Design of Ee cuiCuls For V Semester B.E. 4 | As per the New Syllabus of VTU fe J.B.K. Das = ff MSU sat ateDas. ‘WOH =. 10130633Design of Machine Elements - 1 - For V Semester 8.£. Studerts, by Prof. J.B.K. Das and PL. Srinivasa Murthy published by Sapna Book House (P) Ltd., R.O. #11, 3% Main Road, Ganchinagar, Bengaluru 560009 Ph: 080-40114455 (Engg., 71) ISBN : 81-280-0237-6 © Avthors NOTICE OF CAUTION Foproduation Rights : "No par of this publication which Is material protected by this copyright tice may be reproduced or transmitted or utlized of stored in any form or by any means now known oF herennatter invented, electronic, digital or mechanical, including photocopying. scanring, recording or by any information storage or retrieval system, without prior written permission trom the pubisher’. Photocopying and Resale Prohibition : “Copying of the book ard seling it after photocopying oF oselling @ as second hend 00‘ is ilogel and is not allowed, under the copyright act. ‘Ths book ie sold subject to the condition that it shall not, by way of trace or otherwise, be lent, resold, hired out, or otherwise circulated without the pybtshor written consent Pages : x +757 First Edition : April, 2004 VIII Revised & Enlarged Edition IX Revised & Enlarged Edition X Revised & Enlarged Edition : Aug., 2015 [FOR COPIES CONTACT DUR FOLLOWING DISTRIBUTORS 1, UBS Publshers itor Lc, Bengal Ph 2086169, 2001628 2. salvo Bao Hoss, Bonga Pn. zoe, 22257060, 4. Prakash Sai, Borgau, Ph 22054050, 22871030 44. Moyamanir Boot Depo, Hubba Ph: 2264418 5. Virayaka Acorcies, Hutbal Ph 2006612 a cur Shonroons ‘F SADASHIVNAGAR, Noa husshyarn Circe, Bengaluru: Ph: to) 4120 6971 {+ JAYARAGAR, 4” Block, Bengali Pr 08) 4908 9700 {FINDIRANAGAR, Opp. Chinnaya Krishna Temple, Bengalur hy 08) 4045 5060 {+ KORAMANGALA, €t Rosd, 7h Block, Bangaru, Pr: 0) 4063 9909 ‘> RESIDENCY ROAD, Ho. &2, ACR Towers, Bengal hh: (08) 418 6980, {+ ROYAL MEENAKSHI MALL, 2nd Flor, Banrerghata ‘oed Bengaluru Pr; 0) 4258 sx ‘¢ ELEMENTS MALL, 3rd Flor, Thalsandra Mai Road Bengaluru, Ph: (on) 72a 4151 + MYSUAU, Narayan Shastry Roxd, Da Pr: (0821) 4004 “¢ MANGALURU, Eice Mal, K'S. Ra Rose (0820) 4282800, 4+ HUBBALLI, Lauri Mall, Coon Rae Pn, : (0895) 24960 ‘ COMBATORE, No, Eést Poryasvany Road, R'S Purem Combalore«64%082 Ph, : (02) 4€20000 isaiike sein) eee) Iypeserting and Cover Design by : COMNTA LINK, Bengaluru 20. eval: datalinkmadh@ gal.com Printed at: Ravi Graphics, Bengalury naSYLLABUS DESIGN OF MACHINE ELEMENTS - 1 Subject Code: 10MES2 TA Marks 125 Hours/Week —: 04 ‘Exam Hours: 03 otal Hours: 52 Exam Marks — : 100 PART-A UNIT-1 Introd Definitions : normal, shear, biaxial and tri axial stresses, Stress tensor, Principal Stresses, Engineering materials and their mechanical properties, Stress-Strain diagrams, Stress analysis, Design considerations: Codes and Standards, 05 Hours UNIT - IL Design For Static & Impact Strength: Static Strength ; Static loads and factor of safety, Theories of failure: Maximum normal stress theory. Maximum shear stress theory, Maximum strain theory, Strain energy theory, Distortion energy theory. Failure of brittle and ductile materials. Stress concentration, Determination of stress concentration factor. Impact Strength : Introduction, Impact stresses due to axial, bending and torsional loads, effect of inertia, 07 Hours UNIT - 1 Design for Fatigue Strength : Introduction - S-N Diagram, Low cycle fatigue, High cycle fatigne, Endurance limit, Modifying factors : size effect, surface effect, stress concentration effects, Fluctuating siresses, Goodman and Soderberg relationship, Stresses due 10 combined loading, Cumulative fatigue damage. 08 Hours UNIT - IV ‘Threaded Fasteners : Stresses in threaded fasteners, Effect of initial tension, Design of threaded fasteners under static, dynamic and impact loads, Design of eccentrically loaded bolted joints. 06 HoursPART -B UNIT- Vv Design of Shafts : Torsion of shafts, design for strength and rigidity with steady loading, ASME codes for power transmission shafting, shafts under fluctuating loads and combined loads, 07 Hours UNIT - VI Cotter And Knuckle Joints, Keys And Couplings : Design of Cotter and Knuckle joints, Keys: Types of keys, Design of keys, Couplings: Rigid and flexible couplings, Flange coupling, Bush and Pin type coupling and Oldham's coupling. 07 Hours UNIT - VI Riveted and Welded Joints : ‘Types, rivet matcrials, failures of riveted joints, Joint Efficiency, Boiler Joints, Lozenge Joints, Riveted Brackets, Welded Joints ~ Types, Sirength of butt and fillet welds, eccentrically loaded welded joints. 07 Hours: UNIT - VOL Power Screws : Mechanics of power screw, Stresses in power screws, efficiency and self- locking, Design of Power Screw, Design of Screw Jack: (Complete Design). 05 Hours. = vill ~CONTENTS 1, INTRODUCTION LL MACHINE DESIGN; 1.2. PROPERTIES OF MATERIAL; 1,3 DESIGN CONSIDERATIONS: 1.4 CODES AND STANDARDS; 1.5 DISCUSS FACTORS INFLUENCING THE SELECTION OF A SUITABLE MATERIAL FOR A MACHINE, ELEMENT; 6 STRESS, STRAIN, HOOKE'SLAW, STRESS-STRAIN DIAGRAMS & DEFINITIONS; 1.7 STRESSES INDUCED DUE TO NORMAL AND SHEARLOAD; [8 TWO DIMENSIONAL (BI-AXIAL) STRESS FIELD; 1.9 THREEDIMENSIONAL (TREAXIAL)STRESS FIELD; 2. DESIGN FOR STATIC AND IMPACT STRENGTH 55 - 186 2ISTATIC STRENGTH: 22 STATIC LOAD, 2.3 SIMPLE STRESSES; 24COMPOUND STRESS; 2.5 WORKING STRESS; 26F ACTOR OF SAFETY (FOS): 2.7ECCENTRIC LOADING ;2,8'THEORIES OF FAILURE; 2 FAILURE OF BRITTLE. MATERIALS; 2.10 FAILURE OF DUCTILE MATERIALS; 2.11 STRESS CONCENTRATION; 2.12. STRESS CONCENTRATION FACTOR; 2.13 DETERMINATION OF STRESS CONCENTRATION FACTOR; 2.14 METHODS OF REDUCING STRESS CONCENTRATION OR MITIGATION OF STRESS ‘CONCENTRATION (Reter pages 4.24 to 4.28 in New DDH]; 2.15 IMPACTLOAD; 2.16 IMPACT STRESS; 2.17 EFFECT OF INERTIA; 2.18 RESILIENCE AND ‘TOUGHNESS 3. DESIGN FOR FATIGUE STRENGTH 187 - 261 SLINTRODUCTION; 3.2 DEFINITIONS; 335.N. DIAGRAMS AND ENDURANCE LIMIT, 3.4 EFFECT OF FACTORS ON ENDURANCE LIMIT; 3.5 FATIGUE 'STRENGTHUNDER FLUCTUATINGSTRESSES; 3,6 STRESSES DUETOCOMBINED. LOADING; 3.7 CUMULATIVE FATIGUE DAMAGE : MINER'S RULE 4. THREADED FASTENERS 262-310 4.1 THREADED FASTENERS: 4.2 THREADED FASTENER (FIG. 4.1]: 4.3 THREADED SCREW TERMINOLOGY; 4.4 FORMS OF SCREW THREADS; 45 RIGHT HAND AND LEFT HAND THREADS; 4.6 INDIAN STANDARD ‘THREAD; 4.7 STRESSES IN SCREW FASTENING DUE TO STATICLOADING: 4.8 EFFECT OF IMPACT LOADING; 4.9 EFFECT OF FATIGUE LOADING; AIOECCENTRICLOADING;DESIGN OF SHAFTS 311-398 5.1 TORSION OF SHAFTS; 5.2 DESIGN FOR STRENGTH AND RIGIDITY WITH STEADY LOAD, 5.3 TYPES OF SHAFTS; 54 PROPERTIES OF SHAFT MATERIAL; 5.5 HEAT TREATMENT OF SHAFT; 5.6 METHODS OF MANUFACTURING ‘SHAFTS; 5.7 ASME AND BIS CODES FOR DESIGN OF TRANSMISSION SHAFTS; 5.8 FORMULAE USED; 5.9 SHAFT MOUNTINGS; 5.10 FORCES ACTING ON THE ‘SHAFT DUE TO BELT DRIVE: 5.11 FORCES ACTING ON THE SHAFT DUETO GEAR DRIVE; 5.12 STANDARD SIZES FOR SHAFTS COTTER JOINT AND KNUCKLE JOINTS, KEYS AND COUPLINGS 999 - 474 COTTER JOINT 6.1 COTTER; 6.2 COTTER JOINT; 6.3 TYPES OF COTTERJOINTS; 6.4 MERITS AND DEMERITS OF COTTER JOINT; 6.5 SOCKET AND SPIGOT COTTER JOINT; 6.6 SLEEVE AND COTTER JOINT: 6.7 KNUCKLE JOINT: 6.8 KEYS; 69 TYPES OF KEYS; 6.10 STRESSES IN KEYS; 6.11 STRENGTHOF SQUARE KEY: 6.12 LENGTH OF KEY: 6.13SPLINE (FIG6.15|: 6.14 PINS [ROUND KEYS}; 6.15 COUPLING; 6,16 MUFF OR SLEEVE COUPLING, 6.I7MARINE TYPE. FLANGE COUPLING; 6 18 FLANGE COUPLING (PROTECTED OR UNPROTECTED. TYPE); 6.19 PIN OR BUSH TYPE FLEXIBLE COUPLING; 6.20 OLDHAM'S COUPLING 7, RIVETED AND WELDED JOINTS 475 - 597 7.1 RIVET: 72RIVETING: 7.3 CAULKING AND FULLERING; 7.4 RIVET HEADS; ‘1.5 TYPEOF RIVETED JOINTS, 7.6TERMINOLOGY, 7.7 FAILURE OP RIVETED JOINTS; 7.8 STRENGTH OF JOINT; 7.9 EFFICIENCY, 7.10 RIVETEDJOINT FOR BOILER OR PRESSURE VESSELS, 7.| | PRESSURE VESSEI.OR BOILER JOINTS; 7.12 STRUCTURAL JOINTS; 7.13 RIVETED BRACKETS; 7.14 WELDED JOINTS; 7.15 TYPES OF WELDED JOINTS; 7.16 STRENGTH OF BUTT-WELD: 7.17 STRENGTH OF LAP OR FILLET WELDS; 7.18 AXIALLY LOADED UNSYMMETRICAL WELDED SECTIONS: 7.19 WELDED JOINT -ECCENTRIC LOADING 8. POWER SCREWS 7 598 - 655 8,1 INTRODUCTION; 82 MECHANICS OF POWER SCREW; 8.3 EXPLAINSELF LOCKING AND OVERKAULING IN POWER SCREWS; 8.4 EFFICIENCY OF SELF LOCKING SCREW; 8.5 COLLAR FRICTION; 8.6 ANGULAR THREADS - ACME AND TRAPEZOIDAL THREADS; 8 7STRESSES IN POWER SCREW: 8.8 BEARING PRESSURE, 8,9 SHOW THAT EFFICIENCY OF SELF LOCKING SCREW IS LESS “THAN FIFTY PERCENTAGE (50%); 8.10 EFFICIENCY VS HELIX ANGLE (LEAD ANGLE} Additional VTU Problems 656 - 709 VTU 2006 Batch Question Papers 110-737 VTU 2010 Batch Question Papers 738-7571 INTRODUCTION 4,1 MACHINE DESIGN ‘Machine design is the art of developing new ideas for the construction of machines and expressing those ideas in the form of plans and drawings. Design Procedure : The procedure for designing a machine usually involves the following, important steps. i it iit iv. . vi Statement of problem Analysis ofthe problem Selection of mechanism, materials and stresses Preparation of the preliminary design Revision of design ‘Making the final drawings Statement of problem Involves writing down all the data and also what is required. This information will indicate the nature of the problem and purpose of the design.Design of Machine Bements -| Analysis of the problem Itis the analysis of all extemal and internal forees acting on the machine part, The various forces are, (i) Forces or load due to the energy transmitted by the parts (i) Porces due to dead weight (iii) Forces due to frictional resistance (iv) Inertia forces due to changes in velocity. (¥) Centrifugal forces duc to changes in the direction of motion (vi) Forces due to changes of temperature (vii) Forces due to procedures in manufacturing (viii) Forces due to the shape of the pact etc Assumptions, sketches, direction of forces, magnitude, point of application of the forces etc must be considered while analysing the problem. iii, Selection of mechanism, material and stresses ‘The most important part in designing a machine is to select the proper mechanism, material and allowable stresses. Mechanism : While selecting a mechanism importance must be given to strength, accuracy of motion, efficiency and cost. Material : While selecting.a material consideration must be given to the life of various parts, availability, application and cost. Stress ; The selection of proper allowable stress while designing a machine clement requires the working knowledge of materials, The selection must be based on the analysis of load variations, stress distribution due to abrupt changes in sections and other working conditions. iy. Preparation of preliminary design ‘The purpose of the preliminary design is to determine the probable dimensions of all the parts. While deciding the dimensions strength, rigidity and resistance to wear must be considered. ‘The shapes decided upon in the preliminary design must be drawn on paperin the form of free hand sketches. Also in preliminary design al calculations must be completed as far as possible and noted in.a reat legible form, v. Revision of design Before working drawings are made from the sketches of the preliminary design, these sketches, musi be revised (o take into account of all practical requirements such as manufacturing requirement, ‘operation requirement, assembly requirement etcre Intedction $$$ 3 Manufacturing Requirements "The first step in revision is to consider the problems of manufacturing such as those involved in the making of patterns, methods of forging, machining etc. Operation requirements ‘The second step in revision is to consider the problems in operation such as provision for lubrication, safety problem, holding the part, adjustment for wear etc. Assembly Requirement ‘The last and final step in revision begins when the designer starts to make assembly drawings. Here ease of assemblying, dismantling and maintenance should be considered. ‘The assembly drawing should give, all the dimensions and information needed for assembly and installing the machine, vi Making final drawings Once the assembly drawings are ready, all possible revision has to be taken into account while preparing the working drawings. ‘A working drawing must be clear, concise and complete. It must have enough views and cr0st-section to show all the details, Every dimension must be given, so that there will beno scope for guess work ‘A.working drawing must give all the information needed for the men in shops working on it for such as making the pattern, mould, cast the piece, welding, machining, heat treatment etc, Bill of material : ‘When the design of a mechanism and the assembly of ¢ machine is completed, a bill must. show the details of components or parts, umber of parts and the material in which the paris are made etc., the bill of material must also contain details of