Scribd
Upload
79 views24 pages

4-Combined Stress

The document contains examples of mechanical engineering problems involving the calculation of stresses in shafts subjected to torque, bending moment, thrust force, and loads. The examples calculate maximum stress in a shaft under torque and bending, diameter for a shaft under torque and bending with given allowable stresses, and required diameter for a shaft under thrust and load with given yield stress and safety factor.

Uploaded by

Jiff Corre504
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
79 views24 pages

4-Combined Stress

The document contains examples of mechanical engineering problems involving the calculation of stresses in shafts subjected to torque, bending moment, thrust force, and loads. The examples calculate maximum stress in a shaft under torque and bending, diameter for a shaft under torque and bending with given allowable stresses, and required diameter for a shaft under thrust and load with given yield stress and safety factor.

Uploaded by

Jiff Corre504
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 24

CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY
Example:
A 150 mm diameter shaft is subjected to a torque of 16 KN.m and
a bending moment of 12.5 KN.m. Find the maximum stress
developed.

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY
Example:
A round steel shaft rotates at 200 rpm and is subjected to a torque
of 225 N.m and a bending moment of 350 N.m. The allowable
shearing stress is 40 MPa and the allowable bending stress is 60
MPa. Find the diameter.

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY
Example:
A solid shaft subjected to thrust force of 1000 lb and carries a 5000
lb load at the center of the shaft. If the shaft length is 10 ft, what is
the required shaft diameter for a yield stress in torsion of 110,000
psi and a factor of safety of 2.5?

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING


CEBU INSTITUTE OF TECHNOLOGY - UNIVERSITY

DEPARTMENT OF MECHANICAL ENGINEERING

You might also like