UNIT – III

Design of Antennas
 Helical Antenna

 Helical antenna is an example of wire antenna and

itself forms the shape of a helix.
 The frequency range of operation of helical antenna
is around 30MHz to 3GHz.
 This antenna works in VHF and UHF ranges.
Construction & Working of Helical Antenna

 Helical antenna or helix antenna is the antenna in

which the conducting wire, a thick cupper wire is
wound in helical shape and connected to the ground
plate with a feeder line.
 It is the simplest antenna, which
provides circularly polarized waves.
 It is used in extra-terrestrial communications in
which satellite relays etc., are involved.
 It consists of a helix of thick copper wire or tubing wound
in the shape of a screw thread used as an antenna in
conjunction with a flat metal plate called a ground plate.
 One end of the helix is connected to the center conductor
of the cable and the outer conductor is connected to the
ground plate.
 The radiation of helical antenna depends on the diameter
of helix, the turn spacing and the pitch angle.
 Pitch angle is the angle between a line tangent to the
helix wire and plane normal to the helix axis.
 Modes of Operation

 The predominant modes of operation of a helical

antenna are −
 Normal or perpendicular mode of radiation.
 Axial or end-fire or beam mode of radiation.
 Normal mode

 In normal mode of radiation, the radiation field is

normal to the helix axis.
 The radiated waves are circularly polarized.
 This mode of radiation is obtained if the dimensions
of helix are small compared to the wavelength.
 The radiation pattern of this helical antenna is a
combination of short dipole and loop antenna.
 The above figure shows the radiation pattern for
normal mode of radiation in helical antenna.
 It depends upon the values of diameter of
helix, D and its turn spacing, S.
 Drawbacks of this mode of operation are low
radiation efficiency and narrow bandwidth.
 Hence, it is hardly used.
 Axial mode

 In axial mode of radiation, the radiation is in the

end-fire direction along the helical axis and the
waves are circularly or nearly circularly polarized.
 This mode of operation is obtained by raising the
circumference to the order of one
wavelength (λ) and spacing of approximately λ/4.
 The radiation pattern is broad and directional along
the axial beam producing minor lobes at oblique
angles.
 The figure shows the radiation pattern for axial mode
of radiation in helical antenna.
 If this antenna is designed for right-handed
circularly polarized waves, then it will not receive
left-handed circularly polarized waves and vice versa.
 This mode of operation is generated with great ease
and is more practically used.
Advantages
Disadvantages

 The following are the  The following are the

advantages of Helical
antenna − disadvantages of
 Simple design Helical antenna −
 Highest directivity  Antenna is larger and
 Wider bandwidth requires more space
 Can achieve circular
polarization  Efficiency decreases
 Can be used at HF & with number of turns
VHF bands also.
 Applications

 The following are the applications of Helical antenna −

 A single helical antenna or its array is used to transmit
and receive VHF signals
 Frequently used for satellite and space probe
communications
 Used for telemetry links with ballastic missiles and
satellites at Earth stations
 Used to establish communications between the moon
and the Earth
 Applications in radio astronomy.
 Yagi-Uda antenna

 Yagi-Uda antenna is the most commonly used

type of antenna for TV reception over the last few
decades.
 It is the most popular and easy-to-use type of
antenna with better performance, which is famous
for its high gain and directivity
 Frequency range
 The frequency range in which the Yagi-Uda antennas
operate is around 30 MHz to 3GHz which belong
to the VHF and UHF bands.
 Construction of Yagi-Uda Antenna

 The parasitic elements and

the dipole together form
this Yagi-Uda antenna.
 The figure shows a Yagi-
Uda antenna.
 It is seen that there are
many directors placed to
increase the directivity of
the antenna.
 The feeder is the folded
dipole.
 The reflector is the lengthy
element, which is at the
end of the structure.
 The figure depicts a clear form of the Yagi-Uda antenna.
 The center rod like structure on which the elements are
mounted is called as boom.
 The element to which a thick black head is connected is
the driven element to which the transmission line is
connected internally, through that black stud.
 The single element present at the back of the driven
element is the reflector, which reflects all the energy
towards the direction of the radiation pattern.
 The other elements, before the driven element, are
the directors, which direct the beam towards the desired
angle.
 Designing