all standard parts such as bolts, nuts, washers, cotters, pins etc 1.2 PROPERTIES OF MATERIAL : Classification of Engineering Materials: The engineering materials are mainly classified as: (i) Metals and their alloys such as iron, steel, copper, aluminium ete, i) Non-metals such as glass, rubber, plastic etc. ‘The metals may be further classified as : (a) Ferrous metals and (b) Non-ferrous metals. ‘The ferrous metals are those which have iron as their main constituent such as cast iron, ‘wrought iron and steel, ‘The non—ferrous metals are thoye which haye a metal other th suck as copper, aluminium, brass, tin, zine ete, mas their main constituent4 Design of Machine Elements -1 Choice or Selection of Engineering Material The choice of materials depends upon the following factors. Availability of the materials Suitability ofthe materials for the working conditions in service ‘The cost of the materials ‘The important properties which determine the usage of the materials ace physical, chemical and mechanical properties. Physical Properties of Materials ‘The important physical properties of the materials are lustre, colour, size, shape, density.electrical conductivity, thermal conductivity and melting point. Mechanical Properties of Materials [VTU, Dec.2011] ‘The important mechanical properties of the materials are: (i) Elasticity (ii) Plasticity (iii) Ductility (iv) Brittleness (v) Malleability (vi) Toughness (vii) Hardiness (viii) Strength (ix) Stiffness (x) Resilience (xi) Creep Elasticity Is the property by virtue of which a material deformed under the load is enabled to return to its original dimension when the load is removed. Ifa body regains completely its original shape, it | is said to be perfectly elastic. In Fig 1.1, the specimen is loaded only upto point A, well within the | elastic limit E, When the load, corresponding to point A. is gracually removed the curve follows | the same path AO and the strain completely disappears. Such a behaviour is known as the elastic | behaviour. This property is desirable for matcrials used ia tools and machines. Stecl is more clastic | than rubber. Plastie—— strain (e) oe Fig. LI Plasticity Itis the converse of elasticity. Its the property of a material which retains the deformation produced under load permanently. This property of the material is necessary for forging, stamping ‘mages on coins and in ommamental work._— Introduction: Duciiity It is the property of a material which permits a material to be drawn out longitudinally to & reduced section under the action of tensile force. A ductile material must be strong and plastic, The ductility is usually measured in terms of percentage clongation or percentage reduction in /s arca of the test specimen. The property of ductility is utilised in wire drawing, The commonly used ductile matericls are mild steel, copper, aluminium, nickel, zinc, tin and lead. Brialeness Itis the property of a material opposite to that of ductility ie., lack of ductility. A material is said to be brittle when it cannot be drawn out by tension to smaller section, In a brittle material failure takes place under the load without significant deformation, This property is usually ‘undesirable. Examples of brittle materials are cast iron, high carbon stecl, concrete, stone, glass, ceramic materials etc. Glass is an ideal brittle material in which stress-strain curve in tension is essentially a straight line. Malleability 11s the property of a material which permits the material to be extended in all directions without rupture. (i.e, 10 be rolled or hammered into thin sheets ). A malleable material possesses ahigh degree of plasticity but not necessarily great strength. This property is utilised in forging, hot rolling, drop stamping ete. The commonly used malleable materials are lead, soft steel, wrought iron, copper and aluminium. Toughness Tis the properry of a material which enables it to absorb energy without fracture (ic, to resist fracture due to high impact loads). This property is desirable in parts subjected to shock and impact loads, Toughness is measured in terms of energy required per unit volume of the material to cause rupture under the action of gradually increasing tensile load. Fig 1.2 shows the siross-strain curves for mild steel as well as high carbon steel. The toughness is represented by the ‘area under the stress-strain curve for the material. High Carbon Steel Mild Stee! Unit strain —> Fig, 1.26. esign ot Machine torments -1 Hardness isthe ability of material to resist indentation or surface abrasion, Itembraces many different properties such as resistance to wear, scratching, deformation and machinability etc, Tests on harcness may be classified into (@ Scratch Test (ii) Indentation Test ‘The Scratch test consists of pressing a loaded diamond into the surface of the specimen and then pulling the diamond so as to make a scratch, ‘The Indentation test consists of pressing a body of standard shape into the surface of the test. specimen, Example Brinell hardness test, Rockwell hardness test and Vickers hardness test. Strength ‘This is the most important property of a material from design point of view. Its the ability of material to resist the externally applied forces without breaking or yielding. ‘The load required to cause fracture divided by the area of the test specimen is termed as the ultimate strength of the material and is expressed in the unit of stres Stiffness Itis the ability of a material to resist deformation under stress, The modulus of elasticity is the measure of stiffness in axially loaded members. Resilience It is the property of a material to absorb energy and to resist shock and impact loads, I is ‘measured by the amount of energy absorbed per unit volume within elastic limit. This property is important for spring materials. Creep When « partis subjected to 2 constant stress at high temperature for a longer period of time, it will undergo a slow and permanent deformation cailed ereep. This property is considered in designing LC. engines, boilers anc turbines, 4.3 DESIGN CONSIDERATIONS Based on the circumstances and the need, quite a number of characteristics mustbe considered in designing a part, Some of the important characteristics are as follows : (i) Strength (ji) Safety (iii) Stiffness (iv) Surface finish (¥) Shape (vi) Size (vii) Styling (viii) Usilty (ix) Reliability (x) Cost (xi) Life (xii) Wear (xiii) Corrosion (xiv) Weight (xv) Noise (avi) Flexibility (xvii) Control (xviii) Lubrication (xix) Maintenance (xx) Liability (xxi) Volume (xxii) Friction (xxiii) Processing (xxiv) Thermal Properties. 1.4 CODES AND STANDARDS [VTU, DEC.2011] Code sa set of specifications forthe analysis, design, manufacture and construction of something. ‘The main purpose of code is to achieve a specified degree of safety, efficiency and quality. Standard is the set of specifications for parts, materials or processes intended to achieve uniformity, efficiency and a specified qualivy.er 7 iroducton| ‘The organisations and societies listed below have established specifications for standards and safety or design codes. ‘Aluminium association (AA) ‘American Gear Manufacturers Association (AGMA) ‘American Institute of Steel Construction (AISC) ‘American Iron and Steel Institute (AISI) Society of Automotive Engineers (SAE) Industrial Fasteners Jastitute (IF) British Standands Institution BSD) American Society of Mechanical Engineers (ASME) Institution of Mechanical Engineers (1. Mech, E) National Bureau of Standards (NBS) American Welding Society (AWS) International Standards Organisation (ISO) American Society of Metals (ASM) Antiftiction Bearing Manufacturers Association (AFBMA) American Society of Testing and Materials (ASTM) American National Standards Institute (ANSI) Standardisation ‘Standardisation aims at establishing mandatory or obligatory norms or standards to which the different types, grades, parameters such as length, diameter, etc, quality characteristics, est methods, rules of marking, packing, storage of finished items, raw materials and semi-finished articles should confirm. The main purpose of standardisation is to minimise variety, Bureau of Indian Standards (BIS) has standardised a number of items for the benefit of designers. They are: (@ Rules for preparing drawings. (i) Symbols and notations for mechanical quantities and their units. (ii) Engineering materials, their chemical composition, mechanical properties, method of heat treatment and methods of mechanical testing (iy) Dimensions and preferred sizes of various machine components, (9) Fits and tolerances for various machine elements from assembly considerations. ‘The advantages for the standardised parts are = (Standardised products have better quality and are more reliable. (i)_As the standardised parts are easily available for replacement, maintenance is easy, ii). Service life for the standardised parts is higher. (iy) Time and effort required to manufacture a new machine is less with the use of standard components.2. Dnrtign of Machine torments «1 1.5 DISCUSS FACTORS INFLUENCING THE SELECTION OF A SUITABLE MATERIAL FOR A MACHINE ELEMENT [B.U. Feb. 96, Feb. 97, VTU, May/June 2010] ‘All materials have certain inherent charactevistics which must be considered for the selection of a particular design, The factors o be taken into account are strength (yield and ultimate) stiffness or rigidity, ductility, toughness, resistance, fatigue resistance, ductile to brite wansition, creep resistance, ‘wear resistance, oxidation and corrosion resistance, thermal and electrical conductanee, friction characteristics, hardenability, castability, formability, weldability, machinability and specific weight ete, The material selected should be readily availablein required quantity. Sometimes multiple choice may be possible and the eost and maintenance ofthe finished product decides the final choice. ‘The broad classification of the engineering materials are given below. From this study the basic characteristics of exch metal and select the proper one Engineering Materials eee Meaallic Non-Metallic (plastic, rubber, leather, wood, i glass, ceramic & carbon ) Ferrous (iron andits Non-Ferrous alloys such as cast iron, carbon steel and alloy steels ) White metals (Ni, Silver and their alloys) Copper alloys Light weight metals and their alloys (Zn, Al, Mg and their alloys) others (Rare metals ‘Aniifrction alloys and theiralloys) Bearing metals ‘After selecting a proper material, the final selection of a material for the design is based on the ‘most economical production method. The following chart gives the brief account of various ‘manufacturing process from the designers point of view,SOMtsOgPY “8 Suipjom sose; pur ueeq wonse1g Sunpuy Surerg. pue Surpunip “> pue Suuspjos “9 Sunmopramy “¢ Zuppa uumsy, 5 Guymon {so Tudues Sans pean Buppmsey p, “219 “Buuways “Bunwesp Sinessig te fuunseu ZuppRamo “€ Sumypeaiq, ‘vorsnma Sua eee eaioe qeuonipen-uoN Supp Sammd = “Bujorseypns: unses A@inepw — S0URsIsy -z~ CudoysGuyn —uBOM PION TZ —BuBioFarq -¢ pInow quouewiag “T sepmog | Supjmary +] Suqup Tummy, -~ — SuppomyoH | Fuiy MUG “| Sunseo pues “] SuaHLO ‘ONINIOF fONINIHOVIN'| =| ONIWAOA| | NTOYOA SNTISVD eats [11 spompayy Sup moegnueyy, naan BO ee ea eee10 Design of Viachine Elements -1 1.8 STRESS, STRAIN, HOOKE'S LAW, STRESS-STRAIN DIAGRAMS & DEFINITIONS 1.6.1 Load Itis defined as any external force acting on a machine part. The following four types of loads are important, they are @) Dead or Steady load : A load is said to be a dead or steady load when it does not change in magnitude or direction. Gi) Liveor Variable load : A load is said to be a live or variable load when it changes continually. (ii) Suddenly applied or Shock load : A load is said to be a suddenly applied or shock load when itis suddenly applied or removed. (iv) Impact load : A load is said to be an impact load when itis applied with some initial velocity 1.6.2 Stress When a body is acted upon by externel foree or load, internal resisting force is set up, such a body is said to be ina state of stress, hence stress is the resistance offered by the body to deformation, ‘The intemal resistance offered against the external force may be assumed to be uniformly distributed over the whole area of cross section. Thus this intemal force per unit area at any section of the body is known as stress, Its denoted by 6 (sigma), A loaded member remains in equilibeiam when the resistance offered by the member against deformation and applied load are equal i., F=F F © Suess 0 = = — where F' = Resisting force, A A normal to the axis or direction of applied load Applied force, A= Area of c/s WA Pe t oF 1B ai Ve ES resisting ree i ta resising cet) $=] _—_— ee t A rer F Lor SS Fig. 13i Introduction: ‘The following are the important types of stresses. () Normal