MX80 3D Universal Edge

Router
Hardware Guide

Published: 2010-05-24

Copyright © 2010, Juniper Networks, Inc.

Juniper Networks, Inc.
1194 North Mathilda Avenue
Sunnyvale, California 94089
USA
408-745-2000
www.juniper.net
This product includes the Envoy SNMP Engine, developed by Epilogue Technology, an Integrated Systems Company. Copyright © 1986-1997,
Epilogue Technology Corporation. All rights reserved. This program and its documentation were developed at private expense, and no part
of them is in the public domain.

This product includes memory allocation software developed by Mark Moraes, copyright © 1988, 1989, 1993, University of Toronto.

This product includes FreeBSD software developed by the University of California, Berkeley, and its contributors. All of the documentation
and software included in the 4.4BSD and 4.4BSD-Lite Releases is copyrighted by the Regents of the University of California. Copyright ©
1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994. The Regents of the University of California. All rights reserved.

GateD software copyright © 1995, the Regents of the University. All rights reserved. Gate Daemon was originated and developed through
release 3.0 by Cornell University and its collaborators. Gated is based on Kirton’s EGP, UC Berkeley’s routing daemon (routed), and DCN’s
HELLO routing protocol. Development of Gated has been supported in part by the National Science Foundation. Portions of the GateD
software copyright © 1988, Regents of the University of California. All rights reserved. Portions of the GateD software copyright © 1991, D.
L. S. Associates.

This product includes software developed by Maker Communications, Inc., copyright © 1996, 1997, Maker Communications, Inc.

Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United
States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are trademarks of Juniper Networks, Inc. All other
trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners.

Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify,
transfer, or otherwise revise this publication without notice.

Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are
owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312,
6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785.

MX80 3D Universal Edge Router Hardware Guide

Copyright © 2010, Juniper Networks, Inc.
All rights reserved. Printed in USA.

Writing: Charissa Fleischer

Editing: Joanne McClintock
Illustration: Faith Bradford Brown

Revision History
May 2010—Initial release.

The information in this document is current as of the date listed in the revision history.

YEAR 2000 NOTICE

Juniper Networks hardware and software products are Year 2000 compliant. The Junos OS has no known time-related limitations through
the year 2038. However, the NTP application is known to have some difficulty in the year 2036.

ii Copyright © 2010, Juniper Networks, Inc.

END USER LICENSE AGREEMENT

READ THIS END USER LICENSE AGREEMENT (“AGREEMENT”) BEFORE DOWNLOADING, INSTALLING, OR USING THE SOFTWARE.
BY DOWNLOADING, INSTALLING, OR USING THE SOFTWARE OR OTHERWISE EXPRESSING YOUR AGREEMENT TO THE TERMS
CONTAINED HEREIN, YOU (AS CUSTOMER OR IF YOU ARE NOT THE CUSTOMER, AS A REPRESENTATIVE/AGENT AUTHORIZED TO
BIND THE CUSTOMER) CONSENT TO BE BOUND BY THIS AGREEMENT. IF YOU DO NOT OR CANNOT AGREE TO THE TERMS CONTAINED
HEREIN, THEN (A) DO NOT DOWNLOAD, INSTALL, OR USE THE SOFTWARE, AND (B) YOU MAY CONTACT JUNIPER NETWORKS
REGARDING LICENSE TERMS.

1. The Parties. The parties to this Agreement are (i) Juniper Networks, Inc. (if the Customer’s principal office is located in the Americas) or
Juniper Networks (Cayman) Limited (if the Customer’s principal office is located outside the Americas) (such applicable entity being referred
to herein as “Juniper”), and (ii) the person or organization that originally purchased from Juniper or an authorized Juniper reseller the applicable
license(s) for use of the Software (“Customer”) (collectively, the “Parties”).

2. The Software. In this Agreement, “Software” means the program modules and features of the Juniper or Juniper-supplied software, for
which Customer has paid the applicable license or support fees to Juniper or an authorized Juniper reseller, or which was embedded by
Juniper in equipment which Customer purchased from Juniper or an authorized Juniper reseller. “Software” also includes updates, upgrades
and new releases of such software. “Embedded Software” means Software which Juniper has embedded in or loaded onto the Juniper
equipment and any updates, upgrades, additions or replacements which are subsequently embedded in or loaded onto the equipment.

3. License Grant. Subject to payment of the applicable fees and the limitations and restrictions set forth herein, Juniper grants to Customer
a non-exclusive and non-transferable license, without right to sublicense, to use the Software, in executable form only, subject to the
following use restrictions:

a. Customer shall use Embedded Software solely as embedded in, and for execution on, Juniper equipment originally purchased by
Customer from Juniper or an authorized Juniper reseller.

b. Customer shall use the Software on a single hardware chassis having a single processing unit, or as many chassis or processing units
for which Customer has paid the applicable license fees; provided, however, with respect to the Steel-Belted Radius or Odyssey Access
Client software only, Customer shall use such Software on a single computer containing a single physical random access memory space
and containing any number of processors. Use of the Steel-Belted Radius or IMS AAA software on multiple computers or virtual machines
(e.g., Solaris zones) requires multiple licenses, regardless of whether such computers or virtualizations are physically contained on a single
chassis.

c. Product purchase documents, paper or electronic user documentation, and/or the particular licenses purchased by Customer may
specify limits to Customer’s use of the Software. Such limits may restrict use to a maximum number of seats, registered endpoints, concurrent
users, sessions, calls, connections, subscribers, clusters, nodes, realms, devices, links, ports or transactions, or require the purchase of
separate licenses to use particular features, functionalities, services, applications, operations, or capabilities, or provide throughput,
performance, configuration, bandwidth, interface, processing, temporal, or geographical limits. In addition, such limits may restrict the use
of the Software to managing certain kinds of networks or require the Software to be used only in conjunction with other specific Software.
Customer’s use of the Software shall be subject to all such limitations and purchase of all applicable licenses.

d. For any trial copy of the Software, Customer’s right to use the Software expires 30 days after download, installation or use of the
Software. Customer may operate the Software after the 30-day trial period only if Customer pays for a license to do so. Customer may not
extend or create an additional trial period by re-installing the Software after the 30-day trial period.

e. The Global Enterprise Edition of the Steel-Belted Radius software may be used by Customer only to manage access to Customer’s
enterprise network. Specifically, service provider customers are expressly prohibited from using the Global Enterprise Edition of the
Steel-Belted Radius software to support any commercial network access services.

The foregoing license is not transferable or assignable by Customer. No license is granted herein to any user who did not originally purchase
the applicable license(s) for the Software from Juniper or an authorized Juniper reseller.

4. Use Prohibitions. Notwithstanding the foregoing, the license provided herein does not permit the Customer to, and Customer agrees
not to and shall not: (a) modify, unbundle, reverse engineer, or create derivative works based on the Software; (b) make unauthorized
copies of the Software (except as necessary for backup purposes); (c) rent, sell, transfer, or grant any rights in and to any copy of the
Software, in any form, to any third party; (d) remove any proprietary notices, labels, or marks on or in any copy of the Software or any product
in which the Software is embedded; (e) distribute any copy of the Software to any third party, including as may be embedded in Juniper
equipment sold in the secondhand market; (f) use any ‘locked’ or key-restricted feature, function, service, application, operation, or capability
without first purchasing the applicable license(s) and obtaining a valid key from Juniper, even if such feature, function, service, application,
operation, or capability is enabled without a key; (g) distribute any key for the Software provided by Juniper to any third party; (h) use the

Copyright © 2010, Juniper Networks, Inc. iii

Software in any manner that extends or is broader than the uses purchased by Customer from Juniper or an authorized Juniper reseller; (i)
use Embedded Software on non-Juniper equipment; (j) use Embedded Software (or make it available for use) on Juniper equipment that
the Customer did not originally purchase from Juniper or an authorized Juniper reseller; (k) disclose the results of testing or benchmarking
of the Software to any third party without the prior written consent of Juniper; or (l) use the Software in any manner other than as expressly
provided herein.

5. Audit. Customer shall maintain accurate records as necessary to verify compliance with this Agreement. Upon request by Juniper,
Customer shall furnish such records to Juniper and certify its compliance with this Agreement.

6. Confidentiality. The Parties agree that aspects of the Software and associated documentation are the confidential property of Juniper.
As such, Customer shall exercise all reasonable commercial efforts to maintain the Software and associated documentation in confidence,
which at a minimum includes restricting access to the Software to Customer employees and contractors having a need to use the Software
for Customer’s internal business purposes.

7. Ownership. Juniper and Juniper’s licensors, respectively, retain ownership of all right, title, and interest (including copyright) in and to
the Software, associated documentation, and all copies of the Software. Nothing in this Agreement constitutes a transfer or conveyance
of any right, title, or interest in the Software or associated documentation, or a sale of the Software, associated documentation, or copies
of the Software.

8. Warranty, Limitation of Liability, Disclaimer of Warranty. The warranty applicable to the Software shall be as set forth in the warranty
statement that accompanies the Software (the “Warranty Statement”). Nothing in this Agreement shall give rise to any obligation to support
the Software. Support services may be purchased separately. Any such support shall be governed by a separate, written support services
agreement. TO THE MAXIMUM EXTENT PERMITTED BY LAW, JUNIPER SHALL NOT BE LIABLE FOR ANY LOST PROFITS, LOSS OF DATA,
OR COSTS OR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, OR FOR ANY SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THIS AGREEMENT, THE SOFTWARE, OR ANY JUNIPER OR JUNIPER-SUPPLIED SOFTWARE. IN NO EVENT SHALL JUNIPER
BE LIABLE FOR DAMAGES ARISING FROM UNAUTHORIZED OR IMPROPER USE OF ANY JUNIPER OR JUNIPER-SUPPLIED SOFTWARE.
EXCEPT AS EXPRESSLY PROVIDED IN THE WARRANTY STATEMENT TO THE EXTENT PERMITTED BY LAW, JUNIPER DISCLAIMS ANY
AND ALL WARRANTIES IN AND TO THE SOFTWARE (WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE), INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT. IN NO EVENT DOES
JUNIPER WARRANT THAT THE SOFTWARE, OR ANY EQUIPMENT OR NETWORK RUNNING THE SOFTWARE, WILL OPERATE WITHOUT
ERROR OR INTERRUPTION, OR WILL BE FREE OF VULNERABILITY TO INTRUSION OR ATTACK. In no event shall Juniper’s or its suppliers’
or licensors’ liability to Customer, whether in contract, tort (including negligence), breach of warranty, or otherwise, exceed the price paid
by Customer for the Software that gave rise to the claim, or if the Software is embedded in another Juniper product, the price paid by
Customer for such other product. Customer acknowledges and agrees that Juniper has set its prices and entered into this Agreement in
reliance upon the disclaimers of warranty and the limitations of liability set forth herein, that the same reflect an allocation of risk between
the Parties (including the risk that a contract remedy may fail of its essential purpose and cause consequential loss), and that the same
form an essential basis of the bargain between the Parties.

9. Termination. Any breach of this Agreement or failure by Customer to pay any applicable fees due shall result in automatic termination
of the license granted herein. Upon such termination, Customer shall destroy or return to Juniper all copies of the Software and related
documentation in Customer’s possession or control.

10. Taxes. All license fees payable under this agreement are exclusive of tax. Customer shall be responsible for paying Taxes arising from
the purchase of the license, or importation or use of the Software. If applicable, valid exemption documentation for each taxing jurisdiction
shall be provided to Juniper prior to invoicing, and Customer shall promptly notify Juniper if their exemption is revoked or modified. All
payments made by Customer shall be net of any applicable withholding tax. Customer will provide reasonable assistance to Juniper in
connection with such withholding taxes by promptly: providing Juniper with valid tax receipts and other required documentation showing
Customer’s payment of any withholding taxes; completing appropriate applications that would reduce the amount of withholding tax to
be paid; and notifying and assisting Juniper in any audit or tax proceeding related to transactions hereunder. Customer shall comply with
all applicable tax laws and regulations, and Customer will promptly pay or reimburse Juniper for all costs and damages related to any
liability incurred by Juniper as a result of Customer’s non-compliance or delay with its responsibilities herein. Customer’s obligations under
this Section shall survive termination or expiration of this Agreement.

11. Export. Customer agrees to comply with all applicable export laws and restrictions and regulations of any United States and any
applicable foreign agency or authority, and not to export or re-export the Software or any direct product thereof in violation of any such
restrictions, laws or regulations, or without all necessary approvals. Customer shall be liable for any such violations. The version of the
Software supplied to Customer may contain encryption or other capabilities restricting Customer’s ability to export the Software without
an export license.

iv Copyright © 2010, Juniper Networks, Inc.

12. Commercial Computer Software. The Software is “commercial computer software” and is provided with restricted rights. Use,
duplication, or disclosure by the United States government is subject to restrictions set forth in this Agreement and as provided in DFARS
227.7201 through 227.7202-4, FAR 12.212, FAR 27.405(b)(2), FAR 52.227-19, or FAR 52.227-14(ALT III) as applicable.

13. Interface Information. To the extent required by applicable law, and at Customer's written request, Juniper shall provide Customer
with the interface information needed to achieve interoperability between the Software and another independently created program, on
payment of applicable fee, if any. Customer shall observe strict obligations of confidentiality with respect to such information and shall use
such information in compliance with any applicable terms and conditions upon which Juniper makes such information available.

14. Third Party Software. Any licensor of Juniper whose software is embedded in the Software and any supplier of Juniper whose products
or technology are embedded in (or services are accessed by) the Software shall be a third party beneficiary with respect to this Agreement,
and such licensor or vendor shall have the right to enforce this Agreement in its own name as if it were Juniper. In addition, certain third party
software may be provided with the Software and is subject to the accompanying license(s), if any, of its respective owner(s). To the extent
portions of the Software are distributed under and subject to open source licenses obligating Juniper to make the source code for such
portions publicly available (such as the GNU General Public License (“GPL”) or the GNU Library General Public License (“LGPL”)), Juniper
will make such source code portions (including Juniper modifications, as appropriate) available upon request for a period of up to three
years from the date of distribution. Such request can be made in writing to Juniper Networks, Inc., 1194 N. Mathilda Ave., Sunnyvale, CA
94089, ATTN: General Counsel. You may obtain a copy of the GPL at http://www.gnu.org/licenses/gpl.html, and a copy of the LGPL
at http://www.gnu.org/licenses/lgpl.html .

15. Miscellaneous. This Agreement shall be governed by the laws of the State of California without reference to its conflicts of laws
principles. The provisions of the U.N. Convention for the International Sale of Goods shall not apply to this Agreement. For any disputes
arising under this Agreement, the Parties hereby consent to the personal and exclusive jurisdiction of, and venue in, the state and federal
courts within Santa Clara County, California. This Agreement constitutes the entire and sole agreement between Juniper and the Customer
with respect to the Software, and supersedes all prior and contemporaneous agreements relating to the Software, whether oral or written
(including any inconsistent terms contained in a purchase order), except that the terms of a separate written agreement executed by an
authorized Juniper representative and Customer shall govern to the extent such terms are inconsistent or conflict with terms contained
herein. No modification to this Agreement nor any waiver of any rights hereunder shall be effective unless expressly assented to in writing
by the party to be charged. If any portion of this Agreement is held invalid, the Parties agree that such invalidity shall not affect the validity
of the remainder of this Agreement. This Agreement and associated documentation has been written in the English language, and the
Parties agree that the English version will govern. (For Canada: Les parties aux présentés confirment leur volonté que cette convention de
même que tous les documents y compris tout avis qui s'y rattaché, soient redigés en langue anglaise. (Translation: The parties confirm that
this Agreement and all related documentation is and will be in the English language)).

Copyright © 2010, Juniper Networks, Inc. v

vi Copyright © 2010, Juniper Networks, Inc.
Table of Contents
About the Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii
JUNOS Documentation and Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii
Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii
Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii
Documentation Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii
Documentation Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xix
Requesting Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xx
Self-Help Online Tools and Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xx
Opening a Case with JTAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxi

Part 1 Overview of the MX80 3D Universal Edge Router

Chapter 1 Overview of the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
MX80 Router Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Chapter 2 MX80 Hardware Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
MX80 Chassis Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
MX80 Base Board Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Base Board Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
MX80 Cable Management Bracket Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
MX80 Cooling System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
MX80 Cooling System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
MX80 Front Panel Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
MX80 Front Panel Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Front Panel Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Alarm LEDs on the MX80 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Component LEDs on the MX80 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Link LEDs on the MX80 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Routing Engine LED on the MX80 Front Panel . . . . . . . . . . . . . . . . . . . . . 12
System LED on the MX80 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
MX80 Modular Interface Card Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
MX80 Modular Interface Card Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Built-in 10-Gigabit Ethernet MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Built-in Tri-Rate MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Front-Pluggable MICs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
MX80 Modular Interface Card LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
MX80 Power System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
MX80 Power System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
MX80 AC Power Supply Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
MX80 DC Power Supply Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MX80 Power Supply LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Copyright © 2010, Juniper Networks, Inc. vii

MX80 3D Universal Edge Router Hardware Guide

MX80 Routing Engine Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

MX80 Routing Engine Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
MX80 Routing Engine LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Part 2 Setting Up the MX80 Router

Chapter 3 Preparing the Site for MX80 Router Installation . . . . . . . . . . . . . . . . . . . . . . . 23
MX80 Site Preparation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
MX80 Router Rack Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
MX80 Router Clearance Requirements for Airflow and Hardware
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
MX80 Router Cabinet Requirements and Specifications . . . . . . . . . . . . . . . . . . . . 27
Chapter 4 Overview of MX80 Router Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
MX80 Installation Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Chapter 5 Unpacking the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Tools and Parts Required to Unpack the MX80 Router . . . . . . . . . . . . . . . . . . . . . . 31
Unpacking the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Verifying the MX80 Router Parts Received . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Chapter 6 Installing the MX80 Router Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . 35
Moving the Mounting Brackets for Center-Mounting the MX80 Router . . . . . . . . 35
Chapter 7 Installing the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Tools Required to Install the MX80 Chassis in the Rack . . . . . . . . . . . . . . . . . . . . . 37
Installing the MX80 Chassis in the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Installing the MX80 Cable Management Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Chapter 8 Connecting the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Tools and Parts Required for MX80 Router Connections . . . . . . . . . . . . . . . . . . . . 41
Connecting the MX80 Router to Management Devices . . . . . . . . . . . . . . . . . . . . . 41
Connecting the MX80 Router to a Network for Out-of-Band
Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Connecting the MX80 Router to a Management Console or Auxiliary
Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Connecting Interface Cables to the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . 43
Chapter 9 Grounding and Providing Power to the MX80 Router . . . . . . . . . . . . . . . . . . 45
Tools and Parts Required for MX80 Router Grounding and Power
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Grounding the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Connecting Power to an AC-Powered MX80 Router . . . . . . . . . . . . . . . . . . . . . . . 47
Powering On an AC-Powered MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Connecting Power to a DC-Powered MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . 49
Powering On a DC-Powered MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Chapter 10 Powering Off the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Powering Off the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Chapter 11 Configuring JUNOS Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Initially Configuring the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

viii Copyright © 2010, Juniper Networks, Inc.

 Table of Contents

Part 3 Hardware Maintenance, Troubleshooting, and Replacement

Procedures
Chapter 12 Maintaining MX80 Router Hardware Components . . . . . . . . . . . . . . . . . . . . . 61
Tools and Parts Required to Maintain the MX80 Router . . . . . . . . . . . . . . . . . . . . . 61
Routine Maintenance Procedures for the MX80 Router . . . . . . . . . . . . . . . . . . . . . 61
Maintaining the MX80 Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Maintaining the MX80 Fan Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Maintaining the MX80 MICs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Maintaining Cables That Connect to MX80 MICs . . . . . . . . . . . . . . . . . . . . . . . . . 64
Maintaining the MX80 Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Maintaining the MX80 Routing Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Chapter 13 Troubleshooting MX80 Hardware Components . . . . . . . . . . . . . . . . . . . . . . . 67
Troubleshooting Resources for MX80 Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Command-Line Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Chassis and Interface Alarm Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Component LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Troubleshooting the MX80 Fan Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Troubleshooting the MX80 MICs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Troubleshooting the MX80 Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Chapter 14 Replacing MX80 Hardware Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Replacing an MX80 Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Removing an MX80 Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Installing an MX80 Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Replacing an MX80 Fan Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Removing an MX80 Fan Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Installing an MX80 Fan Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Replacing an MX80 MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Removing an MX80 MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Installing an MX80 MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Installing an MX80 Dual-Wide MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Replacing a Cable on an MX80 MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Removing a Cable on an MX80 MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Installing a Cable on an MX80 MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Replacing an MX80 AC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Removing an MX80 AC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Installing an MX80 AC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Replacing an MX80 AC Power Supply Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Disconnecting an MX80 AC Power Supply Cord . . . . . . . . . . . . . . . . . . . . . . . 87
Connecting an MX80 AC Power Supply Cord . . . . . . . . . . . . . . . . . . . . . . . . . 88
Replacing an MX80 DC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Removing an MX80 DC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Installing an MX80 DC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Replacing an MX80 DC Power Supply Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Disconnecting an MX80 DC Power Supply Cable . . . . . . . . . . . . . . . . . . . . . . 92
Connecting an MX80 DC Power Supply Cable . . . . . . . . . . . . . . . . . . . . . . . . 93

Copyright © 2010, Juniper Networks, Inc. ix

MX80 3D Universal Edge Router Hardware Guide

Replacing an MX80 SFP or XFP Transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Removing an MX80 SFP or XFP Transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Installing an MX80 SFP or XFP Transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Part 4 Appendixes
Appendix A Safety and Regulatory Compliance Information for the MX80 Router . . . 99
Definition of Safety Warning Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Safety Guidelines and Warnings for the MX80 Router . . . . . . . . . . . . . . . . . . . . . 101
General Safety Guidelines for M Series, MX Series, and T Series Routers . . . 101
General Safety Warnings for M Series, MX Series, and T Series Routers . . . . 102
Qualified Personnel Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Restricted Access Area Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Preventing Electrostatic Discharge Damage to an MX80 Router . . . . . . . . . 104
Fire Safety Requirements for M Series, MX Series, and T Series Routers . . . 105
General Fire Safety Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Fire Suppression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Fire Suppression Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Installation Safety Warnings for M Series, MX Series, and T Series
Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Installation Instructions Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Rack-Mounting Requirements and Warnings . . . . . . . . . . . . . . . . . . . . . 107
Ramp Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
MX80 Chassis Lifting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
General Laser Safety Guidelines for M Series, MX Series, and T Series
Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Laser Safety Warnings for M Series, MX Series, and T Series Routers . . . . . . 112
Class 1 Laser Product Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Class 1 LED Product Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Laser Beam Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Radiation from Open Port Apertures Warning . . . . . . . . . . . . . . . . . . . . . 114
Maintenance and Operational Safety Warnings for M Series, MX Series, and
T Series Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Battery Handling Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Jewelry Removal Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Lightning Activity Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Operating Temperature Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Product Disposal Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
General Electrical Safety Guidelines and Warnings for the MX80 Router . . 120
General Electrical Safety Warnings for M Series, MX Series, and T Series
Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
General Electrical Safety Guidelines and Electrical Codes for M Series,
MX Series, and T Series Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
In Case of an Electrical Accident . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
AC Power Electrical Safety Guidelines and Warnings for MX80
Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
MX80 DC Power Electrical Safety Guidelines . . . . . . . . . . . . . . . . . . . . . 125

x Copyright © 2010, Juniper Networks, Inc.

 Table of Contents

DC Power Electrical Safety Warnings for M Series, MX Series, and T

Series Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Agency Approvals and Compliance Statements for the MX80 Router . . . . . . . . 129
Agency Approvals for MX80 Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Compliance Statements for NEBS for MX80 Routers . . . . . . . . . . . . . . . . . . 130
Compliance Statements for EMC Requirements for the MX80 Router . . . . . 131
Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
European Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
United States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Compliance Statements for Environmental Requirements for M Series, MX
Series, and T Series Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Compliance Statements for Acoustic Noise for MX80 Routers . . . . . . . . . . . 133
Appendix B MX80 Router Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
MX80 Router Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Appendix C MX80 Router Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 137
MX80 Router Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Appendix D Power Guidelines, Requirements, and Specifications for the MX80
Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
MX80 Router Grounding Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
MX80 Chassis Grounding Points Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 139
MX80 Router Grounding Cable Lug Specifications . . . . . . . . . . . . . . . . . . . . . . . . 140
MX80 Router Grounding Cable Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
MX80 Router AC Power Specifications and Requirements . . . . . . . . . . . . . . . . . . 141
MX80 Router AC Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Power Consumption for an AC-Powered MX80 Router . . . . . . . . . . . . . . . . . 142
AC Power Circuit Breaker Requirements for the MX80 Router . . . . . . . . . . . 143
AC Power Cord Specifications for the MX80 Router . . . . . . . . . . . . . . . . . . . 143
MX80 Router DC Power Specifications and Requirements . . . . . . . . . . . . . . . . . 145
MX80 Router DC Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Power Consumption for a DC-Powered MX80 Router . . . . . . . . . . . . . . . . . 146
DC Power Circuit Breaker Requirements for the MX80 Router . . . . . . . . . . . 148
DC Power Source Cabling for the MX80 Router . . . . . . . . . . . . . . . . . . . . . . 149
DC Power Cable Specifications for the MX80 Router . . . . . . . . . . . . . . . . . . 149
DC Power Cable Lug Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
DC Power Cable Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Site Electrical Wiring Guidelines for M Series, MX Series, and T Series
Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Distance Limitations for Signaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Radio Frequency Interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Electromagnetic Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151

Copyright © 2010, Juniper Networks, Inc. xi

MX80 3D Universal Edge Router Hardware Guide

Appendix E Cable and Wire Guidelines and Specifications for the MX80 Router . . . . . 153
Understanding Fiber-Optic Cable Signal Loss, Attenuation, and Dispersion . . . . 153
Signal Loss in Multimode and Single-Mode Fiber-Optic Cable . . . . . . . . . . . 153
Attenuation and Dispersion in Fiber-Optic Cable . . . . . . . . . . . . . . . . . . . . . . 153
Calculating Power Budget and Power Margin for Fiber-Optic Cables . . . . . . . . . 154
Calculating Power Budget for Fiber-Optic Cable . . . . . . . . . . . . . . . . . . . . . . 154
Calculating Power Margin for Fiber-Optic Cable . . . . . . . . . . . . . . . . . . . . . . 155
Routing Engine Interface Cable Specifications for MX80 Routers . . . . . . . . . . . . 156
Appendix F MX80 Cable Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
RJ-45 Connector Pinouts for the ETHERNET Port on the MX80 Router . . . . . . . 157
RJ-45 Connector Pinouts for the AUX and CONSOLE Ports on the MX80
Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Appendix G Contacting Customer Support and Returning MX80 Hardware . . . . . . . . . 159
Locating MX80 Component Serial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Displaying MX80 Components and Serial Numbers . . . . . . . . . . . . . . . . . . . 159
MX80 Chassis Serial Number Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
MX80 Fan Tray Serial Number Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
MX80 MIC Serial Number Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
MX80 Power Supply Serial Number Label . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Contacting Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Returning a Hardware Component to Juniper Networks, Inc. . . . . . . . . . . . . . . . . 164
Packing the MX80 Router for Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Guidelines for Packing Router Components for Shipment . . . . . . . . . . . . . . . . . . 166

Part 5 Index
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169

xii Copyright © 2010, Juniper Networks, Inc.

List of Figures
Part 1 Overview of the MX80 3D Universal Edge Router
Chapter 2 MX80 Hardware Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Figure 1: Front View of the MX80 Router (Fixed Chassis) . . . . . . . . . . . . . . . . . . . . . 5
Figure 2: Front View of the MX80 Router (Modular Chassis) . . . . . . . . . . . . . . . . . . 6
Figure 3: Rear View of the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 4: Cable Management Bracket for the MX80 Router . . . . . . . . . . . . . . . . . . 8
Figure 5: Airflow Through the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 6: Fan Tray and Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 7: Front Panel on the Fixed MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 8: Front Panel on the Modular MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 9: USB Memory Device in an MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 10: MICs Installed in an MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 11: AC Power Supplies Installed in an MX80 Router . . . . . . . . . . . . . . . . . . . 16
Figure 12: DC Power Supplies Installed in an MX80 Router . . . . . . . . . . . . . . . . . . . 17
Figure 13: AC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 14: DC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Part 2 Setting Up the MX80 Router

Chapter 3 Preparing the Site for MX80 Router Installation . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 15: Typical Open-Frame Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 16: MX80 Chassis Dimensions and Clearance Requirements . . . . . . . . . . . 27
Figure 17: Airflow Through Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Chapter 6 Installing the MX80 Router Mounting Hardware . . . . . . . . . . . . . . . . . . . . . . 35
Figure 18: Front-Mounting the Brackets on the MX80 Router . . . . . . . . . . . . . . . . 35
Figure 19: Center-Mounting the Brackets on the MX80 Router . . . . . . . . . . . . . . . 36
Chapter 7 Installing the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 20: Installing the Front-Mounted Router in the Rack . . . . . . . . . . . . . . . . . 39
Figure 21: Installing the Center-Mounted Router in the Rack . . . . . . . . . . . . . . . . . 39
Figure 22: Installing the Cable Management Bracket . . . . . . . . . . . . . . . . . . . . . . . 40
Chapter 8 Connecting the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 23: Routing Engine Ethernet Cable Connector . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 24: Ethernet Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 25: Routing Engine Console and Auxiliary Cable Connector . . . . . . . . . . . . 42
Figure 26: Auxiliary and Console Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 27: Attaching a Cable to a MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Chapter 9 Grounding and Providing Power to the MX80 Router . . . . . . . . . . . . . . . . . . 45
Figure 28: Grounding Points on the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . 46

Copyright © 2010, Juniper Networks, Inc. xiii

MX80 3D Universal Edge Router Hardware Guide

Figure 29: Connecting DC Power to the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Part 3 Hardware Maintenance, Troubleshooting, and Replacement

Procedures
Chapter 14 Replacing MX80 Hardware Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Figure 30: Removing the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Figure 31: Installing the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Figure 32: Removing the Fan Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Figure 33: Installing the Fan Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Figure 34: Removing a MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Figure 35: Removing a Dual-Wide MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Figure 36: Installing the Septum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Figure 37: Installing a MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Figure 38: Removing the Septum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Figure 39: Installing a Dual-Wide MIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Figure 40: Removing an AC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Figure 41: Installing an AC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Figure 42: Removing a DC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Figure 43: Disconnecting the DC Power Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Figure 44: Installing a DC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Figure 45: Connecting the DC Power Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Figure 46: Connecting Power Cables to the DC Power Supply . . . . . . . . . . . . . . . 94
Figure 47: Removing SFPs or XFPs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Part 4 Appendixes
Appendix A Safety and Regulatory Compliance Information for the MX80 Router . . . 99
Figure 48: ESD Points on the MX80 Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Figure 49: Placing a Component into an Electrostatic Bag . . . . . . . . . . . . . . . . . . 105
Figure 50: MX80 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Appendix D Power Guidelines, Requirements, and Specifications for the MX80
Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Figure 51: Grounding Points on the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . 140
Figure 52: Grounding Cable Lug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Figure 53: AC Plug Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Figure 54: DC Power Cable Lug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Appendix G Contacting Customer Support and Returning MX80 Hardware . . . . . . . . . 159
Figure 55: Serial Number ID Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Figure 56: MX80 Chassis Serial Number Label . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Figure 57: MX80 Fan Tray Serial Number Label . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Figure 58: 20-Port MIC Serial Number Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Figure 59: 40-Port MIC Serial Number Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Figure 60: 2-Port MIC Serial Number Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Figure 61: Power Supply Serial Number Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163

xiv Copyright © 2010, Juniper Networks, Inc.

List of Tables
About the Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii
Table 1: Notice Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii
Table 2: Text and Syntax Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii

Part 1 Overview of the MX80 3D Universal Edge Router

Chapter 2 MX80 Hardware Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Table 3: Alarm LEDs on the MX80 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Table 4: Link LEDs on the MX80 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 5: Routing Engine LED on the MX80 Front Panel . . . . . . . . . . . . . . . . . . . . . . 12
Table 6: System LED on the MX80 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 7: Tri-Rate MIC LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 8: Power Supply LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Part 2 Setting Up the MX80 Router

Chapter 3 Preparing the Site for MX80 Router Installation . . . . . . . . . . . . . . . . . . . . . . . 23
Table 9: MX80 Site Preparation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 10: MX80 Rack Requirements and Specifications . . . . . . . . . . . . . . . . . . . . 24
Table 11: Cabinet Requirements and Specifications for an MX80 Router . . . . . . . . 27
Chapter 5 Unpacking the MX80 Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 12: Parts List for a Fully Configured Router . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Table 13: Accessory Box Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Part 4 Appendixes
Appendix B MX80 Router Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Table 14: MX80 Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Appendix C MX80 Router Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 137
Table 15: Router Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Appendix D Power Guidelines, Requirements, and Specifications for the MX80
Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Table 16: AC Power System Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . 141
Table 17: AC Power Supply Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . 141
Table 18: AC Base Router Power Requirements for the Fixed MX80 Router . . . . 142
Table 19: AC Base Router Power Requirements for the Modular MX80
Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Table 20: Component Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Table 21: AC Power Cord Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

Copyright © 2010, Juniper Networks, Inc. xv

MX80 3D Universal Edge Router Hardware Guide

Table 22: DC Power System Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . 146

Table 23: DC Power Supply Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . 146
Table 24: DC-Powered Base Router Power Requirements for the Fixed MX80
Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Table 25: DC-Powered Base Router Power Requirements for the Modular MX80
Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Table 26: Component Power Requirements for DC-Powered Routers . . . . . . . . . 147
Appendix E Cable and Wire Guidelines and Specifications for the MX80 Router . . . . . 153
Table 27: Estimated Values for Factors Causing Link Loss . . . . . . . . . . . . . . . . . . 155
Table 28: Cable Specifications for Routing Engine Management . . . . . . . . . . . . . 156
Appendix F MX80 Cable Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Table 29: RJ-45 Connector Pinout for the Routing Engine ETHERNET Port . . . . . 157
Table 30: RJ-45 Connector Pinout for the AUX and CONSOLE Ports . . . . . . . . . 158

xvi Copyright © 2010, Juniper Networks, Inc.

About the Documentation

• JUNOS Documentation and Release Notes on page xvii

• Objectives on page xvii
• Audience on page xviii
• Documentation Conventions on page xviii
• Documentation Feedback on page xix
• Requesting Technical Support on page xx

JUNOS Documentation and Release Notes

For a list of related JUNOS documentation, see

http://www.juniper.net/techpubs/software/junos/ .

If the information in the latest release notes differs from the information in the
documentation, follow the JUNOS Release Notes.
®
To obtain the most current version of all Juniper Networks technical documentation,
see the product documentation page on the Juniper Networks website at
http://www.juniper.net/techpubs/.

Objectives

This documentation describes hardware components, installation, basic configuration,

and basic troubleshooting procedures for the Juniper Networks MX80 3D Universal Edge
Router. It explains how to prepare your site for router installation, unpack and install the
hardware, power on the router, perform initial software configuration, and perform routine
maintenance. After completing the installation and basic configuration procedures
covered in this documentation, see the JUNOS Software configuration guides for
information about further JUNOS Software configuration.

NOTE: For additional information about Juniper Networks 3D Universal Edge routers
and the line cards they support—either corrections to or information that might have
been omitted from this guide—see the hardware release notes at http://www.juniper.net/.

Copyright © 2010, Juniper Networks, Inc. xvii

MX80 3D Universal Edge Router Hardware Guide

Audience

This documentation is designed for network administrators who are installing and
maintaining a Juniper Networks router or preparing a site for router installation. To use
the documentation, you need a broad understanding of networks in general, the Internet
in particular, networking principles, and network configuration. Any detailed discussion
of these concepts is beyond the scope of this hardware documentation.

Documentation Conventions

Table 1 on page xviii defines the notice icons used in this guide.