 For this antenna to be designed, the following design

specifications should be followed.
 Radiation Pattern

 The directional pattern of the Yagi-Uda antenna is highly

directive as shown in the figure given below.
 The minor lobes are suppressed and the directivity of the
major lobe is increased by the addition of directors to the
antenna.
Advantages Disadvantages

 The following are the  The following are the

advantages of Yagi-Uda
antennas − disadvantages of Yagi-
 High gain is achieved. Uda antennas −
 High directivity is
achieved.  Prone to noise.
 Ease of handling and  Prone to atmospheric
maintenance.
effects.
 Less amount of power is
wasted.
 Broader coverage of
frequencies.
 Applications

 The following are the applications of Yagi-Uda

antennas −
 Mostly used for TV reception.
 Used where a single-frequency application is needed.
 Aperture antenna

 An Antenna with an aperture at the end can be termed as

an Aperture antenna.
 Waveguide is an example of aperture antenna.
 The edge of a transmission line when terminated with an
opening, radiates energy.
 This opening which is an aperture, makes it
an Aperture antenna.
 The main types of aperture antennas are −
 Wave guide antenna
 Horn antenna
 Slot antenna
 Waveguide Antenna

 A Waveguide is capable of radiating energy when

excited at one end and opened at the other end.
 The radiation in wave guide is greater than a two-wire
transmission line.
 Frequency Range
 The operational frequency range of a wave guide is
around 300MHz to 300GHz.
 This antenna works in UHF and EHF frequency ranges.
The following image shows a waveguide.
 This waveguide with
terminated end, acts as an
antenna.
 But only a small portion of the
energy is radiated while a large
portion of it gets reflected back
in the open circuit.
 It means VSWR (voltage
standing wave ratio, discussed
in basic parameters chapter)
value increases.
 The diffraction around the
waveguide provides poor
radiation and non-directive
radiation pattern.
 Radiation Pattern
 The radiation of waveguide
antenna is poor and the pattern
is non-directive, which means
omni-directional.
 An omni-directional pattern
is the one which has no certain
directivity but radiates in all
directions, hence it is called
as non-directive radiation
pattern.
 The above figure shows a top
section view of an omni-
directional pattern, which is
also called as non-directional
pattern.
 The two-dimensional view is a
figure-of-eight pattern.
Advantages Disadvantages

 The following are the  The following are the

advantages of Aperture disadvantages of
antenna − Aperture antenna −
 Radiation is greater  VSWR increases
than two-wire  Poor radiation
transmission line
 Radiation is Omni-
directional
 Applications

 The following are the applications of Aperture

antenna −
 Micro wave applications
 Surface search radar applications
 The waveguide antenna has to be further modified to
achieve better performance, which results in the
formation of Horn antenna.
 Horn Antenna

 To improve the radiation efficiency and directivity of the

beam, the wave guide should be provided with an
extended aperture to make the abrupt discontinuity of
the wave into a gradual transformation.
 So that all the energy in the forward direction gets
radiated. This can be termed as Flaring.
 Now, this can be done using a horn antenna.
 Frequency Range
 The operational frequency range of a horn antenna is
around 300MHz to 30GHz. This antenna works
in UHF and SHF frequency ranges.

 Construction & Working of Horn Antenna

 The energy of the beam when

slowly transform into radiation, the
losses are reduced and the
focussing of the beam improves.
 A Horn antenna may be
considered as a flared out wave
guide, by which the directivity is
improved and the diffraction is
reduced.
 The above image shows the model
of a horn antenna.
 The flaring of the horn is clearly
shown.
 There are several horn configurations out of which, three
configurations are most commonly used.

Sectoral horn
 This type of horn antenna, flares out in only one direction.
 Flaring in the direction of Electric vector produces the sectorial E-
plane horn.
 Similarly, flaring in the direction of Magnetic vector, produces
the sectorial H-plane horn.
Pyramidal horn
 This type of horn antenna has flaring on both sides.
 If flaring is done on both the E & H walls of a rectangular
waveguide, then pyramidal horn antenna is produced.
 This antenna has the shape of a truncated pyramid.
Conical horn
 When the walls
of a circular wave
guide are flared,
it is known as
a conical horn.
 This is a logical
termination of a
circular wave
guide.
 Flaring helps to match the antenna impedance with the
free space impedance for better radiation.
 It avoids standing wave ratio and provides greater
directivity and narrower beam width.
 The flared wave guide can be technically termed
as Electromagnetic Horn Radiator.
 Flare angle, Φ of the horn antenna is an important factor
to be considered.
 If this is too small, then the resulting wave will be
spherical instead of plane and the radiated beam will not
be directive.
 Hence, the flare angle should have an optimum value and
is closely related to its length.
 Combinations