stress. Itis classified as (a) Tensile Stress, (b) Compressive Stress (ii) Shear Stress or Tangential Stress (ii) Bearing Stress (iv) Bending Stress (9) Twisting or Torsional Stress } () Axial Load |The Force acting slong the axis of the rod is known as axial load as shown in fig 1.4 | Fe—f =. >F Fig, 14 i) Normal Stress ‘The internal forces and the corresponding stresses acting in the direction perpendicular to the surface is known as normal stress or direct stress. Normal stresses are of two types (a) Tensile steess and (b) Compressive stress, (a) Tensile Stress When a load is acting in such a way that it tends to pull apart the particles of the material causing extension in the direction of application of load, then the load is called tensile load and the corresponding stress ‘tensile stress’, ' A 1 a re— F Fe 1 >F + i SST Fig, 15 (0)12 Design of Machine Elements) ax{ ule Fig : 1.5 (a) shows a bar subjected to the tensile force F. Fig: 1.5 (b) shows resisting force a section AB. For equilibrium, resisting force F'= Applied force F Fig: 1.5 (©) shows an element in the material which is subjected to tensile stress. Resisting force F’ Gross Sectional Area A © = F where F = Tensile 2. Tensile Stress = toad) s 0 = FA Némmt or Nim Compressive Stress When the load is acting in such a way that it pushes the particles of the material nearer causing shortening in the direction of load, then its called compressive load and the corresponding suress "compressive stress”. ' Fig. 1.6 (6)13 Introduction o—| k—o Fig. 16 (0) Fig: 1.6 (a) shows a bar and an element subjected to a compressive load. Fig: 1.6 (b) shows resisting force at section AB. For equilibrium resisting force F° ‘Compressive load F Fig : 1.6 (c) shows an element in the material which is subjected to compressive stress pplied Resisting force F* Cross Sectional Area A | Compressive stress. Hence Compressive stress o = F=P4F =2F] +. Average shearing stress“Introduction: Tee. x YA Le YAW CY aaa Bearing Stress Bolts, pins and rivets create stresses in the member they connect zlong the bearing surface or surface of contact. A localised compressive stress at the surface of contact between two members ofamachine part that are relatively at rest is known as bearing stress or crushing stress Consider two plates connected by a bolt as shown in the Fig 1.8. The bolt exeris a force F° equal and opposite to the force F exerted by the plate on the bolt. The force F' represents the resultant of elementary forces distributed on the inside surface of a half eylinder of diameter ‘d’ and length ‘t’ equal io the thickness of the plate. Since distribution of these forces and the corresponding stresses is quite complicated, the average nominal value of G, called the hearing stress is obtained by dividing the load F" by the area of the rectangle representing the projection of the bolt on the plate section, POE Bearing stess 6, = “= jg where t = "Thickness of plate and d= Diameter of the bolt >F - Fig. 1816 —$_— Design of Mectine Elements - 1.6.3 Strain When a force or load acts on a body it undergoes deformation. This deformation per unit, Jength is known as unit strain or simply strain, It is denoted by € (epsilon) or e strain € Where 6 = Deformation 1 = original length Swrain is dimensionless. Strain may be u (i) Tensile strain Gi) Compressive strain (ii) Volumetric strain iy), Shear stra (v) Superficial sirain (i) Tensile Strain Lot AB be the initial length of the bar before the application of the load and AC be the final length after the application of the tensile load F as shown in Fig 1.9 *. Extension or Change in length = AC - AB = BC = Original length = | ‘The extension per unit length is defined as tensile strain, Extension of bar__ 6, 1. Tensile sain = Gest Tengthofbar = 1 Fig. 19 (i) Compressive strain : Consider a uniform bar AB of initial length I subjected to a compressive force F, The length of the bar reduces to AC as shown in Fig 1.10 :, Shortening or change in length = AB~ AC = BC = 5,Infredtuet.on $$ $aSaé@a@a@ @@ Mm@- —@- ———_—— 17 Compressive strain is defined as shortening per unit length. Shortening of the bar 8, Compressive strain © = Orginal length of bar ” 7 Shear Strain : Consider an element ABCD as shown in Fig 1.11 is subjected to shearing stresses on faces ‘AB and CD. I: undorgoes deformation and this deformation is expressed in terms of the angular cisplacement. ‘Transverse displacement _ DD, _ 8s, Distance AD “AD ht © Shear strain 6 = ian p=0)18 (i) Volumetric Strain : Volumeiric strain is defined as change in yolume per unit volume Design of Machne Elements -1 by * Volumetric strain = —* (©) Superficial Strain: Superficial strain is defined as change in area per unit area 1.6.4 Elastic limit When an external force acts om a body, the body tends to undergo some deformation. If the external force is removed the body comes back to its original shape and size. The body will regain its previous shape and size only when the deformation caused by the extemal force is within a certain limit, The value of the force corresponding to this limit is called limiting force. The value of stress corresponding to this limiting force is known as the elastic limit of the material, 1.6.5 Hooke's Law It states that when a material is loaded within elastic limit, the stress is directly proportional to the strain, Le, the ratio of stress to the corresponding strain is a constant within the elastic limit. This constant is known as Modulus of Elasticity or “Young's Modulus”, se Stress ce strain Stress ie, = constant Strain ‘oung’s modulus o ie, > =E where € 1.6.6 Poisson's Ratio ‘When a body is subjected to direct stress, it undergoes deformation in the direction of load and at rightangles to the direction of load. There is an increase in length inthe direction of load but decrease in the lateral direction as shown in Fig 1.12, The strain in the direetion of load is known, as longitudinal strain and the strain at right angles to the direction of applied load is known as lateral strain ‘The ratio of lateral strain to the longitudinal strain is defined as Poisson's ratio and is «constant. 1 Itis normally denoted by — or or v(nu). The value of m for mest of the material lies between 3 and 4,Inttoduction Ets il rs Fig, 112 D-d), (B-b) Lateral strain Ds) longitudinal sirain 8, = Decroase in depth =D-d 8, = Decrease in widih = 8, = Increase in length ~. Poisson's ratio In the case of a tension member, if the strain in the direction of load is ©, then the strain E 1(o, 1 fo, 7 inte erro dren (26) na (21) epetne 1.6.7 Stress-strain diagram [VTU, June/July 2011, June/July 2014] ‘The mechanical properties are commonly determined from a standard tensile test. The testing ‘machine is called universal testing machine (UTM), The test consists of gradually loading a standard specimen ofa material and noting the comesponding values of load and elongation until the specimen fractures. The load is applied and mezsured by a testing machine. The stress is determined by dividing the load values by the original cross sectional area of specimen. The elongation is measured by determining the amount thattwo reference points on the specimen are moved apart. The original distance between the two reference points is known as gauge length, The strain is determined by dividing the elongation values by the gauge length. ‘The valucs of the stress and the corresponding strain are used to draw the stress-strain diagram of the material tested. The Fig: 1.13 shows the stress-strain diagram for mild steel. The various properties of material are discussed below.20 —$ $$ Design of Mactine Eismments -| ‘True stress, / strain curne Nominal or Conventional or Engineering stress-strain curve Strose— o Sain —> Fig. 1.13 (New DDHB Fig 1.1) 1. Proportional limit From O to P the curve is a straight line, ie, steess is directly proportional to strain, Therefore it is clear that Hooke’s law holds good up to the point P and this point is known as proportional limit, Iv is defined as a point at which the stress begins to deviate from the straight line. 2. Elastic timit Up to the point E the material will regain its shape and size, when the load is removed. It ‘means that the material has elastic properties up to the point E, This point is known as elastic limit 3. Yield point If the material is stressed beyond the point E, the plastic stage will reach i.e, on the removal of load, the material will not be able to recover its original shape and size. [At point Y, there is an increase in strain without appreciable increase in load, Thus the curve crops down tothe point Y,. Then again with the increase in load the strain increases andis practically ‘constant up to the point Y. This phenomenon of inerease in strain without any eppreciable increase in load is called yielding. The point Y, is called upper yield point and the point Y, is called lower ‘yield point. In practice the lower yield stress is more impostant and hence this point is called yield point. 4. Ultimate stress Between the points Y and U the ductile extension takes place. Here the relationship between stresg and strain depends upon the rate of loading also. During the extension the cross-sectional area decreases uniformly all over the length such that the volume remains constant. At the point U, the stress attains its maximum value which is known as ultimate point. The stress at this point is {known as ultimate stress. Itis defined as the maximum stress obtained by dividing the maximum yelue of the load reached to the criginal cross-sectional area of the test specimen.—_— Introduction 21 5. Breaking stress ‘After the maximum load is reached, local yielding takes place and a neck or waist is formed. AAs the cross-sectional area decreases considerably the load carrying capacity of the specimen reduces and hence in the portion UB the strain increases for decrease in stress. Even though the nominal stress is decreasing, the actual (true) stress which is equal to the load divided by actual cross-sectional area at neck will be continuously increasing. At point B the specimen breaks, The stress at this point is called breaking stress and the corresponding load is called breaking load. The ralure of fracture for mild steel will be in the form of cup and cone, 1.6.8 Stress — strain curves for other materials Fig 1.14 shows stress ~ strain curves for steel having carbon content yarying from 0.12% 10 19. From these, it is concluded that with high carbon content it is similar to brittle materials even though the ultimate stress is much greater. 1400 ne 119 0 840) i wo 2 B a9 2 v9 lose ae ss Nm’) 0 020 3040 Percentage Strain Fig. 114 Fig: 1.15 shows typical stress — strain diagram for common materials such as high carbon steel, nickel-chrome steel, mild steel, wrought iron, cast iron, copper and cast aluminium, From these it is noticed that for steel and wrought iron proportionality exists almost until yielding takes place. For copper, cast aluminium and high alloys, no clearly defined limit of proportionality, elastic limit or yield point. Cast iron behaves like a brittle material which fails without any visible elongation or reduction in area.Design of Machine Elements -1 22 igh 4 a Wife ian Chore Guakam 6 iw 20 30 w 0 153 Percentage sain Fig. 115 Fig : 1.16 shows stress-strain diagram for aluminium alloy. Itexhibits considerable ductility, though itdocs not have clearly definable yield point. 280 ma ad & / a | * 40] Wea as RL Pig 16 Fig : 1.17 shows stress - strain diagram for hard rubber and soft rubber. The curve for hard rubber is linear up to very large strains, Soft rubber continue to stretch enormously without failure. 21 tai Rube} Stress (Nimm*) }—~] c 7 4,0 8 ig 117Cc Heston $$ ir Fig: 1.18 shows the stress ~ strain curve for brittle material. Itis seen from the diagram that the deviation from Hooke’s law begins very early and fracture occurs suddenly with very small deformation and without necking, The stress ~ strain diagram for brittle material does not exhibit theyield point, Examples of brittle materials are concrete, stone, cast iron, glass & ceramic materials ce, Glass is an ideal brittle material, exhibiting almost no ductility, Tage “ Fig. 1.18 (New DDEB Fig 1.2) Note : 1, Materials with more than 15% elongation are usually considered ductile, 2, Materials with less than 5% clongation are considered as brittle. 