Table 1: Notice Icons

Icon Meaning Description

Informational note Indicates important features or instructions.

Caution Indicates a situation that might result in loss of data or hardware damage.

Warning Alerts you to the risk of personal injury or death.

Laser warning Alerts you to the risk of personal injury from a laser.

Table 2 on page xviii defines the text and syntax conventions used in this guide.

Table 2: Text and Syntax Conventions

Convention Description Examples

Bold text like this Represents text that you type. To enter configuration mode, type the
configure command:

user@host> configure

Fixed-width text like this Represents output that appears on the user@host> show chassis alarms
terminal screen. No alarms currently active

Italic text like this • Introduces important new terms. • A policy term is a named structure
• Identifies book names. that defines match conditions and
actions.
• Identifies RFC and Internet draft titles.
• JUNOS System Basics Configuration
Guide
• RFC 1997, BGP Communities Attribute

xviii Copyright © 2010, Juniper Networks, Inc.

 About the Documentation

Table 2: Text and Syntax Conventions (continued)

Convention Description Examples

Italic text like this Represents variables (options for which Configure the machine’s domain name:
you substitute a value) in commands or
configuration statements. [edit]
root@# set system domain-name
domain-name

Plain text like this Represents names of configuration • To configure a stub area, include the
statements, commands, files, and stub statement at the [edit protocols
directories; IP addresses; configuration ospf area area-id] hierarchy level.
hierarchy levels; or labels on routing • The console port is labeled CONSOLE.
platform components.

< > (angle brackets) Enclose optional keywords or variables. stub <default-metric metric>;

| (pipe symbol) Indicates a choice between the mutually broadcast | multicast

exclusive keywords or variables on either
side of the symbol. The set of choices is (string1 | string2 | string3)
often enclosed in parentheses for clarity.

# (pound sign) Indicates a comment specified on the rsvp { # Required for dynamic MPLS only
same line as the configuration statement
to which it applies.

[ ] (square brackets) Enclose a variable for which you can community name members [
substitute one or more values. community-ids ]

Indention and braces ( { } ) Identify a level in the configuration [edit]

hierarchy. routing-options {
static {
route default {
; (semicolon) Identifies a leaf statement at a
nexthop address;
configuration hierarchy level.
retain;
}
}
}

J-Web GUI Conventions

Bold text like this Represents J-Web graphical user • In the Logical Interfaces box, select
interface (GUI) items you click or select. All Interfaces.
• To cancel the configuration, click
Cancel.

> (bold right angle bracket) Separates levels in a hierarchy of J-Web In the configuration editor hierarchy,
selections. select Protocols>Ospf.

Documentation Feedback

We encourage you to provide feedback, comments, and suggestions so that we can

improve the documentation. You can send your comments to
[email protected], or fill out the documentation feedback form at

Copyright © 2010, Juniper Networks, Inc. xix

MX80 3D Universal Edge Router Hardware Guide

https://www.juniper.net/cgi-bin/docbugreport/. If you are using e-mail, be sure to include

the following information with your comments:

• Document or topic name

• URL or page number

• Software release version (if applicable)

Requesting Technical Support

Technical product support is available through the Juniper Networks Technical Assistance
Center (JTAC). If you are a customer with an active J-Care or JNASC support contract,
or are covered under warranty, and need post-sales technical support, you can access
our tools and resources online or open a case with JTAC.

• JTAC policies—For a complete understanding of our JTAC procedures and policies,

review the JTAC User Guide located at
http://www.juniper.net/us/en/local/pdf/resource-guides/7100059-en.pdf .

• Product warranties—For product warranty information, visit

http://www.juniper.net/support/warranty/ .

• JTAC hours of operation—The JTAC centers have resources available 24 hours a day,
7 days a week, 365 days a year.

Self-Help Online Tools and Resources

For quick and easy problem resolution, Juniper Networks has designed an online
self-service portal called the Customer Support Center (CSC) that provides you with the
following features:

• Find CSC offerings: http://www.juniper.net/customers/support/

• Search for known bugs: http://www2.juniper.net/kb/

• Find product documentation: http://www.juniper.net/techpubs/

• Find solutions and answer questions using our Knowledge Base: http://kb.juniper.net/

• Download the latest versions of software and review release notes:

http://www.juniper.net/customers/csc/software/

• Search technical bulletins for relevant hardware and software notifications:

https://www.juniper.net/alerts/

• Join and participate in the Juniper Networks Community Forum:

http://www.juniper.net/company/communities/

• Open a case online in the CSC Case Management tool: http://www.juniper.net/cm/

To verify service entitlement by product serial number, use our Serial Number Entitlement
(SNE) Tool: https://tools.juniper.net/SerialNumberEntitlementSearch/

xx Copyright © 2010, Juniper Networks, Inc.

 About the Documentation

Opening a Case with JTAC

You can open a case with JTAC on the Web or by telephone.

• Use the Case Management tool in the CSC at http://www.juniper.net/cm/ .

• Call 1-888-314-JTAC (1-888-314-5822 toll-free in the USA, Canada, and Mexico).

For international or direct-dial options in countries without toll-free numbers, see

http://www.juniper.net/support/requesting-support.html .

Copyright © 2010, Juniper Networks, Inc. xxi

MX80 3D Universal Edge Router Hardware Guide

xxii Copyright © 2010, Juniper Networks, Inc.

PART 1

Overview of the MX80 3D Universal Edge

Router
• Overview of the MX80 Router on page 3
• MX80 Hardware Components on page 5

Copyright © 2010, Juniper Networks, Inc. 1

MX80 3D Universal Edge Router Hardware Guide

2 Copyright © 2010, Juniper Networks, Inc.

CHAPTER 1

Overview of the MX80 Router

• MX80 Router Overview on page 3

MX80 Router Overview

The MX80 3D Universal Edge Router is an Ethernet-optimized edge router that provides
both switching and carrier-class Ethernet routing. The MX80 router enables a wide range
of business and residential applications and services, including high-speed transport and
virtual private network (VPN) services, next-generation broadband multiplay services,
and high-volume Internet data center internetworking. The MX80 router has high-density
Ethernet interfaces and high-capacity switching throughput.

The MX80 router is a single-board router with a built-in Routing Engine and one Packet
Forwarding Engine. The Packet Forwarding Engine has two “pseudo” Flexible PIC
Concentrators (FPC 0 and FPC1). Because there is no switching fabric, the single Packet
Forwarding Engine takes care of both ingress and egress packet forwarding.

The MX80 router is a compact router that is two rack units (U) tall. Several routers can
be stacked in a single floor-to-ceiling rack for increased port density per unit of floor
space.

The MX80 router is available as a modular (MX80) or fixed (MX80-48T) chassis. Both
chassis have a fixed Modular Interface Card (MIC) that has 4 10-Gigabit Ethernet ports.
The fixed MX80 router has an additional 48 10/100/1000Base-T RJ45 ports. The modular
chassis has two dedicated slots for MICs. (The Services PIC slot located in the rear of
the chassis is currently not supported.) For a list of the supported MICs, see MICs
Supported by MX Series Routers in the MX Series 3D Universal Edge Routers Line Card
Guide.

Related Topics • MX80 Chassis Description on page 5

• MX80 Cooling System Description on page 8

• MX80 Front Panel Description on page 9

• MX80 Modular Interface Card Description on page 13

• MX80 Power System Description on page 16

• MX80 Router Physical Specifications on page 135

Copyright © 2010, Juniper Networks, Inc. 3

MX80 3D Universal Edge Router Hardware Guide

4 Copyright © 2010, Juniper Networks, Inc.

CHAPTER 2

MX80 Hardware Components

• MX80 Chassis Description on page 5

• MX80 Base Board Description on page 6
• MX80 Cable Management Bracket Description on page 7
• MX80 Cooling System Overview on page 8
• MX80 Front Panel Overview on page 9
• MX80 Modular Interface Card Overview on page 13
• MX80 Power System Overview on page 16
• MX80 Routing Engine Overview on page 19

MX80 Chassis Description

The router chassis is a rigid sheet metal structure that houses all the other router
components (see Figure 1 on page 5, Figure 2 on page 6, and Figure 3 on page 6). The
chassis measures 3.5 in. (8.9 cm) high, 19.2 in. (48.7 cm) wide, and 21.75 in. (55.2 cm)
deep (from the front-mounting brackets to the rear of the chassis). The chassis installs
in standard 600-mm deep (or larger) enclosed cabinets, 19-in. equipment racks, or telco
open-frame racks.

Figure 1: Front View of the MX80 Router (Fixed Chassis)

Network ports
g005001

AC power supplies Front panel Fan tray (and air filter)

Copyright © 2010, Juniper Networks, Inc. 5

MX80 3D Universal Edge Router Hardware Guide

Figure 2: Front View of the MX80 Router (Modular Chassis)

ESD MIC slots
point

g005000
AC power supplies Front panel Fan tray (and air filter)

Figure 3: Rear View of the MX80 Router

MIC Protective ESD
slot earthing terminal point

CLOCK

g005002
SYNC

Clock Sync
port port

Related Topics • MX80 Router Overview on page 3

• MX80 Router Physical Specifications on page 135

MX80 Base Board Description

The base board is located in the center of the chassis and forms the rear of the MIC card
cage. The base board is not replaceable. The MICs and power supplies install into the
base board from the front of the chassis. Data packets are transferred across the base
board from the MIC to the Packet Forwarding Engine, and from the Packet Forwarding
Engine across the base board to the destination MIC.

The base board provides the following functions:

• Powers on and powers off MICs

• Controls clocking, system resets, and booting

6 Copyright © 2010, Juniper Networks, Inc.

 Chapter 2: MX80 Hardware Components

• Monitors and controls system functions, including fan speed, board power status, PDM
status and control, and the front panel

• Provides interconnections to all the MICs within the chassis

Base Board Components

The base board consists of the following components:

• JUNOS Trio chipset—Manages packet data memory, queuing systems, and performs
packet lookup and encapsulation.

• MIC connectors for both built-in and replaceable MICs including a WAN interface for
the built-in 10-Gigabit Ethernet MIC.

• Intake and exhaust temperature sensors.

• Circuits for chassis management and control.

• Power circuits for the system components and Ethernet interfaces.

• Routing Engine processor, which includes a 1.33-GHz CPU, and 2 GB of SDRAM.

• 2 4-GB NAND flash storage devices.

• Packet Forwarding Engine processor, which includes a 1-GHz CPU, a system controller,
and 1 GB of SDRAM. Connects to the Routing Engine through a Gigabit Ethernet link.

• Clock logic.

Related Topics • MX80 Router Overview on page 3

• MX80 Chassis Description on page 5

• MX80 Routing Engine Description on page 19

MX80 Cable Management Bracket Description

The cable management bracket (see Figure 4 on page 8) consists of plastic dividers
and installs on the left side of the chassis. The cable management bracket allows you
to route the cables outside the router and away from the MICs.

Copyright © 2010, Juniper Networks, Inc. 7

MX80 3D Universal Edge Router Hardware Guide

Figure 4: Cable Management Bracket for the MX80 Router

Cable
management
bracket

g005035
Related Topics • Installing the MX80 Cable Management Bracket on page 39

• Connecting the MX80 Router to Management Devices on page 41

• Connecting Interface Cables to the MX80 Router on page 43

• Maintaining Cables That Connect to MX80 MICs on page 64

MX80 Cooling System Overview

• MX80 Cooling System Description on page 8

MX80 Cooling System Description

The cooling system consists of the following components:

• Fan tray

• Air filter

The cooling system components work together to keep all router components within the
acceptable temperature range (see Figure 5 on page 9 and Figure 6 on page 9). The
router has one fan tray and one air filter that install vertically in the front of the router.
The fan tray contains five fans.

The air intake to cool the chassis is located on the right side of the chassis next to the air
filter. Air is pulled through the air filter toward the fan tray, where it is exhausted out the
left side of the system. The power supplies are self cooling and are located in the front
of the router to the left of the front panel. The exhaust for the power supplies is located
on the left side of the chassis.

8 Copyright © 2010, Juniper Networks, Inc.

 Chapter 2: MX80 Hardware Components

Figure 5: Airflow Through the MX80 Router

Front view
airflow

g005016
Power supply exhaust Fan tray/
air filter

The chassis monitors the temperature of the router components. When the router is
operating normally, the fans function at lower than full speed. If a fan fails or the ambient
temperature rises above a threshold, the speed of the remaining fans is automatically
adjusted to keep the temperature within the acceptable range. If the ambient maximum
temperature specification is exceeded and the system cannot be adequately cooled, the
Routing Engine shuts down the system by disabling output power from each power
supply.

Figure 6: Fan Tray and Air Filter

Fan tray

g005026

Air filter

Thumbscrew Handle

Related Topics • Maintaining the MX80 Air Filter on page 62

• Maintaining the MX80 Fan Tray on page 62

• Troubleshooting the MX80 Fan Tray on page 69

• Replacing an MX80 Fan Tray on page 75

MX80 Front Panel Overview

• MX80 Front Panel Description on page 9

• Alarm LEDs on the MX80 Front Panel on page 11
• Component LEDs on the MX80 Front Panel on page 11

MX80 Front Panel Description

The front panel is located on the front of the MX80 router and allows you to view status
and troubleshooting information at a glance. The front panel contains LEDs for the router

Copyright © 2010, Juniper Networks, Inc. 9

MX80 3D Universal Edge Router Hardware Guide

components, online/offline and reset buttons, auxiliary and console ports, clocking ports,
and ports for the 10-Gigabit Ethernet MIC.

Figure 7: Front Panel on the Fixed MX80 Router

Alarm Routing Console Ethernet
LEDs Engine port port
LED

MX80-48T

System
status
LED ONLINE/
OFFLINE

g005047
ONLINE/ Reset Auxiliary USB
OFFLINE button port port 10-Gigabit Ethernet MIC
button

Figure 8: Front Panel on the Modular MX80 Router

Alarm Routing Console Ethernet
LEDs Engine port port
LED

MX80

System
status
LED ONLINE/
OFFLINE

g005046
ONLINE/ Reset Auxiliary USB Clock
OFFLINE button port port ports 10-Gigabit Ethernet MIC
button

Front Panel Components

Each front panel consists of the following components:

• Interface ports—The AUX, CONSOLE, and ETHERNET provide access to management

devices. Each Routing Engine has one 1-Gbps Ethernet port for connecting to a
management network and two asynchronous serial ports—one for connecting to a
console and one for connecting to a modem or other auxiliary device.

• Two ports for primary and secondary BITS clock input are available on the modular
MX80 chassis.

• One fixed 10-Gigabit Ethernet MIC with four ports for uplink connections. For more
information see “MX80 Modular Interface Card Description” on page 13.

• USB port—Provides a removable media interface through which you can install the
JUNOS Software manually. (See Figure 9 on page 11.) JUNOS Software supports USB
version 1.0.

• Router online/offline button—Takes the router online or offline when pressed.

• Reset button—Reboots the Routing Engine when pressed.

• LEDs—Indicate component and system status and troubleshooting information at a

glance.

10 Copyright © 2010, Juniper Networks, Inc.

 Chapter 2: MX80 Hardware Components

Figure 9: USB Memory Device in an MX80 Router

USB Memory card

g005008
Related Topics • Alarm LEDs on the MX80 Front Panel on page 11

• Component LEDs on the MX80 Front Panel on page 11

Alarm LEDs on the MX80 Front Panel

Two alarm LEDs are located at the left of the front panel. The circular red LED lights to
indicate a critical condition that can result in a system shutdown. The triangular yellow
LED lights to indicate a less severe condition that requires monitoring or maintenance.
Both LEDs can be lit simultaneously.

Table 3 on page 11 describes the alarm LEDs in more detail.

Table 3: Alarm LEDs on the MX80 Front Panel

Shape Color State Description

Red On steadily Critical alarm LED—Indicates a critical condition that

can cause the router to stop functioning. Possible
causes include component removal, failure, or
overheating.

Yellow On steadily Warning alarm LED—Indicates a serious but nonfatal

error condition, such as a maintenance alert or a
significant increase in component temperature.

Component LEDs on the MX80 Front Panel

• Link LEDs on the MX80 Front Panel on page 12
• Routing Engine LED on the MX80 Front Panel on page 12
• System LED on the MX80 Front Panel on page 12

Copyright © 2010, Juniper Networks, Inc. 11

MX80 3D Universal Edge Router Hardware Guide

Link LEDs on the MX80 Front Panel

The front panel has a 10-Gigabit Ethernet MIC with four ports for uplink connections.
Each port has one LINK LED located to the right of the port. Table 4 on page 12 describes
the link LEDs in more detail.

Table 4: Link LEDs on the MX80 Front Panel

Label Color State Description

LINK Green Blinking Link is up and is active.

On steadily Link is up with no activity.

Off No link.

Routing Engine LED on the MX80 Front Panel

One LED on the left side of the front panel indicates the status of the Routing Engine.
The LED is located below the RE label. Table 5 on page 12 describes the Routing Engine
LED in more detail.

Table 5: Routing Engine LED on the MX80 Front Panel

Label Color State Description

RE Green Blinking Routing Engine is transitioning online.

On steadily Routing Engine is functioning normally.

Red On steadily Routing Engine has failed.

System LED on the MX80 Front Panel

One LED on the left side of the front panel indicates the status of the MX80 router. The
LED is located below the SYS OK label. Table 6 on page 12 describes the system LED in
more detail.

Table 6: System LED on the MX80 Front Panel

Label Color State Description

SYS OK Green Blinking Router is transitioning online.

On steadily Router is functioning normally.

Related Topics • Alarm LEDs on the MX80 Front Panel on page 11

• Troubleshooting Resources for MX80 Routers on page 67

• Troubleshooting the MX80 Fan Tray on page 69

12 Copyright © 2010, Juniper Networks, Inc.

 Chapter 2: MX80 Hardware Components

• Troubleshooting the MX80 MICs on page 70

• Troubleshooting the MX80 Power Supplies on page 70

MX80 Modular Interface Card Overview

• MX80 Modular Interface Card Description on page 13

• MX80 Modular Interface Card LEDs on page 15

MX80 Modular Interface Card Description

Modular Interface Cards (MICs) provide the physical connections to various network
media types. MICs receive incoming packets from the network and transmit outgoing
packets to the network. During this process, each MIC performs framing and high-speed
signaling for its media type. Before transmitting outgoing data packets through the MIC
interfaces, the router encapsulates the packets received.

On the fixed MX80 chassis, the MICs come preinstalled and cannot be replaced.

On the modular MX80 chassis, MICs install into two slots in the front of the router.

The Services PIC slot located in the rear of the chassis is currently not supported.

Figure 10: MICs Installed in an MX80 Router

MIC slots

g005025

The MX80 router supports the following types of MICs:

• Built-in 10-Gigabit Ethernet MIC on page 13

• Built-in Tri-Rate MIC on page 14
• Front-Pluggable MICs on page 15

Built-in 10-Gigabit Ethernet MIC

The built-in 10-Gigabit Ethernet MIC is fixed on both models of the MX80 router. The
fixed MIC is labeled 0/MIC 0 and is located on the front panel. The built-in 10-Gigabit
Ethernet MIC has the following components:

• Four 10-Gigabit Ethernet ports labeled 0 through 3, left to right.

• High-performance throughput on each port at speeds up to 10 Gbps

Copyright © 2010, Juniper Networks, Inc. 13

MX80 3D Universal Edge Router Hardware Guide

• Up to 30-Gbps of full-duplex traffic

• LAN-PHY mode at 10.3125 Gbps

• WAN-PHY mode at 9.953 Gbps

• Maximum transmission units (MTUs) of up to 9192 bytes

• Configurable LAN-PHY and WAN-PHY mode options

• Synchronous Ethernet support

• Optical diagnostics and related alarms

• Cables and connectors:

• Duplex LC/PC connector (Rx and Tx)

• Fiber-optic 10-gigabit small form-factor pluggable (XFP) transceivers:

• 10GBASE-E (model number: XFP-10G-E-OC192-IR2)

• 10GBASE-L (model number: XFP-10G-L-OC192-SR1)

• 10GBASE-S (model number: XFP-10G-S)

• 10GBASE-Z (model number: XFP-10G-Z-OC192-LR2)

Optical interface specifications—see 10-Gigabit Ethernet Transceiver Optical Interface

Specifications

• Link LED, one green per port. For more information, see “Link LEDs on the MX80 Front
Panel” on page 12.

Built-in Tri-Rate MIC

The built-in Tri-Rate MIC is only available on the fixed MX80 chassis and is not
replaceable. The built-in Tri-Rate MIC has the following components:

• 48 autonegotiating 10Base-T, 100Base-TX, or 1000Base-T Megabit Ethernet ports.

• Autonegotiation between Gigabit Ethernet circuit partners.

• Up to 40-Gbps of full-duplex traffic.

• Maximum transmission units (MTUs) of up to 9192 bytes.

• Connector: Four-pair, Category 5 shielded twisted-pair connectivity through an RJ-45

connector.

• Pinout: MDI/MDI-X.

• Maximum distance: 328 ft (100 m).

• Link LED, one green per port. For more information, see Table 7 on page 15.

14 Copyright © 2010, Juniper Networks, Inc.

 Chapter 2: MX80 Hardware Components

Front-Pluggable MICs
You can only install and remove MICs in the modular MX80 chassis. The MIC slots are
labeled 1/MIC 0 and 1/MIC 1. Each MIC slot in the modular MX80 chassis has an ejector
handle located above the MIC slot.

You can install MICs of different media types as long as the MX80 router supports those
MICs.

For more information about supported MICs, see MICs Supported by MX Series Routers.

Related Topics • MX80 Modular Interface Card LEDs on page 15

• Maintaining the MX80 MICs on page 63

• Troubleshooting the MX80 MICs on page 70

• Replacing an MX80 MIC on page 76

MX80 Modular Interface Card LEDs

The fixed 10-Gigabit Ethernet Modular Interface Card (MIC) has link LEDs located on the
front panel. For more information about the link LEDs for the 10-Gigabit Ethernet MIC,
see “Link LEDs on the MX80 Front Panel” on page 12.

Each hot-removable and hot-insertable MIC has LEDs located on the faceplate. For more
information about LEDs on the MIC faceplate, see the “LEDs” section for each MIC in the
MX Series 3D Universal Edge Routers Line Card Guide.

On the fixed MX80 chassis, each of the 48 ports on the fixed Tri-Rate MIC has a link LED.
Table 7 on page 15 describes the link LEDs in more detail.

Table 7: Tri-Rate MIC LEDs

Color State Description

Green On steadily Link is up with no activity.

Blinking Link is up and is active.

Off No link.

Related Topics • MICs Supported by MX Series Routers

• MX80 Modular Interface Card Description on page 13

• Maintaining the MX80 MICs on page 63

• Troubleshooting the MX80 MICs on page 70

• Replacing an MX80 MIC on page 76

Copyright © 2010, Juniper Networks, Inc. 15

MX80 3D Universal Edge Router Hardware Guide

MX80 Power System Overview

• MX80 Power System Description on page 16

• MX80 Power Supply LED on page 18

MX80 Power System Description

The MX80 router uses either AC or DC power supplies (see Figure 11 on page 16 and Figure
12 on page 17). The router contains either one or two power supplies located at the front
of the chassis in slots PS0 and PS1 (right to left). Each power supply has a handle, an
ejection lever, a power switch, and a status LED. The power supplies connect to the base
board, which distributes the different output voltages produced by the power supplies
to the router components, depending on their voltage requirements. When two power
supplies are present, they share power almost equally within a fully populated system.
If one power supply in a redundant configuration fails or is removed, the remaining power
supply assumes the entire electrical load without interruption. A single power supply
provides the maximum configuration with full power for as long as the router is operational.
A second power supply can be installed for redundancy. Each power supply is cooled by
its own internal cooling system.

Redundant power supplies are hot-removable and hot-insertable. When you remove a
power supply from a router that uses only one power supply, the router might shut down
depending on your configuration.

CAUTION: The router cannot be powered from AC and DC power supplies

simultaneously.

NOTE: Routers configured with only one power supply are shipped with a blank panel
installed over the power supply slot that is not populated.

Figure 11: AC Power Supplies Installed in an MX80 Router g005011

AC power supplies

16 Copyright © 2010, Juniper Networks, Inc.

 Chapter 2: MX80 Hardware Components

Figure 12: DC Power Supplies Installed in an MX80 Router

g005012
DC power supplies

• MX80 AC Power Supply Description on page 17

• MX80 DC Power Supply Description on page 18

MX80 AC Power Supply Description

Each AC power supply weighs approximately 2.6 lb (1.18 kg) and consists of a handle,
an ejection lever, an AC appliance inlet, an AC input switch, a fan, and an LED to monitor
the status of the power supply. Figure 13 on page 17 shows the power supply.

Each inlet requires a dedicated AC power feed and a dedicated customer site circuit
breaker. We recommend that you use a minimum 15 A (110 VAC) customer site circuit
breaker, or as required by local code.

Figure 13: AC Power Supply

g005022

Ejector lever Status LED

Handle AC power Power

inlet switch

WARNING: The router is pluggable type A equipment installed in a restricted-access

location. It has a separate protective earthing terminal (sized for SAE 10-32 ground
screws) provided on the chassis in addition to the grounding pin of the power supply
cord. This separate protective earthing terminal must be permanently connected to
earth.

Copyright © 2010, Juniper Networks, Inc. 17

MX80 3D Universal Edge Router Hardware Guide

MX80 DC Power Supply Description

Each DC power supply has a handle, an ejection lever, a power switch, a status LED, and
a terminal block that provides a single DC input (–48 VDC and return) that requires a
dedicated customer site circuit breaker. We recommend that you use a dedicated
customer site circuit breaker rated for 25 A (–48 VDC) minimum, or as required by local
code. Figure 14 on page 18 shows the power supply.

Figure 14: DC Power Supply

g005023
Ejector lever Status LED

Handle DC Power
terminal switch
block

Related Topics • MX80 Power Supply LED on page 18

• Maintaining the MX80 Power Supplies on page 65

• Troubleshooting the MX80 Power Supplies on page 70

• MX80 Router AC Power Specifications on page 141

• MX80 Router DC Power Specifications on page 146

MX80 Power Supply LED

Each power supply has a bi-color status LED located above the power switch on the
power supply.

Table 8: Power Supply LED

Color State Description

Green On steadily Power supply is functioning normally.

Red On steadily Power supply has failed.

Related Topics • MX80 Power System Description on page 16

• Maintaining the MX80 Power Supplies on page 65

• Troubleshooting the MX80 Power Supplies on page 70

• MX80 Router AC Power Specifications on page 141

18 Copyright © 2010, Juniper Networks, Inc.

 Chapter 2: MX80 Hardware Components

• MX80 Router DC Power Specifications on page 146

MX80 Routing Engine Overview

• MX80 Routing Engine Description on page 19

• MX80 Routing Engine LED on page 19

MX80 Routing Engine Description

The Routing Engine is built-in on the MX80 base board and cannot be replaced.

The Routing Engine consists of the following components:

• Processor—Runs JUNOS Software to maintain the router's routing tables and routing
protocols.

• DRAM—Buffers incoming packets and provides storage for the routing and forwarding
tables and for other Routing Engine processes. To view the amount of DRAM installed
on your router, issue the show chassis routing-engine command.

• NAND flash—Provides primary storage for software images, configuration files, and
microcode.

Related Topics • MX80 Routing Engine LED on page 19

• Maintaining the MX80 Routing Engine on page 66

• show chassis routing-engine

MX80 Routing Engine LED

The Routing Engine LED appears on the left of the front panel and is labeled RE. For more
information see “Routing Engine LED on the MX80 Front Panel” on page 12.

Related Topics • MX80 Routing Engine Description on page 19

• Maintaining the MX80 Routing Engine on page 66

Copyright © 2010, Juniper Networks, Inc. 19

MX80 3D Universal Edge Router Hardware Guide

20 Copyright © 2010, Juniper Networks, Inc.

PART 2

Setting Up the MX80 Router

• Preparing the Site for MX80 Router Installation on page 23
• Overview of MX80 Router Installation on page 29
• Unpacking the MX80 Router on page 31
• Installing the MX80 Router Mounting Hardware on page 35
• Installing the MX80 Router on page 37
• Connecting the MX80 Router on page 41
• Grounding and Providing Power to the MX80 Router on page 45
• Powering Off the MX80 Router on page 53
• Configuring JUNOS Software on page 55

Copyright © 2010, Juniper Networks, Inc. 21

MX80 3D Universal Edge Router Hardware Guide

22 Copyright © 2010, Juniper Networks, Inc.

CHAPTER 3

Preparing the Site for MX80 Router

Installation

• MX80 Site Preparation Checklist on page 23

• MX80 Router Rack Requirements on page 24
• MX80 Router Clearance Requirements for Airflow and Hardware
Maintenance on page 26
• MX80 Router Cabinet Requirements and Specifications on page 27

MX80 Site Preparation Checklist

The checklist in Table 9 on page 23 summarizes the tasks you must perform when
preparing a site for router installation.

Table 9: MX80 Site Preparation Checklist

Item or Task For More Information Performed By Date

Verify that environmental factors such as “MX80 Router Environmental

temperature and humidity do not exceed router Specifications” on page 137
tolerances.

Select the type of rack or cabinet. “MX80 Router Rack Requirements”

on page 24,
“MX80 Router Cabinet Requirements
and Specifications” on page 27

Plan rack or cabinet location, including required “MX80 Router Rack Requirements”
space clearances. on page 24,
“MX80 Router Clearance
Requirements for Airflow and
Hardware Maintenance” on page 26,
“MX80 Router Cabinet Requirements
and Specifications” on page 27

If a rack is used, secure rack to floor and building “MX80 Router Rack Requirements”
structure. on page 24

Acquire cables and connectors.

Copyright © 2010, Juniper Networks, Inc. 23

MX80 3D Universal Edge Router Hardware Guide

Table 9: MX80 Site Preparation Checklist (continued)

Item or Task For More Information Performed By Date

Locate sites for connection of system “MX80 Router Grounding

grounding. Specifications” on page 139

Measure distance between external power

sources and router installation site.

Calculate the optical power budget and optical “Calculating Power Budget and
power margin. Power Margin for Fiber-Optic Cables”
on page 154

Related Topics • MX80 Installation Summary on page 29

• Tools Required to Install the MX80 Chassis in the Rack on page 37

• Installing the MX80 Chassis in the Rack on page 38

MX80 Router Rack Requirements

The router can be installed in a rack. Many types of racks are acceptable, including
four-post (telco) racks and open-frame racks. An example of an open-frame rack appears
in Figure 15 on page 26. Table 10 on page 24 summarizes rack requirements and
specifications for the MX80 router.

Table 10: MX80 Rack Requirements and Specifications

Rack Requirement Guidelines

Rack type and mounting bracket hole Use a four-post rack or a two-post rack. You can mount the router on any four-post
spacing or two-post rack that provides bracket holes or hole patterns spaced at 1 U
(1.75-in./4.44-cm) increments and that meets the size and strength requirements
specified in this table.

A U is the standard rack unit defined in Cabinets, Racks, Panels, and Associated
Equipment (document number EIA-310–D) published by the Electronics Industry
Association (http://www.eia.org).

24 Copyright © 2010, Juniper Networks, Inc.

 Chapter 3: Preparing the Site for MX80 Router Installation

Table 10: MX80 Rack Requirements and Specifications (continued)

Rack Requirement Guidelines

Rack size and strength • Ensure that the rack is a 19-in. rack as defined in Cabinets, Racks, Panels, and
Associated Equipment (document number EIA-310–D) published by the Electronics
Industry Association (http://www.eia.org).
• Ensure that the rack is one of the following standard lengths:
• 23.62 in. (600 mm)
• 30.0 in. (762 mm)
• 31.5 in. (800 mm)

• The rack rails must be spaced widely enough to accommodate the router chassis's
external dimensions: 3.5 in. (8.9 cm) high, 21.75 in. (55.2 cm) deep, and
17.4 in. (44.2 cm) wide. The outer edges of the mounting brackets extend the width
to 19.2 in. (48.7 cm). The spacing of rails and adjacent racks must also allow for the
clearances around the router and rack that are specified in “MX80 Router Clearance
Requirements for Airflow and Hardware Maintenance” on page 26.
• The MX80 router ships with the mounting brackets installed in the front-mount
position. You can also move the brackets to the center-mount position. For
instructions about moving the mounting hardware, see “Moving the Mounting
Brackets for Center-Mounting the MX80 Router” on page 35.
• The chassis height of 3.5 in. (8.9 cm) is approximately 2 U. A U is the standard rack
unit defined in Cabinets, Racks, Panels, and Associated Equipment (document number
EIA-310-D) published by the Electronics Industry Association. You can stack several
routers in a cabinet that has sufficient usable vertical space. Each router requires
2 U.
• The rack must be strong enough to support the weight of the fully configured router,
up to 30 lb (13.6 kg).
• Ensure that the spacing of rails and adjacent racks allows for the proper clearance
around the router and rack as specified in “MX80 Router Clearance Requirements
for Airflow and Hardware Maintenance” on page 26.

Rack connection to the building • Secure the rack to the building structure.
structure • If earthquakes are a possibility in your geographical area, secure the rack to the
floor.
• Secure the rack to the ceiling brackets as well as wall or floor brackets for maximum
stability.

Copyright © 2010, Juniper Networks, Inc. 25

MX80 3D Universal Edge Router Hardware Guide

Figure 15: Typical Open-Frame Rack

Related Topics • MX80 Site Preparation Checklist on page 23

• MX80 Installation Summary on page 29

• Installing the MX80 Chassis in the Rack on page 38

MX80 Router Clearance Requirements for Airflow and Hardware Maintenance

When planning the installation site, allow sufficient clearance around the rack (see Figure
16 on page 27):

• For the cooling system to function properly, the airflow around the chassis must be
unrestricted. Allow at least 6 in. (15.2 cm) of clearance between side-cooled routers.
Allow 2.8 in. (7 cm) between the side of the chassis and any non-heat-producing
surface such as a wall.

• For service personnel to remove and install hardware components, there must be
adequate space at the front and back of the router. At least 24 in. (61 cm) is required
both in front of and behind the router. NEBS GR-63 recommends that you allow at
least 30 in. (72.6 cm) in front of the rack and 24 in. (61.0 cm) behind the router.

26 Copyright © 2010, Juniper Networks, Inc.

 Chapter 3: Preparing the Site for MX80 Router Installation

Figure 16: MX80 Chassis Dimensions and Clearance Requirements

22.7"
30" (76.2 cm) (57.6 cm)
clearance recommended
24" (61 cm)
for maintenance 20.2"
clearance required
(51.3 cm)

Front of chassis Rear of chassis

19.2" 17.4"
(48.7 cm) (44.2 cm)

g005017
Cable management bracket
Front-mounting flange

Related Topics • MX80 Site Preparation Checklist on page 23

• MX80 Router Rack Requirements on page 24

• MX80 Installation Summary on page 29

• Installing the MX80 Chassis in the Rack on page 38

• MX80 Router Physical Specifications on page 135

MX80 Router Cabinet Requirements and Specifications

Table 11 on page 27 summarizes cabinet requirements and specifications for MX80

routers.

Table 11: Cabinet Requirements and Specifications for an MX80 Router

Cabinet Requirement Guidelines for the MX80 Router

Cabinet size and clearance • The minimum-sized cabinet that can accommodate the router is 19-in. (482-mm)
wide and 23.62-in. (600-mm) deep. A cabinet larger than the minimum requirement
provides better airflow and reduces the chance of overheating. If you provide adequate
cooling air and airflow clearance, you can stack several routers in a cabinet that has
sufficient usable vertical space. Each router requires 2 U.
A U is the standard rack unit defined in Cabinets, Racks, Panels, and Associated
Equipment (document number EIA-310–D) published by the Electronics Industry
Association (http://www.eia.org).
• With adequate cooling air and airflow clearance, you can stack multiple MX80 routers
in a cabinet with a four-post rack. In all cases, the rack must meet the strength
requirements to support the weight.
• The minimum total clearance inside the cabinet is 30.7 in. (780 mm) between the
inside of the front door and the inside of the rear door.