 Horn antennas, may also be combined with parabolic

reflector antennas to form special type of horn antennas.
These are −
 Cass-horn antenna
 Hog-horn or triply folded horn reflector
Cass-horn antenna
 In Cass-horn antenna, radio waves are collected by the large
bottom surface, which is parabolically curved and reflected
upward at 45° angle.
 After hitting top surface, they are reflected to the focal point.
 The gain and beam width of these are just like parabolic
reflectors.
hog-horn
 In hog-horn antenna, a parabolic cylinder is joined to
pyramidal horn, where the beam reaches apex of the horn.
 It forms a low-noise microwave antenna.
 The main advantage of hog-horn antenna is that its receiving
point does not move, though the antenna is rotated about its
axis.
 Radiation Pattern

 The radiation pattern of a horn antenna is a Spherical Wave front.

 The following figure shows the radiation pattern of horn antenna.
 The wave radiates from the aperture, minimizing the diffraction of
waves. The flaring keeps the beam focussed.
 The radiated beam has high directivity.
Advantages Disadvantages

 The following are the  The following are the

advantages of Horn disadvantages of Horn
antenna −
antenna −
 Small minor lobes are
formed  Designing of flare
 Impedance matching is angle, decides the
good directivity
 Greater directivity  Flare angle and length
 Narrower beam width of the flare should not
 Standing waves are avoided be very small
 Applications

 The following are the applications of Horn antenna −

 Used for astronomical studies
 Used in microwave applications
 Parabolic Reflectors

 Parabolic Reflectors are Microwave antennas.

 The frequency range used for the application of Parabolic reflector
antennas is above 1MHz.
 These antennas are widely used for radio and wireless applications.
 Principle of Operation
 The standard definition of a parabola is - Locus of a point, which moves
in such a way that its distance from the fixed point (called focus) plus
its distance from a straight line (called directrix) is constant.
 The following figure shows the geometry of parabolic reflector.
 The point F is the focus (feed is given) and V is the vertex.
 The line joining F and V is the axis of symmetry.
 PQ are the reflected rays where L represents the line directrix on which the reflected points lie (to
say that they are being collinear).
 Hence, as per the above definition, the distance between F and L lie constant with respect to the
waves being focussed.
 The reflected wave forms a collimated wave front, out of the parabolic
shape.
 The ratio of focal length to aperture size (ie., f/D) known as “f over D
ratio” is an important parameter of parabolic reflector. Its value varies
from 0.25 to 0.50.
 The law of reflection states that the angle of incidence and the angle of
reflection are equal.
 This law when used along with a parabola, helps the beam focus.
 The shape of the parabola when used for the purpose of reflection of
waves, exhibits some properties of the parabola, which are helpful for
building an antenna, using the waves reflected.
 Properties of Parabola

 All the waves originating from focus, reflects back to the parabolic axis.
Hence, all the waves reaching the aperture are in phase.
 As the waves are in phase, the beam of radiation along the parabolic
axis will be strong and concentrated.
 Following these points, the parabolic reflectors help in producing high
directivity with narrower beam width.
 Construction & Working of a Parabolic Reflector

 If a Parabolic Reflector antenna is used for transmitting a signal, the

signal from the feed, comes out of a dipole or a horn antenna, to focus
the wave on to the parabola.
 It means that, the waves come out of the focal point and strike the
Paraboloidal reflector.
 This wave now gets reflected as collimated wave front, as discussed
previously, to get transmitted.
 The same antenna is used as a receiver.
 When the electromagnetic wave hits the shape of the parabola, the
wave gets reflected onto the feed point.
 The dipole or the horn antenna, which acts as the receiver antenna at
its feed, receives this signal, to convert it into electric signal and
forwards it to the receiver circuitry.
 The following image shows a Parabolic Reflector Antenna.
 The gain of the paraboloid is a function of aperture ratio (D/λ).
 The Effective Radiated Power (ERP) of an antenna is the
multiplication of the input power fed to the antenna and its power gain.
 Usually a wave guide horn antenna is used as a feed radiator for the
paraboloid reflector antenna.
 Along with this technique, we have another type of feed given to the
paraboloid reflector antenna, called as Cassegrain feed.
 Cassegrain Feed

 Casse grain is another type of feed given to the reflector antenna.

