.6 PATIO TUBE OR 30 x 30 x 1.6 DURAGAL SHS W = WEBS 76 x 38 x 1.6 PATIO TUBE OR 30 x 30 x 1.6 DURAGAL RHS 1,000 3000
2000 MAX c/c 1,000
MAX c/c 4000 MAX c/c BC 35 x 35 x 1.6 DURAGAL SHS
PC MAY BE MOVED UP TO 1000 MAX. PP PP PP PP PC
PP MAY BE
PPMOVED
PP UPPP
TO 1000 MAX. TRUSS
MAX MAX

3m MAX BEAM SPAN

TRUSS (GT) 7000 MAX SPAN TRUSS (GT) 8000 MAX SPAN

END ELEVATION
PP
PP PP PP PP
TC TC TC TC
BEAM
BEAM

BEAM

BEAM

BEAM
PP PP PP PP
PP
W W W
PP PP
W W W
PP = = = = = = = = = = = = = = =
PP W W PP PP W W PP EXTENSION OF PURLIN
250

40 BC
PEB/PP 400 PP BC
MA 0 PEB/PP
A PC & PEB
MA
X X PEB/PP 400
MA
X FIXING TO SETBACK OF
W2
TC A TC W2
TC
TC W1 W1

HT
BRICKWORK PC ON PEB OR TRUSS EXISTING

HT
W1 W1 W1 W1
1000 1000 1000
EXISTING
1
/3 HT W1 W1 W2 HOUSE W2
MAX W2 W2 1
/3 HT
MAX PP MAX HOUSE
PC PC PC BC
X BC
MA X
150 MA
PATIO COLUMN & PF PF 150
INNER TRUSS (GT) INNER TRUSS (GT) PATIO FOOTING)
190 MAX 7,000 MAX 190 MAX 8,000 MAX
BC = BOTTOM CHORD AS PER TABLE BC = BOTTOM CHORD AS PER TABLE TRUSS
TC = TOP CHORD 76 x 38 x 1.6 PATIO TUBE TC = TOP CHORD 76 x 38 x 1.6 PATIO TUBE
W = WEBS 76 x 38 x 1.6 PATIO TUBE OR 30 x 30 x 1.6 DURAGAL RHS
TYPICAL PLAN - 1:100
W = WEBS 76 x 38 x 1.6 PATIO TUBE OR 30 x 30 x 1.6 DURAGAL SHS
PC MAY BE MOVED UP TO 1000 MAX. PC MAY BE MOVED UP TO 1000 MAX. ENDTRUSS
ELEVATION - OPTION
(GT) TO 7000 MAX SPAN POST EXTENSION/POST SETBACK
TRUSS (GT) TO 8000 MAX SPAN
NOTES: TC 75 x 50 x 1.6 DURAGAL RHS TC 75 x 50 x 1.6 DURAGAL RHS
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS. 40 x 40 x 2.0 DURAGAL SHS OR W1 50 x 50 x 2.0 DURAGAL SHS
W1
- STEEL GR350 FOR 76 x 38 x 1.2 / 1.6 MEMBERS, & GR450 DURAGAL FOR OTHERS U.N.O. 50 x 50 x 1.6 DURAGAL SHS W2 50 x 50 x 1.6 DURAGAL SHS
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. TRUSS
FREESTANDING ATTACHED
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE. W2
40 x 40 x 1.6 DURAGAL SHS OR BC 50 x 50 x 1.6 DURAGAL SHS
50 x 50 x 1.6 DURAGAL SHS
40 x 40 x 1.6 DURAGAL SHS OR
BC
50 x 50 x 1.6 DURAGAL SHS 190
CURVED BOTTOM CHORD OPTION A CURVED BOTTOM CHORD OPTION B DETAIL A - 1:50
BEAM MAX
PE & CRITERIA NOTE: FOR 50 MIN WELD LENGTH USE
90° PURLIN 4mm WELD OR FOR 70 MIN WELD LENGTH
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO A WELD USE 3mm WELD.
ULAR HOUSE. SETBACK OF 150 X WELD BOTH SIDES.
SIGN LOADINGS ARE AS/NZS 1170. PC ON BEAM MA
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED.
TRUSS DETAILS
NOTES: PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS
OPTIONAL WEB LAYOUTSVOIDS THE PP - PATIO PURLIN
- ALL JOINTS FULLY WELDED U.N.O. PEB - EDGE BEAM
TIFICATION.
NOTES: END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM
- TRUSS CHORD SLOPE 15° - 25° PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS
- WEBS MAYROOF & EAVES
BE ADDED OVERHANG,
IN IF REQUIRED. - REFER TO GABLE OR HIP PYRAMID DETAIL SHEETS PC - PATIO COLUMN
PF - PATIO FOOTING
ENGTHEN OVERHANG- ALLTO ACCEPT
WEBS 35 x LOADS
35 x 1.6 FROM
SHS. PATIO AS TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 NTS
Scale: Sheet:
S1.1 S2.9
Sheet:

ionGSPublisherVersion
0.0.100.100 0.0.100.100
 PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS PATIO FOOTINGS

