OPERATING
MANUAL

TEMPERATURE
&
HUMIDITY
CONTROLLER

MHT-1202

Technical
Specification
1.Micro
Controller
Based,
Double
Display
2.Upper
display,
7
seg,
red
0.56”
LED
for
process
value
sensor
1.




Lower
display,
7
seg,
green
0.56”
LED
for
process
value
sensor
2.

3.Dimension
:

Size
:
96(H)
X
96(W)
X
50(D)
mm.




Panel
Cutout
:

92
X
92
mm.
4.Input
:

PT-100/3W
&
Humidity
sensor
(RH-100SL)

5.Range
:

PT-100
(0.0
To
400.0°C)
Humidity

(0.0
TO
100.0
%
RH)
6.
Supply
:
100
To
250V
AC,
50/60
Hz,
Approx
4VA
7.
Output
:
2Relay
1C/O
(On-Off)
8.
Protection
Level
:
IP-65
(Front
side)
As
per
IS/IEC
60529
:
2001

NOTE:
1.
Make
all
connection
properly
according
to
ʻCONNECTION
DIAGRAMʼ
given
below.




Then
turn
ON
instrument.
Set
all
parameters
according
to
your
requirement.




Then
press
ENTER
key
to
store
new
value
in
memory.
2.
Display-1
(upper)
indicates
temperature
value
for
Pt-100
and
Display-2
(lower)




indicates
temperature
value
for
Humidity.


Accurate Sensing of humidity is subject to proper mounting of humidity sensor




as per application area. Please consult our support engineers if needed.

Connection
Diagram
20 19 18 17 16 15 14 13 12 11
Y R B
I/P +5V DC GND
www.multispanindia.com
(RH-100SL) PT-100/3W

Range: 0.0 To 400.0°C

Made in India 0.0 To 100.0% RH
100 ~ Input: PT-100/3W
Humidity Sensor (RH-100SL)
250V AC
50/60 Hz Output: 2R1C/O (ON-OFF)
4VA
RELAY-1 RELAY-2
NO C NC NO C NC
L N
1 2 3 4 5 6 7 8 9 10

MHT-1202 Page
-
1 www.multispanindia.com

 USER
CONFIGURATION
Menu-1 Power
ON
Press







key
SET

Set
1 s E T 1 For
PT-100
0 5 0. 0 (0
To
400.0)
Press







key
SET

Hysteresis
1 H Y S 1 For
PT-100
0 0 0. 5 (0.1
To
99.0)
Press







key
SET

Time
1 T I M 1 For
PT-100 (If
RMod1=COOL)

0 0 0. 5 (0.0
To
99.9Min)
Press







key
SET

Set
2 s E T 2 For
Humidity
1 0 0. 0 (
0
To
85.0)
Press







key
SET

Hysteresis
2 H Y S 2 For
Humidity
0 0 0. 5 (0.1
To
99.0)
Press







key
SET

Time
2 T I M 2 For
Humidity (If
RMod2=H-AL)

0 0 0. 5 (0.0
To
99.9Min)
Press







key
SET

Pass
Word
P A S S For
Password
0 1 2 3 (0123)
Press







key
SET

Set
Low
Limit
S L L For
PT-100
0 0 0. 0 (0000)
Press







key
SET

Set
High
Limit
S H L For
PT-100
4 0 0. 0 (0
To
400.0)
Press







key
SET

Mode
1
M O D 1 For
PT-100
H E A T Heat/Cool
Press







key
SET

M O D 2 For
Humidity
L - A L (L-AL/H-AL)
Press







key
SET

Press




key
to
save
&
exit
ENT

Menu-2
Press





+





key

Off
set
1 O F S 1 For
PT-100
Press






key

0 0 0 0 Range:
±20.0°C
Press







key
SET

SET

Off
set
2 O F S 2 For
Humidity
0 0 0 0 Range:
±20.0%
RH

Press




key
to
save
&
exit
ENT

Product
improvement
and
upgrade
is
a
constant
procedure.
So
for
more
updated
operating
information
and
support,

please
contact
our
helpline
:
+91-9978991474/
76
/82
or
Email
at
[email protected]



























Ver:1902
MHT-1202 Page
-
2 www.multispanindia.com