Scribd
Upload
32 views4 pages

ELEE37417D - Lab8 - Akash Fumakia

This document summarizes key parameters of the LM2735 switching voltage regulator including: 1. An input voltage range of 2.7-5.5V and output voltage range of 3-24V. 2. Minimum and maximum duty cycles of 96-5% and 99-2% respectively. 3. Current limiting, soft start, and enable pin functions for protection and control. 4. An equation relating output voltage, input voltage, and duty cycle.

Uploaded by

hritik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
32 views4 pages

ELEE37417D - Lab8 - Akash Fumakia

This document summarizes key parameters of the LM2735 switching voltage regulator including: 1. An input voltage range of 2.7-5.5V and output voltage range of 3-24V. 2. Minimum and maximum duty cycles of 96-5% and 99-2% respectively. 3. Current limiting, soft start, and enable pin functions for protection and control. 4. An equation relating output voltage, input voltage, and duty cycle.

Uploaded by

hritik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Lab 8

Switching Voltage Regulators


Submitted by:
Akash Fumakia
991 345 556

Sheridan College
ELEE37417D

March 22nd, 2022


Part A
Part B:

LM2735 Datasheet
Parameter Value Unit Note
Input Voltage Range 2.7 – 5.5 V
Output Voltage Range 3 – 24 V
Minimum Duty Cycle X: 96, Y:99 %
Maximum Duty Cycle X: 5, Y:2 %
Maximum Output Current 1 A

Question 3:
1. Current Limit: To protect the internal NMOS switch, the LM2735 has a cycle by
cycle current limiting.
2. Soft Start: This allows Vout to increase at a controlled rate during start up.This
happens by slowly ramping nominal value of 1.255 V in about 4 ms.
3. Enable Pin : Enable pin is a switch which puts LM2735 in shutdown mode. When
low voltage is applied to enable pin, the part enters shutdown mode by bringing
current down to 80 nA.
4. Vout/Vin versus Duty Cycle (Equation):
𝑉𝑉𝑜𝑜𝑜𝑜𝑜𝑜 1
=
𝑉𝑉𝑖𝑖𝑖𝑖 𝐷𝐷′
𝑉𝑉 − 𝑉𝑉
Therefore: 𝐷𝐷 = 𝑜𝑜𝑜𝑜𝑜𝑜𝑉𝑉 𝑖𝑖𝑖𝑖
𝑜𝑜𝑜𝑜𝑜𝑜

Part C
Question 4:
Vin = 3.5V

Figure 1: Circuit for 3.5V


Vin = 5 V

Figure 2: Circuit for 5V

Vin I in Vout Iout


3.5V 1.516A 11.911 V 348.293 mA
5V 975.671 mA 11.911 V 348.229 mA

Question 5
𝛥𝛥𝑉𝑉𝑜𝑜𝑜𝑜𝑜𝑜 /𝑉𝑉𝑜𝑜𝑜𝑜𝑜𝑜
Line regulation = ∗ 100%
𝛥𝛥𝑉𝑉𝑖𝑖𝑖𝑖

(11.911−11.911)/11.911
Line regulation = ∗ 100%
5−3.5

Line regulation = 0%

Question 6
𝛥𝛥𝑉𝑉𝑜𝑜𝑜𝑜𝑜𝑜 ∗ 𝐼𝐼𝑜𝑜𝑜𝑜𝑜𝑜
Efficiency = ∗ 100%
𝛥𝛥𝑉𝑉𝑖𝑖𝑖𝑖 ∗𝐼𝐼𝑖𝑖𝑖𝑖

11.911𝑉𝑉 ∗ 0.348 𝐴𝐴
3.5 V Efficiency = ∗ 100%
3.5 𝑉𝑉∗1.516 𝐴𝐴

Efficiency = 78.12%

11.911𝑉𝑉 ∗ 0.348 𝐴𝐴
5V Efficiency = ∗ 100%
5 𝑉𝑉∗0.976 𝐴𝐴

Efficiency = 85%

You might also like