SKILLION 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT ROOF AREA FOOTING SIZE (PC CAST IN) SLAB THICKNESS
PAD FOOTING (PCSPACING
FRAME FIXING ON TOP)
LOCATION
ALTERNATIVE EXISTING RESIDENCE 76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT
EXISTING FASCIA PLATE 8m² 500 x 500 x 500 DEEP MASS
PF1 CONCRETE 75mm MIN UNREINFORCED SLAB
450mm CUBED
B PP B PP W/BNEW FASCIA PLATE 2 N/A END COLUMNS
90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m² 600 x 600 x 600 DEEP MASS CONCRETE (0.10 m100mm
) MIN REINFORCED SLAB
100 x 50 x 2.0 SHS PATIOS (OR LARGER COLUMN FOR 600mm CUBED INTERMEDIATE
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² 700 x 700 x 700 DEEP MASS
PF2 CONCRETE N/A3m

F1

F1
(0.22 m2) COLUMN

/P

/P
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 700 x 700 x 700 DEEP MASS CONCRETE

C
8,000 MAX OR PF2 700mm CUBED INTERMEDIATE
DOME TRUSS 100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT FREESTANDING N/A4m
F1
2 COLUMN

F1
ALTERNATIVE PP PP PP PP Ø300 x 1200 DEEP MASS CONCRETE PILE (0.34 m )
/P
PP PP

/P
C

C
B B B INFILL PANEL WITH 150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS NOTES: IF ROOF AREA TO COLUMNS VARIES, INCREASE/DECREASE THE
OPTIONAL ROLLER DOORS CONCRETE VOLUME IN BASE PRO RATA.

RB

R
TRUSS

RB
G

8,000 MAX
COLUMN (C) W/ PATIO FOOTING

R
PP PP PP PP REFER TO TABLE FOR DIMENSIONS
C 1
C
W PF

ROOF ALTERNATIVES
/D

GABLE TRUSS PP PP PP PP
E1 G

F2

F2
CUSTOM ORB PURLINS
B B B B

C 1
MIN. SLOPE TO BE 5°

/P

/P
C
W PF
ROOF 900 END SPANS, 1200 INTERNAL

/D

C
PP
BEAM
PURLINS
C 1
C

TRIMDEK ROOF
W PF

MIN. SLOPE TO BE 2°
/D

G EP PURLIN 1200 END SPANS, 1800 INTERNAL

TRUSS EP G
REFER TO STANDARD PATIO DETAILS
EP EXISTING
3m MAX BEAM SPAN FOR HOUSE

F1
PC PC G PC PC
C R

C R

C R
F1

F2

F2

/P
D CO

D CO

D CO
FASCIA CONNECTION

C
/P

/P

/P
PF PF PF PF TYPICAL DIMENSIONS

F2

F2
/P

/P
WB ON ANY BAY THIS SIDE (EXCEPT WHERE ROLLER DOOR)

C
PF
REFER TO NOTES WC 76 x 38 x 1.6 PATIO TUBE
RB R
R 3m MAX HEIGHT & 3m MAX SPACING
INFILL PANEL WITH RB
50 x 38 x 1.6 PATIO TUBE
OPTIONAL ROLLER DOORS
TYPICAL ELEVATION AT TRUSS (TR) - 1:100 END ELEVATION C
3m MAX HEIGHT & 4m MAX SPACING
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE. 75 x 50 x 1.6 DURAGAL GR450

4,000 MAX 4,000 MAX 4,000 MAX 76 x 38 x 1.6 RHS

3m MAX BEAM SPAN FOR G
EXISTING FASCIA & GUTTER (OR MONOSPAN TO 3.5m SPAN)
(ADD FASCIA PLATE) FASCIA CONNECTION
RBR

F1

F1
E3 G HOOP IRON OR SPEED BRACE

C 1

C 1
MAX 4 BAYS OF 3,000 OR 3 BAYS OF 4,000 MAX

/P

/P
C

C
W PF

W PF
/D

/D
C

C
WB HOOP IRON
E2 1,000 1,000
PP PP PP PP PP PP PP PP TRUSS DC 100 x 50 x 2.0 RHS
MAX MAX
TR REFER TO GABLE DETAILS
TYPICAL PLAN, SINGLE SKIN & SOLARSPAN INSULATED WALLS - SIDE ATTACHED TYPICAL PLAN

3m MAX BEAM SPAN

NOTES: REFER TO GABLE STANDARD DETAILS FOR TRUSS & CONNECTION

END ELEVATION
NOTES: PP
- INSULATED PANELS ARE TO BE INSTALLED TO MANUFACTURER'S SPECIFICATION.
END ATTACHED DETAILS.
- SOLARSPAN INSULATED PANELS: 50mm, 75mm OR 100mm. BEAM
BEAM

BEAM

BEAM

BEAM
- PATIO ROOF ATTACHED TO RESIDENCE AS PATIO STANDARD DETAILS. TR
- WB TO BE HOOP IRON EXTENSION OF PURLIN

F1

F1

F1

F1
- LOCATION OF DOORPP COLUMN (DC) ONLY IF ROLLER DOOR. PC & PEB

/P

/P

/P

/P
C

C
- PATIO WITH BATTEN END TRUSSES AND SHEET GABLE ENDS.