Copyright © 2010, Juniper Networks, Inc. 27

MX80 3D Universal Edge Router Hardware Guide

Table 11: Cabinet Requirements and Specifications for an MX80 Router (continued)
Cabinet Requirement Guidelines for the MX80 Router

Cabinet airflow requirements When you install the router in a cabinet, you must ensure that ventilation through the
cabinet is sufficient to prevent overheating. Consider the following requirements to
when planning for chassis cooling:

• Airflow must always be from front to back with respect to the rack. If the device has
side to rear airflow, then provisions must be made to ensure that fresh air from the
front of the rack is supplied to the inlets, and exhaust exits the rear of the rack. The
device must not interfere with the cooling of other systems in the rack. Fillers must
be used as appropriate in the rack to ensure there is no recirculation of heated exhaust
air back to the front of the rack. Care must also be taken around cables to ensure no
leakage of air in situations where recirculation may result.
• Ensure that the cabinet allows the chassis hot exhaust air to exit from the cabinet
without recirculating into the router. An open cabinet (without a top or doors) that
employs hot air exhaust extraction from the top allows the best airflow through the
chassis. If the cabinet contains a top or doors, perforations in these elements assist
with removing the hot air exhaust. For an illustration of chassis airflow, see Figure 17
on page 28.
• Ensure that the cool air supply you provide through the cabinet can adequately
dissipate the thermal output of the router.
• Route and dress all cables to minimize the blockage of airflow to and from the chassis.
• Ensure that the spacing of rails and adjacent racks allows for the proper clearance
around the router and rack as specified in “MX80 Router Clearance Requirements
for Airflow and Hardware Maintenance” on page 26.
• Install the router as close as possible to the front of the cabinet so that the chassis
just clears the inside of the front door. This maximizes the clearance in the rear of the
cabinet for critical airflow.

Figure 17: Airflow Through Chassis

Front view
airflow
g005016

Power supply exhaust Fan tray/

air filter

Related Topics • MX80 Cooling System Description on page 8

• MX80 Site Preparation Checklist on page 23

• MX80 Installation Summary on page 29

• Installing the MX80 Chassis in the Rack on page 38

28 Copyright © 2010, Juniper Networks, Inc.

CHAPTER 4

Overview of MX80 Router Installation

• MX80 Installation Summary on page 29

MX80 Installation Summary

To install the MX80 router:

1. Prepare your installation site.

See “MX80 Site Preparation Checklist” on page 23.

2. Review the safety guidelines and warnings.

• General Safety Guidelines for M Series, MX Series, and T Series Routers on page 101

• General Safety Warnings for M Series, MX Series, and T Series Routers on page 102

3. Unpack the router and verify the parts.

a. “Unpacking the MX80 Router” on page 31

b. “Verifying the MX80 Router Parts Received” on page 32

4. Install the mounting hardware.

See “Moving the Mounting Brackets for Center-Mounting the MX80 Router” on
page 35.

5. Lift the router onto the rack.

See “Installing the MX80 Chassis in the Rack” on page 38.

6. Connect cables to the network and external devices:

• Connecting the MX80 Router to Management Devices on page 41

• Connecting Interface Cables to the MX80 Router on page 43

7. Connect the grounding cable.

See “Grounding the MX80 Router” on page 46.

8. Connect the AC power cord or DC power cables.

• Connecting Power to an AC-Powered MX80 Router on page 47

• Connecting Power to a DC-Powered MX80 Router on page 49

Copyright © 2010, Juniper Networks, Inc. 29

MX80 3D Universal Edge Router Hardware Guide

9. Power on the router:

• Powering On an AC-Powered MX80 Router on page 47

• Powering On a DC-Powered MX80 Router on page 51

10. Perform the initial system configuration.

See “Initially Configuring the MX80 Router” on page 55.

Related Topics • MX80 Router Rack Requirements on page 24

• MX80 Router Clearance Requirements for Airflow and Hardware Maintenance on

page 26

• MX80 Router Cabinet Requirements and Specifications on page 27

30 Copyright © 2010, Juniper Networks, Inc.

CHAPTER 5

Unpacking the MX80 Router

• Tools and Parts Required to Unpack the MX80 Router on page 31

• Unpacking the MX80 Router on page 31
• Verifying the MX80 Router Parts Received on page 32

Tools and Parts Required to Unpack the MX80 Router

To unpack the router and prepare for installation, you need the following tools:

• Blank panels to cover any slots not occupied by a component

Related Topics • MX80 Site Preparation Checklist on page 23

• MX80 Installation Summary on page 29

• Unpacking the MX80 Router on page 31

• Verifying the MX80 Router Parts Received on page 32

Unpacking the MX80 Router

The MX80 router is shipped in a cardboard carton and secured with foam packing material.
The carton also contains an accessory box and quick start instructions.

NOTE: The router is maximally protected inside the shipping carton. Do not unpack it
until you are ready to begin installation.

To unpack the router:

1. Move the shipping carton to a staging area as close to the installation site as possible,
but where you have enough room to remove the router.

2. Position the carton so that the arrows are pointing up.

3. Open the top flaps on the shipping carton.

4. Remove the accessory box, and verify the contents against the parts inventory on
the label attached to the carton.

Copyright © 2010, Juniper Networks, Inc. 31

MX80 3D Universal Edge Router Hardware Guide

5. Pull out the packing material holding the router in place.

6. Verify the contents of the carton against the packing list included with the router.

7. Save the shipping carton and packing materials in case you later need to move or
ship the router.

Related Topics • MX80 Site Preparation Checklist on page 23

• MX80 Installation Summary on page 29

• Tools and Parts Required to Unpack the MX80 Router on page 31

• Verifying the MX80 Router Parts Received on page 32

Verifying the MX80 Router Parts Received

A packing list is included in each shipment. Check the parts in the shipment against the
items on the packing list. The packing list specifies the part numbers and descriptions of
each part in your order.

If any part is missing, contact a customer service representative.

A fully configured router contains the router chassis with installed components, listed in
Table 12 on page 32, and an accessory box, which contains the parts listed in Table 13 on
page 33. The parts shipped with your router can vary depending on the configuration you
ordered.

Table 12: Parts List for a Fully Configured Router

Component Quantity

Chassis 1

Air filter 1

MICs (modular chassis only) Up to 2

DC power supplies 1 or 2

AC power supplies 1 or 2

Fan tray 1

Cable management brackets 2

Quick start installation instructions 1

Blank panels for slots without components installed One blank panel for each slot not
occupied by a component

32 Copyright © 2010, Juniper Networks, Inc.

 Chapter 5: Unpacking the MX80 Router

Table 13: Accessory Box Parts List

Part Quantity

Screws to mount chassis 4

Screws to secure the ground cable lug 2

Ground terminal lug, 14 AWG, sized for #10 screw 1

DC power ring terminal lugs, 16-14 AWG, sized for #6 9

screw

Label, “Small Parts Enclosed”, MX80 1

Label, accessories contents, MX80 1

USB flash drive with JUNOS Software 1

Read me first document 1

Affidavit for T1 connection 1

Juniper Networks Product Warranty 1

End User License Agreement 1

Documentation addendum card, MX80 1

Document sleeve 1

3 in. x 5 in. pink bag 2

9 in. x 12 in. pink bag, ESD 2

Accessory box, 19 in. x 12 in. x 3 in. 1

Ethernet cable, RJ-45 to DB-9 1

ESD wrist strap with cable 1

Related Topics • MX80 Site Preparation Checklist on page 23

• MX80 Installation Summary on page 29

• Tools and Parts Required to Unpack the MX80 Router on page 31

• Unpacking the MX80 Router on page 31

Copyright © 2010, Juniper Networks, Inc. 33

MX80 3D Universal Edge Router Hardware Guide

34 Copyright © 2010, Juniper Networks, Inc.

CHAPTER 6

Installing the MX80 Router Mounting

Hardware

• Moving the Mounting Brackets for Center-Mounting the MX80 Router on page 35

Moving the Mounting Brackets for Center-Mounting the MX80 Router

Two removable mounting brackets are attached to the mounting holes closest to the
front of the chassis (see Figure 18 on page 35). You can move the pair of brackets to
another position on the side of the chassis for center-mounting the router.

To move the mounting brackets from the front of the chassis toward the center of the
chassis (see Figure 19 on page 36):

1. Remove the four screws at the top and bottom of the bracket.

2. Pull the bracket away from the chassis.

3. Align the bracket with the two sets of mounting holes located toward the center of
the chassis.

4. Insert the four screws at the top and bottom of the bracket and tighten each partially.

5. Tighten the four screws completely.

6. Repeat the procedure for the other bracket.

Figure 18: Front-Mounting the Brackets on the MX80 Router

g005018

Copyright © 2010, Juniper Networks, Inc. 35

MX80 3D Universal Edge Router Hardware Guide

Figure 19: Center-Mounting the Brackets on the MX80 Router

g005019
Related Topics • MX80 Site Preparation Checklist on page 23

• MX80 Installation Summary on page 29

• Unpacking the MX80 Router on page 31

• Installing the MX80 Chassis in the Rack on page 38

36 Copyright © 2010, Juniper Networks, Inc.

CHAPTER 7

Installing the MX80 Router

• Tools Required to Install the MX80 Chassis in the Rack on page 37

• Installing the MX80 Chassis in the Rack on page 38
• Installing the MX80 Cable Management Bracket on page 39

Tools Required to Install the MX80 Chassis in the Rack

To install the router, you need the following tools and parts:

• Phillips (+) screwdriver, number 2

• ESD grounding wrist strap

Related Topics • MX80 Site Preparation Checklist on page 23

• MX80 Installation Summary on page 29

• Installing the MX80 Chassis in the Rack on page 38

Copyright © 2010, Juniper Networks, Inc. 37

MX80 3D Universal Edge Router Hardware Guide

Installing the MX80 Chassis in the Rack

To install the router in the rack (see Figure 20 on page 39 and Figure 21 on page 39):

CAUTION: If you are installing more than one router in a rack, install the lowest one
first. Installing a router in an upper position in a rack or cabinet requires a lift.

CAUTION: Before front mounting the router in a rack, have a qualified technician verify
that the rack is strong enough to support the router's weight and is adequately supported
at the installation site.

CAUTION: Lifting the chassis and mounting it in a rack requires two people (one person
to hold the router in place and a second person to install the screws). The chassis weighs
approximately 30 lb (13.6 kg).

1. Ensure that the rack is in its permanent location and is secured to the building. Ensure
that the installation site allows adequate clearance for both airflow and maintenance.

2. Position the router in front of the rack or cabinet.

3. Hold onto the bottom of the chassis and carefully lift it so that the mounting brackets
contact the rack rails.

WARNING: To prevent injury, keep your back straight and lift with your legs, not your
back. Avoid twisting your body as you lift. Balance the load evenly and be sure that your
footing is solid.

4. Align the mounting brackets with the holes in the rack rails.

5. Install a mounting screw into each of the open mounting holes aligned with the rack,
starting from the bottom.

6. Visually inspect the alignment of the router. If the router is installed properly in the
rack, all the mounting screws on one side of the rack should be aligned with the
mounting screws on the opposite side and the router should be level.

38 Copyright © 2010, Juniper Networks, Inc.

 Chapter 7: Installing the MX80 Router

Figure 20: Installing the Front-Mounted Router in the Rack

Mounting rack

Mounting bracket

g005020
Figure 21: Installing the Center-Mounted Router in the Rack

Mounting rack

Mounting bracket
g005044

Related Topics • MX80 Site Preparation Checklist on page 23

• MX80 Installation Summary on page 29

• Unpacking the MX80 Router on page 31

• Tools Required to Install the MX80 Chassis in the Rack on page 37

Installing the MX80 Cable Management Bracket

The cable management bracket attaches to the left side of the router. To install the cable
management bracket (see Figure 22 on page 40):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

2. Position the cable management bracket on the left side of the front of the chassis.

3. Tighten the screws at the bottom and top of the bracket.

Copyright © 2010, Juniper Networks, Inc. 39

MX80 3D Universal Edge Router Hardware Guide

Figure 22: Installing the Cable Management Bracket

g005036
Related Topics • MX80 Site Preparation Checklist on page 23

• MX80 Installation Summary on page 29

• Installing the MX80 Chassis in the Rack on page 38

• Connecting the MX80 Router to Management Devices on page 41

• Connecting Interface Cables to the MX80 Router on page 43

40 Copyright © 2010, Juniper Networks, Inc.

CHAPTER 8

Connecting the MX80 Router

• Tools and Parts Required for MX80 Router Connections on page 41

• Connecting the MX80 Router to Management Devices on page 41
• Connecting Interface Cables to the MX80 Router on page 43

Tools and Parts Required for MX80 Router Connections

To connect the router to management devices and line cards, no tools or parts are
required.

Related Topics • Installing the MX80 Cable Management Bracket on page 39

• Connecting the MX80 Router to Management Devices on page 41

• Connecting Interface Cables to the MX80 Router on page 43

Connecting the MX80 Router to Management Devices

• Connecting the MX80 Router to a Network for Out-of-Band Management on page 41

• Connecting the MX80 Router to a Management Console or Auxiliary Device on page 42

Connecting the MX80 Router to a Network for Out-of-Band Management

To connect to the ETHERNET port on the Routing Engine:

1. Turn off the power to the management device.

2. Plug one end of the Ethernet cable (Figure 23 on page 41 shows the connector) into
the ETHERNET port on the Routing Engine. Figure 24 on page 42 shows the port.

3. Plug the other end of the cable into the network device.

Figure 23: Routing Engine Ethernet Cable Connector

Copyright © 2010, Juniper Networks, Inc. 41

MX80 3D Universal Edge Router Hardware Guide

Figure 24: Ethernet Port

Alarm Routing Console Ethernet
LEDs Engine port port
LED

MX80

System
status
LED ONLINE/
OFFLINE

g005046
ONLINE/ Reset Auxiliary USB Clock
OFFLINE button port port ports 10-Gigabit Ethernet MIC
button

Connecting the MX80 Router to a Management Console or Auxiliary Device

To use a system console to configure and manage the Routing Engine, connect it to the
appropriate CONSOLE port on the front panel. To use a laptop, modem, or other auxiliary
device, connect it to the AUX port on the front panel. Both ports accept a cable with an
RJ-45 connector. One serial cable with an RJ-45 connector and a DB-9 connector is
provided with the router. To connect a device to the CONSOLE port and another device
to the AUX port, you must supply an additional cable.

To connect a management console or auxiliary device:

1. Turn off the power to the console or auxiliary device.

2. Plug the RJ-45 end of the serial cable (Figure 25 on page 42 shows the connector)
into the AUX port or CONSOLE port on the front panel. Figure 26 on page 42 shows
the ports.

3. Plug the female DB-9 end into the device's serial port.

Figure 25: Routing Engine Console and Auxiliary Cable Connector

Figure 26: Auxiliary and Console Ports

Alarm Routing Console Ethernet
LEDs Engine port port
LED

MX80

System
status
LED ONLINE/
OFFLINE
g005046

ONLINE/ Reset Auxiliary USB Clock

OFFLINE button port port ports 10-Gigabit Ethernet MIC
button

Related Topics • Installing the MX80 Cable Management Bracket on page 39

42 Copyright © 2010, Juniper Networks, Inc.

 Chapter 8: Connecting the MX80 Router

• Connecting Interface Cables to the MX80 Router on page 43

• Initially Configuring the MX80 Router on page 55

Connecting Interface Cables to the MX80 Router

To connect the physical interfaces to the network (see Figure 27 on page 44):

1. Have ready a length of the type of cable used by the component. For MIC cable
specifications, see the MX Series 3D Universal Edge Routers Line Card Guide.

2. Remove the rubber safety plug from the cable connector port.

WARNING: Do not look directly into a fiber-optic transceiver or into the ends of
fiber-optic cables. Fiber-optic transceivers and fiber-optic cable connected to a
transceiver emit laser light that can damage your eyes.

CAUTION: Do not leave a fiber-optic transceiver uncovered except when inserting or

removing cable. The safety cap keeps the port clean and prevents accidental exposure
to laser light.

3. Insert the cable connector into the cable connector port on the faceplate.

NOTE: The XFP cages and optics on the components are industry standard parts that
have limited tactile feedback for insertion of optics and fiber. You need to insert the
optics and fiber firmly until the latch is securely in place.

4. Arrange the cable to prevent it from dislodging or developing stress points. Secure
the cable so that it is not supporting its own weight as it hangs to the floor. Place
excess cable out of the way in a neatly coiled loop.

CAUTION: Avoid bending fiber-optic cable beyond its minimum bend radius. An arc
smaller than a few inches in diameter can damage the cable and cause problems that
are difficult to diagnose.

CAUTION: Do not let fiber-optic cable hang free from the connector. Do not allow
fastened loops of cable to dangle, which stresses the cable at the fastening point.

Copyright © 2010, Juniper Networks, Inc. 43

MX80 3D Universal Edge Router Hardware Guide

Figure 27: Attaching a Cable to a MIC

g004928
Fiber-optic cable

Related Topics • Installing the MX80 Cable Management Bracket on page 39

• Connecting the MX80 Router to Management Devices on page 41

• Initially Configuring the MX80 Router on page 55

44 Copyright © 2010, Juniper Networks, Inc.

CHAPTER 9

Grounding and Providing Power to the

MX80 Router

• Tools and Parts Required for MX80 Router Grounding and Power
Connections on page 45
• Grounding the MX80 Router on page 46
• Connecting Power to an AC-Powered MX80 Router on page 47
• Powering On an AC-Powered MX80 Router on page 47
• Connecting Power to a DC-Powered MX80 Router on page 49
• Powering On a DC-Powered MX80 Router on page 51

Tools and Parts Required for MX80 Router Grounding and Power Connections

To ground and provide power to the router, you need the following tools and parts:

• Phillips (+) screwdrivers, numbers 1 and 2

• 2.5-mm flat-blade (–) screwdriver

• Torque-controlled driver, with a maximum torque capacity of 6 lb-in., for tightening

screws to terminals on each power supply on a DC-powered router.

CAUTION: The maximum torque rating of the terminal screws on the DC power supply
is 6 lb-in. (0.7 Nm). The terminal screws may be damaged if excessive torque is applied.
Use only a torque-controlled driver to tighten screws on the DC power supply terminals.
Use an appropriately sized driver, with a maximum torque capacity of 6 lb-in. or less.
Ensure that the driver is undamaged and properly calibrated and that you have been
trained in its use. You may wish to use a driver that is designed to prevent overtorque
when the preset torque level is achieved.

• Wire cutters

• Electrostatic discharge (ESD) grounding wrist strap

Related Topics • Grounding the MX80 Router on page 46

• MX80 Router Grounding Specifications on page 139

Copyright © 2010, Juniper Networks, Inc. 45

MX80 3D Universal Edge Router Hardware Guide

Grounding the MX80 Router

You ground the router by connecting a grounding cable to earth ground and then attaching
it to the chassis grounding points using two SAE 10-32 screws. You must provide the
grounding cables (the cable lugs are supplied with the router). For grounding cable
specifications, see “MX80 Router Grounding Cable Specifications” on page 140. To ground
the MX80 router:

1. Verify that a licensed electrician has attached the cable lug provided with the router
to the grounding cable.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to an approved site ESD grounding point. See the instructions for
your site.

3. Ensure that all grounding surfaces are clean and brought to a bright finish before
grounding connections are made.

4. Connect the grounding cable to a proper earth ground.

5. Detach the ESD grounding strap from the site ESD grounding point.

6. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

7. Place the grounding cable lug over the grounding points on the upper rear of the
chassis (see Figure 28 on page 46).

8. Secure the grounding cable lug with the screws. The holes are sized for SAE 10-32
screws.

9. Dress the grounding cable and verify that it does not touch or block access to router
components, and that it does not drape where people could trip on it.

Figure 28: Grounding Points on the MX80 Router

Protective
earthing terminal
(grounding points)

CLOCK
g005009

SYNC

Related Topics • Tools and Parts Required for MX80 Router Grounding and Power Connections on
page 45

• Connecting Power to an AC-Powered MX80 Router on page 47

46 Copyright © 2010, Juniper Networks, Inc.

 Chapter 9: Grounding and Providing Power to the MX80 Router

• Connecting Power to a DC-Powered MX80 Router on page 49

Connecting Power to an AC-Powered MX80 Router

CAUTION: Do not mix AC and DC power supplies within the same router. Damage to
the router might occur.

You connect AC power to the router by attaching power cords from the AC power sources
to the AC appliance inlets located on the power supplies.

To connect the AC power cords to the router for each power supply:

1. Locate power cords that have a plug appropriate for your geographical location. For
more information, see “Connecting an MX80 AC Power Supply Cord” on page 88.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

3. Move the AC input switch next to the appliance inlet on the power supply to the
off (O) position.

4. Connect the power cord to the power supply.

5. Insert the power cord plug into an external AC power source receptacle.

NOTE: Each power supply must be connected to a dedicated AC power feed and a
dedicated customer site circuit breaker. We recommend that you use a dedicated
customer site circuit breaker rated for 15 A (110 VAC) minimum, or as required by local
code.

6. Route the power cord appropriately. Verify that the power cord does not block the
air exhaust and access to router components, or drape where people could trip on
it.

7. Repeat Step 1 through Step 6 for the remaining power supply.

Related Topics • Tools and Parts Required for MX80 Router Grounding and Power Connections on
page 45

• Powering On an AC-Powered MX80 Router on page 47

• MX80 Router Grounding Specifications on page 139

Powering On an AC-Powered MX80 Router

To power on an AC-powered router:

1. Verify that the power supplies are fully inserted in the chassis.

2. Verify that each AC power cord is securely inserted into its appliance inlet.

Copyright © 2010, Juniper Networks, Inc. 47

MX80 3D Universal Edge Router Hardware Guide

3. Verify that an external management device is connected to one of the Routing Engine
ports (AUX, CONSOLE, or ETHERNET).

4. Turn on the power to the external management device.

5. Switch on the dedicated customer site circuit breakers for the power supplies. Follow
the instructions for your site.

6. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

7. Switch the AC input switch on each power supply to the on ( | ) position and observe
the status LED on each power supply faceplate. If an AC power supply is correctly
installed and functioning normally, the status LED above each AC input switch lights
steadily green.

If the status LED on the power supply is lit red, the power supply is not functioning
normally. Repeat the installation and cabling procedures.

NOTE: After powering off a power supply, wait at least 60 seconds before turning it
back on. After powering on a power supply, wait at least 60 seconds before turning it
off.
If the system is completely powered off when you power on the power supply, the
Routing Engine boots as the power supply completes its startup sequence. If the Routing
Engine finishes booting and you need to power off the system again, first issue the CLI
request system halt command.

After a power supply is powered on, it can take up to 60 seconds for status
indicators—such as the status LEDs on the power supply and the show chassis command
display—to indicate that the power supply is functioning normally. Ignore error indicators
that appear during the first 60 seconds.

8. On the external management device connected to the Routing Engine, monitor the
startup process to verify that the system has booted properly.

Related Topics • Tools and Parts Required for MX80 Router Grounding and Power Connections on
page 45

• Connecting Power to an AC-Powered MX80 Router on page 47

• MX80 Router Grounding Specifications on page 139

• request system halt

• show chassis power

48 Copyright © 2010, Juniper Networks, Inc.

 Chapter 9: Grounding and Providing Power to the MX80 Router

Connecting Power to a DC-Powered MX80 Router

CAUTION: Do not mix AC and DC power supplies within the same router. Damage to
the router might occur.

WARNING: Before performing DC power procedures, ensure that power is removed

from the DC circuit. To ensure that all power is off, locate the circuit breaker on the
panel board that services the DC circuit, switch the circuit breaker to the off position,
and tape the switch handle of the circuit breaker in the off position.

You connect DC power to the router by attaching power cables from the external DC
power sources to the terminal on the power supply faceplate. You must provide the
power cables (the cable lugs are supplied with the router). For power cable specifications,
see “DC Power Cable Specifications for the MX80 Router” on page 149.

To connect the DC source power cables to the router for each power supply:

1. Switch off the dedicated customer site circuit breakers. Ensure that the voltage
across the DC power source cable leads is 0 V and that there is no chance that the
cable leads might become active during installation.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

3. Switch the DC circuit breaker on the power supply faceplate to the off (O) position.

4. Remove the clear plastic cover protecting the terminal on the faceplate.

5. Verify that the DC power cables are correctly labeled before making connections to
the power supply. In a typical power distribution scheme where the return is connected
to chassis ground at the battery plant, you can use a multimeter to verify the
resistance of the –48V and RTN DC cables to chassis ground:

• The cable with very large resistance (indicating an open circuit) to chassis ground
is –48V.

• The cable with very low resistance (indicating a closed circuit) to chassis ground
is RTN.

CAUTION: You must ensure that power connections maintain the proper polarity. The
power source cables might be labeled (+) and (–) to indicate their polarity. There is no
standard color coding for DC power cables. The color coding used by the external DC
power source at your site determines the color coding for the leads on the power cables
that attach to the terminal studs on each power supply.

6. Remove the screws from the terminals.

Copyright © 2010, Juniper Networks, Inc. 49

MX80 3D Universal Edge Router Hardware Guide

7. Secure each power cable lug to the terminal with the screw (see Figure 29 on
page 50). Apply between 5 lb-in. (0.6 Nm) and 6 lb-in. (0.7 Nm) of torque to screw.
Do not overtighten the nut. (Use a number 2 Phillips screwdriver.)

a. Secure the positive (+) DC source power cable lug to the RTN (return) terminal.

b. Secure the negative (–) DC source power cable lug to the –48V (input) terminal.

CAUTION: Ensure that each power cable lug seats flush against the surface of the
terminal block as you are tightening the screws. Ensure that each screw is properly
threaded into the terminal. Applying installation torque to the screw when improperly
threaded may result in damage to the terminal.

CAUTION: You must ensure that power connections maintain the proper polarity. The
power source cables might be labeled (+) and (–) to indicate their polarity. There is no
standard color coding for DC power cables. The color coding used by the external DC
power source at your site determines the color coding for the leads on the power cables
that attach to the terminal studs on each power supply.

NOTE: For information about connecting to DC power sources, see “MX80 Router DC
Power Specifications” on page 146.

8. Replace the clear plastic cover over the terminals on the faceplate.

9. Verify that the power cables are connected correctly, that they are not touching or
blocking access to router components, and that they do not drape where people
could trip on them.

10. If you are installing two power supplies, repeat Steps 3 through 9 for the other power
supply.

Figure 29: Connecting DC Power to the Router

g005006

Related Topics • Tools and Parts Required for MX80 Router Grounding and Power Connections on
page 45

• Powering On a DC-Powered MX80 Router on page 51

50 Copyright © 2010, Juniper Networks, Inc.

 Chapter 9: Grounding and Providing Power to the MX80 Router

• MX80 Router Grounding Specifications on page 139

Powering On a DC-Powered MX80 Router

To power on a DC-powered router:

1. Verify that an external management device is connected to one of the Routing Engine
ports (AUX, CONSOLE, or ETHERNET).

2. Turn on the power to the external management device.

3. Verify that the power supplies are fully inserted in the chassis.

4. Verify that the source power cables are connected to the appropriate terminal: the
positive (+) source cable to the return terminal (labeled RTN) and the negative (–)
source cable to the input terminal (labeled –48V).

5. Switch on the dedicated customer site circuit breakers to provide power to the DC
power cables.

6. Check that the status LED on the power supply faceplate is lit steadily green to verify
that power is present.

7. If power is not present:

• Verify that the fuse is installed correctly, and turn on the breaker at the battery
distribution fuse board or fuse bay.

• Check the voltage with a meter at the terminals of the power supply for correct
voltage level and polarity.

8. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

9. On each of the DC power supplies, switch the DC circuit breaker to the center position
before moving it to the on ( | ) position.

NOTE: The circuit breaker may bounce back to the off (O) position if you move the
breaker too quickly.

Observe the status LED on each power supply faceplate. If a DC power supply is
correctly installed and functioning normally, the status LED lights green steadily.

If the status LED on the power supply is lit red, the power supply is not functioning
normally. Repeat the installation and cabling procedures.

Copyright © 2010, Juniper Networks, Inc. 51

MX80 3D Universal Edge Router Hardware Guide

NOTE: After powering off a power supply, wait at least 60 seconds before turning it
back on. After powering on a power supply, wait at least 60 seconds before turning it
off.
If the system is completely powered off when you power on the power supply, the
Routing Engine boots as the power supply completes its startup sequence. If the Routing
Engine finishes booting and you need to power off the system again, first issue the CLI
request system halt command.

After a power supply is powered on, it can take up to 60 seconds for status
indicators—such as the status LEDs on the power supply and the show chassis command
display—to indicate that the power supply is functioning normally. Ignore error indicators
that appear during the first 60 seconds.

10. On the external management device connected to the Routing Engine, monitor the
startup process to verify that the system has booted properly.

Related Topics • Tools and Parts Required for MX80 Router Grounding and Power Connections on
page 45

• Connecting Power to an AC-Powered MX80 Router on page 47

• MX80 Router Grounding Specifications on page 139

• request system halt

• show chassis power

52 Copyright © 2010, Juniper Networks, Inc.

CHAPTER 10

Powering Off the MX80 Router

• Powering Off the MX80 Router on page 53

Powering Off the MX80 Router

NOTE: After powering off a power supply, wait at least 60 seconds before turning it
back on.

To power off the router:

1. On the external management device connected to the Routing Engine, issue the
request system halt command.

user@host> request system halt

2. Wait until a message appears on the console confirming that the operating system
has halted. For more information about the command, see the Junos System Basics
and Services Command Reference.

3. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

4. Switch the AC input switch on each AC power supply or the DC circuit breaker on
each DC power supply to the off (O) position.

Related Topics • Disconnecting an MX80 AC Power Supply Cord on page 87

• Disconnecting an MX80 DC Power Supply Cable on page 92

• request system halt

Copyright © 2010, Juniper Networks, Inc. 53

MX80 3D Universal Edge Router Hardware Guide

54 Copyright © 2010, Juniper Networks, Inc.

CHAPTER 11

Configuring JUNOS Software

• Initially Configuring the MX80 Router on page 55

Initially Configuring the MX80 Router

The MX80 router is shipped with the JUNOS Software preinstalled and ready to be
configured when the MX80 router is powered on. Two 4-GB internal NAND flash devices
(da0 and da1) are located on the base board. The USB storage device (da2) can be
inserted into the slot in the front panel faceplate. The two NAND flash devices act as the
primary boot device (da0) and hard drive (da1).

When the router boots, it first attempts to start the image on the USB flash drive. If a
USB flash drive is not inserted into the router or the attempt otherwise fails, the router
next tries the primary boot device, and then tries the secondary boot device.

You configure the router by issuing JUNOS command-line interface (CLI) commands,
either on a console device attached to the Routing Engine CONSOLE port on the front
panel, or over a telnet connection to a network connected to the Routing Engine
ETHERNET port on the front panel.

Gather the following information before configuring the router:

• Name the router will use on the network

• Domain name the router will use

• IP address and prefix length information for the Ethernet interface

• IP address of a default router

• IP address of a DNS server

• Password for the root user

This procedure connects the router to the network but does not enable it to forward
traffic. For complete information about enabling the router to forward traffic, including
examples, see the JUNOS Software configuration guides.

To configure the software:

1. Verify that the router is powered on.

2. Log in as the “root” user. There is no password.

Copyright © 2010, Juniper Networks, Inc. 55

MX80 3D Universal Edge Router Hardware Guide

3. Start the CLI.

root# cli
root@>

4. Enter configuration mode.

cli> configure
[edit]
root@#

5. Configure the name of the router. If the name includes spaces, enclose the name in
quotation marks (“ ”).

[edit]
root@# set system host-name host-name

6. Create a management console user account.

[edit]
root@# set system login user user-name authentication plain-text-password
New password: password
Retype new password: password

7. Set the user account class to super-user.

[edit]
root@# set system login user user-name class super-user

8. Configure the router’s domain name.

[edit]
root@# set system domain-name domain-name

9. Configure the IP address and prefix length for the router’s Ethernet interface.

[edit]
root@# set interfaces fxp0 unit 0 family inet address address/prefix-length

10. Configure the IP address of a backup router, which is used only while the routing
protocol is not running.

[edit]
root@# set system backup-router address

11. Configure the IP address of a DNS server.

[edit]
root@# set system name-server address

12. Set the root authentication password by entering either a clear-text password, an
encrypted password, or an SSH public key string (DSA or RSA).

[edit]
root@# set system root-authentication plain-text-password
New password: password
Retype new password: password

or

[edit]
root@# set system root-authentication encrypted-password encrypted-password

or

56 Copyright © 2010, Juniper Networks, Inc.

 Chapter 11: Configuring JUNOS Software

[edit]
root@# set system root-authentication ssh-dsa public-key

or

[edit]
root@# set system root-authentication ssh-rsa public-key

13. (Optional) Configure the static routes to remote subnets with access to the
management port. Access to the management port is limited to the local subnet.
To access the management port from a remote subnet, you need to add a static
route to that subnet within the routing table. For more information about static
routes, see the Junos System Basics Configuration Guide.

[edit]
root@# set routing-options static route remote-subnet next-hop destination-IP retain
no-readvertise

14. Configure the telnet service at the [edit system services] hierarchy level.

[edit]
root@# set system services telnet

15. (Optional) Display the configuration to verify that it is correct.

[edit]
root@# show
system {
host-name host-name;
domain-name domain-name;
backup-router address;
root-authentication {
authentication-method (password | public-key);
}
name-server {
address;
}
}
interfaces {
fxp0 {
unit 0 {
family inet {
address address/prefix-length;
}
}
}
}

16. Commit the configuration to activate it on the router.

[edit]
root@# commit

17. (Optional) Configure additional properties by adding the necessary configuration

statements. Then commit the changes to activate them on the router.

[edit]
root@host# commit

18. When you have finished configuring the router, exit configuration mode.

Copyright © 2010, Juniper Networks, Inc. 57

MX80 3D Universal Edge Router Hardware Guide

[edit]
root@host# exit
root@host>

Related Topics • Connecting the MX80 Router to Management Devices on page 41

• Powering On an AC-Powered MX80 Router on page 47

• Powering On a DC-Powered MX80 Router on page 51

58 Copyright © 2010, Juniper Networks, Inc.

PART 3

Hardware Maintenance, Troubleshooting,

and Replacement Procedures
• Maintaining MX80 Router Hardware Components on page 61
• Troubleshooting MX80 Hardware Components on page 67
• Replacing MX80 Hardware Components on page 73

Copyright © 2010, Juniper Networks, Inc. 59

MX80 3D Universal Edge Router Hardware Guide

60 Copyright © 2010, Juniper Networks, Inc.

CHAPTER 12

Maintaining MX80 Router Hardware

Components

• Tools and Parts Required to Maintain the MX80 Router on page 61

• Routine Maintenance Procedures for the MX80 Router on page 61
• Maintaining the MX80 Air Filter on page 62
• Maintaining the MX80 Fan Tray on page 62
• Maintaining the MX80 MICs on page 63
• Maintaining Cables That Connect to MX80 MICs on page 64
• Maintaining the MX80 Power Supplies on page 65
• Maintaining the MX80 Routing Engine on page 66

Tools and Parts Required to Maintain the MX80 Router

To maintain hardware components, you need the following tools and parts:

• ESD grounding wrist strap

Related Topics • Routine Maintenance Procedures for the MX80 Router on page 61

Routine Maintenance Procedures for the MX80 Router

Purpose For optimum router performance, perform preventive maintenance procedures.