 In this type, the feed is located at the vertex of the paraboloid, unlike in
the parabolic reflector.
 A convex shaped reflector, which acts as a hyperboloid is placed
opposite to the feed of the antenna. It is also known as secondary
hyperboloid reflector or sub-reflector.
 It is placed such that its one of the foci coincides with the focus of the
paraboloid.
 Thus, the wave gets reflected twice.
 Working of a Cassegrain Antenna

 When the antenna acts as a transmitting antenna, the energy from the
feed radiates through a horn antenna onto the hyperboloid concave
reflector, which again reflects back on to the parabolic reflector.
 he signal gets reflected into the space from there.
 Hence, wastage of power is controlled and the directivity gets
improved.
 When the same antenna is used for reception, the electromagnetic
waves strike the reflector, gets reflected on to the concave hyperboloid
and from there, it reaches to the feed.
 A wave guide horn antenna presents there to receive this signal and
sends to the receiver circuitry for amplification.
 Take a look at the following image.
 It shows a paraboloid reflector with cassegrain feed.
Advantages Disadvantage

 Reduction of minor lobes  Some of the power that gets

 Wastage of power is reduced reflected from the parabolic
 Equivalent focal length is
reflector is obstructed. This
achieved becomes a problem with small
dimension paraboloid.
 Feed can be placed in any
location, according to our
convenience
 Adjustment of beam
(narrowing or widening) is
done by adjusting the reflecting
surfaces
 Applications

 The following are the applications of Parabolic reflector antenna −

 The cassegrain feed parabolic reflector is mainly used in satellite
communications.
 Also used in wireless telecommunication systems.
 Gregorian Feed

 This is another type of feed used.

 A pair of certain configurations are there, where the feed beamwidth is
progressively increased while antenna dimensions are held fixed.
 Such a type of feed is known as Gregorian feed.
 Here, the convex shaped hyperboloid of casssegrain is replaced with a
concave shaped paraboloid reflector, which is of course, smaller in size
 These Gregorian feed type reflectors can be used in four ways −
 Gregorian systems using reflector ellipsoidal sub-reflector at foci F1.
 Gregorian systems using reflector ellipsoidal sub-reflector at foci F2.
 Cassegrain systems using hyperboloid sub-reflector (convex).
 Cassegrain systems using hyperboloid sub-reflector (concave but the feed
being very near to it.)
 These are all just to mention because they are not popular and are not
widely used. They have got their limitations.
 The figure clearly depicts the working pattern of all the types of
reflectors.
 There are other types of paraboloid Reflectors such as −
 Cut- paraboloid
 Parabolic cylinder
 Pill-box paraboloid
 However, all of them are seldom used because of the limitations and
disavantages they have in their working conditions.
 Hence, of all the types of reflector antennas, the simple parabolic
reflectors and the cassegrain feed parabolic reflectors are the most
commonly used ones.
 Folded Dipole Antenna / Aerial

 The folded dipole antenna or folded dipole aerial is

widely used, not only on its own, but also as the
driven element in other antennas like the Yagi
antenna and various other types of antenna.
 The folded dipole antenna consists of a basic dipole, but with an added
conductor connecting the two ends together. This makes a ‘loop’ of wire that is
a short circuit to DC. As the ends appear to be folded back, the antenna is called
a folded dipole antenna.
 Like the basic dipole, the folded dipole antenna is a balanced antenna, and
needs to be fed with a balanced feeder.
 The most common form of folded dipole is the half wave version. It is centre
fed in one of the lengths of wire. This means that it is fed where the current is at
a high level and the voltage is low.
 This means that like the standard half wave centre fed dipole it is fed at a low
impedance point, although the impedance is higher than that of the standard
half wave dipole.
 The additional part of the folded dipole antenna is often made by using a wire
or rod of the same diameter as the basic dipole section. However this is not
always the case.
 Also the wires or rods are typically equi-spaced along the length of the parallel
elements. This can be achieved in a number of ways.
 One of the main reasons for using a folded dipole
antenna is the increase in feed impedance that it
provides.
 If the conductors in the main dipole and the second
or "fold" conductor are the same diameter, then it is
found that there is a fourfold increase (i.e. two
squared) in the feed impedance.
 In free space, this gives an increase in feed
impedance from 73Ω to around 300Ω ohms.
Additionally the RF antenna has a wider bandwidth.
 Folded dipole impedance increase theory