3. Many ductile materials have the same yield point in tension and compression, 4, Most brittle materials have a higher value for ultimate strength in compression than that for tension, 5, Percentage elongation is the percentage increase in length of the gauge length. L +. Percentage elongation =p" x 100 where L,,= Original gauge length 1L,= Final longth between gauge marks, 6, Percentage reduction in areais defined as the ratio of maximura change in the cross-sectional Agra, area 0 original cross sectional area, expressed in percentage reduction in area = $9 where For ductile material percentage reduction in area is $0 to 70.24 —<——— Design 0f Machina Eloments =| 4.7 STRESSES INDUCED DUE TO NORMAL AND SHEAR LOAD In actual practice at any point in a strained material combination of tensile, compressive and shear stresses ie. different stresses may act on planes. Hence it is necessary to find the resultant stresses which may be greater than the applied ones and also the planes on which they act. The systemsin which direct stresses and shearing stresses act simultancously are called combined stresses ‘or compound stresses, Here the study is limited to two dimensional stress system only. 1.7.1 Methods for determining stresses on oblique section (i.¢., Inclined plane) cs on oblique section are de:ermined by the following methods, The sires (i) Analytical method Gi) Graphical method ‘The following three types of stressed conditions in an element are considered. (i) Uniaxial stress. i) Biraxial stress, (ii) General qwo dimensional stress system. “To find the stresses acting on an inclined plane ina stressed material, consider a plane inclined ‘at an angle 6 to the knowa plane and then find the normal and tangential (shear) stresses on this plane. 1.7.2 Sign Convention (i) Tensile stress is considered as positive. (ii) Compressive stress is considered as negative. Gil) Angle @ is considered positive when it is in the anticlockwise direction. Gv) A shear siress acting on the positive face of an element is considered positive and negative if it acis in the negative direction of the axes. ic., shearforce acting x - face giving rise to cow couple is treated 2s positive and ew couple is treated as negative. ey chia € -feco face —————— id ytace ytace Positive shoar stress Negative shear stress Fig 1.19 (v) 6, is positive in tension. (vi) o,is positive when it tends to produce counterclockwise rotation ofthe element and negative when it tends to produce clockwise rotation of the element.ry intoduction ——__________—?_—. 5 1,73 Prineipal stresses and Principal Planes Principal planes are the planes on which only normal stresses will act with zero shear stress The normal stress across the principal plane is known as principal stress. ‘Atany point ina strained material, under three dimensional stress system, there are three such planes mutually orthogonal to each other, which carry direct stresses only and no shear stress. Out ofthese, the plane carrying the maximum normal stress is called the major principal plane and the ‘normal stress acting on that plane: called the major principal stress, The plane carrying the minimum hormal siress is known ¢s minor principal plane and the corresponding normal stress acting on that plane is called the minor principal stress. In a plane stress or two dimensional stress system, the third principal stress is zero. 1.7.4 Member subjected to direct stress on one plane [i.e., Uniaxial stress] Consider an element subjected to direct uniaxial stress or load as shown in Fig. 1.20 Fig 1.20 Consider a rectangular member ABCD of uniform cross-sectional area with unit thickness subjected to uniaxial tensile Load as shown in Fig. 1.21 oD G = c r———_ a -——- F a e 8 ig 12 Let F = Axial tensile force acting on the member, A = Area of cross-section. Consider a plane EF which is perpendicular to the line of action of the force. ‘Area of cross section EF = EF x1 =A Axial tensile fore F Stress on plane EF, 6, = ~\ a ateys BF 7 A26 Design of Machine Elements -1 ‘The stress on plane BF is entirely normal stress and there is no shear stress. Now consider & plane £G at an angle @ with the normal plane ZF as shown in Fig. 1.21, Angle @ being measured in anticlockwise direction, EF A pert cos" ~ cost ‘The applied force F is parallel to the axis of the member and not normal to the plane EG. ‘Since all the parts of the member have the same axial strains, the stresses acting on the plane EG are uniformly distributed as shown in Fig. 1.22(a). The resultant force due to these stresses will be a force, equal in magnitude to the axial force F. This resultant force F acting on plane EG may be resolved into two components as shown in Fig. 1.22 (b) G Area of cross section EG = EG x t= EG x1 = E (a) to) Fig, 1.22 (Normal force F, acting normal to the plane EG. i) Tangential force F, acting tangential to the plane EG. Normal force F, = F cos 0 Tangential force F, = F sin 8 Normal force Fy __-Feos® _ Feos?@ ©. Normal stress across the plane EG, 0, = ‘Area of section EG ~ A/cosO~ A FP = 0,c05'0 (0, =7 2.10 (Olé DDHB) 2.13 (New DDHB) Area of section EG Tangential stress ({.e., shear stress) across the plane EG, t, Fsing oF =~ A ycosp 77 4 2 BOSE =-Fasindcosa=-Ssin20 2.11 OwDDHB) 2.14 (New DDHB) Negative sign indicates that t, tends to produce clockwise rotation of the element, Normal stress 6, is maximum when ® = Maximum normal stress 6, = 6, €050= 6, 2.12 (Old DDHB} 2.15 (New DDHB)2 reduction Minimum normal or principal stress 6, = 0 when @ = 90° ‘Tangential stress, is maximum when @ = + 45° The maximum positive value of, is obtained at value of ¢, is obtained at 0 = 45° 45° or 135° and the maximum negative --2.13 (Old DDHB) 2.17 (New DDHB) Hence all planes inclined at 45° to the axis of pull are subjected to maximum shear stress +. Maximum shear stress py, = 6, equal to S* Fig. 1.23 shows the variation of 6, and ty as © varies from —90" 10 + 90° ‘When @ =0, plane £G becomes a cross section EF and hence the graph gives o,= 0, as 0 increases and when 0 0°, 6,= 6, = 0 indicating that there is no normal stress on a plane parallel to the longitudinal axis, Similarly on Fig. 1.23 planes where @ =0, 7, = 0 and also on longitudinal sections where @= + 90°, t4 = 0. When 0 =— 45°, maximum positive value oft, is obtained and wien @=+45°, maximum negative value of ty fs obtained as shown in Fig. 1.23 90° “90° ‘The resultant stress may be found out from the relation 6, = fo; +g. The relation holds 200d for compressive stress also, 1.7.5 Member subjected to direct stresses on two mutually perpendicular directions, [Bi-axial stress] Consider a rectangular block ABCD whose thickness perpendicular to the plane of the paper isunity. The bars subjected to :wo direct tensile stresses or Wa principal tensile stresses as shown in Fig. 1.24 60— re iat corre: Element | Solution = ‘Maximum allowable normal ste38, Cy Maximum shear stess 1. Now, £204 201; B= Me From Figure 4.22 (Old DDHB); sur coreaton ter KAS Eas Aico, = fa - sus sata = 88 KY va w sexton tna, = Mien 12 Zhen Fig 422 (OU DDB, 2 2 4.18/4.18A (New DIB) 197916.667N mm M, = 9550 « 10 S = 9550.10" x jie, 39.63 307916,667 (°) mye 2 2 ‘37.4 mm say 37.5 mm = Diameter of shaft al the groove Example : 2.41 ‘A stepped shaft of circular cross section show (0,,=431.5 MPa). Determine the value of ot ‘and the fillet radius, so that the maximum stress will limited to a ratio corresponding toa factor of safety of 25 Data: FOS = 25, F=30kN=30 x 10°N50,,= 431.5 Mpa=431.5N/mmt* | Solution : oy _ 4315 + Maximumallowable normal ites = G05 = 7.5 i tema = FOS 25 172.6? D_ 12d aaDotign of Mochine Elements -1 Let BE be the oblique plane inclined at an angle @ on which the stresses are to be calculated, Let 6, = Major tensile siress or principal stress on face AD and BC 16, = Minor tensile stress or principal stress on face AB and CD F, x BCX 1= 6, x BC F, = Tensile force on section BE due to 0,=0, x ECx 1= 6, x EC Resolve the forces perpendicular to BE and along BE as shown in Fig. 3.6 (a) and (b) Tensile force on section BE due to 9, JoxtC=F F sind 0, xBC=F, (a) 8 o) 8 Fig. 1.25 «Total foree perpendictilar tothe plane BE, F, = F, cos 8+ F, sin ® ie, 0,%BE = (6,xBC) cos 04 (6, x £0) sin ® ie, 6, = 6, FC cose +o, #C sino BE BE = 6,c0s 0 cos +6, sin @ sin 6 * 044, sin’ O = 90% (1 46082)+ & (1 - cos 26 2 (1 +008 +> cos 26) =. Normal stress on plane BE, 6, ) x 26 ~-2,26 (Old DDHB) 2.28 (New DDHB), “Total force tangential to the plane BE, F,=~ F, sin @ + F, cos @ ie, t,x BE = ~(6, x BC) sin 8+ (6, x EC) cos 0 ient, =~, 2C sind+0,£C cose 1E BE = ~6,cos Osin@ + 6, sin Ocos © | = ~(6,-0,)sin 0 cos 2.27 (Old DDHB) 2.29 (New DDHB) -. Tangential stress on plane BIInduction ‘is negative since it tends to produce clockwise rotation of the material. ‘The resultant stress on plane BE, 2 9%, = (or+te = (6. in’ 6): +{-(, ~6, )sinBcos®}? = [6 cox 6 +67sin*0+20,., cos? @sin®8+(62 +03 ~26,0, )sin”Ocos" 2 = [63 cos? 6(cos* @ + sin? @) + 0% sin? 6(sin® @+ cos” 8) ¢. Resultant stress on plane BE, 6, = /O; 8+o7 sin’ ‘The angle that the line of action of the resultant stress makes with the normal stress is called the angle of obliquity. ++ Angle of obliquity @ = tan (=) On principal planes, t, musi be equal to zero. te, (25%) ain20 =0 2 4 20=0 or 180%, i1c., 0 = 007 90° E e, ‘When @=0 Major principal stress 6, ‘When @ = 90° Minor principal stress. 0,30 —— Design of Machine Elements - ‘Thus, there are two principal planes at right angles to each other, one of which carries the ‘maximum direct stress and the other the minimum direct stress, These principal planes do not carry any shear stress. ‘Shear or tangential stress on plane BE is maximum when 20 = 90° or 20= 90° or 270, i.e,, 0 = 45° or 135°, When © = 45° maximum negative value of +, is obtained and when @ = 135° maximum positive value of f, is obtained. 6, -9, Wht gg (2552 on0 (° °. 2 Hence there are two mutually perpendicular planes along which the greatest shear stress ‘occurs, These planes are at angles of 45° and 135° with the principal plane carrying principal stress 8. Whea the biaxial stresses , and 6, are not alike ie, if 6, is tensile and is compressive stress, -~2.29 (Old DDHB) 2.31 (New DDHB) When 9 = 135% Tou 2) sin 270° 6.-9, (6,46, Then 6, + 4 Jeo20 5, +6, =| “3” | when 0 =45° or 135° 1.7.6. Stresses induced by state of simple shear ‘The rectangular block ABCD shown in Fig, 1.27 isin a state of simple shear under the action of shear stress intensity +, Let the thickness of block normal to the plane of paper is unity. Now, consider any sectional plane BE inclined at an angle @ with the normal cross-section as shown in Fig. 1.27. Let the normal and tangential stresses on the plane BE be 6, and, respectively. Resolving the forces perpendicular to BE, 6X BE = (1,, x BC) sin 8 + (1,, x EC) 0s © Fig. 127Intioduction 31 BC EC ied, = 4x ge SN B+7,, x pe cOsO = 1, cos @. sin +1, sin @ cos & +, 28in 8 cos 9 (ty) z+ Normal stress on plane BE, 3, 1,, sin 20 ~- 2.20 (Old DDHB) 2.22 (New DDHB) Resolving the forces along BE, TX BE = (t,x BC) cos 8~(1,, x EC) sin @ BC EC ie, = 4, pp 6080-5, x Be sin 1,, 005 0,00 0—t,, sin O sin @ = 1, ( 60s? 6 — sin? @) (ty). 2.21 (Old DDHB) 2.23 (New DDHB) <: Tangential stress on plane BE, %, =T,, cos 26 For the principal planes t, must be equal to zero. ie, t,c0s.28 = 0 iue,,26 = 90° or 270° i.e, 8 = 45° or 135° Hence the two principal planes are at 45° and 135° with respect to the plane BC, The principal plans are also at right angles to cach other. The two principal stresses are 1, sin (2 x45) = +1, 2.22 (Old DDHB) 24 (New DDHB) 6, G, = t, sin x 135)=~71,, ‘Thus on one principal plane there will be tensile stress and on the other there will be compressive ssress, These principal stresses are called diagonal tensile and diagonal compressive stresses For maximum shear or tangential stress, cos 20 = ie. 28 = Oor 180% when 8 = 0 fan = ty 2.24 (Old DDHB) 2.26 (New DDHB) when @ = 90° Tag =~ yy 3.76 ‘Thus the planes BC and CD carry the maximum shear steess intensity ",, Fig. 1.28 shows the planes carrying maximum shear stress and principal stress.Design ot Machine Elements -1 32 Fig. 1.28 1.7.7 Member subjected to two perpendicular normal stresses accompanied with state of simple shear OR MEMBER SUBJECTEDTO GENERAL TWO DIMENSIONAL STRESS SYSTEM ‘Consider a rectangular member ABCD of uniform cross-sectional area and unit thickness subjected to tensile stresses and shear stress as shown in Fig. 1.32, “This body is subjected to, (i) Tensile stress 6, on face AD and BC (Gi) Tensile stress 6, on face AB and CD i) Simple shear stress on face BCand AD ‘According to the principle of state of simple shear, the faces AB and CD will also be subjected to shear stress as shown in Fig. 1.32. Let BE be the oblique plane inclined at an angle 8 on which the stresses are (o be calculated, From the geometry of the Fig. 1.32— {nod} Sai a 8 Horizontal force acting on BC, F, = 6, BC Vertical force acting on BC, F,=%,,BC Horizontal force acting on EC, F, = 1,, EC Vertical force acting on EC, F,=0, BC Resolving the forees perpendicular to the plane BE, F, = F,cos 0+ F,sin @ + F,cos 0+ F,sin 0 i.e, 6,% BE = (6,80) cox + (CBC) sin8 + (tC) cos 8 + (0,EC) sin® sa, 9 = 0, Bcd, ME sinoee, Leonor, EEsind 6,cos 8 cos 0 +1, cosOsin8 +t, sin 8 costo, sin Osin® 6, cos? 9 +6,sin78+21,,sinBcos® — (=, 8. °%, Se +008 20) + FL —c0826) +e, sin 20 ote, (°c <8, Z )con20 +5, 9n20-— 2.30 (Olé DDHB) +. Normal stress on plane BE, = 2,32 (New DDHB) Resolving the forces along the plane BE, F, = —F,sin® + F, cosO—F, sin® + F, cos 8 ie, t,x BE =-(6,BC)sinO + (¢,.8C) cos8~(1, EC) sin + (6, EC) c0s0 jest BC sino 47, 2S cos 8-7, ££ sind +6, Zecose BE "BE “BE BE ~9, co 8 sin Det, cos 0 cos 8-1, sin sin B+ sin @cos 6 =(6,-0,) sin cos 8 +4, (cos? 8 sin?