D
SETBACK OF
PC ON PEB OR TRUSS EXISTING
OPTION WITH ROLLER DOORS HOUSE
PP
8,000 MAX 8,000 MAX TRUSS (TR)
REFER TO STANDARD PATIO
PATIO COLUMN & PF PF DETAILS
PATIO FOOTING)
PURLIN INNER TRUSS INNER TRUSS EP W/ GUTTER
TO REFER TO NOTES TRUSS
OUTER TRUSS OUTER TRUSS

TYPICAL PLAN - 1:100 EP W/ GUTTER EP W/ GUTTER END ELEVATION - OPTION POST EXTENSION/POST SETBACK
EXISTING
EP COLUMN
NOTES: FIXING TO COLUMN COLUMN
RESIDENCE WB
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN TO BE AS PER SEPARATE GABLE, DOME AND FLAT
BRICKWORK C PATIO DRAWING SETS. G G G G WB G
INFILL W/ OPTIONAL
- STEEL GR350 FOR 76 x 38 x 1.2 / 1.6 MEMBERS, & GR450 DURAGAL FOR OTHERS U.N.O. INFILL W/ OPTIONAL
INFILL
- MIN ROOF
FASCIASLOPE
PLATE TO MANUFACTURER'S SPECIFICATIONS. ROLLER DOOR ROLLER DOOR TRUSS
REFER
- OPTION TOEXTENSION
WITH NOTES G G
AND SETBACK OF PC ON PEB ANDGTRUSS
G CAN BE AT FRONT, REAR OR SIDE.G G G G
G G G G G
COLUMN WC OR DC WC OR DC

1
PF

PF

PF

PF
G G G G
BEAM
INFILL W/ OPTIONAL
1

PE & CRITERIA
PF

PF

PF

PF

PF

PF

PF

PF

PURLIN ROLLER DOOR

S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO A
ULAR HOUSE. SETBACK OF
SIGN LOADINGS ARE AS/NZS 1170. PC ON BEAM
ELEVATION 1 AND ELEVATIONS 2 - SIDE AND END ATTACHED
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN ELEVATION 3 - END ATTACHED PF - PATIO FOOTING
NDARDS & NOTES:
STATUTORY REQUIREMENTS, OUTSIDE THIS NOTES: C - COLUMN
- PATIO
PE INDIVIDUAL FIXED TO EXISTING
ENGINEERING DESIGNHOUSE.
IS REQUIRED. - PATIO FIXED TO EXISTING HOUSE. EP - EDGE PURLIN
-
ARTURE FROM FIXING TO FASCIA
THESE PLATE AS VOIDS
SPECIFICATIONS PATIO STANDARD
THE DETAILS. - FIXING TO FISCIA PLATE AS PATIO STANDARD DETAILS. G - GIRT
- COLUMNS TO BE BUILT 400 MIN INTO BASE & ANCHOR. PP - PATIO
TRPURLIN
- TRUSS
TIFICATION.
- PURLIN: DEFLECTION LIMIT UNDER DEAD LOAD ONLY TO BE: SPAN END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM
- COLUMNS TO BE BUILT 400 MIN INTO BASE & ANCHOR.
PF - PATIO
RBFOOTING
- ROOF BEAM
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG, PC - PATIO COLUMN
WC - WALL COLUMN
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS 200 TR - TRUSS
DC – DOOR COLUMN
UIRED BY TRUSS MANUFACTURER. B - BEAM WB – WALL BRACE
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 NTS
Scale: Sheet:
S1.1 S2.10
Sheet:

ionGSPublisherVersion
0.0.100.100 0.0.100.100
 PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS CENTRAL TRUSS
MEMBERS TRUSS SPAN TRUSS RAFTER COLLAR TIE CONNECTION
SKILLION 76 x 38 x 1.2 PATIO TUBE
1. GENERAL TO 3000 MAX HEIGHT ROOF AREA 3m IN)
FOOTING SIZE (PC CAST 120 x 35 MGP10
SLAB 90(PC
THICKNESS x 35 FIXING
MGP10 ON TOP)2M10 BOLTS
ALTERNATIVE a) ALL MGP10 MEMBERS TO BE MINIMUM JOINT GROUP JD4 U.N.O. 4m 140 x 35 MGP10 120 x 35 MGP10 2M10 BOLTS
76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT 500 x 500 x 500 DEEP MASS5mCONCRETE190 x 45 MGP10
75mm MIN UNREINFORCED SLAB
B PP
SIMILAR TO TIMBER POST
B PP& TRUSS B b) ALL BOLTS AND FIXING RODS TO BE HOT DIP GALVANIZED TO8m² AS4680. 120 x 35 MGP10 2M12 BOLTS
REFER TO POST, FASCIA BEAM 90 x 90 x 2.0 SHS (Gr450)
c) ALL TO 4000
GL MEMBERS TOMAX HEIGHTPINE
BE 'AUSTIM & FREESTANDING JOINT GROUP600
GLULAM' (GL18) WITH MIN14m² JD4x 600 x 600 DEEP MASS CONCRETE
U.N.O. 100mm MIN REINFORCED SLAB
CONNECTION DETAILS 100 x 50 x 2.0 SHS
2. POSTS PATIOS100SQ
- TO BE MINIMUM (OR LARGER
MGP10.COLUMN FOR
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² 700 x 700 x 700 DEEP MASS CONCRETE N/A
3. TRUSS FASCIA BEAM TABLE
90 x 90 x 2.0 -SHS (G350)120 x 35 MGP10TO
PROVIDE TRUSS TRIMMERS/NOGGINGS
4500 MAX HEIGHT TO BOTTOM CHORD OF700 x 700AT
TRUSS x 700
1800DEEP MASS CONCRETEBEAM SPAN KAPUR GLULAM AUSTIM GLULAM
DOME TRUSS CRS MAX AND USE 120 x 35 MGP10 FOR ALL TRUSS MEMBER.FREESTANDING OR N/Ax 60
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT UP TO 3500 198 231 x 65
NOTCH POLE ALTERNATIVE PP PP PP PP PP PP - ALL FIXED USING PRYDA KNUCKLE NAILPLATES ON BOTH SIDES (OR DIFFERENT Ø300 x 1200 DEEP
PRODUCT WITHMASS CONCRETE PILE
REFER TO NOTES 150 x 50 x 3.0 EQUIVALENT
SHS (Gr450) CAPACITY).
WHEN ADDING SOLAR PANELS UP TO 5000 264 x 60 297 x 65
B B B
- REFER TO TABLE FOR DIMENSIONS.
4. BATTENS - 70 x 45 MGP10. TO PROVIDE SPACE TO SUIT CLADDING (1200 CRS MAX).
5. KNEE BRACE - 120 x 35 MGP10. TRUSS
6. FASCIA BEAM - REFER TO FASCIA BEAM TABLE.
PP PP PP PP
7. ALL FIXING BRACKETS TO MANUFACTURER'S DETAILS.
GABLE TRUSS PP PP PP PP
8. COLUMN AND FRAME ARE SATISFACTORY PROVIDED THAT THE FRAME IS BRACED AGAINST SWAY,
B B B B BY THE BUILDING OR WITH ADDED KNEE BRACING.
PP