 It is possible to reason why there is a four fold increase in impedance for the folded
dipole antenna.
 In a standard dipole antenna the currents flowing along the conductors are in phase
and as a result there is no cancellation of the fields and as a result radiation or the
signal occurs.
 When the second conductor is added to make the folded dipole antenna this can be
considered as an extension to the standard dipole with the ends folded back to meet
each other.
 As a result the currents in the new section flow in the same direction as those in the
original dipole. The currents along both the half-waves are therefore in phase and
the antenna will radiate with the same radiation patterns etc. as a simple half-wave
dipole.
 The impedance increase can be deduced from the fact that the power supplied to a
folded dipole antenna is evenly shared between the two sections which make up the
antenna.
 This means that when compared to a standard dipole the current in each conductor
is reduced to a half.
 As the same power is applied, the impedance has to be raised by a factor of four to
retain balance in the equation Watts = I2 x R.
 Folded dipole transmission line effect

 The folded element of the folded dipole antenna has a transmission line effect
attached with it.
 It can be viewed that the impedance of the dipole appears in parallel with the
impedance of the shorted transmission line sections, although the arguments for the
impedance given above still hold true - it is just another way of looking at the same
issue.
 This can help to explain some of the other properties of the antenna.
 The length is affected by this effect.
 Normally the wavelength of a standing wave in a feeder is affected by the velocity
factor.
 If air is used, this will by around 95% of the free space value.
 However if a flat feeder with a lower velocity factor is used, then this will have the
effect of shortening the required length.
 The feeder effect also results in the folded dipole antenna having a flatter response,
i.e. a wider bandwidth than a non-folded dipole.
 It occurs because at a frequency away from resonance, the reactance of the dipole is
of the opposite form from that of the sorted transmission line and as a result there is
some reactance cancellation at the feed point of the antenna.
 Folded dipole advantages

 There are two main advantages for using a folded dipole

antenna over a standard dipole:
 Increase in impedance:
 When higher impedance feeders need to be used, or when the
impedance of the dipole is reduced by factors such as parasitic
elements, a folded dipole provides a significant increase in
impedance level that enables the antenna to be matched more easily
to the feeder available.
 Wide bandwidth:
 The folded dipole antenna has a flatter frequency response - this
enables it to be used over a wider bandwidth with many
transmissions utilising a variety of different selectable channels, e.g.
television and broadcast radio, a wide bandwidth antenna is needed.
The standard dipole antenna does not always provide the required
bandwidth and the additional bandwidth of the folded dipole meets
the requirements .
 Unequal conductor folded dipoles

 On many occasions it can be necessary to implement impedance ratios

to the standard 4:1 ratio that is normal for a folded dipole antenna.
Simply by varying the effective diameter of the two conductors: top and
bottom, different ratios can be obtained.
 Multiconductor folded dipoles

 Although the concept of a folded dipole antenna often

implies the use of one extra conductor, the concept can
be extended further by adding additional conductors.
 This has the effect of increasing the overall impedance
even more and further widening the bandwidth.
 For the instance for a three wire folded dipole, with all
wires or conductors having he same diameter, the
impedance is increased by a factor of three squared, i.e.
9.
 This means that the nominal value for a folded dipole
with three conductors is 9 times 73Ω or approximately
600Ω
 Folded dipole applications

 There are very many situations in which folded dipoles can be used. Their properties
of a higher feed impedance than the straight centre fed half wave dipole and
increased bandwidth provide an essential performance improvement required for
many antenna systems.
 There are several situations in which folded dipoles are used:
 On their own: Folded dipole antennas are sometimes used on their own, but they
must be fed with a high impedance feeder, typically 300 ohms. This on its own can
be very useful in certain applications where balanced feeders may be used.
 As part of another antenna: Folded dipoles find more uses when a dipole is
incorporated in another RF antenna design with other elements nearby. The issue is
that incorporating a dipole into an antenna such as a Yagi where elements are
closely coupled reduces the feed impedance. If a simple dipole was used, then the
feed impedance levels of less than 20 Ω or less can easily be experienced.
 Using a folded dipole enables the impedance to be increased by a factor of four or
whatever is required by having multiple wires in the folded dipole.
 Increased bandwidth: Sometimes folded dipoles may be employed purely to
give a greater bandwidth. When used to increase bandwidth, folded dipoles may be
used on their own or within another antenna system.
 Log-periodic antenna

