S300Xd1 R450Xd1 U500Xd1

S500Xd1 R650Xd1
S700Xd1 M200Xd1 H550Xd1
W1000Xd2 M300Xd1

General Catalog
 Cutting Out Times are changing. Are you ready?
You need a machine that’s fast and compact.
With the ability to make any cut.

the Waste In this world, only the strong survive.

Make it better with SPEEDIO.

Extensive lineup further expands the potential of #30 spindle machines, and
provides customers with the best waste-free solution

S300Xd1 S500Xd1 S700Xd1 W1000Xd2 U500Xd1

Compact Machining
Wide Travel Universal
Center
Compact Machining Compact Machining
Center Center

R450Xd1 R650Xd1 H550Xd1

Pallet Changing
Compact Machining
Center
High Rigidity
Compact Machining
Center
H
Horizontal
Compact Machining Center

Rotary Table Loading System

M200Xd1 M300Xd1 T-200Ad / T-200A BV7-870Ad

Special Options

Compact Multi-Tasking
Machine
 Pursuit of high productivity Pursuit of environmental performance

High-speed operations and optimized control have been achieved by the #30 spindle Reduction in power and air consumption results in a great decrease in CO2 emissions,
taper and original NC, enabling the machine to demonstrate high productivity. making the machine more earth-friendly and providing high environmental performance.

Non-stop ATC Highly responsive servomotor Simultaneous operation Low power consumption Low air consumption
Fastest tool change among #30 spindle machines has World's fastest highly accurate tapping has been Using the original non-stop ATC code (G100) allows the Equipped with a power regeneration system that reuses energy generated when Chip removal performance has been enhanced by optimizing the air purge path and
been achieved by quick start/stop of the spindle, high achieved, using our original synchronized tapping control machine to simultaneously position the X/Y- and decelerating, high-efficiency motor, energy saving pump, LED work light and other spindle air blow timing, greatly reducing air consumption.
acceleration and quick response when the Z-axis moves and a fast acceleration/deceleration spindle motor. additional axes while performing a tool change, leading energy saving functions, achieving low power consumption.
up and down, and optimized magazine operation. to further reduction of wasted time.
Power consumption for one cycle Air consumption for one cycle

Power consumption (kWh/cycle)

Air consumption (L/min)

Approx. 80% Approx. 80%
less less

General M/C SPEEDIO General M/C SPEEDIO

*Data taken running machining program created by Brother *Data taken running machining program created by Brother

Pursuit of machining capabilities Pursuit of Usability

The highly rigid structure and high-power spindle motor allow the machine to demonstrate Optimizing usability for manufacturing by eliminating any waste improves
its broad machining capabilities, from high-efficiency machining to heavy-duty machining. work efficiency and operating rate at production sites.

Highly rigid structure High-power spindle motor New “CNC-D00” controller

Intuitive operation is possible with 15-inch vertical touch panel screen and new support apps.
Based on accumulated data using analysis technologies, a highly High-speed, high-efficiency machining has been achieved using a spindle motor with high torque in the
Relevant functions are grouped according to purpose, such as setup and machining settings, leading to efficient operation.
rigid structure with vibration suppressed has been achieved, allowing medium- and high-speed range. High-torque specifications (optional) greatly improve low-speed range
Production and operation states are visualized, allowing faster understanding.
the machine to demonstrate excellent machining capabilities. torque, providing excellent heavy-duty machining for steel workpieces.
Any wasted operation is eliminated in each process.
Medium- and high-speed range Low-speed range suitable for
enabling high-efficiency machining heavy-duty machining Setup support Machining adjustment Support
Equipped with functions to easily perform Equipped with functions to easily perform optimal
setup, such as an ATC tool app that enables all machining adjustment to improve productivity,
magazine tool settings to be performed on one such as a machining parameter adjustment app
screen, menu programming that enables you that enables you to easily adjust parameters
to create NC programs by following instructions according to machining details and a machining
on the screen, and an on-screen help function. load waveform display/saving function.

Production support Recovery support

Equipped with functions to improve the operating Equipped with functions to prevent failure or iF DESIGN AWARD is hosted and
judged by the iF International Forum
rate, such as real time tool monitoring to eliminate ensure quick recovery, such as maintenance Design GmbH, in Germany. This is
Grooving using standard specs Large hole drilling using high-torque specs defects, displaying production performance, time notice, displaying details when an alarm one of the most prestigious
international design competitions
Machining Cutting amount: 150 cc/min Machining Hole diameter: D40 mm power consumption etc. as a graph, and occurs, and guidance for recovery/check
and has been running since 1953.
details Material: Carbon steel details Material: Carbon steel PLC/network functions to meet peripheral work.
(D16 end mill used) CNC-D00 controller equipment and automation requirements.

3 4
 SPEEDIO Compact Machining Center SPEEDIO Wide Travel Compact Machining Center

High performance model suitable for a broad range of machining applications Wide travel model with the largest machining area among BT30 spindle machines

Extensive spindle specifications and machine sizes Unprecedented large machining area enables
Further pursuing high productivity highly productive machining
and high reliability from small to large parts

2
2023 2023
S300Xd1 S500Xd1 S700Xd1

Pursuit of high productivity A variety of machining from small to large workpieces

Optimizing control with the new “CNC-D00” controller eliminates all possible wasted operation during machining. Drives highly reliable machine performance to the limit to Machine's abilities to handle large workpieces and multi-type small-volume products Increased Z-axis travel Machining of large workpieces
provide high productivity. have been further enhanced by the largest travels of any BT30 machines at X1,000 mm
and Y500 mm, maximum loading capacity of 500 kg, and increased Z-axis travel.
+50mm
Non-stop ATC and 28-tool magazine Simultaneous operation
In addition to 14- and 21-tool magazines, a 28-tool Ample travels and table size
magazine has been developed with high-speed tool 300mm
Travels Increased
change performance maintained. The maximum tool
X1,000 Y500
Z-axis travel 380 mm
weight has been increased to 4 kg.
Work area size
Tool change time of 14- and 21-tool magazines has
X1,100 Y500 +30mm Multi-part machining of small workpieces
been further reduced by optimized magazine Y 500mm Spindle lowest point
Max. loading capacity 150mm
operation, etc. X 1,000mm
500 kg

28-tool magazine 14/21-tool magazine Z-axis travel

Chip-Chip : 1.3s Chip-Chip : 1.2s Width 1,100mm

Depth
500mm 300mm 380 mm
Tool-Tool : 0.7s Tool-Tool : 0.6s Z-axis acceleration : 2.2G A broad range of machining
The machine can perform a broader range of machining with the newly developed 28-tool magazine (optional), newly developed 12,000 min-1 standard spindle motor, and
improved spindle rigidity for high-torque specifications.
High machining capabilities and high reliability
28-tool magazine High-power spindle motor Improved spindle rigidity
Highly rigid machine structure and highly efficient spindle motor enable a board range of machining. Prevention of chip problems
Roof-shape telescopic covers Motor torque characteristics
Standard spec. Max. torque
(instantaneous) 40N∙m are used for the X/Y-axes to help

Max. output 18.9kW chips flow smoothly. The shape

for the chip flow path from the
92Nm
High-torque spec.
machining room to the tank was
92N∙m

Torque (Nm)
High-torque spec. Max. torque devised to increase the flow speed.
(instantaneous)
(Optional)
Max. output 26.2kW Changing the shape under the
Y-axis telescopic cover and
40Nm

increasing the flow rate have Standard spec.

improved chip evacuation
performance by almost two-fold.
Spindle speed (min-1) 10,000 12,000
Spindle bearing diameter
(High-torque spec.) Larger by 10%
5 6
 SPEEDIO Compact Multi-Tasking Machine SPEEDIO Pallet Changing Compact Machining Center