Action • Inspect the installation site for moisture, loose wires or cables, and excessive dust.
Make sure that airflow is unobstructed around the router and into the air intake vents.

• Check the status-reporting devices on the font panel—System alarms and LEDs.

Related Topics • Tools and Parts Required to Maintain the MX80 Router on page 61

• Maintaining the MX80 Air Filter on page 62

• Maintaining the MX80 Fan Tray on page 62

• Maintaining the MX80 MICs on page 63

Copyright © 2010, Juniper Networks, Inc. 61

MX80 3D Universal Edge Router Hardware Guide

• Maintaining the MX80 Power Supplies on page 65

• Maintaining the MX80 Routing Engine on page 66

Maintaining the MX80 Air Filter

Purpose For optimum cooling, verify the condition of the air filter.

Action • Regularly inspect the air filter. A dirty air filter restricts airflow in the unit, producing a
negative effect on the ventilation of the chassis. The filter degrades over time. You
must replace the filter every 6 months.

CAUTION: Always keep the air filter in place while the router is operating. Because the
fans are very powerful, they could pull small bits of wire or other materials into the
router through the unfiltered air intake. This could damage the router components.

• Use spare filters within 1 year of manufacture. Check the date of manufacture printed
on the filter. Store spare air filters in a dark, cool, and dry place. Storing air filters at
higher temperatures, or where they can be exposed to ultraviolet (UV) radiation,
hydrocarbon emissions, or vapors from solvents, can significantly reduce their life.

Related Topics • MX80 Cooling System Description on page 8

• Replacing an MX80 Air Filter on page 73

Maintaining the MX80 Fan Tray

Purpose For optimum cooling, verify the condition of the fans.

Action • Monitor the status of the fans. A fan tray contains multiple fans that work in unison to
cool the router components. If one fan fails, the router adjusts the speed of the
remaining fans to maintain proper cooling. A red alarm is triggered when a fan fails,
and a yellow alarm and red alarm is triggered when a fan tray is removed.

• To display the status of the cooling system, issue the show chassis environment
command. The output is similar to the following:
user@host> show chassis environment

Class Item Status Measurement

Temp PEM 0 OK 45 degrees C / 113 degrees F
PEM 1 OK 45 degrees C / 113 degrees F
RE 0 Intake OK 33 degrees C / 91 degrees F
RE 0 Front Exhaust OK 38 degrees C / 100 degrees F
RE 0 Rear Exhaust OK 38 degrees C / 100 degrees F
Routing Engine OK 33 degrees C / 91 degrees F
Routing Engine CPU OK 54 degrees C / 129 degrees F
TFEB 0 QX 0 TSen OK 44 degrees C / 111 degrees F
TFEB 0 QX 0 Chip OK 47 degrees C / 116 degrees F
TFEB 0 LU 0 TSen OK 44 degrees C / 111 degrees F

62 Copyright © 2010, Juniper Networks, Inc.

 Chapter 12: Maintaining MX80 Router Hardware Components

TFEB 0 LU 0 Chip OK 50 degrees C / 122 degrees F

TFEB 0 MQ 0 TSen OK 44 degrees C / 111 degrees F
TFEB 0 MQ 0 Chip OK 49 degrees C / 120 degrees F
TFEB 0 TBB PFE TSen OK 37 degrees C / 98 degrees F
TFEB 0 TBB PFE Chip OK 50 degrees C / 122 degrees F
TFEB 0 TFEB PCIE TSen OK 45 degrees C / 113 degrees F
TFEB 0 TFEB PCIE Chip OK 68 degrees C / 154 degrees F
Fans Fan 1 OK Spinning at intermediate-speed

Fan 2 OK Spinning at intermediate-speed

Fan 3 OK Spinning at intermediate-speed

Fan 4 OK Spinning at intermediate-speed

Fan 5 OK Spinning at intermediate-speed

Related Topics • MX80 Cooling System Description on page 8

• Troubleshooting the MX80 Fan Tray on page 69

• Replacing an MX80 Fan Tray on page 75

• show chassis environment

Maintaining the MX80 MICs

Purpose For optimum router performance, verify the condition of the MICs.

Action On a regular basis:

• Check the LEDs on MIC faceplates. The meaning of the LED states differ for various
MICs. For more information, see the MX Series 3D Universal Edge Routers Line Card
Guide. If the router detects a MIC failure, the router generates an alarm message to be
sent to the Routing Engine.

• Issue the CLI show chassis fpc pic-status command. The MIC slots in the modular MX80
router are numbered 1/MIC 0 and 1/MIC 1. The fixed MIC is numbered 0/MIC 0.

user@host> show chassis fpc pic-status

Slot 0 Online
PIC 0 Online 4x 10GE XFP
PIC 2 Online 1x 10GE XFP
PIC 3 Online 1x 10GE XFP
Slot 1 Online
PIC 0 Online 1x 10GE XFP
PIC 1 Online 1x 10GE XFP
PIC 2 Online 1x 10GE XFP
PIC 3 Online 1x 10GE XFP

Related Topics • MX80 Modular Interface Card Description on page 13

• MX80 Modular Interface Card LEDs on page 15

• Maintaining Cables That Connect to MX80 MICs on page 64

Copyright © 2010, Juniper Networks, Inc. 63

MX80 3D Universal Edge Router Hardware Guide

• Troubleshooting the MX80 MICs on page 70

• Replacing an MX80 MIC on page 76

• show chassis fpc

Maintaining Cables That Connect to MX80 MICs

Purpose For optimum router performance, verify the condition of the cables that connect to the
MICs.

Action On a regular basis:

• Use the cable management bracket to support cables and prevent cables from
dislodging or developing stress points.

• Place excess cable out of the way in the cable management bracket. Do not allow
fastened loops of cable to dangle from the connector or cable management bracket,
because this stresses the cable at the fastening point. Putting fasteners on the loops
helps to maintain their shape.

• Keep the cable connections clean and free of dust and other particles, which can cause
drops in the received power level. Always inspect cables and clean them if necessary
before connecting an interface.

• Label both ends of the cables to identify them.

The following guidelines apply specifically to fiber-optic cables:

• When you unplug a fiber-optic cable, always place a rubber safety plug over the
transceiver on the faceplate and on the end of the cable.

• Anchor fiber-optic cables to avoid stress on the connectors. Be sure to secure fiber-optic
cables so that they do not support their own weight as they hang to the floor. Never
let fiber-optic cable hang free from the connector.

• Avoid bending fiber-optic cable beyond its bend radius. An arc smaller than a few
inches can damage the cable and cause problems that are difficult to diagnose.

• Frequent plugging and unplugging of fiber-optic cable into and out of optical
instruments can cause damage to the instruments that is expensive to repair. Instead,
attach a short fiber extension to the optical equipment. Any wear and tear due to
frequent plugging and unplugging is then absorbed by the short fiber extension, which
is easy and inexpensive to replace.

• Keep fiber-optic cable connections clean. Small microdeposits of oil and dust in the
canal of the transceiver or cable connector could cause loss of light, reducing signal
power and possibly causing intermittent problems with the optical connection.

To clean the transceivers, use an appropriate fiber-cleaning device, such as RIFOCS

Fiber Optic Adaptor Cleaning Wands (part number 946). Follow the directions for the
cleaning kit you use.

After you clean an optical transceiver, make sure that the connector tip of the fiber-optic
cable is clean. Use only an approved alcohol-free fiber-optic cable cleaning kit, such

64 Copyright © 2010, Juniper Networks, Inc.

 Chapter 12: Maintaining MX80 Router Hardware Components

as the Opptex Cletop-S Fiber Cleaner. Follow the directions for the cleaning kit you
use.

Related Topics • MX80 Modular Interface Card Description on page 13

• MX80 Modular Interface Card LEDs on page 15

• Maintaining the MX80 MICs on page 63

• Replacing a Cable on an MX80 MIC on page 83

Maintaining the MX80 Power Supplies

Purpose For optimum router performance, verify the condition of the power supplies.

Action On a regular basis:

• Check the status of the power supplies by issuing the show chassis environment pem
command. The output is similar to the following:
user@host> show chassis environment pem

PEM 0 status:
State Online
Temperature OK
DC Output: OK
PEM 1 status:
State Online
Temperature OK
DC Output: OK

• Make sure that the power and grounding cables are arranged so that they do not
obstruct access to other router components.

• Routinely check the status LEDs on the power supply faceplates and the front panel
to determine if the power supplies are functioning normally.

• Check the alarm LEDs on the front panel. Power supply failure or removal triggers an
alarm that causes one or both of the LEDs to light. You can display the associated error
messages by issuing the show chassis alarms command:

user@host> show chassis alarms

1 alarm currently active

Alarm time Class Description
2010-02-03 13:46:31 PST Major PEM 0 Not OK

• Periodically inspect the site to ensure that the grounding and power cables connected
to the router are securely in place and that there is no moisture accumulating near the
router.

Related Topics • MX80 Power System Description on page 16

• MX80 Power Supply LED on page 18

• Troubleshooting the MX80 Power Supplies on page 70

Copyright © 2010, Juniper Networks, Inc. 65

MX80 3D Universal Edge Router Hardware Guide

• show chassis environment pem

• show chassis alarms

Maintaining the MX80 Routing Engine

Purpose On the MX80 router, the Routing Engine is fixed inside the chassis. For optimum router
performance, verify the condition of the Routing Engine.

Action On a regular basis:

• Check the LEDs on the front panel to view information about the status of the Routing
Engine.

• To check the status of the Routing Engine, issue the show chassis routing-engine
command. The output is similar to the following:
user@host> show chassis routing-engine

Routing Engine status:

Temperature 34 degrees C / 93 degrees F
CPU temperature 52 degrees C / 125 degrees F
DRAM 2048 MB
Memory utilization 18 percent
CPU utilization:
User 1 percent
Background 0 percent
Kernel 3 percent
Interrupt 1 percent
Idle 95 percent
Model RE-MX80
Start time 2010-02-05 10:05:17 PST
Uptime 18 minutes, 59 seconds
Last reboot reason Router rebooted after a normal shutdown.

Load averages: 1 minute 5 minute 15 minute

0.00 0.02 0.07

Related Topics • Maintaining the MX80 Routing Engine on page 66

• Routing Engine Interface Cable Specifications for MX80 Routers on page 156

• show chassis routing-engine

66 Copyright © 2010, Juniper Networks, Inc.

CHAPTER 13

Troubleshooting MX80 Hardware

Components

• Troubleshooting Resources for MX80 Routers on page 67

• Troubleshooting the MX80 Fan Tray on page 69
• Troubleshooting the MX80 MICs on page 70
• Troubleshooting the MX80 Power Supplies on page 70

Troubleshooting Resources for MX80 Routers

• Command-Line Interface on page 67

• Chassis and Interface Alarm Messages on page 67
• Front Panel LEDs on page 68
• Component LEDs on page 68

Command-Line Interface
The JUNOS Software command-line interface (CLI) is the primary tool for controlling
and troubleshooting router hardware, the JUNOS Software, routing protocols, and network
connectivity. CLI commands display information from routing tables, information specific
to routing protocols, and information about network connectivity derived from the ping
and traceroute utilities.

You enter CLI commands on one or more external management devices connected to
ports on the front panel.

For information about using the CLI to troubleshoot the JUNOS Software, see the
appropriate JUNOS Software configuration guide.

Chassis and Interface Alarm Messages

When the Routing Engine detects an alarm condition, it lights the red or yellow alarm
LED on the front panel as appropriate. To view a more detailed description of the alarm
cause, issue the show chassis alarms command:

user@host> show chassis alarms

Copyright © 2010, Juniper Networks, Inc. 67

MX80 3D Universal Edge Router Hardware Guide

There are two classes of alarm messages:

• Chassis alarms—Indicate a problem with a chassis component such as the cooling

system or power supplies.

• Interface alarms—Indicate a problem with a specific network interface.

Front Panel LEDs

The front panel on the router contains LEDs and buttons that allow you to troubleshoot
the router.

LEDs on the front panel include the following:

• Alarm LEDs—Two LEDs located on the left side of the front panel indicate critical and
warning alarms on the MX80 router. The circular LED lights red to indicate a critical
condition that can result in a system shutdown. The triangular LED lights yellow to
indicate a less severe condition that requires monitoring or maintenance.

• System LED—One LED on the left side of the front panel indicates the status of the
MX80 router. The LED is located below the SYS OK label. The LED lights steadily green
when the router is functioning normally and blinks green when the router is transitioning
online.

• Routing Engine LED—One bi-color LED on the left side of the front panel indicates the
status of the Routing Engine. The LED is located below the RE label. The LED is lit
steadily green when the Routing Engine is functioning normally and is lit red when the
Routing Engine has failed.

• Link LEDs—Four LEDs labeled LINK, indicate the status of the ports for the fixed
10-Gigabit Ethernet MIC. The LED is green when the link is active, and is off when there
is no link. The LINK LEDs are located to the right of the port on the front panel.

Component LEDs
The following LEDs are located on various router components and display the status of
those components:

• MIC LEDs—One LED labeled OK/FAIL on each MIC faceplate indicates the MIC’s status.
For more information, see the MX Series 3D Universal Edge Routers Line Card Guide. On
the fixed MX80 router, each RJ-45 port has an additional link LED. The LED is green
when the link is active and is off when there is no link.

• Power supply LEDs—One bi-color LED on each power supply faceplate indicate the
status of that power supply. The LED is lit green when the power supply is functioning
normally and is lit red when the power supply has failed.

Related Topics • Troubleshooting the MX80 Fan Tray on page 69

• Troubleshooting the MX80 MICs on page 70

• Troubleshooting the MX80 Power Supplies on page 70

• ping

68 Copyright © 2010, Juniper Networks, Inc.

 Chapter 13: Troubleshooting MX80 Hardware Components

• traceroute

• show chassis alarms

Troubleshooting the MX80 Fan Tray

Problem The fans in the fan tray are not functioning normally.

Solution Follow these guidelines to troubleshoot the fans:

• Check the alarm LEDs on the front panel.

• Issue the show chassis fan command to get status information about the fans.

user@host> show chassis fan

Item Status RPM Measurement

Fan 1 OK 4560 Spinning at
intermediate-speed
Fan 2 OK 4560 Spinning at
intermediate-speed
Fan 3 OK 4560 Spinning at
intermediate-speed
Fan 4 OK 4560 Spinning at
intermediate-speed
Fan 5 OK 4560 Spinning at
intermediate-speed

• If the red alarm LED on the front panel lights, issue the show chassis alarms command
to get information about the source of an alarm condition.

If the CLI output lists only one fan failure, and the other fans are functioning normally,
the fan is most likely faulty and you must replace the fan tray.

• Place your hand near the exhaust vents at the side of the chassis to determine whether
the fans are pushing air out of the chassis.

• If a fan tray is removed, a yellow alarm and a red alarm occur.

• The following conditions automatically cause the fans to run at full speed and also
trigger the indicated alarm:

• A fan fails (red alarm).

• The router temperature exceeds the “temperature warm” threshold (yellow alarm).

• The temperature of the router exceeds the maximum “temperature hot” threshold
(red alarm and automatic shutdown of the power supplies).

To view the temperature threshold settings, issue the show chassis

temperature-thresholds command.

user@host> show chassis temperature-thresholds

Fan speed Yellow alarm Red alarm

Item Normal High Normal Bad fan Normal
Bad fan
Chassis default 48 54 65 55 75

Copyright © 2010, Juniper Networks, Inc. 69

MX80 3D Universal Edge Router Hardware Guide

65
Routing Engine 55 60 75 65 85
70

Related Topics • MX80 Cooling System Description on page 8

• Maintaining the MX80 Fan Tray on page 62

• Replacing an MX80 Fan Tray on page 75

• show chassis fan

• show chassis alarms

• show chassis temperature-thresholds

Troubleshooting the MX80 MICs

Problem The MICs are not functioning normally.

Solution • Check the status of each port on a MIC by looking at the LED located on the MIC
faceplate. For information about the meaning of LED states on different MICs, see the
MX Series 3D Universal Edge Routers Line Card Guide.

• Check the status of a MIC by issuing the show chassis fpc pic-status CLI command. The
MIC slots in the modular MX80 router are labeled 1/MIC 0 and 1/MIC 1. The fixed MIC
is labeled 0/MIC 0.

user@host> show chassis fpc pic-status

Slot 0 Online
PIC 0 Online 4x 10GE XFP
PIC 2 Online 1x 10GE XFP
PIC 3 Online 1x 10GE XFP
Slot 1 Online
PIC 0 Online 1x 10GE XFP
PIC 1 Online 1x 10GE XFP
PIC 2 Online 1x 10GE XFP
PIC 3 Online 1x 10GE XFP

For further description of the output from the command, see the Junos System Basics
and Services Command Reference.

Related Topics • MX80 Modular Interface Card Description on page 13

• Maintaining the MX80 MICs on page 63

• Replacing an MX80 MIC on page 76

• show chassis fpc

Troubleshooting the MX80 Power Supplies

Problem The power supply is not functioning normally.

70 Copyright © 2010, Juniper Networks, Inc.

 Chapter 13: Troubleshooting MX80 Hardware Components

Solution • Check the LEDs on each power supply faceplate. If a power supply is correctly installed
and functioning normally, the status LED on the power supply lights green steadily.

• Issue the CLI show chassis environment pem command to check the status of installed
power supplies. As shown in the sample output, the value Online in the rows labeled
State indicates that each of the power supplies is functioning normally:

user@host> show chassis environment pem

PEM 0 status:
State Online
Temperature OK
DC Output: OK
PEM 1 status:
State Online
Temperature OK
DC Output: OK

• If a red alarm condition occurs, issue the show chassis alarms command to determine
the source of the problem.

• If all power supplies have failed, the system temperature might have exceeded the
threshold, causing the system to shut down.

NOTE: If the system temperature exceeds the threshold, the JUNOS Software shuts
down all power supplies so that no status is displayed.
The JUNOS Software also can shut down one of the power supplies for other reasons.
In this case, the remaining power supplies provide power to the router, and you can still
view the system status through the CLI or display.

• Check that the AC input switch or DC circuit breaker is in the on ( | ) position and is
receiving power.

• Verify that the source circuit breaker has the proper current rating. Each power supply
must be connected to a separate source circuit breaker.

• Verify that the AC power cord or DC power cables from the power source to the router
are not damaged. If the insulation is cracked or broken, immediately replace the cord
or cable.

• Connect the power supply to a different power source with a new power cord or power
cables. If the power supply status LED indicates that the power supply is not operating
normally, the power supply is the source of the problem. Replace the power supply
with a spare.

Related Topics • MX80 Power System Description on page 16

• MX80 Power Supply LED on page 18

• Maintaining the MX80 Power Supplies on page 65

• Replacing an MX80 AC Power Supply on page 85

Copyright © 2010, Juniper Networks, Inc. 71

MX80 3D Universal Edge Router Hardware Guide

• show chassis environment pem

• show chassis alarms

72 Copyright © 2010, Juniper Networks, Inc.

CHAPTER 14

Replacing MX80 Hardware Components

• Replacing an MX80 Air Filter on page 73

• Replacing an MX80 Fan Tray on page 75
• Replacing an MX80 MIC on page 76
• Replacing a Cable on an MX80 MIC on page 83
• Replacing an MX80 AC Power Supply on page 85
• Replacing an MX80 AC Power Supply Cord on page 87
• Replacing an MX80 DC Power Supply on page 88
• Replacing an MX80 DC Power Supply Cable on page 92
• Replacing an MX80 SFP or XFP Transceiver on page 94

Replacing an MX80 Air Filter

• Removing an MX80 Air Filter on page 73

• Installing an MX80 Air Filter on page 74

Removing an MX80 Air Filter

CAUTION: Do not run the router for more than a few minutes without the air filter in
place.

CAUTION: Always keep the air filter in place while the router is operating, except during
replacement. Because the fans are very powerful, they could pull small bits of wire or
other materials into the router through the unfiltered air intake. This could damage the
router components.

The air filter is installed on the right side of the fan tray. To remove the air filter (see Figure
30 on page 74):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

2. Remove the fan tray as described in “Removing an MX80 Fan Tray” on page 75.

Copyright © 2010, Juniper Networks, Inc. 73

MX80 3D Universal Edge Router Hardware Guide

3. Press the release tab on the rear of the fan tray to release the air filter.

4. Grasp the sides of the air filter, and slide it away from the fan tray faceplate.

Figure 30: Removing the Air Filter

g005039
Air filter
Release
latch

Installing an MX80 Air Filter

The air filter installs on the right side of the fan tray. To install the air filter (see Figure 31
on page 75):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

2. Locate the THIS SIDE MUST FACE OUT label and ensure that the air filter is right side
up.

3. Insert the air filter into the groove located toward the front of the fan tray.

4. Press the tab on the rear of the fan tray to allow the air filter to slide into place.

5. Release the tab to secure the air filter.

74 Copyright © 2010, Juniper Networks, Inc.

 Chapter 14: Replacing MX80 Hardware Components

Figure 31: Installing the Air Filter

Air filter

g005038
Angle the filter
under this tab first.

Related Topics • MX80 Cooling System Description on page 8

• Maintaining the MX80 Air Filter on page 62

• Preventing Electrostatic Discharge Damage to an MX80 Router on page 104

Replacing an MX80 Fan Tray

• Removing an MX80 Fan Tray on page 75

• Installing an MX80 Fan Tray on page 76

Removing an MX80 Fan Tray

NOTE: To prevent overheating, install the replacement fan tray immediately after
removing the existing fan tray.

To remove the fan tray (see Figure 32 on page 76):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

2. Loosen the captive screw on the fan tray faceplate.

3. Grasp the fan tray handle, and pull it out approximately 1 to 3 inches.

WARNING: To avoid injury, keep tools and your fingers away from the fans as you slide
the fan tray out of the chassis. The fans might still be spinning.

Copyright © 2010, Juniper Networks, Inc. 75

MX80 3D Universal Edge Router Hardware Guide

4. Press the latch located on the inside of the fan tray to release it from the chassis.

5. Place one hand under the fan tray to support it, and pull the fan tray completely out
of the chassis.

Figure 32: Removing the Fan Tray

g005028
Installing an MX80 Fan Tray
To install the fan tray (see Figure 33 on page 76):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

2. Grasp the fan tray handle, and insert it straight into the chassis.

3. Tighten the captive screw on the fan tray faceplate to secure it in the chassis.

Figure 33: Installing the Fan Tray

g005027

Related Topics • MX80 Cooling System Description on page 8

• Replacing an MX80 Air Filter on page 73

• Maintaining the MX80 Fan Tray on page 62

• Preventing Electrostatic Discharge Damage to an MX80 Router on page 104

Replacing an MX80 MIC

• Removing an MX80 MIC on page 77

• Installing an MX80 MIC on page 78
• Installing an MX80 Dual-Wide MIC on page 80

76 Copyright © 2010, Juniper Networks, Inc.

 Chapter 14: Replacing MX80 Hardware Components

Removing an MX80 MIC

MICs are hot-insertable and hot-removable. When you remove a MIC, the router continues
to function, although the MIC interfaces being removed no longer function.

In the modular configuration of the MX80 router, the MICs can be installed in two slots
in the front of the router. A MIC weighs less than 2 lb (0.9 kg).

To remove a MIC (see Figure 34 on page 78 and Figure 35 on page 78):

1. Place an electrostatic bag or antistatic mat on a flat, stable surface to receive the
MIC. If the MIC connects to fiber-optic cable, have ready a rubber safety cap for each
transceiver and cable.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

3. Use one of the following methods to take the MIC offline:

• Press its online/offline button. Use a narrow-ended tool that fits inside the opening
that leads to the button. Press and hold the button until the MIC OK/FAIL LED goes
off (about 5 seconds).

• Issue the following CLI command:

user@host> request chassis mic fpc-slot slot-number mic-slot slot-number
offline

4. Label the cables connected to the MIC so that you can later reconnect each cable
to the correct MIC.

5. Disconnect the cables from the MIC. If the MIC uses fiber-optic cable, immediately
cover each transceiver and the end of each cable with a rubber safety cap.

WARNING: Do not look directly into a fiber-optic transceiver or into the ends of
fiber-optic cables. Fiber-optic transceivers and fiber-optic cable connected to a
transceiver emit laser light that can damage your eyes.

CAUTION: Do not leave a fiber-optic transceiver uncovered except when inserting or

removing cable. The safety cap keeps the port clean and prevents accidental exposure
to laser light.

6. Arrange the cable to prevent it from dislodging or developing stress points. Secure
the cable so that it is not supporting its own weight as it hangs to the floor. Place
excess cable out of the way in a neatly coiled loop.

CAUTION: Avoid bending fiber-optic cable beyond its minimum bend radius. An arc
smaller than a few inches in diameter can damage the cable and cause problems that
are difficult to diagnose.

Copyright © 2010, Juniper Networks, Inc. 77

MX80 3D Universal Edge Router Hardware Guide

7. Pull the ejector lever above the MIC you are removing away from the router. Pulling
the ejector lever disconnects the MIC from the chassis.

NOTE: To remove a dual-wide MIC that takes up both MIC slots, you must pull both
ejector levers.

8. Grasp the handles on the MIC faceplate, and slide the MIC out of the chassis. Place
it in the electrostatic bag or on the antistatic mat.

9. If you are not reinstalling a MIC into the emptied MIC slot within a short time, install
a blank MIC panel over the slot to maintain proper airflow in the chassis card cage.

Figure 34: Removing a MIC

g005030

Figure 35: Removing a Dual-Wide MIC

Ejector levers

g005033

Installing an MX80 MIC

To install a MIC (see Figure 37 on page 80):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

2. If the MIC uses fiber-optic cable, verify that a rubber safety cap is over each transceiver
on the faceplate. Install a cap if necessary.

78 Copyright © 2010, Juniper Networks, Inc.

 Chapter 14: Replacing MX80 Hardware Components

3. If you have used a dual-wide MIC and are now replacing it with two “single” MICs,
install the septum (see Figure 36 on page 79):

a. Align the bottom of the septum with the groves in the center of the two MIC
slots.

b. Slide the septum towards the rear of the chassis until it is seated firmly in place.

Figure 36: Installing the Septum

Septum
(located in the center
of the MIC slots)

g005034
Insert the tabs on the bottom Slide the septum towards the rear of the
of the septum into the groves in chassis until it is seated firmly in place.
the center of the two MIC slots.

4. Pull the ejector lever above the MIC slot away from the router.

5. Align the rear of the MIC with the guides located at the corners of the MIC slot.

6. Slide the MIC into the MIC slot until it is firmly seated in the chassis.

CAUTION: Slide the MIC straight into the slot to avoid damaging the components on
the MIC.

7. Verify that the ejector lever is engaged by pushing it toward the router.

8. If the MIC uses fiber-optic cable, remove the rubber safety cap from each transceiver
and the end of each cable.

WARNING: Do not look directly into a fiber-optic transceiver or into the ends of
fiber-optic cables. Fiber-optic transceivers and fiber-optic cable connected to a
transceiver emit laser light that can damage your eyes.

CAUTION: Do not leave a fiber-optic transceiver uncovered except when inserting or

removing cable. The safety cap keeps the port clean and prevents accidental exposure
to laser light.

9. Insert the appropriate cables into the cable connectors on the MIC.

Copyright © 2010, Juniper Networks, Inc. 79

MX80 3D Universal Edge Router Hardware Guide

10. Arrange each cable to prevent the cable from dislodging or developing stress points.
Secure the cable so that it is not supporting its own weight as it hangs to the floor.
Place excess cable out of the way in a neatly coiled loop.

CAUTION: Do not let fiber-optic cable hang free from the connector. Do not allow
fastened loops of cable to dangle, which stresses the cable at the fastening point.

CAUTION: Avoid bending fiber-optic cable beyond its minimum bend radius. An arc
smaller than a few inches in diameter can damage the cable and cause problems that
are difficult to diagnose.

11. Use one of the following methods to bring the MIC online:

• Press the MIC offline/online button until the MIC OK/FAIL LED lights green.

• Issue the following CLI command:

user@host> request chassis mic fpc-slot slot-number mic-slot slot-number
online

The normal functioning status LED confirms that the MIC is online. You can also
verify correct MIC functioning by issuing the show chassis fpc pic-status command
described in “Maintaining the MX80 MICs” on page 63.

Figure 37: Installing a MIC g005029

Installing an MX80 Dual-Wide MIC

To install a dual-wide MIC (see Figure 39 on page 82):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

2. If the MIC uses fiber-optic cable, verify that a rubber safety cap is over each transceiver
on the faceplate. Install a cap if necessary.

80 Copyright © 2010, Juniper Networks, Inc.

 Chapter 14: Replacing MX80 Hardware Components

3. Remove the septum, if necessary (see Figure 38 on page 81):

a. Lift the latch in the center of the two MIC slots to disengage the septum from
the chassis.

b. Slide the septum towards you, and then lift the septum out of the slot.

c. Store the septum for later use.

Figure 38: Removing the Septum

Septum

g005031
Lift up here. Then slide the Lift the septum out of the chassis.
septum towards you.

4. Pull the ejector lever above both MIC slots away from the router.

5. Align the rear of the MIC with the guides located at the corners of the MIC slot.

6. Slide the MIC into the MIC slot until it is firmly seated in the chassis.

CAUTION: Slide the MIC straight into the slot to avoid damaging the components on
the MIC.

7. Verify that the ejector levers are engaged by pushing them toward the router.

8. If the MIC uses fiber-optic cable, remove the rubber safety cap from each transceiver
and the end of each cable.

WARNING: Do not look directly into a fiber-optic transceiver or into the ends of
fiber-optic cables. Fiber-optic transceivers and fiber-optic cable connected to a
transceiver emit laser light that can damage your eyes.

CAUTION: Do not leave a fiber-optic transceiver uncovered except when inserting or

removing cable. The safety cap keeps the port clean and prevents accidental exposure
to laser light.

9. Insert the appropriate cables into the cable connectors on the MIC.

Copyright © 2010, Juniper Networks, Inc. 81

MX80 3D Universal Edge Router Hardware Guide

10. Arrange each cable to prevent the cable from dislodging or developing stress points.
Secure the cable so that it is not supporting its own weight as it hangs to the floor.
Place excess cable out of the way in a neatly coiled loop.

CAUTION: Do not let fiber-optic cable hang free from the connector. Do not allow
fastened loops of cable to dangle, which stresses the cable at the fastening point.

CAUTION: Avoid bending fiber-optic cable beyond its minimum bend radius. An arc
smaller than a few inches in diameter can damage the cable and cause problems that
are difficult to diagnose.

11. Use one of the following methods to bring the MIC online:

• Press the MIC offline/online button until the MIC OK/FAIL LED lights green.

• Issue the following CLI command:

user@host> request chassis mic fpc-slot slot-number mic-slot slot-number
online

The normal functioning status LED confirms that the MIC is online. You can also
verify correct MIC functioning by issuing the show chassis fpc pic-status command
described in “Maintaining the MX80 MICs” on page 63.

Figure 39: Installing a Dual-Wide MIC

g005032

Related Topics • MX80 Modular Interface Card Description on page 13

• Maintaining the MX80 MICs on page 63

• Troubleshooting the MX80 MICs on page 70

• Preventing Electrostatic Discharge Damage to an MX80 Router on page 104

• MX80 MIC Serial Number Label on page 162

• request chassis mic

• show chassis fpc

82 Copyright © 2010, Juniper Networks, Inc.

 Chapter 14: Replacing MX80 Hardware Components

Replacing a Cable on an MX80 MIC

• Removing a Cable on an MX80 MIC on page 83

• Installing a Cable on an MX80 MIC on page 83

Removing a Cable on an MX80 MIC

Removing and installing cables on a MIC does not affect router function, except that the
component does not receive or transmit data while its cable is disconnected.

To remove a fiber-optic cable:

1. If the component connects to fiber-optic cable, have ready a rubber safety cap for
each cable and transceiver.

2. If removing all cables connected to the component, use one of the following methods
to take the MIC offline:

• Press and hold the MIC offline/online button until the MIC LED goes off (about 5
seconds).

• Issue the following CLI command:

user@host> request chassis mic fpc-slot slot-number mic-slot slot-number
offline

3. Unplug the cable from the cable connector port. If the MIC uses fiber-optic cable,
immediately cover each transceiver and the end of each cable with a rubber safety
cap.

WARNING: Do not look directly into a fiber-optic transceiver or into the ends of
fiber-optic cables. Fiber-optic transceivers and fiber-optic cable connected to a
transceiver emit laser light that can damage your eyes.

CAUTION: Do not leave a fiber-optic transceiver uncovered except when inserting or

removing cable. The safety cap keeps the port clean and prevents accidental exposure
to laser light.

4. Remove the cable from the cable management bracket and detach it from the
destination port.

Installing a Cable on an MX80 MIC

To install a cable:

1. Have ready a length of the type of cable used by the component. For cable
specifications, see the MX Series 3D Universal Edge Routers Line Card Guide.

2. If the cable connector port is covered by a rubber safety cap, remove the cap.

Copyright © 2010, Juniper Networks, Inc. 83

MX80 3D Universal Edge Router Hardware Guide

WARNING: Do not look directly into a fiber-optic transceiver or into the ends of
fiber-optic cables. Fiber-optic transceivers and fiber-optic cable connected to a
transceiver emit laser light that can damage your eyes.

CAUTION: Do not leave a fiber-optic transceiver uncovered except when inserting or

removing cable. The safety cap keeps the port clean and prevents accidental exposure
to laser light.

3. Insert the cable connector into the cable connector port on the MIC faceplate.

4. Arrange the cable in the cable management bracket to prevent it from dislodging or
developing stress points. Secure the cable so that it is not supporting its own weight
as it hangs to the floor. Place excess cable out of the way in a neatly coiled loop.
Placing fasteners on the loop helps to maintain its shape.

CAUTION: Avoid bending fiber-optic cable beyond its minimum bend radius. An arc
smaller than a few inches in diameter can damage the cable and cause problems that
are difficult to diagnose.

CAUTION: Do not let fiber-optic cable hang free from the connector. Do not allow
fastened loops of cable to dangle, which stresses the cable at the fastening point.

5. Insert the other end of the cable into the destination port.

6. Repeat the previous steps for any additional cables.

7. If the MIC is offline (its failure indicator LED is lit), use one of the following methods
to bring it online:

• Press the MIC offline/online button until the MIC LED lights green.

• Issue the following CLI command:

user@host>request chassis mic fpc-slot slot-number mic-slot slot-number
online

The normal functioning indicator LED confirms that the component is online. You
can also verify correct MIC functioning by issuing the show chassis fpc pic-status
command.

Related Topics • MX80 Modular Interface Card Description on page 13

• Maintaining Cables That Connect to MX80 MICs on page 64

• Replacing an MX80 MIC on page 76

• Replacing an MX80 SFP or XFP Transceiver on page 94

• Preventing Electrostatic Discharge Damage to an MX80 Router on page 104

84 Copyright © 2010, Juniper Networks, Inc.

 Chapter 14: Replacing MX80 Hardware Components

• request chassis mic

• show chassis fpc

Replacing an MX80 AC Power Supply

• Removing an MX80 AC Power Supply on page 85

• Installing an MX80 AC Power Supply on page 86

Removing an MX80 AC Power Supply

Before you remove a power supply, be aware of the following:

NOTE: The minimum number of power supplies must be present in the router at all
times.

CAUTION: To maintain proper cooling and prevent thermal shutdown of the operating
power supply unit, each power supply slot must contain either a power supply or a blank
panel. If you remove a power supply, you must install a replacement power supply or
a blank panel shortly after the removal.

NOTE: After powering off a power supply, wait at least 60 seconds before turning it
back on.