MAX HEIGHT
BEAM

3,500
PURLIN
Ø 200mm BUSH POLE

TYPICAL POST SHOE EXISTING

3m MAX BEAM SPAN FOR HOUSE
PC REFER TO NOTES PC PC PC
FASCIA/ CONNECTION
RAFTER TRUSS
PF PF PF PF
2-M12 BOLTS
THROUGH BUSH POLE RAFTER / TRUSS PF BATTENS @ 1200c/c MAX TYPICAL
SLAB/PAVING FIX TO EVERY RAFTER/TRUSS
REFER TO NOTES BATTENS @ 1200c/c MAX TYPICAL
FIX TO EVERY RAFTER/TRUSS
TYPICAL ELEVATION AT TRUSS (TR) - 1:100 END ELEVATION
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE.
NGL TRUSS FIXING TO TOP OF FASCIA BEAM VIA
2Nº PRYDA MULTIGRIPS OR EQUIVALENT
2-M16 EXISTING FASCIA & GUTTER TRUSS FIXING TO FACE OF FASCIA BEAM VIA 3m MAX BEAM SPAN FOR
(ADD FASCIA PLATE) 2Nº PRYDA MULTIGRIPS OR EQUIVALENT FASCIA CONNECTION
NOTCH POST (NO MORE THAN HALF) AND FIX TO NOTCH POST (NO MORE THAN HALF) AND FIX
CONCRETE FOOTING FASCIA BEAM OVER WITH 2M12 BOLTS TO FASCIA BEAM OVER WITH 2M12 BOLTS
REFER TO TABLE 1,000 1,000
PP PP PP PP PP PP PP PP TRUSS
MAX MAX

3m MAX BEAM SPAN

END ELEVATION
PP

BUSH POLE DETAIL - 1:20 BEAM

BEAM

BEAM

BEAM

BEAM
NOTES: POST, FASCIA BEAM & TRUSS CONNECTION - 1:20
- 2-M16 MEDIUM DUTY ANCHORS TO BE USED TO BOLT POST SHOE TO FOOTING. EXTENSION OF PURLIN
(ALTERNATIVE)
PP PC & PEB
- SLAB OR PAVING WHEN APPLICABLE: BOTTOM OF POST TO BE AT THE SAME LEVEL. IF NO PAVING, NOTE: SIMILAR CONNECTION WHEN USING BUSH POLE.
BOTTOM OF POST TO BE MIN. 30mm ABOVE GROUND LEVEL. SETBACK
BUILD OF
UP FOOTING
- NOTCH POLE TO BE NO MORE THAN HALF WIDTH OF THE BUSH POLE. TO BE FIXED VIA 2-M12 BOLTS. PC ON PEB
ABOVE OR TRUSS
GROUND AND EXISTING
SLOPE TO PREVENT HOUSE
PP MOISTURE COLLECTION
100 x 100
TIMBER POST
PATIO COLUMN & PF PF

MIN
PATIO FOOTING)

75
NGL
TRUSS
100 x 100
END ELEVATION - OPTION POST EXTENSION/POST SETBACK

500 MIN
TYPICAL PLAN - 1:100 Ø12 GALV DOWEL ROD TIMBER POST
NOTES: ACROSS POST
METAL STIRRUP FIXED
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS. TO TIMBER POST VIA
- STEEL GR350 FOR 76 x 38 x 1.2 / 1.6 MEMBERS, & GR450 DURAGAL FOR OTHERS U.N.O. 2M10 BOLTS
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. TRUSS
MASS CONCRETE PAVING OR GRANO TO
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE. FOOTING PAD SIZE AS BUILDERS DETAIL
PER FOOTING TABLE 75mm CLEARANCE