®) (oy T= 7) +. Tangential stress on plane BE, $,-8, (5 * ) sin 20 +, cos 20 2.31 (Old DDHB) 2.33 (New DDHB) Resultant stress on plane BE, 0,= 63 +73 te ‘Angle of obliguity 6 = tar'5~ For the principal plane, tansgential stress on the plane must be equal to zer0. ) sna + 4,002 0=034 Design of Machine Elements - | de; tan 2 = ——8— 2.34 (Old DDHB) 2.36 (New DDHB) There are two principal planes at right angle to cach other and their inclination with the normal cross-section being @, and @,, Equation 2.34 (Old DDHB) or 2.36 New (DDHB) can be represented diagramatically by Fig. 1.33 in which sin2, 0528, sin20, cos20, = Oz \(o.-9,) +4e%, Substituting the values of cos 26, and sin 26, in Equation 2.30 (Old DDHB) or 2.32 (New DDHB) 2.32 (Old DDHB) +. Major principal stress 0 34 (New DDHB)Fete) $$$ $a. 35 Similarly substituting the values of cos 20, and sin 20, in Equation 2.30 (Old DDHB) or 2.32 (New DDHB) 2-5, _) ea 6, Eee + Minor principal stess 0, ~-2.33 (Old DDHB) 2.35 (New DDHB) ‘These principal stresses may be like or unlike. For maximum value oft, differentiating w.rt ® and equating to zero 5, -9, ic, “| 2 cos 20’ - 1,,x2sin 26'=0 ie, 2t, sin 20’ = -(6,-0,) cos 20° (.=9,) ’. tan 28! ~-- 2.36 (Old DDHB) 2, 2.38 (New DDHB) ie, tan 20tan 20° = —1 Hence 26) values and 20 yalues obtained from Equation 2.34 (Old DDHB) or 2.36 (New DDHB) for principal planes differ by 90°, In other words the planes of maximum shearing stress, are at 45° to principal planes. i¢., the planes of maximum shearing stress will at @, + 45° and @, + 135° Equations 2.36 (Old DDHB) or 2.38 (New DDHB) can be represented diagramatically by Fig. 1.34 in which (o,-0,) +4%3, Fig, 13436 Design of Machine Elements -| Substituting these cules in Equation 2.31 (Old DDB) or 2.33 (New DDHB), Tag 27 lo) +4 ~-2.39 (Old DDHB) 2.37 (New DDHB) 6, Fig. 135 1.8 TWO DIMENSIONAL (BI-AXIAL) STRESS FIELD [VTU, DEC.2008/JAN.09, MAVIJUNE 2010, DEC.2010] In most of the cases, the machine members are subjected to combined loading. In such cases, the design is based on the principal stress. The Fig, 1,36 shows an clement under a two dimensional stress field. 6, and 6, are the direct normal stresses and 1, is the shear stress. As explained earlier, the principal stresses can be obtained by the relationsIntroduction $$ $ $$ $$$ @i i i@_ i i@iai—_—_— 37 49; is the maximum value of principal siress and 6, is the minimum value of principal stress. 49, tt —_ i Fig. 1.36 Direct normal stress (Tension or Compression) due to bending or axial load or the combination of two 1 normal stress (Tension or Compression) in a direction normal 10 6, +, and, are the shear stresses, Since itis in static equilibrium s, = ,, Fora two dimensional stress system, the third principal stress, is zero, The maximum shear stress is equal to half of the greatest difference of any two of the three principal stresses. [ive considering the third principal stress which is zero in this case.) M-9: Oo; Zp and F wa is the largest among the three values of 1.9 THREE DIMENSIONAL (TRI-AXIAL) STRESS FIELD (VTU, DEC. 08/JAN.09, MAYIJUNE 2010, DEC. 2010] The Fig 1.37 shows a general three dimensional stress element, The three normal stresses 0, and 6, are positive (° Tensile) and the six shear Stresses Ty TT», and f,, are also positive,bnteduction 39 In the absence of shear stress, 6, 6, and 6, ate the principal stresses for the element, The relationship between the normal stresses and norinal strains in the x, y and z directions are, E Trost +E, +E, +e) E 6, = Gapiaall + ME, +VE,+e)1 E Tewlinay +e, +0, +6)) Sarcpienie tensa where B = Modulus of elasticity G = Modulus of rigidity 1 = Poisson's ratio, Y= Shear strain BIS system of Designation () Grey cast iron is specified by the symbol FG followed by the tensile strength in Nemm* (i), Steels which are standarised on the basis of their tensile strength without detailed chemical composition are specified by «wo ways. (a) A symbol Fe followed by the minimum tensile strength in N/mm. (b) A symbol FeF followed by the minimum tensile strength in N/mm’ i) Plain carbon steel consists of three quantities. (@)A figure indicating 100 times average percentage of carbon (b) Lewter C (©) 10 times average percentage of manganese. (iv) Unalloyed free cutting steels consists of five quantities, (8) A figure indicating 100 times the average percentage of carbon. (b) Letter C (©) 10 times the average percentage of manganese. (@) A symbol S, Se, Te or P, depending upon the element present. (©)A figure indicating 100 times the average percentage of the above element. (v) Alloy steel (a) A figure indicating 100 times the average percentage of carbon. (b) Chemical symbol for alloying elements each followed by the figure f Percentage content multiplied by a factor.40 Des of Machine Elements - | Elements Mukiplyingfactor Cy, Co, Ni, Mia, a Siané W Al, Be, ¥,Pb, Ca 0 Nb, Ti, Ta, Zr and Mo PSN 10 (ci) High alloy steels consits ofthe following quantities (@) ALeterX (b) A figure indicating 100 times the average percentage of carbon (©) Chemical symbo! of the alloying element followed by its average percentage content rounded vale (@) Chemical symbol to indicate « specially added element to attain desired properties. Identity the following engineering materials giving specifications, [VTU, July 2012} () FG350 (i) FeE 300 (ii) 458 Gv) 35C12Pb16 (s) 20Cr8Mo4 (i) IGNI3C-2_—— il). X20Cr1BNi2 () FG350 — Grey cast iron with an ultimate tersile strength of 350 N/mm? Gi) Fe 300 — A steel with a minimum yield strength of 300 N/mm? ii) 45C8. + Plain carbon stee! with 0.45% carbon and 0.8% manganese iv) 35C12Pb16 —> A free cutting steel with 0.35% carbon, 1.2% manganese and lead 0,16% (8) 20Cr8Mo4 + An alloy steel with 0.20% carbon, 2% chromium and 0.4% molybdenum, (vi) 16NI3Cr2 > An alloy steel with 0.167% carbon, 1,0% of nickel and 0.5% chromium. (vii) X20CrI8Ni2. > High alloy steel with 0.20% carbon, 18% chromium and 2% nickel Element subjected to uniaxial stress Example = 1.1 A tension member is formed, hy connecting two wooden scantlings with glue, each ‘50 mm x 100mm at their ends, which are cut at an angle of 60° as shown in the Fig, 1.38. The member is subjected to a pull F, Calculate the safe value of F, if the permissible normal and shear stress in the glue use are 3 Nimm? and 2 N/mmy respectively. Data: 3N/mm? 2N/omn? 6) ‘AreayA = 50100 = S000 mm? bso: Solution ‘Angle of joint with normal, = 90 -60=30" Fig, 138 Normal stress onthe incined plane, = 0, os - Bina ponee 100830 —2.13(NewDDHB}in 2.1 (0k DDEB), 2,14 New DDHB) Be SE sin(2 x30) [Postive since endsto produce ey rotation] 2G, = 4619 Nun "The lesser among these two values will be the safe stress Safe stress 6, = 4 Nim F Direct stress along x-axis 6, = x 21) P 5000 1. F = 20000 N = 20kN o.Safepull,P = 20KN Ley 4 = Element subjected to biaxial stress Example : 12 {A point ina strained material fs subjected (oa tensile stress of 500 N/mm* and 300 N/m in two mutually perpendicular planes. Calculate the normal, tangential, resultant stress and its obliquity on plane making an angle of 30° with the axis of minor tensile stress. Also find the maximum shear stress. Data: 9, = SOON/mm (Tensile) 6, = 300N/mm? (Tensile) 0 = 30° Solution : Asis of minor tensile woes g Minar principal plane Major priacipal oa Anis of major tensile tess Y 542 Design of Machine Elements - | Nonmal stress on plane BE 6, 0x28 —~226(OMMDDHB) ~~ 2.28 (New DDHB) 100+ 300 2 % esa “Tangential of Shear stress on plane BE 1, = > sin26 227 (ODDHB) (Negative sign indicates, tends to produce ow rotation) ~-2.20(NewDDHB) 500 ~300 awe Resultant suess on plane BE 0, = Jog +1] =y/430"+(-866)" =458.26N/mm? % 366 Resultant stress's direction or obliquity @= wr g) = tar" gq. sin 2x20) =~866N/oumn? © = 10893° (As shown in Fig. 1.39) 500-300 Maximum shear se Tyy = =-100NAam? (Negative siga indicates «,,, tends to produce ew rotation) Example :1.3 ‘The principal stresses at a point in a bar are 200 N/mm? (tensile) and 100 N/mm (compressive). Determine the normal, tangential, resultant stress and its direction on. plane incined at 60° to the axisof ‘major principal stress. Also determine the maximum intensity of shear stressin the material at the point, Data: 6, = 6,= 200N/mm? (Tensile) ©, = 6,= 100 N/mm? (Compressive) Figet.40 Inclination of plane BE with normal@ = 90-60=30°too $$ $i$i$i$i i iii ar 0820 ~~ 2.26 (01d DDHB) Normal stress on plane BE 0, = > 2.28 (New DDHB) = BOS , BO oa) Sete Asians os —-227;0upoH®) ~-- 2.29 (New DDHB) (Negative sign indicates ¢, tends to produce ew rotation) 200+100 2 Rosullan stress on planc BE.o, = yiog+g = yi25*+(-1299)° = 180.28 N/mm? ‘The incination of resultant stress with the normal of the inclined plane ts 1299 = tar! B= aw Bs sin (220) =~ 129.9N/nm? 1° (As shown in Fig. 1.40) 00+ 10 2 ‘Maximum shear stress 150 Nim? (Negative sign indicates r,,, tends to produce ew rotation) ‘Element subjected to uniaxial stress with simple shear Example: 1.4 A point in a plate grideris subjected to a horizontal tensile stress of 100 Nimm:? and vertical shear stress of 60 N/mm”. Find the magnitude of principal stresses and its location, Dia: ©, = 100mm? 5, = 60Nfmn? Solution: i 5, Major principal eres: o, = S + (bts =I, (es) +60? = 128.1 Nim (tensile) 2 Be 1S ae incpalstess 6, = S* — %) +t,44 $$ $$ __—_—_—— Dssign of Maciine Elements -1 8 30,194 oF 180+50.194 25,097" and @, = 115,097° Element subjected to pure shear Example : 1.5 ‘A point in a machine member is subjected to pure shear stress of magnitude 50 Nm. Determine (H Stresses acting on a plane inclined at an angle of 30° with respect to vertical plane (i) Principal stresses and their locations and (ii) Maximum shear stresses and its locations Data: Solution : a —} = Fig, 141 () Normal stress on plane BE ¢, = 1,sin26 - 50 sin (2% 30) = 43.3 Nim? 7,00829 50 cos (2% 30) = 25 Nimm* (Positive sign indicates 5, tends to produce cew rotation as shown in Fig, 1.41) (ii) Principal stresses 2.20 (Old DDB) 2.22 (New DDHB) 2.21 (Old DDHB) 2.23 (New DDHB) ‘Shear stress on plane BE +, ON/mm’ (Tensile) 50 N/mm? (Compressive) 2.22 (Old DDB) 2.24 (New DDHB) Location : i.e, Angles at which principal siresses act, ©, = 45° and @, = 135° 2.23 (Old DDHB),225 (New DDHB)Inoduction (i) Maximum shearstress ¢,,, = 41, =#50N¢mm* Angles at which maximum shear tess act @} = 0 and 64 = 90° — —-2.28(OldDDHB),2.27(NewDDHB) 45 2.24 (Old DDIB), 2.26 (New DDHB) Element subjected to biaxial stress with shear Example : 1.6 A point in a structural member subject to plane stress is shown in Fig. 1.42, Determine the following (@ Normal and tangential stress intensities on plane MN inclined at an angle of 45° i) Principal stresses and their direction (i) Maximum shear stress and the direetion of the planes on which it occurs. [V.T.U, July/Aug : 2002, Dec-08/Jan.09, June/July 2011, July 2012} | I I Data: 40MPa; 6, = -30MPa; t, = 25MPa 45° oa | Solution : = 30 MPa att on 40MPs<—[ = 10M? (i) Normal stress on plane MN, 6, c0320-+, sin —-230 (O14 DDHB) —2.32(NewDDHB) 30 008 (2245) +25 sih (245) =20 Nim? ‘Shear stress on plane MN, , in20-+1,, cos20 -231 (OMDDHB)4% Design of Machine Elements - oy OE sin) 425 08 (2945) = 35 Nn? (Nepuive sign indicate §, tends to produce ew rotation) —221NewDDHR) | (i) Maximum principalswess 0, = 2 + (5 Jee —2.32@0MDDEB) i " 2M (NewDDHB) + ) +d, —-2330MDDHB) | 235 (NewDDHB) _ 38.01 16mm? (Compressive) | ae ree x gai oral segs 1 (2x25, ---2.34(0Ml DDHB) 2,36 (New DDHB) 6. 8, = 17-769" and 0, = 107-760" eet 6, ii) Maximum shearswess —t,, =2( ) +, ~-=2.85 (Ol DDE) 2.37 (NewDDHB) y +25? = 2430116N'mm? Location : Angles at which maximum shear suess act | = 0,445 and 03 = 0,+135 28} = 17.769+45 = 62.769" ond @y = 17,7604135 =152.760° oR Anges ch masimmste te ne, = 5n( S22 |= f ($2238) = -27.231" and@ 3 =62.169" (783 = 0; +90)er Intocucton: a7 Example: 1.7 ‘A rectangular bar of section 50 mm 25 mm is subjected to a tensile lond of 25kN. Determine the ‘values of normal and shear stresses on a plane 30° with the vertical, Also calculate the magnitude and direction of the maximum shear stress. [VTU, Dec, 08/Jan. 2009] Data: F= 25 kN =25 x WN; 6 =30° D G F c Cross-sectional sreaof the bar Solution: 30° J 25kN Suess plane ER @, =~ = D € e =A 1250 aaa ‘Normal stress onthe inclined plane ©, = 0, c05'6 --2:13(DDHB) = 15 Némm $ sin 20 —~2.14(DDEB) —217(00HB) F10N/mm? All planes inclined at 45° tothe axis of pul are subjected to maximum shear stress, Example: 18 ‘The state of stress ata point ina strained member isshown in Fig. 44, Thettensile principalstress isknownto be 84 Nim Determine; (1) Maximum shearing stress atthe point and orientation ofits plane (i) shearing stress, IVTU, May/June 2010] SNim? Pig. dd48 Solution (i) Shearing stress t Design of Machine Eiements-{ Tensile principal stress 6, ie Shearing stress t,, = 49.356Nimm? (ii) Maximum Shearing stress and its planes Sy \ ) #49316" = 565 Nimm? 4 Angle at which maximum shear stress acts aaa (astss) = =14.563" and, = 75437" (+ 6, = 90+ 6)) Example : 1.9 ‘A pointin a structural member subjected to plane stress is shown in Fig. 148. Determine, (Normal and tangential stress intensities on plane EF inclined at an angle of 20° (i) Principal stresses and their direction ii) Maximum shear stress and the direction of the planes on which it occurs. 