To remove an AC power supply (see Figure 40 on page 86):

1. Switch off the dedicated customer site circuit breaker for the power supply, and
remove the power cord from the AC power source. Follow the instructions for your
site.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

3. Move the AC input switch next to the appliance inlet on the power supply to the
off (O) position.

4. Remove the power cord from the power supply.

5. Press the release latch on the left side of the power supply to disconnect the power
supply from the chassis.

6. Pull the power supply straight out of the chassis.

Copyright © 2010, Juniper Networks, Inc. 85

MX80 3D Universal Edge Router Hardware Guide

Figure 40: Removing an AC Power Supply

g005004
Installing an MX80 AC Power Supply
To install an AC power supply (see Figure 41 on page 87):

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

2. Move the AC input switch next to the appliance inlet on the power supply to the
off (O) position.

3. Using both hands, slide the power supply straight into the chassis until the power
supply is fully seated in the chassis slot. The power supply faceplate should be flush
with any adjacent power supply faceplate or blank installed in the power supply slot.

4. Attach the power cord to the power supply.

5. Attach the power cord to the AC power source, and switch on the dedicated customer
site circuit breaker. Follow the instructions for your site.

6. Move the AC input switch next to the appliance inlet on the power supply to the on
( | ) position and observe the status LED on the power supply faceplate. If the power
supply is correctly installed and functioning normally, the status LED lights green
steadily.

86 Copyright © 2010, Juniper Networks, Inc.

 Chapter 14: Replacing MX80 Hardware Components

Figure 41: Installing an AC Power Supply

g005003
Related Topics • MX80 Power System Description on page 16

• MX80 Router AC Power Specifications on page 141

• AC Power Circuit Breaker Requirements for the MX80 Router on page 143

• AC Power Cord Specifications for the MX80 Router on page 143

• Preventing Electrostatic Discharge Damage to an MX80 Router on page 104

Replacing an MX80 AC Power Supply Cord

• Disconnecting an MX80 AC Power Supply Cord on page 87

• Connecting an MX80 AC Power Supply Cord on page 88

Disconnecting an MX80 AC Power Supply Cord

To disconnect the AC power cord:

1. Switch off the dedicated customer site circuit breaker for the power supply, and
remove the power cord from the AC power source. Follow the instructions for your
site.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

3. Move the AC input switch next to the appliance inlet on the power supply to the
off (O) position.

4. Remove the power cord from the power supply.

Copyright © 2010, Juniper Networks, Inc. 87

MX80 3D Universal Edge Router Hardware Guide

Connecting an MX80 AC Power Supply Cord

To connect the AC power cord:

1. Locate a replacement power cord with the type of plug appropriate for your
geographical location (see “AC Power Cord Specifications for the MX80 Router” on
page 143).

2. Connect the power cord to the power supply.

3. Insert the power cord plug into an external AC power source receptacle.

4. Route the power cord appropriately. Verify that the power cord does not block the
air exhaust and access to router components, or drape where people could trip on
it.

5. Switch the AC input switch on the each power supply to the on ( | ) position and
observe the status LED on the power supply faceplate. If the power supply is correctly
installed and functioning normally, the status LED lights green steadily.

Replacing an MX80 DC Power Supply

• Removing an MX80 DC Power Supply on page 88

• Installing an MX80 DC Power Supply on page 90

Removing an MX80 DC Power Supply

Before you remove a power supply, be aware of the following:

NOTE: The minimum number of power supplies must be present in the router at all
times.

WARNING: Before performing DC power procedures, ensure that power is removed

from the DC circuit. To ensure that all power is off, locate the circuit breaker on the
panel board that services the DC circuit, switch the circuit breaker to the off position,
and tape the switch handle of the circuit breaker in the off position.

CAUTION: To maintain proper cooling and prevent thermal shutdown of the operating
power supply unit, each power supply slot must contain either a power supply or a blank
panel. If you remove a power supply, you must install a replacement power supply or
a blank panel shortly after the removal.

NOTE: After powering off a power supply, wait at least 60 seconds before turning it
back on.

88 Copyright © 2010, Juniper Networks, Inc.

 Chapter 14: Replacing MX80 Hardware Components

To remove a DC power supply (see Figure 42 on page 89):

1. Switch off the dedicated customer site circuit breaker for the power supply being
removed. Follow your site's procedures for ESD.

2. Make sure that the voltage across the DC power source cable leads is 0 V and that
there is no chance that the cables might become active during the removal process.

3. Verify that the status LED on the power supply is not lit.

4. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

5. Move the DC circuit breaker on the DC power supply faceplate to the off (O) position.

6. Remove the clear plastic cover protecting the terminal studs on the faceplate (see
Figure 43 on page 90).

7. Remove the screw from each of the terminals. (Use a number 2 Phillips screwdriver.)

8. Remove the cable lugs from the terminals.

9. Carefully move the power cables out of the way.

10. Press the latch located on the left side of the power supply, to release it from the
chassis.

11. Pull the power supply straight out of the chassis.

Figure 42: Removing a DC Power Supply g005007

Copyright © 2010, Juniper Networks, Inc. 89

MX80 3D Universal Edge Router Hardware Guide

Figure 43: Disconnecting the DC Power Cables

g005006
Installing an MX80 DC Power Supply

WARNING: Before performing DC power procedures, ensure that power is removed

from the DC circuit. To ensure that all power is off, locate the circuit breaker on the
panel board that services the DC circuit, switch the circuit breaker to the off position,
and tape the switch handle of the circuit breaker in the off position.

To install a DC power supply (see Figure 44 on page 91):

1. Ensure that the voltage across the DC power source cable leads is 0 V and that there
is no chance that the cable leads might become active during installation.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

3. Switch the DC circuit breaker on the DC power supply faceplate to the off (O) position.

4. Using both hands, slide the power supply straight into the chassis until the power
supply is fully seated in the chassis slot. The power supply faceplate should be flush
with any adjacent power supply faceplate or blank installed in the power supply slot.

5. Remove the clear plastic cover protecting the terminal on the faceplate.

6. Remove the screws from the terminals.

7. Secure each power cable lug to the terminal with the screw (see Figure 45 on
page 92). Apply between 5 lb-in. (0.6 Nm) and 6 lb-in. (0.7 Nm) of torque to screw.
Do not overtighten the nut. (Use a number 2 Phillips screwdriver.)

a. Secure the positive (+) DC source power cable lug to the RTN (return) terminal.

b. Secure the negative (–) DC source power cable lug to the –48V (input) terminal.

CAUTION: Ensure that each power cable lug seats flush against the surface of the
terminal block as you are tightening the screws. Ensure that each screw is properly
threaded into the terminal. Applying installation torque to the screw when improperly
threaded may result in damage to the terminal.

90 Copyright © 2010, Juniper Networks, Inc.

 Chapter 14: Replacing MX80 Hardware Components

CAUTION: You must ensure that power connections maintain the proper polarity. The
power source cables might be labeled (+) and (–) to indicate their polarity. There is no
standard color coding for DC power cables. The color coding used by the external DC
power source at your site determines the color coding for the leads on the power cables
that attach to the terminal studs on each power supply.

NOTE: For information about connecting to DC power sources, see “MX80 Router DC
Power Specifications” on page 146.

8. Replace the clear plastic cover over the terminals on the faceplate.

9. Verify that the power cabling is correct, that the cables are not touching or blocking
access to router components, and that they do not drape where people could trip
on them.

10. On each of the DC power supplies, switch the DC circuit breaker to the center position
before moving it to the on ( | ) position.

NOTE: The circuit breaker may bounce back to the off (O) position if you move the
breaker too quickly.

NOTE: If more than one power supply is being installed, turn on all power supplies at
the same time.

Figure 44: Installing a DC Power Supply

g005005

Copyright © 2010, Juniper Networks, Inc. 91

MX80 3D Universal Edge Router Hardware Guide

Figure 45: Connecting the DC Power Cables

g005006
Related Topics • MX80 Power System Description on page 16

• Preventing Electrostatic Discharge Damage to an MX80 Router on page 104

• MX80 Router DC Power Specifications on page 146

• DC Power Circuit Breaker Requirements for the MX80 Router on page 148

• DC Power Source Cabling for the MX80 Router on page 149

• DC Power Cable Specifications for the MX80 Router on page 149

Replacing an MX80 DC Power Supply Cable

• Disconnecting an MX80 DC Power Supply Cable on page 92

• Connecting an MX80 DC Power Supply Cable on page 93

Disconnecting an MX80 DC Power Supply Cable

WARNING: Before performing DC power procedures, ensure that power is removed

from the DC circuit. To ensure that all power is off, locate the circuit breaker on the
panel board that services the DC circuit, switch the circuit breaker to the off position,
and tape the switch handle of the circuit breaker in the off position.

To disconnect a power cable for a DC power supply:

1. Switch off the dedicated customer site circuit breaker for the power supply being
removed. Follow your site's procedures for ESD.

2. Make sure that the voltage across the DC power source cable leads is 0 V and that
there is no chance that the cables might become active during the removal process.

3. Verify that the status LED on the power supply is not lit.

4. Remove the power cable from the external DC power source.

5. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

6. Move the DC circuit breaker on the DC power supply faceplate to the off (O) position.

7. Remove the clear plastic cover protecting the terminal studs on the faceplate.

92 Copyright © 2010, Juniper Networks, Inc.

 Chapter 14: Replacing MX80 Hardware Components

8. Remove the screw from each of the terminals. (Use a number 2 Phillips screwdriver.)

9. Remove the cable lugs from the terminals.

10. Carefully move the power cables out of the way.

Connecting an MX80 DC Power Supply Cable

WARNING: Before performing DC power procedures, ensure that power is removed

from the DC circuit. To ensure that all power is off, locate the circuit breaker on the
panel board that services the DC circuit, switch the circuit breaker to the off position,
and tape the switch handle of the circuit breaker in the off position.

To connect a power cable for a DC power supply:

1. Locate a replacement power cable that meets the specifications.

2. Verify that a licensed electrician has attached a cable lug to the replacement power
cable.

3. Verify that the status LED is off.

4. Secure each power cable lug to the terminal with the screw (see Figure 46 on
page 94). Apply between 5 lb-in. (0.6 Nm) and 6 lb-in. (0.7 Nm) of torque to screw.
Do not overtighten the nut. (Use a number 2 Phillips screwdriver.)

CAUTION: Ensure that each power cable lug seats flush against the surface of the
terminal block as you are tightening the screws. Ensure that each screw is properly
threaded into the terminal. Applying installation torque to the screw when improperly
threaded may result in damage to the terminal.

CAUTION: The maximum torque rating of the terminal screws on the DC power supply
is 6 lb-in. (0.7 Nm). The terminal screws may be damaged if excessive torque is applied.
Use only a torque-controlled driver to tighten screws on the DC power supply terminals.
Use an appropriately-sized driver, with a maximum torque capacity of 6 lb-in. or less.
Ensure that the driver is undamaged and properly calibrated and that you have been
trained in its use. You may wish to use a driver that is designed to prevent overtorque
when the preset torque level is achieved.

Copyright © 2010, Juniper Networks, Inc. 93

MX80 3D Universal Edge Router Hardware Guide

Figure 46: Connecting Power Cables to the DC Power Supply

g005006
5. Verify that the DC power cable is connected correctly, that it does not touch or block
access to router components, and that it does not drape where people could trip on
it.

6. Replace the clear plastic cover over the terminals on the faceplate.

7. Attach the power cable to the DC power source.

8. Turn on the dedicated customer site circuit breaker to the power supply.

9. Verify that the status LED on the power supply is lit green steadily.

10. On each of the DC power supplies, switch the DC circuit breaker to the center position
before moving it to the on ( | ) position.

NOTE: The circuit breaker may bounce back to the off (O) position if you move the
breaker too quickly.

Observe the status LED on the power supply faceplate. If the power supply is correctly
installed and functioning normally, the status LED lights green steadily.

Replacing an MX80 SFP or XFP Transceiver

Small form-factor pluggable transceivers (SFPs) and 10-gigabit small form-factor

pluggables (XFPs) are optical transceivers that are installed in a MIC. SFPs and XFPs are
hot-insertable and hot-removable.

• Removing an MX80 SFP or XFP Transceiver on page 94

• Installing an MX80 SFP or XFP Transceiver on page 96

Removing an MX80 SFP or XFP Transceiver

Removing an SFP or XFP does not interrupt MIC functioning, but the removed SFP or XFP
no longer receives or transmits data.

94 Copyright © 2010, Juniper Networks, Inc.

 Chapter 14: Replacing MX80 Hardware Components

To remove an SFP or XFP transceiver (see Figure 47 on page 95):

1. Have ready a replacement transceiver or a transceiver slot plug, an antistatic mat,

and a rubber safety cap for the transceiver.

2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

3. Label the cables connected to the transceiver so that you can reconnect them
correctly later.

WARNING: Do not look directly into a fiber-optic transceiver or into the ends of
fiber-optic cables. Fiber-optic transceivers and fiber-optic cable connected to a
transceiver emit laser light that can damage your eyes.

4. Remove the cable connector from the transceiver.

5. Pull the ejector handle out from the transceiver to unlock the transceiver.

CAUTION: Make sure that you open the ejector handle completely until you hear it click.
This prevents damage to the transceiver.

Use needlenose pliers to pull the ejector handle out from the transceiver.

6. Grasp the transceiver ejector handle, and pull the transceiver approximately 0.5 in. (1.3
cm) out of the MIC.

7. Using your fingers, grasp the body of the transceiver, and pull it the rest of the way
out of the MIC.

Figure 47: Removing SFPs or XFPs

8. Place a rubber safety cap over the transceiver.

9. Place the removed transceiver on an antistatic mat or in an electrostatic bag.

Copyright © 2010, Juniper Networks, Inc. 95

MX80 3D Universal Edge Router Hardware Guide

CAUTION: After removing a transceiver from the chassis, wait at least 30 seconds
before reinserting it or inserting a transceiver into a different slot.

Installing an MX80 SFP or XFP Transceiver

To install an SFP or XFP:

1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

2. Take each transceiver to be installed out of its electrostatic bag, and identify the
slot on the component where it will be installed.

3. Verify that each transceiver is covered by a rubber safety cap. If it is not, cover the
transceiver with a safety cap.

4. Carefully align the transceiver with the slots in the component. The connectors
should face the component.

5. Slide the transceiver until the connector is seated in the component slot. If you are
unable to fully insert the transceiver, make sure the connector is facing the right way.

6. Close the ejector handle of the transceiver.

7. Remove the rubber safety cap from the transceiver and the end of the cable. Insert
the cable into the transceiver.

WARNING: Do not look directly into a fiber-optic transceiver or into the ends of
fiber-optic cables. Fiber-optic transceivers and fiber-optic cable connected to a
transceiver emit laser light that can damage your eyes.

8. Verify that the status LEDs on the component faceplate indicate that the SFP or
XFP is functioning correctly. For more information about the component LEDs, see
the MX Series 3D Universal Edge Routers Line Card Guide.

Related Topics • MX80 Modular Interface Card Description on page 13

• Replacing a Cable on an MX80 MIC on page 83

• Preventing Electrostatic Discharge Damage to an MX80 Router on page 104

96 Copyright © 2010, Juniper Networks, Inc.

PART 4

Appendixes
• Safety and Regulatory Compliance Information for the MX80 Router on page 99
• MX80 Router Physical Specifications on page 135
• MX80 Router Environmental Specifications on page 137
• Power Guidelines, Requirements, and Specifications for the MX80 Router on page 139
• Cable and Wire Guidelines and Specifications for the MX80 Router on page 153
• MX80 Cable Connector Pinouts on page 157
• Contacting Customer Support and Returning MX80 Hardware on page 159

Copyright © 2010, Juniper Networks, Inc. 97

MX80 3D Universal Edge Router Hardware Guide

98 Copyright © 2010, Juniper Networks, Inc.

APPENDIX A

Safety and Regulatory Compliance

Information for the MX80 Router

• Definition of Safety Warning Levels on page 99

• Safety Guidelines and Warnings for the MX80 Router on page 101
• Agency Approvals and Compliance Statements for the MX80 Router on page 129

Definition of Safety Warning Levels

The M Series, MX Series, and T Series router documentation uses the following levels of
safety warnings:

NOTE: You might find this information helpful in a particular situation, or might otherwise
overlook it.

CAUTION: You must observe the specified guidelines to avoid minor injury or discomfort
to you, or severe damage to the router.

WARNING: This symbol alerts you to the risk of personal injury from a laser.

WARNING: This symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.
Waarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie
die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient
u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen.

Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa
ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää

Copyright © 2010, Juniper Networks, Inc. 99

MX80 3D Universal Edge Router Hardware Guide

sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien

ehkäisykeinoista.

Attention Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une
situation pouvant causer des blessures ou des dommages corporels. Avant de travailler
sur un équipement, soyez conscient des dangers posés par les circuits électriques et
familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents.

Warnung Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die
zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät
beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und
der Standardpraktiken zur Vermeidung von Unfällen bewußt.

Avvertenza Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe

causare infortuni alle persone. Prima di lavorare su qualsiasi apparecchiatura, occorre
conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratiche standard
per la prevenzione di incidenti.

Advarsel Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre
til personskade. Før du utfører arbeid på utstyr, må du vare oppmerksom på de
faremomentene som elektriske kretser innebærer, samt gjøre deg kjent med vanlig
praksis når det gjelder å unngå ulykker.

Aviso Este símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá
causar danos físicos. Antes de começar a trabalhar com qualquer equipamento,
familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer
práticas comuns que possam prevenir possíveis acidentes.

¡Atención! Este símbolo de aviso significa peligro. Existe riesgo para su integridad física.
Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente
eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes.

Varning! Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan
leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten
om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador.

Related Topics • General Safety Warnings for M Series, MX Series, and T Series Routers on page 102

• Installation Safety Warnings for M Series, MX Series, and T Series Routers on page 107

• Maintenance and Operational Safety Warnings for M Series, MX Series, and T Series
Routers on page 115

• General Electrical Safety Warnings for M Series, MX Series, and T Series Routers on
page 120

• DC Power Electrical Safety Warnings for M Series, MX Series, and T Series Routers on
page 126

100 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

Safety Guidelines and Warnings for the MX80 Router

• General Safety Guidelines for M Series, MX Series, and T Series Routers on page 101
• General Safety Warnings for M Series, MX Series, and T Series Routers on page 102
• Preventing Electrostatic Discharge Damage to an MX80 Router on page 104
• Fire Safety Requirements for M Series, MX Series, and T Series Routers on page 105
• Installation Safety Warnings for M Series, MX Series, and T Series Routers on page 107
• MX80 Chassis Lifting Guidelines on page 111
• General Laser Safety Guidelines for M Series, MX Series, and T Series Routers on page 112
• Laser Safety Warnings for M Series, MX Series, and T Series Routers on page 112
• Maintenance and Operational Safety Warnings for M Series, MX Series, and T Series
Routers on page 115
• General Electrical Safety Guidelines and Warnings for the MX80 Router on page 120

General Safety Guidelines for M Series, MX Series, and T Series Routers

The following guidelines help ensure your safety and protect the router from damage.
The list of guidelines might not address all potentially hazardous situations in your working
environment, so be alert and exercise good judgment at all times.

• Perform only the procedures explicitly described in this documentation. Make sure that
only authorized service personnel perform other system services.

• Keep the area around the chassis clear and free from dust before, during, and after
installation.

• Keep tools away from areas where people could trip over them while walking.

• Do not wear loose clothing or jewelry, such as rings, bracelets, or chains, which could
become caught in the chassis.

• Wear safety glasses if you are working under any conditions that could be hazardous
to your eyes.

• Do not perform any actions that create a potential hazard to people or make the
equipment unsafe.

• Never attempt to lift an object that is too heavy for one person to handle.

• Never install or manipulate wiring during electrical storms.

• Never install electrical jacks in wet locations unless the jacks are specifically designed
for wet environments.

• Operate the router only when it is properly grounded.

• Do not open or remove chassis covers or sheet metal parts unless instructions are
provided in this documentation. Such an action could cause severe electrical shock.

• Do not push or force any objects through any opening in the chassis frame. Such an
action could result in electrical shock or fire.

Copyright © 2010, Juniper Networks, Inc. 101

MX80 3D Universal Edge Router Hardware Guide

• Avoid spilling liquid onto the chassis or onto any router component. Such an action
could cause electrical shock or damage the router.

• Avoid touching uninsulated electrical wires or terminals that have not been
disconnected from their power source. Such an action could cause electrical shock.

Related Topics • General Safety Warnings for M Series, MX Series, and T Series Routers on page 102

General Safety Warnings for M Series, MX Series, and T Series Routers

• Qualified Personnel Warning on page 102
• Restricted Access Area Warning on page 102

Qualified Personnel Warning

WARNING: Only trained and qualified personnel should install or replace the router.
Waarschuwing Installatie en reparaties mogen uitsluitend door getraind en bevoegd
personeel uitgevoerd worden.

Varoitus Ainoastaan koulutettu ja pätevä henkilökunta saa asentaa tai vaihtaa tämän
laitteen.

Attention Tout installation ou remplacement de l'appareil doit être réalisé par du

personnel qualifié et compétent.

Warnung Gerät nur von geschultem, qualifiziertem Personal installieren oder

auswechseln lassen.

Avvertenza Solo personale addestrato e qualificato deve essere autorizzato ad installare

o sostituire questo apparecchio.

Advarsel Kun kvalifisert personell med riktig opplæring bør montere eller bytte ut dette
utstyret.

Aviso Este equipamento deverá ser instalado ou substituído apenas por pessoal
devidamente treinado e qualificado.

¡Atención! Estos equipos deben ser instalados y reemplazados exclusivamente por

personal técnico adecuadamente preparado y capacitado.

Varning! Denna utrustning ska endast installeras och bytas ut av utbildad och
kvalificerad personal.

Restricted Access Area Warning

WARNING: The router is intended for installation in restricted access areas. A restricted
access area is an area to which access can be gained only by service personnel through

102 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

the use of a special tool, lock and key, or other means of security, and which is controlled
by the authority responsible for the location.
Waarschuwing Dit toestel is bedoeld voor installatie op plaatsen met beperkte toegang.
Een plaats met beperkte toegang is een plaats waar toegang slechts door
servicepersoneel verkregen kan worden door middel van een speciaal instrument, een
slot en sleutel, of een ander veiligheidsmiddel, en welke beheerd wordt door de
overheidsinstantie die verantwoordelijk is voor de locatie.

Varoitus Tämä laite on tarkoitettu asennettavaksi paikkaan, johon pääsy on rajoitettua.

Paikka, johon pääsy on rajoitettua, tarkoittaa paikkaa, johon vain huoltohenkilöstö
pääsee jonkin erikoistyökalun, lukkoon sopivan avaimen tai jonkin muun turvalaitteen
avulla ja joka on paikasta vastuussa olevien toimivaltaisten henkilöiden valvoma.

Attention Cet appareil est à installer dans des zones d'accès réservé. Ces dernières
sont des zones auxquelles seul le personnel de service peut accéder en utilisant un outil
spécial, un mécanisme de verrouillage et une clé, ou tout autre moyen de sécurité.
L'accès aux zones de sécurité est sous le contrôle de l'autorité responsable de
l'emplacement.

Warnung Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt
vorgesehen. Ein Bereich mit beschränktem Zutritt ist ein Bereich, zu dem nur
Wartungspersonal mit einem Spezialwerkzeugs, Schloß und Schlüssel oder anderer
Sicherheitsvorkehrungen Zugang hat, und der von dem für die Anlage zuständigen
Gremium kontrolliert wird.

Avvertenza Questa unità deve essere installata in un'area ad accesso limitato. Un'area
ad accesso limitato è un'area accessibile solo a personale di assistenza tramite
un'attrezzo speciale, lucchetto, o altri dispositivi di sicurezza, ed è controllata
dall'autorità responsabile della zona.

Advarsel Denne enheten er laget for installasjon i områder med begrenset adgang. Et
område med begrenset adgang gir kun adgang til servicepersonale som bruker et spesielt
verktøy, lås og nøkkel, eller en annen sikkerhetsanordning, og det kontrolleres av den
autoriteten som er ansvarlig for området.

Aviso Esta unidade foi concebida para instalação em áreas de acesso restrito. Uma
área de acesso restrito é uma área à qual apenas tem acesso o pessoal de serviço
autorizado, que possua uma ferramenta, chave e fechadura especial, ou qualquer outra
forma de segurança. Esta área é controlada pela autoridade responsável pelo local.

¡Atención! Esta unidad ha sido diseñada para instalarse en áreas de acceso restringido.
Área de acceso restringido significa un área a la que solamente tiene acceso el personal
de servicio mediante la utilización de una herramienta especial, cerradura con llave, o
algún otro medio de seguridad, y que está bajo el control de la autoridad responsable
del local.

Varning! Denna enhet är avsedd för installation i områden med begränsat tillträde. Ett
område med begränsat tillträde får endast tillträdas av servicepersonal med ett speciellt

Copyright © 2010, Juniper Networks, Inc. 103

MX80 3D Universal Edge Router Hardware Guide

verktyg, lås och nyckel, eller annan säkerhetsanordning, och kontrolleras av den
auktoritet som ansvarar för området.

Related Topics • Installation Safety Warnings for M Series, MX Series, and T Series Routers on page 107

• Maintenance and Operational Safety Warnings for M Series, MX Series, and T Series
Routers on page 115

• General Electrical Safety Warnings for M Series, MX Series, and T Series Routers on
page 120

• DC Power Electrical Safety Warnings for M Series, MX Series, and T Series Routers on
page 126

Preventing Electrostatic Discharge Damage to an MX80 Router

Many router hardware components are sensitive to damage from static electricity. Some
components can be impaired by voltages as low as 30 V. You can easily generate
potentially damaging static voltages whenever you handle plastic or foam packing
material or if you move components across plastic or carpets. Observe the following
guidelines to minimize the potential for electrostatic discharge (ESD) damage, which
can cause intermittent or complete component failures:

• Always use an ESD wrist strap or ankle strap, and make sure that it is in direct contact
with your skin.

CAUTION: For safety, periodically check the resistance value of the ESD strap. The
measurement should be in the range of from 1 to 10 Mohms.

• When handling any component that is removed from the chassis, make sure the
equipment end of your ESD strap is attached to one of the electrostatic discharge
points on the chassis (see Figure 48 on page 105).

• Avoid contact between the component and your clothing. ESD voltages emitted from
clothing can still damage components.

• When removing or installing a component, always place it component-side up on an

antistatic surface, in an antistatic card rack, or in an electrostatic bag (see Figure 49
on page 105). If you are returning a component, place it in an electrostatic bag before
packing it.

104 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

Figure 48: ESD Points on the MX80 Chassis

ESD
point
ESD (rear panel)
point
(front panel)

g005010
Figure 49: Placing a Component into an Electrostatic Bag

Related Topics • Grounding the MX80 Router on page 46

• MX80 Router Grounding Specifications on page 139

Fire Safety Requirements for M Series, MX Series, and T Series Routers

• General Fire Safety Requirements on page 105
• Fire Suppression on page 106
• Fire Suppression Equipment on page 106

General Fire Safety Requirements

In the event of a fire emergency involving routers and other network equipment, the safety
of people is the primary concern. Establish procedures for protecting people in the event
of a fire emergency, provide safety training, and properly provision fire-control equipment
and fire extinguishers.

In addition, establish procedures to protect your equipment in the event of a fire

emergency. Juniper Networks products should be installed in an environment suitable
for electronic equipment. We recommend that fire suppression equipment be available

Copyright © 2010, Juniper Networks, Inc. 105

MX80 3D Universal Edge Router Hardware Guide

in the event of a fire in the vicinity of the equipment, and that all local fire, safety, and
electrical codes and ordinances be observed when installing and operating your
equipment.

Fire Suppression
In the event of an electrical hazard or an electrical fire, first turn power off to the equipment
at the source. Then use a Type C fire extinguisher, which uses noncorrosive fire retardants,
to extinguish the fire. For more information about fire extinguishers, see “Fire Suppression
Equipment” on page 106.

Fire Suppression Equipment

Type C fire extinguishers, which use noncorrosive fire retardants such as carbon dioxide
(CO ) and Halotron, are most effective for suppressing electrical fires. Type C fire
2

extinguishers displace the oxygen from the point of combustion to eliminate the fire. For
extinguishing fire on or around equipment that draws air from the environment for cooling,
use this type of inert oxygen displacement extinguisher instead of an extinguisher that
leave residues on equipment.

Do not use multipurpose Type ABC chemical fire extinguishers (dry chemical fire
extinguishers) near Juniper Networks equipment. The primary ingredient in these fire
extinguishers is monoammonium phosphate, which is very sticky and difficult to clean.
In addition, in minute amounts of moisture, monoammonium phosphate can become
highly corrosive and corrodes most metals.

Any equipment in a room in which a chemical fire extinguisher has been discharged is
subject to premature failure and unreliable operation. The equipment is considered to
be irreparably damaged.

NOTE: To keep warranties effective, do not use a dry chemical fire extinguisher to
control a fire at or near a Juniper Networks router. If a dry chemical fire extinguisher is
used, the unit is no longer eligible for coverage under a service agreement.

We recommend that you dispose of any irreparably damaged equipment in an

environmentally responsible manner.

Related Topics • General Safety Guidelines for M Series, MX Series, and T Series Routers on page 101

• General Safety Warnings for M Series, MX Series, and T Series Routers on page 102

• General Electrical Safety Warnings for M Series, MX Series, and T Series Routers on
page 120

• DC Power Electrical Safety Warnings for M Series, MX Series, and T Series Routers on
page 126

106 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

Installation Safety Warnings for M Series, MX Series, and T Series Routers

Observe the following warnings before and during router installation:

• Installation Instructions Warning on page 107

• Rack-Mounting Requirements and Warnings on page 107
• Ramp Warning on page 111

Installation Instructions Warning

WARNING: Read the installation instructions before you connect the router to a power
source.
Waarschuwing Raadpleeg de installatie-aanwijzingen voordat u het systeem met de
voeding verbindt.

Varoitus Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.

Attention Avant de brancher le système sur la source d'alimentation, consulter les

directives d'installation.

Warnung Lesen Sie die Installationsanweisungen, bevor Sie das System an die
Stromquelle anschließen.

Avvertenza Consultare le istruzioni di installazione prima di collegare il sistema

all'alimentatore.

Advarsel Les installasjonsinstruksjonene før systemet kobles til strømkilden.

Aviso Leia as instruções de instalação antes de ligar o sistema à sua fonte de energia.

¡Atención! Ver las instrucciones de instalación antes de conectar el sistema a la red de

alimentación.

Varning! Läs installationsanvisningarna innan du kopplar systemet till dess

strömförsörjningsenhet.

Rack-Mounting Requirements and Warnings

Ensure that the equipment rack into which the router is installed is evenly and securely
supported, to avoid the hazardous condition that could result from uneven mechanical
loading.

WARNING: To prevent bodily injury when mounting or servicing the router in a rack,
take the following precautions to ensure that the system remains stable. The following
directives help maintain your safety:

Copyright © 2010, Juniper Networks, Inc. 107

MX80 3D Universal Edge Router Hardware Guide

• The router must be installed into a rack that is secured to the building structure.

• The router should be mounted at the bottom of the rack if it is the only unit in the
rack.

• When mounting the router in a partially filled rack, load the rack from the bottom to
the top with the heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before mounting
or servicing the router in the rack.

Waarschuwing Om lichamelijk letsel te voorkomen wanneer u dit toestel in een rek

monteert of het daar een servicebeurt geeft, moet u speciale voorzorgsmaatregelen
nemen om ervoor te zorgen dat het toestel stabiel blijft. De onderstaande richtlijnen
worden verstrekt om uw veiligheid te verzekeren:

• De router moet in een stellage worden geïnstalleerd die aan een bouwsel is
verankerd.

• Dit toestel dient onderaan in het rek gemonteerd te worden als het toestel het enige
in het rek is.

• Wanneer u dit toestel in een gedeeltelijk gevuld rek monteert, dient u het rek van
onderen naar boven te laden met het zwaarste onderdeel onderaan in het rek.

• Als het rek voorzien is van stabiliseringshulpmiddelen, dient u de stabilisatoren te

monteren voordat u het toestel in het rek monteert of het daar een servicebeurt
geeft.

Varoitus Kun laite asetetaan telineeseen tai huolletaan sen ollessa telineessä, on
noudatettava erityisiä varotoimia järjestelmän vakavuuden säilyttämiseksi, jotta
vältytään loukkaantumiselta. Noudata seuraavia turvallisuusohjeita:

• Router on asennettava telineeseen, joka on kiinnitetty rakennukseen.

• Jos telineessä ei ole muita laitteita, aseta laite telineen alaosaan.

• Jos laite asetetaan osaksi täytettyyn telineeseen, aloita kuormittaminen sen alaosasta
kaikkein raskaimmalla esineellä ja siirry sitten sen yläosaan.

• Jos telinettä varten on vakaimet, asenna ne ennen laitteen asettamista telineeseen

tai sen huoltamista siinä.

Attention Pour éviter toute blessure corporelle pendant les opérations de montage ou
de réparation de cette unité en casier, il convient de prendre des précautions spéciales
afin de maintenir la stabilité du système. Les directives ci-dessous sont destinées à
assurer la protection du personnel:

• Le rack sur lequel est monté le router doit être fixé à la structure du bâtiment.

• Si cette unité constitue la seule unité montée en casier, elle doit être placée dans le
bas.

108 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

• Si cette unité est montée dans un casier partiellement rempli, charger le casier de
bas en haut en plaçant l'élément le plus lourd dans le bas.

• Si le casier est équipé de dispositifs stabilisateurs, installer les stabilisateurs avant

de monter ou de réparer l'unité en casier.

Warnung Zur Vermeidung von Körperverletzung beim Anbringen oder Warten dieser
Einheit in einem Gestell müssen Sie besondere Vorkehrungen treffen, um sicherzustellen,
daß das System stabil bleibt. Die folgenden Richtlinien sollen zur Gewährleistung Ihrer
Sicherheit dienen:

• Der router muß in einem Gestell installiert werden, das in der Gebäudestruktur
verankert ist.

• Wenn diese Einheit die einzige im Gestell ist, sollte sie unten im Gestell angebracht
werden.

• Bei Anbringung dieser Einheit in einem zum Teil gefüllten Gestell ist das Gestell von
unten nach oben zu laden, wobei das schwerste Bauteil unten im Gestell anzubringen
ist.

• Wird das Gestell mit Stabilisierungszubehör geliefert, sind zuerst die Stabilisatoren
zu installieren, bevor Sie die Einheit im Gestell anbringen oder sie warten.

Avvertenza Per evitare infortuni fisici durante il montaggio o la manutenzione di questa

unità in un supporto, occorre osservare speciali precauzioni per garantire che il sistema
rimanga stabile. Le seguenti direttive vengono fornite per garantire la sicurezza personale:

• Il router deve essere installato in un telaio, il quale deve essere fissato alla struttura
dell'edificio.

• Questa unità deve venire montata sul fondo del supporto, se si tratta dell'unica unità
da montare nel supporto.

• Quando questa unità viene montata in un supporto parzialmente pieno, caricare il

supporto dal basso all'alto, con il componente più pesante sistemato sul fondo del
supporto.

• Se il supporto è dotato di dispositivi stabilizzanti, installare tali dispositivi prima di

montare o di procedere alla manutenzione dell'unità nel supporto.

Advarsel Unngå fysiske skader under montering eller reparasjonsarbeid på denne

enheten når den befinner seg i et kabinett. Vær nøye med at systemet er stabilt. Følgende
retningslinjer er gitt for å verne om sikkerheten:

• Router må installeres i et stativ som er forankret til bygningsstrukturen.

• Denne enheten bør monteres nederst i kabinettet hvis dette er den eneste enheten i
kabinettet.

Copyright © 2010, Juniper Networks, Inc. 109

MX80 3D Universal Edge Router Hardware Guide

• Ved montering av denne enheten i et kabinett som er delvis fylt, skal kabinettet lastes
fra bunnen og opp med den tyngste komponenten nederst i kabinettet.