BEAM
PE & CRITERIA PURLIN
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO A POST FOOTING - 1:20 MASS CONCRETE 2M16 MEDIUM DUTY
ULAR HOUSE. (FREESTANDING OR NON FREESTANDING STRUCTURE) SETBACK OF REFER TO TABLE FOR ANCHORS TO FOOTING
SIGN LOADINGS ARE AS/NZS 1170. PC ON BEAM FOOTING SIZE
NOTES:
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN - REFER TO S2.1 WHEN FOOTING ADJACENT TO POOL OR RETAINING WALL.
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS - SIMILAR CONNECTION WHEN USING BUSH POLE.
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED.
PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS VOIDS THE
PEB - EDGE BEAM POST FOOTING - 1:20 (ALTERNATIVE) PP - PATIO PURLIN
TIFICATION.
PC - PATIO COLUMN END ELEVATION - OPTION POST SETBACK
NOTE: ANDSTRUCTURE
NON FREESTANDING FIXED ON
ONLYBEAM PF - PATIO FOOTING
EXISTING
PF - HOUSE HAS TRUSS ROOF & EAVES OVERHANG,
PATIO FOOTING PC - PATIO COLUMN
ENGTHEN OVERHANG
GT - GABLE TO ACCEPT LOADS FROM PATIO AS
TRUSS TR - TRUSS
UIREDCBBY- TRUSS MANUFACTURER.
CRANKED BEAM B - BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 1:20
Scale: Sheet:
S1.1 S2.11
Sheet:

ionGSPublisherVersion
0.0.100.100 0.0.100.100
 PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS
PATIO CONDITIONS (TOPOGRAPHICAL FACTOR OF 1.0)

SKILLION 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT ROOF AREA FOOTING SIZE (PC CAST IN) FULL
CATEGORY SLAB THICKNESS (PC PARTIAL
FIXING ON TOP) NO
DIMENSIONS WHEN ADDING SOLAR PANELS ON ROOF
ALTERNATIVE 76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT 8m²
TERRAIN
500 x 500 x 500 DEEP MASS CONCRETE
CATEGORY - 3 75mm MIN UNREINFORCED SLAB
SHIELDING SHIELDING SHIELDING

NOTE: ALL CALCULATIONS WERE DONEBWITH THE PROVISOPP B

OF THE SOLAR PANELS PP
APPLYING A PRESSURE OF 0.12 kPa. B
90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m²
TERRAIN
600 x 600 x 600 DEEP MASS CONCRETE
TERRAIN CATEGORY - 2.5 100mm MIN REINFORCED SLAB
¸
100 x 50 x 2.0 SHS PATIOS (OR LARGER COLUMN FOR
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² 700 x 700 x 700 DEEP MASS CONCRETE
TERRAIN CATEGORY - 2 N/A
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 700 x 700 x 700 DEEP MASS CONCRETE
WIND REGION A - 1kN MAX POINT LOAD
DOME TRUSS FREESTANDING OR N/A
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT
ALTERNATIVE PP PP PP PP PP PP Ø300 x 1200 DEEP MASS CONCRETE PILE
B B B 150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS

TRUSS
PP PP PP PP
GABLE TRUSS PP PP PP PP
COLUMN (PC) BASE FIXINGS
CRANKED BEAMS (CB) MAX SPAN TABLE - 1kN MAX POINT LOAD
B B B B
90 x 38 x 1.6 75 x 50 x 1.6 75 x 50 x 2.0 75 x 50 x 3.0 100 x 50 x 1.6 100 x 50 x 2.0 100 x 50 x 3.0 150 x 50 x 2.0 ROOF AREA FOOTING SIZE (PC CAST IN) SLAB THICKNESS (PC FIXING ON TOP)
PP
PATIO TUBE DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS BEAM
6.4m² 500 x 500 x 500 DEEP MASS CONCRETE 75mm MIN UNREINFORCED SLAB
RLW = 1800 3000 3300 3000 3200 3700 4100 4400 5000 PURLIN
11m² 600 x 600 x 600 DEEP MASS CONCRETE 100mm MIN REINFORCED SLAB
RLW = 2400 2900 3200 2900 3200 3600 3900 4200 4800
16m² 700 x 700 x 700 DEEP MASS CONCRETE N/A
RLW = 3000 2800 3100 2900 3000 3500 3800 4100 4600
EXISTING
700 x 700 x 800 DEEP MASS CONCRETE
RLW = 3600 2800 3000 2800 3000 3400 3700 4000 4400 OR HOUSE
PC PC PC PC 3m MAXFREESTANDING
BEAM SPAN FOR N/A
RLW = 4200 2700 2900 2700 2900 3300 3200 3800 4200 FASCIA CONNECTION Ø300 x 1200 DEEP MASS CONCRETE PILE
PF PF PF PF
NOTE: SOLAR PANELS TO BE INSTALLED TO MANUFACTURER'S SPECIFICATIONS.
PF

