IEEE & IEC STANDARDS

Sr. No Standard Reference Description

POWER SYSTEM DESIGN AND ANALYSIS

1 399 - 1997( Brown Book ) IEEE recommended practise for Industrial & Commercial power system analysis ( Industrial and Commercial
Facilities )
2 551 - 2006 ( Voilet Book ) IEEE recommended practise for Calculating Short circuit current in Industrial and Commercial Power System (
Industrial and Commercial Facilities )
3 605 - 1998 IEEE Guide for design of Substation rigid - bus structures ( Power Substations )
4 738 - 2006 IEEE Standard for Calculating the Current Temparature of Bare Overhead Conductors ( Power Transmission &
Distribution )
5 835 -1994 IEEE Standard Power cable Ampacity Table ( Insulated Conductors )
6 837 - 2002 IEEE Standard for qualifying permanent connections used in substation Grounding ( Power Substations )

7 848 - 1996 IEEE Standard Procedure for the Determiantion of Ampacity , Derating of Fire Protected cables ( Insulated
Condictors )
8 1127 - 1998 IEEE guide for the Design, construction & operation of eleectric power substations for community acceptance
and environmental compatability (Power substations )
9 1189 - 1996 IEEE guide for selection of Valve - Regulated Lead - Acid ( VRLA) batteries for station Applicatios ( Energy
Devolopment & Power Generation )
10 IEC - 60865-1 (1993-10) Short Circuit Currents - Caculation of Effects Part 1 - Defenitions and Calculation Methods
11 IEC - 60865-2 (1994-06) Short Circuit Currents - Caculation of Effects Part 2 - Examples of Calculations
12 IEC - 60909-0 (2001-07) Short Circtuit Currents in 3 Phase AC Systems Part 0 - Caculation of Currents
POWER GENERATION & DISTRIBUTION SYSTEM
13 141 - 1993 ( Red Book ) IEE recommended practise for Electric Power Distribution for Power plants ( Industrial and Commercial
Facilities )
14 242 - 2001 ( Buf Book ) IEE recommended practise for Protection and Coordination of Industrial and Commercial Power Systems (
Industrial and Commercial Facilities )
15 367 - 1996 IEE recommended practise for determining the Electric Power station ground potential rise and induced voltage
from a power fault ( Communications , Power System Communications )
1 of 48
Sr. No Standard Reference Description

16 643 - 2004 IEE Guide for Power - Line Carrier Applications ( Power System Communications )
17 665 - 1995 IEE Guide for generating station Grounding [ Energy Devolopment / Power Generation ]
18 979 - 1994 IEEE guide for Substation Fire Protection (Power substations )
19 1050 - 2004 IEEE guide for Instrumentation & Control Equipment Grounding I Generating stations ( Energr Development &
Power Generation )
20 1185 - 1994 IEEE guide for installation methods for generating station cables ( Insulated conductors )
21 487 - 2000 IEE recommended practise for the protestion of wire-line communication facilities serving electric supply
locations ( Power System Communications )
22 524 - 2003 IEE Guide to the Installation of Overhead transmission line conductors ( Power Transmission & Distribution )

23 951 - 1996 IEEE guide to Assembly & Erection of metal Transmission structures ( Power Transmission & Distribution )

24 977 - 1991 IEEE guide to Installation of Foundation for Transmission Line Structures ( Power Transmission & Distribution
)
25 979 - 1994 IEEE guide for Substation Fire Protection (Power substations )
26 1050 - 2004 IEEE guide for Instrumentation & Control Equipment Grounding I Generating stations ( Energr Development &
Power Generation )
27 1300- 1996 IEEE guide for cable connections for Gas - Insulated Substations ( Insulated conductors )
28 1441 - 2004 IEEE guide for Inspection of Overhead Transmission line construction ( Power Transmission & Distribution )

29 C37.104 - 2002 IEEE guide for automatic reclosing of line circuit breakers for AC distribution and Transmission Lines (
Protective Relaying )
30 C37.113 - 1999 IEEE guide for protective Relay Applications to Transmission Lines ( Protective Relaying )
31 C37.114 - 2004 IEEE guide for Determining Fault Location on AC Transmission and Dstribution Lines ( Protective Relaying )