• Hvis kabinettet er utstyrt med stabiliseringsutstyr, skal stabilisatorene installeres før

montering eller utføring av reparasjonsarbeid på enheten i kabinettet.

Aviso Para se prevenir contra danos corporais ao montar ou reparar esta unidade numa
estante, deverá tomar precauções especiais para se certificar de que o sistema possui
um suporte estável. As seguintes directrizes ajudá-lo-ão a efectuar o seu trabalho com
segurança:

• O router deverá ser instalado numa prateleira fixa à estrutura do edificio.

• Esta unidade deverá ser montada na parte inferior da estante, caso seja esta a única
unidade a ser montada.

• Ao montar esta unidade numa estante parcialmente ocupada, coloque os itens mais
pesados na parte inferior da estante, arrumando-os de baixo para cima.

• Se a estante possuir um dispositivo de estabilização, instale-o antes de montar ou

reparar a unidade.

¡Atención! Para evitar lesiones durante el montaje de este equipo sobre un bastidor, o
posteriormente durante su mantenimiento, se debe poner mucho cuidado en que el
sistema quede bien estable. Para garantizar su seguridad, proceda según las siguientes
instrucciones:

• El router debe instalarse en un bastidor fijado a la estructura del edificio.

• Colocar el equipo en la parte inferior del bastidor, cuando sea la única unidad en el
mismo.

• Cuando este equipo se vaya a instalar en un bastidor parcialmente ocupado, comenzar

la instalación desde la parte inferior hacia la superior colocando el equipo más pesado
en la parte inferior.

• Si el bastidor dispone de dispositivos estabilizadores, instalar éstos antes de montar

o proceder al mantenimiento del equipo instalado en el bastidor.

Varning! För att undvika kroppsskada när du installerar eller utför underhållsarbete på
denna enhet på en ställning måste du vidta särskilda försiktighetsåtgärder för att
försäkra dig om att systemet står stadigt. Följande riktlinjer ges för att trygga din
säkerhet:

• Router måste installeras i en ställning som är förankrad i byggnadens struktur.

• Om denna enhet är den enda enheten på ställningen skall den installeras längst ned
på ställningen.

• Om denna enhet installeras på en delvis fylld ställning skall ställningen fyllas nedifrån
och upp, med de tyngsta enheterna längst ned på ställningen.

• Om ställningen är försedd med stabiliseringsdon skall dessa monteras fast innan

enheten installeras eller underhålls på ställningen.

110 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

Ramp Warning

WARNING: When installing the router, do not use a ramp inclined at more than 10
degrees.
Waarschuwing Gebruik een oprijplaat niet onder een hoek van meer dan 10 graden.

Varoitus Älä käytä sellaista kaltevaa pintaa, jonka kaltevuus ylittää 10 astetta.

Attention Ne pas utiliser une rampe dont l'inclinaison est supérieure à 10 degrés.

Warnung Keine Rampen mit einer Neigung von mehr als 10 Grad verwenden.

Avvertenza Non usare una rampa con pendenza superiore a 10 gradi.

Advarsel Bruk aldri en rampe som heller mer enn 10 grader.

Aviso Não utilize uma rampa com uma inclinação superior a 10 graus.

¡Atención! No usar una rampa inclinada más de 10 grados

Varning! Använd inte ramp med en lutning på mer än 10 grader.

Related Topics • General Safety Guidelines for M Series, MX Series, and T Series Routers on page 101

• Maintenance and Operational Safety Warnings for M Series, MX Series, and T Series
Routers on page 115

MX80 Chassis Lifting Guidelines

The weight of a fully configured chassis is about 30 lb (13.6 kg). Observe the following
guidelines for lifting and moving the router:

• Before moving the router, read the guidelines in “MX80 Site Preparation Checklist” on
page 23 to verify that the intended site meets the specified power, environmental, and
clearance requirements.

• Before lifting or moving the router, disconnect all external cables.

To lift routing devices and components, use the following lifting guidelines:

• Up to 39.7 lbs (18 kg) one person lift.

• 39.7 lbs (18 kg) to 70.5 lbs (32 kg) two or more person lift.

• 70.5 lbs (32 kg) to 121.2 lbs (55 kg) three or more person lift.

• Above 121.2 lbs (55 kg) material handling systems (such as levers, slings, lifts and
so on) must be used. When this is not practical, specially trained persons or systems
must be used (riggers or movers).

Copyright © 2010, Juniper Networks, Inc. 111

MX80 3D Universal Edge Router Hardware Guide

• As when lifting any heavy object, lift most of the weight with your legs rather than your
back. Keep your knees bent and your back relatively straight and avoid twisting your
body as you lift. Balance the load evenly and be sure that your footing is solid.

Related Topics • MX80 Site Preparation Checklist on page 23

• Installing the MX80 Chassis in the Rack on page 38

• General Safety Guidelines for M Series, MX Series, and T Series Routers on page 101

• General Safety Warnings for M Series, MX Series, and T Series Routers on page 102

• Installation Safety Warnings for M Series, MX Series, and T Series Routers on page 107

General Laser Safety Guidelines for M Series, MX Series, and T Series Routers
Devices with single-mode optical interfaces are equipped with laser transmitters, which
are considered a Class 1 Laser Product by the U.S. Food and Drug Administration, and
are evaluated as a Class 1 Laser Product per EN 60825–1 +A11 +A2 requirements.

When working around devices with optical interfaces, observe the following safety
guidelines to prevent eye injury:

• Do not look into unterminated ports or at fibers that connect to unknown sources.

• Do not examine unterminated optical ports with optical instruments.

• Avoid direct exposure to the beam.

WARNING: Unterminated optical connectors can emit invisible laser radiation. The lens
in the human eye focuses all the laser power on the retina, so focusing the eye directly
on a laser source—even a low-power laser—could permanently damage the eye.

Laser Safety Warnings for M Series, MX Series, and T Series Routers

• Class 1 Laser Product Warning on page 112
• Class 1 LED Product Warning on page 113
• Laser Beam Warning on page 113
• Radiation from Open Port Apertures Warning on page 114

Class 1 Laser Product Warning

WARNING: Class 1 laser product.

Waarschuwing Klasse-1 laser produkt.

Varoitus Luokan 1 lasertuote.

Attention Produit laser de classe I.

Warnung Laserprodukt der Klasse 1.

112 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

Avvertenza Prodotto laser di Classe 1.

Advarsel Laserprodukt av klasse 1.

Aviso Produto laser de classe 1.

¡Atención! Producto láser Clase I.

Varning! Laserprodukt av klass 1.

Class 1 LED Product Warning

WARNING: Class 1 LED product.

Waarschuwing Klasse 1 LED-product.

Varoitus Luokan 1 valodiodituote.

Attention Alarme de produit LED Class I.

Warnung Class 1 LED-Produktwarnung.

Avvertenza Avvertenza prodotto LED di Classe 1.

Advarsel LED-produkt i klasse 1.

Aviso Produto de classe 1 com LED.

¡Atención! Aviso sobre producto LED de Clase 1.

Varning! Lysdiodprodukt av klass 1.

Laser Beam Warning

WARNING: Do not stare into the laser beam or view it directly with optical instruments.
Waarschuwing Niet in de straal staren of hem rechtstreeks bekijken met optische
instrumenten.

Varoitus Älä katso säteeseen äläkä tarkastele sitä suoraan optisen laitteen avulla.

Attention Ne pas fixer le faisceau des yeux, ni l'observer directement à l'aide

d'instruments optiques.

Warnung Nicht direkt in den Strahl blicken und ihn nicht direkt mit optischen Geräten
prüfen.

Avvertenza Non fissare il raggio con gli occhi né usare strumenti ottici per osservarlo
direttamente.

Copyright © 2010, Juniper Networks, Inc. 113

MX80 3D Universal Edge Router Hardware Guide

Advarsel Stirr eller se ikke direkte p strlen med optiske instrumenter.

Aviso Não olhe fixamente para o raio, nem olhe para ele directamente com instrumentos
ópticos.

¡Atención! No mirar fijamente el haz ni observarlo directamente con instrumentos

ópticos.

Varning! Rikta inte blicken in mot strålen och titta inte direkt på den genom optiska
instrument.

Radiation from Open Port Apertures Warning

WARNING: Because invisible radiation may be emitted from the aperture of the port
when no fiber cable is connected, avoid exposure to radiation and do not stare into
open apertures.
Waarschuwing Aangezien onzichtbare straling vanuit de opening van de poort kan
komen als er geen fiberkabel aangesloten is, dient blootstelling aan straling en het
kijken in open openingen vermeden te worden.

Varoitus Koska portin aukosta voi emittoitua näkymätöntä säteilyä, kun kuitukaapelia
ei ole kytkettynä, vältä säteilylle altistumista äläkä katso avoimiin aukkoihin.

Attention Des radiations invisibles à l'il nu pouvant traverser l'ouverture du port

lorsqu'aucun câble en fibre optique n'y est connecté, il est recommandé de ne pas
regarder fixement l'intérieur de ces ouvertures.

Warnung Aus der Port-Öffnung können unsichtbare Strahlen emittieren, wenn kein
Glasfaserkabel angeschlossen ist. Vermeiden Sie es, sich den Strahlungen auszusetzen,
und starren Sie nicht in die Öffnungen!

Avvertenza Quando i cavi in fibra non sono inseriti, radiazioni invisibili possono essere
emesse attraverso l'apertura della porta. Evitate di esporvi alle radiazioni e non guardate
direttamente nelle aperture.

Advarsel Unngå utsettelse for stråling, og stirr ikke inn i åpninger som er åpne, fordi
usynlig stråling kan emiteres fra portens åpning når det ikke er tilkoblet en fiberkabel.

Aviso Dada a possibilidade de emissão de radiação invisível através do orifício da via

de acesso, quando esta não tiver nenhum cabo de fibra conectado, deverá evitar a
exposição à radiação e não deverá olhar fixamente para orifícios que se encontrarem
a descoberto.

¡Atención! Debido a que la apertura del puerto puede emitir radiación invisible cuando
no existe un cable de fibra conectado, evite mirar directamente a las aperturas para no
exponerse a la radiación.

114 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

Varning! Osynlig strålning kan avges från en portöppning utan ansluten fiberkabel och
du bör därför undvika att bli utsatt för strålning genom att inte stirra in i oskyddade
öppningar.

Related Topics • General Safety Guidelines for M Series, MX Series, and T Series Routers on page 101

• General Safety Warnings for M Series, MX Series, and T Series Routers on page 102

• Installation Safety Warnings for M Series, MX Series, and T Series Routers on page 107

Maintenance and Operational Safety Warnings for M Series, MX Series, and T Series Routers
As you maintain the router, observe the following warnings:

• Battery Handling Warning on page 115

• Jewelry Removal Warning on page 116
• Lightning Activity Warning on page 117
• Operating Temperature Warning on page 118
• Product Disposal Warning on page 119

Battery Handling Warning

WARNING: Replacing the battery incorrectly might result in an explosion. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions.
Waarschuwing Er is ontploffingsgevaar als de batterij verkeerd vervangen wordt. Vervang
de batterij slechts met hetzelfde of een equivalent type dat door de fabrikant aanbevolen
is. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften weggeworpen te
worden.

Varoitus Räjähdyksen vaara, jos akku on vaihdettu väärään akkuun. Käytä vaihtamiseen
ainoastaan saman- tai vastaavantyyppistä akkua, joka on valmistajan suosittelema.
Hävitä käytetyt akut valmistajan ohjeiden mukaan.

Attention Danger d'explosion si la pile n'est pas remplacée correctement. Ne la

remplacer que par une pile de type semblable ou équivalent, recommandée par le
fabricant. Jeter les piles usagées conformément aux instructions du fabricant.

Warnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie
die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Avvertenza Pericolo di esplosione se la batteria non è installata correttamente. Sostituire

solo con una di tipo uguale o equivalente, consigliata dal produttore. Eliminare le batterie
usate secondo le istruzioni del produttore.

Copyright © 2010, Juniper Networks, Inc. 115

MX80 3D Universal Edge Router Hardware Guide

Advarsel Det kan være fare for eksplosjon hvis batteriet skiftes på feil måte. Skift kun
med samme eller tilsvarende type som er anbefalt av produsenten. Kasser brukte
batterier i henhold til produsentens instruksjoner.

Aviso Existe perigo de explosão se a bateria for substituída incorrectamente. Substitua

a bateria por uma bateria igual ou de um tipo equivalente recomendado pelo fabricante.
Destrua as baterias usadas conforme as instruções do fabricante.

¡Atención! Existe peligro de explosión si la batería se reemplaza de manera incorrecta.

Reemplazar la batería exclusivamente con el mismo tipo o el equivalente recomendado
por el fabricante. Desechar las baterías gastadas según las instrucciones del fabricante.

Varning! Explosionsfara vid felaktigt batteribyte. Ersätt endast batteriet med samma
batterityp som rekommenderas av tillverkaren eller motsvarande. Följ tillverkarens
anvisningar vid kassering av använda batterier.

Jewelry Removal Warning

WARNING: Before working on equipment that is connected to power lines, remove

jewelry, including rings, necklaces, and watches. Metal objects heat up when connected
to power and ground and can cause serious burns or weld the metal object to the
terminals.
Waarschuwing Alvorens aan apparatuur te werken die met elektrische leidingen is
verbonden, sieraden (inclusief ringen, kettingen en horloges) verwijderen. Metalen
voorwerpen worden warm wanneer ze met stroom en aarde zijn verbonden, en kunnen
ernstige brandwonden veroorzaken of het metalen voorwerp aan de aansluitklemmen
lassen.

Varoitus Ennen kuin työskentelet voimavirtajohtoihin kytkettyjen laitteiden parissa, ota

pois kaikki korut (sormukset, kaulakorut ja kellot mukaan lukien). Metalliesineet
kuumenevat, kun ne ovat yhteydessä sähkövirran ja maan kanssa, ja ne voivat aiheuttaa
vakavia palovammoja tai hitsata metalliesineet kiinni liitäntänapoihin.

Attention Avant d'accéder à cet équipement connecté aux lignes électriques, ôter tout
bijou (anneaux, colliers et montres compris). Lorsqu'ils sont branchés à l'alimentation
et reliés à la terre, les objets métalliques chauffent, ce qui peut provoquer des blessures
graves ou souder l'objet métallique aux bornes.

Warnung Vor der Arbeit an Geräten, die an das Netz angeschlossen sind, jeglichen
Schmuck (einschließlich Ringe, Ketten und Uhren) abnehmen. Metallgegenstände
erhitzen sich, wenn sie an das Netz und die Erde angeschlossen werden, und können
schwere Verbrennungen verursachen oder an die Anschlußklemmen angeschweißt
werden.

Avvertenza Prima di intervenire su apparecchiature collegate alle linee di alimentazione,

togliersi qualsiasi monile (inclusi anelli, collane, braccialetti ed orologi). Gli oggetti

116 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

metallici si riscaldano quando sono collegati tra punti di alimentazione e massa: possono
causare ustioni gravi oppure il metallo può saldarsi ai terminali.

Advarsel Fjern alle smykker (inkludert ringer, halskjeder og klokker) før du skal arbeide
på utstyr som er koblet til kraftledninger. Metallgjenstander som er koblet til
kraftledninger og jord blir svært varme og kan forårsake alvorlige brannskader eller
smelte fast til polene.

Aviso Antes de trabalhar em equipamento que esteja ligado a linhas de corrente, retire
todas as jóias que estiver a usar (incluindo anéis, fios e relógios). Os objectos metálicos
aquecerão em contacto com a corrente e em contacto com a ligação à terra, podendo
causar queimaduras graves ou ficarem soldados aos terminais.

¡Atención! Antes de operar sobre equipos conectados a líneas de alimentación, quitarse

las joyas (incluidos anillos, collares y relojes). Los objetos de metal se calientan cuando
se conectan a la alimentación y a tierra, lo que puede ocasionar quemaduras graves o
que los objetos metálicos queden soldados a los bornes.

Varning! Tag av alla smycken (inklusive ringar, halsband och armbandsur) innan du
arbetar på utrustning som är kopplad till kraftledningar. Metallobjekt hettas upp när
de kopplas ihop med ström och jord och kan förorsaka allvarliga brännskador;
metallobjekt kan också sammansvetsas med kontakterna.

Lightning Activity Warning

WARNING: Do not work on the system or connect or disconnect cables during periods
of lightning activity.
Waarschuwing Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het
systeem te werken of kabels aan te sluiten of te ontkoppelen.

Varoitus Älä työskentele järjestelmän parissa äläkä yhdistä tai irrota kaapeleita
ukkosilmalla.

Attention Ne pas travailler sur le système ni brancher ou débrancher les câbles pendant
un orage.

Warnung Arbeiten Sie nicht am System und schließen Sie keine Kabel an bzw. trennen
Sie keine ab, wenn es gewittert.

Avvertenza Non lavorare sul sistema o collegare oppure scollegare i cavi durante un
temporale con fulmini.

Advarsel Utfør aldri arbeid på systemet, eller koble kabler til eller fra systemet når det
tordner eller lyner.

Aviso Não trabalhe no sistema ou ligue e desligue cabos durante períodos de mau
tempo (trovoada).

Copyright © 2010, Juniper Networks, Inc. 117

MX80 3D Universal Edge Router Hardware Guide

¡Atención! No operar el sistema ni conectar o desconectar cables durante el transcurso

de descargas eléctricas en la atmósfera.

Varning! Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller koppla
loss kablar.

Operating Temperature Warning

WARNING: To prevent the router from overheating, do not operate it in an area that
ο ο
exceeds the maximum recommended ambient temperature of 104 F (40 C). To prevent
airflow restriction, allow at least 6 inches (15.2 cm) of clearance around the ventilation
openings.
Waarschuwing Om te voorkomen dat welke router van de router dan ook oververhit
raakt, dient u deze niet te bedienen op een plaats waar de maximale aanbevolen
ο
omgevingstemperatuur van 40 C wordt overschreden. Om te voorkomen dat de
luchtstroom wordt beperkt, dient er minstens 15,2 cm speling rond de
ventilatie-openingen te zijn.

Varoitus Ettei router-sarjan reititin ylikuumentuisi, sitä ei saa käyttää tilassa, jonka
ο
lämpötila ylittää korkeimman suositellun ympäristölämpötilan 40 C. Ettei ilmanvaihto
estyisi, tuuletusaukkojen ympärille on jätettävä ainakin 15,2 cm tilaa.

Attention Pour éviter toute surchauffe des routeurs de la gamme router, ne l'utilisez
ο
pas dans une zone où la température ambiante est supérieure à 40 C. Pour permettre
un flot d'air constant, dégagez un espace d'au moins 15,2 cm autour des ouvertures de
ventilations.

Warnung Um einen router der router vor Überhitzung zu schützen, darf dieser nicht in
einer Gegend betrieben werden, in der die Umgebungstemperatur das empfohlene
ο
Maximum von 40 C überschreitet. Um Lüftungsverschluß zu verhindern, achten Sie
darauf, daß mindestens 15,2 cm lichter Raum um die Lüftungsöffnungen herum frei
bleibt.

Avvertenza Per evitare il surriscaldamento dei router, non adoperateli in un locale che
ο
ecceda la temperatura ambientale massima di 40 C. Per evitare che la circolazione
dell'aria sia impedita, lasciate uno spazio di almeno 15.2 cm di fronte alle aperture delle
ventole.

Advarsel Unngå overoppheting av eventuelle rutere i router Disse skal ikke brukes på
ο ο
steder der den anbefalte maksimale omgivelsestemperaturen overstiger 40 C (104 F).
Sørg for at klaringen rundt lufteåpningene er minst 15,2 cm (6 tommer) for å forhindre
nedsatt luftsirkulasjon.

Aviso Para evitar o sobreaquecimento do encaminhador router, não utilize este

ο
equipamento numa área que exceda a temperatura máxima recomendada de 40 C.

118 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

Para evitar a restrição à circulação de ar, deixe pelo menos um espaço de 15,2 cm à
volta das aberturas de ventilação.

¡Atención! Para impedir que un encaminador de la serie router se recaliente, no lo haga

funcionar en un área en la que se supere la temperatura ambiente máxima recomendada
ο
de 40 C. Para impedir la restricción de la entrada de aire, deje un espacio mínimo de
15,2 cm alrededor de las aperturas para ventilación.

Varning! Förhindra att en router överhettas genom att inte använda den i ett område
ο
där den maximalt rekommenderade omgivningstemperaturen på 40 C överskrids.
Förhindra att luftcirkulationen inskränks genom att se till att det finns fritt utrymme på
minst 15,2 cm omkring ventilationsöppningarna.

Product Disposal Warning

WARNING: Disposal of this product must be handled according to all national laws and
regulations.
Waarschuwing Dit produkt dient volgens alle landelijke wetten en voorschriften te
worden afgedankt.

Varoitus Tämän tuotteen lopullisesta hävittämisestä tulee huolehtia kaikkia

valtakunnallisia lakeja ja säännöksiä noudattaen.

Attention La mise au rebut définitive de ce produit doit être effectuée conformément

à toutes les lois et réglementations en vigueur.

Warnung Dieses Produkt muß den geltenden Gesetzen und Vorschriften entsprechend
entsorgt werden.

Avvertenza L'eliminazione finale di questo prodotto deve essere eseguita osservando

le normative italiane vigenti in materia

Advarsel Endelig disponering av dette produktet må skje i henhold til nasjonale lover
og forskrifter.

Aviso A descartagem final deste produto deverá ser efectuada de acordo com os
regulamentos e a legislação nacional.

¡Atención! El desecho final de este producto debe realizarse según todas las leyes y
regulaciones nacionales

Varning! Slutlig kassering av denna produkt bör skötas i enlighet med landets alla lagar
och föreskrifter.

Related Topics • General Safety Guidelines for M Series, MX Series, and T Series Routers on page 101

• General Safety Warnings for M Series, MX Series, and T Series Routers on page 102

Copyright © 2010, Juniper Networks, Inc. 119

MX80 3D Universal Edge Router Hardware Guide

General Electrical Safety Guidelines and Warnings for the MX80 Router
• General Electrical Safety Warnings for M Series, MX Series, and T Series
Routers on page 120
• General Electrical Safety Guidelines and Electrical Codes for M Series, MX Series, and
T Series Routers on page 123
• In Case of an Electrical Accident on page 124
• AC Power Electrical Safety Guidelines and Warnings for MX80 Routers on page 124
• MX80 DC Power Electrical Safety Guidelines on page 125
• DC Power Electrical Safety Warnings for M Series, MX Series, and T Series
Routers on page 126
General Electrical Safety Warnings for M Series, MX Series, and T Series Routers
• Grounded Equipment Warning on page 120
• Grounding Requirements and Warning on page 121
• Midplane Energy Hazard Warning on page 121
• Multiple Power Supplies Disconnection Warning on page 122
• Power Disconnection Warning on page 122

Grounded Equipment Warning

WARNING: The router is intended to be grounded. Ensure that the router is connected
to earth ground during normal use.
Waarschuwing Deze apparatuur hoort geaard te worden Zorg dat de host-computer
tijdens normaal gebruik met aarde is verbonden.

Varoitus Tämä laitteisto on tarkoitettu maadoitettavaksi. Varmista, että isäntälaite on

yhdistetty maahan normaalikäytön aikana.

Attention Cet équipement doit être relié à la terre. S'assurer que l'appareil hôte est relié
à la terre lors de l'utilisation normale.

Warnung Dieses Gerät muß geerdet werden. Stellen Sie sicher, daß das Host-Gerät
während des normalen Betriebs an Erde gelegt ist.

Avvertenza Questa apparecchiatura deve essere collegata a massa. Accertarsi che il

dispositivo host sia collegato alla massa di terra durante il normale utilizzo.

Advarsel Dette utstyret skal jordes. Forviss deg om vertsterminalen er jordet ved normalt
bruk.

Aviso Este equipamento deverá estar ligado à terra. Certifique-se que o host se encontra
ligado à terra durante a sua utilização normal.

¡Atención! Este equipo debe conectarse a tierra. Asegurarse de que el equipo principal
esté conectado a tierra durante el uso normal.

120 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

Varning! Denna utrustning är avsedd att jordas. Se till att värdenheten är jordad vid
normal användning.

Grounding Requirements and Warning

An insulated grounding conductor that is identical in size to the grounded and ungrounded
branch circuit supply conductors, but is identifiable by green and yellow stripes, is installed
as part of the branch circuit that supplies the unit. The grounding conductor is a separately
derived system at the supply transformer or motor generator set.

WARNING: When installing the router, the ground connection must always be made
first and disconnected last.
Waarschuwing Bij de installatie van het toestel moet de aardverbinding altijd het eerste
worden gemaakt en het laatste worden losgemaakt.

Varoitus Laitetta asennettaessa on maahan yhdistäminen aina tehtävä ensiksi ja

maadoituksen irti kytkeminen viimeiseksi.

Attention Lors de l'installation de l'appareil, la mise à la terre doit toujours être connectée
en premier et déconnectée en dernier.

Warnung Der Erdanschluß muß bei der Installation der Einheit immer zuerst hergestellt
und zuletzt abgetrennt werden.

Avvertenza In fase di installazione dell'unità, eseguire sempre per primo il collegamento

a massa e disconnetterlo per ultimo.

Advarsel Når enheten installeres, må jordledningen alltid tilkobles først og frakobles

sist.

Aviso Ao instalar a unidade, a ligação à terra deverá ser sempre a primeira a ser ligada,
e a última a ser desligada.

¡Atención! Al instalar el equipo, conectar la tierra la primera y desconectarla la última.

Varning! Vid installation av enheten måste jordledningen alltid anslutas först och
kopplas bort sist.

Midplane Energy Hazard Warning

WARNING: High levels of electrical energy are distributed across the router midplane.
Be careful not to contact the midplane connectors, or any component connected to
the midplane, with any metallic object while servicing components installed in the
router.

Copyright © 2010, Juniper Networks, Inc. 121

MX80 3D Universal Edge Router Hardware Guide

Multiple Power Supplies Disconnection Warning

WARNING: The router has more than one power supply connection. All connections
must be removed completely to remove power from the unit completely.
Waarschuwing Deze eenheid heeft meer dan één stroomtoevoerverbinding; alle
verbindingen moeten volledig worden verwijderd om de stroom van deze eenheid
volledig te verwijderen.

Varoitus Tässä laitteessa on useampia virtalähdekytkentöjä. Kaikki kytkennät on

irrotettava kokonaan, jotta virta poistettaisiin täysin laitteesta.

Attention Cette unité est équipée de plusieurs raccordements d'alimentation. Pour

supprimer tout courant électrique de l'unité, tous les cordons d'alimentation doivent
être débranchés.

Warnung Diese Einheit verfügt über mehr als einen Stromanschluß; um Strom gänzlich
von der Einheit fernzuhalten, müssen alle Stromzufuhren abgetrennt sein.

Avvertenza Questa unità ha più di una connessione per alimentatore elettrico; tutte le
connessioni devono essere completamente rimosse per togliere l'elettricità dall'unità.

Advarsel Denne enheten har mer enn én strømtilkobling. Alle tilkoblinger må kobles
helt fra for å eliminere strøm fra enheten.

Aviso Este dispositivo possui mais do que uma conexão de fonte de alimentação de
energia; para poder remover a fonte de alimentação de energia, deverão ser
desconectadas todas as conexões existentes.

¡Atención! Esta unidad tiene más de una conexión de suministros de alimentación;

para eliminar la alimentación por completo, deben desconectarse completamente
todas las conexiones.

Varning! Denna enhet har mer än en strömförsörjningsanslutning; alla anslutningar

måste vara helt avlägsnade innan strömtillförseln till enheten är fullständigt bruten.

Power Disconnection Warning

WARNING: Before working on the chassis or near power supplies, switch off the power
at the DC circuit breaker.
Waarschuwing Voordat u aan een frame of in de nabijheid van voedingen werkt, dient
u bij wisselstroom toestellen de stekker van het netsnoer uit het stopcontact te halen;
voor gelijkstroom toestellen dient u de stroom uit te schakelen bij de stroomverbreker.

Varoitus Kytke irti vaihtovirtalaitteiden virtajohto ja katkaise tasavirtalaitteiden virta

suojakytkimellä, ennen kuin teet mitään asennuspohjalle tai työskentelet virtalähteiden
läheisyydessä.

122 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

Attention Avant de travailler sur un châssis ou à proximité d'une alimentation électrique,

débrancher le cordon d'alimentation des unités en courant alternatif; couper
l'alimentation des unités en courant continu au niveau du disjoncteur.

Warnung Bevor Sie an einem Chassis oder in der Nähe von Netzgeräten arbeiten, ziehen
Sie bei Wechselstromeinheiten das Netzkabel ab bzw. schalten Sie bei
Gleichstromeinheiten den Strom am Unterbrecher ab.

Avvertenza Prima di lavorare su un telaio o intorno ad alimentatori, scollegare il cavo

di alimentazione sulle unità CA; scollegare l'alimentazione all'interruttore automatico
sulle unità CC.

Advarsel Før det utføres arbeid på kabinettet eller det arbeides i nærheten av
strømforsyningsenheter, skal strømledningen trekkes ut p vekselstrømsenheter og
strømmen kobles fra ved strømbryteren på likestrømsenheter.

Aviso Antes de trabalhar num chassis, ou antes de trabalhar perto de unidades de

fornecimento de energia, desligue o cabo de alimentação nas unidades de corrente
alternada; desligue a corrente no disjuntor nas unidades de corrente contínua.

¡Atención! Antes de manipular el chasis de un equipo o trabajar cerca de una fuente

de alimentación, desenchufar el cable de alimentación en los equipos de corriente
alterna (CA); cortar la alimentación desde el interruptor automático en los equipos de
corriente continua (CC).

Varning! Innan du arbetar med ett chassi eller nära strömförsörjningsenheter skall du
för växelströmsenheter dra ur nätsladden och för likströmsenheter bryta strömmen vid
överspänningsskyddet.

Related Topics • DC Power Electrical Safety Warnings for M Series, MX Series, and T Series Routers on
page 126

General Electrical Safety Guidelines and Electrical Codes for M Series, MX Series,
and T Series Routers
• Install the router in compliance with the following local, national, or international
electrical codes:

• United States—National Fire Protection Association (NFPA 70), United States

National Electrical Code.

• Canada—Canadian Electrical Code, Part 1, CSA C22.1.

• Other countries—International Electromechanical Commission (IEC) 60364, Part 1

through Part 7.

• Locate the emergency power-off switch for the room in which you are working so that
if an electrical accident occurs, you can quickly turn off the power.

• Do not work alone if potentially hazardous conditions exist anywhere in your workspace.

Copyright © 2010, Juniper Networks, Inc. 123

MX80 3D Universal Edge Router Hardware Guide

• Never assume that power is disconnected from a circuit. Always check the circuit before
starting to work.

• Carefully look for possible hazards in your work area, such as moist floors, ungrounded
power extension cords, and missing safety grounds.

• Operate the router within marked electrical ratings and product usage instructions.

• For the router and peripheral equipment to function safely and correctly, use the cables
and connectors specified for the attached peripheral equipment, and make certain
they are in good condition.

Many router components can be removed and replaced without powering off or
disconnecting power to the router. Never install equipment if it appears damaged.

In Case of an Electrical Accident

If an electrical accident results in an injury, take the following actions in this order:

1. Use caution. Be aware of potentially hazardous conditions that could cause further
injury.

2. Disconnect power from the router.

3. If possible, send another person to get medical aid. Otherwise, assess the condition
of the victim, then call for help.

AC Power Electrical Safety Guidelines and Warnings for MX80 Routers

The following electrical safety guidelines apply to an AC-powered router:

• You can order three-wire electrical cords with a grounding-type plug that fits only a
grounding-type power outlet. Do not circumvent this safety feature. Equipment
grounding should comply with local and national electrical codes.

• You must provide an external listed circuit breaker rated minimum 15 A (110 VAC) for
each AC power supply.

• The cores in the mains lead are colored in accordance with the following code:

• Green and yellow—Earth

• Blue—Neutral

• Brown—Live

WARNING: The attached power cable is only for this product. Do not use the cable for
another product.

124 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

The power cable warning in Japanese is as follows:

MX80 DC Power Electrical Safety Guidelines

The following electrical safety guidelines apply to a DC-powered router:

• A DC-powered router is equipped with a DC terminal block that is rated for the power
requirements of a maximally configured router. To supply sufficient power, terminate
the DC input wiring on a facility DC source capable of supplying at least 13 A @ –48 VDC
per input for each power supply. We recommend that the 48-VDC facility DC source
should be equipped with a circuit breaker rated at 25 A (–48 VDC) minimum, or as
required by local code.

Incorporate an easily accessible disconnect device into the facility wiring. In the United
States and Canada, the 48 VDC facility should be equipped with a circuit breaker rated
a minimum of 125 percent of the power provisioned for the input in accordance with
the National Electrical Code in the US and the Canadian Electrical Code in Canada.

• Run two wires from the circuit breaker box to a source of 48 VDC. Use appropriate
gauge wire to handle up to 25 A.

• Be sure to connect the ground wire or conduit to a solid office (earth) ground. A closed
loop ring is recommended for terminating the ground conductor at the ground stud.

• A DC-powered router that is equipped with a DC terminal block is intended only for
installation in a restricted access location. In the United States, a restricted access
area is one in accordance with Articles 110-16, 110-17, and 110-18 of the National Electrical
Code ANSI/NFPA 70.

NOTE: Primary overcurrent protection is provided by the building circuit breaker. This
breaker should protect against excess currents, short circuits, and earth faults in
accordance with NEC ANSI/NFPA70.

• Ensure that the polarity of the DC input wiring is correct. Under certain conditions,
connections with reversed polarity might trip the primary circuit breaker or damage
the equipment.

• For personal safety, connect the green and yellow wire to safety (earth) ground at both
the router and the supply side of the DC wiring.

Copyright © 2010, Juniper Networks, Inc. 125

MX80 3D Universal Edge Router Hardware Guide

• The marked input voltage of –48 VDC for a DC-powered router is the nominal voltage
associated with the battery circuit, and any higher voltages are only to be associated
with float voltages for the charging function.

• Because the router is a positive ground system, you must connect the positive lead to
the terminal labeled RTN, the negative lead to the terminal labeled –48V, and the earth
ground to the chassis grounding points.

DC Power Electrical Safety Warnings for M Series, MX Series, and T Series Routers
When working with DC-powered equipment, observe the following warnings:

• DC Power Copper Conductors Warning on page 126

• DC Power Disconnection Warning on page 126
• DC Power Wiring Terminations Warning on page 128

DC Power Copper Conductors Warning

WARNING: Use copper conductors only.

Waarschuwing Gebruik alleen koperen geleiders.

Varoitus Käytä vain kuparijohtimia.

Attention Utilisez uniquement des conducteurs en cuivre.

Warnung Verwenden Sie ausschließlich Kupferleiter.

Avvertenza Usate unicamente dei conduttori di rame.

Advarsel Bruk bare kobberledninger.

Aviso Utilize apenas fios condutores de cobre.

¡Atención! Emplee sólo conductores de cobre.

Varning! Använd endast ledare av koppar.

DC Power Disconnection Warning

WARNING: Before performing any procedures on power supplies, ensure that power is
removed from the DC circuit. To ensure that all power is off, locate the circuit breaker
on the panel board that services the DC circuit, switch the circuit breaker to the OFF
position, and tape the switch handle of the circuit breaker in the OFF position.
Waarschuwing Voordat u een van de onderstaande procedures uitvoert, dient u te
controleren of de stroom naar het gelijkstroom circuit uitgeschakeld is. Om u ervan te
verzekeren dat alle stroom UIT is geschakeld, kiest u op het schakelbord de
stroomverbreker die het gelijkstroom circuit bedient, draait de stroomverbreker naar
de UIT positie en plakt de schakelaarhendel van de stroomverbreker met plakband in
de UIT positie vast.