TYPICAL ELEVATION AT TRUSS (TR) - 1:100

PURLIN (PP) MAX SPAN TABLE - 1kN MAX POINT LOAD END ELEVATION EDGE BEAMS (PEB) MAX SPAN TABLE - 1kN MAX POINT LOAD
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE.
76 x 38 x 1.2 76 x 38 x 1.6 76 x 38 x 2.0 90 x 38 x 1.2 90 x 38 x 1.6 75 x 50 x 1.6 75 x 50 x 2.0 100 x 50 x 1.6 100 x 50 x 1.6 100 x 50 x 2.0 100 x 50 x 3.0 150 x 50 x 2.0 150 x 50 x 3.0 150 x 50 x 4.0
PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS
EXISTING FASCIA
MAX PURLIN SPACING = 1200 & GUTTER
2400 2900 3000 2800 3000 3000 3300 4200 3m MAX BEAM3400
PATIO WIDTH MAX = 4000 SPAN FOR 3900 4200 5300 5900 6200
(ADD FASCIA PLATE) FASCIA CONNECTION
MAX PURLIN SPACING = 1800 2300 2800 3000 2700 3000 3000 3300 4000 PATIO WIDTH MAX = 6000 2800 3300 3800 4400 5300 5600
MAX PURLIN SPACING = 2400 2200 2700 2900 2600 2900 2900 3200 3800 PATIO WIDTH
1,000 MAX = 8000
1,000 2500 2900 3600 3900 4900 5200
PP 2600 PP PP PP PP PP PP2900 PP TRUSS
MAX PURLIN SPACING = 3000 NOT ADVICED 2500 2500 2900 2900 3600 MAX MAX
PATIO WIDTH MAX = 10000 2200 2600 3200 3500 4400 5000

3m MAX BEAM SPAN

MAXIMUM PURLIN OVERHANG AT 900 (OR 20% OF THE BACKSPAN - WHICHEVER IS
600 (OR 20% OF THE BACKSPAN - WHICHEVER IS LESS)

END ELEVATION
GABLE END PP LESS)

BEAM
BEAM

BEAM

BEAM

BEAM
EXTENSION OF PURLIN
PP PC & PEB
SETBACK OF
PC ON PEB OR TRUSS EXISTING
GABLE TRUSS (GT) MAX SPAN TABLE
PATIO COLUMN (PC) HOUSE
PP TRUSS MEMBERS SPAN TO RHS SECTIONS REQUIRED
76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT
76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT 4700 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. 400 TOP
PATIO COLUMN & PF PF OR BOTTOM CHORD EXTENSIONS.
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT PATIO FOOTING)
6300 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. NO
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT EXTENSIONS.
TRUSS
76 x 38 x 1.6 PATIO TUBE 6300 (WITH FOR TOP / BOTTOM CHORD EXTENSIONS TO 1000mm,
TYPICAL PLAN - 1:100 END ELEVATION - OPTION POST OR
EXTENSION/POST
100 x 50 x 2.0 RHS DURAGAL
1000 MAX FOR SETBACKUSE 100 x 50 x 2.0 RHS.
EXTENSIONS) OTHERWISE AS PER 8000 SPAN ABOVE.
NOTES:
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS. 8000 TOP CHORD 76 x 38 x 1.6 RHS Gr350 - NO EXTENSIONS.
- STEEL GR350 FOR 76 x 38 x 1.2 / 1.6 MEMBERS, & GR450 DURAGAL FOR OTHERS U.N.O. WEBS 76 x 38 x 1.6 RHS OR 30 x 1.6 SHS. BOTTOM
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. TRUSS CHORD 100 x 50 x 2.0 RHS. NO EXTENSIONS.
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE.

BEAM
PE & CRITERIA PURLIN
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO A
ULAR HOUSE. SETBACK OF
SIGN LOADINGS ARE AS/NZS 1170. PC ON BEAM
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED.
PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS VOIDS THE PP - PATIO PURLIN
PEB - EDGE BEAM
TIFICATION. END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG, PC - PATIO COLUMN
PF - PATIO FOOTING
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 NTS
Scale: Sheet:
S1.1 S3.1Sheet:

ionGSPublisherVersion
0.0.100.100 0.0.100.100
 PATIO COLUMN (PC) COLUMN (PC) BASE FIXINGS
PATIO CONDITIONS (TOPOGRAPHICAL FACTOR OF 1.0)

SKILLION 76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT ROOF AREA FOOTING SIZE (PC CAST IN) FULL
CATEGORY SLAB THICKNESS (PC PARTIAL
FIXING ON TOP) NO
DIMENSIONS FOR ECODECK/SOLARSPAN TYPE ROOF OR TIMBER/GYPROCK
ALTERNATIVE 76 x 38 x 1.6 PATIO TUBE CEILINGS
TO 3600 MAX HEIGHT 8m²
TERRAIN
500 x 500 x 500 DEEP MASS CONCRETE
CATEGORY - 3 75mm MIN UNREINFORCED SLAB
SHIELDING SHIELDING SHIELDING