EQUIPMENTS
32 484 - 2002 IEE recommended practise for Installation Design and Installation of Vented Lead Acid Batteries for Stationary
Applications [ Energy Devolopment / Power Generation Nuclear Engineering ]
33 485 - 1997 IEE recommended practise for sizing Lead Acid Batteries for Stationary applications [ Energy Devolopment /
Power Generation Nuclear Engineering ]
2 of 48
Sr. No Standard Reference Description

POWER SYSTEM PROTECTION

34 C37 - 91 - 2000 IEEE guide for protective Relay Application to Power Transformers ( Protective Relaying )
35 C37.96 - 2000 IEEE guide for AC Motor Protection ( Protective Relaying )
36 C37.97 - 1979 IEEE guide for protective Relay Application to Power System Buses ( Protective Relaying )
37 C37.101 - 1993 IEEE guide for Generator Ground Protection ( Protective Relaying )
38 C37.102 - 2006 IEEE guide for AC Generator Protection ( Protective Relaying )
39 C37.106 - 2003 IEEE guide for Abnormal Frequency Protection for power generating plants ( Protective Relaying )
GIS
40 C37.122 - 1993 IEEE standard for Gas Insulated Substations ( Power Substations )
41 C37.123 - 1996 IEEE guide to specifications for gas - insulated , electric power substation equipment ( Power Substations )

TESTING
42 4 - 1995 IEE Standard Techniques for High Voltage Testing ( Testing , Instrumentation & Measurement, and Metric
Practise )
43 4a - 2001 Amendment to IEE Standard Techniques for High Voltage Testing ( Testing , Instrumentation & Measurement,
and Metric Practise )
44 43 - 2000 IEE recommended practise for Testing Insulation Resistance of rotating machinery ( Electric Machinery )

45 48 - 1996 IEE Standard Test Procedures and requirements for Alternating Current cable terminations 2.5 KV through 756
KV [Insulated conductors]
46 62 - 1995 IEE Guide for diagnostic field testing of electric power apparatus . Part 1 : Oil filled Power Transformers,
Regulators and Reactors [ Power Transformers (Distribution & Regulating) Testing , Instrumentation &
Measurement, and Metric Practise ]
47 81 - 1983 IEE Guide for measuring earth resistivity , ground impedance and earth surface potentials of Grounding
system ( Testing , Instrumentation & Measurement, and Metric Practise )
48 82 - 2002 IEE Standard Test Procedure for Impulse Voltage Test on insulated conductors
49 450 - 2002 IEE recommended practise for maintanance , Testing and replacement of Vented Lead Acid Batteries for
Stationary Applications [ Energy Devolopment / Power Generation ]
50 576 - 2000 IEE recommended practise for installatiion , termination & testing ofInsulated Power cables as used in
Industrial and Commercial Power System ( Industrial and Commercial Facilities )
3 of 48
Sr. No Standard Reference Description

51 691 - 2001 IEE Guide for Transmission Structure Foundation Design and Testing ( Power Transmission & Distribution )

52 1125 - 1993 IEEE guide for moisture measurement and control in SF / sub 6/Gas- Insulated Equipment
53 1291 - 1993 IEEE guide for partial discharge measurement in power switchgear ( Power Switchgear , Circuits & Fuses )
54 C37.34 - 1994 IEEE std test code for high - voltage Air Switches ( Power Switchgear , Circuits & Fuses )
55 C37.103 - 2004 IEEE guide for Differential & Polarising Relay curcuit Testing ( Protective Relaying )
56 C57.12.91 - 2001 IEEE std test code for dry - type distribution & power transformers [ Power Transformers ( Distribution &
Regulating ) ]
57 C57.19.00 - 2004 IEEE Standard General Requirement & Test Procedure for Power apparatus Bushings [ Power Transformers (
Distribution & Regulating ) ]
58 C57.113 - 1991 IEEE guide for partial Discharge measurement in Liquid - filled Power Transformers and shunt reactors ( Power
Switchgear , Circuits & Fuses )
59 C135.61 - 1997 IEEE Standard for the testing of Overhead Transmission & Distribution line Hardware ( Power Transmission &
Distribution )
POWER TRANSMISSION SYSTEM
60 487 - 2000 IEE recommended practise for the protestion of wire-line communication facilities serving electric supply
locations ( Power System Communications )
61 524 - 2003 IEE Guide to the Installation of Overhead transmission line conductors ( Power Transmission & Distribution )