126 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

Varoitus Varmista, että tasavirtapiirissä ei ole virtaa ennen seuraavien toimenpiteiden

suorittamista. Varmistaaksesi, että virta on KATKAISTU täysin, paikanna tasavirrasta
huolehtivassa kojetaulussa sijaitseva suojakytkin, käännä suojakytkin
KATKAISTU-asentoon ja teippaa suojakytkimen varsi niin, että se pysyy
KATKAISTU-asennossa.

Attention Avant de pratiquer l'une quelconque des procédures ci-dessous, vérifier que
le circuit en courant continu n'est plus sous tension. Pour en être sûr, localiser le
disjoncteur situé sur le panneau de service du circuit en courant continu, placer le
disjoncteur en position fermée (OFF) et, à l'aide d'un ruban adhésif, bloquer la poignée
du disjoncteur en position OFF.

Warnung Vor Ausführung der folgenden Vorgänge ist sicherzustellen, daß die
Gleichstromschaltung keinen Strom erhält. Um sicherzustellen, daß sämtlicher Strom
abgestellt ist, machen Sie auf der Schalttafel den Unterbrecher für die
Gleichstromschaltung ausfindig, stellen Sie den Unterbrecher auf AUS, und kleben Sie
den Schaltergriff des Unterbrechers mit Klebeband in der AUS-Stellung fest.

Avvertenza Prima di svolgere una qualsiasi delle procedure seguenti, verificare che il
circuito CC non sia alimentato. Per verificare che tutta l'alimentazione sia scollegata
(OFF), individuare l'interruttore automatico sul quadro strumenti che alimenta il circuito
CC, mettere l'interruttore in posizione OFF e fissarlo con nastro adesivo in tale posizione.

Advarsel Før noen av disse prosedyrene utføres, kontroller at strømmen er frakoblet

likestrømkretsen. Sørg for at all strøm er slått AV. Dette gjøres ved å lokalisere
strømbryteren på brytertavlen som betjener likestrømkretsen, slå strømbryteren AV og
teipe bryterhåndtaket på strømbryteren i AV-stilling.

Aviso Antes de executar um dos seguintes procedimentos, certifique-se que desligou

a fonte de alimentação de energia do circuito de corrente contínua. Para se assegurar
que toda a corrente foi DESLIGADA, localize o disjuntor no painel que serve o circuito
de corrente contínua e coloque-o na posição OFF (Desligado), segurando nessa posição
a manivela do interruptor do disjuntor com fita isoladora.

¡Atención! Antes de proceder con los siguientes pasos, comprobar que la alimentación
del circuito de corriente continua (CC) esté cortada (OFF). Para asegurarse de que toda
la alimentación esté cortada (OFF), localizar el interruptor automático en el panel que
alimenta al circuito de corriente continua, cambiar el interruptor automático a la posición
de Apagado (OFF), y sujetar con cinta la palanca del interruptor automático en posición
de Apagado (OFF).

Varning! Innan du utför någon av följande procedurer måste du kontrollera att

strömförsörjningen till likströmskretsen är bruten. Kontrollera att all strömförsörjning
är BRUTEN genom att slå AV det överspänningsskydd som skyddar likströmskretsen
och tejpa fast överspänningsskyddets omkopplare i FRÅN-läget.

Copyright © 2010, Juniper Networks, Inc. 127

MX80 3D Universal Edge Router Hardware Guide

DC Power Wiring Terminations Warning

WARNING: When stranded wiring is required, use approved wiring terminations, such
as closed-loop or spade-type with upturned lugs. These terminations should be the
appropriate size for the wires and should clamp both the insulation and conductor.
Waarschuwing Wanneer geslagen bedrading vereist is, dient u bedrading te gebruiken
die voorzien is van goedgekeurde aansluitingspunten, zoals het gesloten-lus type of
het grijperschop type waarbij de aansluitpunten omhoog wijzen. Deze aansluitpunten
dienen de juiste maat voor de draden te hebben en dienen zowel de isolatie als de
geleider vast te klemmen.

Varoitus Jos säikeellinen johdin on tarpeen, käytä hyväksyttyä johdinliitäntää, esimerkiksi

suljettua silmukkaa tai kourumaista liitäntää, jossa on ylöspäin käännetyt kiinnityskorvat.
Tällaisten liitäntöjen tulee olla kooltaan johtimiin sopivia ja niiden tulee puristaa yhteen
sekä eristeen että johdinosan.

Attention Quand des fils torsadés sont nécessaires, utiliser des douilles terminales
homologuées telles que celles à circuit fermé ou du type à plage ouverte avec cosses
rebroussées. Ces douilles terminales doivent être de la taille qui convient aux fils et
doivent être refermées sur la gaine isolante et sur le conducteur.

Warnung Wenn Litzenverdrahtung erforderlich ist, sind zugelassene

Verdrahtungsabschlüsse, z.B. Ringoesen oder gabelförmige Kabelschuhe mit nach oben
gerichteten Enden zu verwenden. Diese Abschlüsse sollten die angemessene Größe für
die Drähte haben und sowohl die Isolierung als auch den Leiter festklemmen.

Avvertenza Quando occorre usare trecce, usare connettori omologati, come quelli a
occhiello o a forcella con linguette rivolte verso l'alto. I connettori devono avere la
misura adatta per il cablaggio e devono serrare sia l'isolante che il conduttore.

Advarsel Hvis det er nødvendig med flertrådede ledninger, brukes godkjente

ledningsavslutninger, som for eksempel lukket sløyfe eller spadetype med oppoverbøyde
kabelsko. Disse avslutningene skal ha riktig størrelse i forhold til ledningene, og skal
klemme sammen både isolasjonen og lederen.

Aviso Quando forem requeridas montagens de instalação eléctrica de cabo torcido,

use terminações de cabo aprovadas, tais como, terminações de cabo em circuito
fechado e planas com terminais de orelha voltados para cima. Estas terminações de
cabo deverão ser do tamanho apropriado para os respectivos cabos, e deverão prender
simultaneamente o isolamento e o fio condutor.

¡Atención! Cuando se necesite hilo trenzado, utilizar terminales para cables

homologados, tales como las de tipo "bucle cerrado" o "espada", con las lengüetas de
conexión vueltas hacia arriba. Estos terminales deberán ser del tamaño apropiado para
los cables que se utilicen, y tendrán que sujetar tanto el aislante como el conductor.

Varning! När flertrådiga ledningar krävs måste godkända ledningskontakter användas,

t.ex. kabelsko av sluten eller öppen typ med uppåtvänd tapp. Storleken på dessa

128 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

kontakter måste vara avpassad till ledningarna och måste kunna hålla både isoleringen
och ledaren fastklämda.

Related Topics • General Electrical Safety Warnings for M Series, MX Series, and T Series Routers on
page 120

Agency Approvals and Compliance Statements for the MX80 Router

• Agency Approvals for MX80 Routers on page 129

• Compliance Statements for NEBS for MX80 Routers on page 130
• Compliance Statements for EMC Requirements for the MX80 Router on page 131
• Compliance Statements for Environmental Requirements for M Series, MX Series, and
T Series Routers on page 133
• Compliance Statements for Acoustic Noise for MX80 Routers on page 133

Agency Approvals for MX80 Routers

The MX80 router complies with the following standards:

• Safety

• CAN/CSA-22.2 No. 60950-00/UL 1950 Third Edition, Safety of Information

Technology Equipment

• UL 60950-1 Information Technology Equipment - Safety - Part 1: General

Requirements

• EN 60950-1 European Norm, Safety of Information Technology Equipment

Copyright © 2010, Juniper Networks, Inc. 129

MX80 3D Universal Edge Router Hardware Guide

• IEC 60950-1 Information Technology Equipment - Safety - Part 1: General

Requirements (with country deviations)

• EN 60825-1 Safety of Laser Products - Part 1: Equipment Classification, Requirements

and User's Guide

• EMC

• EN 300 386 V1.3.3 Telecom Network Equipment - EMC Requirements

• EMI

• FCC Part 15 Class A USA Radiated Emissions

• EN 55022 Class A European Radiated Emissions

• VCCI Class A Japanese Radiated Emissions

• Immunity

• EN 55024 Information Technology Equipment Immunity Characteristics

• EN-61000-3-2 Power Line Harmonics

• EN-61000-3-3 Voltage Fluctuations and Flicker

• EN-61000-4-2 ESD

• EN-61000-4-3 Radiated Immunity

• EN-61000-4-4 EFT

• EN-61000-4-5 Surge

• EN-61000-4-6 Conducted Disturbances Immunity

• EN-61000-4-11 Voltage Dips and Sags

The router is designed to comply with the following standards:

• GR-63-Core: NEBS, Physical Protection

• GR-1089-Core: EMC and Electrical Safety for Network Telecommunications Equipment

• SR-3580 NEBS Criteria Levels (Level 3 Compliance)

Compliance Statements for NEBS for MX80 Routers

• The equipment is suitable for installation as part of the Common Bonding Network
(CBN).

• The equipment is suitable for installation in locations where the National Electrical
Code (NEC) applies.

• The battery return connection is to be treated as an isolated DC return (i.e. DC-I), as

defined in GR-1089-CORE.

130 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

Compliance Statements for EMC Requirements for the MX80 Router

• Canada on page 131
• European Community on page 131
• Declaration of Conformity on page 131
• Japan on page 132
• United States on page 133

Canada
This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

European Community
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

Declaration of Conformity
Figure 50 on page 132 shows the Declaration of Conformity for the router.

Copyright © 2010, Juniper Networks, Inc. 131

MX80 3D Universal Edge Router Hardware Guide

Figure 50: MX80 Declaration of Conformity

Japan

Translation from Japanese—This is a Class A product. In a domestic environment this

product may cause radio interference in which case the user may be required to take
adequate measures. VCCI-A

132 Copyright © 2010, Juniper Networks, Inc.

 Appendix A: Safety and Regulatory Compliance Information for the MX80 Router

United States
The router has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.

Compliance Statements for Environmental Requirements for M Series, MX Series, and T Series
Routers
Batteries in this product are not based on mercury, lead, or cadmium substances. The
batteries used in this product are in compliance with EU Directives 91/157/EEC, 93/86/EEC,
and 98/101/EEC. The product documentation includes instructional information about
the proper method of reclamation and recycling.

Related Topics • General Safety Guidelines for M Series, MX Series, and T Series Routers on page 101

• General Safety Warnings for M Series, MX Series, and T Series Routers on page 102

Compliance Statements for Acoustic Noise for MX80 Routers

• The emitted sound pressure is 70 dB(A) or less as per EN ISO 7779.

• Maschinenlärminformations-Verordnung - 3. GPSGV, der höchste Schalldruckpegel

beträgt 70 dB(A) oder weniger gemäss EN ISO 7779

Copyright © 2010, Juniper Networks, Inc. 133

MX80 3D Universal Edge Router Hardware Guide

134 Copyright © 2010, Juniper Networks, Inc.

APPENDIX B

MX80 Router Physical Specifications

• MX80 Router Physical Specifications on page 135

MX80 Router Physical Specifications

Table 14 on page 135 summarizes the physical specifications for the router chassis.

Table 14: MX80 Physical Specifications

Description Weight Width Depth Height

Fixed chassis Chassis with fan tray 19.2 in. (48.7 cm) 20.2 in. (51.3 cm) 3.5 in. (8.9 cm)
and power supplies:
28 lb (12.7 kg)

Modular chassis Chassis with fan tray, 19.2 in. (48.7 cm) 21.75 in. (55.2 cm) 3.5 in. (8.9 cm)
power supplies, and (including MIC release
MICs: 30 lb (13.6 kg) levers)

Air filter 0.1 lb (0.05 kg) 0.25 in. (0.64 cm) 18.43 in. 46.81 cm) 3.35 in. (8.5 cm)

MIC Maximum up to 1.2 lb 6.25 in. (15.9 cm) 6.8 in (17.3 cm) 1.2 in. (3.05 cm)
(0.54 kg)

Dual-wide MIC 1.9 lb (0.9 kg) 12.5 in. (31.75 cm) 6.8 in (17.3 cm) 1.2 in. (3.05 cm)

Fan tray 2.3 lb (1.04 kg) 2.75 in. (6.96 cm) 20.5 in. 52.07 cm) 3.35 in. (8.5 cm)

DC power supply 2.6 lb (1.18 kg) 2.8 in. (7.1 cm) 13.2 in. (33.5 cm) 1.6 in. (4.1 cm)

AC power supply 2.6 lb (1.18 kg) 2.8 in. (7.1 cm) 13.2 in. (33.5 cm) 1.6 in. (4.1 cm)

Related Topics • MX80 Router Overview on page 3

• MX80 Chassis Description on page 5

• MX80 Chassis Lifting Guidelines on page 111

Copyright © 2010, Juniper Networks, Inc. 135

MX80 3D Universal Edge Router Hardware Guide

136 Copyright © 2010, Juniper Networks, Inc.

APPENDIX C

MX80 Router Environmental

Specifications

• MX80 Router Environmental Specifications on page 137

MX80 Router Environmental Specifications

Table 15 on page 137 specifies the environmental specifications required for normal router
operation. In addition, the site should be as dust-free as possible.

Table 15: Router Environmental Specifications

Description Value

Altitude No performance degradation to 10,000 ft (3048 m)

Relative humidity Normal operation ensured in relative humidity range of 5% to 90%,

noncondensing

Temperature Normal operation ensured in temperature range of 32°F (0°C) to

104°F (40°C)

Nonoperating storage temperature in shipping container:

–40°F (–40°C) to 158°F (70°C)

Seismic Designed to meet Telcordia Technologies Zone 4 earthquake

requirements

Maximum thermal output AC power: 7161 BTU/hour (2100 W)

DC power: 5074 BTU/hour (1488 W)

NOTE: Install the router only in restricted areas, such as dedicated equipment rooms
and equipment closets, in accordance with Articles 110-16, 110-17, and 110-18 of the
National Electrical Code, ANSI/NFPA 70.

Related Topics • Routine Maintenance Procedures for the MX80 Router on page 61

• General Safety Guidelines for M Series, MX Series, and T Series Routers on page 101

Copyright © 2010, Juniper Networks, Inc. 137

MX80 3D Universal Edge Router Hardware Guide

• General Safety Warnings for M Series, MX Series, and T Series Routers on page 102

• Compliance Statements for Environmental Requirements for MX80 Routers

138 Copyright © 2010, Juniper Networks, Inc.

APPENDIX D

Power Guidelines, Requirements, and

Specifications for the MX80 Router

• MX80 Router Grounding Specifications on page 139

• MX80 Router AC Power Specifications and Requirements on page 141
• MX80 Router DC Power Specifications and Requirements on page 145
• Site Electrical Wiring Guidelines for M Series, MX Series, and T Series Routers on page 150

MX80 Router Grounding Specifications

• MX80 Chassis Grounding Points Specifications on page 139

• MX80 Router Grounding Cable Lug Specifications on page 140
• MX80 Router Grounding Cable Specifications on page 140

MX80 Chassis Grounding Points Specifications

To meet safety and electromagnetic interference (EMI) requirements and to ensure
proper operation, the router must be adequately grounded before power is connected.
To ground AC-powered and DC-powered routers, you must connect a grounding cable
to earth ground and then attach it to the chassis grounding points using the two screws
provided (see Figure 51 on page 140).

Two threaded holes are provided on the upper rear of the chassis for connecting the
router to earth ground. The grounding points fit SAE 10-32 screws (American). The
grounding points are spaced at 0.625-in. (15.86-mm) centers.

NOTE: Additional grounding is provided to an AC-powered router when you plug its
power supplies into grounded AC power receptacles.

Copyright © 2010, Juniper Networks, Inc. 139

MX80 3D Universal Edge Router Hardware Guide

Figure 51: Grounding Points on the MX80 Router

Protective
earthing terminal
(grounding points)

CLOCK

g005009
SYNC

MX80 Router Grounding Cable Lug Specifications

The accessory box shipped with the router includes one cable lug that attaches to the
grounding cable (see Figure 52 on page 140) and two SAE 10–32 screws used to secure
the grounding cable to the grounding points.

Figure 52: Grounding Cable Lug

1.69
End view

0.38 0.2 6 AWG conductor

dia.

g005042
0.06 0.625 All measurements in inches

CAUTION: Before router installation begins, a licensed electrician must attach a cable
lug to the grounding and power cables that you supply. A cable with an incorrectly
attached lug can damage the router.

MX80 Router Grounding Cable Specifications

You must provide one grounding cable that meets the following specifications: 6-AWG
2
(13.3 mm ), minimum 60°C wire, or as required by the local code.

Related Topics • Tools and Parts Required for MX80 Router Grounding and Power Connections on
page 45

• Preventing Electrostatic Discharge Damage to an MX80 Router on page 104

• MX80 Router AC Power Specifications on page 141

• MX80 Router DC Power Specifications on page 146

140 Copyright © 2010, Juniper Networks, Inc.

 Appendix D: Power Guidelines, Requirements, and Specifications for the MX80 Router

MX80 Router AC Power Specifications and Requirements

• MX80 Router AC Power Specifications on page 141

• Power Consumption for an AC-Powered MX80 Router on page 142
• AC Power Circuit Breaker Requirements for the MX80 Router on page 143
• AC Power Cord Specifications for the MX80 Router on page 143

MX80 Router AC Power Specifications

Table 16 on page 141 lists the AC power system electrical specifications.

Table 16: AC Power System Electrical Specifications

Item Specification

AC input voltage Operating range: 90 to 264 VAC

AC input line frequency 50 to 60 Hz (nominal)

AC system current rating 6 A @ 110 VAC (7 A maximum per inlet at 90 VAC) or 3 A @ 220 VAC

AC system input power 610 W

Table 17 on page 141 lists the AC power supply electrical specifications.

Table 17: AC Power Supply Electrical Specifications

Item Specification

Maximum output power 500 W

AC input voltage Operating range: 90 to 264 VAC (nominal)

AC input line frequency 50 to 60 Hz (nominal)

AC input current rating 6 A @ 110 VAC or 3 A @ 220 VAC maximum

Related Topics • MX80 Power System Description on page 16

• Maintaining the MX80 Power Supplies on page 65

• Replacing an MX80 AC Power Supply on page 85

• AC Power Cord Specifications for the MX80 Router on page 143

• AC Power Circuit Breaker Requirements for the MX80 Router on page 143

• AC Power Electrical Safety Guidelines and Warnings for MX80 Routers on page 124

Copyright © 2010, Juniper Networks, Inc. 141

MX80 3D Universal Edge Router Hardware Guide

Power Consumption for an AC-Powered MX80 Router

To allow for future growth so that you can operate the router in any hardware configuration
without upgrading the power infrastructure, we recommend that you provision
6 A @ 110 VAC (660 W) or 3 A @ 220 VAC (660 W) for each input.

Table 18 on page 142 and Table 19 on page 142 list the power requirements for base
AC-powered routers operating under typical voltage conditions.

If you do not plan to provision 6 A @ 110 VAC (660 W) or 3 A @ 220 VAC (660 W) for
each input, you can use the information in Table 18 on page 142, Table 19 on page 142, and
Table 20 on page 142 to calculate the power consumption and thermal output for your
hardware configuration.

Table 18: AC Base Router Power Requirements for the Fixed MX80 Router
Fixed Chassis Power Requirement (Watts)
Configuration Power Requirement (Watts) with 85% Efficiency

Chassis running at high 320 W 376 W

activity, with four 10-Gigabit
Ethernet XFPs, and fans
running at high speed

Table 19: AC Base Router Power Requirements for the Modular MX80
Router
Modular Chassis Power Requirement (Watts)
Configuration Power Requirement (Watts) with 85% Efficiency

Chassis running at high 310 W 365 W

activity, with four 10-Gigabit
Ethernet XFPs, two MICs,
and fans running at high
speed

Table 20 on page 142 lists the power requirements for various hardware components
when the router is operating under typical voltage conditions.

Table 20: Component Power Requirements

Power Power Requirement
Requirement (Watts) with 85%
Component (Watts) Efficiency

MIC (generalized value) 35 W 41 W

These examples use generalized values per MIC. For exact MIC power requirements, see
the MX Series 3D Universal Edge Routers Line Card Guide.

142 Copyright © 2010, Juniper Networks, Inc.

 Appendix D: Power Guidelines, Requirements, and Specifications for the MX80 Router

Typical power consumption for modular AC-powered routers @ 220 V (includes 85%
efficiency):

• Active AC-powered router with one MIC:

Base router (high activity, with four 10-Gigabit Ethernet XFPs, and fans running at high
speed) + 1 MIC =
282 W + 41 W = 323 W

• Active AC-powered router with two MICs:

Base router (high activity, with four 10-Gigabit Ethernet XFPs, and fans running at high
speed) + 2 MICs
282 W + 2(41 W)= 364 W

• Example of calculating system thermal output:

Watts AC PEM * 3.41 = BTU/hr

364 W * 3.41 = 1241 BTU/hr

Related Topics • MX80 Power System Description on page 16

• Maintaining the MX80 Power Supplies on page 65

• Replacing an MX80 AC Power Supply on page 85

• AC Power Electrical Safety Guidelines and Warnings for MX80 Routers on page 124

• AC Power Circuit Breaker Requirements for the MX80 Router on page 143

• AC Power Cord Specifications for the MX80 Router on page 143

AC Power Circuit Breaker Requirements for the MX80 Router

We recommend that you use a dedicated customer site circuit breaker rated for
15 A (110 VAC) minimum or 10 A (220 VAC) minimum for each AC power feed, or as
required by local code. Doing so enables you to operate the router in any configuration
without upgrading the power infrastructure.

Related Topics • MX80 Power System Description on page 16

• Maintaining the MX80 Power Supplies on page 65

• Replacing an MX80 AC Power Supply on page 85

• Power Consumption for an AC-Powered MX80 Router on page 142

• AC Power Electrical Safety Guidelines and Warnings for MX80 Routers on page 124

• AC Power Cord Specifications for the MX80 Router on page 143

AC Power Cord Specifications for the MX80 Router

Each AC power supply has a single AC appliance inlet located on the power supply that
requires a dedicated AC power feed. Most sites distribute power through a main conduit
that leads to frame-mounted power distribution panels, one of which can be located at
the top of the rack that houses the router. An AC power cord connects each power supply
to the power distribution panel.

Copyright © 2010, Juniper Networks, Inc. 143

MX80 3D Universal Edge Router Hardware Guide

You can order detachable AC power cords, each approximately 8 ft (2.5 m) long that
supply AC power to the router. The C19 appliance coupler at the female end of the cord
inserts into the AC appliance inlet coupler, type C20 (right angle) as described by
International Electrotechnical Commission (IEC) standard 60320. The plug at the male
end of the power cord fits into the power source receptacle that is standard for your
geographical location.

Table 21 on page 144 provides specifications and Figure 53 on page 144 depicts the plug
on the AC power cord provided for each country or region.

Table 21: AC Power Cord Specifications

Country Model Number Electrical Specification Plug Type

Australia CBL-JX-PWR-AU 250 VAC, 10 A, 50 Hz AS/NZ 3112–1993

China CBL-JX-PWR-CH 250 VAC, 10 A, 50 Hz GB2099.1 1996 and GB1002

1996 (CH1-10P)

Europe (except Italy and CBL-JX-PWR-EU 250 VAC, 10 A, 50 Hz CEE (7) VII
United Kingdom)

Italy CBL-JX-PWR-IT 250 VAC, 10 A, 50 Hz CEI 23–16/VII

Japan CBL-JX-PWR-JP 125 VAC, 12 A, 50 Hz or 60 Hz JIS 8303

North America CBL-JX-PWR-US 125 VAC, 10 A, 60 Hz NEMA 5-15

United Kingdom CBL-JX-PWR-UK 250 VAC, 10 A, 50 Hz BS 1363A

Figure 53: AC Plug Types

WARNING: The AC power cord for the router is intended for use with the router only
and not for any other use.

144 Copyright © 2010, Juniper Networks, Inc.

 Appendix D: Power Guidelines, Requirements, and Specifications for the MX80 Router

WARNING: The attached power cable is only for this product. Do not use the cable for
another product. Translation in Japanese follows:

NOTE: In North America, AC power cords must not exceed approximately 14.75 ft (4.5 m)
in length, to comply with National Electrical Code (NEC) Sections 400-8 (NFPA 75,
5-2.2) and 210-52, and Canadian Electrical Code (CEC) Section 4-010(3). You can order
AC power cords that are in compliance.

WARNING: The router is pluggable type A equipment installed in a restricted-access

location. It has a separate protective earthing terminal (sized for SAE 10-32 ground
screws) provided on the chassis in addition to the grounding pin of the power supply
cord. This separate protective earthing terminal must be permanently connected to
earth.

CAUTION: Power cords and cables must not block access to device components or
drape where people could trip on them.

Related Topics • MX80 Power System Description on page 16

• Maintaining the MX80 Power Supplies on page 65

• Replacing an MX80 AC Power Supply on page 85

• AC Power Electrical Safety Guidelines and Warnings for MX80 Routers on page 124

• Power Consumption for an AC-Powered MX80 Router on page 142

• AC Power Circuit Breaker Requirements for the MX80 Router on page 143

MX80 Router DC Power Specifications and Requirements

• MX80 Router DC Power Specifications on page 146

• Power Consumption for a DC-Powered MX80 Router on page 146
• DC Power Circuit Breaker Requirements for the MX80 Router on page 148
• DC Power Source Cabling for the MX80 Router on page 149
• DC Power Cable Specifications for the MX80 Router on page 149

Copyright © 2010, Juniper Networks, Inc. 145

MX80 3D Universal Edge Router Hardware Guide

MX80 Router DC Power Specifications

Table 22 on page 146 lists the DC power system electrical specifications.

Table 22: DC Power System Electrical Specifications

Item Specification

DC input voltage Operating range: –40 to –72 VDC

DC system input current 13 A @ –48 VDC (maximum) (625 W DC)

rating

DC system input power 13 A @ –48 VDC (625 W DC)

Table 23 on page 146 lists the DC power supply electrical specifications.

Table 23: DC Power Supply Electrical Specifications

Item Specification

Maximum output power 500 W

DC input voltage Minimum: –40 VDC

Nominal: –48 VDC, –60 VDC

Operating range: –40 to –72 VDC

DC input current rating 13 A @ –48 VDC

Related Topics • MX80 Power System Description on page 16

• Maintaining the MX80 Power Supplies on page 65

• Replacing an MX80 DC Power Supply on page 88

• MX80 DC Power Electrical Safety Guidelines on page 125

• Power Consumption for a DC-Powered MX80 Router on page 146

• DC Power Circuit Breaker Requirements for the MX80 Router on page 148

• DC Power Source Cabling for the MX80 Router on page 149

• DC Power Cable Specifications for the MX80 Router on page 149

Power Consumption for a DC-Powered MX80 Router

To allow for future growth so that you can operate the router in any hardware configuration
without upgrading the power infrastructure, we recommend that you provision at least
25 A @ –48 VDC for each input.

Table 24 on page 147 and Table 25 on page 147 list the power requirements for base
DC-powered routers operating under typical voltage conditions.

146 Copyright © 2010, Juniper Networks, Inc.

 Appendix D: Power Guidelines, Requirements, and Specifications for the MX80 Router

If you do not plan to provision at least 25 A @ –48 VDC per input, you can use the
information in Table 24 on page 147, Table 25 on page 147, and Table 26 on page 147 to
calculate the power consumption @ –48 VDC and thermal output for your hardware
configuration.

Table 24: DC-Powered Base Router Power Requirements for the Fixed
MX80 Router
Current
Power Requirement
Requirement (Amps @
Fixed Chassis Configuration (Watts) –48 VDC)

Chassis running at high activity, with four 10-Gigabit 320 W 6.7 A

Ethernet XFPs, and fans running at high speed (approximate)

Table 25: DC-Powered Base Router Power Requirements for the Modular
MX80 Router
Current
Power Requirement
Requirement (Amps @
Modular Chassis Configuration (Watts) –48 VDC)

Chassis running at high activity, with four 10-Gigabit 310 W 6.5 A

Ethernet XFPs, two MICs, and fans running at high speed (approximate)

Table 26 on page 147 lists the power requirements for various hardware components
when the router is operating under typical voltage conditions.

Table 26: Component Power Requirements for DC-Powered Routers

Current
Requirement
Power Requirement (Amps @
Component (Watts) –48 VDC)

MIC (generalized value) 35 W 0.73 A

These examples show how to calculate typical power consumption for your DC-powered
router configuration. The examples use generalized values for MICs. For exact MIC power
requirements, see the MX Series 3D Universal Edge Routers Line Card Guide.

Typical power consumption for modular DC-powered routers:

• Active DC-powered router with one MIC:

Base router (high activity, with four 10-Gigabit Ethernet XFPs, and fans running at high
speed) + 1 MIC =
5 A + 0.73 A = 5.73 A @ –48 VDC = 275 W DC

• Active DC-powered router with two MICs:

Base router (high activity, with four 10-Gigabit Ethernet XFPs, and fans running at high
speed) + 2 MICs

Copyright © 2010, Juniper Networks, Inc. 147

MX80 3D Universal Edge Router Hardware Guide

5 A + 2(0.73 A) = 6.46 A @ –48 VDC = 310 W DC

• Input current from a DC source other than –48 VDC (based on maximum configuration;
applies to DC power supply only):

(–54 VDC input) * (input current X) = (–48 VDC input) * (input current Y)
54 * X = 48 * 25 A
X = 48 * 25 A/54 = 22.2 A

• Example of calculating system thermal output:

Watts DC * 3.41 = BTU/hr

310 * 3.41 = 1,057 BTU/hr

Related Topics • MX80 Power System Description on page 16

• Maintaining the MX80 Power Supplies on page 65

• Replacing an MX80 DC Power Supply on page 88

• MX80 DC Power Electrical Safety Guidelines on page 125

• MX80 Router DC Power Specifications on page 146

• DC Power Circuit Breaker Requirements for the MX80 Router on page 148

• DC Power Source Cabling for the MX80 Router on page 149

• DC Power Cable Specifications for the MX80 Router on page 149

DC Power Circuit Breaker Requirements for the MX80 Router

Each DC power supply has a single DC input (–48 VDC and return) that requires a
dedicated circuit breaker. We recommend that you use a dedicated customer site circuit
breaker rated for 25 A (–48 VDC) minimum, or as required by local code. Doing so enables
you to operate the router in any configuration without upgrading the power infrastructure.

If you plan to operate a DC-powered router at less than the maximum configuration and
do not provision a 25 A (–48 VDC) circuit breaker, we recommend that you provision a
dedicated customer site circuit breaker for each DC power supply rated for at least 125
percent of the continuous current that the system draws at –48 VDC.

Related Topics • MX80 Power System Description on page 16

• Maintaining the MX80 Power Supplies on page 65

• Replacing an MX80 DC Power Supply on page 88

• MX80 DC Power Electrical Safety Guidelines on page 125

• MX80 Router DC Power Specifications on page 146

• Power Consumption for a DC-Powered MX80 Router on page 146

• DC Power Source Cabling for the MX80 Router on page 149

• DC Power Cable Specifications for the MX80 Router on page 149

148 Copyright © 2010, Juniper Networks, Inc.

 Appendix D: Power Guidelines, Requirements, and Specifications for the MX80 Router

DC Power Source Cabling for the MX80 Router

The DC power supply in PS0 must be powered by a dedicated power feed derived from
feed A, and the DC power supply in PS1 must be powered by a dedicated power feed
derived from feed B. This configuration provides the commonly deployed A/B feed
redundancy for the system.

CAUTION: You must ensure that power connections maintain the proper polarity. The
power source cables might be labeled (+) and (–) to indicate their polarity. There is no
standard color coding for DC power cables. The color coding used by the external DC
power source at your site determines the color coding for the leads on the power cables
that attach to the terminal studs on each power supply.

WARNING: For field-wiring connections, use copper conductors only.

CAUTION: Power cords and cables must not block access to device components or
drape where people could trip on them.

Related Topics • MX80 Power System Description on page 16

• Maintaining the MX80 Power Supplies on page 65

• Replacing an MX80 DC Power Supply on page 88

• MX80 DC Power Electrical Safety Guidelines on page 125

• MX80 Router DC Power Specifications on page 146

• Power Consumption for a DC-Powered MX80 Router on page 146

• DC Power Circuit Breaker Requirements for the MX80 Router on page 148

• DC Power Cable Specifications for the MX80 Router on page 149

DC Power Cable Specifications for the MX80 Router

• DC Power Cable Lug Specifications on page 149
• DC Power Cable Specifications on page 150

DC Power Cable Lug Specifications

The accessory box shipped with the router includes the cable lugs that attach to the
terminal of each power supply (see Figure 54 on page 150).

Copyright © 2010, Juniper Networks, Inc. 149

MX80 3D Universal Edge Router Hardware Guide

Figure 54: DC Power Cable Lug

0.76

0.25
.170 max.
wire dia.
(insul.)
.15 dia. 0.63

g005043
All measurements in inches

CAUTION: Before router installation begins, a licensed electrician must attach a cable
lug to the grounding and power cables that you supply. A cable with an incorrectly
attached lug can damage the router.

DC Power Cable Specifications

You must supply four DC power cables that meet the following specifications: 16-AWG
2
(1.3 mm ), minimum 60° C wire, or as required by the local code.

Related Topics • MX80 Power System Description on page 16

• Maintaining the MX80 Power Supplies on page 65

• Replacing an MX80 DC Power Supply on page 88

• MX80 DC Power Electrical Safety Guidelines on page 125

• MX80 Router DC Power Specifications on page 146

• Power Consumption for a DC-Powered MX80 Router on page 146

• DC Power Circuit Breaker Requirements for the MX80 Router on page 148

• DC Power Source Cabling for the MX80 Router on page 149

Site Electrical Wiring Guidelines for M Series, MX Series, and T Series Routers

• Distance Limitations for Signaling on page 150

• Radio Frequency Interference on page 151
• Electromagnetic Compatibility on page 151

Distance Limitations for Signaling

Improperly installed wires can emit radio interference. In addition, the potential for damage
from lightning strikes increases if wires exceed recommended distances or if wires pass
between buildings. The electromagnetic pulse (EMP) caused by lightning can damage
unshielded conductors and destroy electronic devices. If your site has previously
experienced such problems, you might want to consult experts in electrical surge
suppression and shielding.

150 Copyright © 2010, Juniper Networks, Inc.

 Appendix D: Power Guidelines, Requirements, and Specifications for the MX80 Router

Radio Frequency Interference

You can reduce or eliminate the emission of radio frequency interference (RFI) from your
site wiring by using twisted-pair cable with a good distribution of grounding conductors.
If you must exceed the recommended distances, use a high-quality twisted-pair cable
with one ground conductor for each data signal when applicable.

Electromagnetic Compatibility
If your site is susceptible to problems with electromagnetic compatibility (EMC),
particularly from lightning or radio transmitters, you might want to seek expert advice.
Strong sources of electromagnetic interference (EMI) can destroy the signal drivers and
receivers in the router and conduct power surges over the lines into the equipment,
resulting in an electrical hazard. It is particularly important to provide a properly grounded
and shielded environment and to use electrical surge-suppression devices.

CAUTION: To comply with intrabuilding lightning and surge requirements, intrabuilding

wiring must be shielded, and the shield for the wiring must be grounded at both ends.

WARNING: The intrabuilding port(s) of the equipment or subassembly is suitable for

connection to intrabuilding or unexposed wiring or cabling only. The intrabuilding port(s)
of the equipment or subassembly MUST NOT be metallically connected to interfaces
that connect to the OSP or its wiring. These interfaces are designed for use as
intrabuilding interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE,
Issue 4) and require isolation from the exposed OSP cabling. The addition of primary
protectors is not sufficient protection in order to connect these interfaces metallically
to OSP wiring.