 The Yagi-Uda antenna is mostly used for domestic

purpose.
 However, for commercial purpose and to tune over a
range of frequencies, we need to have another
antenna known as the Log-periodic antenna.
 A Log-periodic antenna is that whose impedance is a
logarithamically periodic function of frequency.
 The frequency range, in which the log-periodic
antennas operate is around 30 MHz to
3GHz which belong to the VHF and UHF bands.
Construction & Working of Log-periodic Antenna

 The construction and operation of a log-periodic

antenna is similar to that of a Yagi-Uda antenna.
 The main advantage of this antenna is that it exhibits
constant characteristics over a desired frequency
range of operation.
 It has the same radiation resistance and therefore
the same SWR.
 The gain and front-to-back ratio are also the same.
 With the change in operation frequency, the active
region shifts among the elements and hence all the
elements will not be active only on a single
frequency. This is its special characteristic.
 There are several type of log-periodic antennas such
as the planar, trapezoidal, zig-zag, V-type, slot and
the dipole.
 The mostly used one is log-periodic dipole array, in
short, LPDA.
 The diagram of log-periodic array is given above.
 The physical structure and electrical characteristics,
when observed, are repetitive in nature.
 The array consists of dipoles of different lengths and
spacing, which are fed from a two-wire transmission
line.
 This line is transposed between each adjacent pair of
dipoles.
 The dipole lengths and seperations are related by the
formula −
R1R2=R2R3=R3R4=T=l1l2=l2l3=l3l4
Where
 т is the design ratio and т<1
 R is the distance between the feed and the dipole
 l is the length of the dipole.
 The directive gains obtained are low to moderate.
 The radiational patterns may be Unidirectional or
Bi-directional.
 Radiation Pattern

 The Radiation pattern of log-periodic antenna can be

of uni-directional or bi-directional, depending upon
the log periodic structures.
 For uni-directional Log-periodic antenna, the
radiation towards shorter element is of considerable
amount, whereas in forward direction, it is small or
zero.
 The radiational pattern for uni-directional log-
periodic antenna is given above.
 For bi-directional Log-periodic antenna, the
maximum radiation is in broad side, which is normal
to the surface of the antenna.

 The figure given above shows the radiational pattern

for a bi-directional log-periodic antenna.
Advantages Disadvantages

 The following are the  The following are the

advantages of Log- disadvantages of Log-
periodic antennas − periodic antennas −
 The antenna design is
 External mount.
compact.
 Installation cost is
 Gain and radiation
pattern are varied high.
according to the
requirements.
 Applications

 The following are the applications of Log-periodic

antennas −
 Used for HF communications.
 Used for particular sort of TV receptions.
 Used for all round monitoring in higher frequency
bands.
 Micro strip antennas

 Micro strip antennas are low-profile antennas.

 A metal patch mounted at a ground level with a di-
electric material in-between constitutes a Micro
strip or Patch Antenna.
 These are very low size antennas having low
radiation.
 The patch antennas are popular for low profile
applications at frequencies above 100MHz.
Construction & Working of Micro strip Antennas

 Micro strip antenna consists of a very thin

metallic strip placed on a ground plane with a di-
electric material in-between.
 The radiating element and feed lines are placed by
the process of photo-etching on the di-electric
material.
 Usually, the patch or micro-strip is choosen to be
square, circular or rectangular in shape for the ease
of analysis and fabrication.
 The following image shows a micro-strip or patch
antenna.
 The length of the metal patch is λ/2. When the
antenna is excited, the waves generated within the
di-electric undergo reflections and the energyis
radiated from the edges of the metal patch,which is
very low.
 Radiation Pattern

 The radiation pattern of microstrip or patch antenna

is broad. It has low radiation power and narrow
frequency bandwidth.
 The radiation pattern of a microstrip or patch
antenna is shown above. It has lesser directivity. To
have a greater directivity, an array can be formed by
using these patch antennas.
Advantages Disadvantages

 The following are the  The following are the

advantages of Micro disadvantages of Micro
strip antenna − strip antenna −
 Lighteweight  Inefficient radiation
 Low cost  Narrow frequency
 Ease of installation bandwidth
 Applications

 The following are the applications of Micro strip

antenna −
 Used in Space craft applications
 Used in Air craft applications
 Used in Low profile antenna applications