Image may differ from product. See technical specification for details.
FY 50 TF
Square flanged ball bearing unit with set screw locking, cast iron housing, ISO
These square flanged ball bearing units are compliant with ISO standards. They consist of
an insert bearing, with an extended inner ring and set screw locking, and are suitable for
applications where the direction of rotation is constant or alternating. The bearing is
mounted in a cast iron housing, which can be bolted to a machine wall or frame. Ball
bearing units can accommodate moderate initial misalignment, but normally do not permit
axial displacement.
Resist high levels of contamination
Designed for high temperatures and speeds
Accommodate relatively heavy loads
Cost-effective
Overview
Dimensions
Shaft diameter 50 mm
Housing overall width 43 mm
Width, total 60.6 mm
Centre distance between bolt holes 111 mm
Bearing width, total 51.6 mm
Performance
Basic dynamic load rating 35.1 kN
Basic static load rating 23.2 kN
Limiting speed 4 000 r/min
Note Limiting speed with shaft tolerance h6
Properties
Housing type Flanged
Flanged housing type Square
Number of bolt holes for fasteners 4
Fastening bolt hole type Plain
Retaining feature, inner ring Set screws
Bore type Cylindrical
Rubber seating ring Without
Material, housing Cast iron
Material, bearing Bearing steel
Coating Without
Sealing, bearing Seal and flinger on both sides
Sealing type Contact, standard
Sealing, unit Optional end cover
Lubricant Grease
Relubrication hole With
Grease fitting With
Logistics
Product net weight 2.25 kg
eClass code 23-05-08-02
UNSPSC code 31171536
Technical specification
Compliance with standard ISO
Purpose specific For material handling applications
Material, housing Cast iron
Sealing, bearing Seal and flinger on both sides
Sealing type, bearing Contact, standard
Sealing, unit Optional end cover
Coating Without
Dimensions
d 50 mm Bore diameter
d1 ≈ 62.51 mm Outer diameter of inner ring
A 43 mm Width of housing
A1 15 mm Flange width
A3 3.2 mm Depth of centring recess
A5 33 mm Standout of end cover
B 51.6 mm Width of inner ring
B1 51.6 mm Overall bearing width
Distance from locking device side face
B4 9 mm
to thread centre
Db1 107 mm Top external diameter
Db2 118 mm Base external diameter
Dc 125.4 mm Diameter of housing centering recess
J 111 mm Distance between attachment bolts
L 143 mm Overall length
N 18 mm Diameter of attachment bolt hole
Distance from locking device side face
s1 32.6 mm
to raceway centre
T 60.6 mm Overall width
T HRE ADE D HOLE
RG 1/4-28 UNF Housing thread for grease fitting
R1 28.5 mm Axial position of the housing thread
GRE ASE FI T T I NG
Diameter of head sphere of grease
DN 6.5 mm
fitting
SWN 7 mm Hexagonal key size for the grease fitting
GN 1/4-28 SAE-LT Thread of grease fitting
D OW E L P I NS
J6 129 mm Distance of dowel pins
J7 35.5 mm Axial offset of dowel pins
N4 4 mm Recommended diameter for dowel pins
Calculation data
Basic dynamic load rating C 35.1 kN
Basic static load rating C0 23.2 kN
Fatigue load limit Pu 0.98 kN
Limiting speed 4 000 r/min
Limiting speed with shaft tolerance h6
Mass
Mass bearing unit 2.3 kg
Mounting information
Set screw G2 M10x1
Hexagonal key size for set screw 5 mm
Recommended tightening torque for set
16.5 N·m
screw
Recommended diameter for
G 16 mm
attachment bolts, mm
Recommended diameter for
G 0.625 in
attachment bolts, inch
Compatible products
Component
Square flanged housing for insert bearings, cast iron FY 510 M
Insert bearing with set screw locking and extended inner ring YAR 210-2F
Recommended product
End cover for bearing units ECY 210
More Information
Product details
Flanged units to ISO standards
Flanged units to North American standards
Flanged units to Japanese Industrial Standards (JIS)
Flanged units, not standardized (SKF Food Line)
Permissible misalignment
Locating/non-locating support
Loads
Temperature limits
Permissible speed
Lubrication
Mounting and dismounting
Ordering information
Designation system
Engineering information
e Principles of ball bearing units selection and application - Download catalogue (4.9 MB)
Principles of selecting mounted bearing solutions
Bearing failure and how to prevent it
Tools
Bearing Select
Engineering Calculator
Rolling bearings mounting and dismounting instructions
Terms of use
By accessing and using this website / app owned and published by AB SKF (publ.) (556007-3495 · Gothenburg) (“SKF”), you
agree to the following terms and conditions:
Warranty Disclaimer and Limitation of Liability
Although every care has been taken to assure the accuracy of the information on this website / app, SKF provides this
information "AS IS" and DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. You acknowledge that your use of this
website / app is at your sole risk, that you assume full responsibility for all costs associated with use of this website / app,
and that SKF shall not be liable for any direct, incidental, consequential, or indirect damages of any kind arising out of your
access to, or use of the information or software made available on this website / app.
Any warranties and representations in this website / app for SKF products or services that you purchase or use will be
subject to the agreed upon terms and conditions in the contract for such product or service.
Further, for non-SKF websites / apps that are referenced in our website / app or where a hyperlink appears, SKF makes no
warranties concerning the accuracy or reliability of the information in these websites / apps and assumes no responsibility
for material created or published by third parties contained therein. In addition, SKF does not warrant that this website / app
or these other linked websites / apps are free from viruses or other harmful elements.
Third Party Services
When viewing YouTube content via the SKF website(s) (i.e. using YouTube API Services), you agree to be bound by the
YouTube Terms of Service.
Copyright
Copyright in this website / app copyright of the information and software made available on this website / app rest with SKF
or its licensors. All rights are reserved. All licensed material will reference the licensor that has granted SKF the right to use
the material. The information and software made available on this website / app may not be reproduced, duplicated,
copied, transferred, distributed, stored, modified, downloaded or otherwise exploited for any commercial use without the
prior written approval of SKF. However, it may be reproduced, stored and downloaded for use by individuals without prior
written approval of SKF. Under no circumstances may this information or software be supplied to third parties.
This website /app includes certain images used under license from Shutterstock, Inc.
Trademarks and Patents
All trademarks, brand names, and corporate logos displayed on the website / app are the property of SKF or its licensors,
and may not be used in any way without prior written approval by SKF. All licensed trademarks published on this website /
app reference the licensor that has granted SKF the right to use the trademark. Access to this website / app does not grant
to the user any license under any patents owned by or licensed to SKF.
Changes
SKF reserves the right to make changes or additions to this website / app at any time.