Related Topics • Compliance Statements for EMC Requirements for M Series, MX Series, and T Series
Routers (United States)

• Compliance Statements for EMC Requirements for M Series, MX Series, and T Series
Routers (Japan)

• Compliance Statements for EMC Requirements for M Series, MX Series, and T Series
Routers (Canada)

Copyright © 2010, Juniper Networks, Inc. 151

MX80 3D Universal Edge Router Hardware Guide

152 Copyright © 2010, Juniper Networks, Inc.

APPENDIX E

Cable and Wire Guidelines and

Specifications for the MX80 Router

• Understanding Fiber-Optic Cable Signal Loss, Attenuation, and Dispersion on page 153
• Calculating Power Budget and Power Margin for Fiber-Optic Cables on page 154
• Routing Engine Interface Cable Specifications for MX80 Routers on page 156

Understanding Fiber-Optic Cable Signal Loss, Attenuation, and Dispersion

• Signal Loss in Multimode and Single-Mode Fiber-Optic Cable on page 153

• Attenuation and Dispersion in Fiber-Optic Cable on page 153

Signal Loss in Multimode and Single-Mode Fiber-Optic Cable

Multimode fiber is large enough in diameter to allow rays of light to reflect internally
(bounce off the walls of the fiber). Interfaces with multimode optics typically use LEDs
as light sources. LEDs are not coherent sources, however. They spray varying wavelengths
of light into the multimode fiber, which reflects the light at different angles. Light rays
travel in jagged lines through a multimode fiber, causing signal dispersion. When light
traveling in the fiber core radiates into the fiber cladding, higher-order mode loss (HOL)
results. Together these factors limit the transmission distance of multimode fiber
compared to single-mode fiber.

Single-mode fiber is so small in diameter that rays of light can reflect internally through
one layer only. Interfaces with single-mode optics use lasers as light sources. Lasers
generate a single wavelength of light, which travels in a straight line through the
single-mode fiber. Compared with multimode fiber, single-mode fiber has higher
bandwidth and can carry signals for longer distances. It is consequently more expensive.

Exceeding the maximum transmission distances can result in significant signal loss, which
causes unreliable transmission.

Attenuation and Dispersion in Fiber-Optic Cable

Correct functioning of an optical data link depends on modulated light reaching the
receiver with enough power to be demodulated correctly. Attenuation is the reduction
in power of the light signal as it is transmitted. Attenuation is caused by passive media
components, such as cables, cable splices, and connectors. While attenuation is
significantly lower for optical fiber than for other media, it still occurs in both multimode

Copyright © 2010, Juniper Networks, Inc. 153

MX80 3D Universal Edge Router Hardware Guide

and single-mode transmission. An efficient optical data link must have enough light
available to overcome attenuation.

Dispersion is the spreading of the signal in time. The following two types of dispersion
can affect an optical data link:

• Chromatic dispersion—Spreading of the signal in time resulting from the different

speeds of light rays.

• Modal dispersion—Spreading of the signal in time resulting from the different

propagation modes in the fiber.

For multimode transmission, modal dispersion, rather than chromatic dispersion or

attenuation, usually limits the maximum bit rate and link length. For single-mode
transmission, modal dispersion is not a factor. However, at higher bit rates and over longer
distances, chromatic dispersion rather than modal dispersion limits maximum link length.

An efficient optical data link must have enough light to exceed the minimum power that
the receiver requires to operate within its specifications. In addition, the total dispersion
must be less than the limits specified for the type of link in Telcordia Technologies
document GR-253-CORE (Section 4.3) and International Telecommunications Union
(ITU) document G.957.

When chromatic dispersion is at the maximum allowed, its effect can be considered as
a power penalty in the power budget. The optical power budget must allow for the sum
of component attenuation, power penalties (including those from dispersion), and a
safety margin for unexpected losses.

Calculating Power Budget and Power Margin for Fiber-Optic Cables

• Calculating Power Budget for Fiber-Optic Cable on page 154

• Calculating Power Margin for Fiber-Optic Cable on page 155

Calculating Power Budget for Fiber-Optic Cable

To ensure that fiber-optic connections have sufficient power for correct operation, you
need to calculate the link's power budget, which is the maximum amount of power it
can transmit. When you calculate the power budget, you use a worst-case analysis to
provide a margin of error, even though all the parts of an actual system do not operate
at the worst-case levels. To calculate the worst-case estimate of power budget (P ),
B

you assume minimum transmitter power (P ) and minimum receiver sensitivity (P ):

T R

P =P –P
B T R

The following hypothetical power budget equation uses values measured in decibels
(dB) and decibels referred to one milliwatt (dBm):

P =P –P
B T R

P = –15 dBm – (–28 dBm)

B

P = 13 dB
B

154 Copyright © 2010, Juniper Networks, Inc.

 Appendix E: Cable and Wire Guidelines and Specifications for the MX80 Router

Calculating Power Margin for Fiber-Optic Cable

After calculating a link's power budget you can calculate the power margin (P ), which
M

represents the amount of power available after subtracting attenuation or link loss (LL)
from the power budget (P ). A worst-case estimate of P assumes maximum LL:
B M

P = P – LL
M B

A P greater than zero indicates that the power budget is sufficient to operate the receiver.
M

Factors that can cause link loss include higher-order mode losses (HOL), modal and
chromatic dispersion, connectors, splices, and fiber attenuation. Table 27 on page 155
lists an estimated amount of loss for the factors used in the following sample calculations.
For information about the actual amount of signal loss caused by equipment and other
factors, refer to vendor documentation.

Table 27: Estimated Values for Factors Causing Link Loss

Link-Loss Factor Estimated Link-Loss Value

Higher-order mode losses Single-mode—None

Multimode—0.5 dB

Modal and chromatic dispersion Single-mode—None

Multimode—None, if product of bandwidth and distance

is less than 500 MHz-km

Connector 0.5 dB

Splice 0.5 dB

Fiber attenuation Single-mode—0.5 dB/km

Multimode—1 dB/km

The following example uses the estimated values in Table 27 on page 155 to calculate
link loss (LL) for a 2-km-long multimode link with a power budget (P ) of 13 dB:
B

• Fiber attenuation for 2 km @ 1.0 dB/km= 2 dB

• Loss for five connectors @ 0.5 dB per connector = 5(0.5 dB) = 2.5 dB

• Loss for two splices @ 0.5 dB per splice =2(0.5 dB) = 1 dB

• Higher-order mode loss = 0.5 dB

• Clock recovery module = 1 dB

The power margin (P ) is calculated as follows:

M

P = P – LL
M B

Copyright © 2010, Juniper Networks, Inc. 155

MX80 3D Universal Edge Router Hardware Guide

P = 13 dB – 2 km (1.0 dB/km) – 5 (0.5 dB) – 2 (0.5 dB) – 0.5 dB [HOL] – 1 dB [CRM]

M

P = 13 dB – 2 dB – 2.5 dB – 1 dB – 0.5 dB – 1 dB
M

P = 6 dB
M

The following sample calculation for an 8-km-long single-mode link with a power budget
(P ) of 13 dB uses the estimated values from Table 27 on page 155 to calculate link loss
B

(LL) as the sum of fiber attenuation (8 km @ 0.5 dB/km, or 4 dB) and loss for seven
connectors (0.5 dB per connector, or 3.5 dB). The power margin (P ) is calculated as
M

follows:

P = P – LL
M B

P = 13 dB – 8 km (0.5 dB/km) – 7(0.5 dB)

M

P = 13 dB – 4 dB – 3.5 dB
M

P = 5.5 dB
M

In both examples, the calculated power margin is greater than zero, indicating that the
link has sufficient power for transmission and does not exceed the maximum receiver
input power.

Routing Engine Interface Cable Specifications for MX80 Routers

Table 28 on page 156 lists the specifications for the cables that connect to management
ports and the wires that connect to the alarm relay contacts.

Table 28: Cable Specifications for Routing Engine Management

Cable Cable/Wire Maximum Router
Port Specification Supplied Length Receptacle

Routing Engine RS-232 One 6-ft 6 ft (1.83 m) RJ-45 female

console or (EIA-232) serial (1.83-m) length
auxiliary cable with RJ-45/DB-9
interface connectors

Routing Engine Category 5 cable One 15-ft 328 ft (100 m) RJ-45

Ethernet or equivalent (4.57-m) length autosensing
interface suitable for with
100Base-T RJ-45/RJ-45
operation connectors

Related Topics • MX80 Routing Engine Description on page 19

• Maintaining the MX80 Routing Engine on page 66

• RJ-45 Connector Pinouts for the ETHERNET Port on the MX80 Router on page 157

• RJ-45 Connector Pinouts for the AUX and CONSOLE Ports on the MX80 Router on
page 158

156 Copyright © 2010, Juniper Networks, Inc.

APPENDIX F

MX80 Cable Connector Pinouts

• RJ-45 Connector Pinouts for the ETHERNET Port on the MX80 Router on page 157
• RJ-45 Connector Pinouts for the AUX and CONSOLE Ports on the MX80
Router on page 158

RJ-45 Connector Pinouts for the ETHERNET Port on the MX80 Router

The port on the front panel labeled ETHERNET is an autosensing 10/100-Mbps Ethernet
RJ-45 receptacle that accepts an Ethernet cable for connecting the Routing Engine to a
management LAN (or other device that supports out-of-band management). Table 29
on page 157 describes the RJ-45 connector pinout.

Table 29: RJ-45 Connector Pinout for the Routing Engine ETHERNET Port
Pin Signal

1 TX+

2 TX–

3 RX+

4 Termination network

5 Termination network

6 RX–

7 Termination network

8 Termination network

Related Topics • MX80 Routing Engine Description on page 19

• Maintaining the MX80 Routing Engine on page 66

• Routing Engine Interface Cable Specifications for MX80 Routers on page 156

• RJ-45 Connector Pinouts for the AUX and CONSOLE Ports on the MX80 Router on
page 158

Copyright © 2010, Juniper Networks, Inc. 157

MX80 3D Universal Edge Router Hardware Guide

RJ-45 Connector Pinouts for the AUX and CONSOLE Ports on the MX80 Router

The ports on the front panel labeled AUX and CONSOLE are asynchronous serial interfaces
that accept an RJ-45 connector. The ports connect the Routing Engine to an auxiliary or
console management device. Table 30 on page 158 describes the RJ-45 connector pinout.

Table 30: RJ-45 Connector Pinout for the AUX and CONSOLE Ports
Pin Signal Description

1 RTS Request to Send

2 DTR Data Terminal Ready

3 TXD Transmit Data

4 Ground Signal Ground

5 Ground Signal Ground

6 RXD Receive Data

7 DSR/DCD Data Set Ready

8 CTS Clear to Send

Related Topics • MX80 Routing Engine Description on page 19

• Maintaining the MX80 Routing Engine on page 66

• Routing Engine Interface Cable Specifications for MX80 Routers on page 156

• RJ-45 Connector Pinouts for the ETHERNET Port on the MX80 Router on page 157

158 Copyright © 2010, Juniper Networks, Inc.

APPENDIX G

Contacting Customer Support and

Returning MX80 Hardware

• Locating MX80 Component Serial Numbers on page 159

• Contacting Customer Support on page 164
• Returning a Hardware Component to Juniper Networks, Inc. on page 164
• Packing the MX80 Router for Shipment on page 165
• Guidelines for Packing Router Components for Shipment on page 166

Locating MX80 Component Serial Numbers

• Displaying MX80 Components and Serial Numbers on page 159

• MX80 Chassis Serial Number Label on page 160
• MX80 Fan Tray Serial Number Label on page 161
• MX80 MIC Serial Number Label on page 162
• MX80 Power Supply Serial Number Label on page 163

Displaying MX80 Components and Serial Numbers

Before contacting Juniper Networks, Inc. to request a Return Materials Authorization
(RMA), you must find the serial number on the router or component. To display all of the
router components and their serial numbers, enter the following command-line interface
(CLI) command:
user@host> show chassis hardware
Hardware inventory:
Item Version Part number Serial number Description
Chassis MX80
Midplane REV 01 711-031594 JR6922 MX80
Routing Engine BUILTIN BUILTIN Routing Engine
TFEB 0 BUILTIN BUILTIN Forwarding Engine
Processor
QXM 0 REV 05 711-028408 JR6848 MPC QXM
FPC 0 BUILTIN BUILTIN MPC BUILTIN
MIC 0 BUILTIN BUILTIN 4x 10GE XFP
PIC 0 BUILTIN BUILTIN 4x 10GE XFP
Xcvr 0 REV 01 740-014289 AD0932M007L XFP-10G-SR
Xcvr 1 REV 01 740-014289 AD0932M009M XFP-10G-SR
Xcvr 2 REV 01 740-014289 AD0932M005N XFP-10G-SR
Xcvr 3 REV 01 740-014279 K9J02T2 XFP-10G-LR

Copyright © 2010, Juniper Networks, Inc. 159

MX80 3D Universal Edge Router Hardware Guide

MIC 1 REV 02 750-028380 JR6552 3D 2x 10GE XFP

PIC 2 BUILTIN BUILTIN 1x 10GE XFP
Xcvr 0 REV 01 740-014289 98S803A90363 XFP-10G-SR
PIC 3 BUILTIN BUILTIN 1x 10GE XFP
Xcvr 0 REV 01 740-014289 98S803A90259 XFP-10G-SR
FPC 1 BUILTIN BUILTIN MPC BUILTIN
MIC 0 REV 02 750-028380 JG8544 3D 2x 10GE XFP
PIC 0 BUILTIN BUILTIN 1x 10GE XFP
Xcvr 0 REV 01 740-014289 98S803A90421 XFP-10G-SR
PIC 1 BUILTIN BUILTIN 1x 10GE XFP
Xcvr 0 REV 01 740-014289 98S803A90260 XFP-10G-SR
MIC 1 REV 02 750-028380 JR6544 3D 2x 10GE XFP
PIC 2 BUILTIN BUILTIN 1x 10GE XFP
Xcvr 0 REV 01 740-014279 K9J03BF XFP-10G-LR
PIC 3 BUILTIN BUILTIN 1x 10GE XFP
Xcvr 0 REV 01 740-014279 K9J02UB XFP-10G-LR
Fan Tray Fan Tray
Most components also have a small rectangular serial number ID label (see Figure 55
on page 160) attached to the component body.

Figure 55: Serial Number ID Label

Related Topics • MX80 Chassis Serial Number Label on page 160

• MX80 Fan Tray Serial Number Label on page 161

• MX80 MIC Serial Number Label on page 162

• MX80 Power Supply Serial Number Label on page 163

• Contacting Customer Support on page 164

• Returning a Hardware Component to Juniper Networks, Inc. on page 164

MX80 Chassis Serial Number Label

The chassis serial number is located on the rear of the chassis (see Figure 56 on page 160).

Figure 56: MX80 Chassis Serial Number Label

CLOCK
g005021

SYNC

Serial number
ID label

Related Topics • MX80 Chassis Description on page 5

• Displaying MX80 Components and Serial Numbers on page 159

160 Copyright © 2010, Juniper Networks, Inc.

 Appendix G: Contacting Customer Support and Returning MX80 Hardware

• Contacting Customer Support on page 164

• Returning a Hardware Component to Juniper Networks, Inc. on page 164

MX80 Fan Tray Serial Number Label

The serial number label is located on the top of the fan tray toward the front (see Figure
57 on page 161).

Figure 57: MX80 Fan Tray Serial Number Label

Serial number ID label

Related Topics • MX80 Cooling System Description on page 8 g005045

• Maintaining the MX80 Fan Tray on page 62

• Troubleshooting the MX80 Fan Tray on page 69

• Replacing an MX80 Fan Tray on page 75

• Displaying MX80 Components and Serial Numbers on page 159

• Contacting Customer Support on page 164

• Returning a Hardware Component to Juniper Networks, Inc. on page 164

Copyright © 2010, Juniper Networks, Inc. 161

MX80 3D Universal Edge Router Hardware Guide

MX80 MIC Serial Number Label

The exact location may be slightly different on different MICs, depending on the placement
of components on the MIC board (see Figure 58 on page 162, Figure 59 on page 162, and
Figure 60 on page 163).

Figure 58: 20-Port MIC Figure 59: 40-Port MIC

Serial Number Label Serial Number Label

Serial
number
ID label

g004932

g004933
Serial number
ID label

162 Copyright © 2010, Juniper Networks, Inc.

 Appendix G: Contacting Customer Support and Returning MX80 Hardware

Figure 60: 2-Port MIC Serial Number Label

g004931
Serial number
ID label

Related Topics • MX80 Modular Interface Card Description on page 13

• Maintaining the MX80 MICs on page 63

• Troubleshooting the MX80 MICs on page 70

• Replacing an MX80 MIC on page 76

• Displaying MX80 Components and Serial Numbers on page 159

• Contacting Customer Support on page 164

• Returning a Hardware Component to Juniper Networks, Inc. on page 164

MX80 Power Supply Serial Number Label

The serial number label is located on the top of the power supply (see Figure 61 on
page 163).

Figure 61: Power Supply Serial Number Label

Serial number ID label
g005024

Copyright © 2010, Juniper Networks, Inc. 163

MX80 3D Universal Edge Router Hardware Guide

Related Topics • MX80 Power System Description on page 16

• Maintaining the MX80 Power Supplies on page 65

• Troubleshooting the MX80 Power Supplies on page 70

• Replacing an MX80 AC Power Supply on page 85

• Replacing an MX80 DC Power Supply on page 88

• Displaying MX80 Components and Serial Numbers on page 159

• Contacting Customer Support on page 164

• Returning a Hardware Component to Juniper Networks, Inc. on page 164

Contacting Customer Support

You can contact Juniper Networks Technical Assistance Center (JTAC) 24 hours a day,
7 days a week in one of the following ways:

• On the Web, using the Case Manager link at:

http://www.juniper.net/support/

• By telephone:

From the US and Canada: 1-888-314-JTAC

From all other locations: 1-408-745-9500

If contacting JTAC by phone, enter your 11-digit case number followed by the # key if
this is an existing case, or press the * key to be routed to the next available support
engineer.

When requesting support from JTAC by telephone, be prepared to provide the following
information:

• Your existing case number, if you have one

• Details of the failure or problem

• Type of activity being performed on the router when the problem occurred

• Configuration data using one or more of the show commands

Related Topics • Returning a Hardware Component to Juniper Networks, Inc. on page 164

Returning a Hardware Component to Juniper Networks, Inc.

If a problem cannot be resolved by the JTAC technician, a Return Materials Authorization

(RMA) is issued. This number is used to track the returned material at the factory and to
return repaired or new components to the customer as needed.

164 Copyright © 2010, Juniper Networks, Inc.

 Appendix G: Contacting Customer Support and Returning MX80 Hardware

NOTE: Do not return any component to Juniper Networks, Inc. unless you have first
obtained an RMA number. Juniper Networks, Inc. reserves the right to refuse shipments
that do not have an RMA. Refused shipments will be returned to the customer via collect
freight.

For more information about return and repair policies, see the customer support Web
page at http://www.juniper.net/support/guidelines.html.

For product problems or technical support issues, contact the Juniper Networks Technical
Assistance Center (JTAC) using the Case Manager link at http://www.juniper.net/support/
or at 1-888-314-JTAC (within the United States) or 1-408-745-9500 (from outside the
United States).

To return a hardware component:

1. Determine the part number and serial number of the component.

2. Obtain an RMA number from the Juniper Networks Technical Assistance Center
(JTAC). You can send e-mail or telephone as described above.

3. Provide the following information in your e-mail message or during the telephone
call:

• Part number and serial number of component

• Your name, organization name, telephone number, and fax number

• Description of the failure

4. The support representative validates your request and issues an RMA number for
return of the component.

5. Pack the router or component for shipment.

Related Topics • Contacting Customer Support on page 164

Packing the MX80 Router for Shipment

To pack the router for shipment:

1. Retrieve the shipping box and packing materials in which the router was originally
shipped. If you do not have these materials, contact your Juniper Networks
representative about approved packaging materials.

2. On the console or other management device connected to the Routing Engine, enter
CLI operational mode and issue the following command to shut down the router
software.
user@host> request system halt

Wait until a message appears on the console confirming that the operating system
has halted.

Copyright © 2010, Juniper Networks, Inc. 165

MX80 3D Universal Edge Router Hardware Guide

For more information about the command, see the Junos System Basics and Services
Command Reference.

3. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and
connect the strap to one of the ESD points on the chassis.

4. Shut down power to the router by pressing the AC input switch or DC circuit breaker
for all power supplies to the off (O) position.

5. Disconnect power from the router.

6. Remove the cables that connect to all external devices.

7. Remove all field replaceable units (FRUs) from the router.

8. Remove the router from the rack. One person should grasp the router while a second
person unscrews and removes the mounting screws from the rack. One lifter can
then move the router to the shipping container.

9. Place the router in the shipping container.

10. Cover the router with an ESD bag and place the packing foam on top of and around
the router.

11. Replace the accessory box on top of the packing foam.

12. Securely tape the box closed.

13. Write the RMA number on the exterior of the box to ensure proper tracking.

Related Topics • Returning a Hardware Component to Juniper Networks, Inc. on page 164

• Contacting Customer Support on page 164

Guidelines for Packing Router Components for Shipment

To pack and ship individual components:

• When you return components, make sure they are adequately protected with packing
materials and packed so that the pieces are prevented from moving around inside the
carton.

• Use the original shipping materials if they are available.

• Place individual boards in electrostatic bags.

• Write the RMA number on the exterior of the box to ensure proper tracking.

CAUTION: Do not stack any of the router components.

Related Topics • Returning a Hardware Component to Juniper Networks, Inc. on page 164

• Contacting Customer Support on page 164

166 Copyright © 2010, Juniper Networks, Inc.

PART 5

Index
• Index on page 169

Copyright © 2010, Juniper Networks, Inc. 167

MX80 3D Universal Edge Router Hardware Guide

168 Copyright © 2010, Juniper Networks, Inc.

Index
airflow
Symbols required clearance around chassis for...................26
#, comments in configuration statements...................xix alarm panel
( ), in syntax descriptions....................................................xix routine inspection of......................................................61
10-Gigabit Ethernet MIC (built-in) alarms............................................................................................11
description.........................................................................13 LEDs (red and yellow) on front panel......................11
< >, in syntax descriptions...................................................xix messages, list of.............................................................67
[ ], in configuration statements........................................xix temperature, displaying..............................................69
{ }, in configuration statements........................................xix altitude, acceptable range.................................................137
| (pipe), in syntax descriptions..........................................xix antistatic mat, using............................................................104
approvals, agency.................................................................129
A ATM analyzer, use of..............................................................64
AC plug types..........................................................................143 attenuation in fiber-optic cable.......................................153
AC power auxiliary port (for Routing Engine management)
connecting........................................................................47 cable
consumption..................................................................142 connection during initial installation.............42
provisioning.....................................................................142 connector pinouts (DB-9)...............................158
AC power circuit breaker.....................................................143 specifications........................................................156
AC power supply
cord See AC power supply cord B
electrical specifications..............................................141 base board
installing............................................................................86 description..........................................................................6
removing...........................................................................85 battery
replacing............................................................................85 environmental compliance.......................................133
AC power supply cord lithium...............................................................................133
connecting.......................................................................88 booting the router
disconnecting..................................................................87 AC-powered.....................................................................47
replacing............................................................................87 DC-powered......................................................................51
specifications.................................................................143 braces, in configuration statements................................xix
AC specifications brackets
electrical...........................................................................141 angle, in syntax descriptions.....................................xix
accessory box square, in configuration statements.......................xix
parts list.............................................................................32 built-in MICs
agency approvals..................................................................129 10-Gigabit Ethernet MIC, description......................13
air filter Tri-Rate MIC, description..............................................14
description..........................................................................8
installing.............................................................................74 C
maintaining......................................................................62 cabinet mounting
removing............................................................................73 requirements....................................................................27
replacing............................................................................73

Copyright © 2010, Juniper Networks, Inc. 169

MX80 3D Universal Edge Router Hardware Guide

cable management bracket show chassis fpc pic-status......................................70

description...........................................................................7 for MIC status.........................................................63
fiber-optic cable, use with.........................................64 show chassis hardware..............................................159
cables See AC power supply cord See DC power show chassis environment pem...............................70
supply cable traceroute..........................................................................67
auxiliary or console port (for Routing Engine comments, in configuration statements.......................xix
management) compatibility, electromagnetic........................................150
connecting during initial installation..............42 compliance
Ethernet port (for Routing Engine EMC requirements.........................................................131
management) general standards........................................................129
connecting during initial installation..............41 components
fiber-optic air filter..................................................................................8
attenuation.............................................................153 base board..........................................................................6
cleaning instructions for transceivers...........64 cable management bracket..........................................7
dispersion...............................................................153 chassis..................................................................................5
multimode and single-mode..........................153 cooling system...................................................................8
transmission distance, maximum.................153 fan tray..................................................................................8
wavelength ranges..............................................153 front panel...........................................................................9
for grounding the router............................................140 MICs......................................................................................13
MIC overview...............................................................................5
connecting during maintenance.....................83 packing for shipment..................................................166
disconnecting.........................................................83 configuration
maintaining.............................................................64 router..................................................................................55
replacing...................................................................83 console port (for Routing Engine management)
power See AC power cord cable
Canada Class A notice.........................................................131 connection during initial installation.............42
Canada electronic emission Class A notice.................131 connector pinout (RJ-45)........................157, 158
case number, for JTAC.........................................................164 specifications........................................................156
chassis conventions
alarm messages See alarm, messages notice icons....................................................................xviii
description..........................................................................5 text and syntax.............................................................xviii
serial number.................................................................160 cooling system
checklist for site preparation..............................................23 description..........................................................................8
chromatic dispersion in fiber-optic cable....................153 troubleshooting..............................................................69
Class A electronic emission notice curly braces, in configuration statements.....................xix
Canada..............................................................................131 customer support....................................................................xx
cleaning instructions contacting.......................................................................164
fiber-optic transceivers...............................................64 contacting JTAC...............................................................xx
clearance, around rack..........................................................26
CLI D
as troubleshooting tool................................................67 DC power
command connecting........................................................................49
to display chassis alarm messages................67 consumption..................................................................146
to display MIC status...........................................63 provisioning....................................................................146
to display power supply status........................70 source cabling...............................................................149
to display serial number...................................159 DC power circuit breaker....................................................148
commands DC power supply
ping......................................................................................67 cables See DC power supply cable
show chassis alarms......................................67, 69, 70 installing...........................................................................90

170 Copyright © 2010, Juniper Networks, Inc.

 Index

removing...........................................................................88 replacing............................................................................75
replacing...........................................................................88 troubleshooting..............................................................69
DC power supply cable fiber-optic
connecting........................................................................93 power budget calculation.........................................154
disconnecting..................................................................92 fire safety specifications....................................................105
lugs.....................................................................................149 font conventions...................................................................xviii
replacing............................................................................92 front panel
specifications.......................................................149, 150 description..........................................................................9
DC specifications LEDs
electrical..........................................................................146 alarm (red and yellow).........................................11
dispersion in fiber-optic cable..........................................153 link................................................................................12
documentation Routing Engine........................................................12
comments on..................................................................xix system........................................................................12
dual-wide MICs
installing...........................................................................80 G
grounding (electrical) specifications
E cable.................................................................................140
earthquakes cable lug..........................................................................140
tested toleration for seismic.....................................137 points on chassis..........................................................139
electrical specifications..............................................141, 146 grounding cables
electricity lug specifications.........................................................140
safety warnings.............................................................120 specifications................................................................140
site wiring guidelines...................................................150 grounding points....................................................................139
electromagnetic guidelines See specifications
compatibility See EMC
pulse..................................................................................150 H
electronic emission Class A notice higher-order mode loss (HOL).........................................153
Canada..............................................................................131 humidity (relative), acceptable........................................137
electrostatic bag
using to store components......................................104 I
EMC (EMI) immunity standards.............................................................129
compliance with requirements................................131 installation instructions
standards........................................................................129 AC power supply............................................................86
suppression....................................................................150 AC power, connecting...................................................47
EMP............................................................................................150 air filter................................................................................74
environmental specifications............................................137 cable, auxiliary or console port (for Routing
ESD Engine management)
preventing damage to components by...............104 during initial installation.....................................42
Ethernet port (for Routing Engine management) tools required...........................................................41
cable cable, Ethernet port (for Routing Engine
connection during initial installation..............41 management)
specifications........................................................156 during initial installation......................................41
tools required...........................................................41
F cable, line card port
fan tray tools required...........................................................41
description..........................................................................8 cable, MIC
installing............................................................................76 for maintenance or replacement....................83
maintaining......................................................................62
removing............................................................................75

Copyright © 2010, Juniper Networks, Inc. 171

MX80 3D Universal Edge Router Hardware Guide

chassis M
tools required..........................................................37 maintenance
unpacking..................................................................31 MIC cables........................................................................64
DC power supply............................................................90 warnings............................................................................115
DC power, connecting..................................................49 maintenance guidelines
dual-wide MICs..............................................................80 air filter...............................................................................62
fan tray...............................................................................76 fan tray...............................................................................62
MICs.....................................................................................78 MIC.......................................................................................63
parts received, verifying...............................................32 overview.............................................................................61
power and grounding cables Routing Engine................................................................66
tools required..........................................................45 manuals
SFP......................................................................................96 comments on..................................................................xix
transceiver........................................................................96 MIC cables
unpacking the router......................................................31 maintaining......................................................................64
XFP......................................................................................96 removing............................................................................83
instructions replacing............................................................................83
cleaning See cleaning instructions MICs
maintenance See maintenance guidelines built-in 10-Gigabit Ethernet
MIC.............................................................................64 description................................................................13
site preparation...............................................................23 built-in Tri-Rate
interface description................................................................14
network............................................................................153 cable
interference installation instructions......................................83
electromagnetic...........................................................150 description.........................................................................13
radio frequency.............................................................150 dual-wide, installing.....................................................80
installing............................................................................78
J LEDs
Japan VCCI notice See Japan voluntary control on components.......................................................15
council for interference notice LEDs on front panel........................................................12
Japan voluntary control council for interference maintaining......................................................................63
notice.....................................................................................132 removing.............................................................................77
replaceable
L description................................................................15
LEDs replacing............................................................................76
alarm (red and yellow on front panel) serial number.................................................................162
description.................................................................11 status, checking..............................................................63
link.........................................................................................12 troubleshooting..............................................................70
MIC..................................................................................12, 15 modal dispersion in fiber-optic cable............................153
on components..............................................................68 mode loss, higher-order......................................................153
on front panel....................................................................11 Modular Interface Cards See MICs
Routing Engine.................................................................12 multimode fiber-optic cable See cable, fiber-optic
system.................................................................................12
link loss, calculating..............................................................155 N
lithium battery compliance...............................................133 NEBS standards....................................................................129
lugs notice icons.............................................................................xviii
for DC power cables....................................................149
for grounding cables...................................................140

172 Copyright © 2010, Juniper Networks, Inc.

 Index

notices R
Canada, Class A.............................................................131 rack
Japan voluntary control council for clearance around, required.........................................26
interference.................................................................132 rack mounting
voluntary control council for interference, moving brackets.............................................................35
Japan.............................................................................132 radio frequency interference, preventing.....................150
relative humidity, acceptable............................................137
O removal instructions
open-frame rack See rack AC power supply............................................................85
overview air filter................................................................................73
router.....................................................................................3 cable, MIC.........................................................................83
DC power supply............................................................88
P fan tray................................................................................75
parentheses, in syntax descriptions................................xix MICs.....................................................................................77
physical specifications........................................................135 SFP......................................................................................94
ping command.........................................................................67 transceiver........................................................................94
pinouts XFP......................................................................................94
RJ-45 cable connector ports replacement instructions
(auxiliary/console)..................................................158 AC power supply............................................................85
RJ-45 Ethernet cable connector port....................157 AC power supply cord...................................................87
plug types air filter................................................................................73
AC.......................................................................................143 cable, MIC.........................................................................83
power DC power supply............................................................88
budget calculation.......................................................154 DC power supply cable................................................92
cables and cords See AC power supply cord fan tray................................................................................75
See DC power supply cable MIC.......................................................................................76
connecting AC..................................................................47 SFP......................................................................................94
connecting DC.................................................................49 XFP......................................................................................94
margin calculation.......................................................155 requirements See specifications
surges...............................................................................150 RFI...............................................................................................150
system RJ-45 cable connector pinouts........................................157
specifications........................................................139 RJ-45 cable connector pinouts (auxiliary and
power supply console ports)....................................................................158
AC electrical specifications.......................................141 router
cables and cords See AC power See DC power component overview......................................................5
DC electrical specifications......................................146 configuration....................................................................55
serial number.................................................................163 parts list.............................................................................32
power system serial number.................................................................160
AC electrical specifications.......................................141 Routing Engine
DC electrical specifications......................................146 LED........................................................................................12
troubleshooting..............................................................70 maintaining......................................................................66
powering off the router.........................................................53
powering on the router S
AC.........................................................................................47 safety information................................................................102
DC..........................................................................................51 See also warnings
provisioning safety standards....................................................................129
AC power.........................................................................142 seismic (earthquake)...........................................................137
DC power.........................................................................146

Copyright © 2010, Juniper Networks, Inc. 173

MX80 3D Universal Edge Router Hardware Guide

serial number system

chassis.............................................................................160 LED........................................................................................12
in output from show chassis hardware
command...................................................................159 T
MIC.....................................................................................162 technical support
power supply..................................................................163 contacting JTAC...............................................................xx
SFP telco rack See rack
description.......................................................................94 temperature, acceptable range........................................137
installing............................................................................96 thermal output.......................................................................137
removing...........................................................................94 tolerances.................................................................................137
replacing............................................................................94 tools required
show chassis alarms command.........................67, 69, 70 maintaining.......................................................................61
show chassis fpc pic-status...............................................70 traceroute command.............................................................67
show chassis fpc pic-status command transceiver
for MIC status..................................................................63 installing............................................................................96
show chassis hardware command................................159 removing...........................................................................94
show chassis environment pem command.................70 transmission distances, fiber-optic cable...................153
signal dispersion....................................................................153 Tri-Rate MIC (built-in)
signaling, distance limitations.........................................150 description.........................................................................14
single-mode fiber-optic cable See cable, fiber-optic troubleshooting
site CLI commands................................................................67
electrical wiring specifications................................150 cooling system................................................................69
environmental specifications...................................137 fans.....................................................................................69
preparation MICs.....................................................................................70
instructions..............................................................23 power system..................................................................70
preparation checklist....................................................23
routine inspection of......................................................61 U
specifications unpacking the router
AC power cord...............................................................143 tools required....................................................................31
cable..................................................................................153
power.......................................................................150 V
Routing Engine management ports.............156 VCCI notice See voluntary control council for
clearance around rack..................................................26 interference notice
DC power cable.............................................................150 voluntary control council for interference notice
electrical..........................................................................143 Japan.................................................................................132
cable and wiring...................................................150
environmental................................................................137 W
fire safety.........................................................................105 warnings
physical............................................................................135 electrical..........................................................................120
power levels defined..................................................................99
system.....................................................................139 maintenance and operational..................................115
thermal output...............................................................137 wavelength ranges supported by fiber-optic
standards compliance........................................................129 cable......................................................................................153
startup, system wiring, electrical See electricity
monitoring...................................................................47, 51
support, technical See technical support
X
XFP
surge protection....................................................................150
description.......................................................................94
syntax conventions..............................................................xviii
installing............................................................................96

174 Copyright © 2010, Juniper Networks, Inc.

 Index

removing...........................................................................94
replacing............................................................................94

Copyright © 2010, Juniper Networks, Inc. 175

MX80 3D Universal Edge Router Hardware Guide

176 Copyright © 2010, Juniper Networks, Inc.