62 951 - 1996 IEEE guide to Assembly & Erection of metal Transmission structures ( Power Transmission & Distribution )
63 977 - 1991 IEEE guide to Installation of Foundation for Transmission Line Structures ( Power Transmission & Distribution
)
64 979 - 1994 IEEE guide for Substation Fire Protection (Power substations )
65 1050 - 2004 IEEE guide for Instrumentation & Control Equipment Grounding I Generating stations ( Energr Development &
Power Generation )
66 1300- 1996 IEEE guide for cable connections for Gas - Insulated Substations ( Insulated conductors )
67 1441 - 2004 IEEE guide for Inspection of Overhead Transmission line construction ( Power Transmission & Distribution )

4 of 48
Sr. No Standard Reference Description

68 C37.104 - 2002 IEEE guide for automatic reclosing of line circuit breakers for AC distribution and Transmission Lines (
Protective Relaying )
69 C37.113 - 1999 IEEE guide for protective Relay Applications to Transmission Lines ( Protective Relaying )
70 C37.114 - 2004 IEEE guide for Determining Fault Location on AC Transmission and Dstribution Lines ( Protective Relaying )
71 IEC - 60050-466 International Electrotechnical Vocabulary - Overhead lines
72 IEC - 60652 (2002-06) Loading Tests on Overhead line structures
73 IEC - 60826 (2003-10) Design Criteria for Overhead Transmission line
74 IEC - 61773-2 (1996-11) Overhead Lines - Testing of Foundation for Structures
75 C37.114 - 2004 IEEE guide for Determining Fault Location on AC Transmission and Dstribution Lines ( Protective Relaying )

Total of the available costs

ESTIMATED TOTAL COST

5 of 48
Cost in SAR

500.00

285.00

285.00

6 of 48
Cost in SAR

245.00
0.00
315.00

345.00

410.00

525.00

315.00

415.00

400.00
245.00

3,215.00

7 of 48
Cost in SAR

0.00
385.00

315.00
435.00

285.00
1,420.00
570.00
400.00

970.00

8 of 48
Cost in SAR

345.00

340.00

370.00

1,055.00

345.00

410.00
525.00

315.00

9 of 48
Cost in SAR

415.00

400.00
245.00

245.00

6,945.00

20,000.00

10 of 48
 IEEE STANDARDS
http://eeexplore.ieee.o

Standard
Sr. No Description Cost in SAR
Reference
1 4 - 1995 IEE Standard Techniques for High Voltage Testing ( Testing , Instrumentation & Measurement,
and Metric Practise )
2 4a - 2001 Amendment to IEE Standard Techniques for High Voltage Testing ( Testing , Instrumentation &
Measurement, and Metric Practise )
3 43 - 2000 IEE recommended practise for Testing Insulation Resistance of rotating machinery ( Electric
Machinery )
4 48 - 1996 IEE Standard Test Procedures and requirements for Alternating Current cable terminations 2.5 KV
through 756 KV [Insulated conductors]
5 62 - 1995 IEE Guide for diagnostic field testing of electric power apparatus . Part 1 : Oil filled Power
Transformers, Regulators and Reactors [ Power Transformers (Distribution & Regulating) Testing
, Instrumentation & Measurement, and Metric Practise ]
6 81 - 1983 IEE Guide for measuring earth resistivity , ground impedance and earth surface potentials of
Grounding system ( Testing , Instrumentation & Measurement, and Metric Practise )