Mass production type multi-tasking machine encourages process integration Non-stop machining model equipped with a pallet changer

Newly developed magazine and new controller Extensive magazine variation

further encourage process integration further promotes process
integration

M200Xd1 M300Xd1 R450Xd1 R650Xd1

2023 2023

Awarded to M200Xd1

Complex machining Machine structure Non-stop machining

Turning and milling can be completed through one-time chucking A roller gear cam is used for the tilt axis (A-axis), a DD motor for the turning spindle (C-axis), and an The QT (Quick Turn) table is a turntable type high-speed 2-face pallet changer. Optimized
on one machine. There is no handling between turning and original double plunger lock to secure turning tools. acceleration/deceleration control achieves much faster pallet change. To ensure high reliability,
milling, leading to various advantages. effects by chips etc. are minimized by a turntable that avoids lift-up motion and has a sealed
Turning spindle (C-axis) Double plunger lock structure, and positioning accuracy is maintained by the stopper mechanism. Workpieces on one
pallet can be changed while machining workpieces on the other pallet. Waste in workpiece change
Lathe time is eliminated, enabling non-stop machining.
+
Machining
center
Pallet 1

Pallet 2

Machining Workpiece Pallet change

change time time
M300Xd1 time
Pallet change time
R450Xd1 2.7s
A high-speed and high-power built-in DD motor An original double plunger lock is used to secure
is used for the turning spindle (C-axis). Enabling turning tools, achieving excellent tool change R650Xd1 3.1s
efficient turning and high-speed indexing. repeatability.

Large jig area Extensive magazine variation *2

28-tool magazine Simultaneous 5-axis machining * 1
A-axis clamp Even if the jig protrudes from the table, it can be mounted as long as it is within the pallet turning (14/22/28/40-tool magazines)
In addition to a 22-tool magazine, a newly developed Provided with functions required for simultaneous 5-axis machining, The mechanical clamp plus servo clamp method enables diameter. The jig area can be further expanded by selecting a low table option that increases the In addition to 14-, 22-, and 40-tool magazines, a newly developed 28-tool
28-tool magazine is available. High-speed tool change including tool center point control where machining is performed the machine to demonstrate high machining capabilities in jig height or a turning diameter enlargement option that increases the jig space. magazine is available. This promotes process integration, taking advantage
has been achieved by faster and optimized spindle by changing the tool direction relative to the workpiece, look-ahead high-load machining and stable lathe turning, improving of a 2-face pallet changer, and encourages productivity improvement.
start/stop, Z-axis up/down, and magazine operation. max. 1,000 blocks, and submicron command. machining accuracy. A double type clamp mechanism,
where clamps are provided on the left and right sides, is
available to further enhance high machining capabilities.
R450Xd1
A-axis clamp torque Max. jig height *1
380mm

Single 695 N∙m R450Xd1 380mm

Double 975 N∙m R650Xd1 450mm 40-tool magazines
Artificial bone *1 The values shown here are for low *2 The 40-tool magazine is only available for the R650Xd1.
table specifications.
*1 Available only for the M200Xd1-5AX/M300Xd1-5AX.
7 8
 SPEEDIO Universal Compact Machining Center SPEEDIO High Rigidity Compact Machining Center

U
Equipped with a newly developed tilting rotary table with a maximum jig area of 500 mm in diameter Machining capabilities improved by highly rigid structure and minimizing vibration

Performs universal indexing, Reduction in cutting time and

encouraging process integration non-cutting time greatly
improves production efficiency

2023
U500Xd1

Process integration for multi-face machining Highly rigid structure and stable machining
Less space achieved although the machine is equipped with a high-speed and highly accurate The machine structure has been newly designed from the base up using structural analysis techniques. The rigidity of the drive system and spindle has been enhanced by
tilting rotary table with ample jig area and a newly developed 28-tool magazine. One-clamp using table movement for the Y-axis and column movement for the X- and Z-axes. In addition, the structure has been totally reviewed through vibration analysis to minimize
machining encourages process integration. vibration during machining, achieving stable machining in a broad range of spindle speeds.

Highly rigid machine structure Wide stable range High-power spindle motor
Tilting rotary table

Large
Vibration image Standard equipped with the highest class high-torque motor
Roller gear cam mechanism is used for A and C axes, achieving high retention strength and
among spindle motors used for #30 spindle machines.
backlash-free high-speed and highly accurate indexing. Column

Vibration
Other
Max. rotary speed model Spindle motor characteristics

A-axis 50min-1 C-axis 75min-1 F600X1 Max. torque

(instantaneous) 92N∙m
26.2kW

Small
Max. output
0 to 90-deg. indexing time Table
Low Spindle speed High

A-axis 0.9s C-axis 1.2s

Ample machining area Improved chip evacuation

Jig area 28-tool magazine Simultaneous 5-axis machining *1
Ample machining area and large table size to accommodate Chip evacuation performance has been improved along with the expansion of the machining area. In
Provides ample jig area of ø500 x H270 to meet A newly developed compact drum type 28-tool Provided with functions required for simultaneous 5-axis machining, large workpieces. The maximum table loading capacity has addition, a coil conveyor and a cyclone filter are available.
multi-face machining for medium-sized workpieces. magazine takes over fast tool change performance. including tool center point control where machining is performed been increased to 500 kg by thickening the table.
(14- and 21-tool magazines are also available.) by changing the tool direction relative to the workpiece, look-ahead
max. 1,000 blocks, and submicron command. Travels Coolant flow path Coil conveyor (optional)

ø500
Y 400mm
X 600mm
H270 Z 350mm

Table size

Depth
*1 Available only for the U500Xd1-5AX. Width 800mm 400mm

9 10
 SPEEDIO Horizontal Compact Machining Center SPEEDIO Special Options

H
Ample jig area and a newly developed magazine enable multi-face machining of large or long workpieces.
Further enhancing productivity
New style of SPEEDIO in multi-face machining
Horizontal Compact Machining Center Special option for SPEEDIO

now available Rotary Table

T-200Ad / T-200A
Using roller gear cam mechanism

Output Cam
shaft follower

Preload Preload

Input shaft

High productivity High accuracy Maintenance free

Provides high acceleration and high rotation speed to ensure smooth Achieves backlash-free operation by applying There is very little wear as the input and output
operation even for jigs with large unbalanced load. preload between the input and output shafts. shafts make rolling contact. Adjustment is not
H550Xd1 necessary for long periods.
Main specifications
Type Right-handed, Left-handed *1 Gear ratio 1/20 Maximum loading capacity 100/220 (200/440 *3) kg
Center height 170mm Maximum speed 100 (50 *2) min-1 Product weight 61kg
B-axis table (standard) and ample jig area Space saving Applicable models T-200Ad (for CNC-D00) S300Xd1/S500Xd1/S700Xd1/W1000Xd1/W1000Xd2/R450Xd1/R650Xd1
*4,*5 T-200A (for CNC-C00) F600X1/S500Z2N/S700Z2N/R450Z1
The B-axis table with a roller gear cam mechanism is provided standard, achieving Machine dimensions are 1,557 mm in width and 2,990 mm in depth, achieving
*1. Only right-handed type available for R450Xd1 and R650Xd1. *2. When high inertia mode (enabled by changing parameter setting) is used. *3. When support table is used. *4. S500Z2N, S700Z2N, and
an ample jig area of ø600 x 580 mm. *1 reduction in space while maintaining ample jig and machining areas. R450Z1 sold only in China. *5. T-200A can also be used for S300X2/X1, S500X2/X1, S700X2/X1, R450X2/X1, and R650X2/X1.
The jig area can be expanded to ø800 mm by moving the tool to a safe position,
etc. *2 Installation space
φ600mm 4.7m2 * 3