B PP B PP B
90 x 90 x 2.0 SHS (Gr450) TO 4000 MAX HEIGHT & FREESTANDING 14m²
TERRAIN
600 x 600 x 600 DEEP MASS CONCRETE
TERRAIN CATEGORY - 2.5 100mm MIN REINFORCED SLAB
¸
100 x 50 x 2.0 SHS PATIOS (OR LARGER COLUMN FOR
150 x 50 x 2.0 SHS AESTHETIC REASONS) 20m² 700 x 700 x 700 DEEP MASS CONCRETE
TERRAIN CATEGORY - 2 N/A
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT 700 x 700 x 700 DEEP MASS CONCRETE
WIND REGION A - 1kN MAX POINT LOAD
DOME TRUSS FREESTANDING OR N/A
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT
ALTERNATIVE PP PP PP PP PP PP Ø300 x 1200 DEEP MASS CONCRETE PILE
B B B 150 x 50 x 3.0 SHS (Gr450) WHEN ADDING SOLAR PANELS

TRUSS
PP PP PP PP
GABLE TRUSS PP PP PP PP
CRANKED BEAMS (CB) MAX SPAN TABLE - 1kN MAX POINT LOAD
B B B B
76 x 38 x 1.2 76 x 38 x 1.6 76 x 38 x 2.0 90 x 38 x 1.2 90 x 38 x 1.6 75 x 50 x 1.6 75 x 50 x 2.0 75 x 50 x 3.0 100 x 50 x 1.6 100 x 50 x 2.0 100 x 50 x 3.0 150 x 50 x 2.0 150 x 50 x 3.0
PP
PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS BEAM
RLW = 1800 2900 3500 3700 3200 4100 3700 4000 4600 5100 5500 6200 8100 6600 PURLIN
RLW = 2400 2800 3400 3600 3100 4000 3600 4000 4500 4900 5300 6000 7600 6100
RLW = 3000 2700 3300 3500 3000 3900 3600 3800 4400 4800 5200 5700 7200 5700
EXISTING
RLW = 3600 2600 3200 3400 2900 3700 3500 3700 4300 4600 5000 5500 6900 5500 HOUSE
PC PC PC PC 3m MAX BEAM SPAN FOR
RLW = 4200 2500 3100 3300 2800 3600 3400 3600 4100 4400 4800 5200 6700 FASCIA5300
CONNECTION
PF PF PF PF
NOTE: SOLARSPAN/ECODECK TO BE INSTALLED TO MANUFACTURER'S SPECIFICATIONS.
PF

TYPICAL ELEVATION AT TRUSS (TR) - 1:100

PURLIN (PP) MAX SPAN TABLE - 1kN MAX POINT LOAD END ELEVATION COLUMN (PC) BASE FIXINGS
NOTE: NUMBER OF BAYS, LENGTH & WIDTH TO SUIT PARTICULAR SITE.
76 x 38 x 1.2 76 x 38 x 1.6 76 x 38 x 2.0 90 x 38 x 1.2 90 x 38 x 1.6 75 x 50 x 1.6 75 x 50 x 2.0 100 x 50 x 1.6 150 x 50 x 3.0 ROOF AREA FOOTING SIZE (PC CAST IN) SLAB THICKNESS (PC FIXING ON TOP)
PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE PATIO TUBE DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS
EXISTING FASCIA
MAX PURLIN SPACING = 1200 & GUTTER
2800 3300 3600 3300 4000 3600 3300 4000 7100 SPAN FOR 500 x 500 x 500 DEEP MASS CONCRETE
6.4m²
3m MAX BEAM 75mm MIN UNREINFORCED SLAB
(ADD FASCIA PLATE) FASCIA CONNECTION
11m² 600 x 600 x 600 DEEP MASS CONCRETE 100mm MIN REINFORCED SLAB
MAX PURLIN SPACING = 1800 2700 3300 3500 3200 3900 3500 3200 3900 6600
16m² 700 x 700 x 700 DEEP MASS CONCRETE N/A
MAX PURLIN SPACING = 2400 2600 3200 3400 3100 3700 3400 3100 3800 6100 1,000 1,000
PP 3100 PP PP PP PP PP PP3600 PP TRUSS
700 x 700 x 800 DEEP MASS CONCRETE
MAX PURLIN SPACING = 3000 2500 3300 3000 3300 3000 3700 5700 MAX MAX
FREESTANDING OR N/A
Ø300 x 1200 DEEP MASS CONCRETE PILE

3m MAX BEAM SPAN

MAXIMUM PURLIN OVERHANG AT
600 (OR 20% OF THE BACKSPAN - WHICHEVER IS LESS) 900 (OR 20% OF THE BACKSPAN - WHICHEVER IS LESS)