7 82 - 2002 IEE Standard Test Procedure for Impulse Voltage Test on insulated conductors
8 141 - 1993 ( Red Book IEE recommended practise for Electric Power Distribution for Power plants ( Industrial and
) Commercial Facilities )
9 242 - 2001 ( Buf IEE recommended practise for Protection and Coordination of Industrial and Commercial Power
Book ) Systems ( Industrial and Commercial Facilities )
10 367 - 1996 IEE recommended practise for determining the Electric Power station ground potential rise and
induced voltage from a power fault ( Communications , Power System Communications )

11 386 - 2006 IEE Standard for Seperable Insulated connected system for Power Distribution Systems Above
600 V ( Insulated conductors Power Transmission & Distribution )
12 399 - 1997( Brown IEE recommended practise for Industrial & Commercial power system analysis ( Industrial and
Book ) Commercial Facilities )
13 400.3 - 2006 IEE Guide for Partial Discharge testing of Shielded power cable Systems in a field Environment (
Insulated Conductors Nuclear Engineering )
11 of 48
 Standard
Sr. No Description Cost in SAR
Reference
14 450 - 2002 IEE recommended practise for maintanance , Testing and replacement of Vented Lead Acid
Batteries for Stationary Applications [ Energy Devolopment / Power Generation ]
15 484 - 2002 IEE recommended practise for Installation Design and Installation of Vented Lead Acid Batteries
for Stationary Applications [ Energy Devolopment / Power Generation Nuclear Engineering ]

16 485 - 1997 IEE recommended practise for sizing Lead Acid Batteries for Stationary applications [ Energy
Devolopment / Power Generation Nuclear Engineering ]
17 487 - 2000 IEE recommended practise for the protestion of wire-line communication facilities serving electric
supply locations ( Power System Communications )
18 524 - 2003 IEE Guide to the Installation of Overhead transmission line conductors ( Power Transmission & 345.00
Distribution )
19 551 - 2006 ( Voilet IEE recommended practise for Calculating Short circuit current in Industrial and Commercial
Book ) Power System ( Industrial and Commercial Facilities )
20 576 - 2000 IEE recommended practise for installatiion , termination & testing ofInsulated Power cables as
used in Industrial and Commercial Power System ( Industrial and Commercial Facilities )

21 605 - 1998 IEE Guide for design of Substation rigid - bus structures ( Power Substations ) 500.00
22 637 - 1985 IEE Guide for the reclamation of Insulating Oil and criteria of it's use [ Power Transformers
(Distribution & Regulating) ]
23 643 - 2004 IEE Guide for Power - Line Carrier Applications ( Power System Communications ) 245.00

24 665 - 1995 IEE Guide for generating station Grounding [ Energy Devolopment / Power Generation ]

25 691 - 2001 IEE Guide for Transmission Structure Foundation Design and Testing ( Power Transmission & 345.00
Distribution )
26 738 - 2006 IEE Standard for Calculating the Current Temparature of Bare Overhead Conductors ( Power
Transmission & Distribution )
27 835 -1994 IEEE Standard Power cable Ampacity Table ( Insulated Conductors )
28 837 - 2002 IEEE Standard for qualifying permanent connections used in substation Grounding ( Power 285.00
Substations )

12 of 48
 Standard
Sr. No Description Cost in SAR
Reference
29 848 - 1996 IEEE Standard Procedure for the Determiantion of Ampacity , Derating of Fire Protected cables (
Insulated Condictors )
30 951 - 1996 IEEE guide to Assembly & Erection of metal Transmission structures ( Power Transmission & 410.00
Distribution )
31 977 - 1991 IEEE guide to Installation of Foundation for Transmission Line Structures ( Power Transmission & 525.00
Distribution )
32 979 - 1994 IEEE guide for Substation Fire Protection (Power substations ) 315.00

33 1050 - 2004 IEEE guide for Instrumentation & Control Equipment Grounding I Generating stations ( Energr
Development & Power Generation )
34 1125 - 1993 IEEE guide for moisture measurement and control in SF / sub 6/Gas- Insulated Equipment