Space required for

typical BT40 horizontal MC *4
Simple & Compact
J2
Manpower saving system with easy introduction and setup
580mm
Approx 20% less *4
*1. Interference area is created Special option for SPEEDIO J1 J3
depending on the tool length or
tool diameter.
*2. The tool must be moved to a
*3. Dimension including
coolant tank
Loading System
safe position when the B-axis Depth *4. Compared to BT40
rotates or the tool length must be
restricted. Width 1557mm 2990mm *3 horizontal MC with
equivalent travels

30-tool magazine Chip evacuation performance

Equipped with the newly developed direct ATC type 30-tool magazine. Supports Designed to prevent problems caused by chips by enhancing chip evacuation performance
maximum tool length of 250 mm, maximum tool diameter of 125 mm, and maximum with a magazine cover that separates the magazine from the machining area, a center
tool weight of 4 kg, enabling a variety of machining, including long workpieces. trough structure, and a head shower (optional) that removes chips from the spindle head.
TR

Center trough structure Head shower

BV7-870Ad

Integrated with the SPEEDIO Specialized for loading/unloading workpieces Controller incorporated in SPEEDIO's control box

Standard equipped with a side door, and can be Simple structure with easy handling 4-axis articulated arm Signal connection with machine’s NC completed. Both
installed in less space piping and wiring stored in the body.

Main specifications
No. of axes 4 (3 rotary axes, 1 travel axis) Arm length Total 870 mm Applicable models S300Xd1/S500Xd1/M200Xd1
Loading position Right side / Left side Rated transferable weight 7kg

11 12
 SPEEDIO Machine Specifications SPEEDIO Machine Specifications

Machine specifications Machine specifications

S300Xd1 S500Xd1 S700Xd1
S300Xd1 RD *9 S500Xd1 RD *9 S700Xd1 RD *9 R650Xd1/R650Xd1 RD *12
Item S300Xd1-5AX S500Xd1-5AX S700Xd1-5AX W1000Xd2/W1000Xd2 RD *9 Item R450Xd1/R450Xd1 RD *12
S300Xd1-5AX RD*9 S500Xd1-5AX RD *9 S700Xd1-5AX RD *9 14/22/28 tool magazine 40-tool magazine
《S300/S500/S700Xd1》 CNC-D00 CNC Unit CNC-D00 CNC-D00
CNC unit CNC-D00
《S300/S500/S700Xd1-5AX》 CNC-D00v（DB） X axis mm(inch) 450 (17.7) 650 (25.6)
X axis mm(inch) 300 (11.8) 500 (19.7) 700 (27.6) 1,000 (39.4) Y axis mm(inch) 320 (12.6) *7 400 (15.7)
Travels
Y axis mm(inch) 400 (15.7) 500 (19.7) Z axis mm(inch) 305 (12.0) 305 (12.0) 435 (17.1)
Travels Distance between table top mm(inch)
Z axis mm(inch) 300 (11.8) 380 (15.0) and spindle nose end 200~505 (7.9~19.9)[280~585 (11.0~23.0) *8] 250~555 (9.8~21.8) [350~655 (13.8~25.8) *8] 250~685 (9.8~27.0) [350~785 (13.8~30.9) *8]
Distance between table top
and spindle nose end mm(inch) 180~480 (7.1~18.9) 150~530 (5.9~20.9) Work area size mm(inch) One face 600 x 300 (23.6 x 11.8) One face 800 x 400 (31.5 x 15.7)
Work area size mm(inch) 600 × 400 (23.4 × 15.7) 800 × 400 (31.4 × 15.7) 1,100 × 500 (43.3 × 19.7) Table Max.loading capacity(uniform load) kg(lbs) One face 120（265) [200(441) *6] One face 200 (441) [300 (661) *6]
Table
Max. loading capacity (uniform load) kg(lbs) 250[300 *6] (551[661 *6]) 250[400 *6] (551[881 *6]) 300 [500 *6] (661 [1,102 *6]) Position time sec. 2.7 *11 3.1 *11 3.1 *11
12,000min-1 specifications: 1~12,000, 10,000min-1 specifications: 1~10,000 10,000min-1 specifications: 1~10,000
10,000min specifications: 1~10,000, 16,000min specifications (optional): 1~16,000
-1 -1