90MPa 5OMPa 140MParc {ned ution —$_$_$_$_?_?____ a Data: 6,=140 MPa zo, =90 MPa, ¢, = 50 MPa30=30" Solution : i) Normal stresson plane KF,9, 0520 +7, sin2@ —- —2.30(0MIDDHB) 3 ee a +( us 7 2) (230) +500(2 30) = 1708 Nim? —1.32(NewDDHB) 8,79, Shears onplane ER, = {222°} sn0 + s,c020 —231(0ap011) = (a ia 30 + 5.n(2%20) «+838 Nima? 133 (NewDDHB) (4ve) sign indicates +, tends to produce cew rotation ERG (i) Maximum principal stress c, minty —224(NewDDHB) 0, f W020) +0 =1709 Nios? —2304DDHB) ‘Minimum principal suess ©, 235 (Old DDHB) r a = 1079) (2) +50? = 501 Ni 233 NewDDHB) Location: Angles at which the principal stresses act Le bel Soba ean( 2255) Site Gaarag —236(NewDDHB) 31.72 and 6, 1.72.490=121 72" i) Maximum shear 0088 Tyg = 235 (O14DDHB) --2.37(NewDDHB}50 Location: Design of Machine Elements -| Angle at which maximum shear stress act @ |=, +45 and @, +135 1.72445 = 76,72° and 0) = 31.7212: oR +8, 66.72" Angle at which maximum shear stress acts sine and @ are 90° apart 2.38 (New DDHB) f @, = ~13.28° and €, 6; +90°=—13,28+ 90" 76.725 Example : 1.10 Direct stresses of 120 N/mm? (Tensile) and 90 N/mm’ (Compressive) exist on two perpendic lanesat a certain point in a body. They are also accompanied hy shear stress on the planes. The greatest Principal stress at the point due to theseis 150 N/mm’, Determine, @ Magnitude of shear sess on the wo planes G_ Mgximum shear stses a the poin. Data: * 6, = 120Nimm: (Tensile);6, = 90 N/mm (Compressive), 6, = 150 Nim? Sotution : (Magnitude of shear stress ‘Maximum principal stesso, iy +24 (New DDB) 1 2 : 3 a a 150 = +0, 232 (Old DEB) Shear stress, = 84.853 Nim? i) Maximum shear stress Maximum shear stress, = 235 (OMDDHB) + (Ey eta! i a 4135 Ninn? 2.37 (New DDEB)kx {nfo 0 —$— $$ A A i Example : 1.01 ‘The state of stress in a two dimensionally stressed body isshown in Fig. 1.46. Determine, @ Principal stresses and their direction i) Maximum shear stress and their planes. goMPa 6OMPa 6OMPa 120MPa ‘6OMPa somPa Fig, 146 -120 MPa 36, 80 MPa ; 7, =~60 MPa Solution : () Principal stresses and their direction Maximum principal suess 0, 2:34 (NewDDHB) = 120-80 , [/-120+80)" at ) +(-60)? ——.2324016 DDH) 36.154 Nama (Compressive) +s pias; [ieee ya = 163.246 Nén (Compressive) Minimum principal stesso, 34 (New DHE) )+Ca? 232/01 pap)82 Design of Machine Bement -| Locatio Angles at which principal strestes act, Qty —-234(OMDDHB) 236 (NewDDHB) (i) Maximum shear stress —-2.35 (OM DDHB) 37 (New DDHB) 120480 2 } +(-60)® =+63.246 Némm! Location [issih 2 @)=38.7825 + 45=80.7825" and 0, = 35.7825 + 135= 170.7825" Angle at which maximum shear stress acts 0 where 6, and 0, are 90° apart 38 (New DDHB) 20480) te da = “FH (Se) =9.2175° and 6 =6, + 90° ==92175 +90" = 80.7825"4 53 REVIEW QUESTIONS Sketch the stress-strain diagram for the following materials : ') Medium Carbon structural steel ii) Alloy steels, iii) Cast iron iv) Rubber v) Aluminium VTU, Jan/Feb 2004 Sketch the stress-strain diagram for a ductile material subjected to tension. Explain the significance of salient points VIU, Jan/Feb 2006, VIU, July/Aug. 2003, Aug. 2001 . Draw the stress-strain curve for mild steel and cast iron. Name the salient points, YTU, Feb. 2002 Briefly discuss factors influencing the sclection of suitable material for machine element VIU, July/Aug 2005, VTU, Jan/Feb 2005, VU, March 2001 BU Feb, 96, Feb. 97 5, Briefly discuss three dimensional (tri-axial) stress field and stress tensor, 6, Explain with examples, the importance and adoption of "standardisation in design calculations" BU Aug, 1995 . What are the important mechanical properties of metals? Explain each of them briefly. 10, i. 12. 13, 14, BU March/April 1999 Explain briefly the six steps involve in the design procedure Define the terms ; Principal planes and principal stresses VIU, Jan/Feb 2006 Define the terms ; stress, strain, clastic limit, Young's, modulus, lateral strain and Poisson's ratio On the rectangular stress element show the triaxial stress components and the corresponding stress tensor. VIU, Jan/Feb 2004 Define standardisation, State the standards used in machine design. VU, Jan/Feb 2005, 8) Draw the stress strain diagram and name the salient points for the following materials i) C-60steel ii) Cast iron FG 200 b)_Onithe rectangular stress element show the triaxial stress components and the corresponding stress tensor TU, July/Aug 2004 a) List the factors which govern the selection of a maierial for « machine component, b)_ Define standardisation. State the standards used in machine design. ¢) A barof 50 mm diameter fixed at one end is subjected to a torsional load of 1 KN—m in addition to an axial pull of 15 KIN. Determine the principal stresses. VIU, Jan/Feb 200584 15, Design of Machine Elements -1 . a) Discuss factors to be considered for selection of an appropriate material for a machine ‘element in the design process. VTU, July/Aug 2005 16. A machine clement in the form of a cantilever beam is made of a red of circular eross section ‘with @ span of 800mm, The material of the rod is carbon steel C30, Determine a safe value for 4 transverse load that falls on to the free end of the beam from a height of 25mm, if the ameter of the rod is 40mm. Use a value of 2.5 for the factor of safety. VTU, July/Aug 2008 17, a) Draw stress-strain diagram for a ductile material subjected to tension, Explain the significance of salient points b) Explain principal planes and principal stresses. VIU, Jan/Feb 2006 . a) Describe the material composition and properties of the following i) SAE 1045 and ii) 20 Cr 18Ni 2 steels b)_ Define factor of safety. Explain its use YTU, Jan.JFeb., 2006 a) Draw the stress strain diagrams for a ductile material and a brittle material and show the salient points on them. VTU, July 2006 a) Explain the factors, which given the selection of a material for a machine component. VU, Dec,, 07 / Jan, 082 DESIGN FOR STATIC AND IMPACT STRENGTH 24 STATIC STRENGTH ‘The standard tensile test results are used to obtain a variety of characteristics and strengths thatate used in design. Fig. 2.1 shows a typical tension test specimen. Some ofthe standard values used for d are 2.5, 6.25 and 12.5 mm, Similerly some of the common standard gauge lengths (/) used are 10, 25 and 50mm. When the specimen is mounted in the testing machine and slowly Jaded in tension, the load and the corresponding strain are recorded. Finally the test results are ploted as a stress-strain diagram. It is already discussed in article1. All the stresses and strengths defined by the stress-strain diagram in Fig 1.13 and similar diagrams are known as engineering, sesses and strengths or nominal stresses and strengths, All strengths are treated as absolute quantities. Fig. 21 2.2 STATIC LOAD Static loads are those which are applied to a structure gradually increasing from zero to its final maximum yalue. After reaching the final value, the load does not change in magnitude or direction or point of application with time and hence the acceleration oceurring can be neglected,55 Design of Machine elements «| 2.3 SIMPLE STRESSES Stresses produced by shear, tension and compression are called simple stresses when they are considered independently, A simple stress is considered to be distributed uniformly over the cross-section of the part on which the force is applied. ‘Axial load ‘Simple tensile load ee eveatercel —ik-ae F - Tense sesso = Comprenivesteu a= © A= Area of cross section of member Fig. 2.2 (a) Direct shear load yi x Single shear lond Double shear load oN re ref i V, Ler ref Ler = Y F Shear stress T= 3. A= Areaof cls of rivet Shear sess t= 95 Fig, 2.2 (6) 2.4 COMPOUND STRESS Stresses produced by torsion and bending are termed as compound stresses, because torsion and bending produce normal and tangential stresses in the same plane simultaneously. 2.4.1 Torsional stress + ‘The stress produced in a member twisted by a couple is pure shear, but its intensity on any fibre depends on the distance of the fibre from the center line of twisted member.Design for static ancl impact Strength 87 24.2 Torsional strength : ‘Torsional strength is defined as the torque per unit maximum shear stress. M, Torsional strength = “+ where M, = Torque and = Maximum shear stress 24.3 Torsional rigidity : tis the torque required to produce unit angle of twist in a specified length of shatt. M, ++ Torsional rigidity = “5° 2.44 Torsional flexibility: Itis the reciprocal of torsional rigidity, which is equal to the angle of twist per unit torque. 2.45 Polar moment of inertia : ‘Moment of inertia about an axis perpendicular to the plane of an area is known as polar ‘moment of inertia, ‘The general expression for torsion is M_ Got pee ~~ 2.50 (Old DDHB) where, M, = Applied torque in N.mm Te Polar moment of inertia mm Modulus of rigidity Nm? Angle of twist in radians Length of shaft in mm Radius of shaft in mm Maximum shear stress N/min? N 9550 > where M, in N-m ~ 2.51(a) (Old DDB) 2.87(b) (New DDHB) Power in kW ‘Speed in rpm. m J = 35 «* For solid circular shatt r = Zaj-a} ‘rcular shat 3a (td 4) For hollow circular shaftDeson of Machine Elements -| d= Diameter of solid shaft | Outer diameter of hollow shaft Inner diameter of hollow shaft. ~~~ Table 2.1 (Old DDHB) Ur = Jie= Polar section modulus ——- Table 2.2 (New PDHB) ‘The assumptions made while deriving the general expression for torsion are, (@ The material of the shaft is homogenous and isotropic (i) The twisting slong the shaft is uniform (iii) The shaft is uniform circular cross-section through out (iv) Normal cross-sections of the shaft which are plane before twist remain plane after twist (9) Material of the sha‘t follows Hooke’s law, 58 2.4.6 Bending stress : A beam is a structural member on which a system of external loads acts at right angles to its longitudinal axis. Due to these external loads, bending moments and shear forces ae setup at any point along the length of the beam. Hence the beam has to resist the action of bending moment and. shear force. The longitudinal stress produced at any section to resist the bending is known as the bending stress or flexure, 2.4.7 Simple bending or pure bending = When a beam is bend due to the application of constant bending moment without being subjected to shear or torsion or axial loads, then itis said to be in a state of pure bending or simple bending, ‘The general expression for bending is, este = ---- 2.52 (Old DDHB); 2.90 (New DDHB) = Maximum bending momemt in Nmm [= Moment of Inertia, mm* 6 = Maximum bending stress, mm’ © = Distance of neutral axis from the extreme fibre in mm E = Modulus of elasticity, Némm? | R = Radius of neutral layer or Radius of curvature in mm ‘The product El is called the flexural rigidity of the beam. Ec Bending stress o = “@-. This equation is called flexure formula. ‘The assumptions made while deriving the general expression for bending are, (i) The beam is subjected to pure bending. (i) The material of the beam is isotropic and homogeneous.Design for Static and impact Stength 69 (iii) Plane section remains plane even after bending. (iv) The beam is initially straight and every layer of it i free to expand or contract. (®) The value of Modulus of elasticity is the same in tension and compression. (iy The beam material is stressed within clastic limit and thus obeys Hooke's law. (vil) The radius of curvature of beam is very large when compared to its depth. 