35 1127 - 1998 IEEE guide for the Design, construction & operation of eleectric power substations for community
acceptance and environmental compatability (Power substations )
36 1185 - 1994 IEEE guide for installation methods for generating station cables ( Insulated conductors )

37 1189 - 1996 IEEE guide for selection of Valve - Regulated Lead - Acid ( VRLA) batteries for station Applicatios
( Energy Devolopment & Power Generation )
38 1291 - 1993 IEEE guide for partial discharge measurement in power switchgear ( Power Switchgear , Circuits
& Fuses )
39 1300- 1996 IEEE guide for cable connections for Gas - Insulated Substations ( Insulated conductors )

40 1441 - 2004 IEEE guide for Inspection of Overhead Transmission line construction ( Power Transmission &
Distribution )
41 C2 - 2007 National Electric Safety Code 2007 Edition [ National Electric Safety Code ( NESC ) ]
42 C37 - 91 - 2000 IEEE guide for protective Relay Application to Power Transformers ( Protective Relaying ) 385.00

43 C37.34 - 1994 IEEE std test code for high - voltage Air Switches ( Power Switchgear , Circuits & Fuses )
44 C37.96 - 2000 IEEE guide for AC Motor Protection ( Protective Relaying )

13 of 48
 Standard
Sr. No Description Cost in SAR
Reference
45 C37.97 - 1979 IEEE guide for protective Relay Application to Power System Buses ( Protective Relaying ) 315.00

46 C37.101 - 1993 IEEE guide for Generator Ground Protection ( Protective Relaying ) 435.00
47 C37.102 - 2006 IEEE guide for AC Generator Protection ( Protective Relaying )
48 C37.103 - 2004 IEEE guide for Differential & Polarising Relay curcuit Testing ( Protective Relaying ) 340.00
49 C37.104 - 2002 IEEE guide for automatic reclosing of line circuit breakers for AC distribution and Transmission 415.00
Lines ( Protective Relaying )
50 C37.106 - 2003 IEEE guide for Abnormal Frequency Protection for power generating plants ( Protective Relaying ) 285.00

51 C37.110 - 1996 IEEE guide for the Application of Current Transformer used for Protective Relaying Purposes ( 435.00
Protective Relaying )
52 C37.112 - 1996 IEEE standard inverse - time charcteristics equations for over current relays ( Protective Relaying 375.00
)
53 C37.113 - 1999 IEEE guide for protective Relay Applications to Transmission Lines ( Protective Relaying ) 400.00

54 C37.114 - 2004 IEEE guide for Determining Fault Location on AC Transmission and Dstribution Lines ( Protective 245.00
Relaying )
55 C37.122 - 1993 IEEE standard for Gas Insulated Substations ( Power Substations ) 570.00
56 C37.123 - 1996 IEEE guide to specifications for gas - insulated , electric power substation equipment ( Power 400.00
Substations )
57 C57.12.91 - 2001 IEEE std test code for dry - type distribution & power transformers [ Power Transformers (
Distribution & Regulating ) ]
58 C57.13 - 1993 IEEE std requirements for instrument transformers [ Power Transformers ( Distribution &
Regulating ) ]
59 C57.19.00 - 2004 IEEE Standard General Requirement & Test Procedure for Power apparatus Bushings [ Power
Transformers ( Distribution & Regulating ) ]
60 C57.93 - 1995 IEEE guide for Installation of Liquid Immersed Power Transformers [ Power Transformers (
Distribution & Regulating ) ]
61 C57.113 - 1991 IEEE guide for partial Discharge measurement in Liquid - filled Power Transformers and shunt
reactors ( Power Switchgear , Circuits & Fuses )
14 of 48
 Standard
Sr. No Description Cost in SAR
Reference
62 C135.61 - 1997 IEEE Standard for the testing of Overhead Transmission & Distribution line Hardware ( Power 370.00
Transmission & Distribution )
Total 7,940.00

15 of 48
IEEE STANDARDS
http://eeexplore.ieee.org

Remarks

Testing

Testing

Testing

Testing

Testing

Testing

Testing
Power Gen. & Dist.
System
Power Gen. & Dist.
System
Power Gen. & Dist.
System

Power System Analysis

16 of 48
 Remarks

Testing

Equipments

Equipments

Power Transmission
system
Power Transmission
system
Design

Testing

Design
Equipments

Power Gen. & Dist.