Spindle speed min-1 10,000min-1

high-torque specifications (optional): 1~10,000, Spindle speed min-1 16,000min-1 specifications(optional): 1~16,000 16,000min-1 specifications(optional): 1~16,000
10,000min-1 high-torque specifications (optional): 1~10,000, 27,000min-1 specifications (optional): 1~27,000 10,000min-1 high-torque specifications(optional): 1~10,000 10,000min-1 high-torque specifications(optional): 1~10,000
16,000min-1 specifications (optional): 1~16,000
Spindle Speed during tapping min-1 MAX. 6,000 (27,000min-1 specifications: MAX. 8,000 MAX. 6,000 Spindle Speed during tapping min-1 MAX. 6,000 MAX. 6,000
Tapered hole 7/24 tapered NO.30 7/24 tapered NO.30 Tapered hole 7/24 tapered No.30 7/24 tapered No.30
BT dual contact spindle (BIG-PLUS) Optional Optional BT dual contact system(BIG-PLUS) Optional Optional
Coolant through spindle (CTS) Optional (CTS cannot be selected for 27,000min-1 specification models) Optional Coolant Through Spindle(CTS) Optional Optional
Rapid traverse rate (XYZ-area) m/min(inch/min) 50 × 50 × 56 (1,969 × 1,969 × 2,205) 50 × 50 × 56（ 1,969 × 1,969 × 2,205） Rapid traverse rate(XYZ-area) m/min(inch/min) 50 x 50 x 50 (1,969 x 1,969 x 1,969) 50 x 50 x 50 (1,969 x 1,969 x 1,969)
Feed rate Feed rate
Cutting feed rate mm/min(inch/min) X,Y,Z: 1~30,000 (0.04~1,181)*7 X,Y,Z:1~30,000（0.04 ~ 1,181）*7 Cutting feed rate mm/min(inch/min) X, Y, Z axis : 1~30,000 (0.04~1,181) *9 X, Y, Z axis: 1~30,000 (0.04~1,181) *9
Tool shank type MAS-BT30 MAS-BT30 Tool shank type MAS-BT30 MAS-BT30
Pull stud type *4 MAS-P30T-2 MAS-P30T-2 Pull stud type *4 MAS-P30T-2 MAS-P30T-2
Tool storage capacity pcs. 14 / 21 14 / 21 / 28 14 / 21 / 28 Tool storage capacity pcs. 14 / 22 / 28 14 / 22 / 28 40
ATC unit Max. tool length mm(inch) 160 (6.3) [21 tool] 250 (9.8) [14 tool] 250 (9.8) 250 (9.8) ATC unit Max. tool length mm(inch) 200 (7.9) 200 (7.9) 250 (9.8)
Max. tool diameter mm(inch) 110 (4.3) 110 (4.3) Max. tool diameter mm(inch) 80 (3.1) 80 (3.1) 55 (2.1) / 125 (4.9) No adjacent tool
3.0 (6.6) [4.0(8.8) *10] / tool, (TOTAL TOOL WEIGHT: Max. tool weight *1 kg(lbs) 3.0 (6.6)〈total tool weight : 25 (55.1) for 14-tool, 40 (88.2) for 22/28 tool> 3.0 (6.6) <total tool weight: 25 (55.1) for 14-tool, 40 (88.2) for 22/28 tool> 4.0 (8.8) <total tool weight: 80 (176.3) >
Max. tool weight *1 kg(lbs) 3.0 (6.6) [4.0 (8.8)*10]/tool, (TOTAL TOOL WEIGHT: 25 (55.1) for 14 tools, 35 (77.2) for 21or 28 tools)
25 (55.1) for 14 tools, 35 (77.2) for 21 or 28 tools) Tool selection method Random short cut method Random short cut method Double arm method (random closet path)
Tool selection method Random shortcut method Random shortcut method Tool *5 Tool To Tool sec. 0.6 / 0.7 (14-tool / 22 or 28 tool) 0.6 / 0.8 (14-tool / 22 or 28 tool) 0.9
Tool *5 Tool To Tool sec 0.6 / 0.7 (14 or 21 tools / 28 tools) 0.6 / 0.7 (14 or 21 tools / 28 tools) change time Chip To Chip sec. 1.3 / 1.5 (14-tool / 22 or 28 tool) 1.4 / 1.5 (14-tool / 22 or 28 tool) 2.5
change time Chip To Chip sec 1.2 / 1.3 (14 or 21 tools / 28 tools) 1.3 / 1.4 (14 or 21 tools / 28 tools) 10,000min-1 specifications: 10.1 / 7.0 10,000min-1 specifications: 10.1 / 7.0
Main spindle motor kW 16,000min-1 specifications: 7.4 / 5.1 16,000min-1 specifications: 7.4 / 5.1
12,000min-1 specifications: 10.1/7.0, Electric
Electric Main spindle motor 10,000min-1 specifications: 10.1/7.0, 16,000min-1 specifications (optional): 7.4/5.1 (10min/continuous) *2 10,000min-1 high-torque specifications: 12.8 / 9.2 10,000min-1 high-torque specifications: 12.8 / 9.2
kW 10,000min-1
high-torque specifications (optional): 12.8/9.2, motor
motor (10min/continuous) *2 10,000min-1 high-torque specifications (optional): 12.8/9.2, 27,000min-1 specifications (optional): 8.9/6.3
16,000min-1 specifications (optional): 7.4/5.1 Axis feed motor kW X, Y axis: 1.0 Z axis: 1.8 X, Y axis: 1.0 Z axis: 1.8
Axis feed motor kW X,Y axis: 1.0 Z axis: 2.0 X,Y axis: 1.0 Z axis: 2.0 Power supply AC 200 to 230 V±10％,3-phase, 50/60Hz±2% AC 200 to 230 V±10％,3-phase, 50/60Hz±2%
Power supply AC 200 to 230 V±10％,3-phase, 50/60Hz±2% AC 200 to 230 V±10%, 3-phase, 50/60Hz±2% 10,000min-1 specifications: 9.5 10,000min-1 specifications: 9.5
Power capacity
12, 000min-1 specifications: 9.5, Power kVA 16,000min-1 specifications: 9.5 16,000min-1 specifications: 9.5
Power capacity 10,000min specifications: 9.5, 16,000min specifications (optional): 9.5
-1 -1 (continuous)
kVA 10,000min-1 high-torque specifications (optional): 10.4, source 10,000min-1 high-torque specifications: 10.4 10,000min-1 high-torque specifications: 10.4
Power (continuous) 10,000min-1high-torque specifications (optional): 10.4, 27,000min-1 specifications (optional): 9.5
source 16,000min-1 specifications (optional): 9.5 Regular air pressure MPa 0.4~0.6 (recommended value : 0.5MPa *10) 0.4~0.6 (recommended value: 0.5MPa *10)
Air
Air Regular air pressure MPa 0.4~0.6 (recommended value 0.5MPa *8) 0.4~0.6 (recommended value 0.5MPa*8) supply Required flow L/min 45 45 100
supply Required flow L/min 45 (27,000min-1 specifications: 115) 45 Height mm(inch) 2,584 (101.7) 2,704 (106.5)
Height mm(inch) 2,498 (98.4) 2,633 (103.7) Machine Required floor space *13 mm(inch) 1,400 x 2,609 [3,448] (55.1 x 102.7 [135.7] ) 1,830 x 3,029 [3,868] (72.0 x 119.3 [152.3] ) 2,145 x 3,029 [3,868] (84.4 x 119.3 [152.3] )
Machine Required floor space *11 dimensions [with control unit door open]
[with control unit door open] mm(inch) 1,080 × 2,106 [2,944] (42.5 × 82.9[115.9]) 1.560 × 2,026 [2,864] (61.4 × 79.8[112.8]) 2,050 × 2,026 [2,864] (80.7 × 79.8[112.8]) 2,410 x 2,233 [3,071] (94.9 x 87.9 [120.9]) Weight kg(lbs) 2,750 (6,063) 3,550 (7,826) 4,150 (9,149)
dimensions
Weight kg(lbs) 2,350 (5,181) 2,400 (5,292) 2,550 (5,622) 3,350 (7,385) Accuracy of bidirectional axis mm(inch) 0.006~0.020 (0.00024~0.00079) 0.006~0.020 (0.00024~0.00079)
Accuracy positioning(ISO230-2: 1988)
Accuracy of bidirectional axis Repeatability of bidirectional axis mm(inch)
Accuracy positioning (ISO230-2:1988) mm(inch) 0.006~0.020 (0.00024~0.00079) 0.006~0.020 (0.00024~0.00079) *3 positioning(ISO230-2: 2014) Less than 0.004 (0.00016) Less than 0.004 (0.00016)
*3 Repeatability of bidirectional axis
positioning (ISO230-2:2014) mm(inch) Less than 0.004 (0.00016) Less than 0.004 (0.00016) Front door 2doors 2doors
Front door 2doors 2doors Standard accessories Instruction Manual (DVD 1 set), leveling bolts (4 pcs.) [R650Xd1: 5 pcs.], leveling plate (4 pcs.) [R650Xd1: 5 pcs.]
Standard accessories Instruction Manual (DVD 1 set), leveling bolts (4 pcs.), leveling plate (4 pcs.) *1 Actual tool weight differs depending on the configuration and center of gravity. The figures shown here are for reference only. *2 Spindle motor output differs depending on the spindle speed.
*1 Actual tool weight differs depending on the configuration and center of gravity. The figures shown here are for reference only. *2 Spindle motor output differs depending on the spindle speed. *3 Measured in compliance with ISO standards and Brother standards. Please contact your local distributor for details. *4 Brother specifications apply to the pull studs for CTS. *5 Measured in
*3 Measured in compliance with ISO standards and Brother standards. Please contact your local distributor for details. *4 Brother specifications apply to the pull studs for CTS. *5 Measured in compliance with JIS B6336-9 and MAS011-1987. *6 Can be increased up to R450Xd1: 200kg, R650Xd1: 300kg (one face) by changing the parameter. Please consult us separately. *7 When using
compliance with JIS B6336-9 and MAS011-1987. *6 Parameter adjustment is required. (Acceleration adjustment and positioning speed are also changed according to the weight.) *7 When using the hydraulic rotary joint, the Y-axis travel becomes 290 mm. *8 Values when the low-floor table is selected. *9 When using high accuracy mode B. *10 Regular air pressure varies depending on the
high accuracy mode B. *8 Regular air pressure varies depending on the machine specifications, machining program details, or use of peripheral equipment. Set the pressure higher than the machine specifications, machining program details, or use of peripheral equipment. Set the pressure higher than the recommend value. *11 When table loading on one face is R450Xd1: 120kg,
recommend value. *9 The machine needs to be equipped with a relocation detection device depending on the destination. Machines equipped with a relocation detection device come with “RD” at R650Xd1: 200kg. *12 The machine needs to be equipped with a relocation detection device depending on the destination. Machines equipped with a relocation detection device come with “RD” at
the end of the model name. *10 Parameter setting must be changed. (Tool magazine indexing time will change.) Max. tool weight 4.0kg cannot be available for the 27,000min-1 specifications. the end of the model name. *13 The value does not include the coolant tank or chip conveyor.
*11 The value does not include the coolant tank.