2.4.8 Section Modulus Section modulus is defined as the ratio of moment of inertia of a section about the neutral axis {othe distance of the outer most layer from the neutral axis. It is denoted by Z. L {= Tible 2.6 (Od DDHB); Table 2.7 (New DDEB) Forsolidcircularshatt, 1 = ~ qtande= 4 5 solid circular shat, ay tandc= , Kata! Forhollowcireularshait, 1 = Z(d}—d) and 2.5 WORKING STRESS : When designing machine parts, it is desirable to keep the stress lower than maximum or ultimate siress at which failure of the material takes place. This stress is known as working stress or design stress o allowable stress, 26 FACTOR OF SAFETY (F.0.S) Its defined as the ratio of the maximum stress to the working stress. For ductile material, here the yield point is clearly defined, the factor of safety is based on yield stress For simple tension or compression, ‘Maximum stress FOS = Working or design stress Yield point stress (6, FOS. = So ree "Working stress (a) For pure shear Yield point stress in shear (, FOS “Allowable or Maximum shear stress (Tuy) For brittle material, where the yield point is not well defined, the factor of safety is based on uukimate stress,60 Design of Machina Elements -| For simple tension Ultimate sressin tension (6,.) ‘Working tress in tension (a,) FOS = For simple compression Untimate stressin compression (6,.) FOS = Working stressin compression (6) Since the ultimate stress in tension and compression are not equal in brittle material, itis necessary to have separate equations for the factor of safety in tension and in compression. 2.6.1 Discuss factors influencing selection of appropriate value for the factor of safety ¢VTU. Mareh 2001, Feb 2003) ‘The selection of a proper factor of safety to be used in designing any machine component depends upon number of factors, They are, (@) Variation in material properties (i) Type of loading and stress. Effect of machining or forming processes or mode of manufacture iv) Effect of time and environment in which the device is expected to operate. (©) Effect of size in material strength properties. (vi) Effect of wear upon the functions and life of a machine member. (vii) Specific requirements for life and reliability. (viii) Effect of heat treatment upon the physical properties of material (x) Overall concem for human safety. 2.7 ECCENTRIC LOADING An external load whose line of action is parallel but does not coincide with the centroidal ‘of the machine component is kiown as an eccentric load. It is shown in Fig 2.3, The distance the centrodial axis ofthe machine component and the point of appliction of load is called eccentricit and is denoted by ‘e'. Due to the eccentric load the stresses produced in the body are, () Direct stress due to F Gi) Bending stress due to the bending moment or couple F.c Divet stress @ = 5 (Comprowive) Bending moment M, = Fe M Bending stress at the edge AB = ae (Compressive)Design for Static and impact stengtn 61 Bending stress at the edge CD Te (Tensile) Combined stress at AB a[x >| Mac (Compressive) F Combined stress at CD ey (Tensile Symbols ~ Fore N — Ares of cross-section, mm? Moment of Inertia, mm ~ Polar moment of inertia, mm* ‘Working or Allowable or Design normal stress, N/mm? [Tensile or Compressive or Bending] ‘Working or Allowable or Design shear stress, N/m? ‘Maximum bending moment, N-mm |, ~ Maximum torque, N-mm G ~ Modulus of rigidity, N/mm? E — Modulus of elasticity, N/mm? Qunes t M, M,62 Design of Machine Elements =| Yield point stress, N/mm? Ultimate point stress, N/mm? ‘Yield stress in shear, N/mm? +t, — Ultimate stress in shear, Némm? FOS orn — Factor of safety Example : 2.1 A plain carbon steel of grade 4SC8(c,,=360 MPa) is subjected to tensile oad of 60 KN. Calculate the diameter of the rod, using factor of safety = Diameter of rod d= 25.23 mm = 30mm [From Table 14-6 (New DDHB)} Example : 2.2 Aflat bar shown in Fig 24 is subjected to i compressive load of 100 KN. Ifthe allowable stres for the ‘material ofthe bar is 100 N/mm’, determine the thickness of bar. Data: F=100 KN = 10010" N (Compressive) ‘= 100 N/mm (Compressive) Solution ; Cross sectional area A= 100 kN —>} 100 kN 100. mm — ! 7Design for Sialic and impact stiengin 63 >is Forcompressive load, allowable siress 0 = 100%10" 1001 + Thickness of bar! = 10mm Example : 2.3 ‘Two round rods are joined by means of a knuckle joint as shown in Fig 2.5. Determine the iameter of rod and the diameter of knuckle pin, ifthe rod carrying a tensile load of SOkN and the allowable stresses for the rod and the pin are 100 N/mm! in tension and 4S N/mm in shear. Data: Load = F = 50 KN = 50 x 10° N (Tensile) Allowable stress in tension o = 100 N/mm? Allowable stress in shear t= 45 N/mm! Solution: 100 Fig. 25 Design of rod : The rod is subjected to tensile load ++ Allowable tensile stress inthe rod. = —~ 50>10° ie, 100 = +. Diameter of rod D = 25.23 mm = 30mm [From Table 14.6] (New DDHB) Design of knuckle pin : The knuckle pin is subjected to double shear,Design of Machine Elements «| 6 50x10” ia Ae ae <2 Diameter of knuckle pin d = 261mm = 30 mm Example : 2.4 Fig 2.6 shows a C.A, Link. The link material has maximum normal stress of 65 MPa. Check the design to transmit a steady tensile load of $0 KN and comment on your recommendation (BU, April 1995) ta B A SECTION A.A Fig. 26 Data: ‘Tensile load F = 50 KN = 50 x 10° Allowable normal stress 6 = 65 MPa = 65 Nimm* (Tensile) Solution : () Consider the section at B-B Cross sectional area at B-B = 20% 4 Induced tensile stress at B-Bo,, = = 55:56 Nimm?< 0, (ii) Consider the section at A-A Cross sectional area at A-A = (75 x 20) ~ (40 x 20) = 700 mm F _ sox10? laced tensile stress al A-AG,, = = = im Induced tensile stress al A-AG,,. = = Ty —= 7143 Nimm? > Gy, Since the induced tensile stress at section A-A is greater than the maximum normal stress (i.e, 65 N/mm? Jo the link material, the ink cannot be able to transmit the steady tensile load of 50 KN.Design for Static and Impact Strength 65 Example : 2.5 ‘A steel saw blade Imm thick is bent into an are of a circle of $00. mm radius. Determine the ‘esural stress induced and the bending moment required to bend the blade, which is 15 mm wide, ‘Take B= 210GPa. (VTU March 2001) Data B= 210 GPa =210 x 10° Nimm* Solution : ‘The general expression for bending is Me oS = 20X10" 695— 210 Nima? a ees es ee it 00) Example : 2.6 ‘A beam of uniform rectangular cross-section is fixed at one end and carries a load 1000 N at a distance of 300 mm from the fixed end. The maximum bending stress in the beam is 89 Nim’ Find the width and depth of beam. If depth is twice that of width. Data: F=1000N;_ 0 = 80 Némm*s Solution : = 300: mm; h = 2b [F = 1000 N Fig. 2.7 From Table 2.7 (Old DDHB); 2.8 (New DDHB) for Cantilever beam ‘Maximum Bending moment M, = F/= 1000 x 300= 3 x 10" Nan06 Design of Machne Elements From Table 26 (Old DDHB); Table 2.7 (New DIB) for rectangular eros section ba? _ b¢2b)! oh The general expression forthe beng is For rectangular c/s, —-2.52(Old DDHB);2.90 (New DDHB) ‘Take widthof beam b © Depthof beam h Example : 2.7 Design a shaft to transmit 10 kW at 2040 rpm. Itis made of 37C1S steel (o,, = 431.5 MPa), Deflection in the shatt is not to exceed 1" per meter length Data: N: Solution : Assume FOS=3 OW: 2000 rpm ” per metre length;o,,= 431.5 N/mm? 5, _ ass ae Nema? Fos 2g = SBN’ Allowable stress in shear =0.50=0.5 x 143.83=71.92Nmam* From Table 2.10(New DDH) for carbon steel, G=79G.Pa= 79x 10° Nim? ++ Working or Allowable normal stress Terme = 990 nce Minin -2sia4po1 seco oe hiaNam AAT Nee 9550 x 10° a -ATISO N- 880930 39, sam 8 am he gna neon rte i 2s oADEH 2 S604 DEK For strengthDatign for Static and Impact Strength ‘7 ve, A780 _ 1192 Bees ces eas Forsitiess osigiiy 1000 sd = 24.37 mm, say 26mm [From Table 14.6New DEB), - Diameter of the shaft d = 25mm (Select the bigger value} Example : 2.8 ‘Design a spindle of milling machine to transmit 1SkW at 1000 rpm. The angular twist is not to exceed 05° per metre length. The material for the spindle is 45C8 stccl(¢, = 360 MPa). The outside diameter of | the spindle istwice that of inside diameter. Take factor of safety = Data: N=ISKW; 0 = 1000 rpm; Setation = 0.5" per metrelengih; dj=2d; FOS =250,,=360 N/mm 360, Fos 2 Allowable stress in shear t= 0.50 = 0.5 x 180=90 Nim? From Tuble2.10 (New DDHB) forcarbon steel G = 79G-Pa=79 x 10° Ninn? ‘ Working orDesign normal stress 51(@) (Old DDB) '87(b) New DDHB) N Torque M, = 9350%" where Min Nan oss0n10%™ soc aN 9550x1095. = 7000 43250 ‘The general expression for torsion is, -+250 (Old DDHB 2.86 (New DDHB)68 Design of Machine Elements =| For strength i 143250 cs (a3 -05*as) . a (From Table 14,6New DDHB) For stiffness or rigidity M where @ in radians and = 1m-=1000mm 19210 x(05x,%) 180) 143250 (at -osta}) cd 2 sd, = 3876 mm_ 40mm [From Tuble 14.6 (New DDHB)] Outer diameter of the spindle d,= 40 mm [Adopt the bigger value] Inner diameter ofthe spindle d,=20mm (1. d,=24i) smple : 2.9 Determine normal tressesat the extreme fibres on the ross section AA of a clamp loaded as inFig,2.8(a). P= 80 EN VIU, Jame Solution: Here the applied load isan eccentric load since the load is acting parallel to the cg axis and away’ it, Due to the eccentric load the stresses produced in the body are, Direct stress due to P and a) Bending stress due tothe bending moment of couple Pe.69 Design for Static and impact shength ‘Consider the cross section AA of the C-clamp as show in Fig, 2.8 (D) (ooean{#) enero soe!) (100 x 40)+ (40% 100) 1 re 280) Dinette fe =m Simm stance of NA from the outer most fibre = Eecentricty = Distance of eg from the load = 150 +55 I = Toral moment of inertia of the section about the cg ‘= Ml of section (1) about cg + MI of section (2) about cg 10040" 40 (100 x 40)( 55— = { nt { 7) A = Areaof cross section of the section =a, + 2, = (100 x 40) + (40 x 100) = 8000 mm Bending moment M, = Re=80 x L0°x205= 16.4 x L* Naum, Forthe givemoad, bending stress atthe inner fibre is tensile and outer fibre is compressive. Dicet stress is tensile trout. 3.967 10" mnt } [Os eoxsone 5)? POM, Combine stress at nner mest fibre 6, = Direct sess + Bening stress= 2+ OE sent gk nl © 80000" 1365710" ae ae70 ——________________ Design of Machine Elements - . P Myo ‘Combined stress at the outer most fibre 6, = Direct stress ~ Bending sess = 5 80x 107 16.4 10° x85 8000 13,967 x10 92 N/oumé (compressive) —91,9975 Nim? Example : 2.10 Determine the required thickness ofthe steel bracket atsection A-A when loaded asshown in Fig.29 in order to limit the tensile stress to 100 N/mm [VTU, June 2012] | so—-f 5000 Fig. 29 Solution ‘The given Toatl is an eccentric load. Therefore duc to this lead the body is subjected to (© Direct sress due vo F and (i) Bending stress due to Bending moment or couple Fe = Eccentricity [tis the distance ofthe load from the cg oF the section] = 50 mm Applied load F = 5000.N 2 Bending moment M, = Fe= 500% 50=25 x 10" N-mm ‘Area of cross-section at section A-A =50xh. Moment of inertia about the eg of the s Distance of NA from the extreme fibre * Combined maximura tensile stress atthe inner fibre = Direct tensile siress + Bending stress FMDesign for Static and impact Sirength —— $$$ 7 sooo , (25%104) Sox xs 2 ie, 100 = x25 5 h=7mm Hence the thicknoss required to limit the stress to 100 N/m 7mm Example : 2.11 A mild steel bracket shown in Fig. 2.10(a) is subjected to a pall of 10 kN. The bracket has 2 rectangular cross-section whose depth is twice the width. Ifthe allowable stress for the material ts 80 ‘Nimm?, determine the e/s of the bracket, F, =F sin 60 “<> y FRIOKN F, = Feos 60 (@) ) Data P= 10 kN = 10° N; 0 = 80 Nimm?; Solution : Resolving the given force into two components as shown in Fig. 2.10 (b) Vertical component F, = F c0s 60 = 10,000 cos 60 = 5000 N Horizontal component F,, = F sin 60 = 8650.254 N U0) Consider the vertical component : Bending moment due to vertical component My, = F, x 150 = 5000 x 150 =75 x 10" Nmm —@2 << Design of Machino torments -| Dee to this vertical bending momert, tensile stress is induced on the upper surface and compressive sures i induced om the bottom surface, (2) Consider the horizontal component : “The horizontal component of the given load is an eccentric loa Therefore duc to this load the see bracket is subjected to, (a) Direct stress due to F,and (b) Bending stress due to the Bending moment or couple Fe Bending momentduc t horizontal component = F,,© = 8660.254 x 200= 1732050.8 Nam = Eccentricity=200mm. stance of N.A from the extreme fibre = Direct stress due to F,, is tensile thro'out and the bending siress due tothe couple on the upper surface is tensile and botiom Surface is compressive. &. Combined stress on the upper surface ie, 0, = 2560284 , 17320508 "= gp TZ 3 4330127 , 25980762 10,5 yr tps (Tensile) ‘Total tensile strese on the upper surface o = 1125x10* , 4330127 | 25980762 +5, ie, 80 = ——> a b i b 37230762+4330127b oe oe ie, 8Ob) = 4930,127b + 37230762 ise, BY $4,126 b — 46538453 By trial and error method. o b = 36472 mm say 365mm + Width of bracket b = 36.5 mm Depth of bracket = 73mm (+: b=2b)Design for Static and Impact Stengih ————————._ 73 Beample : 2.12 Determine dimensions ofthe principal cross - section of the cast fron link shown in Fig, 21a). ‘The maximum tensile loxd is 37 KN. The stress values should not be exceeded 21 N/mm? in tension ‘and 84 N/mm? in compression. : = 4 Zh y At je—i!_ of