System
Power Gen. & Dist.
System
Testing

Design

Design
Design

17 of 48
 Remarks

Design

Power Transmission
system
Power Transmission
system
Power Gen. & Dist.
System
Power Gen. & Dist.
System
Testing

Design

Power Gen. & Dist.

System
Design

Testing

Power Transmission
system
Power Transmission
system
e
Protection

Testing
Protection

18 of 48
 Remarks

Protection

Protection
Protection
Testing
Power Transmission
system
Protection

Power Transmission
system
Power Transmission
system
GIS
GIS

Testing

Testing

Testing

19 of 48
Remarks

Testing

20 of 48
 IEEE STANDARDS

Standard
Sr. No
Reference
1 4 - 1995

2 4a - 2001

3 43 - 2000

4 48 - 1996

5 62 - 1995

6 81 - 1983

7 82 - 2002
14 450 - 2002

20 576 - 2000

25 691 - 2001

34 1125 - 1993

38 1291 - 1993

43 C37.34 - 1994
48 C37.103 - 2004
57 C57.12.91 - 2001

58 C57.13 - 1993

59 C57.19.00 - 2004
60 C57.93 - 1995

61 C57.113 - 1991

62 C135.61 - 1997
 IEEE STANDARDS
http://eeexplore.ie

Description Cost in SAR

IEE Standard Techniques for High Voltage Testing ( Testing , Instrumentation & Measurement,
and Metric Practise )
Amendment to IEE Standard Techniques for High Voltage Testing ( Testing , Instrumentation &
Measurement, and Metric Practise )
IEE recommended practise for Testing Insulation Resistance of rotating machinery ( Electric
Machinery )
IEE Standard Test Procedures and requirements for Alternating Current cable terminations 2.5 KV
through 756 KV [Insulated conductors]
IEE Guide for diagnostic field testing of electric power apparatus . Part 1 : Oil filled Power
Transformers, Regulators and Reactors [ Power Transformers (Distribution & Regulating) Testing
, Instrumentation & Measurement, and Metric Practise ]
IEE Guide for measuring earth resistivity , ground impedance and earth surface potentials of
Grounding system ( Testing , Instrumentation & Measurement, and Metric Practise )

IEE Standard Test Procedure for Impulse Voltage Test on insulated conductors
IEE recommended practise for maintanance , Testing and replacement of Vented Lead Acid
Batteries for Stationary Applications [ Energy Devolopment / Power Generation ]
IEE recommended practise for installatiion , termination & testing ofInsulated Power cables as
used in Industrial and Commercial Power System ( Industrial and Commercial Facilities )

IEE Guide for Transmission Structure Foundation Design and Testing ( Power Transmission & 345.00
Distribution )
IEEE guide for moisture measurement and control in SF / sub 6/Gas- Insulated Equipment

IEEE guide for partial discharge measurement in power switchgear ( Power Switchgear , Circuits
& Fuses )
IEEE std test code for high - voltage Air Switches ( Power Switchgear , Circuits & Fuses )
IEEE guide for Differential & Polarising Relay curcuit Testing ( Protective Relaying ) 340.00
IEEE std test code for dry - type distribution & power transformers [ Power Transformers (
Distribution & Regulating ) ]
IEEE std requirements for instrument transformers [ Power Transformers ( Distribution &
Regulating ) ]
IEEE Standard General Requirement & Test Procedure for Power apparatus Bushings [ Power
Transformers ( Distribution & Regulating ) ]
IEEE guide for Installation of Liquid Immersed Power Transformers [ Power Transformers (
Distribution & Regulating ) ]
IEEE guide for partial Discharge measurement in Liquid - filled Power Transformers and shunt
reactors ( Power Switchgear , Circuits & Fuses )
IEEE Standard for the testing of Overhead Transmission & Distribution line Hardware ( Power 370.00
Transmission & Distribution )
Total 1,055.00
http://eeexplore.ieee.org