● When exporting our machine together with additional 1-axis rotary table or compound rotary table (including cases where a rotary table is scheduled to be installed overseas), or exporting the M200/M300Xd1,
U500Xd1, S300/S500/S700Xd1-5AX, or H550Xd1, the machine is deemed to be included in the "applicable listed items" controlled by the Foreign Exchange and Foreign Trade Law of Japan. When exporting the
machine, please obtain required permissions, including an export license, from the Ministry of Economy, Trade and Industry (METI) or Regional Bureaus of Economy, Trade and Industry before shipment. When
re-selling or re-exporting the machine, you may need to obtain permissions from METI, and the government of the country where the machine is installed.
● When exporting our machine together with compound rotary table (including cases where a rotary table is scheduled to be installed overseas), exporting the M200/M300Xd1, U500Xd1, or S300/S500/S700Xd1-5AX,
or exporting the H550Xd1 together with additional 1-axis rotary table (including cases where a rotary table is scheduled to be installed overseas), as a machine conforming to Row 2 of Appended Table 1 of
Export Trade Control Order, a relocation detection device is installed on the machine depending on the destination country. After relocating the machine with the detection device, the machine is locked and any
● Please read the instruction manuals and safety manuals before using Brother products for your own safety. operation is temporarily impossible. Please inform your local distributor of machine relocation in advance and apply to perform the release operation of relocated machine.
When using oil-based coolant oil or when machining the materials which can cause a fire (ex. Magnesium, resin material), customers are requested to take thoroughgoing safety measures against fire. ● In order to operate our machine with an additional axis rotary table installed separately overseas after exporting the machine, a procedure to activate the axis of the rotary table is needed. Please inform your local
Depending on the types of cutting material, cutting tools, coolant oil, lubrication oil, it may have an influence on the machine lifecycle. distributor of these processes in advance, because the predetermined procedure is required to perform the activation. In addition, for export to some countries and regions other than “Group A countries”, it is not
Further questions, please contact our sales representative in charge. possible to install a compound rotary table on the machine or an additional 1-axis rotary table on the H550Xd1 separately overseas after exporting the machine. Please make sure you obtain an export license for
● Leave 700 mm between machines as a maintenance space. the machine together with compound rotary table, or additional 1-axis rotary table for the H550Xd1, before shipment.

13 14
 SPEEDIO Machine Specifications SPEEDIO Machine Specifications

Machine specifications Machine specifications

M200Xd1 / M200Xd1-5AX / M300Xd1 / M300Xd1-5AX / U500Xd1 / U500Xd1 RD *9

Item Item F600X1 / F600X1 RD *9 H550Xd1 / H550Xd1 RD *9
M200Xd1 RD *8 M200Xd1-5AX RD *8 M300Xd1 RD *8 M300Xd1-5AX RD *8 U500Xd1-5AX / U500Xd1-5AX RD *9

CNC-D00 CNC-D00v (DB) 《U500Xd1》CNC-D00

CNC Unit CNC-D00 CNC-D00v (DB) CNC Unit 《U500Xd1-5AX》CNC-D00v(DB) CNC-C00 CNC-D00
X axis mm(inch) 200 (7.9) 300 (11.8) X axis mm(inch) 500 (19.7) 600 (23.6) 550 (21.7)
Y axis mm(inch) 440 (17.3) 440 (17.3) Y axis mm(inch) 400 (15.7) 400 (15.7) 400 (15.7)
Z axis mm(inch) 305 (12.0) 380 (15.0) Z axis mm(inch) 300 (11.8) 350 (13.7) 400 (15.7)
Travels A axis deg. -30~120 -30~120 A axis deg. -30~120 ー ー
C axis deg. 360 360 B axis deg. ー ー 360
Travels
Distance between table top
mm(inch) 150~455 (5.9~17.9) 150~530 (5.9~20.9) C axis deg. 360 ー ー
and spindle nose end
Distance between table top
Work area size mm(inch) ø140 (ø5.5) ø170 (ø6.7) and spindle nose end mm(inch) 145~445 (5.7~17.5) 200~550 (7.8~21.6) ー

Shape of table top In compliance with table nose No.5 of ISO702-4 (JISB6109-2) In compliance with table nose No.6 of ISO702-4 (JISB6109-2) Distance between table top
and spindle center mm(inch) ー ー 100~500 (3.9~19.7)
Table Max.loading capacity
(uniform load) kg(lbs) Table side 40 (88.2) / Tale side 19 (41.9) *9 Table side 75 (165.3) / Tale side 19 (41.9) *9 Distance between table center
and spindle nose end mm(inch) ー ー 150~550 (5.9~21.7)
Max. table load inertia kg∙m2(lb∙inch2) Table side 0.29 (991) / Tale side 0.04 (137) Table side 0.8 (2,734) / Tale side 0.04 (137)
Work area size mm(inch) ø260 (ø10.2) 800 × 400 (31.4 × 15.7) 400 (15.7) x 400 (15.7)
10,000min-1 specifications: 1~10,000
Spindle speed min-1 Table Max.loading capacity kg(lbs) 100 (220) 400 (881) [500 (1,102) *6] 300 (661)
16,000min-1 specifications (Optional): 1~16,000 (uniform load)

Speed during tapping min -1

MAX. 6,000 Max. table load inertia kg∙m2(lb∙inch2) 1.8 (6,151) [2.6 (8,885) *10] ー 3.4 (11,618) [5.4 (18,453) *10]
Spindle Tapered hole 7/24 tapered No.30 12,000min-1 specifications: 1~12,000
10,000min-1 specifications: 1~10,000
Spindle speed min-1 10,000min-1 high-torque specifications: 1~10,000 16,000min-1 specifications (optional): 1~16,000
BT dual contact system (BIG-PLUS) Optional 16,000min-1 specifications (Optional): 1~16,000
10,000min-1 high-torque specifications (optional): 1~10,000