END ELEVATION
GABLE END PP

BEAM
BEAM

BEAM

BEAM

BEAM
EXTENSION OF PURLIN
PP PC & PEB
SETBACK OF
PC ON PEB OR TRUSS
EDGE BEAMS (PEB) MAX SPAN TABLE - 1kN MAX POINT LOAD EXISTING
GABLE TRUSS (GT) MAX SPAN TABLE
PATIO COLUMN (PC) HOUSE
PP 100 x 50 x 1.6 100 x 50 x 2.0 100 x 50 x 3.0 150 x 50 x 2.0 150 x 50 x 3.0 150 x 50 x 4.0 TRUSS MEMBERS SPAN TO RHS SECTIONS REQUIRED
76 x 38 x 1.2 PATIO TUBE TO 3000 MAX HEIGHT
DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS DURAGAL RHS
76 x 38 x 1.6 PATIO TUBE TO 3600 MAX HEIGHT 4700 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. 400 TOP
PATIO WIDTH MAX = 4000 4300 PATIO
4900COLUMN & 5300 6700 7400 PF 7700 PF OR BOTTOM CHORD EXTENSIONS.
90 x 90 x 2.0 SHS (G350) TO 4500 MAX HEIGHT PATIO FOOTING)
PATIO WIDTH MAX = 6000 3600 4100 4800 5600 6700 7000 6300 ALL 76 x 38 x 1.6 RHS Gr350 OR 30 x 1.6 WEBS. NO
100 x 100 x 3.0 SHS (G350) TO 6000 MAX HEIGHT EXTENSIONS.
PATIO WIDTH MAX = 8000 3100 TRUSS 3600 4400 4800 6200 6500
76 x 38 x 1.6 PATIO TUBE 6300 (WITH FOR TOP / BOTTOM CHORD EXTENSIONS TO 1000mm,
PATIO WIDTH MAX = 10000 2800 3200 4000 4400 5600 6200
TYPICAL PLAN - 1:100 END ELEVATION - OPTION POST OR
EXTENSION/POST
100 x 50 x 2.0 RHS DURAGAL
1000 MAX FOR SETBACKUSE 100 x 50 x 2.0 RHS.
EXTENSIONS) OTHERWISE AS PER 8000 SPAN ABOVE.
NOTES:
- BASES, CONNECTION DETAILS & DETAILS NOT SHOWN TO BE AS PER SEPARATE GABLE, DOME AND FLAT PATIO DRAWING SETS. 8000 TOP CHORD 76 x 38 x 1.6 RHS Gr350 - NO EXTENSIONS.
- STEEL GR350 FOR 76 x 38 x 1.2 / 1.6 MEMBERS, & GR450 DURAGAL FOR OTHERS U.N.O. WEBS 76 x 38 x 1.6 RHS OR 30 x 1.6 SHS. BOTTOM
- MIN ROOF SLOPE TO MANUFACTURER'S SPECIFICATIONS. TRUSS CHORD 100 x 50 x 2.0 RHS. NO EXTENSIONS.
- OPTION WITH EXTENSION AND SETBACK OF PC ON PEB AND TRUSS CAN BE AT FRONT, REAR OR SIDE.

BEAM
PE & CRITERIA PURLIN
S DESIGN APPLIES TO A REGULAR PATIO ATTACHED TO A
ULAR HOUSE. SETBACK OF
SIGN LOADINGS ARE AS/NZS 1170. PC ON BEAM
ORK TO COMPLY WITH BCA, RELEVANT AUSTRALIAN
NDARDS & STATUTORY REQUIREMENTS, OUTSIDE THIS
PE INDIVIDUAL ENGINEERING DESIGN IS REQUIRED.
PP - PATIO PURLIN
ARTURE FROM THESE SPECIFICATIONS VOIDS THE PP - PATIO PURLIN
PEB - EDGE BEAM
TIFICATION. END ELEVATION - OPTION POST SETBACK AND FIXED ON BEAM PF - PATIO
PCFOOTING
- PATIO COLUMN
EXISTING HOUSE HAS TRUSS ROOF & EAVES OVERHANG, PC - PATIO COLUMN
PF - PATIO FOOTING
ENGTHEN OVERHANG TO ACCEPT LOADS FROM PATIO AS TR - TRUSS
GT - GABLE TRUSS
UIRED BY TRUSS MANUFACTURER. B - BEAM CB - CRANKED BEAM
Approved by:

COPYRIGHT
COPYRIGHT
Address: Address:
STEEL STEEL
PATIO OR CARPORT
PATIO (COMBINATION)
OR CARPORT (GABLE ROOF)
Approved by:

G A Gaynor MIEAust, CPEng, NER

Chartered Professional Engineer
This drawing
Thisis drawing
copyright. No part ofNo
is copyright. thispart
drawing
of thismay be reproduced
drawing may be reproduced Membership No. 3303920

without thewithout
permission of Engineer
the permission of Perth
EngineerPty Perth
Ltd. Contractor shall
Pty Ltd. Contractor shall 12 (15/07/20)
Revision:
11 (01.07.19)
Revision:
verify jobverify
dimensions before any
job dimensions workany
before commences. Figured Figured
work commences.
E N G IENNEGEI RN EP EE RR TPHE R T H dimensionsdimensions
shall take shall
precedence over scaled
take precedence work.
over Work
scaled shallWork
work. also shall also Date: 15/07/20
conform toconform
the specification and other and
to the specification drawings. This drawing
other drawings. Thiscannot
drawing cannot On behalf of Engineer Perth
Expire date:
26/443 Albany26/443
Highway, Victoria
Albany Park, Victoria
Highway, WA 6100 Park, WA 6100 be submitted as part of aasBuilding
be submitted part of aPermit Application
Building without a blue
Permit Application ink a blue ink
without Issue date:
p: 08 6424 8129 e:6424
p: 08 [email protected]
8129 e: [email protected]
w: www.engineerperth.com.au
w: www.engineerperth.com.au
signature from an authorised
signature Engineer Perth
from an authorised signatory.
Engineer Perth signatory. 16-02-2021 Scale:
1:100 NTS
Scale: Sheet:
S1.1 Sheet:
S3.2
ionGSPublisherVersion
0.0.100.100 0.0.100.100