You might also like

• Design of Machine Elements-I by Das JBK

  

  No ratings yet

  Design of Machine Elements-I by Das JBK

  757 pages
• Machine Design

  

  No ratings yet

  Machine Design

  3 pages
• Design of Machine Elements-I by Das JBK 1

  

  No ratings yet

  Design of Machine Elements-I by Das JBK 1

  263 pages
• Pte Mag PDF

  

  100% (1)

  Pte Mag PDF

  68 pages
• Machine of Design PDF

  

  No ratings yet

  Machine of Design PDF

  788 pages
• MAK4462 Machine - Tools Lecture - Notes 2

  

  No ratings yet

  MAK4462 Machine - Tools Lecture - Notes 2

  68 pages
• Master Seal Product Range

  

  100% (1)

  Master Seal Product Range

  777 pages
• Solid Modeling Final - Manual-06!05!19 New by Mail

  

  No ratings yet

  Solid Modeling Final - Manual-06!05!19 New by Mail

  276 pages
• CH 3 Fa2018

  

  No ratings yet

  CH 3 Fa2018

  89 pages
• Creative Mechanism Design

  

  No ratings yet

  Creative Mechanism Design

  56 pages
• Force Analysis - PPSX

  

  No ratings yet

  Force Analysis - PPSX

  107 pages
• PDF 92 1

  

  No ratings yet

  PDF 92 1

  106 pages
• MD2 PDF

  

  No ratings yet

  MD2 PDF

  222 pages
• Manufacturing Processes - Iiprof. A.b.chattopadhyay, Prof. A.K. Chattopadhyay

  

  88% (8)

  Manufacturing Processes - Iiprof. A.b.chattopadhyay, Prof. A.K. Chattopadhyay

  618 pages
• MAK4462 Machine - Tools Lecture - Notes 3

  

  No ratings yet

  MAK4462 Machine - Tools Lecture - Notes 3

  126 pages
• Theory of Machinary-1 PDF

  

  No ratings yet

  Theory of Machinary-1 PDF

  258 pages
• ME 314 Design of Machine Elements (3-0-0-6) : Texts

  

  No ratings yet

  ME 314 Design of Machine Elements (3-0-0-6) : Texts

  9 pages
• JJ311 MECHANICAL OF MACHINE CH 3 Velocity and Acceleration Diagram

  

  100% (1)

  JJ311 MECHANICAL OF MACHINE CH 3 Velocity and Acceleration Diagram

  31 pages
• Question Papers - AMIE - Design of Machine Tools

  

  80% (5)

  Question Papers - AMIE - Design of Machine Tools

  34 pages
• Mechanics of Machines Tut

  

  100% (1)

  Mechanics of Machines Tut

  11 pages
• 4363 111 Machine Design I

  

  100% (2)

  4363 111 Machine Design I

  6 pages
• Bell Crank Lever

  

  No ratings yet

  Bell Crank Lever

  7 pages
• Dynamics of Machinery PDF

  

  No ratings yet

  Dynamics of Machinery PDF

  2 pages
• Edu Sae Instructor 2013 Eng

  

  No ratings yet

  Edu Sae Instructor 2013 Eng

  205 pages
• Mechanisms in Modern Engineering Design V1

  

  50% (4)

  Mechanisms in Modern Engineering Design V1

  632 pages
• Kinematics of Machinery

  

  100% (1)

  Kinematics of Machinery

  38 pages
• Introduction To Solid Modeling PDF

  

  100% (1)

  Introduction To Solid Modeling PDF

  50 pages
• 2 4-Kom PDF

  

  No ratings yet

  2 4-Kom PDF

  90 pages
• DTS Question Bank

  

  100% (1)

  DTS Question Bank

  21 pages
• Cad/Cam Manual

  

  No ratings yet

  Cad/Cam Manual

  83 pages
• Dynamics of Machinery: S.No Governors Flywheel

  

  No ratings yet

  Dynamics of Machinery: S.No Governors Flywheel

  87 pages
• CH 1 Intro

  

  No ratings yet

  CH 1 Intro

  40 pages
• Theory of Machine II

  

  100% (2)

  Theory of Machine II

  2 pages
• Measurement of Major Diameter & Effective Diameter

  

  100% (2)

  Measurement of Major Diameter & Effective Diameter

  9 pages
• MECA 332 Mechatronics Component Design: Week 8 Ps - Iv

  

  No ratings yet

  MECA 332 Mechatronics Component Design: Week 8 Ps - Iv

  19 pages
• Statement: Solution:: Problem 2-8

  

  No ratings yet

  Statement: Solution:: Problem 2-8

  1 page
• 2type and Number Synthesis

  

  No ratings yet

  2type and Number Synthesis

  9 pages
• Question Bank Strength of Materials: Hooghly Engineering & Technology College

  

  No ratings yet

  Question Bank Strength of Materials: Hooghly Engineering & Technology College

  25 pages
• Design of Machinery: Chapter 1 Introduction Summary

  

  100% (2)

  Design of Machinery: Chapter 1 Introduction Summary

  9 pages
• MECH 2410 Final Presentation: Titled "Prototype CAD Files" and The Other Titled "Prototype DWG Files (PDF) "

  

  No ratings yet

  MECH 2410 Final Presentation: Titled "Prototype CAD Files" and The Other Titled "Prototype DWG Files (PDF) "

  17 pages
• 12ed11 - Advanced Machine Tool Design

  

  No ratings yet

  12ed11 - Advanced Machine Tool Design

  15 pages
• Machine Tool Design Chapter One

  

  No ratings yet

  Machine Tool Design Chapter One

  12 pages
• Finite Element Method Simulation Lab: Report On Tutorial Problems Submitted in Fulfillment of The Requirements of

  

  No ratings yet

  Finite Element Method Simulation Lab: Report On Tutorial Problems Submitted in Fulfillment of The Requirements of

  32 pages
• Design of Multi-Axis Welding Positioner With

  

  No ratings yet

  Design of Multi-Axis Welding Positioner With

  7 pages
• Cad Imp Questions PDF

  

  No ratings yet

  Cad Imp Questions PDF

  5 pages
• Homework 4 Solution

  

  No ratings yet

  Homework 4 Solution

  10 pages
• Machine Elements 1: Assignment 2

  

  No ratings yet

  Machine Elements 1: Assignment 2

  15 pages
• Dme Unit II Mech 30.06.12

  

  No ratings yet

  Dme Unit II Mech 30.06.12

  33 pages
• Unit 1. Fundamentals of Design Master b5

  

  No ratings yet

  Unit 1. Fundamentals of Design Master b5

  20 pages
• 2173408

  

  No ratings yet

  2173408

  3 pages
• Cam Mechanisms Pack

  

  No ratings yet

  Cam Mechanisms Pack

  28 pages
• Me6503 Dme Unit 2 Study Notes 2015

  

  No ratings yet

  Me6503 Dme Unit 2 Study Notes 2015

  27 pages
• 1 Design of Machine Tool Drives

  

  No ratings yet

  1 Design of Machine Tool Drives

  23 pages
• DOM Assignments 28062016 064421AM PDF

  

  No ratings yet

  DOM Assignments 28062016 064421AM PDF

  18 pages
• Machine Design II

  

  No ratings yet

  Machine Design II

  23 pages
• Numerical Investigation of Structural Design of Torsion Links in A Landing Gear Retraction Mechanism

  

  No ratings yet

  Numerical Investigation of Structural Design of Torsion Links in A Landing Gear Retraction Mechanism

  7 pages
• Unit - V Data Base in Computer Integrated Manufacturing

  

  No ratings yet

  Unit - V Data Base in Computer Integrated Manufacturing

  26 pages
• Assembly Drawing Examples PDF - Google Search4

  

  No ratings yet

  Assembly Drawing Examples PDF - Google Search4

  2 pages
• Integrated Mechanical Design Jan - 10

  

  No ratings yet

  Integrated Mechanical Design Jan - 10

  4 pages
• Lab Report Eet

  

  No ratings yet

  Lab Report Eet

  4 pages