Coolant Through Spindle (CTS) Optional Speed during tapping min-1 MAX. 6,000 MAX. 6,000 MAX. 6,000
Spindle
Tapered hole 7/24 tapered No.30 7/24 tapered No.30 7/24 tapered No.30
Turning spindle Max. Spindle speed min-1 2,000 1,500
Rapid traverse rate(XYZ-area) m/min(inch/min) 50 x 50 x 50 (1,969 x 1,969 x 1,969) BT dual contact system (BIG-PLUS) Optional Optional Optional
Feed Cutting feed rate mm/min(inch/min) X, Y, Z axis: 1~30,000 (0.04~1,181) *7
rate Coolant Through Spindle (CTS) Optional Optional Optional
Indexing feed rate (A and C) min-1 A axis: 60 C axis: 200 A axis: 50 C axis: 200
Rapid traverse rate(XYZ-area) m/min(inch/min) 50 x 50 x 56 (1,969 x 1,969 x 2,205) 50 × 50 × 50 (1,969 × 1,969 × 1,969) 50 x 56 x 56 (1,969 x 2,205 x 2,205)
Tool shank type MAS-BT30
Feed Cutting feed rate mm/min(inch/min) X, Y, Z axis: 1~30,000 (0.04~1,181) *7 X, Y, Z axis: 1~30,000 (0.04~1,181) *7 X, Y, Z axis: 1~30,000 (0.04~1,181) *7
Pull stud type *4 MAS-P30T-2 rate Indexing feed rate (A and C) min-1 A axis: 50 C axis: 75 (60 *10) ー ー
Tool storage capacity pcs. 22/28 *10
ATC Indexing feed rate (B) min-1 ー ー 100 (85 *10)
unit Max. tool length mm(inch) 250 (9.8) *12
Tool shank type MAS-BT30 MAS-BT30 MAS-BT30
Max. tool diameter mm(inch) 80 (3.1)
Pull stud type *4 MAS-P30T-2 MAS-P30T-2 MAS-P30T-2
Max. tool weight *1 kg(lbs) 3 (6.6) <total tool weight : 40(88.2)>
Tool storage capacity pcs. 14/21/28 14/22 30
Tool selection method Random shortcut method ATC
unit Max. tool length mm(inch) 250 (9.8) 250 (9.8) 250 (9.8)
Tool *5 Tool To Tool sec. 0.8 0.8
change Max. tool diameter mm(inch) 110 (4.3) 110 (4.3) / 125 (4.9) No adjacent tool 125 (4.9) *13
time Chip To Chip sec. 1.4 1.5 3.0 (6.6) [4.0 (8.8) *11] / tool, <TOTAL TOOL WEIGHT: 25 (55.1) 3.0 (6.6) / Tool <TOTAL TOOL WEIGHT: 25 (55.1) 4.0 (8.8) / tool,
Max. tool weight *1 kg(lbs)
Main spindle motor 10,000min-1 specifications: 10.1/7.0 for 14 tools, 35 (77.2) for 21or 28 tools> for 14 tools, 40 (88.1) for 22 tools> <TOTAL TOOL WEIGHT: 50 (110.2)>
(10min/continuous) *2 kW Tool selection method Random shortcut method Random shortcut method Random shortcut method
16,000min-1 specifications (optional): 7.4/5.1
Electric
motor Axis feed motor kW X,Y axis: 1.0 Z axis: 1.8 A axis: 0.8 X,Y axis: 1.0 Z axis: 1.8 A axis: 1.35 Tool *5 Tool To Tool sec. 0.6 / 0.7 (14 or 21 tools / 28 tools) 0.7 / 0.8 (14 tools / 22 tools) 1.1
change
Turning spindle motor kW 4.2 4.6 time Chip To Chip sec. 1.2 / 1.3 (14 or 21 tools / 28 tools) 1.6 / 1.7 (14 tools / 22 tools) 2.4
Power supply AC 200 to 230 V±10%, 3-phase, 50/60Hz±2% 12,000min specifications: 10.1/7.0,
-1
Main spindle motor 10,000min-1 specifications: 10.1/7.0,
Power capacity 10,000min-1 specifications: 9.5 Electric kW 10,000min-1 high-torque specifications: 12.8 / 9.2 16,000min-1 specifications (optional): 7.4/5.1
(10min/continuous) *2 16,000min-1 specifications (optional): 7.4/5.1
Power (continuous) kVA motor 10,000min-1 high-torque specifications (optional): 12.8/9.2
16,000min-1 specifications (optional): 9.5
source
Regular air pressure MPa 0.4~0.6 (recommended value 0.5MPa *6) Axis feed motor kW X,Y axis: 1.0 Z axis: 2.0 A axis: 0.9 C axis: 0.55 X,Y axis: 1.0 Z axis: 1.8 X,Z axis: 1.0 Y axis: 1.8 B axis: 1.8
Air supply Power supply AC 200 to 230 V±10%, 3-phase, 50/60Hz±2% AC 200 to 230 V±10%, 3-phase, 50/60Hz±2% AC 200 to 230 V±10%, 3-phase, 50/60Hz±2%
Required flow L/min 175
Height 2,612 (102.9) 2,733 (107.6) 12,000min-1 specifications: 9.5,
mm(inch) Power capacity 10,000min-1 specifications: 9.5,
Power kVA 10,000min-1 high-torque specifications: 10.4 16,000min-1 specifications (optional): 9.5
Machine (continuous) 16,000min-1 specifications (optional): 9.5
dimensions Required floor space *11 mm(inch) 1,280 x 2,667 (50.4 x 105) 1,520 x 2,667 (59.8 x 105) source 10,000min-1 high-torque specifications (optional): 10.4
Weight kg(lbs) 2,700 (5,953) 2,850 (6,283) Regular air pressure MPa 0.4~0.6 (recommended value 0.5MPa *8) 0.4~0.6 (recommended value: 0.5MPa *8) 0.4~0.6 (recommended value 0.5MPa *8)
Air supply
Accuracy of bidirectional axis Required flow L/min 55 45 45
*3
positioning (ISO230-2: 1988) X, Y, Z axis: 0.006~0.020 mm (0.00024~0.00079 inch)
Accuracy (ISO230-2: 2014) A, C axis: 28 sec or less Height mm(inch) 2,748 (108.2) 2,750 (108.2) 2,497 (98.3)
Repeatability of bidirectional axis Machine Required floor space *12
positioning (ISO230-2: 2014) X, Y, Z axis: Less than 0.004 mm (0.00016 inch) A, C axis: 16 sec or less dimensions [with control unit door open] mm(inch) 1.560 x 2,026 [2,864] (61.4 x 79.8 [112.8]) 1,800 × 2,418 [3,256] (70.9 × 95.2 [128.2]) 1,557 x 2,743 [3,581] (61.3 x 108.0 [141.0])
Front door 2doors Weight kg(lbs) 2,650 (5,843) 3,600 (7,937) 2,850 (6,284)
Standard accessories Instruction Manual (DVD 1 set), leveling bolts (5 pcs.), leveling plate (5 pcs.) Accuracy of bidirectional axis
*3 positioning (ISO230-2: 1988) X, Y, Z axis: 0.006~0.020mm (0.00024~0.00079inch) X, Y, Z axis: 0.006~0.020mm (0.00024~0.00079inch) X, Y, Z axis: 0.006~0.020 mm (0.00024~0.00079 inch)
Accuracy (ISO230-2: 2014) A, C axis: 28 sec or less ­ B axis: 28 sec or less
*1 Actual tool weight differs depending on the configuration and center of gravity.The figures shown here are for reference only. *2 Spindle motor output differs depending on the spindle speed.
*3 Measured in compliance with ISO standards and Brother standards. *4 Brother specifications apply to the pull studs for CTS. *5 Measured in compliance with JIS B6336-9 and MAS011-1987.
Repeatability of bidirectional axis X, Y, Z axis: Less than 0.004mm (0.00016inch) X, Y, Z axis: Less than 0.004mm (0.00016inch) X, Y, Z axis: Less than 0.004 mm (0.00016 inch)
positioning (ISO230-2: 2014) A, C axis: 16 sec or less B axis: 16 sec or less
*6 Regular air pressure varies depending on the machine specifications, machining program details, or use of peripheral equipment. Set the pressure higher than the recommended value. *7 When
using high accuracy mode B. *8 The machine needs to be equipped with a relocation detection device depending on the destination. Machines equipped with a relocation detection device come with Front door 2doors 2doors 2doors
“RD” at the end of the model name. *9 The loading capacity on the tail side is 13 kg at the rotating section and 6 kg at the fixed section. *10 For the 28-tool magazine, turning tools cannot be set in Standard accessories Instruction Manual (DVD 1 set),leveling bolts (4 pcs.), leveling plate (4 pcs.)
adjust pods. *11 The value does not include the coolant tank or chip conveyor. *12. Tools with a length of 200 mm or more may contact the jig when the magazine turns, depending on the jig height.
*1 Actual tool weight differs depending on the configuration and center of gravity.The figures shown here are for reference only. *2 Spindle motor output differs depending on the spindle speed.
*3 Measured in compliance with ISO standards and Brother standards. *4 Brother specifications apply to the pull studs for CTS. *5 Measured in compliance with JIS B6336-9 and MAS011-1987.
＊Depending on the type of coolant, it may have a significant influence on the machine lifecycle. It is recommended to use the coolant which *6 Acceleration must be adjusted for Y axis. *7 When using high accuracy mode B. *8 Regular air pressure varies depending on the machine specifications, machining program details, or use of
is commercially designated as high lubricity, for example Emulsion type. Especially, the coolant of chemical solution type (ex. Synthetic peripheral equipment. Set the pressure higher than the recommended value. *9 The machine needs to be equipped with a relocation detection device depending on the destination. Machines
equipped with a relocation detection device come with “RD” at the end of the model name. *10 When using high inertia mode. Parameter setting needs to be changed. *11 Parameter setting needs
type) is prohibited to use, because it may cause machine damages.
to be changed. (Tool indexing time is changed.) *12 The value does not include the coolant tank or chip conveyor. *13 When attaching an adjacent tool, the total diameter of a tool and its adjacent
＊When using CTS (Coolant Through Spindle) function, usage of the coolant of combustible type (ex. Oil-based type) is prohibited. tool must be less than 130 mm.

