REVIEWER

Test I. MULTIPLE CHOICE:

Directions: Read and analyze carefully the statement and select the most appropriate answer. Write the
letter of the correct answer.
1. Which of the following is not a plane of projection?
A. Frontal plane B. Profile plane C. Horizontal plane D. Bottom plane
2. One of these should not be dimensioned unless necessary. What is this line?
A. Center line B. Cutting plane line C. Visible line D. Hidden line
3. What lines show the surface or edges hidden from view by other parts of the object?
A. Hidden lines B. Center lines C. Cutting plane lines D. Visible lines
4. Holes should be dimensioned from what area?
A. Edge-to-edge B. Edge to center C. Center to center D. Center to edge
5. What lines are used to locate center of object, arcs and circles?
A. Dimension lines B. Cutting plane lines C. Center lines D. Extension lines
6. How would you compare top view from right side view of an object?
A. Top view has length and width while right side view has also width and height
B. Top view has width while right side view has width also
C. Top view is directly on top of the front view
D. Top view is found below the right side view
7. What line is used to show clearly the dimension limits of an object?
A. Center line B. Extension line C. Leader line D. Dimension line
8. What line is leading from a dimension value or an explanatory note to the feature on the drawing to which the
note applies?
A. Dimension line B. Extension line C. Center line D. Leader line
9. What lines are used to indicate an imaginary cut through an object along the line?
A. Cutting plane lines B. Dimension lines C. Hidden lines D. Center lines
10. What value that gives the actual distance of the objects?
A. Number B. Value C. Numerical value D. Dimension line
11. What view does a top plane directly show?
A. Top view B. Bottom view C. Left side view D. Front view
12. What part of dimensioning means explanatory information along with a size?
A. Size B. Value C. Arrowheads D. Notes
13. Dimension lines must be kept at least _______ away from the object line.
A. 1/8 inch B. ¼ inch C. 3/8 inch D. ½ inch
14. What type of drawing arrowheads usually made thinner and slightly longer than the open style that has no
curvature to the sides?
A. Close type B. Open style C. Solid style D. Close and open type
15. What is the method of representing the exact shape of an object into two or more views or planes?
A. Pictorial B. Orthos C. Graphos D. Orthographic
16. Which of the following lines are light in weight and broken in the middle to provide space for dimensions?
A. Break lines B. Section lines C. Dimension lines D. Extension lines
17. What view does vertical planes show?
A. From the top B. From the side C. From the rear D. From the front
18. View found on top of the front view which shows the shape, length and width of the object.
A. Front view B. Top view C. Right side view D. Left side view
19. What lines are used to show the visible outline of an object?
A. Hidden lines B. Cutting plane lines C. Center lines D. Visible lines
20. View found on the right side of the front view, which shows the shape, height and width of the object.
A. Right view B. Back view C. Left side view D. Right side view
21. View found at the bottom of the top view which shows the length and width of the object.
A. Right side view B. Left side view C. Bottom view D. Right view
22. What system of placing dimensions is sometimes called horizontal system?
A. Directional B. Aligned C. Unidirectional D. Horizontal
23. Why is it that a surface parallel to a plane of projection is shown in its true size?
A. Because it is in line with the plane
B. Because it is perpendicular in the plane
C. Because the surface intersects the plane
D. Because the surface is inclined with the plane
24. What will you produce to a line projected perpendicularly to a plane of projection?
A. Surface B. Point C. Line D. View
25. What would happen if a surface is inclined to a plane of projection?
A. Lengthen B. Distorted C. Foreshortened D. Perpendicular
26. What is the set of conventional line symbols used in orthographic drawings?
A. Alphabet B. Sets of line C. Alphabet of lines D. Orthographic
27. How would you dimension or measure angles?
A. By means of vertical lines
B. By means of arcs and arrowheads
C. By means of horizontal lines
D. By means of inclined lines
28. What are the light broken lines which are sometimes used as extension line?
A. Center lines B. Extension lines C. Arrowheads D. Leader line
29. What part of the circle could give the dimensions of the circles?
A. Diameter B. Radius C. Secant D. Circumference
30. Dimensions must be kept ______________ the views.
A. Left side B. Right side C. Between D. At the bottom
31. What is the main idea of using line symbols in the drawing?
A. For decoration C. To represent the kind of construction
B. To be more attractive D. Just to complete the drawing
32. What is the method of placing the exact numerical value of an object in the drawing in complete and proper
manner?
A. Dimension line B. Numerical value C. Leader line D. Dimensioning
33. What do you think is the purpose of detail dimensions that should be kept in one line?
A. Avoid cluttering C. Easier reading
B. Avoid confusion D. All of these
34. View found below the top view which shows the shape, length and height of the object.
A. Front view B. Top view C. Right side view D. Left side view
35. What is the distance of the extension lines from the object?
A. 1/32” B. 1/16” C. 3/16” D. 1/8”
36. Line parallel to a plane of projection will show in its _________ on the plane.
A. True length B. True width C. True height D. True depth
37. Which of the following is recommended when dimensioning is in limited space?
A. Just insert the dimension no matter how small the size
B. Just indicate the dimension line no matter how narrow the space
C. Arrowheads should be reversed and the size should be transferred outside the dimension line
D. Arrowheads should be placed in a normal manner.
38. What part of the circle could give the dimensions of the arcs?
A. Circumference B. Radius C. Diameter D. Chord
39. The smaller or detail dimensions should be __________ from the view.
A. Nearest B. Farthest C. Extreme far D. Near
40. What part of dimension lines indicates the direction in which the value applies?
A. Horizontal line B. Open line C. Solid line D. Arrowheads