Remarks

Testing

Testing

Testing

Testing

Testing

Testing

Testing
Testing

Testing

Testing

Testing

Testing

Testing
Testing
Testing

Testing
Testing

Testing
 IEEE STANDARDS

Standard
Sr. No
Reference
8 141 - 1993 ( Red Book
)
9 242 - 2001 ( Buf
Book )
10 367 - 1996

23 643 - 2004

24 665 - 1995

32 979 - 1994

33 1050 - 2004

36 1185 - 1994
 IEEE STANDARDS
http://eeexplore.ie

Description Cost in SAR

IEE recommended practise for Electric Power Distribution for Power plants ( Industrial and
Commercial Facilities )
IEE recommended practise for Protection and Coordination of Industrial and Commercial Power
Systems ( Industrial and Commercial Facilities )
IEE recommended practise for determining the Electric Power station ground potential rise and
induced voltage from a power fault ( Communications , Power System Communications )

IEE Guide for Power - Line Carrier Applications ( Power System Communications ) 245.00

IEE Guide for generating station Grounding [ Energy Devolopment / Power Generation ]

IEEE guide for Substation Fire Protection (Power substations ) 315.00

IEEE guide for Instrumentation & Control Equipment Grounding I Generating stations ( Energr
Development & Power Generation )
IEEE guide for installation methods for generating station cables ( Insulated conductors )

Total 560.00
http://eeexplore.ieee.org

Remarks

Power Gen. & Dist.

System
Power Gen. & Dist.
System
Power Gen. & Dist.
System

Power Gen. & Dist.

System
Power Gen. & Dist.
System
Power Gen. & Dist.
System
Power Gen. & Dist.
System
Power Gen. & Dist.
System
 IEEE STANDARDS

Standard
Sr. No
Reference
12 399 - 1997( Brown
Book )
 IEEE STANDARDS
http://eeexplore.ie

Description Cost in SAR

IEE recommended practise for Industrial & Commercial power system analysis ( Industrial and
Commercial Facilities )
http://eeexplore.ieee.org

Remarks

Power System Analysis

 IEEE STANDARDS

Standard
Sr. No
Reference
15 484 - 2002

16 485 - 1997
 IEEE STANDARDS
http://eeexplore.ie

Description Cost in SAR

IEE recommended practise for Installation Design and Installation of Vented Lead Acid Batteries
for Stationary Applications [ Energy Devolopment / Power Generation Nuclear Engineering ]

IEE recommended practise for sizing Lead Acid Batteries for Stationary applications [ Energy
Devolopment / Power Generation Nuclear Engineering ]
Total 0.00
http://eeexplore.ieee.org

Remarks

Equipments

Equipments
 IEEE STANDARDS

Standard
Sr. No
Reference
17 487 - 2000

18 524 - 2003

30 951 - 1996

31 977 - 1991

32 979 - 1994

33 1050 - 2004

39 1300- 1996

40 1441 - 2004

49 C37.104 - 2002

53 C37.113 - 1999

54 C37.114 - 2004
 IEEE STANDARDS
http://eeexplore.ie

Description Cost in SAR

IEE recommended practise for the protestion of wire-line communication facilities serving electric
supply locations ( Power System Communications )
IEE Guide to the Installation of Overhead transmission line conductors ( Power Transmission & 345.00
Distribution )
IEEE guide to Assembly & Erection of metal Transmission structures ( Power Transmission & 410.00
Distribution )
IEEE guide to Installation of Foundation for Transmission Line Structures ( Power Transmission & 525.00
Distribution )
IEEE guide for Substation Fire Protection (Power substations ) 315.00

IEEE guide for Instrumentation & Control Equipment Grounding I Generating stations ( Energr
Development & Power Generation )
IEEE guide for cable connections for Gas - Insulated Substations ( Insulated conductors )

IEEE guide for Inspection of Overhead Transmission line construction ( Power Transmission &
Distribution )
IEEE guide for automatic reclosing of line circuit breakers for AC distribution and Transmission 415.00
Lines ( Protective Relaying )
IEEE guide for protective Relay Applications to Transmission Lines ( Protective Relaying ) 400.00