15 16
 SPEEDIO CNC unit SPEEDIO Option list

*Depending on the model and specifications, some options may be standard equipment or may not be available. For details, refer to the model catalog.

CNC-D00 specifications CNC-C00 specifications Coolant tank S300Xd1

M200Xd1
S500Xd1 W1000Xd2 R450Xd1 R650Xd1 U500Xd1 H550Xd1
S700Xd1 M300Xd1
Model S300/S500/S700Xd1 (-5AX), W1000Xd2, R450/R650Xd1, Model F600X1 Coolant tank 50L ● ●
U500Xd1 (-5AX), M200/M300Xd1 (-5AX), H550Xd1
CNC model CNC-C00 Coolant tank 100L ● ●
CNC model CNC-D00
S300/S500/S700Xd1-5AX, M200/M300Xd1-5AX, U500Xd1-5AX: CNC-D00v (DB)
Control axes 5 axes (X, Y, Z, 2 additional axes) Coolant tank 150L ● ●
Control axes S300/S500/S700Xd1 (-5AX), W1000Xd2,H550Xd1: 5 axes (X,Y,Z, 2 additional axes) Simultaneously Positioning 5 axes (X, Y, Z, 2 additional axes) Coolant tank 200L ● ● ●
controlled axes
R450/R650Xd1: 7 axes (X,Y,Z, 4 additional axes) Interpolation Linear: 4 axes (X, Y, Z, 1 additional axis) Coolant tank 250L ●
M200/M300Xd1 (-5AX), U500Xd1 (-5AX): 5 axes (X,Y,Z, A,C)
Circular: 2 axes Coolant tank 150L with chute ● ●
Simultaneously Positioning 5 axes (X, Y, Z, 2 additional axes)
Helical / conical: 3 axes (X, Y, Z) Coolant tank 200L with chute ● ● ●
controlled axes M200/M300Xd1(-5AX), U500Xd1 (-5AX): 5 axes (X, Y, Z, A, C)
Least input increment 0.001mm, 0.0001inch, 0.001deg.
Coolant tank 250L with chute ●
Interpolation Linear: 4 axes (X, Y, Z, 1 additional axis)
S300/S500/S700Xd1-5AX, M200/M300Xd1-5AX, U500Xd1-5AX: Max. programmable dimension ±9999.999mm, ±999.9999inch Chip conveyor tank (360∼400L) ● ● ● ● ●
5 axes (X, Y, Z, 2 additional axes)
Display 12.1-inch color LCD * Coolant tanks other than 50L and 100L can be selected for Coolant Through Spindle CTS 1.5 MPa with cyclone filter. However, some coolant tanks are only available for CTS 1.5MPa with cyclone filter.
Circular : 2 axes * Capacity of the chip conveyor tank differs depending on the model, so please refer to the model catalog for details.
Memory capacity Approx.100 Mbytes (Total capacity of program and data bank)
Hellical/conical: 3 axes (X, Y, Z)
External communication USB memory interface, Ethernet, RS232C (optional)
S300/S500/S700Xd1-5AX, M200/M300Xd1-5AX, U500Xd1-5AX:
4 axes (Up to 3 axes for Linear + 1 axis for No.of registrable programs 4,000 (Total capacity of program and data bank)
rotation, 2 axes for linear + 2 axes for rotation)
Program format NC language, conversation (changed by parameter), Option common
Least input increment 0.001mm, 0.0001inch, 0.001deg. conversion from conversation program to NC
language program available • BT dual contact spindle • Area sensor • RS232C 25-pin connector at control box • EXIO board assembly
Max. programmable dimension ±999999.999mm, ±99999.9999inch
• Coolant Through Spindle (CTS) 1.5MPa *1 • Side cover with transparent window • Master on circuit ①EXIO board, input32/output32, additional #1
Display 15-inch color LCD touch display * “Control axes” and “Simultaneously controlled axes” indicate the maximum number of
axes, which will differ depending on the destination country and the machine • Tool washing, air-assisted type • Specified color • 100V outlet in control box ②EXIO board, input32/output32, additional #2
Memory capacity 500MB, 3GB (optional) specifications. • Chip shower • Tool breakage detector, touch type • Data protection switch, key type • Industrial network
S300/S500/S700Xd1-5AX, M200/M300Xd1-5AX, U500Xd1-5AX: 3GB * Ethernet is a registered trademark of Xerox Corporation in the United States. • Fixture shower valve unit • Manual pulse generator • Parts name sticker set ①CC-Link, master station
(Total capacity of program and data bank)
• Cleaning gun with enable switch *2 • Transformer box ②CC-Link, remote device station
External communication USB memory interface, Ethernet, RS232C (optional)
• Automatic oil lubricator • Spindle override • Memory expansion 3GB / 500MB *3 ③PROFIBUS DP, slave
No.of registrable programs 4,000 (Total capacity of program and data bank) • Automatic grease lubricator • Switch panel 8 or 10 holes • High accuracy mode BⅡ, look-ahead 1,000 / ④DeviceNet, slave
Program format NC language, conversatconversation (changed by parameter), • Work light, 1 or 2 lamps • power supply expantion 50A 200 blocks, with smooth path offset *4 ⑤PROFINET, slave *5
conversation from conversation program to NC language program available • Signal light, 1, 2, or 3 lamps • PLC programming software ⑥EtherNet/IP, slave *5
• Automatic door with switch panel 10 holes
M200/M300Xd1(-5AX),H550Xd1: NC language
*Conversation language not available *1/ The pressure resistance of the CTS is 3 MPa. Pump and tank are not included. *2/ No enable switch for F600X1. *3/ 500MB for F600X1. *4/ Look-ahead 200blocks for F600X1. *5/ ⑤ and ⑥ not available
for F600X1.

NC functions
CNC-D00 CNC-C00
Option by model S300Xd1
M200Xd1
Operation Monitoring Support apps Turning function *3 S500Xd1 W1000Xd2 R450Xd1 R650Xd1 U500Xd1 H550Xd1
S700Xd1 M300Xd1
●● Dry Run ●● Machining load monitoring ● Adjust machine parameters ●● Constant peripheral speed control
●● Machine lock ●● ATC monitoring ● ATC tool ●● Feed per revolution control Rotary table T-200Ad / T-200A *6 ● ● ● ● ●
●● Restart ● Overload prediction ● Tool life ●● Tool position compensation XYZ
●● Rapid traverse override ●● Waveform display / waveform output to memory card ● Waveform display ●● Nose R compensation Coolant Through Spindle (CTS) 7MPa *7 ● ● ● ● ● ● ●
●● Cutting feed override ●● Heat expansion compensation systemⅡ (X, Y, Z axes) ● Production performance ●● Tread cutting Head coolant nozzle ● ● ● ● ● ● ● ●
●● Background editing ● Production performance ● Power consumption
●● Screen shot ● Power consumption ● Recovery support Conversation language mode only *4
Column coolant nozzle ● ● ● ● ● ●
●● Operation level ●● Tool life / Spare tool ● Inspection ●● Operation program Coil conveyor *8 ●
●● External input signal key ● Stuck chips detection function ● PLC (LD/ST/FBD) ●● Schedule program
●● Shortcut key ●● Automatic tool selection
Mesh basket for collecting chips ● ● ● ● ● ● ● ●
(optional) Maintenance Accessories ●● Automatic cutting condition setting High column, 150mm, 250mm, or 350mm *9 ● ●
●● Spindle override ●● Tap return function ● File viewer ●● Automatic tool length compensation setting
●● Status log ● Notebook ●● Automatic cutter compensation setting
Additional axis cable ● ● ● ● ● ●
Programing ●● Alarm log ● Calculator ●● Automatic calculation of unknown number input Top cover ● ● ● ● ● ●
●● Absolute / incremental ●● Operation log ● Register shortcut ●● Machining order control Grip cover for tool magazine ● ● ● ● ● ● ●
●● Inch / metric ●● Maintenance notice ●● Display off
●● Coordinate system setting ●● Motor insulation resistance measurement Breaker handle cover ● ● ●
●● Corner C / Corner R ●● Tool washing filter with filter clogging detection NC language mode only Origin alignment mark ● ● ● ● ● ● ●
●● Rotational transformation ● Batteryless encoder ●● Menu programing
●● Synchronized tap ● Brake load rest ●● Local coordinate system Side door with transparent window, right side ● ● ●
●● Subprogram ●● Expanded workpiece coordinate system Pneumatic relay box 12P ● ●
●● Graphic display Automation / Network ●● One-way positioning
●● Computer remote ●● Inverse time feed Hydraulic rotary joint 4P ● ●
Measurement ● OPC UA ●● Programable data input Rotary joint 4P ●
●● Automatic workpiece measurement *1 ●● Auto notification ●● Tool length compensation
●● Tool length measurement ●● Built-in PLC ●● Cutter compensation Hydraulic rotary cylinder ●
(optional) ●● Scaling A-axis clamp (Single・Double) ●
High speed and High accuracy ●● CC-Link, master station ●● Mirror image
● Machining parameter setting ●● CC-Link, remote device station ● External sub program call Rotary joint 6P ●
●● High-accuracy mode AⅢ ●● PROFIBUS DP, slave ●● Macro Rotary joint 9+1P ●
● High-accuracy mode BⅠ ●● DeviceNet, slave ●● Operation in tape mode
(Look-ahead 160blocks) ● PROFINET, slave ● Multiple skip function Table light ● ●
● High-accuracy mode BⅠ ● EtherNet/IP, slave (optional) Outside rotary table switch for 1 or 2 axes ● ●
(Look-ahead 40blocks) ●● Submicron command *2
●● Backlash compensation Energy saving ●● Interrupt type macro
Rotary table switch (for B-axis, for additional axes) ●
● Tool center point control *5 ●● Automatic power off ●● Rotary fixture offset Turning diameter enlargement, ø1,100mm (R450Xd1)/ø1,300mm (R650Xd1) ● ●
(Look-ahead 1,000 blocks) ●● Servomotor off standby mode ●● Feature coordinate setting function
(optional) ●● Automatic coolant off ●● Involute interpolation
Low-floor table ● ●
● High-accuracy mode BⅡ ●● Automatic work light off Side magazine switch ●
(Look-ahead 1,000blocks, with smooth path offset) ●● Chip shower off delay
Front switch panel 10 holes ● ●
● High-accuracy mode BⅡ
(Look-ahead 200blocks, with smooth path offset) Outside start swutch on the side ●
● High-speed processing Folding door (two-door) ● ● ● ●
*1/ Measuring instrument needs to be prepared by users. *2/ When the submicron command is used, changing to the conversation program is disabled. *3/ Only for M200/M300Xd1. *4/ Conversation language
not available for M200/M300Xd1 and H550Xd1. *5/ Only for the S300/S500/S700Xd1-5AX, M200/M300Xd1-5AX and U500Xd1-5AX. *6/ T-200A is available for F600X1. *7/ Pump and tank are not included. *8/ A chip conveyor is required when selecting coil conveyor. *9/ 350mm high column is only available for W1000Xd2.

17 18
 Global Service Sites

Brother Technology Center Chicago Brother Technology Center Queretaro

BROTHER INTERNATIONAL CORP. BROTHER INTERNATIONAL DE MÉXICO, S.A. DE C.V.
2200 North Stonington Avenue, Suite 270, Hoffman Estates, IL 60169, U.S.A. Calle 1 No.310 Int 15, Zona Industrial Jurica, Parque Industrial Jurica,
PHONE:(1)224-653-8415 FAX:(1)224-653-8821 Queretaro, QRO C.P. 76100 México
PHONE:(52)55-8503-8760 FAX:(52)442-483-2667

Brother Technology Center Frankfurt Brother Technology Center Bangkok

BROTHER INTERNATIONALE INDUSTRIEMASCHINEN GmbH BROTHER COMMERCIAL (THAILAND) LTD.
Hoechster Str.94, 65835 Liederbach, Germany 317 Pattanakarn Road, Pravet Sub-District, Pravet District, Bangkok 10250, Thailand
PHONE:(49)69-977-6708-0 FAX:(49)69-977-6708-80 PHONE:(66)2321-5910 FAX:(66)2321-5913

Brother Technology Center Bengaluru Brother Technology Center Gurugram

BROTHER MACHINERY INDIA PVT LTD.
BROTHER MACHINERY INDIA PVT LTD.
SB-111-112, 1st Stage, 2nd Cross, Peenya Indl Estate, Bengaluru - 560058 Karnataka, India Plot No. 60, Sector 34, HSIIDC, Gurugram, Haryana 122001, India
PHONE:(91)80-43721645 PHONE:(91)0124-4449900

Brother Technology Center Dongguan

Brother Technology Center Shanghai BROTHER MACHINERY (SHANGHAI) LTD.
BROTHER MACHINERY (SHANGHAI) LTD. Room 103, Building 1, No.2 Nanbo Road,
Unit 01, 5/F., No.799, West Tianshan Rd., ChangNing District Shanghai 200335, China Songshan Lake District, Dongguan City, Guangdong Province, China
PHONE:(86)21-2225-6666 FAX:(86)21-2225-6688 PHONE:(86)769-2238-1505 FAX:(86)769-2238-1506

Brother Technology Center Ningbo

Brother Technology Center Chongqing BROTHER MACHINERY (SHANGHAI) LTD.
BROTHER MACHINERY (SHANGHAI) LTD. 1F, Building 1, No. 102, Hongtang South Road West Section, Jiangbei District, Ningbo City,
Room 30, 31, NO.104 Cuibai Road, Dadukou District, Chongqing Province, 400084, China Zhejiang Province, China
PHONE:(86)23-6865-5600 FAX:(86)23-6865-5560 PHONE:(86)574-87781232 FAX:(86)574-88139792

Nanjing Office
BROTHER MACHINERY (SHANGHAI) LTD.
503 Room,Building No.1,No.39,Dongcun Road,Jiangning District,Nanjing City, Jiangsu Province, China
PHONE:(86)25-87185503
Figures in brackets ( ) are the country codes.

Please check here for detailed information

and the latest information of the base.

https://machinetool.global.brother/

Specifications may be subject to change without any notice.

Machinery Business Division

1-5, Kitajizoyama, Noda-cho, Kariya-shi, Aichi-ken 448-0803, Japan
https://www.brother.co.jp

The information in this catalogue is current as of August 2023. ver.2308