IEEE guide for Determining Fault Location on AC Transmission and Dstribution Lines ( Protective 245.00
Relaying )
Total 2,655.00
http://eeexplore.ieee.org

Remarks

Power Transmission
system
Power Transmission
system
Power Transmission
system
Power Transmission
system
Power Gen. & Dist.
System
Power Gen. & Dist.
System
Power Transmission
system
Power Transmission
system
Power Transmission
system
Power Transmission
system
Power Transmission
system
 IEEE STANDARDS

Standard
Sr. No
Reference
19 551 - 2006 ( Voilet
Book )
21 605 - 1998
26 738 - 2006

27 835 -1994
28 837 - 2002

29 848 - 1996

35 1127 - 1998

37 1189 - 1996
 IEEE STANDARDS
http://eeexplore.ie

Description Cost in SAR

IEE recommended practise for Calculating Short circuit current in Industrial and Commercial
Power System ( Industrial and Commercial Facilities )
IEE Guide for design of Substation rigid - bus structures ( Power Substations ) 500.00
IEE Standard for Calculating the Current Temparature of Bare Overhead Conductors ( Power
Transmission & Distribution )
IEEE Standard Power cable Ampacity Table ( Insulated Conductors )
IEEE Standard for qualifying permanent connections used in substation Grounding ( Power 285.00
Substations )
IEEE Standard Procedure for the Determiantion of Ampacity , Derating of Fire Protected cables (
Insulated Condictors )
IEEE guide for the Design, construction & operation of eleectric power substations for community
acceptance and environmental compatability (Power substations )
IEEE guide for selection of Valve - Regulated Lead - Acid ( VRLA) batteries for station Applicatios
( Energy Devolopment & Power Generation )
Total 785.00
http://eeexplore.ieee.org

Remarks

Design

Design
Design

Design
Design

Design

Design

Design
 IEEE STANDARDS

Standard
Sr. No
Reference
42 C37 - 91 - 2000

44 C37.96 - 2000
45 C37.97 - 1979

46 C37.101 - 1993
47 C37.102 - 2006
50 C37.106 - 2003

55 C37.122 - 1993
56 C37.123 - 1996
 IEEE STANDARDS
http://eeexplore.ie

Description Cost in SAR

IEEE guide for protective Relay Application to Power Transformers ( Protective Relaying ) 385.00

IEEE guide for AC Motor Protection ( Protective Relaying )

IEEE guide for protective Relay Application to Power System Buses ( Protective Relaying ) 315.00

IEEE guide for Generator Ground Protection ( Protective Relaying ) 435.00

IEEE guide for AC Generator Protection ( Protective Relaying )
IEEE guide for Abnormal Frequency Protection for power generating plants ( Protective Relaying ) 285.00

IEEE standard for Gas Insulated Substations ( Power Substations ) 570.00

IEEE guide to specifications for gas - insulated , electric power substation equipment ( Power 400.00
Substations )
Total 2,390.00
http://eeexplore.ieee.org

Remarks

Protection

Protection
Protection

Protection
Protection
Protection

GIS
GIS
 IEC STANDARDS

Sr.
Standard Reference Description
No
1 IEC - 60050-466 International Electrotechnical Vocabulary - Overhead lines
2 IEC - 60652 (2002-06) Loading Tests on Overhead line structures
3 IEC - 60826 (2003-10) Design Criteria for Overhead Transmission line
4 IEC - 61773-2 (1996-11) Overhead Lines - Testing of Foundation for Structures
5 IEC - 60865-1 (1993-10) Short Circuit Currents - Caculation of Effects Part 1 - Defenitions and Calculation Methods
6 IEC - 60865-2 (1994-06) Short Circuit Currents - Caculation of Effects Part 2 - Examples of Calculations
7 IEC - 60909-0 (2001-07) Short Circtuit Currents in 3 Phase AC Systems Part 0 - Caculation of Currents
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
STANDARDS

Cost Remarks